The coldfire timer runs from 0 to TRR included, then 0 again and so on. It
counts thus actually TRR + 1 steps for 1 tick, not TRR. Fix that.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove regs arg from bad interrupt handler.
Use irq_handler_t type for handler arg of local request_irq().
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use irq_handler_t type for passing around timer interrupt routine
in 368360 setup code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use irq_handler_t type for passing around timer interrupt routine.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
powerpc gets:
init/main.c: In function `do_basic_setup':
init/main.c:714: warning: implicit declaration of function `init_irq_proc'
but we cannot include linux/irq.h in generic code.
Fix it by moving the declaration into linux/interrupt.h instead.
And make sure all code that defines init_irq_proc() is including
linux/interrupt.h.
And nuke an ifdef-in-C
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correct mis-spellings of "algorithm", "appear", "consistent" and
(shame, shame) "kernel".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Use irq_handler_t type for passing timer handler to timer init code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds support for RTCs (through genrtc) for M68KNOMMU.
Board-specific code will have to link the appropriate RTC driver to the
mach_hwclk callback, at minimum.
This patch switches the 68360 code over to using rtc_time.
Signed-off-by: Gavin Lambert <gavinl@compacsort.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 523x timer TRR register is a full 32bits, the older register (on
other ColdFire parts) was only 16 bits. Use the right type of
__raw_read when accessing it.
Problem found by Yaroslav Vinogradov <yaroslav.vinogradov@freescale.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove use of __rom_end symbol all together. This helps clean out the
miscellaneous symbols lying around in the m68knommu linker script.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here is a small patch to automatically detect the DRAM size on m520x.
It was generated against 2.6.17-uc0, and tested on an Intec 5208 dev board.
Signed-off-by: Michael Broughton <mbobowik@telusplanet.net>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Switch to using irq_handler_t for interrupt function handler pointers.
Change name of m68knommu's irq_hanlder_t data structure so it doesn't
clash with the common type (include/linux/interrupt.h).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Use the new IRQF_ constants and remove the SA_INTERRUPT define
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix 68EZ328/config.c asm to be clean for new gcc versions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix 68VZ328/config.c asm to be clean for new gcc versions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix 68360/config.c asm to be clean for new gcc versions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The irqnode_t struct has moved to irqnode.h, need to include that
68360 ints.c.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conditionaly compile the 68328 romvec code based on the ROM configuration
being enabled.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the inline 68328 romvec section asm code into its own file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Create the 68328 romvec section in its own assembler file. It can be
compiled in when required.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Switch to using the new RAM Kconfig settings, instead of linker defined
regions in ROM specific 68328 startup code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Switch to using the new RAM Kconfig settings, instead of linker defined
regions in ROM specific 68360 startup code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Switch to using the new RAM Kconfig settings, instead of linker defined
regions in RAM specific 68360 startup code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change to using a configurable RAM setup in startup code. This cleans up
the whole RAM base/sizing issue, and removes a lot of board specific code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean out unused variable definitions from 68328 start up code.
Also use a more appropriate start address for the case of relocating
the kernel code to RAM (from ROM/flash).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
__ramvec has been removed from the linker script. The vector base
address is defined as a configurable option, use that. Remove its
use from the 68328/pilot startup code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here is a patch to the system call handling for 5307/5272/etc to:
- fix the strace support (one tested the wrong bit)
- make all system calls a little bit faster by inlining set_esp0 and
supporting ENOSYS out of the critical path.
- remove extraneous spaces
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add build support for the new Freescale 532x CPU platforms.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add build support for new Freescale M532x CPU family timer.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add kernel startup code for the new Freescale 532x CPU family.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modify the m68knommu/ColdFire PIT timer code to use register offsets
with raw_read/raw_write access, instead of a mapped struct.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modify the m68knommu/ColdFire core timer code to use register offsets
with raw_read/raw_write access, instead of a mapped struct.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move some of the m68knommu platform specific irq core support
to its own header, irqnode.h. Having it in asm-m68knommu/irq.h
causes some build pain, since it is included in a number of
common code places (and not all the required definitions will
be included at these places).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Freescale M5208EVB ColdFire eval board is one of the few that
doesn't have its DRAM based at address 0. Handle this special case
in the common ColdFire startup code.
Patch originally from Matt Waddel.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modified common ColdFire PIT timer code to support the 5208 as well.
It uses a different set of mask and interrupt bits than other ColdFire
processors. The defines for these bits have been moved in header
files and set appropriately for the different processor varients.
Patch originally from Matt Waddel.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Platform configuration code for the Freescale 5208 ColdFire processor.
Patch originally from Matt Waddel (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Freescale 5208 ColdFire uses the common PIT timer code for
its internal timer. Build it when configured for the 5208 processor.
Add support for the internal register map of the 5208 ColdFire fmaily.
Patch originally from Matt Waddel (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add Freescale 5208 ColdFire platform Makefile.
Patch originally from Matt Waddel (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Specialized startup code for the 68328 based DragenEngine board.
It doesn't easily fit into the common 68x328 startup code framework.
It doesn't want any of the common hardware setup to be done here.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Create common start code for all 68360 based platforms that are
loaded and run directly from RAM (as opposed to running from
flash/ROM). This replaces the old specific startup code for
each board.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Create common start code for all 68360 based platforms that are
loaded and run directly from ROM/flash (as opposed to running from
RAM). This replaces the old specific startup code for each board.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rework the 68x328 configuration and setup code. All 68x328 varients
share the same timer hardware. So extract that into its own file,
instead of keeping copies in each processors setup code.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The boot loader on the MOD5272 board doesn't set the register maping,
so set it in the 5272 init code. There was code in there to support
this, but we had never needed to use it before.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Greg Ungerer
Andrew Morton
Robert P. J. Day
Michael Broughton
Dave Jones
Uwe Zeisberger
Thomas Gleixner
Jörn Engel
Philippe De Muyter