The Lantiq family of SoCs have a EBU (External Bus Unit). This patch adds
the driver that allows us to use the EBU as a PCI controller. In order for
PCI to work the EBU is set to endianess swap all the data. In addition we
need to make use of SWAP_IO_SPACE for device->host DMA to work.
The clock of the PCI works in several modes (internal/external). If this
is not configured correctly the SoC will hang.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2250/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the Lantiq XWAY family of Mips24KEc SoCs.
* Danube (PSB50702)
* Twinpass (PSB4000)
* AR9 (PSB50802)
* Amazon SE (PSB5061)
The Amazon SE is a lightweight SoC and has no PCI as well as a different
clock. We split the code out into seperate files to handle this.
The GPIO pins on the SoCs are multi function and there are several bits
we can use to configure the pins. To be as compatible as possible to
GPIOLIB we add a function
int lq_gpio_request(unsigned int pin, unsigned int alt0,
unsigned int alt1, unsigned int dir, const char *name);
which lets you configure the 2 "alternate function" bits. This way drivers like
PCI can make use of GPIOLIB without a cubersome wrapper.
The PLL code inside arch/mips/lantiq/xway/clk-xway.c is voodoo to me. It was
taken from a 2.4.20 source tree and was never really changed by me since then.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2249/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add initial support for Mips based SoCs made by Lantiq. This series will add
support for the XWAY family.
The series allows booting a minimal system using a initramfs or NOR. Missing
drivers and support for Amazon and GPON family will be provided in a later
series.
[Ralf: Remove some cargo cult programming and fixed formatting.]
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2252/
Patchwork: https://patchwork.linux-mips.org/patch/2371/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Adds pci/pci-xlr.c to support for XLR PCI/PCI-X interface and XLS PCIe
interface.
Update irq.c to ack PCI interrupts, use irq handler data to do the
PCI/PCIe bus ack.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2337/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Enable XLR CPU support, SMP, initramfs based root filesystem etc.
[ralf@linux-mips.org: shrink the defconfig file through make savedefconfig.]
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add NLM_XLR_BOARD, CPU_XLR and other config options
Makefile updates, mostly based on r4k
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2334/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* include/asm/netlogic added with files common for all Netlogic processors
(common with XLP which will be added later)
* include/asm/netlogic/xlr for XLR/XLS chip specific files
* netlogic/xlr for XLR/XLS platform files
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2334/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CPU_XLR case added to mm/tlbex.c
CPU_XLR case added to mm/c-r4k.c for PINDEX attribute
Feature overrides for XLR cpu.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2333/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add Netlogic Microsystems company ID and processor IDs for XLR
and XLS processors for CPU probe. Add CPU_XLR to cpu_type_enum.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2367/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It seems that Adrian is getting old. He removed almost everything of
GEMINI in commit c53653130 ("[POWERPC] Remove the broken Gemini
support") except this piece.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[See http://lists.ozlabs.org/pipermail/linuxppc-dev/2010-October/086424.html
and followups. Part of the commit message is directly copied from that.]
Commit 540c6c392f tries to find i8042 IRQs in
the device-tree but doesn't fall back to the old hardcoded 1 and 12 in all
failure cases.
Specifically, the case where the device-tree contains nothing matching
pnpPNP,303 or pnpPNP,f03 doesn't seem to be handled well. It sort of falls
through to the old code, but leaves the IRQs set to 0.
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We keep track of the size of the lowest block of memory and call
setup_initial_memory_limit() only after we've parsed them all
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Milton Miller <miltonm@bga.com>
When using a property refering to the availibily of dynamic dma windows
call it ddw_avail not ddr_avail.
dupe_ddw_if_already_created does not dupilcate anything, it only finds
and reuses the windows we already created, so rename it to
find_existing_ddw. Also, it does not need the pci device node, so
remove that argument.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move the discovery of windows previously setup from when the pci driver
calls set_dma_mask to an arch_initcall.
When kexecing into a kernel with dynamic dma windows allocated, we need
to find the windows early so that memory hot remove will be able to
delete the tces mapping the to be removed memory and memory hotplug add
will map the new memory into the window. We should not wait for the
driver to be loaded and the device to be probed. The iommu init hooks
are before kmalloc is setup, so defer to arch_initcall.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we destroy the window, we need to remove the property recording that
we setup the window. Otherwise the next kernel we kexec will be
confused.
Also we should remove the property if even if we don't find the
ibm,ddw-applicable window or if one of the property sizes is unexpected;
presumably these came from a prior kernel via kexec, and we will not be
maintaining the window with respect to memory hotplug.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Do not check dma supported until we have chosen the right dma ops.
Check that the device is pci before treating it as such.
Check the mask is supported by the selected dma ops before
committing it.
We only need to set iommu ops if it is not the current ops; this
avoids searching the tree for the iommu table unnecessarily.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Otherwise we get silent truncations.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Milton Miller <miltonm@bga.com>
Cc: linuxppc-dev@ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While debugging I stumbled over two problems in the code that protects module
pages.
First issue is that disabling the protection before freeing init or unload of
a module is not symmetric with the enablement. For instance, if pages are set
to RO the page range from module_core to module_core + core_ro_size is
protected. If a module is unloaded the page range from module_core to
module_core + core_size is set back to RW.
So pages that were not set to RO are also changed to RW.
This is not critical but IMHO it should be symmetric.
Second issue is that while set_memory_rw & set_memory_ro are used for
RO/RW changes only set_memory_nx is involved for NX/X. One would await that
the inverse function is called when the NX protection should be removed,
which is not the case here, unless I'm missing something.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When creating an irq, don't allow a concurent driver request until
we have caled map, which will likley call set_chip_and_handler to
change the irq_chip and its operations.
Similarly, when tearing down an IRQ, make sure no new uses come
along while we change the irq back to the nop chip and then reset
the descriptor to freed status.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Create the dts files for each core and splits the devices between the two
cores for P1020RDB.
Core0 has core0 to have memory, l2, i2c, spi, gpio, tdm, dma, usb, eth1,
eth2, sdhc, crypto, global-util, message, pci0, pci1, msi.
Core1 has l2, eth0, crypto.
MPIC is shared between two cores but each core will protect its interrupts
from other core by using "protected-sources" of mpic.
Fix compatible property for global-util node of P1020si.dtsi.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PCIe device in legacy mode can trigger interrupts using the wires #INTA,
#INTB ,#INTC and #INTD. PCI devices are obligated to use #INTx for
interrupts under legacy mode. Each PCI slot or device is typically wired
to different inputs on the interrupt controller.
So, Define interrupt-map and interrupt-map-mask properties for device tree
to of map each PCI interrupt signal to the inputs of the interrupt
controller.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Creates P2020si.dtsi, containing information for P2020 SoC. Modifies dts
files for P2020 based systems to use dtsi file.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Creates P1020si.dtsi, containing information for the P1020 SoC. Modifies dts
files for P1020 based systems to use dtsi file
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Grant Likely <grant.likelY@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This debug option has no overhead other than a slight increase in
kernel size, and makes bug reports more useful. While some end users
may prefer to save the space, as a default on a kernel config aimed
primarily at development on reference boards, it should be enabled.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Even though support for the p5020's on-chip ethernet is not yet upstream,
it is not appropriate to disable all networking support (including
loopback, unix domain sockets, external ethernet devices, etc) in the
defconfig. The networking settings are taken from mpc85xx_smp_defconfig,
minus the drivers for ethernet devices not found on any current e5500
chip.
The other changes are the result of running "make savedefconfig".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for MPIC timers as requestable interrupt sources.
Based on http://patchwork.ozlabs.org/patch/20941/ by Dave Liu.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is no hardware interrupt 0xf7. But now we can express the timer
interrupt using 4-cell interrupts. This requires converting all of the
other interrupt specifiers in the tree as well.
Also add the second timer group, and fix the reg property to only
describe the timer registers.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If the video mode is set to 16-, 24-, or 32-bit pixels, then the pixel data
contains actual levels of red, blue, and green. However, if the video mode
is set to 8-bit pixels, then the 8-bit value represents an index into color
table. This is called "palette mode" on the Freescale DIU video controller.
The DIU driver does not currently support palette mode, but the MPC8610 HPCD
board file returned a non-zero (although incorrect) pixel format value for
8-bit mode.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It may trigger a warning in fs/proc/generic.c:__xlate_proc_name() when
trying to add an entry for the interrupt handler to sysfs.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Without this, we attempt to use doorbells for IPIs, and end up
branching to some bad address. Plus, even for the exceptions
we don't implement, it's good to handle it and get a message out.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The only references to the irq_map[].host field are internal to
arch/powerpc/kernel/irq.c
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some irq_host implementations are using virq_to_host to check if
they are the irq_host for a virtual irq. To allow us to make space
versus time tradeoffs, replace this usage with an assertive
virq_is_host that confirms or denies the irq is associated with the
given irq_host.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Instead of checking for rogue msi numbers via the irq_map host field
set the chip_data to h.host_data (which is the msic struct pointer)
at map and compare it in get_irq.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Building on Grant's efforts to remove the irq_map array, this patch
moves spider-pics use of virq_to_host() to use irq_data_get_chip_data
and sets the irq chip data in the map call, like most other interrupt
controllers in powerpc.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It was called from irq_create_mapping if that was called for a host
and hwirq that was previously mapped, "to update the flags". But the
only implementation was in beat_interrupt and all it did was repeat a
hypervisor call without error checking that was performed with error
checking at the beginning of the map hook. In addition, the comment on
the beat remap hook says it will only called once for a given mapping,
which would apply to map not remap.
All flags should be known by the time the match hook is called, before
we call the map hook. Removing this mostly unused hook will simpify
the requirements of irq_domain concept.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Create a dummy irq_host using the generic dummy irq chip for the secondary
cpus to use. Create a direct irq mapping for the ipi and register the
ipi action handler against it. If for some unlikely reason part of this
fails then don't detect the secondary cpus.
This removes another instance of NO_IRQ_IGNORE, records the ipi stats
for the secondary cpus, and runs the ipi on the interrupt stack.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If none of irq category bits were set mpc52xx_get_irq() would pass
NO_IRQ_IGNORE (-1) to irq_linear_revmap, which does an unsigned compare
and declares the interrupt above the linear map range. It then punts
to irq_find_mapping, which performs a linear search of all irqs,
which will likely miss and only then return NO_IRQ.
If no status bit is set, then we should return NO_IRQ directly.
The interrupt should not be suppressed from spurious counting, in fact
that is the definition of supurious.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As NO_IRQ_IGNORE is only used between the static function cpld_pic_get_irq
and its caller cpld_pic_cascade, and cpld_pic_cascade only uses it to
suppress calling handle_generic_irq, we can change these uses to NO_IRQ
and remove the extra tests and pathlength in cpld_pic_cascade.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
handler_data should be reserved for flow handlers on the dependent
irq, not consumed by the parent irq code that is part of the irq_chip
code. The msi_data pointer was already set in msidesc->irqhost->hostdata
and being copied to irq_data->chipdata in the msidesc->irqhost->map()
method called via create_irq_mapping, so we can obtain the pointer
from there and free the instance it in teardown_msi_irqs.
Also remove the unnecessary cast of irq_get_handler_data in the
cascade handler, which is the demux flow handler of the parent
msi interrupt. (This is the expected usage for handler_data).
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The msi platform device driver was abusing dev.platform_data for its
platform_driver_data. Use the correct pointer for storage.
Platform_data is supposed to be for platforms to communicate to drivers
parameters that are not otherwise discoverable. Its lifetime matches
the platform_device not the platform device driver. It is generally
not needed for drivers that only support systems with device trees.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It was never called because the host is always IRQ_HOST_MAP_LEGACY.
And what it purported to do was mask the interrupt (which will already
have happend if we shutdown the interrupt), then synchronise_irq and
clear the chip pointer, both of which will have been be done by the
caller were we to call unmap on a legacy irq.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These all just clear chip or chipdata fields, which will be done
by the generic code when we call irq_free_descs.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If for some reason the code incrorectly calls the wrong function to
manage the revmap, not only should we warn, we should take action.
However, in the paths we expect to be taken every delivered interrupt
change to WARN_ON_ONCE. Use the if (WARN_ON(x)) format to get the
unlikely for free.
Signed-off-by: Milton Miller <miltonm@bga.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the generic irq code uses a radix tree for sparse interrupts,
the initcall ordering has been changed to initialize radix trees before
irqs. We no longer need to defer creating revmap radix trees to the
arch_initcall irq_late_init.
Also, the kmem caches are allocated so we don't need to use
zalloc_maybe_bootmem.
Signed-off-by: Milton Miller <miltonm@bga.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since we already have a special case in map to set the ipi handler, use
the desired flow.
If we don't find an ics to handle the interrupt complain instead of
returning 0 without having set a chip or handler.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since there are only 4 messages, we can replace the atomic bit set
(which uses atomic load reserve and store conditional sequence) with
a byte stores to seperate bytes. We still have to perform a load
reserve and store conditional sequence to avoid loosing messages on
reception but we can do that with a single call to xchg.
The do {} while and __BIG_ENDIAN specific mask testing was chosen by
looking at the generated asm code. On gcc-4.4, the bit masking becomes
a simple bit mask and test of the register returned from xchg without
storing and loading the value to the stack like attempts with a union
of bytes and an int (or worse, loading single bit constants from the
constant pool into non-voliatle registers that had to be preseved on
the stack). The do {} while avoids an unconditional branch to the
end of the loop to test the entry / repeat condition of a while loop
and instead optimises for the expected single iteration of the loop.
We have a full mb() at the beginning to cover ordering between send,
ipi, and receive so we can use xchg_local and forgo the further
acquire and release barriers of xchg.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Compile the new smp ipi mux and demux code only if a platform
will make use of it. The new config is selected as required.
The new cause_ipi smp op is only available conditionally to point out
configs where the select is required; this makes setting the op an
immediate fail instead of a deferred unresolved symbol at link.
This also creates a new config for power surge powermac upgrade support
that can be disabled in expert mode but is default on.
I also removed the depends / default y on CONFIG_XICS since it is selected
by PSERIES.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Consolidate the mux and demux of ipi messages into smp.c and call
a new smp_ops callback to actually trigger the ipi.
The powerpc architecture code is optimised for having 4 distinct
ipi triggers, which are mapped to 4 distinct messages (ipi many, ipi
single, scheduler ipi, and enter debugger). However, several interrupt
controllers only provide a single software triggered interrupt that
can be delivered to each cpu. To resolve this limitation, each smp_ops
implementation created a per-cpu variable that is manipulated with atomic
bitops. Since these lines will be contended they are optimialy marked as
shared_aligned and take a full cache line for each cpu. Distro kernels
may have 2 or 3 of these in their config, each taking per-cpu space
even though at most one will be in use.
This consolidation removes smp_message_recv and replaces the single call
actions cases with direct calls from the common message recognition loop.
The complicated debugger ipi case with its muxed crash handling code is
moved to debug_ipi_action which is now called from the demux code (instead
of the multi-message action calling smp_message_recv).
I put a call to reschedule_action to increase the likelyhood of correctly
merging the anticipated scheduler_ipi() hook coming from the scheduler
tree; that single required call can be inlined later.
The actual message decode is a copy of the old pseries xics code with its
memory barriers and cache line spacing, augmented with a per-cpu unsigned
long based on the book-e doorbell code. The optional data is set via a
callback from the implementation and is passed to the new cause-ipi hook
along with the logical cpu number. While currently only the doorbell
implemntation uses this data it should be almost zero cost to retrieve and
pass it -- it adds a single register load for the argument from the same
cache line to which we just completed a store and the register is dead
on return from the call. I extended the data element from unsigned int
to unsigned long in case some other code wanted to associate a pointer.
The doorbell check_self is replaced by a call to smp_muxed_ipi_resend,
conditioned on the CPU_DBELL feature. The ifdef guard could be relaxed
to CONFIG_SMP but I left it with BOOKE for now.
Also, the doorbell interrupt vector for book-e was not calling irq_enter
and irq_exit, which throws off cpu accounting and causes code to not
realize it is running in interrupt context. Add the missing calls.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I can't see any reason these functions are needed by machdep.h
and they are all hidden by CONFIG_SMP with no UP alternative.
Also move the declarations for the fallback timebase ops, which
are used to fill in the smp ops.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I have no idea if the beat hypervisor supports multiple cpus in
a partition, but the code has not been touched since these stubs
were added in February of 2007 except to move them in April of 2008.
These are stubs: start_cpu always returns fail (which is dropped),
the message passing and reciving are empty functions, and the top
of file comment says "Incomplete".
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Replace all remaining callers of alloc_maybe_bootmem with
zalloc_maybe_bootmem. The callsite in pci_dn is followed with a
memset to clear the memory, and not zeroing at the other callsites
in the celleb fake pci code could lead to following uninitialized
memory as pointers or even freeing said pointers on error paths.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Its unused, and of the three declarations, one is duplicated in pmac.h,
the second is static and the third is renamed and static.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that MSG_ALL and MSG_ALL_BUT_SELF have been eliminated,
smp_mpic_mesage_pass no longer needs to lookup the cpumask just to
have mpic_send_ipi extract part of it and recode it in a NR_CPUS loop
by mpic_physmask.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that smp_ops->smp_message_pass is always called with an (online) cpu
number for the target remove the checks for MSG_ALL and MSG_ALL_BUT_SELF.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The only user of MSG_ALL_BUT_SELF in the whole kernel tree is powerpc,
and it only uses it to start the debugger. Both debuggers always call
smp_send_debugger_break with MSG_ALL_BUT_SELF, and only mpic can do
anything more optimal than a loop over all online cpus, but all message
passing implementations have to code for this special delivery target.
Convert smp_send_debugger_break to take void and loop calling the smp_ops
message_pass function for each of the other cpus in the online cpumask.
Use raw_smp_processor_id() because we are either entering the debugger
or trying to start kdump and the additional warning it not useful were
it to trigger.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
mpic_set_affinity is allocating and freeing a cpumask var even though
it was breaking the cpumask abstraction when passing the mask to
mpic_physmask. It also didn't have any check for allocatin failure.
Break the cpumask abstraction earlier and use simple bitwise and of the
bits from the mask with the bits of cpu_online_mask.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
mpic_physmask was looping NR_CPUS times over a mask that was passed as
a u32. Since mpic is architecturaly limited to 32 physical cpus, clamp
the logical cpus to 32 when compiling (we could also clamp at runtime
to nr_cpu_ids).
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
c1854e0072 (powerpc: Set nr_cpu_ids early
and use it to free PACAs) copied the formerly static setup_nr_cpu_ids
from init/main.c but 34db18a054 (smp:
move smp setup functions to kernel/smp.c) moved it to kernel/smp.c
with a declaration in include/linux/smp.h, so we can call it instead of
replicating it.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that we never set a cpu above nr_cpu_ids possible we can
limit our initial paca allocation to nr_cpu_ids. We can then
clamp the number of cpus in platforms/iseries/setup.c.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We should not set cpus above nr_cpu_ids to possible. While we
will trigger a warning with CONFIG_CPUMASK_DEBUG, even then the mask
initializers will set the bits beyond what the iterators check and cause
nr_cpu_ids to increase.
Respecting nr_cpu_ids during setup will allow us to use it in our initial
paca allocation. It can be reduced from NR_CPUS by the existing early param
nr_cpus=, which was added in 2b633e3fac (smp:
Use nr_cpus= to set nr_cpu_ids early). We already call parse_early_parms
between finding the command line and allocating the pacas.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
9cb82f2f46 (Make iSeries spin on
__secondary_hold_spinloop, like pSeries) added a load of current_set
but this load was repeated later and we don't even have the paca yet.
It also checked __secondary_hold_spinloop with a 32 bit compare instead
of a 64 bit compare.
b6f6b98a4e (Don't spin on sync instruction
at boot time) missed the copy of the startup code in iseries.
1426d5a3bd (Dynamically allocate pacas)
doesn't allow for pacas to be less than lppacas and recalculated the paca
location from the cpu id in r0 every time through the secondary loop.
Various revisions over time made the comments on conditional branches
confusing with respect to being a hold loop or forward progress
Mostly in-order description of the changes:
Replicate the few lines of code saved by the ugly scoped ifdef CONFIG_SMP
in the secondary loop between yielding on UP and marking time with the
hypervisor on SMP. Always compile the iseries_secondary_yield loop and
use it if the cpu id is above nr_cpu_ids. Change all forward progress
paths to be forward branches to the next numerical label. Assign a
label to all loops. Move all sync instructions from the loops to the
forward progress path. Wait to load current_set until paca is set to go.
Move the iseries_secondary_smp_loop label to cover the whole spin loop.
Add HMT_MEDIUM when we make forward progress.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Starting with 1426d5a3bd (powerpc:
Dynamically allocate pacas) the space for pacas beyond cpu_possible
is freed, but we failed to update the loop in crash.c.
Since c1854e0072 (powerpc: Set nr_cpu_ids
early and use it to free PACAs) the number of pacas allocated is
always nr_cpu_ids.
Signed-off-by: Milton Miller <miltonm@bga.com>
Cc: <stable@kernel.org> # .34.x
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Starting with 1426d5a3bd (powerpc:
Dynamically allocate pacas) we free the memory for pacas beyond
cpu_possible, but we failed to update the loop the secondary cpus use
to find their paca. If the system has running cpu threads for which
the kernel did not allocate a paca for they will search the memory that
was freed. For instance this could happen when the device tree for
a kdump kernel was not updated after a cpu hotplug, or the kernel is
running with more cpus than the kernel was configured.
Since c1854e0072 (powerpc: Set nr_cpu_ids
early and use it to free PACAs) we set nr_cpu_ids before telling the
cpus to advance, so use that to limit the search.
We can't reference nr_cpu_ids without CONFIG_SMP because it is defined
as 1 instead of a memory location, but any extra threads should be sent
to kexec_wait in that case anyways, so make that explicit and remove
the search loop for UP.
Note to stable: The fix also requires
c1854e0072 (powerpc: Set
nr_cpu_ids early and use it to free PACAs) to function. Also
9d07bc841c (Properly handshake CPUs going
out of boot spin loop) affects the second chunk, specifically the branch
target was 3b before and is 4b after that patch, and there was a blank
line before the #ifdef CONFIG_SMP that was removed
Cc: <stable@kernel.org> # .34.x: c1854e0072 powerpc: Set nr_cpu_ids early
Cc: <stable@kernel.org> # .34.x
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 1fc711f7ff (powerpc/kexec: Fix race
in kexec shutdown) moved the write to signal the cpu had exited the kernel
from before the transition to real mode in kexec_smp_wait to kexec_wait.
Unfornately it missed that kexec_wait is used both by cpus leaving the
kernel and by secondary slave cpus that were not allocated a paca for
what ever reason -- they could be beyond nr_cpus or not described in
the current device tree for whatever reason (for example, kexec-load
was not refreshed after a cpu hotplug operation). Cpus coming through
that path they will write to paca[NR_CPUS] which is beyond the space
allocated for the paca data and overwrite memory not allocated to pacas
but very likely still real mode accessable).
Move the write back to kexec_smp_wait, which is used only by cpus that
found their paca, but after the transition to real mode.
Signed-off-by: Milton Miller <miltonm@bga.com>
Cc: <stable@kernel.org> # (1fc711f was backported to 2.6.32)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I have a report of an FWNMI with an r3 value that we think is
corrupt, but since we don't print r3 we have no idea what was
wrong with it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we swtich to direct dma ops, we set the dma data union to have the
dma offset. When we switch back to iommu table ops because of a later
dma_set_mask, we need to restore the iommu table pointer. Without this
change, crashes have been observed on kexec where (for reasons still
being investigated) we fall back to a 32-bit dma mask on a particular
device and then panic because the table pointer is not valid.
The easiset way to find this value is to call
pci_dma_dev_setup_pSeriesLP which will search up the pci tree until it
finds the node with the table.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Milton Miller <miltonm@bga.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a confusing number of ioremap functions. Make things just a
bit simpler by merging ioremap_flags and ioremap_prot.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add ioremap_wc so drivers can request write combining on kernel
mappings.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
After looking at our system call path, Mary Brown suggested that we
should put all mfspr SRR* instructions before any mtspr SRR*.
To test this I used a very simple null syscall (actually getppid)
testcase at http://ozlabs.org/~anton/junkcode/null_syscall.c
I tested with the following changes against the pseries_defconfig:
CONFIG_VIRT_CPU_ACCOUNTING=n
CONFIG_AUDIT=n
to remove the overhead of virtual CPU accounting and syscall
auditing.
POWER6:
baseline: mean = 757.2 cycles sd = 2.108
modified: mean = 759.1 cycles sd = 2.020
POWER7:
baseline: mean = 411.4 cycles sd = 0.138
modified: mean = 404.1 cycles sd = 0.109
So we have 1.77% improvement on POWER7 which looks significant. The
POWER6 suggest a 0.25% slowdown, but the results are within 1
standard deviation and may be in the noise.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A static branch hint will override dynamic branch prediction on
recent POWER CPUs. Since we are about to use more altivec in the
kernel remove the static hint in giveup_altivec that assumes
a userspace task is using altivec.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To make it easier to add optimised versions of copy_page, remove
the 4kB loop for 64kB pages and just do all the work in copy_page.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable iSCSI support for a number of cards. We had the base
networking devices enabled but forgot to enable iSCSI.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable the Qlogic and Emulex 10Gbit adapters.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The variable 'old' is set but not used in the wrprotect functions in
arch/powerpc/include/asm/pgtable-ppc64.h, which can trigger a compiler warning.
Remove the variable, since it's not used anyway.
Signed-off-by: Stratos Psomadakis <psomas@ece.ntua.gr>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Future releases of fimrware will enforce a requirement that DTL buffers
do not cross a 4k boundary. Commit
127493d5dc satisfies this requirement for
CONFIG_VIRT_CPU_ACCOUNTING=y kernels, but if !CONFIG_VIRT_CPU_ACCOUNTING
&& CONFIG_DTL=y, the current code will fail at dtl registration time.
Fix this by making the kmem cache from
127493d5dc visible outside of setup.c and
using the same cache in both dtl.c and setup.c. This requires a bit of
reorganization to ensure ordering of the kmem cache and buffer
allocations.
Note: Since firmware now limits the size of the buffer, I made
dtl_buf_entries read-only in debugfs.
Tested with upcoming firmware with the 4 combinations of
CONFIG_VIRT_CPU_ACCOUNTING and CONFIG_DTL.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we kexec we look for a particular property added by the first
kernel, "linux,direct64-ddr-window-info", per-device where we already
have set up dynamic dma windows. The current code, though, wasn't
initializing the size of this property and thus when we kexec'd, we
would find the property but read uninitialized memory resulting in
garbage ddw values for the kexec'd kernel and panics. Fix this by
setting the size at enable_ddw() time and ensuring that the size of the
found property is valid at dupe_ddw_if_kexec() time.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch below removes an unused config variable found by using a kernel
cleanup script.
Note: I did try to cross compile these but hit erros while doing so..
(gcc is not setup to cross compile) and am unsure if anymore needs to be done.
Please have a look if/when anybody has free time.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The timestamps recorded in the .gz files add no value.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit c56e58537d breaks SMP support in PPC_47x chip.
secondary_ti must be set to current thread info before callin kick_cpu or else
start_secondary_47x will jump into void when trying to return to c-code.
In the current setup secondary_ti is initialized before the CPU idle task is started
and only the boot core will start. I am not sure this is the correct solution, but it
makes SMP possible in my chip.
Note! The HOTPLUG support probably need some fixing to, There is no trampoline code
available in head_44x.S - start_secondary_resume?
Signed-off-by: Kerstin Jonsson <kerstin.jonsson@ericsson.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit b987812b3f left
crash_kexec_wait_realmode() undefined for UP.
Commit 7c7a81b53e defined it for UP but
left it undefined for 32-bit SMP.
Seems like people are getting confused by nested #ifdef's, so move the
definitions of crash_kexec_wait_realmode() after the #ifdef CONFIG_SMP
section.
Compile-tested with 32-bit UP, 32-bit SMP and 64-bit SMP configurations.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
drivercore: revert addition of of_match to struct device
of: fix race when matching drivers
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The 'size' variable contains the correct register size for both AR7
and Titan, but we never used it to ioremap the correct register size.
This problem only shows up on Titan.
[ralf@linux-mips.org: Fixed the fix. The original patch as in patchwork
recognizes the problem correctly then fails to fix it ...]
Reported-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/2380/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the MIPS portion of Joe Perches <joe@perches.com>'s
https://patchwork.linux-mips.org/patch/2172/ which seems to have been
lost in time and space.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As reported in BZ #30352:
https://bugzilla.kernel.org/show_bug.cgi?id=30352
there's a kernel bug related to reading the last allowed page on x86_64.
The _copy_to_user() and _copy_from_user() functions use the following
check for address limit:
if (buf + size >= limit)
fail();
while it should be more permissive:
if (buf + size > limit)
fail();
That's because the size represents the number of bytes being
read/write from/to buf address AND including the buf address.
So the copy function will actually never touch the limit
address even if "buf + size == limit".
Following program fails to use the last page as buffer
due to the wrong limit check:
#include <sys/mman.h>
#include <sys/socket.h>
#include <assert.h>
#define PAGE_SIZE (4096)
#define LAST_PAGE ((void*)(0x7fffffffe000))
int main()
{
int fds[2], err;
void * ptr = mmap(LAST_PAGE, PAGE_SIZE, PROT_READ | PROT_WRITE,
MAP_ANONYMOUS | MAP_PRIVATE | MAP_FIXED, -1, 0);
assert(ptr == LAST_PAGE);
err = socketpair(AF_LOCAL, SOCK_STREAM, 0, fds);
assert(err == 0);
err = send(fds[0], ptr, PAGE_SIZE, 0);
perror("send");
assert(err == PAGE_SIZE);
err = recv(fds[1], ptr, PAGE_SIZE, MSG_WAITALL);
perror("recv");
assert(err == PAGE_SIZE);
return 0;
}
The other place checking the addr limit is the access_ok() function,
which is working properly. There's just a misleading comment
for the __range_not_ok() macro - which this patch fixes as well.
The last page of the user-space address range is a guard page and
Brian Gerst observed that the guard page itself due to an erratum on K8 cpus
(#121 Sequential Execution Across Non-Canonical Boundary Causes Processor
Hang).
However, the test code is using the last valid page before the guard page.
The bug is that the last byte before the guard page can't be read
because of the off-by-one error. The guard page is left in place.
This bug would normally not show up because the last page is
part of the process stack and never accessed via syscalls.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Brian Gerst <brgerst@gmail.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1305210630-7136-1-git-send-email-jolsa@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf evlist: Fix per thread mmap setup
perf tools: Honour the cpu list parameter when also monitoring a thread list
kprobes, x86: Disable irqs during optimized callback
os_dump_core() uses abort() to terminate UML in case of an fatal error.
glibc's abort() calls raise(SIGABRT) which makes use of tgkill().
tgkill() has no effect within UML's kernel threads because they are not
pthreads. As fallback abort() executes an invalid instruction to
terminate the process. Therefore UML gets killed by SIGSEGV and leaves a
ugly log entry in the host's kernel ring buffer.
To get rid of this we use our own abort routine.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable/disable newly documented SMEP (Supervisor Mode Execution Protection) CPU
feature in kernel. CR4.SMEP (bit 20) is 0 at power-on. If the feature is
supported by CPU (X86_FEATURE_SMEP), enable SMEP by setting CR4.SMEP. New kernel
option nosmep disables the feature even if the feature is supported by CPU.
[ hpa: moved the call to setup_smep() until after the vendor-specific
initialization; that ensures that CPUID features are unmasked. We
will still run it before we have userspace (never mind uncontrolled
userspace). ]
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
LKML-Reference: <1305157865-31727-1-git-send-email-fenghua.yu@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Add support for newly documented SMEP (Supervisor Mode Execution Protection)
CPU feature in CR4.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
LKML-Reference: <1305683069-25394-3-git-send-email-fenghua.yu@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Add support for newly documented SMEP (Supervisor Mode Execution Protection) CPU
feature flag.
SMEP prevents the CPU in kernel-mode to jump to an executable page
that has the user flag set in the PTE. This prevents the kernel from
executing user-space code accidentally or maliciously, so it for
example prevents kernel exploits from jumping to specially prepared
user-mode shell code.
[ hpa: added better description by Ingo Molnar ]
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
LKML-Reference: <1305683069-25394-2-git-send-email-fenghua.yu@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Fix build error on i386 by moving function prototypes:
arch/x86/crypto/aesni-intel_glue.c: In function 'aesni_init':
arch/x86/crypto/aesni-intel_glue.c:1263: error: implicit declaration of function 'crypto_fpu_init'
arch/x86/crypto/aesni-intel_glue.c: In function 'aesni_exit':
arch/x86/crypto/aesni-intel_glue.c:1373: error: implicit declaration of function 'crypto_fpu_exit'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Support memset() with enhanced rep stosb. On processors supporting enhanced
REP MOVSB/STOSB, the alternative memset_c_e function using enhanced rep stosb
overrides the fast string alternative memset_c and the original function.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/1305671358-14478-10-git-send-email-fenghua.yu@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Support memmove() by enhanced rep movsb. On processors supporting enhanced
REP MOVSB/STOSB, the alternative memmove() function using enhanced rep movsb
overrides the original function.
The patch doesn't change the backward memmove case to use enhanced rep
movsb.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/1305671358-14478-9-git-send-email-fenghua.yu@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Support memcpy() with enhanced rep movsb. On processors supporting enhanced
rep movsb, the alternative memcpy() function using enhanced rep movsb overrides the original function and the fast string
function.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/1305671358-14478-8-git-send-email-fenghua.yu@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Support copy_to_user/copy_from_user() by enhanced REP MOVSB/STOSB.
On processors supporting enhanced REP MOVSB/STOSB, the alternative
copy_user_enhanced_fast_string function using enhanced rep movsb overrides the
original function and the fast string function.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/1305671358-14478-7-git-send-email-fenghua.yu@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Intel processors are adding enhancements to REP MOVSB/STOSB and the use of
REP MOVSB/STOSB for optimal memcpy/memset or similar functions is recommended.
Enhancement availability is indicated by CPUID.7.0.EBX[9] (Enhanced REP MOVSB/
STOSB).
Support clear_page() with rep stosb for processor supporting enhanced REP MOVSB
/STOSB. On processors supporting enhanced REP MOVSB/STOSB, the alternative
clear_page_c_e function using enhanced REP STOSB overrides the original function
and the fast string function.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/1305671358-14478-6-git-send-email-fenghua.yu@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Add altinstruction_entry macro to generate .altinstructions section
entries from assembly code. This should be less failure-prone than
open-coding.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/1305671358-14478-5-git-send-email-fenghua.yu@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Some string operation functions may be patched twice, e.g. on enhanced REP MOVSB
/STOSB processors, memcpy is patched first by fast string alternative function,
then it is patched by enhanced REP MOVSB/STOSB alternative function.
Add comment for applying alternatives order to warn people who may change the
applying alternatives order for any reason.
[ Documentation-only patch ]
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/1305671358-14478-4-git-send-email-fenghua.yu@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
If kernel intends to use enhanced REP MOVSB/STOSB, it must ensure
IA32_MISC_ENABLE.Fast_String_Enable (bit 0) is set and CPUID.(EAX=07H, ECX=0H):
EBX[bit 9] also reports 1.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/1305671358-14478-3-git-send-email-fenghua.yu@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Intel processors are adding enhancements to REP MOVSB/STOSB and the use of
REP MOVSB/STOSB for optimal memcpy/memset or similar functions is recommended.
Enhancement availability is indicated by CPUID.7.0.EBX[9] (Enhanced REP MOVSB/
STOSB).
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/1305671358-14478-2-git-send-email-fenghua.yu@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Now that we have CONFIG_DYNAMIC_DEBUG there is no need for yet
another flag causing dev_dbg() and pr_debug() statements in the
core PM code to produce output. Moreover, CONFIG_PM_VERBOSE
causes so much output to be generated that it's not really useful
and almost no one sets it.
References: https://bugzilla.kernel.org/show_bug.cgi?id=23182
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* power-domains:
PM: Fix build issue in clock_ops.c for CONFIG_PM_RUNTIME unset
PM: Revert "driver core: platform_bus: allow runtime override of dev_pm_ops"
OMAP1 / PM: Use generic clock manipulation routines for runtime PM
PM / Runtime: Generic clock manipulation rountines for runtime PM (v6)
PM / Runtime: Add subsystem data field to struct dev_pm_info
OMAP2+ / PM: move runtime PM implementation to use device power domains
PM / Platform: Use generic runtime PM callbacks directly
shmobile: Use power domains for platform runtime PM
PM: Export platform bus type's default PM callbacks
PM: Make power domain callbacks take precedence over subsystem ones
* syscore:
PM: Remove sysdev suspend, resume and shutdown operations
PM / PowerPC: Use struct syscore_ops instead of sysdevs for PM
PM / UNICORE32: Use struct syscore_ops instead of sysdevs for PM
PM / AVR32: Use struct syscore_ops instead of sysdevs for PM
PM / Blackfin: Use struct syscore_ops instead of sysdevs for PM
ARM / Samsung: Use struct syscore_ops for "core" power management
ARM / PXA: Use struct syscore_ops for "core" power management
ARM / SA1100: Use struct syscore_ops for "core" power management
ARM / Integrator: Use struct syscore_ops for core PM
ARM / OMAP: Use struct syscore_ops for "core" power management
ARM: Use struct syscore_ops instead of sysdevs for PM in common code
acpi_sleep=s4_nonvs is superseded by acpi_sleep=nonvs, so remove it.
Signed-off-by: WANG Cong <amwang@redhat.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Len Brown <lenb@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
CPUID leaf 7, subleaf 0 returns the maximum subleaf in EAX, not the
number of subleaves. Since so far only subleaf 0 is defined (and only
the EBX bitfield) we do not need to qualify the test.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/1305660806-17519-1-git-send-email-fenghua.yu@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@kernel.org> 2.6.36..39
Trying to enable the local APIC timer on early K8 revisions
uncovers a number of other issues with it, in conjunction with
the C1E enter path on AMD. Fixing those causes much more churn
and troubles than the benefit of using that timer brings so
don't enable it on K8 at all, falling back to the original
functionality the kernel had wrt to that.
Reported-and-bisected-by: Nick Bowler <nbowler@elliptictech.com>
Cc: Boris Ostrovsky <Boris.Ostrovsky@amd.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Hans Rosenfeld <hans.rosenfeld@amd.com>
Cc: Nick Bowler <nbowler@elliptictech.com>
Cc: Joerg-Volker-Peetz <jvpeetz@web.de>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1305636919-31165-3-git-send-email-bp@amd64.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit e20a2d205c, as it crashes
certain boxes with specific AMD CPU models.
Moving the lower endpoint of the Erratum 400 check to accomodate
earlier K8 revisions (A-E) opens a can of worms which is simply
not worth to fix properly by tweaking the errata checking
framework:
* missing IntPenging MSR on revisions < CG cause #GP:
http://marc.info/?l=linux-kernel&m=130541471818831
* makes earlier revisions use the LAPIC timer instead of the C1E
idle routine which switches to HPET, thus not waking up in
deeper C-states:
http://lkml.org/lkml/2011/4/24/20
Therefore, leave the original boundary starting with K8-revF.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
ZONE_DMA is unnecessary for a large number of machines that do not
require less than 32-bit DMA addressing, e.g. ISA legacy DMA or PCI
cards with a restricted DMA address mask.
This patch allows users to disable ZONE_DMA for x86 if they know they
will not be using such devices with their kernel.
This prevents the VM from unnecessarily reserving a ratio of memory
(defaulting to 1/256th of system capacity) with lowmem_reserve_ratio
for such allocations when it will never be used.
Signed-off-by: David Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.00.1105161353560.4353@chino.kir.corp.google.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The function mmu_inval_dma_area takes a virtual address as a parameter
which is problematic in case the buffer is located in highmem and the
mapping currently is unavailable.
Since the function was only implemented for LEON this patch removes
calls to it in non LEON code paths and renames it to dma_make_coherent
which instead takes a physical address (which for now is unused since we
flush the whole cache). This way it is possible to remove several unnecessary
calls to page_address which will fail if the virtual mapping is unavailable.
Signed-off-by: Kristoffer Glembo <kristoffer@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt new API. Almost change is trivial, most important change are to
remove following like =operator.
cpumask_t cpu_mask = *mm_cpumask(mm);
cpus_allowed = current->cpus_allowed;
Because cpumask_var_t is =operator unsafe. These usage might prevent
kernel core improvement.
No functional change.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steppings A1 and B0 of Celeron Covington are currently misdetected as
Pentium II (Dixon). Fix it by removing the stepping check.
[ hpa: this fixes this specific bug... the CPUID documentation
specifies that the L2 cache size can disambiguate additional CPUs;
this patch does not fix that. ]
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Link: http://lkml.kernel.org/r/201105162138.15416.linux@rainbow-software.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The sun4d does not seem to have a distingstion between soft and hard
IRQs. When generating IPIs the generated IRQ looks like a hard IRQ,
this patch adds a "IPI check" in the sun4d irq trap handler at a
predefined IRQ number (SUN4D_IPI_IRQ). Before generating an IPI
a per-cpu memory structure is modified for the "IPI check" to
successfully detect a IPI request to a specific processor, the check
clears the IPI work requested.
All three IPIs (resched, single and cpu-mask) use the same IRQ
number.
The IPI IRQ should preferrably be on a separate IRQ and definitly
not shared with IRQ handlers requesting IRQ with IRQF_SHARED.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the three IPIs (resched, single and cpu-mask) generation
and interrupt handler catch. The sun4m has 15 soft-IRQs and three
of them is used with this patch, the three IPIs was previously
implemented with the cross-call IRQ15 which does not work with
locking routines such as spinlocks because IRQ15 is NMI, it may
cause deadlock.
The IRQ trap handler code assumes (in the same spritit as the old
it seems) that hard interrupts will be generated until handled
(level), when a IRQ happens the IRQ pending register is checked
for pending soft-IRQs. When both hard and soft IRQ happens at the
same time only soft-IRQs are handled.
The old code implemented a soft-IRQ traphandler at IRQ14 which
called smp_reschedule_irq which in turn called set_need_resched.
It seems to be an old relic and is replaced with the interrupt
traphander exit code RESTORE_ALL, it calls schedule() when
appropriate.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements SMP IPIs on LEON using software generated
IRQs to signal between CPUs.
The IPI IRQ number is set by using the ipi_num property in the
device tree, or defaults to 13. LEON SMP systems should reserve
IRQ 13 (and IRQ 15) to Linux in order for the defaults to work.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current sparc32 SMP IPI generation is implemented the
cross call function. The cross call function uses IRQ15 the
NMI, this is has the effect that IPIs will interrupt IRQ
critical areas and hang the system. Typically on/after
spin_lock_irqsave calls can be aborted.
The cross call functionality must still exist to flush
cache/TLBS.
This patch provides CPU models a custom way to implement
generation of IPIs on the generic code's request. The
typical approach is to generate an IRQ for each IPI case.
After this patch each sparc32 SMP CPU model needs to
implement IPIs in order to function properly.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the mcount offset adjustment in the recordmcount.pl/recordmcount.[ch]
at compile time and not in ftrace_call_adjust at run time.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Do the mcount offset adjustment in the recordmcount.pl/recordmcount.[ch]
at compile time and not in ftrace_call_adjust at run time.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The section called .discard.text has tracing attached to it and is
currently ignored by ftrace. But it does include a call to the mcount
stub. Adding a notrace to the code keeps gcc from adding the useless
mcount caller to it.
Link: http://lkml.kernel.org/r/20110421023739.243651696@goodmis.org
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
We provide two slots to disable cache indices, and have a check to
prevent both slots to be used for the same index.
If the user disables the same index on different subcaches, both slots
will hold the same index, e.g.
$ echo 2047 > /sys/devices/system/cpu/cpu0/cache/index3/cache_disable_0
$ cat /sys/devices/system/cpu/cpu0/cache/index3/cache_disable_0
2047
$ echo 1050623 > /sys/devices/system/cpu/cpu0/cache/index3/cache_disable_1
$ cat /sys/devices/system/cpu/cpu0/cache/index3/cache_disable_1
2047
due to the fact that the check was looking only at index bits [11:0]
and was ignoring writes to bits outside that range. The more correct
fix is to simply check whether the index is within the bounds of
[0..l3->indices].
While at it, cleanup comments and drop now-unused local macros.
Signed-off-by: Frank Arnold <frank.arnold@amd.com>
Link: http://lkml.kernel.org/r/1305553188-21061-3-git-send-email-bp@amd64.org
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
732eacc054 converted code around the
kernel using nested max() macros to use the new max3 macro but forgot to
remove the old line in intel_cacheinfo.c. Fix it.
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Frank Arnold <farnold@amd64.org>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1305553188-21061-2-git-send-email-bp@amd64.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Convert OMAP1 to using the new generic clock manipulation routines
and a device power domain for runtime PM instead of overriding the
platform bus type's runtime PM callbacks. This allows us to simplify
OMAP1-specific code and to share some code with other platforms
(shmobile in particular).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
If we have CONFIG_XEN and the other parameters to build an
Linux kernel that is non-privileged, the xen_[find|register|unregister]_
device_domain_owner functions should not be compiled. They should
use the nops defined in arch/x86/include/asm/xen/pci.h instead.
This fixes:
arch/x86/pci/xen.c:496: error: redefinition of ‘xen_find_device_domain_owner’
arch/x86/include/asm/xen/pci.h:25: note: previous definition of ‘xen_find_device_domain_owner’ was here
arch/x86/pci/xen.c:510: error: redefinition of ‘xen_register_device_domain_owner’
arch/x86/include/asm/xen/pci.h:29: note: previous definition of ‘xen_register_device_domain_owner’ was here
arch/x86/pci/xen.c:532: error: redefinition of ‘xen_unregister_device_domain_owner’
arch/x86/include/asm/xen/pci.h:34: note: previous definition of ‘xen_unregister_device_domain_owner’ was here
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP3: set the core dpll clk rate in its set_rate function
omap: iommu: Return IRQ_HANDLED in fault handler when no fault occured
This patch fixes a bug reported by a customer, who found
that many unreasonable error interrupts reported on all
non-boot CPUs (APs) during the system boot stage.
According to Chapter 10 of Intel Software Developer Manual
Volume 3A, Local APIC may signal an illegal vector error when
an LVT entry is set as an illegal vector value (0~15) under
FIXED delivery mode (bits 8-11 is 0), regardless of whether
the mask bit is set or an interrupt actually happen. These
errors are seen as error interrupts.
The initial value of thermal LVT entries on all APs always reads
0x10000 because APs are woken up by BSP issuing INIT-SIPI-SIPI
sequence to them and LVT registers are reset to 0s except for
the mask bits which are set to 1s when APs receive INIT IPI.
When the BIOS takes over the thermal throttling interrupt,
the LVT thermal deliver mode should be SMI and it is required
from the kernel to keep AP's LVT thermal monitoring register
programmed as such as well.
This issue happens when BIOS does not take over thermal throttling
interrupt, AP's LVT thermal monitor register will be restored to
0x10000 which means vector 0 and fixed deliver mode, so all APs will
signal illegal vector error interrupts.
This patch check if interrupt delivery mode is not fixed mode before
restoring AP's LVT thermal monitor register.
Signed-off-by: Youquan Song <youquan.song@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Yong Wang <yong.y.wang@intel.com>
Cc: hpa@linux.intel.com
Cc: joe@perches.com
Cc: jbaron@redhat.com
Cc: trenn@suse.de
Cc: kent.liu@intel.com
Cc: chaohong.guo@intel.com
Cc: <stable@kernel.org> # As far back as possible
Link: http://lkml.kernel.org/r/1303402963-17738-1-git-send-email-youquan.song@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Loading fpu without aesni-intel does nothing. Loading aesni-intel
without fpu causes modes like xts to fail. (Unloading
aesni-intel will restore those modes.)
One solution would be to make aesni-intel depend on fpu, but it
seems cleaner to just combine the modules.
This is probably responsible for bugs like:
https://bugzilla.redhat.com/show_bug.cgi?id=589390
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Conflicts:
arch/ia64/kernel/cyclone.c
arch/mips/kernel/i8253.c
arch/x86/kernel/i8253.c
Reason: Resolve conflicts so further cleanups do not conflict further
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Convert MIPS i8253 clocksource code to use generic i8253 clocksource.
Acked-by: John Stultz <john.stultz@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert x86 i8253 clocksource code to use generic i8253 clocksource.
Acked-by: John Stultz <john.stultz@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the footbridge isa-timer code to use generic i8253 clocksource.
Acked-by: John Stultz <john.stultz@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Wire up the syscalls:
name_to_handle_at
open_by_handle_at
clock_adjtime
syncfs
and adjust some whitespace in the neighbourhood to align commments.
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Converts alpha to use clocksource_register_hz.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Matt Turner <mattst88@gmail.com>
John Crispin
Maxin John
Jayachandran C
Sebastian Siewior
Gabriel Paubert
Benjamin Herrenschmidt
Milton Miller
Nishanth Aravamudan
Jan Glauber
Prabhakar Kushwaha
Scott Wood
Timur Tabi
Geert Uytterhoeven
Kumar Gala
Anton Blanchard
Stratos Psomadakis
Michal Marek
Justin Mattock
kerstin jonsson
Ben Hutchings
Linus Torvalds
Ingo Molnar
Grant Likely
Ralf Baechle
Florian Fainelli
Jiri Olsa
Richard Weinberger
Fenghua Yu
Randy Dunlap
Rafael J. Wysocki
Amerigo Wang
Borislav Petkov
David Rientjes
Kristoffer Glembo
KOSAKI Motohiro
Ondrej Zary
Daniel Hellstrom
Martin Schwidefsky
Steven Rostedt
Frank Arnold
Konrad Rzeszutek Wilk
Youquan Song
Andy Lutomirski
Thomas Gleixner
Russell King
Michael Cree
John Stultz