Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds an SPI driver for the SPI controller found in various Marvell
Orion ARM SoCs. It currently supports only one slave, which must use SPI
mode 0.
[dbrownell@users.sourceforge.net: cleanups, meet specs, pass "sparse"]
Signed-off-by: Shadi Ammouri <shadi@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For some time my at91sam9260 board with JFFS2 on serial flash (m25p80)
would hang when accessing the serial flash and SPI bus. Slowing the SPI
clock down to 9 MHz reduced the occurrence of the hang from "always"
during boot to a nuisance level that allowed other SW development to
continue. Finally had to address this issue when an application stresses
the I/O to always cause a hang.
Hang seems to be caused by a missed SPI interrupt, so that the task ends
up waiting forever after calling spi_sync(). The fix has 2 parts. First
is to halt the DMA engine before the "current" PDC registers are loaded.
This ensures that the "next" registers are loaded before the DMA operation
takes off. The second part of the fix is a kludge that adds a
"completion" interrupt in case the ENDRX interrupt for the last segment of
the DMA chaining operation was missed.
The patch allows the SPI clock for the serial flash to be increased from 9
MHz to 15 MHz (or more?). No hangs or SPI overruns were encountered.
Haavard: while this patch does indeed improve things, I still see overruns
and CRC errors on my NGW100 board when running the DataFlash at 10 MHz.
However, I think some improvement is better than nothing, so I'm passing
this on for inclusion in 2.6.27.
Signed-off-by: Gerard Kam <gerardk5@verizon.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bug in the spi_s3c24xx driver where it does not reset the registers
of the hardware when resuming from suspend (this block has been reset over
suspend).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The original "Pass the bus number we expect the S3C24XX SPI driver to
attach to via the platform data." [1] patch was mis-sent, and missed two
important parts of the diff, which was to actually set the bus_num field
and add the relevant field to the platform data.
The previous commit 50f426b55d promised to
add a bus_num field, but failed to include the two hunks that added this
field to include/asm-arm/arch-s3c2410/spi.h and then pass it to the spi
core when creating the new master field in drivers/spi/spi_s3c24xx.c.
[1] git commit 50f426b55d
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The block transfer routine in the mpc52xx psc spi driver misinterpret
the datasheet. According to the processor datasheet the chipselect is
held as long as the EOF is not written.
Theoretically blocks of any sizes can be transferred in this way. The
old routine however writes an EOF after every word, which has the size
of size_of_word. This makes the transfer slow.
Also fixed some duplicate code.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
spi_new_device() allocates and registers an spi device all in one swoop.
If the driver needs to add extra data to the spi_device before it is
registered, then this causes problems. This is needed for OF device
tree support so that the SPI device tree helper can add a pointer to
the device node after the device is allocated, but before the device
is registered. OF aware SPI devices can then retrieve data out of the
device node to populate a platform data structure.
This patch splits the allocation and registration portions of code out
of spi_new_device() and creates two new functions; spi_alloc_device()
and spi_register_device(). spi_new_device() is modified to use the new
functions for allocation and registration. None of the existing users
of spi_new_device() should be affected by this change.
Drivers using the new API can forego the use of spi_board_info
structure to describe the device layout and populate data into the
spi_device structure directly.
This change is in preparation for adding an OF device tree parser to
generate spi_devices based on data in the device tree.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Improve PIO transfer mode of au1550 spi controller by continuing of spi
transfer, instead of aborting transfer when transmit underflow interrupt
occurrs.
Verified by oscilloscope that the spi clock pauses on trasmit underflow,
so transfer continuation is perfectly valid even though au1550 datasheet
says that on tx underflow zeroes will be transfered.
Also make some error messages more specific.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the Au1550 resource table and instead extract MMIO/IRQ/DMA
resources from platform resource information like any well-behaved
platform driver.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Another step to removing ->ioctl and to removing the BKL
[dbrownell@users.sourceforge.net: take final step; BKL not needed]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, 'modalias' in the spi_device structure is a 'const char *'.
The spi_new_device() function fills in the modalias value from a passed in
spi_board_info data block. Since it is a pointer copy, the new spi_device
remains dependent on the spi_board_info structure after the new spi_device
is registered (no other fields in spi_device directly depend on the
spi_board_info structure; all of the other data is copied).
This causes a problem when dynamically propulating the list of attached
SPI devices. For example, in arch/powerpc, the list of SPI devices can be
populated from data in the device tree. With the current code, the device
tree adapter must kmalloc() a new spi_board_info structure for each new
SPI device it finds in the device tree, and there is no simple mechanism
in place for keeping track of these allocations.
This patch changes modalias from a 'const char *' to a fixed char array.
By copying the modalias string instead of referencing it, the dependency
on the spi_board_info structure is eliminated and an outside caller does
not need to maintain a separate spi_board_info allocation for each device.
If searched through the code to the best of my ability for any references
to modalias which may be affected by this change and haven't found
anything. It has been tested with the lite5200b platform in arch/powerpc.
[dbrownell@users.sourceforge.net: cope with linux-next changes: KOBJ_NAME_LEN obliterated, etc]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use "if SPI_MASTER" to remove numerous dependencies.
[dbrownell@users.sourceforge.net: remove a couple now-needless EXPERIMENTAL dependencies too]
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
xilinx_spi->irq is unsigned, so the test fails
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrei Konovalov <akonovalov@ru.mvista.com>
Cc: Yuri Frolov <yfrolov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This updates the SPI clock rate calculations for the spi_mpc83xx driver.
Some boundary conditions were wrong, and in several cases divide-by-16
wasn't always needed
Signed-off-by: Chen Gong <g.chen@freescale.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This mirrors the functionality that driver_find_device has as well.
We add a start variable, and all callers of the function are fixed up at
the same time.
The block layer will be using this new functionality in a follow-on
patch.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Switch over to use the shiny new device_create_drvdata() call
instead of the original device_create() calls, so this continues
to work after device_create() is removed.
Note that this driver never had the race which motivated removing
the original call; it locked correctly.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
[ARM] 5171/1: ep93xx: fix compilation of modules using clocks
[ARM] 5133/2: at91sam9g20 defconfig file
[ARM] 5130/4: Support for the at91sam9g20
[ARM] 5160/1: IOP3XX: gpio/gpiolib support
[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
[ARM] 5084/1: zylonite: Register AC97 device
[ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
[ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
[ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
[ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
[ARM] 5144/1: pxaficp_ir: cleanup includes
[ARM] pxa: remove pxa_set_cken()
[ARM] pxa: allow clk aliases
[ARM] Feroceon: don't disable BPU on boot
[ARM] Orion: LED support for HP mv2120
[ARM] Orion: add RD88F5181L-FXO support
[ARM] Orion: add RD88F5181L-GE support
[ARM] Orion: add Netgear WNR854T support
[ARM] s3c2410_defconfig: update for current build
[ARM] Acer n30: Minor style and indentation fixes.
...
This got broken by the recent "fix rmmod $spi_driver while spidev-user is
active". I tested the rmmod & write path but didn't check the read path.
I am sorry. The read logic changed and spidev_sync_read() +
spidev_sync_write() do not return zero on success anymore but the number
of bytes that has been transfered over the bus. This patch changes the
logic and copy_to_user() gets called again.
The write path returns the number of bytes which are written to the
underlying device what may be less than the requested size. This patch
makes the same change to the read path or else we request a read of 20
bytes, get 10, don't call copy to user and report to the user that we read
10 bytes.
[akpm@linux-foundation.org: remove test of known-to-be-zero local]
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
imx_dma_request_by_prio can return channel number by itself.
No need to supply variable address through parameters.
Also converted all drivers using this function.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This addresses other oopsing paths in "spidev" by changing how it manages
refcounting. It decouples the lifecycle of the per-device data from the
class device (not just the spi device):
- Use class_{create,destroy} not class_{register,unregister}.
- Use device_{create,destroy} not device_{register,unregister}.
- Free the per-device data only when TWO conditions are true:
* Driver is unbound from underlying SPI device, and
* Device is no longer open (new)
Also, spi_{get,set}_drvdata not dev_{get,set}_drvdata for simpler code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Sebastian Siewior <bigeasy@tglx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Somehow the spidev code forgot to include a critical mechanism: when the
underlying device is removed (e.g. spi_master rmmod), open file
descriptors must be prevented from issuing new I/O requests to that
device. On penalty of the oopsing reported by Sebastian Siewior
<bigeasy@tglx.de> ...
This is a partial fix, adding handshaking between the lower level (SPI
messaging) and the file operations using the spi_dev. (It also fixes an
issue where reads and writes didn't return the number of bytes sent or
received.)
There's still a refcounting issue to be addressed (separately).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Reported-by: Sebastian Siewior <bigeasy@tglx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current driver may cause glitches on SPI CLK line since one must disable
the SPI controller before changing any HW settings. Fix this by implementing
a local spi_transfer function that won't change speed and/or word size while
CS is active.
While doing that heavy lifting a few other issues were addressed too:
- Make word size 16 and 32 work too.
- Honor bits_per_word and speed_hz in spi transaction.
- Optimize the common path.
This also stops using the "bitbang" framework (except for a few constants).
[Roel Kluin <12o3l@tiscali.nl>: "irq" needs to be signed]
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a typo in pxa2xx_spi.c, comment says "Enable the SSP clock", code
says: clk_disable ... so after resume, the SSP is dead.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ned Forrester <nforrester@whoi.edu>
Cc: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Fri, Apr 18, 2008 at 09:08:55PM +0200, Julia Lawall wrote:
> I found 63 occurrences of this problem with the following semantic match
> (http://www.emn.fr/x-info/coccinelle/):
>
> @@ unsigned int i; @@
>
> * i < 0
>
Since this one's always in the range 0-255, it could probably be made
signed, but it's just as easy to make it work unsigned.
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use PIO for full-duplex transfers, instead of DMA.
Signed-off-by: Vitja Makarov <vitja.makarov@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the baud rate divisor calculation code a bit more readable and add a
few comments.
Also fix wrong debug information being displayed when !new_1 and
max_speed_hz == 0.
[david-b@pacbell.net: fix it]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: "Janesh Ramakrishnan" <jramakrishnan@neuropace.com>
Acked-by David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Updates to the i.MX SPI controller driver:
1) Some comments changed and/or added.
2) End of transfers is now managed on TXFIFO empty interrupt after the
last write to TXFIFO. This speeds interrupt execution by removing
the wait for TXFIFO to become empty. On TXFIFO empty interrupt the
handler needs only to poll for the end of the ongoing transaction
(SPI_CONTROL_XCH) to close the transfer.
(2.1) Write only transfers are closed flushing RXFIFO.
(2.2) Read transfers are closed reading trailing bytes from RXFIFO.
(2.3) Read transfers where RXFIFO overrun occurred are closed by
flushing RXFIFO and aborting the message.
3) Fifos are now flushed via SPI disable after the end of ongoing
transaction.
Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A spi transfer with zero length is not invalid. For example, such
transfer (len == 0 && delay_usecs != 0) can be used to achieve delay
before first CLK edge after chipselect assertion.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various cleanups to pxa2xx_spi suggested by "sparse": make sure that
register addresess are "void __iomem *", and make a few functions properly
static.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ned Forrester <nforrester@whoi.edu>
Cc: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SPI core now expects num_chipselect to be set correctly as due to added
checks on the chip being selected before an transfer is allowed. This patch
adds a num_cs field to the platform data which needs to be set correctly
before adding the SPI platform device.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pass the bus number we expect the S3C24XX SPI driver to attach to via the
platform data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The s3c24xx_spi_txrx() function should initialise the completion each time
before using it, otherwise we end up with the possibility of returning success
before the interrupt handler has processed all the data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable SPI
platform drivers, to allow module auto loading.
[dbrownell@users.sourceforge.net: more drivers: registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bug in SPI probe: first initialize peripheral pins, and just after
register spi master device. This fixes problems with SPI drivers built-in
kernel.
Singed-off-by: Vitja Makarov <vitja.makarov@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix breakage cause by overzealous line wrapping; there should be only one
format string.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SPI controller drivers return number of bytes actually transfered from
bitbang->txrx_bufs() method. This updates handling of short transfers (where
the transfer size is less than requested):
- Even zero byte short transfers should report errors;
- Include short transfers in the total of transferred bytes;
- Use EREMOTEIO (like USB) not EMSGSIZE to report short transfers
Short transfers don't normally mean invalid message sizes, but if the
underlying controller driver needs to use EMSGSIZE it can still do so.
[db: fix two more minor issues]
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove struct pt_regs *regs from prototype of au1550_spi_irq handler to avoid
warning in request_irq(). Also fix comment type leadin.
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit id 94f389485e (Separate MPC52xx PSC FIOF
regsiters from the rest of PSC) split the PSC fifo registers away from the
core PSC regs. Doing so broke the mpc52xx_psc_spi driver.
This patch teaches the mpc52xx_psc_spi driver about the new PSC fifo
register definitions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: David Brownell <david-b@pacbell.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes a sequencing bug in spi driver pxa2xx_spi.c in which the chip select
for a transfer may be asserted before the clock polarity is set on the
interface. As a result of this bug, the clock signal may have the wrong
polarity at transfer start, so it may need to make an extra half transition
before the intended clock/data signals begin. (This probably means all
transfers are one bit out of sequence.)
This only occurs on the first transfer following a change in clock polarity
in systems using more than one more than one such polarity. The fix
assures that the clock mode is properly set before asserting chip select.
This bug was introduced in a patch merged on 2006/12/10, kernel 2.6.20.
The patch defines an additional bit in: include/asm-arm/arch-pxa/regs-ssp.h
for 2.6.25 and newer kernels but this addition must be made in:
include/asm-arm/arch-pxa/pxa-regs.h for kernels between 2.6.20 and 2.6.24,
inclusive
Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The atmel_spi driver does not initialize clock polarity correctly (except for
at91rm9200 CS0 channel) in some case.
The atmel_spi driver uses gpio-controlled chipselect. OTOH spi clock signal
is controlled by CSRn.CPOL bit, but this register controls clock signal
correctly only in 'real transfer' duration. At the time of cs_activate()
call, CSRn.CPOL will be initialized correctly, but the controller do not know
which channel is to be used next, so clock signal will stay at the inactive
state of last transfer. If clock polarity of new transfer and last transfer
was differ, new transfer will start with wrong clock signal state.
For example, if you started SPI MODE 2 or 3 transfer after SPI MODE 0 or 1
transfer, the clock signal state at the assertion of chipselect will be low.
Of course this will violates SPI transfer.
This patch is short term solution for this problem. It makes all CSRn.CPOL
match for the transfer before activating chipselect. For longer term, the
best fix might be to let NPCS0 stay selected permanently in MR and overwrite
CSR0 with to the new slave's settings before asserting CS.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some more references to dev->power.power_state. That field is overdue
for removal, but we can't do that while it's still referenced in the kernel.
The only reason to update it was to make the /sys/devices/.../power/state
files (now removed) work better.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use simpler comment headers, and strip out information that is maintained in
GIT history
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SPI writes should also not return until the last bit is sent.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Full duplex SPI operation should not read a dummy byte at the first transfer.
Bug and fix by Jean-Christian de Rivaz <jc@eclis.ch>:
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3678
Signed-off-by: Jean-Christian de Rivaz <jc@eclis.ch>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PBX 2 SPI devices need the nonstandard "cs change per word" mechanism.
This patch is one of three updating this driver to make the last data bits get
sent before advancing the transfer ... in this case, before the chipselect
gets deactivated.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the SPI driver's name when requesting gpio lines. When there are gpio
conflicts, this helps to narrow down the problems; "bfin-spi" is not
informative.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove useless return status check in restore_state function. Issue was
pointed out by Michael.
Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds driver OMAP SPI specific changes to support OMAP 3430
Signed-off-by: Girish S G <girishsg@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for SPI over SCI pins. SCI is a very simple serial controller
block that can be found on older SuperH processors. In theory it is
possible to use the SCI hardware block in syncronous mode, but this version
of the driver simply hooks up the bit banging code on the SCI pins.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The two S3C SPI master drivers got merged without much review, so I just
noticed that they're doing something that the SPI core code is responsible
for, rather than any adapter driver: they try to register SPI devices.
This removes that support from those drivers so they act normally.
Interestingly, none of the current boards are affected. So it's a net code
shrink with no loss of functionality.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In atmel_spi_next_xfer, xfer can be NULL because the next transfer may
already have been submitted to the PDC (using DMA chaining). This can
cause an oops, since the debug message assumed it was never null. The
fix changes how those debug messages are issued, ensuring that one is
issued each time a transfer is started instead of once per call.
Also, properly indent the "can this transfer be chained" test so it's
not hidden as if it were non-conditional code.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for chained transfers in the atmel_spi driver, letting the DMA
controller switch to the next buffer pair without CPU intervention. This
reduced I/O latencies by about 2% in one bulk I/O test. It should also help
work around several interrelated errata affecting chipselect 0 on at91rm9200
chips.
Almost all of the changes are in the reworked atmel_spi_next_xfer() function.
That's now called with the driver in one of three states:
1. It isn't transferring anything (in which case the first transfer
of the current message is going to be sent)
2. It has finished transfering a non-chainable transfer (in which
case it will go to the next transfer in the message)
3. It has finished transfering a chained transfer (in which case the
next transfer is already queued)
After that it will queue the next transfer if it can be chained.
Signed-off-by: Szilveszter Ordog <slipszi@gmail.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't insert (undesirable) delays between consecutive words (DLYBCT) or when
activating chipselects (DLYBS).
Removing the between-word delays improves the performance of bulk transfers
(such as mtd_dataflash, m25p80, mmc_spi) significantly. In one test, the
improvement was a factor of more than eight!
(The large DLYBCT value came from the legacy at91 SPI driver, and it's not
clear why it used such a huge value.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't update dev->power.power_state any more in the SPI core. The only
reason to update this scheduled-to-be-removed field was to make the
already-removed /sys/devices/.../power/state files work better.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case of QE we can use brg-frequency (which is qeclk/2).
Thus no need to divide sysclk in the spi_mpc83xx.
This patch also adds code to use get_brgfreq() on QE chips.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It is dangerous for an mpc52xx device driver to modify the port_config
register. If the driver is probed incorrectly, it will change the pin
IO configuration in ways which may not be compatible with the board.
port_config should be set up by the bootloader, or failing that, in
the platform setup code in arch/powerpc/platforms/52xx.
Also, modifying CDM registers directly can cause a race condition with
other drivers. Instead call a common routine to modify CDM settings.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Dragos Carp <dragos.carp@toptica.com>
Update MPC5200 drivers to also look for compatible properties in the
form "fsl,mpc5200-*" to better conform to open firmware generic names
recommended practice as published here:
http://www.openfirmware.org/1275/practice/gnames/gnamv14a.html
This patch should *not* break compatibility with older device trees
which do not use the 'fsl,' prefix. The drivers will still bind against
the older names also.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
1. make pxa2xx_spi.c use ssp_request() and ssp_free() to get the common
information of the designated SSP port.
2. remove those IRQ/memory request code, ssp_request() has done that for
the driver
3. the SPI platform device is thus made psuedo, no resource (memory/IRQ)
has to be defined, all will be retreived by ssp_request()
4. introduce ssp_get_clk_div() to handle controller difference in clock
divisor setting
5. use clk_xxx() API for clock enable/disable, and clk_get_rate() to
handle the different SSP clock frequency between different processors
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert to use the class iteration api.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Before transmission of the last word in PIO RX_ONLY mode rx+tx mode
is enabled:
/* prevent last RX_ONLY read from triggering
* more word i/o: switch to rx+tx
*/
if (c == 0 && tx == NULL)
mcspi_write_cs_reg(spi,
OMAP2_MCSPI_CHCONF0, l);
But because c is decremented after the test, c will never be zero and
rx+tx will not be enabled. This breaks RX_ONLY mode PIO transfers.
Fix it by decrementing c in the beginning of the various I/O loops.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mpc5200 platform code defines a bunch of map functions which duplicate the
functionality of of_iomap(). Remove them and use of_iomap() instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix a glitch reported by lockdep in the spi_bitbang code: it needs to
consistently block IRQs when holding that spinlock.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have a wifi module connected to the spi bus and got sometimes FIFO
overrun errors on the spi bus.
After some investigation i found that the driver loads the TCR (transmit
count) register before the RCR (receive count). When the transfer list is
not empty the atmel_spi_next_message is called while tx and rx are enabled.
As soon as the TCR is loaded, hardware starts transfer and causes a rx
fifo overrun because the RCR is not loaded yet.
Load the RCR before the TCR. After this patch the fifo overrun disapears
at out setup.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Rini van Zetten <rini@arvoo.nl>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Newton <will.newton@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- reconfigure SPI baud from speed_hz of each spi transfer
- according to spi_transfer.bits_per_word to reprogram register and setup
correct SPI operation handlers
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some sort of bloaty code, try to get these pin_req arrays built at compile-time
- move this static things to the blackfin board file
- add pin_req array to struct bfin5xx_spi_master
- tested on BF537/BF548 with SPI flash
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set correct baud for spi mmc and enable SPI only after DMA is started.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bug in u16_cs_chg_reader to read data_len-2 bytes data firstly, then read
out the last 2 bytes data
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move global SPI regs_base and dma_ch to struct driver_data. Test on BF54x SPI
Flash with 2 spi_master devices enabled.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move spin/waits to more correct locations in bfin SPI driver.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix SPI driver to work with SPI flash ST M25P16 on bf548
Currently the SPI driver enables the SPI controller and sets the SPI baud
register for each SPI transfer. But they should never be changed within a SPI
message session, in which several SPI transfers are pumped.
This patch moves SPI setting to the begining of a message session, and
never disables SPI controller until an error occurs.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use portmux mechanism to support SPI busses 1 and 2, instead of just the
original bus 0.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update spi driver to support multi-ports by using platform resources; tested
on STAMP537+SPI_MMC, other boards need more testing. Plus other minor
updates.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prevent people from setting bits in ctl_reg that the SPI framework already
handles, hopefully we can one day drop ctl_reg completely
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Russell King
Shadi Ammouri
Gerard Kam
Ben Dooks
Luotao Fu
Benjamin Herrenschmidt
FUJITA Tomonori
Grant Likely
Jan Nikitenko
Manuel Lauss
Alan Cox
Robert P. J. Day
Roel Kluin
Chen Gong
Greg Kroah-Hartman
David Brownell
Linus Torvalds
Jonathan Corbet
Stephen Rothwell
Sascha Hauer
Sebastian Siewior
Paulius Zaleckas
David Brownell
Joakim Tjernlund
Eric BENARD
Matthew Wilcox
Vitja Makarov
Haavard Skinnemoen
Andrea Paterniani
Atsushi Nemoto
Harvey Harrison
Alessandro Guido
Kay Sievers
Michael Hennerich
Mike Frysinger
Ned Forrester
Mike Frysinger
Sonic Zhang
Bryan Wu
Girish
Magnus Damm
Haavard Skinnemoen
Silvester Erdeg
Jeff Garzik
Ralf Baechle
Paulius Zaleckas
Paul Mackerras
Anton Vorontsov
eric miao
Dave Young
Kalle Valo
Rini van Zetten
Will Newton