Add the missing unlock before return from function serial8250_register_8250_port()
in the error handling case.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20190703055908.141294-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds a flush of RX and TX FIFOs, and fixes some errors:
- adds RX FIFO flush in startup fonction
- removes the useless transmitter enabling in startup fonction
(e.g. receiver only, see Documentation/serial/driver)
- configures FIFO threshold before enabling it, rather than after
- flushes both TX and RX in set_termios function
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds the support of RX FIFO threshold in order to improve the RX FIFO
management.
This is done by enabling fifo threshold interrupt, instead of relying
on rx empty/fifo not full irq. That basically generates one irq/char
currently. With this patch:
- RXCFG is set to half fifo size (e.g. 16/2 = 8 data for a 16 data depth
FIFO)
- irq rate may be reduced by up to 1/RXCFG, e.g. 1 over 8 with current
RXCFG setting.
- Receiver timeout is used to gather chars when FIFO threshold isn't
reached.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds the support of TX FIFO threshold in order to improve the TX FIFO
management:
- TX FIFO threshold irq enabling (instead of relying on tx empty / fifo
not full irq that generates one irq/char)
- TXCFG is set to half fifo size (e.g. 16/2 = 8 data for a 16 data depth
FIFO)
- irq rate may be reduced by up to 1/TXCFG, e.g. 1 over 8 with current
TXCFG setting.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improves PIO transmission:
- Replaces the FIFO filling per character by a filling per blocks of
characters, which provides better performances
- Replaces the active waiting loop by TX empty interrupt dynamic handling.
TXE interrupt is now enabled when data has to be sent (ie when
uart_circ is not empty), and inhibited when there is no more data to
send (ie when uart_circ is empty).
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support of RX timeout interrupts to limit the number of interrupts.
RX timeout is a number of bits (baud clock cycles) without
transmission seen in the receiver. One character is used as an arbitrary
RX timeout value.
If parity is enabled, the number of bits has to include parity bit.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2e9fe53910.
Reading LSR unconditionally but processing the error flags only if
UART_IIR_RDI bit was set before in IIR may lead to a loss of transmission
error information on UARTs where the transmission error flags are cleared
by a read of LSR. Information are lost in case an error is detected right
before the read of LSR while processing e.g. an UART_IIR_THRI interrupt.
Signed-off-by: Oliver Barta <o.barta89@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: 2e9fe53910 ("serial: 8250: Don't service RX FIFO if interrupts are disabled")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch permits the usage for GPIOs to control
the CTS/RTS/DTR/DSR/DCD/RI signals.
Changed by Stefan:
Only call mctrl_gpio_init(), if the device has no ACPI companion device
to not break existing ACPI based systems. Also only use the mctrl_gpio_
functions when "gpios" is available.
Use MSR / MCR <-> TIOCM wrapper functions.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a check for the GPIOs property existence, before the
GPIO is requested. This fixes an issue seen when the 8250 mctrl_gpio
support is added (2nd patch in this patch series) on x86 platforms using
ACPI.
Here Mika's comments from 2016-08-09:
"
I noticed that with v4.8-rc1 serial console of some of our Broxton
systems does not work properly anymore. I'm able to see output but input
does not work.
I bisected it down to commit 4ef03d3287
("tty/serial/8250: use mctrl_gpio helpers").
The reason why it fails is that in ACPI we do not have names for GPIOs
(except when _DSD is used) so we use the "idx" to index into _CRS GPIO
resources. Now mctrl_gpio_init_noauto() goes through a list of GPIOs
calling devm_gpiod_get_index_optional() passing "idx" of 0 for each. The
UART device in Broxton has following (simplified) ACPI description:
Device (URT4)
{
...
Name (_CRS, ResourceTemplate () {
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO0", 0x00, ResourceConsumer)
{
0x003A
}
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionOutputOnly,
"\\_SB.GPO0", 0x00, ResourceConsumer)
{
0x003D
}
})
In this case it finds the first GPIO (0x003A which happens to be RX pin
for that UART), turns it into GPIO which then breaks input for the UART
device. This also breaks systems with bluetooth connected to UART (those
typically have some GPIOs in their _CRS).
Any ideas how to fix this?
We cannot just drop the _CRS index lookup fallback because that would
break many existing machines out there so maybe we can limit this to
only DT enabled machines. Or alternatively probe if the property first
exists before trying to acquire the GPIOs (using
device_property_present()).
"
This patch implements the fix suggested by Mika in his statement above.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bug was introduced by commit b3b5764618 ("tty: serial_core: convert
uart_open to use tty_port_open"). It caused a constant warning printed
into the system log regarding the tty and port counter mismatch:
[ 21.644197] ttyS ttySx: tty_port_close_start: tty->count = 1 port count = 2
in case if session hangup was detected so the warning is printed starting
from the second open-close iteration.
Particularly the problem was discovered in situation when there is a
serial tty device without hardware back-end being setup. It is considered
by the tty-serial subsystems as a hardware problem with session hang up.
In this case uart_startup() will return a positive value with TTY_IO_ERROR
flag set in corresponding tty_struct instance. The same value will get
passed to be returned from the activate() callback and then being returned
from tty_port_open(). But since in this case tty_port_block_til_ready()
isn't called the TTY_PORT_ACTIVE flag isn't set (while the method had been
called before tty_port_open conversion was introduced and the rest of the
subsystem code expected the bit being set in this case), which prevents the
uart_hangup() method to perform any cleanups including the tty port
counter setting to zero. So the next attempt to open/close the tty device
will discover the counters mismatch.
In order to fix the problem we need to manually set the TTY_PORT_ACTIVE
flag in case if uart_startup() returned a positive value. In this case
the hang up procedure will perform a full set of cleanup actions including
the port ref-counter resetting.
Fixes: b3b5764618 "tty: serial_core: convert uart_open to use tty_port_open"
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds wrapper functions to convert MSR <-> TIOCM and also
MCR <-> TIOCM. These functions are used now in serial8250_do_set_mctrl()
and serial8250_do_get_mctrl().
Signed-off-by: Stefan Roese <sr@denx.de>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Factor out similar code pieces that set or clear UART_IER_THRI bit to
serial8250_{set,clear}_THRI() helpers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to add an out-of-memory error message inside
the driver because the core MM code will take care of it.
Remove the unneeded OOM error message.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to call return at the end of function which should
return void.
The patch is also remove one checkpatch warning:
WARNING: void function return statements are not generally useful
+ return;
+}
Fixes: 6ee04c6c54 ("tty: xuartps: Add polled mode support for xuartps")
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes this checkpatch warning:
WARNING: macros should not use a trailing semicolon
+#define to_cdns_uart(_nb) container_of(_nb, struct cdns_uart, \
+ clk_rate_change_nb);
Fixes: d9bb3fb126 ("tty: xuartps: Rebrand driver as Cadence UART")
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let kernel to find out major number dynamically for the first device and
then reuse it for other instances.
This fixes the issue that each uart is registered with a
different major number.
After the patch:
crw------- 1 root root 253, 0 Jun 10 08:31 /dev/ttyPS0
crw--w---- 1 root root 253, 1 Jan 1 1970 /dev/ttyPS1
Fixes: 024ca329bf ("serial: uartps: Register own uart console and driver structures")
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Pericom chips can achieve additional baud rates by programming the
sample clock register. The baud rates can be described as
921600 * 16 / (16 - scr) for scr values 5 to 15. The divisor is set to 1
for these baud rates.
Adds new quirk for Pericom chips other than the four port chips to use
the
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx_uart_set_termios() called imx_uart_rts_active(), or
imx_uart_rts_inactive() before taking port->port.lock.
As a consequence, sport->port.mctrl that these functions modify
could have been changed without holding port->port.lock.
Moved locking of port->port.lock above the calls to fix the issue.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c70669ecef as it
breaks the build.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Bich Hemon <bich.hemon@st.com>
Cc: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function msm_wait_for_xmitr can be taken with interrupts
disabled. In order to avoid a potential system lockup - demonstrated
under stress testing conditions on SoC QCS404/5 - make sure we wait
for a bounded amount of time.
Tested on SoC QCS404.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interrupt handler checked THRE bit (transmitter holding register
empty) in LSR to detect if TX fifo is empty.
In case when there is only receive interrupts the TX handling
got called because THRE bit in LSR is set when there is no
transmission (FIFO empty). TX handling caused TX stop, which in
RS-485 half-duplex mode actually resets receiver FIFO. This is not
desired during reception because of possible data loss.
The fix is to check if THRI is set in IER in addition of the TX
fifo status. THRI in IER is set when TX is started and cleared
when TX is stopped.
This ensures that TX handling is only called when there is really
transmission on going and an interrupt for THRE and not when there
are only RX interrupts.
Signed-off-by: Kimmo Rautkoski <ext-kimmo.rautkoski@vaisala.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove spin_lock_irqsave in stm32_config_rs485, it cause recursive locking.
Already locked in uart_set_rs485_config.
Fixes: 1bcda09d29 ("serial: stm32: add support for RS485 hardware control mode")
Signed-off-by: Borut Seljak <borut.seljak@t-2.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Deferred probe is an expected return value for clk_get() on many
platforms. The driver deals with it properly, so there's no need
to output a warning that may potentially confuse users.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_info() is more appropriate for printing messages inside drivers, so
switch to dev_info().
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_info() is more appropriate for printing messages inside drivers, so
switch to dev_info().
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to support Rx in-band wakeup, we need to enable irq wake on an
edge sensitive interrupt of Rx pin before suspend and disable it when
resuming.
This interrupt is used only as wake source to resume the system when
suspended. Note that the sent character will be lost as the controller is
actually suspended.
We use this to support wakeup on bluetooth. Bluetooth will repeatedly send
0xFD to wakeup host. Once host detects Rx falling, an interrupt is
triggered, and the system leaves sleep state. Then, the bluetooth driver
will send 0xFC to bluetooth and bluetooth can start to send normal HCI
packets.
Signed-off-by: Claire Chang <tientzu@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the cable is not connected then the target gets into
an infinite wait for tx empty.
Add a timeout to the tx empty wait.
Reported-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we are doing a read of the status register.
Move the spinlock after that as the reads need not be spinlock
protected. This patch prevents relaxing the cpu with spinlock held.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When modprobe/rmmod/modprobe module, if platform_driver_register() fails,
the kernel complained,
proc_dir_entry 'driver/digicolor-usart' already registered
WARNING: CPU: 1 PID: 5636 at fs/proc/generic.c:360 proc_register+0x19d/0x270
Fix this by adding uart_unregister_driver() when platform_driver_register() fails.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix sparse warning:
drivers/tty/serial/stm32-usart.c:603:14: warning:
symbol 'stm32_get_databits' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Select either pinctrl sleep state in suspend function or default state in
resume function.
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 84ecc2f6eb.
con_insert_unipair() is working with a sparse 3-dimensional array:
- p->uni_pgdir[] is the top layer
- p1 points to a middle layer
- p2 points to a bottom layer
If it needs to allocate a new middle layer, and then fails to allocate
a new bottom layer, it would previously free only p2, and now it frees
both p1 and p2. But since the new middle layer was already registered
in the top layer, it was not leaked.
However, if it looks up an *existing* middle layer and then fails to
allocate a bottom layer, it now frees both p1 and p2 but does *not*
free any other bottom layers under p1. So it *introduces* a memory
leak.
The error path also cleared the wrong index in p->uni_pgdir[],
introducing a use-after-free.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 84ecc2f6eb ("consolemap: Fix a memory leaking bug in drivers/tty/vt/consolemap.c")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull x86 fixes from Ingo Molnar:
"Two fixes: a quirk for KVM guests running on certain AMD CPUs, and a
KASAN related build fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/CPU/AMD: Don't force the CPB cap when running under a hypervisor
x86/boot: Provide KASAN compatible aliases for string routines
Pull perf fixes from Ingo Molnar:
"On the kernel side there's a bunch of ring-buffer ordering fixes for a
reproducible bug, plus a PEBS constraints regression fix.
Plus tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools headers UAPI: Sync kvm.h headers with the kernel sources
perf record: Fix s390 missing module symbol and warning for non-root users
perf machine: Read also the end of the kernel
perf test vmlinux-kallsyms: Ignore aliases to _etext when searching on kallsyms
perf session: Add missing swap ops for namespace events
perf namespace: Protect reading thread's namespace
tools headers UAPI: Sync drm/drm.h with the kernel
tools headers UAPI: Sync drm/i915_drm.h with the kernel
tools headers UAPI: Sync linux/fs.h with the kernel
tools headers UAPI: Sync linux/sched.h with the kernel
tools arch x86: Sync asm/cpufeatures.h with the with the kernel
tools include UAPI: Update copy of files related to new fspick, fsmount, fsconfig, fsopen, move_mount and open_tree syscalls
perf arm64: Fix mksyscalltbl when system kernel headers are ahead of the kernel
perf data: Fix 'strncat may truncate' build failure with recent gcc
perf/ring-buffer: Use regular variables for nesting
perf/ring-buffer: Always use {READ,WRITE}_ONCE() for rb->user_page data
perf/ring_buffer: Add ordering to rb->nest increment
perf/ring_buffer: Fix exposing a temporarily decreased data_head
perf/x86/intel/ds: Fix EVENT vs. UEVENT PEBS constraints
Pull EFI fixes from Ingo Molnar:
"Two EFI fixes: a quirk for weird systabs, plus add more robust error
handling in the old 1:1 mapping code"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Allow the number of EFI configuration tables entries to be zero
efi/x86/Add missing error handling to old_memmap 1:1 mapping code
Here are just two small patches, that fix up some found SPDX identifier
issues.
The first patch fixes an error in a previous SPDX fixup patch, that
causes build errors when doing 'make clean' on the tree (the fact that
almost no one noticed it reflects the fact that kernel developers don't
like doing that option very often...)
The second patch fixes up a number of places in the tree where people
mistyped the string "SPDX-License-Identifier". Given that people can
not even type their own name all the time without mistakes, this was
bound to happen, and odds are, we will have to add some type of check
for this to checkpatch.pl to catch this happening in the future.
Both of these have passed testing by 0-day.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPNuiQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymt4ACgmqgJ5qJFr5UC/XLauYpl5IDXvH0AnjEgUb4h
RQSKj2wjMzGpBYheamtx
=tI3h
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull SPDX fixes from Greg KH:
"Here are just two small patches, that fix up some found SPDX
identifier issues.
The first patch fixes an error in a previous SPDX fixup patch, that
causes build errors when doing 'make clean' on the tree (the fact that
almost no one noticed it reflects the fact that kernel developers
don't like doing that option very often...)
The second patch fixes up a number of places in the tree where people
mistyped the string "SPDX-License-Identifier". Given that people can
not even type their own name all the time without mistakes, this was
bound to happen, and odds are, we will have to add some type of check
for this to checkpatch.pl to catch this happening in the future.
Both of these have passed testing by 0-day"
* tag 'spdx-5.2-rc3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
treewide: fix typos of SPDX-License-Identifier
crypto: ux500 - fix license comment syntax error
A minor fix to our IMC PMU code to print a less confusing error message when the
driver can't initialise properly.
A fix for a bug where a user requesting an unsupported branch sampling filter
can corrupt PMU state, preventing the PMU from counting properly.
And finally a fix for a bug in our support for kexec_file_load(), which
prevented loading a kernel and initramfs. Most versions of kexec don't yet use
kexec_file_load().
Thanks to:
Anju T Sudhakar, Dave Young, Madhavan Srinivasan, Ravi Bangoria, Thiago Jung
Bauermann.
-----BEGIN PGP SIGNATURE-----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=ilhV
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A minor fix to our IMC PMU code to print a less confusing error
message when the driver can't initialise properly.
A fix for a bug where a user requesting an unsupported branch sampling
filter can corrupt PMU state, preventing the PMU from counting
properly.
And finally a fix for a bug in our support for kexec_file_load(),
which prevented loading a kernel and initramfs. Most versions of kexec
don't yet use kexec_file_load().
Thanks to: Anju T Sudhakar, Dave Young, Madhavan Srinivasan, Ravi
Bangoria, Thiago Jung Bauermann"
* tag 'powerpc-5.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/kexec: Fix loading of kernel + initramfs with kexec_file_load()
powerpc/perf: Fix MMCRA corruption by bhrb_filter
powerpc/powernv: Return for invalid IMC domain
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJc85ibAAoJEL/70l94x66D72gH/iaXjRF9uqGSnd1/JLHIawfb
oH0VQS24tBzRlFREBTA68IxThgjTmSS+yHcAXSO7JmxztjGq3ZWiNaidQIvC1reu
t4MJMvf7ZZa7Yq0OAy2jwVAkZMKk5P8hBjjI5N7pEBb4ApJHzsCHV+KEIe5loc+q
f5LYLR53keImJ40wxh/qFftNNlYJUMv6tWa8y0mrlBrKABOvdRYFswhqcnEPibi9
cPoHDS6Ep/34eAVQzqHzfDbjezpa342SSw6s66Vpb/qYJyxoUh1Mw+9YCmAWanS8
vuvXz4qjCFvLRrmc9ctASUTEVydqx8IdcKQGiteWgpSrl4kgy6nLMZDY5sbq8UM=
=Bgfn
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Fixes for PPC and s390"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Book3S HV: Restore SPRG3 in kvmhv_p9_guest_entry()
KVM: PPC: Book3S HV: Fix lockdep warning when entering guest on POWER9
KVM: PPC: Book3S HV: XIVE: Fix page offset when clearing ESB pages
KVM: PPC: Book3S HV: XIVE: Take the srcu read lock when accessing memslots
KVM: PPC: Book3S HV: XIVE: Do not clear IRQ data of passthrough interrupts
KVM: PPC: Book3S HV: XIVE: Introduce a new mutex for the XIVE device
KVM: PPC: Book3S HV: XIVE: Fix the enforced limit on the vCPU identifier
KVM: PPC: Book3S HV: XIVE: Do not test the EQ flag validity when resetting
KVM: PPC: Book3S HV: XIVE: Clear file mapping when device is released
KVM: PPC: Book3S HV: Don't take kvm->lock around kvm_for_each_vcpu
KVM: PPC: Book3S: Use new mutex to synchronize access to rtas token list
KVM: PPC: Book3S HV: Use new mutex to synchronize MMU setup
KVM: PPC: Book3S HV: Avoid touching arch.mmu_ready in XIVE release functions
KVM: s390: Do not report unusabled IDs via KVM_CAP_MAX_VCPU_ID
kvm: fix compile on s390 part 2
Pull i2c fixes from Wolfram Sang:
"A memleak fix for the core, two driver bugfixes, as well as fixing
missing file patterns to MAINTAINERS"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add I2C DT bindings to ARM platforms
MAINTAINERS: add DT bindings to i2c drivers
i2c: synquacer: fix synquacer_i2c_doxfer() return value
i2c: mlxcpld: Fix wrong initialization order in probe
i2c: dev: fix potential memory leak in i2cdev_ioctl_rdwr
Pull thermal SoC fix from Eduardo Valentin:
"A single revert, detected to cause issues on the tsens driver"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
Revert "drivers: thermal: tsens: Add new operation to check if a sensor is enabled"
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXPKwKQAKCRBiEGxRG/Sl
223/AQCEPqJrBOFz8Gvq+NUX14YGHTvdkzLlivkFbpOLB18REAEAyTQPJYEr4nha
lZQdHMB6HaphiHQN/rxqwq0kyWQQKQQ=
=5ID/
-----END PGP SIGNATURE-----
Merge tag 'led-fixes-for-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fix from Jacek Anaszewski:
"Fix for a recent change in LED core, that didn't take into account the
possibility of calling led_blink_setup() from atomic context"
* tag 'led-fixes-for-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: avoid flush_work in atomic context
Wei Yongjun
Erwan Le Ray
Oliver Barta
Yegor Yefremov
Stefan Roese
kbuild test robot
Serge Semin
Andy Shevchenko
Fabio Estevam
Nava kishore Manne
Shubhrajyoti Datta
Jay Dolan
Sergey Organov
Greg Kroah-Hartman
Jorge Ramirez-Ortiz
Rautkoski Kimmo EXT
Borut Seljak
Thierry Reding
Claire Chang
Long Cheng
Kefeng Wang
YueHaibing
Bich Hemon
Ben Hutchings
Linus Torvalds