Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to its documentation the is_powered_on_standby field of the
uda134x platform data is supposed to prevent the the driver from shutting
down the ADC and DAC in standby mode. This behavior was broken in commit
commit f0fba2ad1b ("ASoC: multi-component - ASoC Multi-Component Support")
almost 5 years ago and all the flag does now is cause the driver to go to
SND_SOC_BIAS_ON in probe, just for the ASoC core to put it back into
SND_SOC_BIAS_STANDBY right after probe.
Apparently the intended behavior has not been missed, so just remove
is_powered_on_standby from the platform data struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is right not left sidetone which goes to "DACR".
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 5fe5b767dc ("ASoC: dapm: Do not pretend to support controls for non
mixer/mux widgets") revealed ill-defined control in a route between
"STENL Mux" and DACs in max98090.c:
max98090 i2c-193C9890:00: Control not supported for path STENL Mux -> [NULL] -> DACL
max98090 i2c-193C9890:00: ASoC: no dapm match for STENL Mux --> NULL --> DACL
max98090 i2c-193C9890:00: ASoC: Failed to add route STENL Mux -> NULL -> DACL
max98090 i2c-193C9890:00: Control not supported for path STENL Mux -> [NULL] -> DACR
max98090 i2c-193C9890:00: ASoC: no dapm match for STENL Mux --> NULL --> DACR
max98090 i2c-193C9890:00: ASoC: Failed to add route STENL Mux -> NULL -> DACR
Since there is no control between "STENL Mux" and DACs the control name must
be NULL not "NULL".
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Commit e409dfbfcc ("ASoC: dapm: Add a few supply widget sanity checks")
broke digital microphone support in max98090.c:
max98090 i2c-193C9890:00: Conditional paths are not supported for supply widgets (DMICL_ENA -> [DMIC] -> DMIC Mux)
max98090 i2c-193C9890:00: ASoC: no dapm match for DMICL_ENA --> DMIC --> DMIC Mux
max98090 i2c-193C9890:00: ASoC: Failed to add route DMICL_ENA -> DMIC -> DMIC Mux
max98090 i2c-193C9890:00: Conditional paths are not supported for supply widgets (DMICR_ENA -> [DMIC] -> DMIC Mux)
max98090 i2c-193C9890:00: ASoC: no dapm match for DMICR_ENA --> DMIC --> DMIC Mux
max98090 i2c-193C9890:00: ASoC: Failed to add route DMICR_ENA -> DMIC -> DMIC Mux
Problem is partially caused by commit f69e3caa9e ("ASoC: max98090: Enable
both DMIC channels also when using mono configuration") which connects
"DMICL_ENA" and "DMICR_ENA" supply widgets to "DMIC Mux".
Fix the breakage by reverting f69e3caa9e and then by adding additional
"DMICR_ENA" to "DMICL" and "DMICL_ENA" to "DMICR" cross-connections. This
disconnects these supply widgets from the mux and makes sure that both DMIC
data channels are still enabled together.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/intel/sst/sst_acpi.c:135:26: sparse: symbol 'chv_platform_data' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Skip dpcm path checking for playback or capture, if corresponding FE
doesn't support playback or capture, or currently is not ready. It
can reduce the unnecessary cost to search connected widgets.
[Tweaked comments for clarity -- broonie]
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch add ACPI device ID and platform data for two Cherryview-based
platforms, Cherrytrail and Braswell. Also reuse mfld driver ops in sst driver.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add machine driver for two Intel Cherryview-based platforms, Cherrytrail and
Braswell, with RT5672 codec.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the device tree binding for the WM8960 codec, and modify the
driver to extract the platform data from device tree, if present.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure to always convert the firmware data to local endianness before
using it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: a35daac77a ("ASoC: sigmadsp: Add support for fw v2")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
To be able to read back data from the DSP parameter memory the register
range needs to be marked as readable. At the same time we do not want them
to e.g. appear in debugfs output so mark them as precious as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
While we are at it also replace dev_get_drvdata() with snd_soc_codec_get_drvdata().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the i2s_set_sysclk() callback we are currently clearing all bits
of the IISMOD register in i2s_set_sysclk. It's due to an incorrect
mask used for the AND operation which is introduced in commit
a5a56871f8 (ASoC: samsung:
add support for exynos7 I2S controller) and also adds the missing
break statement.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/intel/sst/sst_acpi.c:124:26: sparse: symbol 'byt_rvp_platform_data' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The safeload feature allows to load up to 5 parameter memory registers
atomically. This is helpful for switching between e.g. filter settings
without causing any glitches.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the v2 version of the SigmaDSP firmware file
format. The new format has support for having different program and
parameter settings for different samplerates. In addition it stores metadata
describing the firmware. This metadata includes the set of supported
samplerates which will be used to restrict the samplerates that can be
selected by userspace. Also included is information about the modifiable
parameters. Those will be exposed as ALSA controls so they can be changed at
runtime.
The new format is based on a binary type-length-value structure that makes
it both forward and backwards compatible.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The v2 file format of the SigmaDSP takes a more declarative style compared
to the imperative style of the v1 format. In addition some features that are
supported with v2 require the driver to keep state around for the firmware.
This requires a bit of restructuring of both the firmware loader itself and
the drivers making use of the firmware loader.
Instead of loading and executing the firmware in place when the DSP is
configured the firmware is now loaded at driver probe time. This is required
since the new firmware format will in addition to the firmware data itself
contain meta information describing the firmware and its requirements and
capabilities. Those will for example be used to restrict the supported
samplerates advertised by the driver to userspace to the list of samplerates
supported for the firmware.
This only does the restructuring required by the v2 format, but does not
yet add support for the new format itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The official firmware generation tool never emitted any SIGMA_ACTION_DELAY
instructions. Keeping support for it with the new restructured loader that
also supports v2 will be difficult, so drop support for it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure to check the version field of the firmware header to make sure to
not accidentally try to parse a firmware file with a different layout.
Trying to do so can result in loading invalid firmware code to the device.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For ACPI we missed to pm_runtime_enable() call which is required to tell PM
core that runtime on this device is enabled now. Since this is common to
both PCI and APCI move it out. Also for ACPI we do not require
pm_runtime_allow() call, so remove that
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the regmap conversion ac97_read/ac97_write are just simple wrappers
around snd_soc_read/snd_soc_write. Use those instead directly and remove the
wrappers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch converts the ad1980 driver to use regmap for its IO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some drivers (most notably the AC'97 drivers) do not have access to their
regmap struct when the component/codec is registered. For those drivers the
automatic regmap setup will not work and needs to be done manually,
typically from the component/CODEC drivers probe callback.
This patch adds a set of helper function to handle deferred regmap
initialization as well as early regmap tear-down.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the slow charge of the vref in the end of the power sequences
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Follow the gpio naming rule to rename the irq function.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many firmwares do not wait for the start bit before they begin
processing audio, whilst this is a bug on the firmware side there are
too many such firmwares in the wild to ignore the situation. This patch
moves the core enable to happen at same time as the start, the firmware
looses the ability to overlap its own startup with the audio path bring
up but we ensure that all firmwares behave.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: JS Park <aitdark.park@samsung.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
while building we were getting the following build warning:
Section mismatch in reference from the function rt286_i2c_probe()
to the variable .init.data:force_combo_jack_table
The function rt286_i2c_probe() references
the variable __initdata force_combo_jack_table.
This is often because rt286_i2c_probe lacks a __initdata
annotation or the annotation of force_combo_jack_table is wrong.
we were getting the warning as force_combo_jack_table was marked
with __initdata
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the ASoC core no longer needs a handle to the AC'97 device that is
associated with a CODEC we can remove it from the snd_soc_codec struct and
push it into the individual driver state structs like we do for other
communication buses. Doing so creates a clean separation between the AC'97
bus support and the ASoC core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Setting the ac97_control field on a CPU DAI tells the ASoC core that this
DAI in addition to audio data also transports control data to the CODEC.
This causes the core to suspend the DAI after the CODEC and resume it before
the CODEC so communication to the CODEC is still possible. This is not
necessarily something that is specific to AC'97 and can be used by other
buses with the same requirement. This patch renames the flag from
ac97_control to bus_control to make this explicit.
While we are at it also change the type from int to bool.
The following semantich patch was used for automatic conversion of the
drivers:
// <smpl>
@@
identifier drv;
@@
struct snd_soc_dai_driver drv = {
- .ac97_control
+ .bus_control
=
- 1
+ true
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is no longer necessary as there is no code anymore that uses this for
CODEC DAIs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We have all the information and dependencies we need to initialize and
register the device available in snd_soc_new_ac97_codec(). So there is no
need to delay the device registration until after the card itself as been
registered.
This makes the code significantly simpler and also makes it possible to use
the AC'97 device in the CODECs probe function. The later will be required to
be able to convert the AC'97 CODEC drivers to regmap.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This has no users since commit f0fba2ad1b ("ASoC: multi-component - ASoC
Multi-Component Support") which was almost 5 years ago. Given that this runs
after CODEC probe functions have been run it also doesn't seem to be that
useful.
So drop it altogether to make the code simpler.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
soc_{un,}register_ac97_codec() is just a simple wrapper around
soc_ac97_dev_{un,}register(). There is no need to split these up into two
different sets of functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We always pass soc_ac97_ops to snd_soc_new_ac97_codec(). So instead of
allocating a snd_ac97_bus in snd_soc_new_ac97_codec() just use a static one
that gets initialized when snd_soc_set_ac97_ops() is called.
Also drop the device number parameter from snd_soc_new_ac97_codec(). We
currently only support one device per bus and all drivers pass 0 for the
device number. And if we should ever support multiple devices per bus it
wouldn't be up to individual AC'97 device drivers to pick their number, but
rather either the AC'97 adapter driver or the core code will assign them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the AC'97 support is splattered all throughout soc-core.c. Some
parts are #ifdef'd some parts are not. This patch moves the AC'97 support to
its own file, this should make the code a bit more clearer and also makes it
possible to easily not compile it into the kernel when not needed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The memory that a struct device is contained in must not be freed except
from within the device's release callback. The ASoC code currently does not
adhere to this rule for the AC'97 device. This patch fixes it by moving the
freeing of the AC'97 to the release callback and splitting up the
registration and unregistration of the device into separate steps for
getting/putting the reference to the device and adding/removing it to the
device hierarchy.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mpc5200_dma overwrites the private_data field of the CODEC's AC'97
device with the DMA drivers private data, but never actually reads it again.
Given that the private_data field is supposed to be owned by the AC'97
driver, overwriting it may cause undefined behavior. This patch removes the
code that overwrites the field from the driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mpc5200_psc_ac97 driver puts a snd_ac97 device on the stack in the
driver probe function, initializes the private data member of the device and
the never uses the device again. It should be safe to remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fix following errors while "make htmldocs" on
linux-next-20141110.
Warning(.//sound/soc/soc-jack.c:126): No description found for
parameter 'zones'
Warning(.//sound/soc/soc-jack.c:126): Excess function parameter
'zone' description in 'snd_soc_jack_add_zones'
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current driver can also run in I2S master mode, so remove the old comment.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modify the default value of the MX-8E[4] to 1 for ASRC function. It could
prevent the pop noise with ASRC function.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following compilation warning:
Warning: 'rt5631_i2c_dt_ids' defined but not used - when DT is not used.
Signed-off-by: Claude Youn <claude.youn@gmail.com>
Signed-off-by: Krishna Mohan Dani <krishna.md@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should not free any buffers associated with writing out coefficients
to the DSP until all the async writes have completed. This patch updates
the out of memory path when allocating a new buffer to include a call to
regmap_async_complete.
Reported-by: JS Park <aitdark.park@samsung.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Change clk_enable/disable() calls to clk_prepare_enable() and
clk_disable_unrepapre().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ACPI device table will generate the driver module alias for
Intel audio devices enumerated from ACPI.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use vmalloc to allocate the buffer for firmware/coefficient download and
rely on the SPI core to split this up into DMA-able chunks. This should
give better performance and means we no longer need to manually split
the download into page size chunks to avoid allocating overly large
continuous memory regions.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patah separate bias level off to standby and off. The standby
level will provide the necessary power for JD and push button
functions.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the last ACPI module support which also uses core module like the PCI
part
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TS3A227E is an autonomous audio accessory detection and
configuration switch that detects 3-pole or 4-pole audio accessories
and configures internal switches to route the signals accordingly.
This chip also has built-in support for the new button standard
described in the Android "Wired audio headset specification" v1.0.
These buttons will be reported on the jack as buttons 0-3 mapped to
KEY_MEDIA, KEY_VOLUMEUP, KEY_VOLUMEDOWN, and KEY_VOICE_COMMAND.
This will be added as an aux_dev and have the jack passed in from the
machine driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On a mx28evk with a sgtl5000 codec we notice a loud 'click' sound to happen
5 seconds after the end of a playback.
The SMALL_POP bit should fix this, but its definition is incorrect:
according to the sgtl5000 manual it is bit 0 of CHIP_REF_CTRL register, not
bit 1.
Fix the definition accordingly and enable the bit as intended per the code
comment.
After applying this change, no loud 'click' sound is heard after playback
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch adds the ACPI match ID for rt5670/5672 codec.
So on Intel CherryTrail/Braswell platforms, the codec can be enumerated from
ACPI and depends on ACPI to get platform-specific info and power saving.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Reviewed-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to set extra register to avoid a recording issue in TDM
mode.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit a1253ef6d3 ("ASoC: cs42l51: split i2c from codec driver"),
the I2C part of the CS42L51 was moved to a separate file, but the
definition of the of_device_id array was left in the driver file
itself, no longer connected to the platform_driver structure using the
.of_match_table pointer.
This commit exports the of_device_id array in cs42l51, and uses it as
.of_match_able in cs42l51-i2c.c. This solution was suggested by Brian
Austin.
Fixes: a1253ef6d3 ("ASoC: cs42l51: split i2c from codec driver")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The new IPs supports a new lower frequency 768kHz DMIC operation
add support for this into the OSR control.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
An underrun (playback) event occurs when the serializer transfer
data from the XRBUF buffer to the XRSR shift register, but the
XRBUF hasn't been filled. Similarly, the overrun (capture) event
occurs when data from the XRSR shift register is transferred to
the XRBUF but it hasn't been read yet.
These events are handled as XRUN events that cause the pcm to stop.
The stream has to be explicitly restarted by the userspace which
ensures that after stopping/starting McASP the data transfer is
aligned with DMA. The other possibility was to internally stop and
start McASP without DMA even knowing about it.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Output driver has two parameters that can be configured to reduce
pop noise: power-on delay and ramp-up step time. Two new kcontrols
have been added to set these parameters.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is easier to find the relevant enums in the code. Use the
SOC_ENUM_*_DECL macro for the individual items.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove rt5645_clk_sel_put function since it is never used.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5672 is very similar to rt5670. Therefore we use one codec driver
to support both codecs. The difference between rt5670 and rt5672 is
there is some difference in their dapm routing table.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of registering the irq name with the driver name, it's better to pass
the device name so that we have a more explicit indication as to what saif
instance the irq is related:
$ cat /proc/interrupts
CPU0
...
214: 4 - 59 80042000.saif
215: 0 - 58 80046000.saif
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm8962 uses the snd_soc_codec mutex to protect the wm8962_dsp2_ena_put()
function from concurrent execution. This patch moves that lock to the driver
level. This will allow us to eventually remove the snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm8958 driver uses the snd_soc_codec mutex to protect the various
firmware pointers from concurrent assignment. This patch moves this lock to
the driver level. This will allow us to eventually remove the snd_soc_codec
mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm8903 uses the snd_soc_codec mutex to protect its deemph settings from
concurrent access. This patch moves this lock to the driver level. This will
allow us to eventually remove the snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm8731 uses the snd_soc_codec mutex to protect its deemph settings from
concurrent access. This patch moves this lock to the driver level. This will
allow us to eventually remove the snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm5102 driver currently uses the snd_soc_codec mutex to protect its
ultrasonic response settings from concurrent access. This patch moves this
lock to the driver level. This will allow us to eventually remove the
snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max98095 uses the snd_soc_codec mutex to protect against concurrent
access in some of its control put handlers. Move this mutex to the driver
level so we can eventually remove the snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ab8500 driver uses a driver specific lock to protect concurrent access
to some of the control put/get handlers and uses the snd_soc_codec mutex for
some others. This patch updates the driver to consistently use the driver
specific lock for all controls. This will allow us to eventually remove the
snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to cast the cpu_of_node or codec_of_node of the
dai_links when calling of_put_node.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Volume Ramp to Renesas sound driver.
amixer set "DVC Out" 100%
amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
amixer set "DVC Out Ramp" on
aplay xxx.wav &
amixer set "DVC Out" 80% // Volume Down
amixer set "DVC Out" 100% // Volume Up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Active slots count depends on the number of channels in the stream
and the number of active serializers. Each serializer will handle
at most the number of channels specified via 'tdm-slots' parameter
in DT.
There are two possible scenarios:
- Single serializer: channel count fits in the max slots supported by
McASP serializers, active slots is same as channel count
- Multiple serializers: channel count is bigger than max slots supported
by a serializer. Channel count determines how many serializers are
needed at their max slot count configuration
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In IIS (I2S, TDM, etc) mode the maximum number of allowed channels for
either direction can be:
number of serializers for the direction * tdm_slots.
This constraint applicable for the first stream, while consequent stream
should not have more channels then the first stream.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of validating the tdm_slots parameter every time at hw_params we
can do it once during probe. If the parameter is not valid (<2 or >32)
print an error and fix it up.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the bus is configured to have more BCLK then the data type demands we
need to use the rotation to move the data to correct place.
Reported-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In IIS mode the tx and rx configuration is symmetric, the BCLK and FSYNC is
shared.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas R-Car sound driver probe will be failed
if it try to use DMA mode and it couldn't use for some reasons.
But PIO mode works even though in such case.
This patch try to fallback to PIO mode if DMA mode probing was failed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas R-Car sound driver debug message
is using random format
(ex "ssi0: xxx" / "SSI0 xxx" / "ssi[0]: xxx")
and confusable timing
("xxx probe failed" and "xxx probed" are shown in same time)
This patch fixes these
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If probe fails then we need to call pm_runtime_disable() to balance
out the previous pm_runtime_enable() call.
Signed-off-by: Anil Kumar <anilk4.v@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With device tree, it is possible (and encouraged) to build N900
kernels without CONFIG_MACH_NOKIA_RX51. Update config file to enable
the driver build in this case.
This makes sound work on my n900 under 3.18-rc1.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
TDM support is achieved using DSP transfer mode and setting a
programmable offset which specifies where data begins with
respect to the frame sync.
It requires 256-clock mode if CODEC is master (not currently
supported in the driver). No additional dependency if CODEC
is slave.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new helper function snd_pcm_stop_xrun() to the standard sequnce
lock/snd_pcm_stop(XRUN)/unlock by a single call, and replace the
existing open codes with this helper.
The function checks the PCM running state to prevent setting the wrong
state, too, for more safety.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This function has no more non regmap user, which means we can remove the
implementation of the function and associated functions and structure
fields.
For convenience we keep a static inline version of the function that
forwards calls to regcache_sync() unconditionally.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
For convenience for drivers that do not want to keep their own pointer to
regmap struct around forward calls to snd_soc_cache_sync() to
regcache_sync() if the driver is using regmap. This is similar to what we do
for snd_soc_read()/snd_soc_write().
This patch also fixes drivers which already have been converted to regmap,
but still use snd_soc_cache_sync() for trying to the sync the cache.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm9712/wm9713 has separate mixers for the left and the right channel,
but the inputs to the mixers are enabled/disabled by the same control.
Currently this is implemented by the driver by registering two virtual
controls for each physical control, one for the left mixer and one for the
right mixer.
Using virtual registers will no longer work when the driver has
been converted to regmap. This patch converts the driver to use controls
with custom put/get callbacks instead which implement the logic making sure
that the physical control is unmuted when either the left or the right
control is unmuted.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
In DSP mode, the register r/w should use the specific function to access
that is invoked by address mapping of the DSP.
The MX-65[1] is for switching DSP or codec mode.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Exynos7 I2S controller has no internal dma, supports more
no. of root clock sampling frequencies and has more no.of Rx
fifos to support 7.1CH recording in TDM mode. Due to more no.
of root clock frequency values some of the bit offsets got
shifted up by one. Also I2S1 on previous Samsung platforms
uses v3 dai type but on Exynos7 it is upgraded to v5 with
slightly modified register offsets for supporting more no.of
RFS values. Due to the above changes, the driver has to be
modified to handle all versions of I2S controller. For this
I introduced a new structure to hold modified bit offsets and
masks which is passed as dai data.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Internal DMA is available only on some of Samsung platforms.
So added a quirk for the same and made it optional.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DVC controls some digital volume features.
Volume Ramp is listed as "XX dB / YY steps",
and this enumerated settings are easy for users.
This patch adds rsnd_dvc_cfg_e and care about
enumerated settings.
Compiler will report like below at this point,
but, it will be removed if Volume Ramp was supported.
warning: '_rsnd_dvc_pcm_new_e' defined but not used
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DVC controls some digital volume features.
Some of them requests values for "each channels",
but, some of them requests values for "feature".
And, Volume Ramp has "feature" settings.
This patch adds rsnd_dvc_cfg_s and care about
single settings.
Compiler will report like below at this point,
but, it will be removed if Volume Ramp was supported.
warning: '_rsnd_dvc_pcm_new_s' defined but not used
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DVC controls some digital volume features.
Some of them requests values for "each channels",
but, some of them requests values for "feature".
Current dvc.c is supporting Mute/Volume,
and these have "each channels" settings.
This patch adds rsnd_dvc_cfg_m and care about
multiple settings for each channels.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to Enable/Disable DVC_DVUER register if we set
DVCp_ZCMCR, DVCp_VRCTR, DVCp_VRPDR, DVCp_VRDBR,
DVCp_VOL0R, DVCp_VOL1R, DVCp_VOL2R, DVCp_VOL3R,
DVCp_VOL4R, DVCp_VOL5R, DVCp_VOL6R, DVCp_VOL7R
and, these are controlled under rsnd_dvc_volume_update().
This patch moves DVC_DVUER settings to it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dvc_volume_update() is main function to control
DVC feature like Digital Volume / Mute / Ramp etc.
DVC_DVUCR should be controlled under this function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sst_save_shim64() is defined as static in code but header is non static.
Since this is not used other than file where defined remove non static
definition
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a switch to enable/disable boost stage of the output
amplifier. Applications that know that they do not need the output
amplifier boost stage can disable it to conserve a bit of power.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SSM4567 has support for a couple of different DAI formats. In TDM mode
it is also possible to select the TDM slot. This patch adds support for this
by implementing the set_fmt and set_tdm_slot callbacks.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a switch which can be used to enable/disable the DAC high-pass-filter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
In ACPI platform we need to save few registers of Shim on suspend and
restore them on resume, so add handlers to do this
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now the SST_IPC will support both ACPI and PCI, separate into core module
and PCI module. This also move probe function into PCI module and exports
the required symbols from core module
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
the 'platform' pointer in sst_map_modules_to_pipe() is deref in caller
function so we need to check for it in this function
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5645 codec support jack detection function. The patch will set
related registers if JD function is used.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
PLL should be powered up once filter power is on. So, "PLL1"
should be connected to filters instead of DACs.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch corrects the incorrect default register values.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch enables combo jack configuration according to dmi.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This enables the snd_soc_snow module to be auto-loaded.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Setting the DAC power-down bit for the ad193x will also disable the DAC
output amplifier. This will cause audible clicks and pops when starting or
stopping playback. To prevent this a new widget is introduced that controls
the DAC power-down bit. This widget is connected to both the DAC and a newly
introduced VMID widget. This makes sure that the DAC power-down bit is not
set as long as a audio sink is connected to the DAC output. At the same time
the PLL and SYSCLK will still be disabled when no playback or capture stream
is active.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Makes the code a bit cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Makes the code a bit cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Makes the code a bit cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Makes the code a bit cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In addtion expand the table to handle other values of sysclk. Instead
of making the table 3D, expand it to a more descriptive struct. The
divisors are specified in Table 19 of the 98090 data sheet version
0p94.
The dmic frequency was previously assumed. Instead make it explicit
and configurable through device tree. This now handles independently
set pclk and dmic frequency.
Based on downstream work by Ralph Birt.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Baytrail-based chromebooks have a 20MHz mclk, the code was setting
the divisor incorrectly in this case. According to the 98090
datasheet, the divisor should be set to DIV1 for 10 <= mclk <= 20.
Correct this and the surrounding clock ranges as well to match the
datasheet.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
DPCM can update the FE/BE connection states totally asynchronously
from the FE's PCM state. Most of FE/BE state changes are protected by
mutex, so that they won't race, but there are still some actions that
are uncovered. For example, suppose to switch a BE while a FE's
stream is running. This would call soc_dpcm_runtime_update(), which
sets FE's runtime_update flag, then sets up and starts BEs, and clears
FE's runtime_update flag again.
When a device emits XRUN during this operation, the PCM core triggers
snd_pcm_stop(XRUN). Since the trigger action is an atomic ops, this
isn't blocked by the mutex, thus it kicks off DPCM's trigger action.
It eventually updates and clears FE's runtime_update flag while
soc_dpcm_runtime_update() is running concurrently, and it results in
confusion.
Usually, for avoiding such a race, we take a lock. There is a PCM
stream lock for that purpose. However, as already mentioned, the
trigger action is atomic, and we can't take the lock for the whole
soc_dpcm_runtime_update() or other operations that include the lengthy
jobs like hw_params or prepare.
This patch provides an alternative solution. This adds a way to defer
the conflicting trigger callback to be executed at the end of FE/BE
state changes. For doing it, two things are introduced:
- Each runtime_update state change of FEs is protected via PCM stream
lock.
- The FE's trigger callback checks the runtime_update flag. If it's
not set, the trigger action is executed there. If set, mark the
pending trigger action and returns immediately.
- At the exit of runtime_update state change, it checks whether the
pending trigger is present. If yes, it executes the trigger action
at this point.
Reported-and-tested-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Fix the following build error when CONFIG_SLEEP is enabled and CONFIG_RUNTIME
is disabled. The BDW ADSP sleep PM functionality depends on the runtime pm
calls for context save/restore.
All error/warnings:
>> ERROR: "snd_soc_suspend" undefined!
>> ERROR: "snd_soc_resume" undefined!
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CPU and CODEC DAI probe are performed in exactly the same way. Which means
we can reuse the snd_soc_codec_dai_probe() for probing CPU DAIs as well.
While we are at it also drop the unused card parameter form the function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The card field of the snd_soc_dai field is very rarely used. We can use
dai->component->card instead and remove the card field from the snd_soc_dai
struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Properly use snd_soc_update_bits() instead of manually calling the CODEC
driver's read and write callbacks. The later will stop working once the
wm9713 driver has been converted to regmap.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The priv_data is allocated again here wrongly, and it
is not set to the driver data after assignment. This
make the pdata->dev is NULL and oops occurs on the first
call to hsw_volume_put.
The resource has been allocated in driver probe callback
hsw_pcm_dev_probe, so here just remove this sencond
allocation is OK.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patah separate bias level off to standby and off. The standby
level will provide the necessary power for JD and push button
functions.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For the broadwell official released FW(Since 8.4.1.43), the macro
SST_HSW_NO_CHANNELS is changed and fixed to 4, so here change it
to 4.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The CMR divider register is shared by playback and capture. The SSC driver
therefore tries to enforce rules so that the needed register content do
not conflict during simultaneous playback/capture. However, the
implementation also prevents changing the register content in
half-duplex scenarios, which is needed when using the OSS API.
Thus, only lock the divider if there is a stream in the other direction.
Fixes the below program to not fail with the atmel ssc dai in master mode.
int
main(void)
{
int fd;
int format;
int channels;
int speed;
if ((fd = open("/dev/dsp", O_WRONLY, 0)) == -1) {
perror("open");
return 1;
}
format = AFMT_S16_LE;
if (ioctl(fd, SNDCTL_DSP_SETFMT, &format) == -1) {
perror("SNDCTL_DSP_SETFMT");
return 1;
}
channels = 2;
if (ioctl(fd, SNDCTL_DSP_CHANNELS, &channels) == -1) {
perror("SNDCTL_DSP_CHANNELS");
return 1;
}
speed = 22025;
if (ioctl(fd, SNDCTL_DSP_SPEED, &speed) == -1) {
perror("SNDCTL_DSP_SPEED");
return 1;
}
return 0;
}
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since hardware may invert detect GPIO of headphone or mic, add one
property to support software invert.
Signed-off-by: Jianqun <jay.xu@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Typically a DAI does not need direct access to the platform. Currently the
only user of this field is in a platform driver where we have a more direct
way of getting a pointer to the platform. This patch updates the driver to
use the more direct way and then removes the platform field from the
snd_soc_dai struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Those are unused and new drivers should use device driver suspend/resume.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
For SND_SOC_ROCKCHIP_I2S, adding some text after the
tristate to make this directly user selectable.
Signed-off-by: Jianqun <jay.xu@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes build errors in configurations with I2C/SPI master disabled.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
on error in block prepare, we were returning the error code while still
holding the mutex. We are releasing the mutex in this patch before
return.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix build errors when CONFIG_I2C is not enabled by making the
driver depend on I2C.
../sound/soc/codecs/cs42l51-i2c.c:55:1: warning: data definition has no type or storage class [enabled by default]
module_i2c_driver(cs42l51_i2c_driver);
^
../sound/soc/codecs/cs42l51-i2c.c:55:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int]
../sound/soc/codecs/cs42l51-i2c.c:55:1: warning: parameter names (without types) in function declaration [enabled by default]
../sound/soc/codecs/cs42l51-i2c.c:45:26: warning: 'cs42l51_i2c_driver' defined but not used [-Wunused-variable]
static struct i2c_driver cs42l51_i2c_driver = {
^
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm9713 currently implements the virtual control for the Mic B Source MUX
using a virtual register. Replace this by using SOC_ENUM_SINGLE_VIRT().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Resources for the device should be allocated in the device driver probe
callback, rather than in the ASoC CODEC probe callback.
E.g. one advantage is that we can use device managed allocations.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Makes the code a bit cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use dev_err()/dev_warn() instead of printk(KERN_ERR/KERN_WARNING. This is
common practice and makes it easy to find out which device generated the
message. While we are at it also align the error messages with the other
AC'97 drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Makes the code a bit cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use dev_err() instead of printk(KERN_ERR. This is common practice and makes
it easy to find out which device generated the message. While we are at it
also align the error messages with the other AC'97 drivers.
Also avoid printing two error messages when the reset fails.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Makes the code a bit cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use dev_err() instead of printk(KERN_ERR. This is common practice and makes
it easy to find out which device generated the message. While we are at it
also align the error messages with the other AC'97 drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use dev_err() instead of printk(KERN_ERR. This is common practice and makes
it easy to find out which device generated the message. While we are at it
also align the error messages with the other AC'97 drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use dev_err()/dev_warn() instead of printk(KERN_ERR/KERN_WARNING. This is
common practice and makes it easy to find out which device generated the
message. While we are at it also align the error messages with the other
AC'97 drivers.
Also remove the info message that is printed when the driver is probed, this
is just noise in bootlog.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The constants defined in the ad1980 header are not used. So remove the file.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add jack dectection and event reporting for Broadwell. It use combo
jack on BDW platform, which including Mic Jack pin and Headphone
jack pin.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the PCI BAR and resource initialization to a separate routine
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver probe which initializes driver and remove which cleans up can be
shared with APCI as well, so move them to common init_context and
cleanup_context routines which can be used by ACPI as well
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This will be used by ACPI code as well, so moving to common routine helps
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This will be used by ACPI code as well, so moving to common routine helps
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This will be used by ACPI code as well, so moving to common routine helps
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some debug prints use dev context in sst_data. Store the device context for
the same.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch add low level IPC handling for compressed stream operations
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
.power callback is required to invoked for compressed audio as well to turn
on/off sst, so invoke them
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The firmware name was used worngly, so fix it up
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We would like the DSP firmware to be available in driver as soon as possible. So
use the async callback in driver to probe to load the firmware as soon as
usermode is up
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SST state change should be done under sst_lock
Signed-off-by: Mythri P K <mythri.p.k@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the runtime pm handlers, the driver already has code for
get/put for runtime pm and only these handlers being missing.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's already done in open/close.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that manual selection of drivers for audio subsystem components is
preferred AIC23 codec must be selectable in Kconfig to make it possible.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch will optimize the power consumption of rt286.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using clock gatings to save power, there are some known issues:
1. core clock gating (DCLCGE) must be disabled during D0 and D3 entry
and updating SRAM banks (VDRTCTL0).
2. DSP trunk clock gating (DTCGE) can cause FW crashes, disable it in D0.
To align with the new W/A flow from FW team, we must set VDRTCTL0.D3PGD
to 1 (D3 power gating disabled) at first startup and keep it all the time.
ADSP will be in D0 on first boot by BIOS part of WA. Required delays must
be preserved (waiting for HW to stabilize, after enabling CCG, changing
SRAM PG, D3PG).
D3->D0:
1. Disable core clock gating (VDRTCTL2.DCLCGE = 0)
2. Enable other CG apart from DTCG and DCLCG (VDRTCTL2. DCLCGE and DTCGE = 0)
3. Disable D3PG (VDRTCTL0.D3PGD = 1)
4. Power up necessary SRAM and wait at least for 18 clock cycles for every
bank you have powered up
5. Set D0 state(PMCS.PS = 0), wait for HW
6. Restore MCLK (clkctl.smos, disabled in D3 entry point 4)
7. Stall and reset core, set CSR
8. Enable core clock gating (VDRTCTL2.DCLCGE = 1), delay 50 us
9. Unreset core
10.Load FW, configure PLL and other necessary things
11.Unstall core
Changing SRAM PG during D0:
1. Disable core clock gating (VDRTCTL2.DCLCGE = 0)
2. Set PG mask
3. Wait at least for 18 clock cycles for every bank you have powered up
4. Enable core clock gating, delay 50 us
D0->D3:
1. Disable core clock gating (DCLCGE = 0)
2. Stall and reset core
3. Power down entire SRAM and wait at least for 18 clock cycles for every bank
(Enable SRAM PG (ISRAMPGE = 0x3FF, DSRAMPGE = 0xFFFFF, D3SRAMPGD = 0), remember
about preserving VDRTCTL0.D3PGD = 1)
4. Shutdown PLL, disable MCLK(clkctl.smos = 0), Enable DTCG to save power
5. Set D3 state(PMCS.PS = 3), delay 50 us
6. Enable core clock gating, delay 50 us
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following errors:
All error/warnings:
>> sound/soc/intel/sst-haswell-pcm.c:1168:13: error: 'hsw_pcm_prepare' undeclared here (not in a function)
.prepare = hsw_pcm_prepare,
^
>> sound/soc/intel/sst-haswell-pcm.c:1169:14: error: 'hsw_pcm_complete' undeclared here (not in a function)
.complete = hsw_pcm_complete,
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the debug output from IPCD and IPCX when booting fails.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During FW parsing and loading, block_list_prepare() may
be called for each raw data block copying and this may
made the hsw_block_enable() called mutiple times, which
increase block->users many times. The result of this is
hsw_block_disable() can't power gated the related block
when trying to free the blocks during suspend, and the
power gating status also confused.
Here check the block user status, only calling enable()
for those blocks who has no user yet. Remember that
this works correctlly on current case, where there are
enough SRAM memory so different module won't share a
memory block. For further usage, we may need restructure
the struct sst_mem_block to save the module list who is
using it.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 14621c7e5e ("ASoC: Consolidate CPU and CODEC DAI lookup")
consolidated the lookup of CPU DAIs and CODEC DAIs into a single function.
When matching a component by name for CODEC DAIs the code previous to the
patch compared the name in the DAI link table with component->name. For CPU
DAIs the code compared to dev_name(component->dev). The newly introduced
function ended up using the later as well.
For most components dev_name(component->dev) and component->name are the
same. The main notable exception are I2C devices where the driver name and
the device name are concatenated to form the component name. By using
dev_name(component->dev) instead of component->name the patch broke the
matching of I2C CODECs by name.
This patch restores the original behavior by using component->name instead
of dev_name(component->dev). This will be safe even for CPU DAIs since for
CPU DAIs both are the same.
Fixes: 14621c7e5e ("ASoC: Consolidate CPU and CODEC DAI lookup")
Reported-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add PM and RTD3 support to the HSW/BDW PCM driver. The PCM driver will
now save DSP context and then power off the DSP when it's not in use.
DSP power and context is then restored when it's next used.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add PM and RTD3 support to the HSW/BDW IPC driver. This patch
saves and restores the DSP context, loads and unloads FW and drops
any pending IPC messages after suspend.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lars-Peter Clausen
Jarkko Nikula
kbuild test robot
Qiao Zhou
Mengdong Lin
Zidan Wang
Padmavathi Venna
Takashi Iwai
Subhransu S. Prusty
Vinod Koul
Mark Brown
Oder Chiou
Charles Keepax
JS Park
Sudip Mukherjee
Masanari Iida
Markus Elfring
Fabio Estevam
Krishna Mohan Dani
Dmitry Eremin-Solenikov
Bard Liao
Dylan Reid
Richard Fitzgerald
Thomas Petazzoni
Misael Lopez Cruz
Peter Ujfalusi
Jean-Francois Moine
Kuninori Morimoto
Anil Kumar
Pavel Machek
Peter Rosin
Andreas Färber
Liam Girdwood
Jie Yang
Greg Kroah-Hartman
Jianqun
Max Filippov
Sudip Mukherjee
Randy Dunlap
Fang, Yang A
Mythri P K