This removes the various DBG() macro from the powerpc PCI code and
makes it use the standard pr_debug instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update memcpy() to add two new feature sections: one for aligning the
destination before copying and one for copying using aligned load
and store doubles.
These new feature sections will only affect Power6 and Cell because
the CPU feature bit was only added to these two processors.
Power6 gets its best performance in memcpy() when aligning neither the
source nor the destination, while Cell gets its best performance when
just the destination is aligned. But in order to save on CPU feature
bits we can use the previously added CPU_FTR_CP_USE_DCBTZ feature bit
to differentiate between Power6 and Cell (because CPU_FTR_CP_USE_DCBTZ
was added to Cell but not Power6).
The first feature section acts to nop out the branch that takes us to
the code that aligns us to an eight byte boundary for the destination.
We only want to nop out this branch on Power6.
So the ALT_FTR_SECTION_END() for this feature section creates a test
mask of the two feature bits ORed together and provides an expected
result of just CPU_FTR_UNALIGNED_LD_STD, thus we nop out the branch
if we're on a CPU that has CPU_FTR_UNALIGNED_LD_STD set and
CPU_FTR_CP_USE_DCBTZ unset.
For the second feature section added, if we're on a CPU that has the
CPU_FTR_UNALIGNED_LD_STD bit set then we don't want to do the copy
with aligned loads and stores (and the appropriate shifting left and
right instructions), so we want to nop out the branch to
.Lsrc_unaligned.
The andi. used for this branch is moved to just above the branch
because this allows us to nop out both instructions with just one
feature section which gives us better performance and doesn't hurt
readability which two separate feature sections did.
Moving the andi. to just above the branch doesn't have any noticeable
negative effect on the remaining 64bit processors (the ones that
didn't have this feature bit added).
On Cell this simple modification results in an improvement to measured
memcpy() bandwidth of up to 50% in the hot cache case and up to 15% in
the cold cache case.
On Power6 we get memory bandwidth results that are up to three times
faster in the hot cache case and up to 50% faster in the cold cache
case.
Commit 2a9294369b ("powerpc: Add new CPU
feature: CPU_FTR_CP_USE_DCBTZ") was where CPU_FTR_CP_USE_DCBTZ was
added.
To say that Cell gets its best performance in memcpy() with just the
destination aligned is true but only for the reason that the indirect
shift and rotate instructions, sld and srd, are microcoded on Cell.
This means that either the destination or the source can be aligned,
but not both, and seeing as we get better performance with the
destination aligned we choose this option.
While we're at it make a one line change from cmpldi r1,... to
cmpldi cr1,... for consistency.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a new CPU feature bit, CPU_FTR_UNALIGNED_LD_STD, to be added
to the 64bit powerpc chips that can do unaligned load double and
store double without any performance hit.
This is added to Power6 and Cell and will be used in the next commit
to disable the code that gets the destination address aligned on
those CPUs where doing that doesn't improve performance.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A new field has been added to the VPA as a method for the client OS to
communicate to firmware the number of page-ins it is performing when
running collaborative memory overcommit. The hypervisor will use this
information to better determine if a partition is experiencing memory
pressure and needs more memory allocated to it.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 'ibm,interrupt-server#-size' properties are not in the cpu nodes,
which is where we currently look for them, but rather live under the
interrupt source controller nodes (which have "ibm,ppc-xics" in their
compatible property).
This moves the code that looks for the ibm,interrupt-server#-size
properties from xics_update_irq_servers() into xics_init_IRQ().
Also this adds a check for mismatched sizes across the interrupt
source controller nodes. Not sure this is necessary as in this case
the firmware might be seriously busted.
This property only appears on POWER6 boxes and is only used in the
set-indicator(gqirm) call, and apparently firmware currently ignores
the value we pass. Nevertheless we need to fix it in case future
firmware versions use it.
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We don't want to encourage the device_type usage. It isn't used in
the code, so we can simply remove it from the dts files.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When no hardware method is provided to sync the timebase registers
across the machine, and the platform doesn't sync them for us, then we
use a generic software implementation. Currently, the code for that
has many printks, and they don't have log levels. Most of the printks
are only useful for debugging the code, and since we haven't had any
problems with it for years, this turns them into pr_debug.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code to properly expose domain numbers in /proc is somewhat
bogus on ppc64 as it depends on the "buid" field being non-0,
but that field is really pseries specific.
This removes that code and makes ppc64 use the same code as 32-bit
which effectively decides whether to expose domains based on
ppc_pci_flags set by the platform, and sets the default for 64-bit
to enable domains and enable compatibility for domain 0 (which
strips the domain number for domain 0 to help with X servers).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This gets rid of this build warning:
arch/powerpc/platforms/pseries/pci_dlpar.c: In function 'init_phb_dynamic':
arch/powerpc/platforms/pseries/pci_dlpar.c:192: warning: unused variable 'b'
This is one of the very few warnings left in a ppc64_defconfig build and
getting rid of it will make it easier to see future introduced ones (in
fact this was introduced very recently).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes this error on Cell when CONFIG_KEXEC = n:
arch/powerpc/platforms/cell/ras.c:299: error: implicit declaration of function 'crash_shutdown_register'
We have to include <asm/kexec.h> because it contains the dummy
definition of crash_shutdown_register that is used when
CONFIG_KEXEC=n, but <linux/kexec.h> doesn't include <asm/kexec.h> in
that case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Compiling with CONFIG_SMP = n and CONFIG_PS3_LPM != n gives this error:
drivers/ps3/ps3-lpm.c:838: error: implicit declaration of function 'get_hard_smp_processor_id'
This fixes it. We have to include <asm/smp.h> rather than
<linux/smp.h> because the UP definition of get_hard_smp_processor_id()
is in <asm/smp.h>, and <linux/smp.h> only includes <asm/smp.h> if
CONFIG_SMP = y.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
xfrm: Fix xfrm_policy_gc_lock handling.
niu: Use pci_ioremap_bar().
bnx2x: Version Update
bnx2x: Calling netif_carrier_off at the end of the probe
bnx2x: PCI configuration bug on big-endian
bnx2x: Removing the PMF indication when unloading
mv643xx_eth: fix SMI bus access timeouts
net: kconfig cleanup
fs_enet: fix polling
XFRM: copy_to_user_kmaddress() reports local address twice
SMC91x: Fix compilation on some platforms.
udp: Fix the SNMP counter of UDP_MIB_INERRORS
udp: Fix the SNMP counter of UDP_MIB_INDATAGRAMS
drivers/net/smc911x.c: Fix lockdep warning on xmit.
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: mask off DET when restoring SControl for detach
libata: implement ATA_HORKAGE_ATAPI_MOD16_DMA and apply it
libata: Fix a potential race condition in ata_scsi_park_show()
sata_nv: fix generic, nf2/3 detection regression
sata_via: restore vt*_prepare_host error handling
sata_promise: add ATA engine reset to reset ops
libata restores SControl on detach; however, trying to restore
non-zero DET can cause undeterministic behavior including PMP device
going offline till power cycling. Mask off DET when restoring
SControl.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata always uses PIO for ATAPI commands when the number of bytes to
transfer isn't multiple of 16 but quantum DAT72 chokes on odd bytes
PIO transfers. Implement a horkage to skip the mod16 check and apply
it to the quantum device.
This is reported by John Clark in the following thread.
http://thread.gmane.org/gmane.linux.ide/34748
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: John Clark <clarkjc@runbox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Peter Moulder has pointed out that there is a slight chance that a
negative value might be passed to jiffies_to_msecs() in
ata_scsi_park_show(). This is fixed by saving the value of jiffies in a
local variable, thus also reducing code since the volatile variable
jiffies is accessed only once.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Tejun Heo <tj.kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
All three flavors of sata_nv's are different in how their hardreset
behaves.
* generic: Hardreset is not reliable. Link often doesn't come online
after hardreset.
* nf2/3: A little bit better - link comes online with longer debounce
timing. However, nf2/3 can't reliable wait for the first D2H
Register FIS, so it can't wait for device readiness or classify the
device after hardreset. Follow-up SRST required.
* ck804: Hardreset finally works.
The core layer change to prefer hardreset and follow up changes
exposed the above issues and caused various detection regressions for
all three flavors. This patch, hopefully, fixes all the known issues
and should make sata_nv error handling more reliable.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
commit b9d5b89b48 (sata_via: fix support
for 5287) accidently (?) removed vt*_prepare_host error handling - restore it
catched by gcc:
drivers/ata/sata_via.c: In function 'svia_init_one':
drivers/ata/sata_via.c:567: warning: 'host' may be used uninitialized in this function
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Promise ATA engines need to be reset when errors occur.
That's currently done for errors detected by sata_promise itself,
but it's not done for errors like timeouts detected outside of
the low-level driver.
The effect of this omission is that a timeout tends to result
in a sequence of failed COMRESETs after which libata EH gives
up and disables the port. At that point the port's ATA engine
hangs and even reloading the driver will not resume it.
To fix this, make sata_promise override ->hardreset on SATA
ports with code which calls pdc_reset_port() on the port in
question before calling libata's hardreset. PATA ports don't
use ->hardreset, so for those we override ->softreset instead.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
From: Alexey Dobriyan <adobriyan@gmail.com>
Based upon a lockdep trace by Simon Arlott.
xfrm_policy_kill() can be called from both BH and
non-BH contexts, so we have to grab xfrm_policy_gc_lock
with BH disabling.
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_carrier_off was called too early at the probe. In case of failure
or simply bad timing, this can cause a fatal error since linkwatch_event
might run too soon.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code read nothing but zeros on big-endian (wrong part of the
32bits). This caused poor performance on big-endian machines. Though this
issue did not cause the system to crash, the performance is significantly
better with the fix so I view it as critical bug fix.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PMF flag is set, the driver can access the HW freely. When the
driver is unloaded, it should not access the HW. The problem caused fatal
errors when "ethtool -i" was called after the calling instance was unloaded
and another instance was already loaded
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv643xx_eth mii bus implementation uses wait_event_timeout() to
wait for SMI completion interrupts.
If wait_event_timeout() would return zero, mv643xx_eth would conclude
that the SMI access timed out, but this is not necessarily true --
wait_event_timeout() can also return zero in the case where the SMI
completion interrupt did happen in time but where it took longer than
the requested timeout for the process performing the SMI access to be
scheduled again. This would lead to occasional SMI access timeouts
when the system would be under heavy load.
The fix is to ignore the return value of wait_event_timeout(), and
to re-check the SMI done bit after wait_event_timeout() returns to
determine whether or not the SMI access timed out.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The bool kconfig option added to ixgbe and myri10ge for DCA is ambigous,
so this patch adds a description to the kconfig option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: fix renaming one hardlink on top of another
[CIFS] fix error in smb_send2
[CIFS] Reduce number of socket retries in large write path
cifs: fix renaming one hardlink on top of another
POSIX says that renaming one hardlink on top of another to the same
inode is a no-op. We had the logic mostly right, but forgot to clear
the return code.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing, ring-buffer: add paranoid checks for loops
ftrace: use kretprobe trampoline name to test in output
tracing, alpha: undefined reference to `save_stack_trace'
* 'io-mappings-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
io mapping: clean up #ifdefs
io mapping: improve documentation
i915: use io-mapping interfaces instead of a variety of mapping kludges
resources: add io-mapping functions to dynamically map large device apertures
x86: add iomap_atomic*()/iounmap_atomic() on 32-bit using fixmaps
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda: make a STAC_DELL_EQ option
ALSA: emu10k1 - Add more invert_shared_spdif flag to Audigy models
ALSA: hda - Add a quirk for another Acer Aspire (1025:0090)
ALSA: remove direct access of dev->bus_id in sound/isa/*
sound: struct device - replace bus_id with dev_name(), dev_set_name()
ALSA: Fix PIT lockup on some chipsets when using the PC-Speaker
ALSA: rawmidi - Add open check in rawmidi callbacks
ALSA: hda - Add digital-mic for ALC269 auto-probe mode
ALSA: hda - Disable broken mic auto-muting in Realtek codes
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
i915: Add GEM ioctl to get available aperture size.
drm/radeon: fixup further bus mastering confusion.
build fix: CONFIG_DRM_I915=y && CONFIG_ACPI=n
Impact: cleanup
clean up ifdefs: change #ifdef CONFIG_X86_32/64 to
CONFIG_HAVE_ATOMIC_IOMAP.
flip around the #ifdef sections to clean up the structure.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add support for explicitly enabling the EQ distortion hack for
systems without software biquad support.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While writing a new tracer, I had a bug where I caused the ring-buffer
to recurse in a bad way. The bug was with the tracer I was writing
and not the ring-buffer itself. But it took a long time to find the
problem.
This patch adds paranoid checks into the ring-buffer infrastructure
that will catch bugs of this nature.
Note: I put the bug back in the tracer and this patch showed the error
nicely and prevented the lockup.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: ia64+tracing build fix
When a function is kprobed, the return address is set to the
kprobe_trampoline, or something similar. This caused the output
of the trace to look confusing when the parent seemed to be this
"kprobe_trampoline" function.
To fix this, Abhishek Sagar added a test of the instruction pointer
of the parent to see if it matched the kprobe_trampoline. If it
did, the output would print a "[unknown/kretprobe'd]" instead.
Unfortunately, not all archs do this the same way, and the trampoline
function may not be exported, which causes failures in builds.
This patch will compare the name instead of the pointer to see
if it matches. This prevents us from depending on a function from
being exported, and should work on all archs. The worst that can
happen is that an arch might use a different name and then we
go back to the confusing output. At least the arch will still build.
Reported-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Acked-by: Abhishek Sagar <sagar.abhishek@gmail.com>
While adding support for MIGRATE/KMADDRESS in strongSwan (as specified
in draft-ebalard-mext-pfkey-enhanced-migrate-00), Andreas Steffen
noticed that XFRMA_KMADDRESS attribute passed to userland contains the
local address twice (remote provides local address instead of remote
one).
This bug in copy_to_user_kmaddress() affects only key managers that use
native XFRM interface (key managers that use PF_KEY are not affected).
For the record, the bug was in the initial changeset I posted which
added support for KMADDRESS (13c1d18931
'xfrm: MIGRATE enhancements (draft-ebalard-mext-pfkey-enhanced-migrate)').
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Reported-by: Andreas Steffen <andreas.steffen@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: build fix on !stacktrace architectures
only select STACKTRACE on architectures that have STACKTRACE_SUPPORT
... since we also need to ifdef out the guts of ftrace_trace_stack().
We also want to disallow setting TRACE_ITER_STACKTRACE in trace_flags
on such configs, but that can wait.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Added a quirk for another Acer Aspier laptop (1025:0090) with ALC883
codec. Reported in Novell bnc#426935:
https://bugzilla.novell.com/show_bug.cgi?id=426935
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts 51ac3beffd ('SMC91x: delete
unused local variable "lp"') and adds __maybe_unused markers to these
(potentially) unused variables.
The issue is that in some configurations SMC_IO_SHIFT evaluates
to '(lp->io_shift)', but in some others it's plain '0'.
Based upon a build failure report from Manuel Lauss.
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed the direct accesses of dev->bus_id in sound/isa/* by replacement
with dev_err() or dev_warn() functions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[stripped sound/isa/* changes, replaced with the next patch -- tiwai]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Benjamin Herrenschmidt
Mark Nelson
Brian King
Sebastien Dugue
Anton Vorontsov
Stephen Rothwell
Alexey Dobriyan
Linus Torvalds
Jianjun Kong
Tejun Heo
Elias Oltmanns
Marcin Slusarz
Mikael Pettersson
David S. Miller
Eilon Greenstein
Lennert Buytenhek
Jeff Kirsher
Jeff Layton
Keith Packard
Takashi Iwai
Matthew Ranostay
Steven Rostedt
Arnaud Ebalard
Al Viro
Kay Sievers
Zoltan Devai