This is the initial implementation of the new OGM protocol
(version 2). It has been designed to work on top of the
newly added ELP.
In the previous version the OGM protocol was used to both
measure link qualities and flood the network with the metric
information. In this version the protocol is in charge of
the latter task only, leaving the former to ELP.
This means being able to decouple the interval used by the
neighbor discovery from the OGM broadcasting, which revealed
to be costly in dense networks and needed to be relaxed so
leading to a less responsive routing protocol.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This parameter can be set individually on each interface and
allows the configuration of the elp interval for the link
quality measurements during runtime. Usually it is desirable
to set it to a higher (= slower) value on interfaces which
have a more static characteristic (e.g. wired interfaces)
or very dense neighbourhoods to reduce overhead.
Developed by Linus during a 6 months trainee study period in
Ascom (Switzerland) AG.
Signed-off-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
[antonio@open-mesh.com: respin on top of the latest master]
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Initially developed by Linus during a 6 months trainee study
period in Ascom (Switzerland) AG.
Signed-off-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
The B.A.T.M.A.N. protocol originally only used a single
message type (called OGM) to determine the link qualities to
the direct neighbors and spreading these link quality
information through the whole mesh. This procedure is
summarized on the BATMAN concept page and explained in
details in the RFC draft published in 2008.
This approach was chosen for its simplicity during the
protocol design phase and the implementation. However, it
also bears some drawbacks:
* Wireless interfaces usually come with some packet loss,
therefore a higher broadcast rate is desirable to allow
a fast reaction on flaky connections.
Other interfaces of the same host might be connected to
Ethernet LANs / VPNs / etc which rarely exhibit packet
loss would benefit from a lower broadcast rate to reduce
overhead.
* It generally is more desirable to detect local link
quality changes at a faster rate than propagating all
these changes through the entire mesh (the far end of
the mesh does not need to care about local link quality
changes that much). Other optimizations strategies, like
reducing overhead, might be possible if OGMs weren't
used for all tasks in the mesh at the same time.
As a result detecting local link qualities shall be handled
by an independent message type, ELP, whereas the OGM message
type remains responsible for flooding the mesh with these
link quality information and determining the overall path
transmit qualities.
Developed by Linus during a 6 months trainee study period in
Ascom (Switzerland) AG.
Signed-off-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
This allows us to easily add a sysfs parameter for an
unsigned int later, which is not for a batman mesh interface
(e.g. bat0), but for a common interface instead. It allows
reading and writing an atomic_t in hard_iface (instead of
bat_priv compared to the mesh variant).
Developed by Linus during a 6 months trainee study period in
Ascom (Switzerland) AG.
Signed-off-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
[antonio@open-mesh.com: rename functions and move macros]
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
In commit 5b6490def9 ("3c59x: Use setup_timer()") Amitoj
removed add_timer which sets up the epires timer. In this patch
the behavior is restore but it uses mod_timer which is a bit more
compact.
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Till today, the ucode consisted of two d0 images - regular,
in which the usniffer wasn't enabled, and usniffer, in which the
usniffer logs were enabled.
Lately, the two images were unified, so there is only one d0 image,
in which the usniffer logs are enabled.
Add new TLV capability for supporting the consolidated images
(set 2, bit 13).
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently when entering D3 with WOWLAN configured, we enable in the
configuration flags beacon storing, and do not disable beacon
filtering, and do not wake up from a magic packet.
Having both enabled is wrong (should not have both enabled),
and causes problems in the RX queues in the FW, causing
the FW not to recognize the magic packet when it comes.
Disable beacon storing in wowlan configuration.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
To ensure that the SNAP/TCP/IP headers are DW aligned, the firmware
may add 2-byte pad at the end of the mac header - after the IV, before
the SNAP.
In that case the mpdu descriptor pad bit will be turned on.
Driver should take it into consideration, and remove the padding before
passing the packet to mac80211. Do that.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Beacon abort (ba) is set while sending power command, but only
after at least one beacon_filter command was successfully sent.
If we heard a beacon before starting association, this order
is maintained and ba is properly set.
However, if the first beacon is received after association,
we send the power command upon association, configure the
beacon filtering when the first beacon arrives, and in that case,
beacon abort is not set.
So identify this, and send a power command post the beacon_filter
command if needed.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Older versions of the firmware don't support U-APSD for
P2P Client. Forbid U-APSD for P2P Client when an old
firmware is being used.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow to publish RRM capabilities without the need to support a minimal
capability set. Since some RRM features(e.g. neighbor report) are fw
independent, set this capability unconditionally.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
* Remove uneeded includes:
iwl-csr.h and devcoredump aren't used in mac80211.c.
* Remove uneeded empty line
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the device is in d0i3/d3 we will not receive the VHT
MU-MIMO group id management frame. Instead, firmware will
notify us upon exit on the current status and we can in turn
update mac80211. Support this notification.
While at it, also check as a precaution that the vif is indeed
the VHT MU-MIMO owner before updating the firmware.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Commit 69c7fda409 removed the
users of iwl_mvm_tid_data.reduced_tpc. Due to a conflict,
I forgot to commit the hunk that removed the field itself.
Do this know.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In multi rx queue HW, without execessive locking, there is no sync
between the ctrl path (default queue) and the rest of the rx queues.
This might cause issues on certain situations. For example, in case
a delBA was processed on a default queue but out of order packets
still wait for processing on the other queue.
The solution is to introduce internal messaging between the CTRL path
and the other rx queues.
The driver will send a message to the firmware, which will echo it to
all the requested queues. The message will be in order inside the queue.
This way we can avoid CTRL path and RSS queues races.
Add support for this messaging mechanism. As the firmware is agnostic to
the data sent, add internal representation of the data as well.
Although currently only delBA flow will use it, the internal representation
will enable generic use of this infrastructure for future uses.
Next patch will utilize this messaging mechanism for the reorder buffer
delBA flow.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Next hardware will direct TCP/UDP streams to different cores.
Packets belonging to the same stream will be directed to the same
core.
The result is that duplicates will be always directed to the same
rx queue were the first packet was received.
This enabled parallelizing the duplicate packet detection across
the different cores, without sharing data between the rx queues.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
With these ops, we can know when we are about to enter system suspend.
This allows us to exit D0i3 state before entering suspend.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fine tune RFH registers further:
* Set default queue explicitly
* Set RFH to drop frames exceeding RB size
* Set the maximum rx transfer size to DRAM to 128 instead of 64
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
During d0i3 frames might be filtered by the FW and this may
cause reordering buffer a delay - as the frames will not be
received and reorder will time out.
Introduce an API function to receive notification of filtered
frames and pass the information to the mac80211.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When forming IBSS, mac80211 scans in order to find an already
existing cell to join.
In case the scan does not find any existing cell a new IBSS
cell is formed.
When receiving the beacons of another IBSS cell we should
merge if the other IBSS cell's TSF is higher than ours.
However, currently iwlmvm does not set any timestamp flag in
rx_status so there is no valid rx timestamp to compare the
beacon's TSF to.
The reason for that is that TSF as indicated by the firmware
is at INA time, but up till now mac80211 expected the TSF at
the beginning or end of the MPDU.
Set the flag to the newly added RX_FLAG_MACTIME_PLCP_START flag.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Current iwlwifi_trace_dev_rx prints only the cmd without the
group, which might be misleading. Change it to print the wide
id. While at it add the DATA_PATH group and sub commands to the
trace of the command names, sine it is missing due to patches
submitted in parallel.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The A-MSDU must be smaller than the Transmit FIFO in the
device. Since the size of the TXF can change depending
on the device / firmware compilation mode, take the size
of the FIFO dynamically from the what the firmware tells us.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
in order to be able to tune the size of the desired A-MSDU
based on link condition, add a knob to modify the length
of the A-MSDU.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Now that PCIe knows how to create A-MSDUs, use this
capability and prepare SKBs that are large enough to
build an A-MSDU.
Advertise TSO support towards the network stack and
segment the packet with gso_size set to be the maximal
A-MSDU length (after having taken the headers to be added
into account) to make sure that the skb that is passed
down to the transport are not longer than the maximal
A-MSDU allowed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware handles the VHT MU-MIMO group data on its own.
However, on HW restart (and future sniffer mode) the driver
shall update the firmware on the VHT MU-MIMO group membership
status.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Incoming hardware will support VHT MU-MIMO. Declare this
capability for relevant hardware.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Working with MSIX requires prior configuration.
This includes requesting interrupt vectors from the OS,
registering the vectors and mapping the optional causes to the
relevant interrupt. In addition add new interrupt handler
to handle MSIX interrupt.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of waking up the device each time we write a
register, wake it up once, and writes the registers
at once.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Klocwork is unhappy as ht_vht_rates might be accessed with
rate->index being set to values between 0 and 3 which will
lead to accessing uninitialized array elements. Effectively this
doesn't happen as in HT/VHT we're not using these rate indices.
Still fix this.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware doesn't send match found notifications when no matchsets
are passed. This makes sense because if there are no matchsets,
nothing can be matched. But the nl80211 API should report when there
are results available, even if no matchsets were passed.
To handle this, we can use the firmware's ITERATION_COMPLETE
reporting, which will send us notifications every time it completed a
scheduled scan iteration. Then we can set a flag when we received
beacons and use that to report that results are available.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These are a few fixes for the current cycle.
3 out of the 5 patches fix a bugzilla.
* fix a race that users reported when we try to load the firmware
and the hardware rfkill interrupt triggers at the same time.
* Luca fixes a very visible bug in scheduled scan: our firmware
doesn't support scheduled scan with no profile configured and
the supplicant sometimes requests such scheduled scans.
* build system fix
* firmware name update for 8265
* typo fix in return value
The initialization and copying of the RSS secret key
should not use ARRAY_SIZE as we need to initialize a
dword array, and not a byte array.
Fix also the hook maximum write size to allow writing
a longer table - up to full indirection table size.
Fixes: 43413a975d06("iwlwifi: mvm: support rss queues configuration command")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The 9000 series uses a diffrent sized descriptor. Update the
relevant tracing field.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Register cooling device in order to have the Thermal
Manager handle the device's power budget according to the sent
notifications.
The interface adds a new thermal cooling device to
/sys/class/thermal/ folder.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Register to thermal_zone interface and implement the
thermal ops.
The thermal handles the device throttling, and sets the
the temperature thresholds the Thermal Manager would be
notified of crossing.
The thermal interface adds a new thermal zone device sensor
under /sys/class/thermal/ folder.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Up to today the driver was notified of the temperature from the FW
and decided whether to enter CT-kill or not.
From now on, the FW will decide when to enter CT-kill and will notify
the driver.
Add support for this notification.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We intended to return PTR_ERR() here instead of 1.
Fixes: 1f9993f682 ('rocker: fix a neigh entry leak issue')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2016-02-24
This series contains updates to e1000e, igb and igbvf.
Raanan provides updates for e1000e, first increases the ULP timer since it
now takes longer for the ULP exit to complete on Skylake. Fixes the
configuration of the internal hardware PHY clock gating mechanism, which was
causing packet loss due to mis configuring. Fixed additional ULP
configuration settings which were not being properly cleared after cable
connect in V-Pro capable systems. Added support for more i219 devices.
Takuma Ueba provides a fix for I210 where IPv6 autoconf test sometimes
fails due to DAD NS for link-local is not transmitted. To avoid this
issue, we need to wait until 1000BASE-T status register "Remote receiver
status OK".
Todd provides a patch to override EEPROM WoL settings for specific OEM
devices. Then renamed igb defines to be more generic, since the define
E1000_MRQC_ENABLE_RSS_4Q enables 4 and 8 queues depending on the part.
Roland Hii fixes an issue where only the half cycle time of less than or
equal to 70 millisecond uses the I210 clock output function. His patch
adds additional conditions when half cycle time is equal to 125 or 250 or
500 millisecond to use the clock output function.
Alex Duyck adds support for generic transmit checksums for igb and igbvf.
Jon Maxwell fixes an issues where customer applications are registering
and un-registering multicast addresses every few seconds which is leading
to many "Link is up" messages in the logs as a result of the
netif_carrier_off(netdev) in igbvf_msix_other(). So remove the
link is up message when registering multicast addresses.
Corinna Vinschen provides a fix for when switching off VLAN offloading on
i350, the VLAN interface becomes unusable.
Stefan Assmann updates the driver to use ndo_stop() instead of
dev_close() when running ethtool offline self test. Since dev_close()
causes IFF_UP to be cleared which will remove the interfaces routes
and some addresses.
v2: Dropped patches 6-10 in the original series. Patch 6-7 added support
for character device for AVB and based on community feedback, we do not
want to do this. Patches 8-10 provided fixes to the problematic code
added in patches 6 & 7. So all of them must go!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On reviewing the code I realized that GRE and UDP tunnels could cause a
kernel panic if we used GSO to segment a large UDP frame that was sent
through the tunnel with an outer checksum and hardware offloads were not
available.
In order to correct this we need to update the feature flags that are
passed to the skb_segment function so that in the event of UDP
fragmentation being requested for the inner header the segmentation
function will correctly generate the checksum for the payload if we cannot
segment the outer header.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net: l3mdev: Fix source address for unnumbered deployments
David Lamparter noted a use case where the source address selection fails
to pick an address from a VRF interface - unnumbered interfaces. The use
case has the VRF device as the VRF local loopback with addresses and
interfaces enslaved without an address themselves. e.g,
ip addr add 9.9.9.9/32 dev lo
ip link set lo up
ip link add name vrf0 type vrf table 101
ip rule add oif vrf0 table 101
ip rule add iif vrf0 table 101
ip link set vrf0 up
ip addr add 10.0.0.3/32 dev vrf0
ip link add name dummy2 type dummy
ip link set dummy2 master vrf0 up
--> note dummy2 has no address - unnumbered device
ip route add 10.2.2.2/32 dev dummy2 table 101
ip neigh add 10.2.2.2 dev dummy2 lladdr 02:00:00:00:00:02
ping to the 10.2.2.2 through the L3 domain:
$ ping -I vrf0 -c1 10.2.2.2
ping: Warning: source address might be selected on device other than vrf0.
PING 10.2.2.2 (10.2.2.2) from 9.9.9.9 vrf0: 56(84) bytes of data.
picks up the wrong address -- the one from 'lo' not vrf0. And from tcpdump:
12:57:29.449128 IP 9.9.9.9 > 10.2.2.2: ICMP echo request, id 2491, seq 1, length 64
This patch series changes address selection to only consider devices in
the same L3 domain and to use the VRF device as the L3 domains loopback.
$ ping -I vrf0 -c1 10.2.2.2
PING 10.2.2.2 (10.2.2.2) from 10.0.0.3 vrf0: 56(84) bytes of data.
From tcpdump:
12:59:25.096426 IP 10.0.0.3 > 10.2.2.2: ICMP echo request, id 2113, seq 1, length 64
Now the source address comes from vrf0.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When selecting an address in context of a VRF, the vrf master should be
preferred for address selection. If it isn't, the user has a hard time
getting the system to select to their preference - the code will pick
the address off the first in-VRF interface it can find, which on a
router could well be a non-routable address.
Signed-off-by: David Lamparter <equinox@diac24.net>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
[dsa: Fixed comment style and removed extra blank link ]
Signed-off-by: David S. Miller <davem@davemloft.net>
Antonio Quartulli
Linus Luessing
Stafford Horne
Golan Ben-Ami
Matti Gottlieb
Dmitry Tunin
Emmanuel Grumbach
Sara Sharon
Avri Altman
Beni Lev
Luca Coelho
Haim Dreyfuss
Eyal Shapira
Chaya Rachel Ivgi
Dan Carpenter
David S. Miller
Alexander Duyck
David Lamparter