ACP driver should send SHA DMA completion command to PSP module for RN
platform only.
Add a revision check for RN platform.
Signed-off-by: Mastan Katragadda <Mastan.Katragadda@amd.com>
Link: https://lore.kernel.org/r/20230630070544.2167421-1-Mastan.Katragadda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Following prints are observed while testing audio on Jetson AGX Orin which
has onboard RT5640 audio codec:
BUG: sleeping function called from invalid context at kernel/workqueue.c:3027
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 0, name: swapper/0
preempt_count: 10001, expected: 0
RCU nest depth: 0, expected: 0
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/irq/handle.c:159 __handle_irq_event_percpu+0x1e0/0x270
---[ end trace ad1c64905aac14a6 ]-
The IRQ handler rt5640_irq() runs in interrupt context and can sleep
during cancel_delayed_work_sync().
Fix this by running IRQ handler, rt5640_irq(), in thread context.
Hence replace request_irq() calls with devm_request_threaded_irq().
Fixes: 051dade346 ("ASoC: rt5640: Fix the wrong state of JD1 and JD2")
Cc: stable@vger.kernel.org
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1688015537-31682-4-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Byte mask for channel-1 of stream-1 is not getting enabled and this
causes failures during ADX use cases. This happens because the byte
map value 0 matches the byte map array and put() callback returns
without enabling the corresponding bits in the byte mask.
ADX supports 4 output streams and each stream can have a maximum of
16 channels. Each byte in the input frame is uniquely mapped to a
byte in one of these 4 outputs. This mapping is done with the help of
byte map array via user space control setting. The byte map array
size in the driver is 16 and each array element is of size 4 bytes.
This corresponds to 64 byte map values.
Each byte in the byte map array can have any value between 0 to 255
to enable the corresponding bits in the byte mask. The value 256 is
used as a way to disable the byte map. However the byte map array
element cannot store this value. The put() callback disables the byte
mask for 256 value and byte map value is reset to 0 for this case.
This causes problems during subsequent runs since put() callback,
for value of 0, just returns without enabling the byte mask. In short,
the problem is coming because 0 and 256 control values are stored as
0 in the byte map array.
Right now fix the put() callback by actually looking at the byte mask
array state to identify if any change is needed and update the fields
accordingly. The get() callback needs an update as well to return the
correct control value that user has set before. Note that when user
set 256, the value is stored as 0 and byte mask is disabled. So byte
mask state is used to either return 256 or the value from byte map
array.
Given above, this looks bit complicated and all this happens because
the byte map array is tightly packed and cannot actually store the 256
value. Right now the priority is to fix the existing failure and a TODO
item is put to improve this logic.
Fixes: 3c97881b8c ("ASoC: tegra: Fix kcontrol put callback in ADX")
Cc: stable@vger.kernel.org
Signed-off-by: Sheetal <sheetal@nvidia.com>
Reviewed-by: Mohan Kumar D <mkumard@nvidia.com>
Reviewed-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1688015537-31682-3-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Byte mask for channel-1 of stream-1 is not getting enabled and this
causes failures during AMX use cases. This happens because the byte
map value 0 matches the byte map array and put() callback returns
without enabling the corresponding bits in the byte mask.
AMX supports 4 input streams and each stream can take a maximum of
16 channels. Each byte in the output frame is uniquely mapped to a
byte in one of these 4 inputs. This mapping is done with the help of
byte map array via user space control setting. The byte map array
size in the driver is 16 and each array element is of size 4 bytes.
This corresponds to 64 byte map values.
Each byte in the byte map array can have any value between 0 to 255
to enable the corresponding bits in the byte mask. The value 256 is
used as a way to disable the byte map. However the byte map array
element cannot store this value. The put() callback disables the byte
mask for 256 value and byte map value is reset to 0 for this case.
This causes problems during subsequent runs since put() callback,
for value of 0, just returns without enabling the byte mask. In short,
the problem is coming because 0 and 256 control values are stored as
0 in the byte map array.
Right now fix the put() callback by actually looking at the byte mask
array state to identify if any change is needed and update the fields
accordingly. The get() callback needs an update as well to return the
correct control value that user has set before. Note that when user
sets 256, the value is stored as 0 and byte mask is disabled. So byte
mask state is used to either return 256 or the value from byte map
array.
Given above, this looks bit complicated and all this happens because
the byte map array is tightly packed and cannot actually store the 256
value. Right now the priority is to fix the existing failure and a TODO
item is put to improve this logic.
Fixes: 8db78ace1b ("ASoC: tegra: Fix kcontrol put callback in AMX")
Cc: stable@vger.kernel.org
Signed-off-by: Sheetal <sheetal@nvidia.com>
Reviewed-by: Mohan Kumar D <mkumard@nvidia.com>
Reviewed-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1688015537-31682-2-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For invalid dai id, instead of returning -EINVAL
return bytes count as zero in acp_get_byte_count() function.
Fixes: 623621a9f9 ("ASoC: amd: Add common framework to support I2S on ACP SOC")
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230626105356.2580125-6-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
acp_get_byte_count() function should return zero bytes instead of
-EINVAL for invalid SoundWire manager instance.
Fixes: f722917350 ("ASoC: amd: ps: add SoundWire dma driver dma ops")
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230626105356.2580125-5-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For AUDIO0 RX stream, AUDIO0_RX position registers should be used.
DMA error is reported due to referring wrong position register set for
AUDIO0 RX stream.
Correct the position register set for AUDIO0 RX stream.
Fixes: f722917350 ("ASoC: amd: ps: add SoundWire dma driver dma ops")
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230626105356.2580125-3-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct the DMA irq mask macro to program DMA irq bits correctly for
SDW0 instance rx streams.
Fixes: 298d4f7b17 ("ASoC: amd: ps: add support for SoundWire DMA interrupts")
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230626105356.2580125-2-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add comments for DMA stream id and IRQ bit mapping in
ACP_EXTERNAL_CNTL & ACP_EXTERNAL_CNTL1 registers for
SDW0 and SDW1 manager instances.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230626105356.2580125-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to CTA 861 the channel/speaker allocation info in the
audio infoframe only applies to uncompressed (PCM) audio streams.
The channel count info should indicate the number of channels
in the transmitted audio, which usually won't match the number of
channels used to transmit the compressed bitstream.
Some devices (eg some Sony TVs) will refuse to decode compressed
audio if these values are not set correctly.
To fix this we can simply set the channel count to 0 (which means
"refer to stream header") and set the channel/speaker allocation to 0
as well (which would mean stereo FL/FR for PCM, a safe value all sinks
will support) when transmitting compressed audio.
Signed-off-by: Matthias Reichl <hias@horus.com>
Link: https://lore.kernel.org/r/20230624165232.5751-1-hias@horus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The generic snd_soc_dai_get_dlc() contains a default translation function
for DAI names which has factored out common code in a number of card
drivers, resolving the dai_name and of_node either using a driver provided
translation function or with a generic implementation. Unfortunately the
of_node can't be set by the translation function since it currently doesn't
have an interface to do that but snd_soc_dai_get_dlc() only initialises the
of_node in the case where there is no translation function.
This breaks the Meson support after conversion to use the generic helpers
since the DPCM cards for it check which component of the SoC is connected
to each link by checking the compatible for the component and the Meson
components provide a custom operation so don't use the generic code.
Fix this and potentially other cards by unconditionally storing the node in
the dai_link_component, there shouldn't be a binding specific of_node
selected since that's how we determine the translation function.
Fixes: 2e1dbea1f8 ("ASoC: meson: use snd_soc_{of_}get_dlc()")
Fixes: 3c8b586185 ("ASoC: soc-core.c: add index on snd_soc_of_get_dai_name()")
Link: https://lore.kernel.org/r/Message-Id: <20230623-asoc-fix-meson-probe-v1-1-82b2c2ec5ca4@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return -EINVAL instead of success on this error path.
Fixes: 915f5eadeb ("ASoC: tas2781: firmware lib")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/Message-Id: <729bb6b3-bc1d-4b3d-8b65-077a492c753c@moroto.mountain>
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_allow() is not needed for ACP child platform devices.
Replace pm_runtime_allow() with pm_runtime_mark_last_busy()
& pm_runtime_set_active() in pm_runtime enable sequence for
ACP child platform drivers.
Signed-off-by: Arun Gopal <arungopal.kondaveeti@amd.com>
Link: https://lore.kernel.org/r/Message-Id: <20230623214150.4058721-1-arungopal.kondaveeti@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The new driver has two modules that both get enabled for build testing
when all codecs are selected. The comlib part has an i2c dependency,
so this remains disabled on builds without i2c, but then the other
one fails to link:
ERROR: modpost: "tasdevice_dev_bulk_write" [sound/soc/codecs/snd-soc-tas2781-fmwlib.ko] undefined!
ERROR: modpost: "tasdevice_dev_update_bits" [sound/soc/codecs/snd-soc-tas2781-fmwlib.ko] undefined!
ERROR: modpost: "tasdevice_dev_bulk_read" [sound/soc/codecs/snd-soc-tas2781-fmwlib.ko] undefined!
ERROR: modpost: "tasdevice_dev_read" [sound/soc/codecs/snd-soc-tas2781-fmwlib.ko] undefined!
ERROR: modpost: "tasdevice_dev_write" [sound/soc/codecs/snd-soc-tas2781-fmwlib.ko] undefined!
There are many ways to address this, adding an explicit dependency seems
to be the clearest method that keeps the structure of the driver otherwise
unchanged.
Fixes: ef3bcde75d ("ASoC: tas2781: Add tas2781 driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/Message-Id: <20230622101205.3180938-1-arnd@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
BIOS invokes ACP Power off sequence based on ACP device state.
Remove redundant code from ACP PCI driver for ACP Power off sequence.
Signed-off-by: Syed Saba Kareem <Syed.SabaKareem@amd.com>
Link: https://lore.kernel.org/r/Message-Id: <20230622152406.3709231-4-Syed.SabaKareem@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clear pdm dma interrupt mask in acp_dmic_shutdown().
'Fixes: c32bd332ce ("ASoC: amd: acp: Add generic support for
PDM controller on ACP")'
Signed-off-by: Syed Saba Kareem <Syed.SabaKareem@amd.com>
Link: https://lore.kernel.org/r/Message-Id: <20230622152406.3709231-1-Syed.SabaKareem@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TDM mode for max98090 is dsp_a compatible with such limitations:
1) Up to four timeslots supported.
2) Only 16 bits timeslots supported.
3) Only 2 active timeslots (L/R) supported.
We want to setup TDM mode only when dsp_a mode is selected. So move
M98090_REG_TDM_FORMAT/M98090_REG_TDM_CONTROL registers setup from
max98090_set_tdm_slot() to the max98090_dai_set_fmt(). Also extend
max98090_set_tdm_slot() with all TDM limitations check.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Link: https://lore.kernel.org/r/Message-Id: <20230622142038.63388-1-fido_max@inbox.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the soundcard does not specify the dapm pins, let the common
code add these pins for jack.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/Message-Id: <20230302120327.10823-1-srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The i2s driver uses the mapped __iomem address of the FIFO as the DMA
address for the device. This apparently works on loongarch because of
the way it handles __iomem pointers as aliases of physical addresses,
but this is not portable to other architectures and causes a compiler
warning when dma addresses are not the same size as pointers:
sound/soc/loongson/loongson_i2s_pci.c: In function 'loongson_i2s_pci_probe':
sound/soc/loongson/loongson_i2s_pci.c:110:29: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
110 | tx_data->dev_addr = (dma_addr_t)i2s->reg_base + LS_I2S_TX_DATA;
| ^
sound/soc/loongson/loongson_i2s_pci.c:113:29: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
113 | rx_data->dev_addr = (dma_addr_t)i2s->reg_base + LS_I2S_RX_DATA;
| ^
Change the driver to instead use the physical address as stored in the
PCI BAR resource directly. Since 'dev_addr' is a 32-bit address, I think
this results in the same truncated address on loongarch but is otherwise
closer to portable code and avoids the warning.
Fixes: d84881e068 ("ASoC: Add support for Loongson I2S controller")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/Message-Id: <20230622101235.3230941-1-arnd@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
"enum" values should be integers or strings, not arrays (though json-schema
does allow arrays, we do not). In this case, all possible combinations are
allowed anyways, so there's little point in expressing as an array.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/Message-Id: <20230621231044.3816914-1-robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove stale comments in AHUB driver which is related to DAPM
widgets and routes. This is misleading otherwise.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/Message-Id: <1687433656-7892-7-git-send-email-spujar@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Align with other AHUB module drivers and use normal system
sleep for ASRC as well.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/Message-Id: <1687433656-7892-6-git-send-email-spujar@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, fsl-asoc-card supports passing the width of the TDM slot, but
not the number of slots in use, as it harcodes it as two slots.
Add support for passing the number of slots in use.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20230616203913.551183-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add binding for WSA8840/WSA8845/WSA8845H smart speaker amplifiers used
in Qualcomm QRD8550 board with SM8550 SoC.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230616115751.392886-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Reorder the entries in quirk table to group entries with same platform.
Signed-off-by: Terry Cheong <htcheong@chromium.org>
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Link: https://lore.kernel.org/r/20230616063617.25900-1-mac.chiang@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Vijendar Mukunda <Vijendar.Mukunda@amd.com>:
This patch series add support for
- Platform device creation for SoundWire Manager instances and
PDM controller.
- SoundWire DMA driver.
- Interrupt handling for SoundWire manager related interrupts,
SoundWire DMA interrupts and ACP error interrupts.
- ACP PCI driver PM ops modification with respect to SoundWire
Power modes.
Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>:
Current soc-core.c has snd_soc_{of_}get_dai_name() to get DAI name
for dlc (snd_soc_dai_link_component). It gets .dai_name, but we need
.of_node too. Therefor user need to arrange.
It will be more useful if it gets both .dai_name and .of_node.
This patch adds snd_soc_{of_}get_dlc() for it, and convert to use it.
AMD SoundWire manager supports different power modes.
acp_reset flag will be set to false only when SoundWire manager power
mode is selected as ClockStop Mode. For rest of the combinations
(ACP PDM + SDW), acp_reset flag will be set to true.
When acp_reset flag is set, acp de-init and acp init sequence should
be invoked during suspend/resume callbacks.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230612095903.2113464-10-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move to request_threaded_irq and use thread for handling
SoundWire DMA interrupts.
Whenever audio data equal to the SoundWire FIFO watermark level
are produced/consumed, interrupt is generated.
Acknowledge the interrupt and wake up the irq thread.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230612095903.2113464-6-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SoundWire DMA platform driver binds to the platform device created by
ACP PCI device. SoundWire DMA driver registers ALSA DMA component
with ASoC framework.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230612095903.2113464-4-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Handle SoundWire manager related interrupts in ACP PCI driver
interrupt handler and schedule SoundWire manager work queue for
further processing.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230612095903.2113464-3-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on ACP pin configuration and scanning child devices
under ACP pci device ACPI scope, platform device configuration
(pdev_config) and platform device count(pdev_count) will be
calculated.
Using pdev_config and pdev_count values, ACP PCI driver will
create platform devices for Pink Sardine platform.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230612095903.2113464-2-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a spelling mistake in a dev_err message. Fix it. Also fix
grammar and add space between last word and (%d)".
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20230620095620.2522058-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Srinivas Kandagatla <srinivas.kandagatla@linaro.org>:
This patchset adds compressed offload support to Qualcomm audioreach drivers.
Currently it supports AAC, MP3 and FALC along with gapless.
Tested this on SM8450 and sc7280.
Merge series from Mark Brown <broonie@kernel.org>:
Several of the Everest Semi CODECs only support single register read and
write operations and therefore do not benefit from using the rbtree
cache over the maple tree cache, convert them to the more modern maple
tree cache.
Merge series from Mark Brown <broonie@kernel.org>:
Many of the Realtek I2C/SPI devices only support single register read
and write operations so don't benefit from using the rbtree cache
instead of the more modern maple tree cache, convert them to maple tree.
Current ASoC has snd_soc_{of_}get_dai_name() to get DAI name
for dlc (snd_soc_dai_link_component).
But we now can use snd_soc_{of_}get_dlc() for it. Let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87fs6mdgmc.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has snd_soc_{of_}get_dai_name() to get DAI name
for dlc (snd_soc_dai_link_component).
But we now can use snd_soc_{of_}get_dlc() for it. Let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87h6r2dgmi.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has snd_soc_{of_}get_dai_name() to get DAI name
for dlc (snd_soc_dai_link_component).
But we now can use snd_soc_{of_}get_dlc() for it. Let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87ilbidgmn.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has snd_soc_{of_}get_dai_name() to get DAI name
for dlc (snd_soc_dai_link_component).
But we now can use snd_soc_{of_}get_dlc() for it. Let's use it.
- note: need deep check
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87jzvydgms.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has snd_soc_{of_}get_dai_name() to get DAI name
for dlc (snd_soc_dai_link_component).
But we now can use snd_soc_{of_}get_dlc() for it. Let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87legedgmy.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ASoC has snd_soc_{of_}get_dai_name() to get DAI name
for dlc (snd_soc_dai_link_component).
But we now can use snd_soc_{of_}get_dlc() for it. Let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87mt0udgn3.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mastan Katragadda
Sameer Pujar
Sheetal
Vijendar Mukunda
Matthias Reichl
Mark Brown
Dan Carpenter
Arun Gopal Kondaveeti
Arnd Bergmann
Syed Saba Kareem
Maxim Kochetkov
Srinivas Kandagatla
Rob Herring
Fabio Estevam
Krzysztof Kozlowski
Mac Chiang
Terry Cheong
Colin Ian King
Kuninori Morimoto