The important issue here is incorporating the different in data_offset
into calculations concerning when we might need to over-write data
that is still thought to be valid.
To this end we find the minimum offset difference across all devices
and add that where appropriate.
Signed-off-by: NeilBrown <neilb@suse.de>
As there can now be two different data_offsets - an 'old' and
a 'new' - we need to carefully choose between them.
Signed-off-by: NeilBrown <neilb@suse.de>
When reshaping we can avoid costly intermediate backup by
changing the 'start' address of the array on the device
(if there is enough room).
So as a first step, allow such a change to be requested
through sysfs, and recorded in v1.x metadata.
(As we didn't previous check that all 'pad' fields were zero,
we need a new FEATURE flag for this.
A (belatedly) check that all remaining 'pad' fields are
zero to avoid a repeat of this)
The new data offset must be requested separately for each device.
This allows each to have a different change in the data offset.
This is not likely to be used often but as data_offset can be
set per-device, new_data_offset should be too.
This patch also removes the 'acknowledged' arg to rdev_set_badblocks as
it is never used and never will be. At the same time we add a new
arg ('in_new') which is currently always zero but will be used more
soon.
When a reshape finishes we will need to update the data_offset
and rdev->sectors. So provide an exported function to do that.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently a reshape operation always progresses from the start
of the array to the end unless the number of devices is being
reduced, in which case it progressed in the opposite direction.
To reverse a partial reshape which changes the number of devices
you can stop the array and re-assemble with the raid-disks numbers
reversed and it will undo.
However for a reshape that does not change the number of devices
it is not possible to reverse the reshape in the middle - you have to
wait until it completes.
So add a 'reshape_direction' attribute with is either 'forwards' or
'backwards' and can be explicitly set when delta_disks is zero.
This will become more important when we allow the data_offset to
change in a reshape. Then the explicit statement of what direction is
being used will be more useful.
This can be enabled in raid5 trivially as it already supports
reverse reshape and just needs to use a different trigger to request it.
Signed-off-by: NeilBrown <neilb@suse.de>
A flush request is usually issued in transaction commit code path, so
using GFP_KERNEL to allocate memory for flush request bio falls into
the classic deadlock issue.
This is suitable for any -stable kernel to which it applies as it
avoids a possible deadlock.
Cc: stable@vger.kernel.org
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The old code was
sector_div(stride, fc);
the new code was
sector_dir(size, conf->near_copies);
'size' is right (the stride various wasn't really needed), but
'fc' means 'far_copies', and that is an important difference.
Signed-off-by: NeilBrown <neilb@suse.de>
Use del_timer_sync to remove timer before mddev_suspend finishes.
We don't want a timer going off after an mddev_suspend is called. This is
especially true with device-mapper, since it can call the destructor function
immediately following a suspend. This results in the removal (kfree) of the
structures upon which the timer depends - resulting in a very ugly panic.
Therefore, we add a del_timer_sync to mddev_suspend to prevent this.
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
raid10 stores dev_sectors in 'conf' separately from the one in
'mddev' because it can have a very significant effect on block
addressing and so need to be updated carefully.
However raid10_resize isn't updating it at all!
To update it correctly, we need to make sure it is a proper
multiple of the chunksize taking various details of the layout
in to account.
This calculation is currently done in setup_conf. So split it
out from there and call it from raid10_resize as well.
Then set conf->dev_sectors properly.
Signed-off-by: NeilBrown <neilb@suse.de>
commit 61a0d80c "md/bitmap: discard CHUNK_BLOCK_SHIFT macro"
replaced CHUNK_BLOCK_RATIO() by the same text that was
replacing CHUNK_BLOCK_SHIFT() - which is clearly wrong.
The result is that 'chunks' is often too small by 1,
which can sometimes result in a crash (not sure how).
So use the correct replacement, and get rid of CHUNK_BLOCK_RATIO
which is no longe used.
Reported-by: Karl Newman <siliconfiend@gmail.com>
Tested-by: Karl Newman <siliconfiend@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Fix for an issue causing hibernation to hang on systems with highmem (that
practically means i386) due to broken memory management (bug introduced in 3.2,
so -stable material) and PM documentation update making the freezer
documentation follow the code again after some recent updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=HaVL
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael J. Wysocki:
"Fix for an issue causing hibernation to hang on systems with highmem
(that practically means i386) due to broken memory management (bug
introduced in 3.2, so -stable material) and PM documentation update
making the freezer documentation follow the code again after some
recent updates."
* tag 'pm-for-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Freezer / Docs: Update documentation about freezing of tasks
PM / Hibernate: fix the number of pages used for hibernate/thaw buffering
The autofs packet size has had a very unfortunate size problem on x86:
because the alignment of 'u64' differs in 32-bit and 64-bit modes, and
because the packet data was not 8-byte aligned, the size of the autofsv5
packet structure differed between 32-bit and 64-bit modes despite
looking otherwise identical (300 vs 304 bytes respectively).
We first fixed that up by making the 64-bit compat mode know about this
problem in commit a32744d4ab ("autofs: work around unhappy compat
problem on x86-64"), and that made a 32-bit 'systemd' work happily on a
64-bit kernel because everything then worked the same way as on a 32-bit
kernel.
But it turned out that 'automount' had actually known and worked around
this problem in user space, so fixing the kernel to do the proper 32-bit
compatibility handling actually *broke* 32-bit automount on a 64-bit
kernel, because it knew that the packet sizes were wrong and expected
those incorrect sizes.
As a result, we ended up reverting that compatibility mode fix, and
thus breaking systemd again, in commit fcbf94b9de.
With both automount and systemd doing a single read() system call, and
verifying that they get *exactly* the size they expect but using
different sizes, it seemed that fixing one of them inevitably seemed to
break the other. At one point, a patch I seriously considered applying
from Michael Tokarev did a "strcmp()" to see if it was automount that
was doing the operation. Ugly, ugly.
However, a prettier solution exists now thanks to the packetized pipe
mode. By marking the communication pipe as being packetized (by simply
setting the O_DIRECT flag), we can always just write the bigger packet
size, and if user-space does a smaller read, it will just get that
partial end result and the extra alignment padding will simply be thrown
away.
This makes both automount and systemd happy, since they now get the size
they asked for, and the kernel side of autofs simply no longer needs to
care - it could pad out the packet arbitrarily.
Of course, if there is some *other* user of autofs (please, please,
please tell me it ain't so - and we haven't heard of any) that tries to
read the packets with multiple writes, that other user will now be
broken - the whole point of the packetized mode is that one system call
gets exactly one packet, and you cannot read a packet in pieces.
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Miller <davem@davemloft.net>
Cc: Ian Kent <raven@themaw.net>
Cc: Thomas Meyer <thomas@m3y3r.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The file Documentation/power/freezing-of-tasks.txt was still referencing
the TIF_FREEZE flag, that was removed by the commit
d88e4cb67197d007fb778d62fe17360e970d5bfa(freezer: remove now unused
TIF_FREEZE).
This patch removes all the references of TIF_FREEZE that were left
behind.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The actual internal pipe implementation is already really about
individual packets (called "pipe buffers"), and this simply exposes that
as a special packetized mode.
When we are in the packetized mode (marked by O_DIRECT as suggested by
Alan Cox), a write() on a pipe will not merge the new data with previous
writes, so each write will get a pipe buffer of its own. The pipe
buffer is then marked with the PIPE_BUF_FLAG_PACKET flag, which in turn
will tell the reader side to break the read at that boundary (and throw
away any partial packet contents that do not fit in the read buffer).
End result: as long as you do writes less than PIPE_BUF in size (so that
the pipe doesn't have to split them up), you can now treat the pipe as a
packet interface, where each read() system call will read one packet at
a time. You can just use a sufficiently big read buffer (PIPE_BUF is
sufficient, since bigger than that doesn't guarantee atomicity anyway),
and the return value of the read() will naturally give you the size of
the packet.
NOTE! We do not support zero-sized packets, and zero-sized reads and
writes to a pipe continue to be no-ops. Also note that big packets will
currently be split at write time, but that the size at which that
happens is not really specified (except that it's bigger than PIPE_BUF).
Currently that limit is the system page size, but we might want to
explicitly support bigger packets some day.
The main user for this is going to be the autofs packet interface,
allowing us to stop having to care so deeply about exact packet sizes
(which have had bugs with 32/64-bit compatibility modes). But user
space can create packetized pipes with "pipe2(fd, O_DIRECT)", which will
fail with an EINVAL on kernels that do not support this interface.
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Miller <davem@davemloft.net>
Cc: Ian Kent <raven@themaw.net>
Cc: Thomas Meyer <thomas@m3y3r.de>
Cc: stable@kernel.org # needed for systemd/autofs interaction fix
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are some tiny drivers/staging/ bugfixes. Some build fixes that
were recently reported, as well as one kfree bug that is hitting a
number of users.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+dZeoACgkQMUfUDdst+yl3YACghMr131zQer1yIJbXvcTGstR3
TrkAn2X3gPqHnrXUdlGS5zUxeTl0fL5S
=wG0/
-----END PGP SIGNATURE-----
Merge tag 'staging-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree fixes from Greg Kroah-Hartman:
"Here are some tiny drivers/staging/ bugfixes. Some build fixes that
were recently reported, as well as one kfree bug that is hitting a
number of users."
* tag 'staging-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: ozwpan: Fix bug where kfree is called twice.
staging: octeon-ethernet: fix build errors by including interrupt.h
staging: zcache: fix Kconfig crypto dependency
staging: tidspbridge: remove usage of OMAP2_L4_IO_ADDRESS
Here are a number of small USB fixes for 3.4-rc5.
Nothing major, as before, some USB gadget fixes. There's a crash fix
for a number of ASUS laptops on resume that had been reported by a
number of different people. We think the fix might also pertain to
other machines, as this was a BIOS bug, and they seem to travel to
different models and manufacturers quite easily. Other than that, some
other reported problems fixed as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+dZ7kACgkQMUfUDdst+ylxwACdFS4V69bnBi2nw9spEYClh+FB
SToAoLUFsDiTDexIMIMWZkCyq+bqVLG+
=Pzvi
-----END PGP SIGNATURE-----
Merge tag 'usb-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a number of small USB fixes for 3.4-rc5.
Nothing major, as before, some USB gadget fixes. There's a crash fix
for a number of ASUS laptops on resume that had been reported by a
number of different people. We think the fix might also pertain to
other machines, as this was a BIOS bug, and they seem to travel to
different models and manufacturers quite easily. Other than that,
some other reported problems fixed as well."
* tag 'usb-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: gadget: udc-core: fix incompatibility with dummy-hcd
usb: gadget: udc-core: fix wrong call order
USB: cdc-wdm: fix race leading leading to memory corruption
USB: EHCI: fix crash during suspend on ASUS computers
usb gadget: uvc: uvc_request_data::length field must be signed
usb: gadget: dummy: do not call pullup() on udc_stop()
usb: musb: davinci.c: add missing unregister
usb: musb: drop __deprecated flag
USB: gadget: storage gadgets send wrong error code for unknown commands
usb: otg: gpio_vbus: Add otg transceiver events and notifiers
Pull btrfs fixes from Chris Mason:
"This has our collection of bug fixes. I missed the last rc because I
thought our patches were making NFS crash during my xfs test runs.
Turns out it was an NFS client bug fixed by someone else while I tried
to bisect it.
All of these fixes are small, but some are fairly high impact. The
biggest are fixes for our mount -o remount handling, a deadlock due to
GFP_KERNEL allocations in readdir, and a RAID10 error handling bug.
This was tested against both 3.3 and Linus' master as of this morning."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (26 commits)
Btrfs: reduce lock contention during extent insertion
Btrfs: avoid deadlocks from GFP_KERNEL allocations during btrfs_real_readdir
Btrfs: Fix space checking during fs resize
Btrfs: fix block_rsv and space_info lock ordering
Btrfs: Prevent root_list corruption
Btrfs: fix repair code for RAID10
Btrfs: do not start delalloc inodes during sync
Btrfs: fix that check_int_data mount option was ignored
Btrfs: don't count CRC or header errors twice while scrubbing
Btrfs: fix btrfs_ioctl_dev_info() crash on missing device
btrfs: don't return EINTR
Btrfs: double unlock bug in error handling
Btrfs: always store the mirror we read the eb from
fs/btrfs/volumes.c: add missing free_fs_devices
btrfs: fix early abort in 'remount'
Btrfs: fix max chunk size check in chunk allocator
Btrfs: add missing read locks in backref.c
Btrfs: don't call free_extent_buffer twice in iterate_irefs
Btrfs: Make free_ipath() deal gracefully with NULL pointers
Btrfs: avoid possible use-after-free in clear_extent_bit()
...
Nothing controversial, just another batch of fixes:
- Samsung/exynos fixes for more merge window fallout: build errors and
warnings mostly, but also some clock/device setup issues on exynos4/5
- PXA bug and warning fixes related to gpio and pinmux
- IRQ domain conversion bugfixes for U300 and MSM
- A regulator setup fix for U300
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=V4y6
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Nothing controversial, just another batch of fixes:
- Samsung/exynos fixes for more merge window fallout: build errors
and warnings mostly, but also some clock/device setup issues on
exynos4/5
- PXA bug and warning fixes related to gpio and pinmux
- IRQ domain conversion bugfixes for U300 and MSM
- A regulator setup fix for U300"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: PXA2xx: MFP: fix potential direction bug
ARM: PXA2xx: MFP: fix bug with MFP_LPM_KEEP_OUTPUT
arm/sa1100: fix sa1100-rtc memory resource
ARM: pxa: fix gpio wakeup setting
ARM: SAMSUNG: add missing MMC_CAP2_BROKEN_VOLTAGE capability
ARM: EXYNOS: Fix compilation error when CONFIG_OF is not defined
ARM: EXYNOS: Fix resource on dev-dwmci.c
ARM: S3C24XX: Fix build warning for S3C2410_PM
ARM: mini2440_defconfig: Fix build error
ARM: msm: Fix gic irqdomain support
ARM: EXYNOS: Fix incorrect initialization of GIC
ARM: EXYNOS: use 'exynos4-sdhci' as device name for sdhci controllers
ARM: u300: bump all IRQ numbers by one
ARM: ux300: Fix unimplementable regulation constraints
Pull drm fixes from Dave Airlie:
"As soon as I sent the non-urgent stack, two important fixes come in:
- i915: fixes SNB GPU hangs in a number of 3D apps
- radeon: initial fix for VGA on LLano system, 3 or 4 of us have
spent time debugging this, and Jerome finally figured out the magic
bit the BIOS/fglrx set that we didn't. This at least should get
things working, there may be future reliability fixes."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Set the Stencil Cache eviction policy to non-LRA mode.
drm/radeon/kms: need to set up ss on DP bridges as well
This reverts commit a32744d4ab.
While that commit was technically the right thing to do, and made the
x86-64 compat mode work identically to native 32-bit mode (and thus
fixing the problem with a 32-bit systemd install on a 64-bit kernel), it
turns out that the automount binaries had workarounds for this compat
problem.
Now, the workarounds are disgusting: doing an "uname()" to find out the
architecture of the kernel, and then comparing it for the 64-bit cases
and fixing up the size of the read() in automount for those. And they
were confused: it's not actually a generic 64-bit issue at all, it's
very much tied to just x86-64, which has different alignment for an
'u64' in 64-bit mode than in 32-bit mode.
But the end result is that fixing the compat layer actually breaks the
case of a 32-bit automount on a x86-64 kernel.
There are various approaches to fix this (including just doing a
"strcmp()" on current->comm and comparing it to "automount"), but I
think that I will do the one that teaches pipes about a special "packet
mode", which will allow user space to not have to care too deeply about
the padding at the end of the autofs packet.
That change will make the compat workaround unnecessary, so let's revert
it first, and get automount working again in compat mode. The
packetized pipes will then fix autofs for systemd.
Reported-and-requested-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: Ian Kent <raven@themaw.net>
Cc: stable@kernel.org # for 3.3
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clearing bit 5 of CACHE_MODE_0 is necessary to prevent GPU hangs in
OpenGL programs such as Google MapsGL, Google Earth, and gzdoom when
using separate stencil buffers. Without it, the GPU tries to use the
LRA eviction policy, which isn't supported. This was supposed to be off
by default, but seems to be on for many machines.
This cannot be done in gen6_init_clock_gating with most of the other
workaround bits; the render ring needs to exist. Otherwise, the
register write gets dropped on the floor (one printk will show it
changed, but a second printk immediately following shows the value
reverts to the old one).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=47535
Cc: stable@vger.kernel.org
Cc: Rob Castle <futuredub@gmail.com>
Cc: Eric Appleman <erappleman@gmail.com>
Cc: aaron667@gmx.net
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull CIFS fixes from Steve French.
* git://git.samba.org/sfrench/cifs-2.6:
Use correct conversion specifiers in cifs_show_options
CIFS: Show backupuid/gid in /proc/mounts
cifs: fix offset handling in cifs_iovec_write
- In the low-level assembler code we would jump to check events
even if none were present. This incorrect behavior had been there
since 2.6.27 days!
- When using the fast-path for ACK-ing interrupts we were using the
Linux IRQ numbers instead of the Xen ones (and they can differ) and
missing interrupts in process.
- Fix bootup crashes when ACPI hotplug CPUs were present and they
would expand past the set number of CPUs we were allocated.
- Deal with broken BIOSes when uploading C-states to the hypervisor.
- Disable the cpuid check for MWAIT_LEAF if the ACPI PAD driver is
loaded. If the ACPI PAD driver is used it will crash, so lets not
export the functionality so the ACPI PAD driver won't load.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPmwl0AAoJEFjIrFwIi8fJdMoIAKliOTtWwaBTH8VzrVK3f2+x
Hdp7KQuFB6SM74Be2TMYvev7v2q4u35eLCf/huj+vr7MVjOKqjKKrVLLuZKU1sKz
a9ohLy0el6BDgL6Bkywm9AhReCXGz0sRi2g2nVV1HhUHjaJiMC7Rbd/ac+8FtYTF
d/paaMWxGshtJwjHPn6XZhTJ54Rguwbp4cW+R/6IVDAfI3BH0nBWNgj53lwKpvmh
7c7rzwLJRokW0hVoqGvpeT6pIeRqDOMBBQP5BhGe8YCl3qASJBzWPmzQHAqL/h5Z
ieDmkQCyKZXew+jyV3Xq+V0ZuQekUCfz/sapRh+F32ZB2jxCcaeRLzPNLVzAs5o=
=m4wA
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.4-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fixes from Konrad Rzeszutek Wilk:
"Some of these had been in existence since the 2.6.27 days, some since
3.0 - and some due to new features added in v3.4.
The one that is most interesting is David's one - in the low-level
assembler code we had be checking events needlessly. With his patch
now we do it when the appropriate flag is set - with the added benefit
that we can process events faster. Stefano's is fixing a mistake
where the Linux IRQ numbers were ACK-ed instead of the Xen IRQ,
resulting in missing interrupts. The other ones are bootup related
that can show up on various hardware."
- In the low-level assembler code we would jump to check events even if
none were present. This incorrect behavior had been there since
2.6.27 days!
- When using the fast-path for ACK-ing interrupts we were using the
Linux IRQ numbers instead of the Xen ones (and they can differ) and
missing interrupts in process.
- Fix bootup crashes when ACPI hotplug CPUs were present and they would
expand past the set number of CPUs we were allocated.
- Deal with broken BIOSes when uploading C-states to the hypervisor.
- Disable the cpuid check for MWAIT_LEAF if the ACPI PAD driver is
loaded. If the ACPI PAD driver is used it will crash, so lets not
export the functionality so the ACPI PAD driver won't load.
* tag 'stable/for-linus-3.4-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: correctly check for pending events when restoring irq flags
xen/acpi: Workaround broken BIOSes exporting non-existing C-states.
xen/smp: Fix crash when booting with ACPI hotplug CPUs.
xen: use the pirq number to check the pirq_eoi_map
xen/enlighten: Disable MWAIT_LEAF so that acpi-pad won't be loaded.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPmubjAAoJEEFnBt12D9kBPZ4P/2wrFqNy2+Fxatstmb1GKwqW
Yx0acIZkJK/gfZetFDSiTzM8bcxp/oz2lfqHE7xFq96s36wSZyO9B9Ry+YiD9x4g
wzN/Gb7UufnuSEEJo19E13sJxMXJ/4dVFHKtJnxSL3k9lC6nO/YkEn7C2OXE9gXy
d3a8H2jyGK9CPPHzQVxDP+9vYj8RpZcXz1M49H8dZ7UZblPfHlvPNzsclKbuTiFK
8zg16sX01BjvbawwMuAuJH/SGytKpM7WtlzDni/OplqX3CDjIoNZ8BEqDgXDVcS8
dwhmhPEf89v5ctWhaDHlskwAkL8oFjwFAHMZ7pjiIZ1aTxPPEKtyegVqPKoQwQmK
XCbjb9SqFNRXI2nIkbeX1xGHQS1wngRcfWJ13qLDEDi3d3aGLUJDYTtMHPrjvNnI
kzqbNC6fFuKZNOaDYMb1nqV3oWa8VLlDhXgEn5K8ZzBInZ/12LsqybRqImwLQnN0
flRCcOWApbHmJB64IAI1NzbG5Y6FxG53lwW+bwkw83W1fWw1WaUNNvJ8HBfDoN3G
QflSqY8TtRE5vGvTburRbDIF3YBeGsaPDTksIg2t82PZ1SabUfIhpWRbhzS6YvMH
NiKlgk88Q3VHLUF4TOxDThXZEJpL4VcJWOV0/Y4eSDNNhOtBKfGMoo9EBCfLwevM
q6EyapSjiDz0pu9jUN/P
=V4y2
-----END PGP SIGNATURE-----
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull misc SPI device driver bug fixes from Grant Likely.
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi/spi-bfin5xx: Fix flush of last bit after each spi transfer
spi/spi-bfin5xx: fix reversed if condition in interrupt mode
spi/spi_bfin_sport: drop bits_per_word from client data
spi/bfin_spi: drop bits_per_word from client data
spi/spi-bfin-sport: move word length setup to transfer handler
spi/bfin5xx: rename config macro name for bfin5xx spi controller driver
spi/pl022: Allow request for higher frequency than maximum possible
spi/bcm63xx: set master driver mode_bits.
spi/bcm63xx: don't use the stopping state
spi/bcm63xx: convert to the pump message infrastructure
spi/spi-ep93xx.c: use dma_transfer_direction instead of dma_data_direction
spi: fix spi.h kernel-doc warning
spi/pl022: Fix calculate_effective_freq()
spi/pl022: Fix range checking for bits per word
Pull drm fixes from Dave Airlie:
"For your Friday pull request stack, nothing astounding or shattering
this week some exynos, some intel, some radeon fixes. One intel fix
for a regression somwehere back in 2.6.35 land."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: use frac fb div on APUs
drm/radeon: add a missing entry to encoder_names
drm/i915: handle input/output sdvo timings separately in mode_set
drm/i915: fix integer overflow in i915_gem_do_execbuffer()
drm/i915: fix integer overflow in i915_gem_execbuffer2()
drm/exynos: added missed vm area region mapping type.
drm/exynos: fixed exynos_drm_gem_map_pages bug.
drm/exynos: fixed duplicatd memory allocation bug.
drm/i915: fixup load-detect on enabled, but not active pipe
Pull x86 fixes from Ingo Molnar.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Use x2apic physical mode based on FADT setting
x86/mrst: Quiet sparse noise about plain integer as NULL pointer
x86, intel_cacheinfo: Fix error return code in amd_set_l3_disable_slot()
Pull perf fixes from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix perf_event_for_each() to use sibling
perf symbols: Read plt symbols from proper symtab_type binary
tracing: Fix stacktrace of latency tracers (irqsoff and friends)
perf tools: Add 'G' and 'H' modifiers to event parsing
tracing: Fix regression with tracing_on
perf tools: Drop CROSS_COMPILE from flex and bison calls
perf report: Fix crash showing warning related to kernel maps
tracing: Fix build breakage without CONFIG_PERF_EVENTS (again)
Pull build fixes for less mainstream architectures from Paul Gortmaker:
"These are fixes for frv(1), blackfin(2), powerpc(1) and xtensa(4).
Fortunately the touches are nearly all specific to files just used by
the arch in question. The two touches to shared/common files
[kernel/irq/debug.h and drivers/pci/Makefile] are trivial to assess as
no risk to anyone.
Half of them relate to xtensa directly. It was only when I fixed the
last xtensa issue that I realized that the arch has been broken for a
significant time, and isn't a specific v3.4 regression. So if you
wanted, we could leave xtensa lying bleeding in the street for a
couple more weeks and queue those for 3.5. But given they are no risk
to anyone outside of xtensa, I figured to just leave them in.
If you are OK with taking the xtensa fixes, then please pull to get:
- one last implicit include uncovered by system.h that is in a file
specific to just one powerpc defconfig. (I'd sync'd with BenH).
- fix an oversight in the PCI makefile where shared code wasn't being
compiled for ARCH=frv
- fix a missing include for GPIO in blackfin framebuffer.
- audit and tag endif in blackfin ezkit board file, in order to find
and fix the misplaced endif masking a block of code.
- fix irq/debug.h choice of temporary macro names to be more internal
so they don't conflict with names used by xtensa.
- fix a reference to an undeclared local var in xtensa's signal.c
- fix an implicit bug.h usage in xtensa's asm/io.h uncovered by my
removing bug.h from kernel.h
- fix xtensa to properly indicate it is using asm-generic/hardirq.h
in order to resolve the link error - undefined ack_bad_irq
The xtensa still fails final link as my latest binutils does something
evil when ld forward-relocates unlikely() blocks, but in theory people
who have older/valid toolchains could now use the thing."
* 'for-v3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
xtensa: fix build fail on undefined ack_bad_irq
blackfin: fix ifdef fustercluck in mach-bf538/boards/ezkit.c
blackfin: fix compile error in bfin-lq035q1-fb.c
pci: frv architecture needs generic setup-bus infrastructure
irq: hide debug macros so they don't collide with others.
xtensa: fix build error in xtensa/include/asm/io.h
xtensa: fix build failure in xtensa/kernel/signal.c
powerpc: fix system.h fallout in sysdev/scom.c [chroma_defconfig]
Pull security key doc update from Jeff Layton:
"Ordinarily, I send my patches through others' trees, but David
suggested I just send this one to you directly since it's just a
Documentation/ update"
* 'docs-3.4' of git://git.samba.org/jlayton/linux:
keys: update the documentation with info about "logon" keys
In xen_restore_fl_direct(), xen_force_evtchn_callback() was being
called even if no events were pending. This resulted in (depending on
workload) about a 100 times as many xen_version hypercalls as
necessary.
Fix this by correcting the sense of the conditional jump.
This seems to give a significant performance benefit for some
workloads.
There is some subtle tricksy "..since the check here is trying to
check both pending and masked in a single cmpw, but I think this is
correct. It will call check_events now only when the combined
mask+pending word is 0x0001 (aka unmasked, pending)." (Ian)
CC: stable@kernel.org
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We're spending huge amounts of time on lock contention during
end_io processing because we unconditionally assume we are overwriting
an existing extent in the file for each IO.
This checks to see if we are outside i_size, and if so, it uses a
less expensive readonly search of the btree to look for existing
extents.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Btrfs has an optimization where it will preallocate dentries during
readdir to fill in enough information to open the inode without an extra
lookup.
But, we're calling d_alloc, which is doing GFP_KERNEL allocations, and
that leads to deadlocks because our readdir code has tree locks held.
For now, disable this optimization. We'll fix the gfp mask in the next
merge window.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This patch ensures that the last bit of a transfer gets correctly
flushed out of the register.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This condition is used to determine 8 bits or 16 and 32 bits transfer.
Obviously it is reversed.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Since the member was dropped from the common Blackfin header, we need
to stop using it in the SPORT driver too.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
No other SPI controller has this field, and SPI clients should be setting
this up in their own drivers. So drop it from the Blackfin controller to
keep people from using it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Each transfer may have its own bits per word.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This controller is only for blackfin 5xx soc, so rename it to BFIN5XX
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently, if we request for frequency greater than maximum possible, spi driver
returns error.
For example, if the spi block src frequency is 333/4 MHz, i.e. 83.33.. MHz,
maximum frequency programmable would be src/2. Which would come around 41.6...
It is difficult to pass frequency in these figures. We normally try to program
in round figures, like 42 MHz and it should get programmed to <=
requested_frequency, i.e. 41.6...
For this to happen, we must not return error even if requested freq is higher
than max possible. But should program it to max possible.
Reported-by: Vinit Kamalaksha Shenoy <vinit.shenoy@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix out-of-space checking, addressing a warning and potential resource
leak when resizing the filesystem down while allocating blocks.
Signed-off-by: Daniel J Blueman <daniel@quora.org>
Reviewed-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
may_commit_transaction() calls
spin_lock(&space_info->lock);
spin_lock(&delayed_rsv->lock);
and update_global_block_rsv() calls
spin_lock(&block_rsv->lock);
spin_lock(&sinfo->lock);
Lockdep complains about this at run time.
Everywhere except in update_global_block_rsv(), the space_info lock is
the outer lock, therefore the locking order in update_global_block_rsv()
is changed.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
I was seeing root_list corruption on unmount during fs resize in 3.4-rc4; add
correct locking to address this.
Signed-off-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_map_block sets mirror_num, so that the repair code knows eventually
which device gave us the read error. For RAID10, mirror_num must be 1 or 2.
Before this fix mirror_num was incorrectly related to our stripe index.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_start_delalloc_inodes will just walk the list of delalloc inodes and
start writing them out, but it doesn't splice the list or anything so as
long as somebody is doing work on the box you could end up in this section
_forever_. So just remove it, it's not needed anyway since sync will start
writeback on all inodes anyway, all we need to do is wait for ordered
extents and then we can commit the transaction. In my horrible torture test
sync goes from taking 4 minutes to about 1.5 minutes. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
We were not properly advertising the MODE bits supported by this driver, fix
that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
NeilBrown
Shaohua Li
Jonathan Brassow
Linus Torvalds
Marcos Paulo de Souza
Kenneth Graunke
Alex Deucher
David Vrabel
Chris Mason
Scott Jiang
Viresh Kumar
Daniel J Blueman
Stefan Behrens
Jan Schmidt
Josef Bacik
Florian Fainelli