This one was left behind by a previous cleanup patch:
drivers/gpio/gpio-ep93xx.c: In function 'ep93xx_gpio_add_bank':
drivers/gpio/gpio-ep93xx.c:366:34: error: unused variable 'ic' [-Werror=unused-variable]
Fixes: 216f37366e ("gpio: ep93xx: Make irqchip immutable")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Fix wrong translation of irq numbers in port F handler, as ep93xx hwirqs
increased by 1, we should simply decrease them by 1 in translation.
Fixes: 482c27273f ("ARM: ep93xx: renumber interrupts")
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
We recently added locking to this function but one error path was
over looked. Drop the lock before returning.
Fixes: e546427762 ("gpio: mxc: Protect GPIO irqchip RMW with bgpio spinlock")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
commit 1796f808e4 ("HID: i2c-hid: acpi: Stop setting wakeup_capable")
adjusted the policy to enable wakeup by default if the ACPI tables
indicated that a device was wake capable.
It was reported however that this broke suspend on at least two System76
systems in S3 mode and two Lenovo Gen2a systems, but only with S3.
When the machines are set to s2idle, wakeup behaves properly.
Configuring the GPIOs for wakeup with S3 doesn't work properly, so only
set it when the system supports low power idle.
Fixes: 1796f808e4 ("HID: i2c-hid: acpi: Stop setting wakeup_capable")
Fixes: b38f2d5d96 ("i2c: acpi: Use ACPI wake capability bit to set wake_irq")
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2357
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2162013
Reported-by: Nathan Smythe <ncsmythe@scruboak.org>
Tested-by: Nathan Smythe <ncsmythe@scruboak.org>
Suggested-by: Raul Rangel <rrangel@chromium.org>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
commit 1796f808e4 ("HID: i2c-hid: acpi: Stop setting wakeup_capable")
changed the policy such that I2C touchpads may be able to wake up the
system by default if the system is configured as such.
However on Clevo NL5xRU there is a mistake in the ACPI tables that the
TP_ATTN# signal connected to GPIO 9 is configured as ActiveLow and level
triggered but connected to a pull up. As soon as the system suspends the
touchpad loses power and then the system wakes up.
To avoid this problem, introduce a quirk for this model that will prevent
the wakeup capability for being set for GPIO 9.
Fixes: 1796f808e4 ("HID: i2c-hid: acpi: Stop setting wakeup_capable")
Reported-by: Werner Sembach <wse@tuxedocomputers.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1722#note_1720627
Co-developed-by: Werner Sembach <wse@tuxedocomputers.com>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Using the `ignore_wake` quirk or module parameter doesn't work for any pin
that has been specified in the _CRS instead of _AEI.
Extend the `acpi_gpio_irq_is_wake` check to cover both places.
Suggested-by: Raul Rangel <rrangel@chromium.org>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1722#note_1722335
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Always configure GPIO pins which are used as interrupt source as INPUTs.
In case the default pin configuration is OUTPUT, or the prior stage does
configure the pins as OUTPUT, then Linux will not reconfigure the pin as
INPUT and no interrupts are received.
Always configure the interrupt source GPIO pin as input to fix the above case.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 07bd1a6cc7 ("MXC arch: Add gpio support for the whole platform")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The driver currently performs register read-modify-write without locking
in its irqchip part, this could lead to a race condition when configuring
interrupt mode setting. Add the missing bgpio spinlock lock/unlock around
the register read-modify-write.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Fixes: 07bd1a6cc7 ("MXC arch: Add gpio support for the whole platform")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 96868dce64 ("gpio/sifive: Add GPIO driver for SiFive SoCs")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Make the struct irq_chip const, flag it as IRQCHIP_IMMUTABLE, add the
new helper functions, and call the appropriate gpiolib functions.
Signed-off-by: Cixi Geng <cixi.geng1@unisoc.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Remove the irq_chip from pmic_eic structure,
use the various calls by defining the statically
irq_chip structure.
Signed-off-by: Cixi Geng <cixi.geng1@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Remove the irq_chip from pmic_eic structure,
use the various calls by defining the statically
irq_chip structure.
Signed-off-by: Cixi Geng <cixi.geng1@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
There is a variable pinctrl declared without initializer. And then
has the case (switch operation chose the default case) to directly
use this uninitialized value, this is not a safe behavior. So here
initialize the pinctrl as 0 to avoid this issue.
This is reported by Coverity.
Fixes: 13c5d4ce80 ("gpio: pca953x: Add support for PCAL6534")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Commit 8eb1f71e7a ("gpiolib: consolidate GPIO lookups") refactors
fwnode_get_named_gpiod() and gpiod_get_index() into a unified
gpiod_find_and_request() helper.
The old functions both initialized their local lookupflags variable to
GPIO_LOOKUP_FLAGS_DEFAULT, but the new code leaves it uninitialized.
This is a problem for at least ACPI platforms, where acpi_find_gpio()
only does a bunch of *lookupflags |= GPIO_* statements and thus relies
on the variable being initialized.
The variable not being initialized leads to:
1. Potentially the wrong flags getting used
2. The check for conflicting lookup flags in gpiod_configure_flags():
"multiple pull-up, pull-down or pull-disable enabled, invalid config"
sometimes triggering, making the GPIO unavailable
Restore the initialization of lookupflags to GPIO_LOOKUP_FLAGS_DEFAULT
to fix this.
Fixes: 8eb1f71e7a ("gpiolib: consolidate GPIO lookups")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Various changes across the board, mostly improvements and cleanups.
-----BEGIN PGP SIGNATURE-----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=IM51
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Various changes across the board, mostly improvements and cleanups"
* tag 'pwm/for-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (42 commits)
pwm: pca9685: Convert to i2c's .probe_new()
pwm: sun4i: Propagate errors in .get_state() to the caller
pwm: Handle .get_state() failures
pwm: sprd: Propagate errors in .get_state() to the caller
pwm: rockchip: Propagate errors in .get_state() to the caller
pwm: mtk-disp: Propagate errors in .get_state() to the caller
pwm: imx27: Propagate errors in .get_state() to the caller
pwm: cros-ec: Propagate errors in .get_state() to the caller
pwm: crc: Propagate errors in .get_state() to the caller
leds: qcom-lpg: Propagate errors in .get_state() to the caller
drm/bridge: ti-sn65dsi86: Propagate errors in .get_state() to the caller
pwm/tracing: Also record trace events for failed API calls
pwm: Make .get_state() callback return an error code
pwm: pxa: Enable for MMP platform
pwm: pxa: Add reference manual link and limitations
pwm: pxa: Use abrupt shutdown mode
pwm: pxa: Remove clk enable/disable from pxa_pwm_config
pwm: pxa: Set duty cycle to 0 when disabling PWM
pwm: pxa: Remove pxa_pwm_enable/disable
pwm: mediatek: Add support for MT7986
...
GPIO core:
- teach gpiolib to work with software nodes for HW description
- remove ARCH_NR_GPIOS treewide as we no longer impose any limit on the number
of GPIOS since the allocation became entirely dynamic
- add support for HW quirks for Cirrus CS42L56 codec, Marvell NFC controller,
Freescale PCIe and Ethernet controller, Himax LCDs and Mediatek mt2701
- refactor OF quirk code
- some general refactoring of the OF and ACPI code, adding new helpers, minor
tweaks and fixes, making fwnode usage consistent etc.
GPIO uAPI:
- fix an issue where the user-space can trigger a NULL-pointer dereference in
the kernel by opening a device file, forcing a driver unbind and then calling
one of the syscalls on the associated file descriptor
New drivers:
- add gpio-latch: a new GPIO multiplexer based on latches connected to other
GPIOs
Driver updates:
- convert i2c GPIO expanders to using .probe_new()
- drop the gpio-sta2x11 driver
- factor out common code for the ACCES IDIO-16 family of controllers and use
this new library wherever applicable in drivers
- add DT support to gpio-hisi
- allow building gpio-davinci as a module and increase its maxItems property
- add support for a new model to gpio-pca9570
- other minor changes to various drivers
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEFp3rbAvDxGAT0sefEacuoBRx13IFAmObAGkACgkQEacuoBRx
13Jrew//VWgqyLgfOysJ5hdVQigY3KGEPbai2nXQK58HFymdBer2MG/G27j0aw46
mEgwYcrDKO4fi08AzCXexF/JYFZha7s4EwujJ/uRmye7xtVgs1xlaPPhTtFV2Iky
P2994k1IhsScou5Tu9WZmHyeGLhiMleuBe+KbL4Xhfa1JYUhQymiQi8aiBGs7fW3
aMTtTa/7NpDl3YFNS+un7Ahuftj1CfwGYOiWeQy+Fy1UE5uE/UgvmiSYi/3rvrCQ
O/WVWgd26sTKyGb92nrbHjY2DPr5ULAC8aRY3JQ1pmfyPpTuqNUtb+CUYjP/oxqx
JjZms96YW7B7sL93SNWog+9ZyYr+jnfdg+ZgGDEZ1ViGXgoe/Fr+xs6tRwww8GL4
Bt3nAlAR/X2Udarlmep4Udca5BOr2kc7JmcVEvNrVJAI7wGxo3SKWdIWcgs43e0B
Ps3iJmdK4ndzHh4jrcZEzZUXpmOSHzpiW/YuqPd/9XNpJowhT2BObukRlAcVZqjf
PvyN2nktF45fqjuszBo0GK9QZv0DUofgkUxYgEpdIvLwfvodJVoFbK5KOI0Kqxfc
CJxuAgKgEI569iEguEj7+pF5c1VW5LWJRV2kG6XbxwXKn2c+47/HkvvrR34sLu9n
+7yp4x5BflVQiQsrbDfQiYXOz8jb8tWgn1o1LIQyYkUan4zCjjk=
=zg1O
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We have a new GPIO multiplexer driver, bunch of driver updates and
refactoring in the core GPIO library.
GPIO core:
- teach gpiolib to work with software nodes for HW description
- remove ARCH_NR_GPIOS treewide as we no longer impose any limit on
the number of GPIOS since the allocation became entirely dynamic
- add support for HW quirks for Cirrus CS42L56 codec, Marvell NFC
controller, Freescale PCIe and Ethernet controller, Himax LCDs and
Mediatek mt2701
- refactor OF quirk code
- some general refactoring of the OF and ACPI code, adding new
helpers, minor tweaks and fixes, making fwnode usage consistent
etc.
GPIO uAPI:
- fix an issue where the user-space can trigger a NULL-pointer
dereference in the kernel by opening a device file, forcing a
driver unbind and then calling one of the syscalls on the
associated file descriptor
New drivers:
- add gpio-latch: a new GPIO multiplexer based on latches connected
to other GPIOs
Driver updates:
- convert i2c GPIO expanders to using .probe_new()
- drop the gpio-sta2x11 driver
- factor out common code for the ACCES IDIO-16 family of controllers
and use this new library wherever applicable in drivers
- add DT support to gpio-hisi
- allow building gpio-davinci as a module and increase its maxItems
property
- add support for a new model to gpio-pca9570
- other minor changes to various drivers"
* tag 'gpio-updates-for-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (66 commits)
gpio: sim: set a limit on the number of GPIOs
gpiolib: protect the GPIO device against being dropped while in use by user-space
gpiolib: cdev: fix NULL-pointer dereferences
gpiolib: Provide to_gpio_device() helper
gpiolib: Unify access to the device properties
gpio: Do not include <linux/kernel.h> when not really needed.
gpio: pcf857x: Convert to i2c's .probe_new()
gpio: pca953x: Convert to i2c's .probe_new()
gpio: max732x: Convert to i2c's .probe_new()
dt-bindings: gpio: gpio-davinci: Increase maxItems in gpio-line-names
gpiolib: ensure that fwnode is properly set
gpio: sl28cpld: Replace irqchip mask_invert with unmask_base
gpiolib: of: Use correct fwnode for DT-probed chips
gpiolib: of: Drop redundant check in of_mm_gpiochip_remove()
gpiolib: of: Prepare of_mm_gpiochip_add_data() for fwnode
gpiolib: add support for software nodes
gpiolib: consolidate GPIO lookups
gpiolib: acpi: avoid leaking ACPI details into upper gpiolib layers
gpiolib: acpi: teach acpi_find_gpio() to handle data-only nodes
gpiolib: acpi: change acpi_find_gpio() to accept firmware node
...
With the removal of ARCH_NR_GPIOS in commit 7b61212f2a ("gpiolib: Get
rid of ARCH_NR_GPIOS") the gpiolib core no longer sanitizes the number
of GPIOs for us. This causes the gpio-sim selftests to now fail when
setting the number of GPIOs to 99999 and expecting the probe() to fail.
Set a sane limit of 1024 on the number of simulated GPIOs and bail out
of probe if it's exceeded.
Reported-by: kernel test robot <oliver.sang@intel.com>
Link: https://lore.kernel.org/oe-lkp/202212112236.756f5db9-oliver.sang@intel.com
Fixes: 7b61212f2a ("gpiolib: Get rid of ARCH_NR_GPIOS")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Core changes:
- Minor but nice and important documentation clean-ups.
New drivers:
- New subdriver for the Qualcomm SDM670 SoC.
- New subdriver for the Intel Moorefield SoC.
- New trivial support for the NXP Freescale i.MXRT1170 SoC.
Other changes and improvements
- A major clean-up of the Qualcomm pin control device tree bindings
by Krzysztof.
- A major header clean-up by Andy.
- Some immutable irqchip clean-up for the Actions Semiconductor
and Nuvoton drivers.
- GPIO helpers for The Cypress cy8c95x0 driver.
- Bias handling in the Mediatek MT7986 driver.
- Remove the unused pins-are-numbered concept that never flew.
-----BEGIN PGP SIGNATURE-----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=PhTP
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"The two large chunks is the header clean-up from Andy and the Qualcomm
DT bindings clean-up from Krzysztof. Each which could give rise to
conflicts, but I haven't seen any.
The YAML conversions happening around the device tree is the biggest
item in the series and is the result of Rob Herrings ambition to
autovalidate these trees against strict schemas and it is paying off
in lots of bugs found and ever prettier device trees. Sooner or later
the transition will be complete, Krzysztof is fixing up all of the
Qualcomm stuff, which is pretty voluminous.
Core changes:
- minor but nice and important documentation clean-ups
New drivers:
- subdriver for the Qualcomm SDM670 SoC
- subdriver for the Intel Moorefield SoC
- trivial support for the NXP Freescale i.MXRT1170 SoC
Other changes and improvements
- major clean-up of the Qualcomm pin control device tree bindings by
Krzysztof
- major header clean-up by Andy
- some immutable irqchip clean-up for the Actions Semiconductor and
Nuvoton drivers
- GPIO helpers for The Cypress cy8c95x0 driver
- bias handling in the Mediatek MT7986 driver
- remove the unused pins-are-numbered concept that never flew"
* tag 'pinctrl-v6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (231 commits)
pinctrl: thunderbay: fix possible memory leak in thunderbay_build_functions()
dt-bindings: pinctrl: st,stm32: Deprecate pins-are-numbered
dt-bindings: pinctrl: mediatek,mt65xx: Deprecate pins-are-numbered
pinctrl: stm32: Remove check for pins-are-numbered
pinctrl: mediatek: common: Remove check for pins-are-numbered
pinctrl: qcom: remove duplicate included header files
pinctrl: sunxi: d1: Add CAN bus pinmuxes
pinctrl: loongson2: Fix some const correctness
pinctrl: pinconf-generic: add missing of_node_put()
pinctrl: intel: Enumerate PWM device when community has a capability
pwm: lpss: Rename pwm_lpss_probe() --> devm_pwm_lpss_probe()
pwm: lpss: Allow other drivers to enable PWM LPSS
pwm: lpss: Include headers we are the direct user of
pwm: lpss: Rename MAX_PWMS --> LPSS_MAX_PWMS
pwm: Add a stub for devm_pwmchip_add()
pinctrl: k210: call of_node_put()
pinctrl: starfive: Use existing variable gpio
dt-bindings: pinctrl: semtech,sx150xq: fix match patterns for 16 GPIOs matching
pinconf-generic: fix style issues in pin_config_param doc
pinctrl: pinctrl-loongson2: fix Kconfig dependency
...
While any of the GPIO cdev syscalls is in progress, the kernel can call
gpiochip_remove() (for instance, when a USB GPIO expander is disconnected)
which will set gdev->chip to NULL after which any subsequent access will
cause a crash.
To avoid that: use an RW-semaphore in which the syscalls take it for
reading (so that we don't needlessly prohibit the user-space from calling
syscalls simultaneously) while gpiochip_remove() takes it for writing so
that it can only happen once all syscalls return.
Fixes: d7c51b47ac ("gpio: userspace ABI for reading/writing GPIO lines")
Fixes: 3c0d9c635a ("gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL")
Fixes: aad955842d ("gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL")
Fixes: a54756cb24 ("gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL")
Fixes: 7b8e00d981 ("gpiolib: cdev: support GPIO_V2_LINE_SET_VALUES_IOCTL")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
[Nick: fixed a build failure with CDEV_V1 disabled]
Co-authored-by: Nick Hainke <vincent@systemli.org>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
There are several places where we can crash the kernel by requesting
lines, unbinding the GPIO device, then calling any of the system calls
relevant to the GPIO character device's annonymous file descriptors:
ioctl(), read(), poll().
While I observed it with the GPIO simulator, it will also happen for any
of the GPIO devices that can be hot-unplugged - for instance any HID GPIO
expander (e.g. CP2112).
This affects both v1 and v2 uAPI.
This fixes it partially by checking if gdev->chip is not NULL but it
doesn't entirely remedy the situation as we still have a race condition
in which another thread can remove the device after the check.
Fixes: d7c51b47ac ("gpio: userspace ABI for reading/writing GPIO lines")
Fixes: 3c0d9c635a ("gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL")
Fixes: aad955842d ("gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL")
Fixes: a54756cb24 ("gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL")
Fixes: 7b8e00d981 ("gpiolib: cdev: support GPIO_V2_LINE_SET_VALUES_IOCTL")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
.get_state() might fail in some cases. To make it possible that a driver
signals such a failure change the prototype of .get_state() to return an
error code.
This patch was created using coccinelle and the following semantic patch:
@p1@
identifier getstatefunc;
identifier driver;
@@
struct pwm_ops driver = {
...,
.get_state = getstatefunc
,...
};
@p2@
identifier p1.getstatefunc;
identifier chip, pwm, state;
@@
-void
+int
getstatefunc(struct pwm_chip *chip, struct pwm_device *pwm, struct pwm_state *state)
{
...
- return;
+ return 0;
...
}
plus the actual change of the prototype in include/linux/pwm.h (plus some
manual fixing of indentions and empty lines).
So for now all drivers return success unconditionally. They are adapted
in the following patches to make the changes easier reviewable.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221130152148.2769768-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The node returned by of_get_parent() with refcount incremented,
of_node_put() needs be called when finish using it. So add it in the
end of of_pinctrl_get().
Fixes: 936ee2675e ("gpio/rockchip: add driver for rockchip gpio")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() after the 'out' label. Since pci_dev_put() can handle NULL
input parameter, there is no problem for the 'Device not found' branch.
For the normal path, add pci_dev_put() in amd_gpio_exit().
Fixes: f942a7de04 ("gpio: add a driver for GPIO pins found on AMD-8111 south bridge chips")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Provide to_gpio_device() helper which can be utilized in the existing
and future code.
While at it, make sure it becomes no-op at compilation time.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Some of the functions are using struct fwnode_handle, some struct device
pointer. In the GPIO library the firmware node of the GPIO device is the
same as GPIO node of the GPIO chip. Due to this fact we may use former
to access properties everywhere in the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Tested-by: Marijn Suijten <marijn.suijten@somainline.org>
[Bartosz: stick to the 80-char limit where it's not hurting readability]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Here is a backtrace report about memory leak detected in
gpiochip_setup_dev():
unreferenced object 0xffff88810b406400 (size 512):
comm "python3", pid 1682, jiffies 4295346908 (age 24.090s)
backtrace:
kmalloc_trace
device_add device_private_init at drivers/base/core.c:3361
(inlined by) device_add at drivers/base/core.c:3411
cdev_device_add
gpiolib_cdev_register
gpiochip_setup_dev
gpiochip_add_data_with_key
gcdev_register() & gcdev_unregister() would call device_add() &
device_del() (no matter CONFIG_GPIO_CDEV is enabled or not) to
register/unregister device.
However, if device_add() succeeds, some resource (like
struct device_private allocated by device_private_init())
is not released by device_del().
Therefore, after device_add() succeeds by gcdev_register(), it
needs to call put_device() to release resource in the error handle
path.
Here we move forward the register of release function, and let it
release every piece of resource by put_device() instead of kfree().
While at it, fix another subtle issue, i.e. when gc->ngpio is equal
to 0, we still call kcalloc() and, in case of further error, kfree()
on the ZERO_PTR pointer, which is not NULL. It's not a bug per se,
but rather waste of the resources and potentially wrong expectation
about contents of the gdev->descs variable.
Fixes: 159f3cd92f ("gpiolib: Defer gpio device setup until after gpiolib initialization")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
* Miscellaneous updates to the core (cdev, acpi) and Intel Merrifield driver
The following is an automated git shortlog grouped by driver:
gpiolib:
- cdev: Fix typo in kernel doc for struct line
- acpi: Use METHOD_NAME__AEI macro for acpi_walk_resources
merrifield:
- Use str_enable_disable() helper
-----BEGIN PGP SIGNATURE-----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=/a32
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into gpio/for-next
intel-gpio for v6.2-1
* Miscellaneous updates to the core (cdev, acpi) and Intel Merrifield driver
The following is an automated git shortlog grouped by driver:
gpiolib:
- cdev: Fix typo in kernel doc for struct line
- acpi: Use METHOD_NAME__AEI macro for acpi_walk_resources
merrifield:
- Use str_enable_disable() helper
Note that this is a RFC patch and not meant to be merged. I looked into
a problem with linux-next-20221110 on the Qualcomm SA8540P automotive
board (sc8280xp) where the UFS host controller would fail to probe due
to repeated probe deferrals when trying to get reset-gpios via
devm_gpiod_get_optional().
of_get_named_gpiod_flags() returns -EPROBE_DEFER, which is caused by
of_gpiochip_match_node_and_xlate() returning 0 since the of_xlate function
pointer is not set for the qcom,sc8280xp-tlmm pinctrl driver. The
pinctrl driver doesn't define one, so of_gpiochip_add() should
automatically setup of_gpio_simple_xlate() on it's behalf. This doesn't
happen since the fwnode member on the struct gpiochip is set to null
when of_gpiochip_add() is called. Let's work around this by ensuring
that it's set if available.
Note that this broke sometime within the last few weeks within
linux-next and I haven't bisected this. I'm posting this in the hopes
that someone may know offhand which patch(es) may have broken this.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Tested-by: Marijn Suijten <marijn.suijten@somainline.org>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org> #Lenovo Thinkpad X13s
Tested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Remove use of the deprecated mask_invert flag. Inverted mask
registers (where a '1' bit enables an IRQ) can be described more
directly as an unmask register.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The OF node store in chip->fwnode is used to explicitly override the FW
node for a GPIO chip. For chips that use the default FW node (i.e. that
of their parent device), this will be NULL and cause the chip not to be
fully registered.
Instead, use the GPIO device's FW node, which is set to either the node
of the parent device or the explicit override in chip->fwnode.
Fixes: 8afe825502 ("gpiolib: of: Prepare of_gpiochip_add() / of_gpiochip_remove() for fwnode")
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Robert Marko <robimarko@gmail.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Tested-by: Brian Masney <bmasney@redhat.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The callers never call the function with invalid pointer.
Moreover, compiler quite likely dropped that check anyway
because we use that pointer before the check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Now that static device properties understand notion of child nodes and
references, let's teach gpiolib to handle them:
- GPIOs are represented as a references to software nodes representing
gpiochip
- references must have 2 arguments - GPIO number within the chip and
GPIO flags (GPIO_ACTIVE_LOW/GPIO_ACTIVE_HIGH, etc)
- a new PROPERTY_ENTRY_GPIO() macro is supplied to ensure the above
- name of the software node representing gpiochip must match label of
the gpiochip, as we use it to locate gpiochip structure at runtime
The following illustrates use of software nodes to describe a "System"
button that is currently specified via use of gpio_keys_platform_data
in arch/mips/alchemy/board-mtx1.c. It follows bindings specified in
Documentation/devicetree/bindings/input/gpio-keys.yaml.
static const struct software_node mxt1_gpiochip2_node = {
.name = "alchemy-gpio2",
};
static const struct property_entry mtx1_gpio_button_props[] = {
PROPERTY_ENTRY_U32("linux,code", BTN_0),
PROPERTY_ENTRY_STRING("label", "System button"),
PROPERTY_ENTRY_GPIO("gpios", &mxt1_gpiochip2_node, 7, GPIO_ACTIVE_LOW),
{ }
};
Similarly, arch/arm/mach-tegra/board-paz00.c can be converted to:
static const struct software_node tegra_gpiochip_node = {
.name = "tegra-gpio",
};
static struct property_entry wifi_rfkill_prop[] __initdata = {
PROPERTY_ENTRY_STRING("name", "wifi_rfkill"),
PROPERTY_ENTRY_STRING("type", "wlan"),
PROPERTY_ENTRY_GPIO("reset-gpios",
&tegra_gpiochip_node, 25, GPIO_ACTIVE_HIGH);
PROPERTY_ENTRY_GPIO("shutdown-gpios",
&tegra_gpiochip_node, 85, GPIO_ACTIVE_HIGH);
{ },
};
static struct platform_device wifi_rfkill_device = {
.name = "rfkill_gpio",
.id = -1,
};
...
software_node_register(&tegra_gpiochip_node);
device_create_managed_software_node(&wifi_rfkill_device.dev,
wifi_rfkill_prop, NULL);
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Ensure that all paths to obtain/look up GPIOD from generic
consumer-visible APIs go through the new gpiod_find_and_request()
helper, so that we can easily extend it with support for new firmware
mechanisms.
The only exception is OF-specific [devm_]gpiod_get_from_of_node() API
that is still being used by a couple of drivers and will be removed as
soon as patches converting them to use generic fwnode/device APIs are
accepted.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
There is no need for the generic parts of GPIOLIB to be aware of
implementation details of ACPI-bases lookups.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
In preparation of switching all ACPI-based GPIO lookups to go through
acpi_find_gpio() we need to make sure it can handle data-only ACPI
nodes, same as existing acpi_node_get_gpiod().
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
In preparation of switching all ACPI-based GPIO lookups to go through
acpi_find_gpio() let's change it to accept device node as its argument
as we do not always have access to device structure.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
In preparation of switching all OF-based GPIO lookups to go through
of_find_gpio() let's change it to accept device node as its argument as
we do not always have access to device structure.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Added module build support for the davinci gpio driver
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Nicolas Frayer <nfrayer@baylibre.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
On i.MX8QM/QXP/DXL SoCs, even a GPIO is selected as the wakeup source,
the GPIO block will be powered off when system enters into suspend
state. This can greatly reduce the power consumption of suspend state
because the whole partition can be shutdown. This is called PAD wakeup
feature on i.MX8x platform.
This patch adds the noirq suspend/resume hooks and uses the pad wakeup
feature as the default wakeup method for GPIO modules on
i.MX8QM/QXP/DXL platforms.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20221027130859.1444412-6-shenwei.wang@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for HiSilicon GPIO controller in embedded platform, which
boot from devicetree.
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Acked-by: Jay Fang <f.fangjian@huawei.com>
Reviewed-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
It's actually preferable to use Generic regmap GPIO over other
simple approaches. Add a TODO item for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Bindings for Freescale PCIe controller use a separate property called
"reset-gpio-active-high" to control polarity of its reset line, add it
to the list of quirks in gpiolib so that gpiod API can be used in the
driver.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Several legacy bindings use a separate property to specify polarity of
GPIOs instead of specifying it directly in the GPIO property. Factor
out this code to make it easier to add more such cases.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>