Fix the following make W=1 kernel build warning:
drivers/thermal/thermal_core.c:1376: warning: expecting prototype for thermal_device_unregister(). Prototype was for thermal_zone_device_unregister() instead
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210517051020.3463536-1-yangyingliang@huawei.com
Export additional attributes:
ddr_data_rate (RO) : Show current DDR (Double Data Rate) data rate.
rfi_restriction (RW) : Show or set current state for RFI (Radio
Frequency Interference) protection.
These attributes use mailbox commands to get/set information. Here
command codes are:
0x0007: Read RFI restriction
0x0107: Read DDR data rate
0x0008: Write RFI restriction
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210517061441.1921901-3-srinivas.pandruvada@linux.intel.com
MODULE_DEVICE_TABLE is used to extract the device information out of the
driver and builds a table when being compiled. If using this macro,
kernel can find the driver if available when the device is plugged in,
and then loads that driver and initializes the device.
Fixes: 554fdbaf19 ("thermal: sprd: Add Spreadtrum thermal driver support")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210512093752.243168-1-zhang.lyra@gmail.com
The RK3568 SoCs have two Temperature Sensors, channel 0 is for CPU,
channel 1 is for GPU.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210506175514.168365-5-ezequiel@collabora.com
MSR_AMD64_SEV even though the spec clearly states so, and check CPUID
bits first.
- Send only one signal to a task when it is a SEGV_PKUERR si_code type.
- Do away with all the wankery of reserving X amount of memory in
the first megabyte to prevent BIOS corrupting it and simply and
unconditionally reserve the whole first megabyte.
- Make alternatives NOP optimization work at an arbitrary position
within the patched sequence because the compiler can put single-byte
NOPs for alignment anywhere in the sequence (32-bit retpoline), vs our
previous assumption that the NOPs are only appended.
- Force-disable ENQCMD[S] instructions support and remove update_pasid()
because of insufficient protection against FPU state modification in an
interrupt context, among other xstate horrors which are being addressed
at the moment. This one limits the fallout until proper enablement.
- Use cpu_feature_enabled() in the idxd driver so that it can be
build-time disabled through the defines in .../asm/disabled-features.h.
- Fix LVT thermal setup for SMI delivery mode by making sure the APIC
LVT value is read before APIC initialization so that softlockups during
boot do not happen at least on one machine.
- Mark all legacy interrupts as legacy vectors when the IO-APIC is
disabled and when all legacy interrupts are routed through the PIC.
-----BEGIN PGP SIGNATURE-----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=zRI1
-----END PGP SIGNATURE-----
Merge tag 'x86_urgent_for_v5.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
"A bunch of x86/urgent stuff accumulated for the last two weeks so
lemme unload it to you.
It should be all totally risk-free, of course. :-)
- Fix out-of-spec hardware (1st gen Hygon) which does not implement
MSR_AMD64_SEV even though the spec clearly states so, and check
CPUID bits first.
- Send only one signal to a task when it is a SEGV_PKUERR si_code
type.
- Do away with all the wankery of reserving X amount of memory in the
first megabyte to prevent BIOS corrupting it and simply and
unconditionally reserve the whole first megabyte.
- Make alternatives NOP optimization work at an arbitrary position
within the patched sequence because the compiler can put
single-byte NOPs for alignment anywhere in the sequence (32-bit
retpoline), vs our previous assumption that the NOPs are only
appended.
- Force-disable ENQCMD[S] instructions support and remove
update_pasid() because of insufficient protection against FPU state
modification in an interrupt context, among other xstate horrors
which are being addressed at the moment. This one limits the
fallout until proper enablement.
- Use cpu_feature_enabled() in the idxd driver so that it can be
build-time disabled through the defines in disabled-features.h.
- Fix LVT thermal setup for SMI delivery mode by making sure the APIC
LVT value is read before APIC initialization so that softlockups
during boot do not happen at least on one machine.
- Mark all legacy interrupts as legacy vectors when the IO-APIC is
disabled and when all legacy interrupts are routed through the PIC"
* tag 'x86_urgent_for_v5.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/sev: Check SME/SEV support in CPUID first
x86/fault: Don't send SIGSEGV twice on SEGV_PKUERR
x86/setup: Always reserve the first 1M of RAM
x86/alternative: Optimize single-byte NOPs at an arbitrary position
x86/cpufeatures: Force disable X86_FEATURE_ENQCMD and remove update_pasid()
dmaengine: idxd: Use cpu_feature_enabled()
x86/thermal: Fix LVT thermal setup for SMI delivery mode
x86/apic: Mark _all_ legacy interrupts when IO/APIC is missing
There are machines out there with added value crap^WBIOS which provide an
SMI handler for the local APIC thermal sensor interrupt. Out of reset,
the BSP on those machines has something like 0x200 in that APIC register
(timestamps left in because this whole issue is timing sensitive):
[ 0.033858] read lvtthmr: 0x330, val: 0x200
which means:
- bit 16 - the interrupt mask bit is clear and thus that interrupt is enabled
- bits [10:8] have 010b which means SMI delivery mode.
Now, later during boot, when the kernel programs the local APIC, it
soft-disables it temporarily through the spurious vector register:
setup_local_APIC:
...
/*
* If this comes from kexec/kcrash the APIC might be enabled in
* SPIV. Soft disable it before doing further initialization.
*/
value = apic_read(APIC_SPIV);
value &= ~APIC_SPIV_APIC_ENABLED;
apic_write(APIC_SPIV, value);
which means (from the SDM):
"10.4.7.2 Local APIC State After It Has Been Software Disabled
...
* The mask bits for all the LVT entries are set. Attempts to reset these
bits will be ignored."
And this happens too:
[ 0.124111] APIC: Switch to symmetric I/O mode setup
[ 0.124117] lvtthmr 0x200 before write 0xf to APIC 0xf0
[ 0.124118] lvtthmr 0x10200 after write 0xf to APIC 0xf0
This results in CPU 0 soft lockups depending on the placement in time
when the APIC soft-disable happens. Those soft lockups are not 100%
reproducible and the reason for that can only be speculated as no one
tells you what SMM does. Likely, it confuses the SMM code that the APIC
is disabled and the thermal interrupt doesn't doesn't fire at all,
leading to CPU 0 stuck in SMM forever...
Now, before
4f432e8bb1 ("x86/mce: Get rid of mcheck_intel_therm_init()")
due to how the APIC_LVTTHMR was read before APIC initialization in
mcheck_intel_therm_init(), it would read the value with the mask bit 16
clear and then intel_init_thermal() would replicate it onto the APs and
all would be peachy - the thermal interrupt would remain enabled.
But that commit moved that reading to a later moment in
intel_init_thermal(), resulting in reading APIC_LVTTHMR on the BSP too
late and with its interrupt mask bit set.
Thus, revert back to the old behavior of reading the thermal LVT
register before the APIC gets initialized.
Fixes: 4f432e8bb1 ("x86/mce: Get rid of mcheck_intel_therm_init()")
Reported-by: James Feeney <james@nurealm.net>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lkml.kernel.org/r/YKIqDdFNaXYd39wz@zn.tnic
Return -EINVAL when args is invalid instead of 'ret' which is set to
zero by a previous successful call to a function.
Fixes: ca66dca5ed ("thermal: qcom: add support for adc-tm5 PMIC thermal monitor")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210527092640.2070555-1-yangyingliang@huawei.com
Fix function name in ti-bandgap.c kernel-doc comment
to remove a warning.
drivers/thermal/ti-soc-thermal/ti-bandgap.c:787: warning: expecting
prototype for ti_bandgap_alert_init(). Prototype was for
ti_bandgap_talert_init() instead.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1621851963-36548-1-git-send-email-yang.lee@linux.alibaba.com
After commit 81ad4276b5 ("Thermal: Ignore invalid trip points") all
user_space governor notifications via RW trip point is broken in intel
thermal drivers. This commits marks trip_points with value of 0 during
call to thermal_zone_device_register() as invalid. RW trip points can be
0 as user space will set the correct trip temperature later.
During driver init, x86_package_temp and all int340x drivers sets RW trip
temperature as 0. This results in all these trips marked as invalid by
the thermal core.
To fix this initialize RW trips to THERMAL_TEMP_INVALID instead of 0.
Cc: <stable@vger.kernel.org>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210430122343.1789899-1-srinivas.pandruvada@linux.intel.com
- Fix spellos in comments for the tegra and sun8i (Bhaskar Chowdhury)
- Add the missing fifth node on the rcar_gen3 sensor (Niklas
Söderlund)
- Remove duplicate include in ti-bandgap (Zhang Yunkai)
- Assign error code in the error path in the function
thermal_of_populate_bind_params() (Jia-Ju Bai)
- Fix spelling mistake in a comment 'disabed' -> 'disabled' (Colin Ian
King)
- Use the device name instead of auto-numbering for a better
identification of the cooling device (Daniel Lezcano)
- Improve a bit the division accuracy in the power allocator governor
(Jeson Gao)
- Enable the missing third sensor on msm8976 (Konrad Dybcio)
- Add QCom tsens driver co-maintainer (Thara Gopinath)
- Fix memory leak and use after free errors in the core code (Daniel
Lezcano)
- Add the MDM9607 compatible bindings (Konrad Dybcio)
- Fix trivial spello in the copyright name for Hisilicon (Hao Fang)
- Fix negative index array access when converting the frequency to
power in the energy model (Brian-sy Yang)
- Add support for Gen2 new PMIC support for Qcom SPMI (David Collins)
- Update maintainer file for CPU cooling device section (Lukasz Luba)
- Fix missing put_device on error in the Qcom tsens driver (Guangqing
Zhu)
- Add compatible DT binding for sm8350 (Robert Foss)
- Add support for the MDM9607's tsens driver (Konrad Dybcio)
- Remove duplicate error messages in thermal_mmio and the bcm2835
driver (Ruiqi Gong)
- Add the Thermal Temperature Cooling driver (Zhang Rui)
- Remove duplicate error messages in the Hisilicon sensor driver (Ye
Bin)
- Use the devm_platform_ioremap_resource_byname() function instead of
a couple of corresponding calls (dingsenjie)
- Sort the headers alphabetically in the ti-bandgap driver (Zhen Lei)
- Add missing property in the DT thermal sensor binding (Rafał
Miłecki)
- Remove dead code in the ti-bandgap sensor driver (Lin Ruizhe)
- Convert the BRCM DT bindings to the yaml schema (Rafał Miłecki)
- Replace the thermal_notify_framework() call by a call to the
thermal_zone_device_update() function. Remove the function as well
as the corresponding documentation (Thara Gopinath)
- Add support for the ipq8064-tsens sensor along with a set of
cleanups and code preparation (Ansuel Smith)
- Add a lockless __thermal_cdev_update() function to improve the
locking scheme in the core code and governors (Lukasz Luba)
- Fix multiple cooling device notification changes (Lukasz Luba)
- Remove unneeded variable initialization (Colin Ian King)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAmCRqDIACgkQqDIjiipP
6E8O2Qf5AQvSVoN9WYRBLo1+a4mkGsJ/wHQMEsOA4FVHft5/QVkRtpMNbSiyq00O
YTpNuoBqiYm/tSTyzK/5Oh+0ucgm/ef4c4dTyPjZYw2GB+3rYNRAXdX/tB6Ggjl/
oUArUCoSQZjOU6Y573B05rcHp1PVM/XL9LgD1uX76tXA1MaGvsyC0cyPRAdOANke
W83BWI0XMhv8B1bZwHVB2Oft5x6HhqWBl3HKbNOmPEMtwkqqBCFAqB0wNEH88ZTf
2hyBjBoZQHdMkJsC0piMvIyAjHZiIjQB47VWz31EvKB3/E28xCqRqPViPq9QbrA5
got0+oDbxI96T024ndXRomc0SSxZnw==
=5THg
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Remove duplicate error message for the amlogic driver (Tang Bin)
- Fix spellos in comments for the tegra and sun8i (Bhaskar Chowdhury)
- Add the missing fifth node on the rcar_gen3 sensor (Niklas Söderlund)
- Remove duplicate include in ti-bandgap (Zhang Yunkai)
- Assign error code in the error path in the function
thermal_of_populate_bind_params() (Jia-Ju Bai)
- Fix spelling mistake in a comment 'disabed' -> 'disabled' (Colin Ian
King)
- Use the device name instead of auto-numbering for a better
identification of the cooling device (Daniel Lezcano)
- Improve a bit the division accuracy in the power allocator governor
(Jeson Gao)
- Enable the missing third sensor on msm8976 (Konrad Dybcio)
- Add QCom tsens driver co-maintainer (Thara Gopinath)
- Fix memory leak and use after free errors in the core code (Daniel
Lezcano)
- Add the MDM9607 compatible bindings (Konrad Dybcio)
- Fix trivial spello in the copyright name for Hisilicon (Hao Fang)
- Fix negative index array access when converting the frequency to
power in the energy model (Brian-sy Yang)
- Add support for Gen2 new PMIC support for Qcom SPMI (David Collins)
- Update maintainer file for CPU cooling device section (Lukasz Luba)
- Fix missing put_device on error in the Qcom tsens driver (Guangqing
Zhu)
- Add compatible DT binding for sm8350 (Robert Foss)
- Add support for the MDM9607's tsens driver (Konrad Dybcio)
- Remove duplicate error messages in thermal_mmio and the bcm2835
driver (Ruiqi Gong)
- Add the Thermal Temperature Cooling driver (Zhang Rui)
- Remove duplicate error messages in the Hisilicon sensor driver (Ye
Bin)
- Use the devm_platform_ioremap_resource_byname() function instead of a
couple of corresponding calls (dingsenjie)
- Sort the headers alphabetically in the ti-bandgap driver (Zhen Lei)
- Add missing property in the DT thermal sensor binding (Rafał Miłecki)
- Remove dead code in the ti-bandgap sensor driver (Lin Ruizhe)
- Convert the BRCM DT bindings to the yaml schema (Rafał Miłecki)
- Replace the thermal_notify_framework() call by a call to the
thermal_zone_device_update() function. Remove the function as well as
the corresponding documentation (Thara Gopinath)
- Add support for the ipq8064-tsens sensor along with a set of cleanups
and code preparation (Ansuel Smith)
- Add a lockless __thermal_cdev_update() function to improve the
locking scheme in the core code and governors (Lukasz Luba)
- Fix multiple cooling device notification changes (Lukasz Luba)
- Remove unneeded variable initialization (Colin Ian King)
* tag 'thermal-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (55 commits)
thermal/drivers/mtk_thermal: Remove redundant initializations of several variables
thermal/core/power allocator: Use the lockless __thermal_cdev_update() function
thermal/core/fair share: Use the lockless __thermal_cdev_update() function
thermal/core/fair share: Lock the thermal zone while looping over instances
thermal/core/power_allocator: Update once cooling devices when temp is low
thermal/core/power_allocator: Maintain the device statistics from going stale
thermal/core: Create a helper __thermal_cdev_update() without a lock
dt-bindings: thermal: tsens: Document ipq8064 bindings
thermal/drivers/tsens: Add support for ipq8064-tsens
thermal/drivers/tsens: Drop unused define for msm8960
thermal/drivers/tsens: Replace custom 8960 apis with generic apis
thermal/drivers/tsens: Fix bug in sensor enable for msm8960
thermal/drivers/tsens: Use init_common for msm8960
thermal/drivers/tsens: Add VER_0 tsens version
thermal/drivers/tsens: Convert msm8960 to reg_field
thermal/drivers/tsens: Don't hardcode sensor slope
Documentation: driver-api: thermal: Remove thermal_notify_framework from documentation
thermal/core: Remove thermal_notify_framework
iwlwifi: mvm: tt: Replace thermal_notify_framework
dt-bindings: thermal: brcm,ns-thermal: Convert to the json-schema
...
Several variables are being initialized with values that is never
read and being updated later with a new value. The initializations
are redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210422120412.246291-1-colin.king@canonical.com
Use the new helper function and avoid unnecessery second lock/unlock,
which was present in old approach with thermal_cdev_update().
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210422153624.6074-4-lukasz.luba@arm.com
Use the new helper function and avoid unnecessery second lock/unlock,
which was present in old approach with thermal_cdev_update().
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210422153624.6074-3-lukasz.luba@arm.com
The tz->lock must be hold during the looping over the instances in that
thermal zone. This lock was missing in the governor code since the
beginning, so it's hard to point into a particular commit.
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210422153624.6074-2-lukasz.luba@arm.com
The cooling device state change generates an event, also when there is no
need, because temperature is low and device is not throttled. Avoid to
unnecessary update the cooling device which means also not sending event.
The cooling device state has not changed because the temperature is still
below the first activation trip point value, so we can do this.
Add a tracking mechanism to make sure it updates cooling devices only
once - when the temperature dropps below first trip point.
Reported-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210422114308.29684-4-lukasz.luba@arm.com
When the temperature is below the first activation trip point the cooling
devices are not checked, so they cannot maintain fresh statistics. It
leads into the situation, when temperature crosses first trip point, the
statistics are stale and show state for very long period. This has impact
on IPA algorithm calculation and wrong decisions. Thus, check the cooling
devices even when the temperature is low, to refresh these statistics.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210422114308.29684-3-lukasz.luba@arm.com
There is a need to have a helper function which updates cooling device
state from the governors code. With this change governor can use
lock and unlock while calling helper function. This avoid unnecessary
second time lock/unlock which was in previous solution present in
governor implementation. This new helper function must be called
with mutex 'cdev->lock' hold.
The changed been discussed and part of code presented in thread:
https://lore.kernel.org/linux-pm/20210419084536.25000-1-lukasz.luba@arm.com/
Co-developed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20210422114308.29684-2-lukasz.luba@arm.com
Add support for tsens present in ipq806x SoCs based on generic msm8960
tsens driver.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210420183343.2272-9-ansuelsmth@gmail.com
Drop unused define for msm8960 replaced by generic api and reg_field.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210420183343.2272-8-ansuelsmth@gmail.com
Rework calibrate function to use common function. Derive the offset from
a missing hardcoded slope table and the data from the nvmem calib
efuses.
Drop custom get_temp function and use generic api.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210420183343.2272-7-ansuelsmth@gmail.com
Device based on tsens VER_0 contains a hardware bug that results in some
problem with sensor enablement. Sensor id 6-11 can't be enabled
selectively and all of them must be enabled in one step.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210420183343.2272-6-ansuelsmth@gmail.com
Use init_common and drop custom init for msm8960.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210420183343.2272-5-ansuelsmth@gmail.com
VER_0 is used to describe device based on tsens version before v0.1.
These device are devices based on msm8960 for example apq8064 or
ipq806x. Add support for VER_0 in tsens.c and set the right tsens feat
in tsens-8960.c file.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210420183343.2272-4-ansuelsmth@gmail.com
Convert msm9860 driver to reg_field to use the init_common
function.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210420183343.2272-3-ansuelsmth@gmail.com
Function compute_intercept_slope hardcode the sensor slope to
SLOPE_DEFAULT. Change this and use the default value only if a slope is
not defined. This is needed for tsens VER_0 that has a hardcoded slope
table.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210420183343.2272-2-ansuelsmth@gmail.com
thermal_notify_framework just updates for a single trip point where as
thermal_zone_device_update does other bookkeeping like updating the
temperature of the thermal zone and setting the next trip point. The only
driver that was using thermal_notify_framework was updated in the previous
patch to use thermal_zone_device_update instead. Since there are no users
for thermal_notify_framework remove it.
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210122023406.3500424-3-thara.gopinath@linaro.org
The function ti_bandgap_restore_ctxt() restores the context at resume
time. It checks if the sensor has a counter, reads the register but
does nothing with the value.
The block was probably omitted by the commit b87ea759a4.
Remove the unused variable as well as the block using it as we can
consider it as dead code.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: b87ea759a4 ("staging: omap-thermal: fix context restore function")
Signed-off-by: Lin Ruizhe <linruizhe@huawei.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210421084256.57591-1-linruizhe@huawei.com
For the sake of lisibility, reorder the header files alphabetically.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210406091912.2583-2-thunder.leizhen@huawei.com
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: dingsenjie <dingsenjie@yulong.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210414063943.96244-1-dingsenjie@163.com
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210409075224.2109503-1-yebin10@huawei.com
On Intel processors, the core frequency can be reduced below OS request,
when the current temperature reaches the TCC (Thermal Control Circuit)
activation temperature.
The default TCC activation temperature is specified by
MSR_IA32_TEMPERATURE_TARGET. However, it can be adjusted by specifying an
offset in degrees C, using the TCC Offset bits in the same MSR register.
This patch introduces a cooling devices driver that utilizes the TCC
Offset feature. The bigger the current cooling state is, the lower the
effective TCC activation temperature is, so that the processors can be
throttled earlier before system critical overheats.
Note that, on different platforms, the behavior might be different on
how fast the setting takes effect, and how much the CPU frequency is
reduced.
This patch has been tested on a KabyLake mobile platform from me, and also
on a CometLake platform from Doug.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210412125901.12549-1-rui.zhang@intel.com
There is a error message within devm_ioremap_resource already, so
remove the dev_err call to avoid redundant error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ruiqi Gong <gongruiqi1@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210408100329.7585-1-gongruiqi1@huawei.com
There is a error message within devm_ioremap_resource already, so
remove the dev_err call to avoid redundant error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ruiqi Gong <gongruiqi1@huawei.com>
Acked-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210408100144.7494-1-gongruiqi1@huawei.com
MDM9607 TSENS IP is very similar to the one of MSM8916, with
minor adjustments to various tuning values.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210319220802.198215-2-konrad.dybcio@somainline.org
Fixes coccicheck error:
drivers/thermal/qcom/tsens.c:759:4-10: ERROR: missing put_device; call
of_find_device_by_node on line 715, but without a corresponding object
release within this function.
Fixes: a7ff829761 ("drivers: thermal: tsens: Merge tsens-common.c into tsens.c")
Signed-off-by: Guangqing Zhu <zhuguangqing83@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210404125431.12208-1-zhuguangqing83@gmail.com
Add support for TEMP_ALARM GEN2 PMIC peripherals with digital
major revision 1. This revision utilizes a different temperature
threshold mapping than earlier revisions.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/69c90a004b3f5b7ae282f5ec5ca2920a48f23e02.1596040416.git.gurus@codeaurora.org
Slab OOB issue is scanned by KASAN in cpu_power_to_freq().
If power is limited below the power of OPP0 in EM table,
it will cause slab out-of-bound issue with negative array
index.
Return the lowest frequency if limited power cannot found
a suitable OPP in EM table to fix this issue.
Backtrace:
[<ffffffd02d2a37f0>] die+0x104/0x5ac
[<ffffffd02d2a5630>] bug_handler+0x64/0xd0
[<ffffffd02d288ce4>] brk_handler+0x160/0x258
[<ffffffd02d281e5c>] do_debug_exception+0x248/0x3f0
[<ffffffd02d284488>] el1_dbg+0x14/0xbc
[<ffffffd02d75d1d4>] __kasan_report+0x1dc/0x1e0
[<ffffffd02d75c2e0>] kasan_report+0x10/0x20
[<ffffffd02d75def8>] __asan_report_load8_noabort+0x18/0x28
[<ffffffd02e6fce5c>] cpufreq_power2state+0x180/0x43c
[<ffffffd02e6ead80>] power_actor_set_power+0x114/0x1d4
[<ffffffd02e6fac24>] allocate_power+0xaec/0xde0
[<ffffffd02e6f9f80>] power_allocator_throttle+0x3ec/0x5a4
[<ffffffd02e6ea888>] handle_thermal_trip+0x160/0x294
[<ffffffd02e6edd08>] thermal_zone_device_check+0xe4/0x154
[<ffffffd02d351cb4>] process_one_work+0x5e4/0xe28
[<ffffffd02d352f44>] worker_thread+0xa4c/0xfac
[<ffffffd02d360124>] kthread+0x33c/0x358
[<ffffffd02d289940>] ret_from_fork+0xc/0x18
Fixes: 371a3bc79c ("thermal/drivers/cpufreq_cooling: Fix wrong frequency converted from power")
Signed-off-by: brian-sy yang <brian-sy.yang@mediatek.com>
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Cc: stable@vger.kernel.org #v5.7
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201229050831.19493-1-michael.kao@mediatek.com
When the function successfully finishes it logs an information about
the registration of the cooling device and use its name to build the
message. Unfortunately it was freed right before:
drivers/thermal/cpuidle_cooling.c:218 __cpuidle_cooling_register()
warn: 'name' was already freed.
Fix this by freeing after the message happened.
Fixes: 6fd1b186d9 ("thermal/drivers/cpuidle_cooling: Use device name instead of auto-numbering")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20210319202522.891061-1-daniel.lezcano@linaro.org
The following error is reported by kbuild:
smatch warnings:
drivers/thermal/devfreq_cooling.c:433 of_devfreq_cooling_register_power() warn: passing zero to 'ERR_PTR'
Fix the error code by the setting the 'err' variable instead of 'cdev'.
Fixes: f8d354e821 ("thermal/drivers/devfreq_cooling: Use device name instead of auto-numbering")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210319202424.890968-1-daniel.lezcano@linaro.org
Fix the following error:
smatch warnings:
drivers/thermal/thermal_core.c:1020 __thermal_cooling_device_register() warn: possible memory leak of 'cdev'
by freeing the cdev when exiting the function in the error path.
Fixes: 5848376181 ("thermal/drivers/core: Use a char pointer for the cooling device name")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210319202257.890848-1-daniel.lezcano@linaro.org
The sensor *is* in fact used and does report temperature.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210225213119.116550-1-konrad.dybcio@somainline.org
There is a possible chance that some cooling device stats buffer
allocation fails due to very high cooling device max state value.
Later cooling device update sysfs can try to access stats data
for the same cooling device. It will lead to NULL pointer
dereference issue.
Add a NULL pointer check before accessing thermal cooling device
stats data. It fixes the following bug
[ 26.812833] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
[ 27.122960] Call trace:
[ 27.122963] do_raw_spin_lock+0x18/0xe8
[ 27.122966] _raw_spin_lock+0x24/0x30
[ 27.128157] thermal_cooling_device_stats_update+0x24/0x98
[ 27.128162] cur_state_store+0x88/0xb8
[ 27.128166] dev_attr_store+0x40/0x58
[ 27.128169] sysfs_kf_write+0x50/0x68
[ 27.133358] kernfs_fop_write+0x12c/0x1c8
[ 27.133362] __vfs_write+0x54/0x160
[ 27.152297] vfs_write+0xcc/0x188
[ 27.157132] ksys_write+0x78/0x108
[ 27.162050] ksys_write+0xf8/0x108
[ 27.166968] __arm_smccc_hvc+0x158/0x4b0
[ 27.166973] __arm_smccc_hvc+0x9c/0x4b0
[ 27.186005] el0_svc+0x8/0xc
Signed-off-by: Manaf Meethalavalappu Pallikunhi <manafm@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1607367181-24589-1-git-send-email-manafm@codeaurora.org
The division is used directly in re-divvying up power, the decimal part will
be discarded, devices will get less than the extra_actor_power - 1.
if using round the division to make the calculation more accurate.
For example:
actor0 received more than its max_power, it has the extra_power 759
actor1 received less than its max_power, it require extra_actor_power 395
actor2 received less than its max_power, it require extra_actor_power 365
actor1 and actor2 require the total capped_extra_power 760
using division in re-divvying up power
actor1 would actually get the extra_actor_power 394
actor2 would actually get the extra_actor_power 364
if using round the division in re-divvying up power
actor1 would actually get the extra_actor_power 394
actor2 would actually get the extra_actor_power 365
Signed-off-by: Jeson Gao <jeson.gao@unisoc.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1615796737-4688-1-git-send-email-gao.yunxiao6@gmail.com
There is a list with the purpose of grouping the cpufreq cooling
device together as described in the comments but actually it is
unused, the code evolved since 2012 and the list was no longer needed.
Delete the remaining unused list related code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20210314111333.16551-5-daniel.lezcano@linaro.org
Currently the naming of a cooling device is just a cooling technique
followed by a number. When there are multiple cooling devices using
the same technique, it is impossible to clearly identify the related
device as this one is just a number.
For instance:
thermal-idle-0
thermal-idle-1
thermal-idle-2
thermal-idle-3
etc ...
The 'thermal' prefix is redundant with the subsystem namespace. This
patch removes the 'thermal prefix and changes the number by the device
name. So the naming above becomes:
idle-cpu0
idle-cpu1
idle-cpu2
idle-cpu3
etc ...
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20210314111333.16551-4-daniel.lezcano@linaro.org
Currently the naming of a cooling device is just a cooling technique
followed by a number. When there are multiple cooling devices using
the same technique, it is impossible to clearly identify the related
device as this one is just a number.
For instance:
thermal-devfreq-0
thermal-devfreq-1
etc ...
The 'thermal' prefix is redundant with the subsystem namespace. This
patch removes the 'thermal' prefix and changes the number by the device
name. So the naming above becomes:
devfreq-5000000.gpu
devfreq-1d84000.ufshc
etc ...
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20210314111333.16551-3-daniel.lezcano@linaro.org
Currently the naming of a cooling device is just a cooling technique
followed by a number. When there are multiple cooling devices using
the same technique, it is impossible to clearly identify the related
device as this one is just a number.
For instance:
thermal-cpufreq-0
thermal-cpufreq-1
etc ...
The 'thermal' prefix is redundant with the subsystem namespace. This
patch removes the 'thermal' prefix and changes the number by the device
name. So the naming above becomes:
cpufreq-cpu0
cpufreq-cpu4
etc ...
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20210314111333.16551-2-daniel.lezcano@linaro.org
We want to have any kind of name for the cooling devices as we do no
longer want to rely on auto-numbering. Let's replace the cooling
device's fixed array by a char pointer to be allocated dynamically
when registering the cooling device, so we don't limit the length of
the name.
Rework the error path at the same time as we have to rollback the
allocations in case of error.
Tested with a dummy device having the name:
"Llanfairpwllgwyngyllgogerychwyrndrobwllllantysiliogogogoch"
A village on the island of Anglesey (Wales), known to have the longest
name in Europe.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20210314111333.16551-1-daniel.lezcano@linaro.org
When kcalloc() returns NULL to __tcbp or of_count_phandle_with_args()
returns zero or -ENOENT to count, no error return code of
thermal_of_populate_bind_params() is assigned.
To fix these bugs, ret is assigned with -ENOMEM and -ENOENT in these
cases, respectively.
Fixes: a92bab8919 ("of: thermal: Allow multiple devices to share cooling map")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210310122423.3266-1-baijiaju1990@gmail.com
Add support for up to five TSC nodes. The new THCODE values are taken
from the example in the datasheet.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210309162419.2621359-1-niklas.soderlund+renesas@ragnatech.se
The function devm_platform_ioremap_resource has already contains error
message, so remove the redundant dev_err here.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210222061105.6008-1-tangbin@cmss.chinamobile.com
thermal driver (Daniel Lezcano)
- Remove the notify ops as it is no longer used (Daniel Lezcano)
- Remove the 'forced passive' option and the unused bind/unbind
functions (Daniel Lezcano)
- Remove the THERMAL_TRIPS_NONE and the code cleanup around this
macro (Daniel Lezcano)
- Rework the delays to make them pre-computed instead of computing
them again and again at each polling interval (Daniel Lezcano)
- Remove the pointless 'thermal_zone_device_reset' function (Daniel
Lezcano)
- Use the critical and hot ops to prevent an unexpected system
shutdown on int340x (Kai-Heng Feng)
- Make the cooling device state private to the thermal subsystem
(Daniel Lezcano)
- Prevent to use not-power-aware actor devices with the power
allocator governor (Lukasz Luba)
- Remove 'zx' and 'tango' support along with the corresponding
platforms (Arnd Bergman)
- Fix several issues on the Omap thermal driver (Tony Lindgren)
- Add support for adc-tm5 PMIC thermal monitor for Qcom
platforms. Please note those changes rely on an immutable branch:
iio-thermal-5.11-rc1/ib-iio-thermal-5.11-rc1 from the iio tree
(Dmitry Baryshkov)
- Fix an initialization loop in the adc-tm5 (Colin Ian King)
- Fix a return error check in the cpufreq cooling device (Viresh Kumar)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAmAvkKMACgkQqDIjiipP
6E9yFggAmXy8t2j1mRvn/KLU+teTGIoSFkZ8mBnY2Sgip97IRZRhCwAZbUKOW0eI
bvpAzBjacxdZHT7OxxvGzCOq/zlAh4UoStI8bMpzdUWPdkAj4ippArLYGvagLym8
WEQysWnrr8V1RCZbQuBNjyLwjf0fcXkzIBU1mbZXA8T8Y6Yn646TdtsrVT4Idg1j
MOg7PAHBcTSY/wOReZKJ5TB1yvo2tNOuGOqUVbrIAHlRkiNTVHirVUq6aZGtTTKp
7ukcu8EI/o7XKBdQ5d9MZaHdwkcyAIJj4jdjmjkUJpa8VYQFPjayNyN3I+Py9lH2
jtWVYHQxZbY166IZP2yeXFjPzd6elw==
=Jmz4
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Use the newly introduced 'hot' and 'critical' ops for the acpi
thermal driver (Daniel Lezcano)
- Remove the notify ops as it is no longer used (Daniel Lezcano)
- Remove the 'forced passive' option and the unused bind/unbind
functions (Daniel Lezcano)
- Remove the THERMAL_TRIPS_NONE and the code cleanup around this macro
(Daniel Lezcano)
- Rework the delays to make them pre-computed instead of computing them
again and again at each polling interval (Daniel Lezcano)
- Remove the pointless 'thermal_zone_device_reset' function (Daniel
Lezcano)
- Use the critical and hot ops to prevent an unexpected system shutdown
on int340x (Kai-Heng Feng)
- Make the cooling device state private to the thermal subsystem
(Daniel Lezcano)
- Prevent to use not-power-aware actor devices with the power allocator
governor (Lukasz Luba)
- Remove 'zx' and 'tango' support along with the corresponding
platforms (Arnd Bergman)
- Fix several issues on the Omap thermal driver (Tony Lindgren)
- Add support for adc-tm5 PMIC thermal monitor for Qcom platforms
(Dmitry Baryshkov)
- Fix an initialization loop in the adc-tm5 (Colin Ian King)
- Fix a return error check in the cpufreq cooling device (Viresh Kumar)
* tag 'thermal-v5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (26 commits)
thermal: cpufreq_cooling: freq_qos_update_request() returns < 0 on error
thermal: qcom: Fix comparison with uninitialized variable channels_available
thermal: qcom: add support for adc-tm5 PMIC thermal monitor
dt-bindings: thermal: qcom: add adc-thermal monitor bindings
thermal: ti-soc-thermal: Use non-inverted define for omap4
thermal: ti-soc-thermal: Simplify polling with iopoll
thermal: ti-soc-thermal: Fix stuck sensor with continuous mode for 4430
thermal: ti-soc-thermal: Skip pointless register access for dra7
thermal/drivers/zx: Remove zx driver
thermal/drivers/tango: Remove tango driver
thermal: power allocator: fail binding for non-power actor devices
thermal/core: Make cooling device state change private
thermal: intel: pch: Fix unexpected shutdown at critical temperature
thermal: int340x: Fix unexpected shutdown at critical temperature
thermal/core: Remove pointless thermal_zone_device_reset() function
thermal/core: Remove ms based delay fields
thermal/core: Use precomputed jiffies for the polling
thermal/core: Precompute the delays from msecs to jiffies
thermal/core: Remove unused macro THERMAL_TRIPS_NONE
thermal/core: Remove THERMAL_TRIPS_NONE test
...
[ NOTE: unfortunately this tree had to be freshly rebased today,
it's a same-content tree of 82891be90f3c (-next published)
merged with v5.11.
The main reason for the rebase was an authorship misattribution
problem with a new commit, which we noticed in the last minute,
and which we didn't want to be merged upstream. The offending
commit was deep in the tree, and dependent commits had to be
rebased as well. ]
- Core scheduler updates:
- Add CONFIG_PREEMPT_DYNAMIC: this in its current form adds the
preempt=none/voluntary/full boot options (default: full),
to allow distros to build a PREEMPT kernel but fall back to
close to PREEMPT_VOLUNTARY (or PREEMPT_NONE) runtime scheduling
behavior via a boot time selection.
There's also the /debug/sched_debug switch to do this runtime.
This feature is implemented via runtime patching (a new variant of static calls).
The scope of the runtime patching can be best reviewed by looking
at the sched_dynamic_update() function in kernel/sched/core.c.
( Note that the dynamic none/voluntary mode isn't 100% identical,
for example preempt-RCU is available in all cases, plus the
preempt count is maintained in all models, which has runtime
overhead even with the code patching. )
The PREEMPT_VOLUNTARY/PREEMPT_NONE models, used by the vast majority
of distributions, are supposed to be unaffected.
- Fix ignored rescheduling after rcu_eqs_enter(). This is a bug that
was found via rcutorture triggering a hang. The bug is that
rcu_idle_enter() may wake up a NOCB kthread, but this happens after
the last generic need_resched() check. Some cpuidle drivers fix it
by chance but many others don't.
In true 2020 fashion the original bug fix has grown into a 5-patch
scheduler/RCU fix series plus another 16 RCU patches to address
the underlying issue of missed preemption events. These are the
initial fixes that should fix current incarnations of the bug.
- Clean up rbtree usage in the scheduler, by providing & using the following
consistent set of rbtree APIs:
partial-order; less() based:
- rb_add(): add a new entry to the rbtree
- rb_add_cached(): like rb_add(), but for a rb_root_cached
total-order; cmp() based:
- rb_find(): find an entry in an rbtree
- rb_find_add(): find an entry, and add if not found
- rb_find_first(): find the first (leftmost) matching entry
- rb_next_match(): continue from rb_find_first()
- rb_for_each(): iterate a sub-tree using the previous two
- Improve the SMP/NUMA load-balancer: scan for an idle sibling in a single pass.
This is a 4-commit series where each commit improves one aspect of the idle
sibling scan logic.
- Improve the cpufreq cooling driver by getting the effective CPU utilization
metrics from the scheduler
- Improve the fair scheduler's active load-balancing logic by reducing the number
of active LB attempts & lengthen the load-balancing interval. This improves
stress-ng mmapfork performance.
- Fix CFS's estimated utilization (util_est) calculation bug that can result in
too high utilization values
- Misc updates & fixes:
- Fix the HRTICK reprogramming & optimization feature
- Fix SCHED_SOFTIRQ raising race & warning in the CPU offlining code
- Reduce dl_add_task_root_domain() overhead
- Fix uprobes refcount bug
- Process pending softirqs in flush_smp_call_function_from_idle()
- Clean up task priority related defines, remove *USER_*PRIO and
USER_PRIO()
- Simplify the sched_init_numa() deduplication sort
- Documentation updates
- Fix EAS bug in update_misfit_status(), which degraded the quality
of energy-balancing
- Smaller cleanups
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=pyaG
-----END PGP SIGNATURE-----
Merge tag 'sched-core-2021-02-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
"Core scheduler updates:
- Add CONFIG_PREEMPT_DYNAMIC: this in its current form adds the
preempt=none/voluntary/full boot options (default: full), to allow
distros to build a PREEMPT kernel but fall back to close to
PREEMPT_VOLUNTARY (or PREEMPT_NONE) runtime scheduling behavior via
a boot time selection.
There's also the /debug/sched_debug switch to do this runtime.
This feature is implemented via runtime patching (a new variant of
static calls).
The scope of the runtime patching can be best reviewed by looking
at the sched_dynamic_update() function in kernel/sched/core.c.
( Note that the dynamic none/voluntary mode isn't 100% identical,
for example preempt-RCU is available in all cases, plus the
preempt count is maintained in all models, which has runtime
overhead even with the code patching. )
The PREEMPT_VOLUNTARY/PREEMPT_NONE models, used by the vast
majority of distributions, are supposed to be unaffected.
- Fix ignored rescheduling after rcu_eqs_enter(). This is a bug that
was found via rcutorture triggering a hang. The bug is that
rcu_idle_enter() may wake up a NOCB kthread, but this happens after
the last generic need_resched() check. Some cpuidle drivers fix it
by chance but many others don't.
In true 2020 fashion the original bug fix has grown into a 5-patch
scheduler/RCU fix series plus another 16 RCU patches to address the
underlying issue of missed preemption events. These are the initial
fixes that should fix current incarnations of the bug.
- Clean up rbtree usage in the scheduler, by providing & using the
following consistent set of rbtree APIs:
partial-order; less() based:
- rb_add(): add a new entry to the rbtree
- rb_add_cached(): like rb_add(), but for a rb_root_cached
total-order; cmp() based:
- rb_find(): find an entry in an rbtree
- rb_find_add(): find an entry, and add if not found
- rb_find_first(): find the first (leftmost) matching entry
- rb_next_match(): continue from rb_find_first()
- rb_for_each(): iterate a sub-tree using the previous two
- Improve the SMP/NUMA load-balancer: scan for an idle sibling in a
single pass. This is a 4-commit series where each commit improves
one aspect of the idle sibling scan logic.
- Improve the cpufreq cooling driver by getting the effective CPU
utilization metrics from the scheduler
- Improve the fair scheduler's active load-balancing logic by
reducing the number of active LB attempts & lengthen the
load-balancing interval. This improves stress-ng mmapfork
performance.
- Fix CFS's estimated utilization (util_est) calculation bug that can
result in too high utilization values
Misc updates & fixes:
- Fix the HRTICK reprogramming & optimization feature
- Fix SCHED_SOFTIRQ raising race & warning in the CPU offlining code
- Reduce dl_add_task_root_domain() overhead
- Fix uprobes refcount bug
- Process pending softirqs in flush_smp_call_function_from_idle()
- Clean up task priority related defines, remove *USER_*PRIO and
USER_PRIO()
- Simplify the sched_init_numa() deduplication sort
- Documentation updates
- Fix EAS bug in update_misfit_status(), which degraded the quality
of energy-balancing
- Smaller cleanups"
* tag 'sched-core-2021-02-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
sched,x86: Allow !PREEMPT_DYNAMIC
entry/kvm: Explicitly flush pending rcuog wakeup before last rescheduling point
entry: Explicitly flush pending rcuog wakeup before last rescheduling point
rcu/nocb: Trigger self-IPI on late deferred wake up before user resume
rcu/nocb: Perform deferred wake up before last idle's need_resched() check
rcu: Pull deferred rcuog wake up to rcu_eqs_enter() callers
sched/features: Distinguish between NORMAL and DEADLINE hrtick
sched/features: Fix hrtick reprogramming
sched/deadline: Reduce rq lock contention in dl_add_task_root_domain()
uprobes: (Re)add missing get_uprobe() in __find_uprobe()
smp: Process pending softirqs in flush_smp_call_function_from_idle()
sched: Harden PREEMPT_DYNAMIC
static_call: Allow module use without exposing static_call_key
sched: Add /debug/sched_preempt
preempt/dynamic: Support dynamic preempt with preempt= boot option
preempt/dynamic: Provide irqentry_exit_cond_resched() static call
preempt/dynamic: Provide preempt_schedule[_notrace]() static calls
preempt/dynamic: Provide cond_resched() and might_resched() static calls
preempt: Introduce CONFIG_PREEMPT_DYNAMIC
static_call: Provide DEFINE_STATIC_CALL_RET0()
...
freq_qos_update_request() returns 1 if the effective constraint value
has changed, 0 if the effective constraint value has not changed, or a
negative error code on failures.
The frequency constraints for CPUs can be set by different parts of the
kernel. If the maximum frequency constraint set by other parts of the
kernel are set at a lower value than the one corresponding to cooling
state 0, then we will never be able to cool down the system as
freq_qos_update_request() will keep on returning 0 and we will skip
updating cpufreq_state and thermal pressure.
Fix that by doing the updates even in the case where
freq_qos_update_request() returns 0, as we have effectively set the
constraint to a new value even if the consolidated value of the
actual constraint is unchanged because of external factors.
Cc: v5.7+ <stable@vger.kernel.org> # v5.7+
Reported-by: Thara Gopinath <thara.gopinath@linaro.org>
Fixes: f12e4f66ab ("thermal/cpu-cooling: Update thermal pressure in case of a maximum frequency capping")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Thara Gopinath<thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/b2b7e84944937390256669df5a48ce5abba0c1ef.1613540713.git.viresh.kumar@linaro.org
Currently the check of chip->channels[i].channel is against an the
uninitialized variable channels_available. I believe the variable
channels_available needs to be fetched first by the call to adc_tm5_read
before the channels check. Fix the issue swapping the order of the
channels check loop with the call to adc_tm5_read.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: ca66dca5ed ("thermal: qcom: add support for adc-tm5 PMIC thermal monitor")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210216151626.162996-1-colin.king@canonical.com
Add support for Thermal Monitoring part of PMIC5. This part is closely
coupled with ADC, using it's channels directly. ADC-TM support
generating interrupts on ADC value crossing low or high voltage bounds,
which is used to support thermal trip points.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205000118.493610-3-dmitry.baryshkov@linaro.org
When we set bit 10 high we use continuous mode and not single
mode. Let's correct this to avoid confusion. No functional
changes here, the code does the right thing with bit 10.
Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205134534.49200-5-tony@atomide.com
We can use iopoll for checking the EOCZ (end of conversion) bit. And with
this we now also want to handle the timeout errors properly.
For omap3, we need about 1.2ms for the single mode sampling to wait for
EOCZ down, so let's use 1.5ms timeout there. Waiting for sampling to start
is faster and we can use 1ms timeout.
Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205134534.49200-4-tony@atomide.com
At least for 4430, trying to use the single conversion mode eventually
hangs the thermal sensor. This can be quite easily seen with errors:
thermal thermal_zone0: failed to read out thermal zone (-5)
Also, trying to read the temperature shows a stuck value with:
$ while true; do cat /sys/class/thermal/thermal_zone0/temp; done
Where the temperature is not rising at all with the busy loop.
Additionally, the EOCZ (end of conversion) bit is not rising on 4430 in
single conversion mode while it works fine in continuous conversion mode.
It is also possible that the hung temperature sensor can affect the
thermal shutdown alert too.
Let's fix the issue by adding TI_BANDGAP_FEATURE_CONT_MODE_ONLY flag and
use it for 4430.
Note that we also need to add udelay to for the EOCZ (end of conversion)
bit polling as otherwise we have it time out too early on 4430. We'll be
changing the loop to use iopoll in the following clean-up patch.
Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205134534.49200-3-tony@atomide.com
On dra7, there is no Start of Conversion (SOC) register bit and we have an
empty bgap_soc_mask in the configuration for the thermal driver. Let's not
do pointless reads and writes with the empty mask.
There's also no point waiting for End of Conversion bit (EOCZ) to go high
on dra7. We only care about it going down, and are now mostly timing out
waiting for EOCZ high while it has already gone down.
When we add checking for the timeout errors in a later patch, waiting for
EOCZ high would cause bogus time out errors.
Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205134534.49200-2-tony@atomide.com
This functionality has nothing to do with MCE, move it to the thermal
framework and untangle it from MCE.
Requested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lkml.kernel.org/r/20210202121003.GD18075@zn.tnic
The zte zx platform is getting removed, so this driver is no
longer needed.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210120162400.4115366-3-arnd@kernel.org
The tango platform is getting removed, so the driver is no
longer needed.
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210120162400.4115366-2-arnd@kernel.org
The thermal zone can have cooling devices which are missing power actor
API. This could be due to missing Energy Model for devfreq or cpufreq
cooling device. In this case it is safe to fail the binding rather than
trying to workaround and control the temperature in such thermal zone.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210119114126.19480-1-lukasz.luba@arm.com
The change of the cooling device state should be used by the governor
or at least by the core code, not by the drivers themselves.
Remove the API usage and move the function declaration to the internal
headers.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20210118173824.9970-1-daniel.lezcano@linaro.org
Like previous patch, the intel_pch_thermal device is not in ACPI
ThermalZone namespace, so a critical trip doesn't mean shutdown.
Override the default .critical callback to prevent surprising thermal
shutdoown.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201221172345.36976-2-kai.heng.feng@canonical.com
We are seeing thermal shutdown on Intel based mobile workstations, the
shutdown happens during the first trip handle in
thermal_zone_device_register():
kernel: thermal thermal_zone15: critical temperature reached (101 C), shutting down
However, we shouldn't do a thermal shutdown here, since
1) We may want to use a dedicated daemon, Intel's thermald in this case,
to handle thermal shutdown.
2) For ACPI based system, _CRT doesn't mean shutdown unless it's inside
ThermalZone namespace. ACPI Spec, 11.4.4 _CRT (Critical Temperature):
"... If this object it present under a device, the device’s driver
evaluates this object to determine the device’s critical cooling
temperature trip point. This value may then be used by the device’s
driver to program an internal device temperature sensor trip point."
So a "critical trip" here merely means we should take a more aggressive
cooling method.
As int340x device isn't present under ACPI ThermalZone, override the
default .critical callback to prevent surprising thermal shutdown.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201221172345.36976-1-kai.heng.feng@canonical.com
The function thermal_zone_device_reset() is called in the
thermal_zone_device_register() which allocates and initialize the
structure. The passive field is already zero-ed by the allocation, the
function is useless.
Call directly thermal_zone_device_init() instead and
thermal_zone_device_reset().
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201222181110.1231977-1-daniel.lezcano@linaro.org
The code does no longer use the ms unit based fields to set the
delays as they are replaced by the jiffies.
Remove them and replace their user to use the jiffies version instead.
Cc: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Peter Kästle <peter@piie.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201216220337.839878-3-daniel.lezcano@linaro.org
The delays are also stored in jiffies based unit. Use them instead of
the ms.
Cc: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201216220337.839878-2-daniel.lezcano@linaro.org
The delays are stored in ms units and when the polling function is
called this delay is converted into jiffies at each call.
Instead of doing the conversion again and again, compute the jiffies
at init time and use the value directly when setting the polling.
Cc: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201216220337.839878-1-daniel.lezcano@linaro.org
The last site calling the thermal_zone_bind_cooling_device() function
with the THERMAL_TRIPS_NONE parameter was removed.
We can get rid of this test as no user of this function is calling
this function with this parameter.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201214233811.485669-5-daniel.lezcano@linaro.org
The functions thermal_zone_device_rebind_exception and
thermal_zone_device_unbind_exception are not used from anywhere.
Remove that code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201214233811.485669-2-daniel.lezcano@linaro.org
The code was reorganized in 2012 with the commit 0c01ebbfd3.
The main change is a loop on the trip points array and a unconditional
call to the throttle() ops of the governors for each of them even if
the trip temperature is not reached yet.
With this change, the 'forced_passive' is no longer checked in the
thermal_zone_device_update() function but in the step wise governor's
throttle() callback.
As the force_passive does no belong to the trip point array, the
thermal_zone_device_update() can not compare with the specified
passive temperature, thus does not detect the passive limit has been
crossed. Consequently, throttle() is never called and the
'forced_passive' branch is unreached.
In addition, the default processor cooling device is not automatically
bound to the thermal zone if there is not passive trip point, thus the
'forced_passive' can not operate.
If there is an active trip point, then the throttle function will be
called to mitigate at this temperature and the 'forced_passive' will
override the mitigation of the active trip point in this case but with
the default cooling device bound to the thermal zone, so usually a
fan, and that is not a passive cooling effect.
Given the regression exists since more than 8 years, nobody complained
and at the best of my knowledge there is no bug open in
https://bugzilla.kernel.org, it is reasonable to say it is unused.
Remove the 'forced_passive' related code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201214233811.485669-1-daniel.lezcano@linaro.org
Several parts of the kernel are already using the effective CPU
utilization (as seen by the scheduler) to get the current load on the
CPU, do the same here instead of depending on the idle time of the CPU,
which isn't that accurate comparatively.
This is also the right thing to do as it makes the cpufreq governor
(schedutil) align better with the cpufreq_cooling driver, as the power
requested by cpufreq_cooling governor will exactly match the next
frequency requested by the schedutil governor since they are both using
the same metric to calculate load.
This was tested on ARM Hikey6220 platform with hackbench, sysbench and
schbench. None of them showed any regression or significant
improvements. Schbench is the most important ones out of these as it
creates the scenario where the utilization numbers provide a better
estimate of the future.
Scenario 1: The CPUs were mostly idle in the previous polling window of
the IPA governor as the tasks were sleeping and here are the details
from traces (load is in %):
Old: thermal_power_cpu_get_power: cpus=00000000,000000ff freq=1200000 total_load=203 load={{0x35,0x1,0x0,0x31,0x0,0x0,0x64,0x0}} dynamic_power=1339
New: thermal_power_cpu_get_power: cpus=00000000,000000ff freq=1200000 total_load=600 load={{0x60,0x46,0x45,0x45,0x48,0x3b,0x61,0x44}} dynamic_power=3960
Here, the "Old" line gives the load and requested_power (dynamic_power
here) numbers calculated using the idle time based implementation, while
"New" is based on the CPU utilization from scheduler.
As can be clearly seen, the load and requested_power numbers are simply
incorrect in the idle time based approach and the numbers collected from
CPU's utilization are much closer to the reality.
Scenario 2: The CPUs were busy in the previous polling window of the IPA
governor:
Old: thermal_power_cpu_get_power: cpus=00000000,000000ff freq=1200000 total_load=800 load={{0x64,0x64,0x64,0x64,0x64,0x64,0x64,0x64}} dynamic_power=5280
New: thermal_power_cpu_get_power: cpus=00000000,000000ff freq=1200000 total_load=708 load={{0x4d,0x5c,0x5c,0x5b,0x5c,0x5c,0x51,0x5b}} dynamic_power=4672
As can be seen, the idle time based load is 100% for all the CPUs as it
took only the last window into account, but in reality the CPUs aren't
that loaded as shown by the utilization numbers.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lkml.kernel.org/r/9c255c83d78d58451abc06848001faef94c87a12.1607400596.git.viresh.kumar@linaro.org
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl/cYxEACgkQqDIjiipP
6E//swf+NQe5V9ioQ7j4wshFJLwIfu7uV0pNeTx3aHGx2R03hYwtcIS21/77SAgB
3KQikcrblrT49oKyCfkzYRUmdTgweSFHj9wN9OWBsIStus2sTFho9EOmcpyX0KOJ
2QBiOvvD3+xlhSMiKelJ/3OohrHwYE9ZMMW9pL5bZKDXuHXBao2Y1s7ZB9EaaM11
p+Qo9m9E+Pbp4WdJX+AgTHYMyKpVZbbAY+hulSOWDIcOms05MtPF5glPhQQS9yfR
yS+xZVtS2G9LCkuMdbXBGEn7vKJeqjH2aJ21+UkpBQUFLQExXvitx2O3w7i0cbup
Q6j4CHTtDcXBKl9p1L5wjmjEM6hwMA==
=5VgU
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.11-2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal fixlet from Daniel Lezcano:
"A trivial change which fell through the cracks:
Add Alder Lake support ACPI ids (Srinivas Pandruvada)"
* tag 'thermal-v5.11-2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
thermal: int340x: Support Alder Lake
Pull thermal updates from Daniel Lezcano:
- Add upper and lower limits clamps for the cooling device state in the
power allocator governor (Michael Kao)
- Add upper and lower limits support for the power allocator governor
(Lukasz Luba)
- Optimize conditions testing for the trip points (Bernard Zhao)
- Replace spin_lock_irqsave by spin_lock in hard IRQ on the rcar driver
(Tian Tao)
- Add MT8516 dt-bindings and device reset optional support (Fabien
Parent)
- Add a quiescent period to cool down the PCH when entering S0iX
(Sumeet Pawnikar)
- Use bitmap API instead of re-inventing the wheel on sun8i (Yangtao
Li)
- Remove useless NULL check in the hwmon driver (Bernard Zhao)
- Update the current state in the cpufreq cooling device only if the
frequency change is effective (Zhuguangqing)
- Improve the schema validation for the rcar DT bindings (Geert
Uytterhoeven)
- Fix the user time unit in the documentation (Viresh Kumar)
- Add PCI ids for Lewisburg PCH (Andres Freund)
- Add hwmon support on amlogic (Martin Blumenstingl)
- Fix build failure for PCH entering on in S0iX (Randy Dunlap)
- Improve the k_* coefficient for the power allocator governor (Lukasz
Luba)
- Fix missing const on a sysfs attribute (Rikard Falkeborn)
- Remove broken interrupt support on rcar to be replaced by a new one
(Niklas Söderlund)
- Improve the error code handling at init time on imx8mm (Fabio
Estevam)
- Compute interval validity once instead at each temperature reading
iteration on acerhdf (Daniel Lezcano)
- Add r8a779a0 support (Niklas Söderlund)
- Add PCI ids for AlderLake PCH and mmio refactoring (Srinivas
Pandruvada)
- Add RFIM and mailbox support on int340x (Srinivas Pandruvada)
- Use macro for temperature calculation on PCH (Sumeet Pawnikar)
- Simplify return conditions at probe time on Broadcom (Zheng Yongjun)
- Fix workload name on PCH (Srinivas Pandruvada)
- Migrate the devfreq cooling device code to the energy model API
(Lukasz Luba)
- Emit a warning if the thermal_zone_device_update is called without
the .get_temp() ops (Daniel Lezcano)
- Add critical and hot ops for the thermal zone (Daniel Lezcano)
- Remove notification usage when critical is reached on rcar (Daniel
Lezcano)
- Fix devfreq build when ENERGY_MODEL is not set (Lukasz Luba)
* tag 'thermal-v5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (45 commits)
thermal/drivers/devfreq_cooling: Fix the build when !ENERGY_MODEL
thermal/drivers/rcar: Remove notification usage
thermal/core: Add critical and hot ops
thermal/core: Emit a warning if the thermal zone is updated without ops
drm/panfrost: Register devfreq cooling and attempt to add Energy Model
thermal: devfreq_cooling: remove old power model and use EM
thermal: devfreq_cooling: add new registration functions with Energy Model
thermal: devfreq_cooling: use a copy of device status
thermal: devfreq_cooling: change tracing function and arguments
thermal: int340x: processor_thermal: Correct workload type name
thermal: broadcom: simplify the return expression of bcm2711_thermal_probe()
thermal: intel: pch: use macro for temperature calculation
thermal: int340x: processor_thermal: Add mailbox driver
thermal: int340x: processor_thermal: Add RFIM driver
thermal: int340x: processor_thermal: Add AlderLake PCI device id
thermal: int340x: processor_thermal: Refactor MMIO interface
thermal: rcar_gen3_thermal: Add r8a779a0 support
dt-bindings: thermal: rcar-gen3-thermal: Add r8a779a0 support
platform/x86/drivers/acerhdf: Check the interval value when it is set
platform/x86/drivers/acerhdf: Use module_param_cb to set/get polling interval
...
Prevent build failure if the option CONFIG_ENERGY_MODEL is not set. The
devfreq cooling is able to operate without the Energy Model.
Don't use dev->em_pd directly and use local pointer.
Fixes: 615510fe13 ("thermal: devfreq_cooling: remove old power model and use EM")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201215154221.8828-1-lukasz.luba@arm.com
The ops is only showing a trace telling a critical trip point is
crossed. The same information is given by the thermal framework.
This is redundant, remove the code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20201210121514.25760-4-daniel.lezcano@linaro.org
Currently there is no way to the sensors to directly call an ops in
interrupt mode without calling thermal_zone_device_update assuming all
the trip points are defined.
A sensor may want to do something special if a trip point is hot or
critical.
This patch adds the critical and hot ops to the thermal zone device,
so a sensor can directly invoke them or let the thermal framework to
call the sensor specific ones.
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20201210121514.25760-2-daniel.lezcano@linaro.org
The actual code is silently ignoring a thermal zone update when a
driver is requesting it without a get_temp ops set.
That looks not correct, as the caller should not have called this
function if the thermal zone is unable to read the temperature.
That makes the code less robust as the check won't detect the driver
is inconsistently using the thermal API and that does not help to
improve the framework as these circumvolutions hide the problem at the
source.
In order to detect the situation when it happens, let's add a warning
when the update is requested without the get_temp() ops set.
Any warning emitted will have to be fixed at the source of the
problem: the caller must not call thermal_zone_device_update if there
is not get_temp callback set.
Cc: Thara Gopinath <thara.gopinath@linaro.org>
Cc: Amit Kucheria <amitk@kernel.org>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20201210121514.25760-1-daniel.lezcano@linaro.org
Remove old power model and use new Energy Model to calculate the power
budget. It drops static + dynamic power calculations and power table
in order to use Energy Model performance domain data. This model
should be easy to use and could find more users. It is also less
complicated to setup the needed structures.
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210143014.24685-5-lukasz.luba@arm.com
The Energy Model (EM) framework supports devices such as Devfreq. Create
new registration function which automatically register EM for the thermal
devfreq_cooling devices. This patch prepares the code for coming changes
which are going to replace old power model with the new EM.
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210143014.24685-4-lukasz.luba@arm.com
Devfreq cooling needs to now the correct status of the device in order
to operate. Devfreq framework can change the device status in the
background. To mitigate issues make a copy of the status structure and use
it for internal calculations.
In addition this patch adds normalization function, which also makes sure
that whatever data comes from the device, the load will be in range from 1
to 1024.
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210143014.24685-3-lukasz.luba@arm.com
Prepare for deleting the static and dynamic power calculation and clean
the trace function. These two fields are going to be removed in the next
changes.
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> # for tracing code
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210143014.24685-2-lukasz.luba@arm.com
Use macro for temperature calculation
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210124801.13850-1-sumeet.r.pawnikar@intel.com
Added processor thermal device mail box interface for workload hints
setting. These hints will give indication to hardware to better manage
power and thermals. The supported hints are:
idle
semi_active
burusty
sustained
battery_life
For example when the system is on battery, the hardware can be less
aggressive in power ramp up.
This will create an attribute group at
/sys/bus/pci/devices/0000:00:04.0/workload_request
This folder contains two attributes:
workload_available_types : (RO): This shows available workload types
workload_type: (RW) : Allows to set and get current workload type
setting
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-4-srinivas.pandruvada@linux.intel.com
Add support for RFIM (Radio Frequency Interference Mitigation) support
via processor thermal PCI device. This drivers allows adjustment of
FIVR (Fully Integrated Voltage Regulator) and DDR (Double Data Rate)
frequencies to avoid RF interference with WiFi and 5G.
Switching voltage regulators (VR) generate radiated EMI or RFI at the
fundamental frequency and its harmonics. Some harmonics may interfere
with very sensitive wireless receivers such as Wi-Fi and cellular that
are integrated into host systems like notebook PCs. One of mitigation
methods is requesting SOC integrated VR (IVR) switching frequency to a
small % and shift away the switching noise harmonic interference from
radio channels. OEM or ODMs can use the driver to control SOC IVR
operation within the range where it does not impact IVR performance.
DRAM devices of DDR IO interface and their power plane can generate EMI
at the data rates. Similar to IVR control mechanism, Intel offers a
mechanism by which DDR data rates can be changed if several conditions
are met: there is strong RFI interference because of DDR; CPU power
management has no other restriction in changing DDR data rates;
PC ODMs enable this feature (real time DDR RFI Mitigation referred to as
DDR-RFIM) for Wi-Fi from BIOS.
This change exports two folders under /sys/bus/pci/devices/0000:00:04.0.
One folder "fivr" contains all attributes exposed for controling FIVR
features. The other folder "dvfs" contains all attributes for DDR
features.
Changes done to implement:
- New module for rfim interfaces
- Two new per processor features for DDR and FIVR
- Enable feature for Tiger Lake (FIVR only) and Alder Lake
The attributes exposed and explanation:
FIVR attributes
vco_ref_code_lo (RW): The VCO reference code is an 11-bit field and
controls the FIVR switching frequency. This is the 3-bit LSB field.
vco_ref_code_hi (RW): The VCO reference code is an 11-bit field and
controls the FIVR switching frequency. This is the 8-bit MSB field.
spread_spectrum_pct (RW): Set the FIVR spread spectrum clocking
percentage
spread_spectrum_clk_enable (RW): Enable/disable of the FIVR spread
spectrum clocking feature
rfi_vco_ref_code (RW): This field is a read only status register which
reflects the current FIVR switching frequency
fivr_fffc_rev (RW): This field indicated the revision of the FIVR HW.
DVFS attributes
rfi_restriction_run_busy (RW): Request the restriction of specific DDR
data rate and set this value 1. Self reset to 0 after operation.
rfi_restriction_err_code (RW): Values: 0 :Request is accepted, 1:Feature
disabled, 2: the request restricts more points than it is allowed
rfi_restriction_data_rate_Delta (RW): Restricted DDR data rate for RFI
protection: Lower Limit
rfi_restriction_data_rate_Base (RW): Restricted DDR data rate for RFI
protection: Upper Limit
ddr_data_rate_point_0 (RO): DDR data rate selection 1st point
ddr_data_rate_point_1 (RO): DDR data rate selection 2nd point
ddr_data_rate_point_2 (RO): DDR data rate selection 3rd point
ddr_data_rate_point_3 (RO): DDR data rate selection 4th point
rfi_disable (RW): Disable DDR rate change feature
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-3-srinivas.pandruvada@linux.intel.com
Added AlderLake PCI device id to support processor thermal driver. Reuse
the feature set (just includes RAPL) from previous generations.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-2-srinivas.pandruvada@linux.intel.com
The Processor Thermal PCI device supports multiple features. Currently
we export only RAPL. But we need more features from this device exposed
for Tiger Lake and Alder Lake based platforms. So re-structure the
current MMIO interface, so that more features can be added cleanly.
No functional changes are expected with this change.
Changes done in this patch:
- Using PCI_DEVICE_DATA(), hence names of defines changed
- Move RAPL MMIO code to its own module
- Move the RAPL MMIO offsets to RAPL MMIO module
- Adjust Kconfig dependency of PROC_THERMAL_MMIO_RAPL
- Per processor driver data now contains the supported features
- Moved all the common data structures and defines to a common header
file
- This new header file contains all the processor_thermal_* interfaces
- Based on the features supported the module interface is called
- Each module atleast provides one add and one remove function
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-1-srinivas.pandruvada@linux.intel.com
Currently the error message does not print the correct error code.
Fix it by initializing 'ret' to the proper error code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201202232448.2692-1-festevam@gmail.com
Remove the usage of interrupts for the normal temperature operation and
depend on the polling performed by the thermal core. This is done to
prepare to use the interrupts as they are intended to trigger once
specific trip points are passed and not to react to temperature changes
in the normal operational range.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126220923.3107213-1-niklas.soderlund+renesas@ragnatech.se
The only usage of these structs is to assign their address to the
thermal_zone_attribute_groups array, which consists of pointers to
const, so make them const to allow the compiler to put them in read-only
memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201128234342.36684-1-rikard.falkeborn@gmail.com
The PID coefficients should be estimated again when there was a change to
sustainable power value made by user. This change removes unused argument
'force' and makes the function ready for such updates.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201124161025.27694-4-lukasz.luba@arm.com
The sustainable power value might come from the Device Tree or can be
estimated in run time. The sustainable power might be updated by the user
via sysfs interface, which should trigger new estimation of PID
coefficients. There is no need to estimate it every time when the
governor is called and temperature is high. Instead, store the estimated
value and make it available via standard sysfs interface, so it can be
checked from the user-space.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201124161025.27694-3-lukasz.luba@arm.com
Intelligent Power Allocation (IPA) is built around the PID controller
concept. The initialization code tries to setup the environment based on
the information available in DT or estimate the value based on minimum
power reported by each of the cooling device. The estimation will have an
impact on the PID controller behaviour via the related 'k_po', 'k_pu',
'k_i' coefficients and also on the power budget calculation.
This change prevents the situation when 'k_i' is relatively big compared
to 'k_po' and 'k_pu' values. This might happen when the estimation for
'sustainable_power' returned small value, thus 'k_po' and 'k_pu' are
small.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201124161025.27694-2-lukasz.luba@arm.com
The reference to acpi_gbl_FADT causes a build error when ACPI is not
enabled. Fix by making that conditional on CONFIG_ACPI.
../drivers/thermal/intel/intel_pch_thermal.c: In function 'pch_wpt_suspend':
../drivers/thermal/intel/intel_pch_thermal.c:217:8: error: 'acpi_gbl_FADT' undeclared (first use in this function); did you mean 'acpi_get_type'?
if (!(acpi_gbl_FADT.flags & ACPI_FADT_LOW_POWER_S0))
^~~~~~~~~~~~~
Fixes: ef63b043ac ("thermal: intel: pch: fix S0ix failure due to PCH temperature above threshold")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Amit Kucheria <amitk@kernel.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201117023807.8266-1-rdunlap@infradead.org
Many monitoring tools read the CPU temperature using the hwmon
interface. Expose the thermal sensors on Amlogic boards as hwmon
devices.
Without this lm_sensors' "sensors" tool does not find any temperature
sensors. Now it prints:
cpu_thermal-virtual-0
Adapter: Virtual device
temp1: +44.7 C (crit = +110.0 C)
ddr_thermal-virtual-0
Adapter: Virtual device
temp1: +45.9 C (crit = +110.0 C)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201115190658.631578-1-martin.blumenstingl@googlemail.com
I noticed that I couldn't read the PCH temperature on my workstation
(C620 series chipset, w/ 2x Xeon Gold 5215 CPUs) directly, but had to go
through IPMI. Looking at the data sheet, it looks to me like the
existing intel PCH thermal driver should work without changes for
Lewisburg.
I suspect there's some other PCI IDs missing. But I hope somebody at
Intel would have an easier time figuring that out than I...
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/lkml/20200115184415.1726953-1-andres@anarazel.de/
Signed-off-by: Andres Freund <andres@anarazel.de>
Reviewed-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201113204916.1144907-1-andres@anarazel.de
It has been observed that on OMAP4430 (ES2.0, ES2.1 and ES2.3) the enabled
notifier causes errors on the DTEMP readout values:
ti-soc-thermal 4a002260.bandgap: in range ADC val: 52
ti-soc-thermal 4a002260.bandgap: in range ADC val: 64
ti-soc-thermal 4a002260.bandgap: in range ADC val: 64
ti-soc-thermal 4a002260.bandgap: out of range ADC val: 0
thermal thermal_zone0: failed to read out thermal zone (-5)
ti-soc-thermal 4a002260.bandgap: out of range ADC val: 0
thermal thermal_zone0: failed to read out thermal zone (-5)
ti-soc-thermal 4a002260.bandgap: out of range ADC val: 4
thermal thermal_zone0: failed to read out thermal zone (-5)
ti-soc-thermal 4a002260.bandgap: in range ADC val: 100
raw 100 translates to 133 Celsius on omap4-sdp, triggering shutdown due to
critical temperature.
When the notifier is disable for OMAP4430 the DTEMP values are stable:
ti-soc-thermal 4a002260.bandgap: in range ADC val: 56
ti-soc-thermal 4a002260.bandgap: in range ADC val: 56
ti-soc-thermal 4a002260.bandgap: in range ADC val: 57
ti-soc-thermal 4a002260.bandgap: in range ADC val: 57
ti-soc-thermal 4a002260.bandgap: in range ADC val: 56
Fixes: 5093402e5b ("thermal: ti-soc-thermal: Enable addition power management")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201029100335.27665-1-peter.ujfalusi@ti.com
If state has not changed successfully and we updated cpufreq_state,
next time when the new state is equal to cpufreq_state (not changed
successfully last time), we will return directly and miss a
freq_qos_update_request() that should have been.
Fixes: 5130802ddb ("thermal: cpu_cooling: Switch to QoS requests for freq limits")
Cc: v5.4+ <stable@vger.kernel.org> # v5.4+
Signed-off-by: Zhuguangqing <zhuguangqing@xiaomi.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201106092243.15574-1-zhuguangqing83@gmail.com
Function thermal_add_hwmon_sysfs, hwmon will be NULL when
new_hwmon_device = 0, so there is no need to check, kfree will
handle NULL point.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201102023121.3312-1-bernard@vivo.com
The bitmap_* API is the standard way to access data in the bitfield.
So convert irq_ack to return an unsigned long, and make things to use
bitmap API.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201109114624.23035-1-frank@allwinnertech.com
When system tries to enter S0ix suspend state, just after active load
scenarios, it fails due to PCH current temperature is higher than set
threshold.
This patch introduces delay loop mechanism that allows PCH temperature
to go down below threshold during suspend so it won't fail to enter S0ix.
Add delay loop timeout and count as module parameters for user to tune it,
if required based on system design. This change notifies the different
warning messages like when PCH temperature above the threshold and
executing delay loop. Also, notify the messages when it success or
failure for S0ix entry.
Previously out of 1000 runs around 3 to 5 times it might fail to enter
S0ix just after heavy workload. With this change, S0ix failures reduced
as PCH cools down below threshold.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201106170633.20838-1-sumeet.r.pawnikar@intel.com
MT8516 does not support thermal reset. Use device_reset_optional
instead of device_reset.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201021164231.3029956-3-fparent@baylibre.com
On RT or even on mainline with 'threadirqs' on the command line all
interrupts which are not explicitly requested with IRQF_NO_THREAD
run their handlers in thread context. The same applies to soft interrupts.
That means they are subject to the normal scheduler rules and no other
code is going to acquire that lock from hard interrupt context either,
so the irqsave() here is pointless in all cases.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1603760790-37748-1-git-send-email-tiantao6@hisilicon.com
The trip points are checked one by one with multiple condition
branches where one condition is enough to disable the trip point.
Merge all these conditions in a single 'OR' statement.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201027013743.62392-1-bernard@vivo.com
[dlezcano] Changed patch description
Since the power actor section has one function power_actor_set_power()
move it into Intelligent Power Allocation (IPA). There is no other user
of that helper function. It would also allow to remove the check of
cdev_is_power_actor() because the code which calls it in IPA already does
the needed check. Make the function static since only IPA use it.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201015112441.4056-5-lukasz.luba@arm.com
Since the Intelligent Power Allocation (IPA) uses different way to get
minimum and maximum power for a given cooling device, the helper functions
are not needed. There is no other code which uses them, so remove the
helper functions.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201015112441.4056-4-lukasz.luba@arm.com
The thermal cooling device specified in DT might be instantiated for
a thermal zone trip point with a limited set of OPPs to operate on. This
configuration should be supported by Intelligent Power Allocation (IPA),
since it is a standard for other governors. Change the code and allow IPA
to get power value of lower and upper bound set for a given cooling
device.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201015112441.4056-3-lukasz.luba@arm.com
The upper and lower limits of thermal throttle state in the
DT do not apply to the Intelligent Power Allocation (IPA) governor.
Add the clamping for cooling device upper and lower limits in the
power_actor_set_power() used by IPA.
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201007024332.30322-1-michael.kao@mediatek.com
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Conversion done using the script at:
https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.pl
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use dev_error_probe() to simplify the error handling on imx and imx8
platforms (Anson Huang)
- Use dedicated kobj_to_dev() instead of container_of() in the sysfs
core code (Tian Tao)
- Fix coding style by adding braces to a one line conditional
statement on rcar (Geert Uytterhoeven)
- Add DT binding documentation for the r8a774e1 platform and update
the Kconfig description supporting RZ/G2 SoCs (Lad Prabhakar)
- Simplify the return expression of stm_thermal_prepare on the stm32
platform (Qinglang Miao)
- Fix the unit in the function documentation for the idle injection
cooling device (Zhuguang Qing)
- Remove an unecessary mutex_init() in the core code (Qinglang Miao)
- Add support for keep alive events in the core code and the specific
int340x (Srinivas Pandruvada)
- Remove unused thermal zone variable in devfreq and cpufreq cooling
devices (Zhuguang Qing)
- Add the A100's THS controller support (Yangtao Li)
- Add power management on the omap3's bandgap sensor (Adam Ford)
- Fix a missing nlmsg_free in the netlink core error path (Jing Xiangfeng)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl+GwbYACgkQqDIjiipP
6E8IFAf/UnO1HqfK96FnVJXx5ClXFE8PQhdVejxBEsNCJqUOwlqfpyONy7mgwABb
EuOvp5ZLX6ly9xG6J4NJhE4gN4DxqRKe0S3bQMU+DX8TQHc3otDKHILJbHrJdOY+
BYZpGxuCjU9yZrsJopztZIcpG7cF78d39XCJVSrBhoOBqPLXNGZkUUzOv9+QQti3
ipdhqB3kUzkgDFgIrDxX8t0vybQZSbiRWNUGrw/WQjMsG0NGIarCUHW4wiaea6gU
L2x1QDR5h9hxEAJiTBarOtF7ZlE15fpria0mWfTgmNMArMEtRBL60kBnmYa4o3EG
CseR7x1MdTCSqLCzKGfQyKv5SFgnVg==
=P6zv
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Fix Kconfig typo "acces" -> "access" (Colin Ian King)
- Use dev_error_probe() to simplify the error handling on imx and imx8
platforms (Anson Huang)
- Use dedicated kobj_to_dev() instead of container_of() in the sysfs
core code (Tian Tao)
- Fix coding style by adding braces to a one line conditional statement
on rcar (Geert Uytterhoeven)
- Add DT binding documentation for the r8a774e1 platform and update the
Kconfig description supporting RZ/G2 SoCs (Lad Prabhakar)
- Simplify the return expression of stm_thermal_prepare on the stm32
platform (Qinglang Miao)
- Fix the unit in the function documentation for the idle injection
cooling device (Zhuguang Qing)
- Remove an unecessary mutex_init() in the core code (Qinglang Miao)
- Add support for keep alive events in the core code and the specific
int340x (Srinivas Pandruvada)
- Remove unused thermal zone variable in devfreq and cpufreq cooling
devices (Zhuguang Qing)
- Add the A100's THS controller support (Yangtao Li)
- Add power management on the omap3's bandgap sensor (Adam Ford)
- Fix a missing nlmsg_free in the netlink core error path (Jing
Xiangfeng)
* tag 'thermal-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
thermal: core: Adding missing nlmsg_free() in thermal_genl_sampling_temp()
thermal: ti-soc-thermal: Enable addition power management
thermal: sun8i: Add A100's THS controller support
thermal: sun8i: add TEMP_CALIB_MASK for calibration data in sun50i_h6_ths_calibrate
dt-bindings: thermal: sun8i: Add binding for A100's THS controller
thermal: cooling: Remove unused variable *tz
thermal: int340x: Add keep alive response method
thermal: core: Add new event for sending keep alive notifications
thermal: int340x: Provide notification for OEM variable change
thermal: core: remove unnecessary mutex_init()
thermal/idle_inject: Fix comment of idle_duration_us and name of latency_ns
thermal: Kconfig: Update description for RCAR_GEN3_THERMAL config
thermal: stm32: simplify the return expression of stm_thermal_prepare()
dt-bindings: thermal: rcar-gen3-thermal: Add r8a774e1 support
thermal: rcar_thermal: Add missing braces to conditional statement
thermal: Use kobj_to_dev() instead of container_of()
thermal: imx8mm: Use dev_err_probe() to simplify error handling
thermal: imx: Use dev_err_probe() to simplify error handling
drivers: thermal: Kconfig: fix spelling mistake "acces" -> "access"
thermal_genl_sampling_temp() misses to call nlmsg_free() in an error path.
Jump to out_free to fix it.
Fixes: 1ce50e7d40 ("thermal: core: genetlink support for events/cmd/sampling")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200929082652.59876-1-jingxiangfeng@huawei.com
The bandgap sensor can be idled when the processor is too, but it
isn't currently being done, so the power consumption of OMAP3
boards can elevated if the bangap sensor is enabled.
This patch attempts to use some additional power management
to idle the clock to the bandgap when not needed.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Andreas Kemnade <andreas@kemnade.info> # GTA04
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200911123157.759379-1-aford173@gmail.com
For sun50i_h6_ths_calibrate(), the data read from nvmem needs a round of
calculation. On the other hand, the newer SOC may store other data in
the space other than 12bit sensor data. Add mask operation to read data
to avoid conversion error.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/dcf98648c16aff7649ff82438bfce6caae3e176f.1595572867.git.frank@allwinnertech.com
1. devfreq_cooling.c: The variable *tz is not used in
devfreq_cooling_get_requested_power(), devfreq_cooling_state2power()
and devfreq_cooling_power2state().
2. cpufreq_cooling.c: After 84fe2cab48, the variable *tz is not used
anymore in cpufreq_get_requested_power(), cpufreq_state2power() and
cpufreq_power2state().
Remove the variable *tz.
Signed-off-by: zhuguangqing <zhuguangqing@xiaomi.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200914071101.13575-1-zhuguangqing83@gmail.com
When firmware requests keep alive response, send an event to user space
to confirm by using imok sysfs entry.
Create a new sysf entry called "imok". User space can write an integer,
which results in execution of IMOK ACPI method of INT3400 thermal zone
device. This results in sending response to firmware request for keep
alive.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200915223650.406046-4-srinivas.pandruvada@linux.intel.com
When we receive ACPI notification for OEM variable change pass the
notification to user space handler. This will avoid polling for
OEM variable change from user space.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200915223650.406046-2-srinivas.pandruvada@linux.intel.com
The mutex poweroff_lock is initialized statically. It is
unnecessary to initialize by mutex_init().
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200916062139.191233-1-miaoqinglang@huawei.com
According to Documentation/process/coding-style.rst, if one branch of a
conditional statement needs braces, both branches should use braces.
Fixes: bbcf90c064 ("thermal: Explicitly enable non-changing thermal zone devices")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200819092716.3191-1-geert+renesas@glider.be
dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1597129185-8460-2-git-send-email-Anson.Huang@nxp.com
dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1597129185-8460-1-git-send-email-Anson.Huang@nxp.com
Bulk of the genetlink users can use smaller ops, move them.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to add maxattr and policy back to genl_ops, to enable
dumping per command policy to user space. This, however, would
cause bloat for all the families with global policies. Introduce
smaller version of ops (half the size of genl_ops). Translate
these smaller ops into a full blown struct before use in the
core.
v1:
- use struct assignment
- put a full copy of the op in struct genl_dumpit_info
- s/light/small/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
resulting from an incorrect ADC conversion are too high and fire an
emergency shutdown (Tony Lindgren)
- Don't suppress negative temp for qcom spmi as they are valid and
userspace needs them (Veera Vegivada)
- Fix use-after-free in thermal_zone_device_unregister reported by
Kasan (Dmitry Osipenko)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl9SDqQACgkQqDIjiipP
6E9/qwf/WybOihgjeQUv3a9f4k6SeJphoDZRNATJtyU1e+fgJXUxjFqma6t4CYJv
uphZ1SppY9rnx1nWzhANSQjKun5KLwIskcNTCaGN4adRJ1cNdY63PdSX9BTJr9+H
w5H0AGWMErAOdmCPCro4pnZ3l3FPKXcoNvqDAjF1kZ97v5tMGzdInflOJl1ztUZA
scAnY7j0TyNsoRy2TV0oxQtSN9cDhgph1zJF1RcVzlU1uD897Htet1RF/PrHDvBW
NYVcWDTfiWmvf9Zewy2+cfApK9QGqBRhnwt4Z8PlTUcqrOgqAiNnOAnov+Topg/y
XNQzWwXFUip6bk5pTXPF8gSI0glkJg==
=LDGk
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal fixes from Daniel Lezcano:
- Fix bogus thermal shutdowns for omap4430 where bogus values resulting
from an incorrect ADC conversion are too high and fire an emergency
shutdown (Tony Lindgren)
- Don't suppress negative temp for qcom spmi as they are valid and
userspace needs them (Veera Vegivada)
- Fix use-after-free in thermal_zone_device_unregister reported by
Kasan (Dmitry Osipenko)
* tag 'thermal-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
thermal: core: Fix use-after-free in thermal_zone_device_unregister()
thermal: qcom-spmi-temp-alarm: Don't suppress negative temp
thermal: ti-soc-thermal: Fix bogus thermal shutdowns for omap4430
The user-after-free bug in thermal_zone_device_unregister() is reported by
KASAN. It happens because struct thermal_zone_device is released during of
device_unregister() invocation, and hence the "tz" variable shouldn't be
touched by thermal_notify_tz_delete(tz->id).
Fixes: 55cdf0a283 ("thermal: core: Add notifications call in the framework")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200817235854.26816-1-digetx@gmail.com
Currently driver is suppressing the negative temperature
readings from the vadc. Consumers of the thermal zones need
to read the negative temperature too. Don't suppress the
readings.
Fixes: c610afaa21 ("thermal: Add QPNP PMIC temperature alarm driver")
Signed-off-by: Veera Vegivada <vvegivad@codeaurora.org>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/944856eb819081268fab783236a916257de120e4.1596040416.git.gurus@codeaurora.org
We can sometimes get bogus thermal shutdowns on omap4430 at least with
droid4 running idle with a battery charger connected:
thermal thermal_zone0: critical temperature reached (143 C), shutting down
Dumping out the register values shows we can occasionally get a 0x7f value
that is outside the TRM listed values in the ADC conversion table. And then
we get a normal value when reading again after that. Reading the register
multiple times does not seem help avoiding the bogus values as they stay
until the next sample is ready.
Looking at the TRM chapter "18.4.10.2.3 ADC Codes Versus Temperature", we
should have values from 13 to 107 listed with a total of 95 values. But
looking at the omap4430_adc_to_temp array, the values are off, and the
end values are missing. And it seems that the 4430 ADC table is similar
to omap3630 rather than omap4460.
Let's fix the issue by using values based on the omap3630 table and just
ignoring invalid values. Compared to the 4430 TRM, the omap3630 table has
the missing values added while the TRM table only shows every second
value.
Note that sometimes the ADC register values within the valid table can
also be way off for about 1 out of 10 values. But it seems that those
just show about 25 C too low values rather than too high values. So those
do not cause a bogus thermal shutdown.
Fixes: 1a31270e54 ("staging: omap-thermal: add OMAP4 data structures")
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200706183338.25622-1-tony@atomide.com
- Make better attempt at matching device with the correct OF node
- Allow batch removal of hierarchical sub-devices
- New Drivers
- Add STM32 Clocksource driver
- Add support for Khadas System Control Microcontroller
- Driver Removal
- Remove unused driver for TI's SMSC ECE1099
- New Device Support
- Add support for Intel Emmitsburg PCH to Intel LPSS PCI
- Add support for Intel Tiger Lake PCH-H to Intel LPSS PCI
- Add support for Dialog DA revision to Dialog DA9063
- New Functionality
- Add support for AXP803 to be probed by I2C
- Fix-ups
- Numerous W=1 warning fixes
- Device Tree changes; stm32-lptimer, gateworks-gsc, khadas,mcu, stmfx, cros-ec, j721e-system-controller
- Enabled Regmap 'fast I/O'; stm32-lptimer
- Change BUG_ON to WARN_ON; arizona-core
- Remove superfluous code/initialisation; madera, max14577
- Trivial formatting/spelling issues; madera-core, madera-i2c, da9055, max77693-private
- Switch to of_platform_populate(); sprd-sc27xx-spi
- Expand out set/get brightness/pwm macros; lm3533-ctrlbank
- Disable IRQs on suspend; motorola-cpcap
- Clean-up error handling; intel_soc_pmic_mrfld
- Ensure correct removal order of sub-devices; madera
- Many s/HTTP/HTTPS/ link changes
- Ensure name used with Regmap is unique; syscon
- Bug Fixes
- Properly 'put' clock on unbind and error; arizona-core
- Fix revision handling; da9063
- Fix 'assignment of read-only location' error; kempld-core
- Avoid using the Regmap API when atomic; rn5t618
- Redefine volatile register description; rn5t618
- Use locking to protect event handler; dln2
-----BEGIN PGP SIGNATURE-----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=X/Zn
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks
- Make better attempt at matching device with the correct OF node
- Allow batch removal of hierarchical sub-devices
New Drivers
- Add STM32 Clocksource driver
- Add support for Khadas System Control Microcontroller
Driver Removal
- Remove unused driver for TI's SMSC ECE1099
New Device Support
- Add support for Intel Emmitsburg PCH to Intel LPSS PCI
- Add support for Intel Tiger Lake PCH-H to Intel LPSS PCI
- Add support for Dialog DA revision to Dialog DA9063
New Functionality
- Add support for AXP803 to be probed by I2C
Fix-ups
- Numerous W=1 warning fixes
- Device Tree changes (stm32-lptimer, gateworks-gsc, khadas,mcu, stmfx, cros-ec, j721e-system-controller)
- Enabled Regmap 'fast I/O' in stm32-lptimer
- Change BUG_ON to WARN_ON in arizona-core
- Remove superfluous code/initialisation (madera, max14577)
- Trivial formatting/spelling issues (madera-core, madera-i2c, da9055, max77693-private)
- Switch to of_platform_populate() in sprd-sc27xx-spi
- Expand out set/get brightness/pwm macros in lm3533-ctrlbank
- Disable IRQs on suspend in motorola-cpcap
- Clean-up error handling in intel_soc_pmic_mrfld
- Ensure correct removal order of sub-devices in madera
- Many s/HTTP/HTTPS/ link changes
- Ensure name used with Regmap is unique in syscon
Bug Fixes
- Properly 'put' clock on unbind and error in arizona-core
- Fix revision handling in da9063
- Fix 'assignment of read-only location' error in kempld-core
- Avoid using the Regmap API when atomic in rn5t618
- Redefine volatile register description in rn5t618
- Use locking to protect event handler in dln2"
* tag 'mfd-next-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (76 commits)
mfd: syscon: Use a unique name with regmap_config
mfd: Replace HTTP links with HTTPS ones
mfd: dln2: Run event handler loop under spinlock
mfd: madera: Improve handling of regulator unbinding
mfd: mfd-core: Add mechanism for removal of a subset of children
mfd: intel_soc_pmic_mrfld: Simplify the return expression of intel_scu_ipc_dev_iowrite8()
mfd: max14577: Remove redundant initialization of variable current_bits
mfd: rn5t618: Fix caching of battery related registers
mfd: max77693-private: Drop a duplicated word
mfd: da9055: pdata.h: Drop a duplicated word
mfd: rn5t618: Make restart handler atomic safe
mfd: kempld-core: Fix 'assignment of read-only location' error
mfd: axp20x: Allow the AXP803 to be probed by I2C
mfd: da9063: Add support for latest DA silicon revision
mfd: da9063: Fix revision handling to correctly select reg tables
dt-bindings: mfd: st,stmfx: Remove I2C unit name
dt-bindings: mfd: ti,j721e-system-controller.yaml: Add J721e system controller
mfd: motorola-cpcap: Disable interrupt for suspend
mfd: smsc-ece1099: Remove driver
mfd: core: Add OF_MFD_CELL_REG() helper
...
We just don't do that. "default y" is for things that are needed for
compatibility (when an old feature is made unconditional), or for things
that are basically part of the infrastructure of a platform.
And it can possibly be used for questions that don't enable code on
their own, but are used to enable or disable a whole slew of other
questions.
A new feature that people aren't using is never 'default y', unless it
cures cancer or ends world hunger.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers cleanup (Andrzej Pietrasiewicz)
- Add generic netlink support for userspace notifications: events, temperature
and discovery commands (Daniel Lezcano)
- Fix redundant initialization for a ret variable (Colin Ian King)
- Remove the clock cooling code as it is used nowhere (Amit Kucheria)
- Add the rcar_gen3_thermal's r8a774e1 support (Marian-Cristian Rotariu)
- Replace all references to thermal.txt in the documentation to the
corresponding yaml files (Amit Kucheria)
- Add maintainer entry for the IPA (Lukasz Luba)
- Add support for MSM8939 for the tsens (Shawn Guo)
- Update power allocator and devfreq cooling to SPDX licensing (Lukasz Luba)
- Add Cannon Lake Low Power PCH support (Sumeet Pawnikar)
- Add tsensor support for V2 mediatek thermal system (Henry Yen)
- Fix thermal zone lookup by ID for the core code (Thierry Reding)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl8q7tsACgkQqDIjiipP
6E+5Rwf7BFEn5YXPvng8cmnAlgvEBc9DdT6mGSo0NpFm9MdUxXlaqvw3WWSGyqWQ
+z0Ka7lmn5XyiMsVN11++Snp+79X17HzZf9SXO3glyIpAn+5prTDRhzzj0/jPrtS
sEeI++DrILsKKMGVljzftLmwNJN9DkUDNcnmWmZdCDbYVEKtP9Pjf2wBjAnXj7sX
JA3CkHRMwYLEQbfaKz37M11cYM+LqbDOlb6U11YWgAGGJ7d7zNYRf2/YSYPM4AN6
iE6j0E+3jIlXesULsap1AzeJaBq+wFxj1FL2TUZ8KscvRrm3AucqzNAT2M/Bc5Az
XLKKzc6Gp9JfqB5KXhX2EDu7VRnDBg==
=cSMN
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Add support to enable/disable the thermal zones resulting on core
code and drivers cleanup (Andrzej Pietrasiewicz)
- Add generic netlink support for userspace notifications: events,
temperature and discovery commands (Daniel Lezcano)
- Fix redundant initialization for a ret variable (Colin Ian King)
- Remove the clock cooling code as it is used nowhere (Amit Kucheria)
- Add the rcar_gen3_thermal's r8a774e1 support (Marian-Cristian
Rotariu)
- Replace all references to thermal.txt in the documentation to the
corresponding yaml files (Amit Kucheria)
- Add maintainer entry for the IPA (Lukasz Luba)
- Add support for MSM8939 for the tsens (Shawn Guo)
- Update power allocator and devfreq cooling to SPDX licensing (Lukasz
Luba)
- Add Cannon Lake Low Power PCH support (Sumeet Pawnikar)
- Add tsensor support for V2 mediatek thermal system (Henry Yen)
- Fix thermal zone lookup by ID for the core code (Thierry Reding)
* tag 'thermal-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (40 commits)
thermal: intel: intel_pch_thermal: Add Cannon Lake Low Power PCH support
thermal: mediatek: Add tsensor support for V2 thermal system
thermal: mediatek: Prepare to add support for other platforms
thermal: Update power allocator and devfreq cooling to SPDX licensing
MAINTAINERS: update entry to thermal governors file name prefixing
thermal: core: Add thermal zone enable/disable notification
thermal: qcom: tsens-v0_1: Add support for MSM8939
dt-bindings: tsens: qcom: Document MSM8939 compatible
thermal: core: Fix thermal zone lookup by ID
thermal: int340x: processor_thermal: fix: update Jasper Lake PCI id
thermal: imx8mm: Support module autoloading
thermal: ti-soc-thermal: Fix reversed condition in ti_thermal_expose_sensor()
MAINTAINERS: Add maintenance information for IPA
thermal: rcar_gen3_thermal: Do not shadow thcode variable
dt-bindings: thermal: Get rid of thermal.txt and replace references
thermal: core: Move initialization after core initcall
thermal: netlink: Improve the initcall ordering
net: genetlink: Move initialization to core_initcall
thermal: rcar_gen3_thermal: Add r8a774e1 support
thermal/drivers/clock_cooling: Remove clock_cooling code
...
static priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low' priority level,
plus sched_set_normal() to set the policy back to non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in a separate
tree.
When merging to the latest upstream tree there's a conflict in drivers/spi/spi.c,
which can be resolved via:
sched_set_fifo(ctlr->kworker_task);
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/7JH
-----END PGP SIGNATURE-----
Merge tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched/fifo updates from Ingo Molnar:
"This adds the sched_set_fifo*() encapsulation APIs to remove static
priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low'
priority level, plus sched_set_normal() to set the policy back to
non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in
a separate tree"
* tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched,tracing: Convert to sched_set_fifo()
sched: Remove sched_set_*() return value
sched: Remove sched_setscheduler*() EXPORTs
sched,psi: Convert to sched_set_fifo_low()
sched,rcutorture: Convert to sched_set_fifo_low()
sched,rcuperf: Convert to sched_set_fifo_low()
sched,locktorture: Convert to sched_set_fifo()
sched,irq: Convert to sched_set_fifo()
sched,watchdog: Convert to sched_set_fifo()
sched,serial: Convert to sched_set_fifo()
sched,powerclamp: Convert to sched_set_fifo()
sched,ion: Convert to sched_set_normal()
sched,powercap: Convert to sched_set_fifo*()
sched,spi: Convert to sched_set_fifo*()
sched,mmc: Convert to sched_set_fifo*()
sched,ivtv: Convert to sched_set_fifo*()
sched,drm/scheduler: Convert to sched_set_fifo*()
sched,msm: Convert to sched_set_fifo*()
sched,psci: Convert to sched_set_fifo*()
sched,drbd: Convert to sched_set_fifo*()
...
* pm-em:
OPP: refactor dev_pm_opp_of_register_em() and update related drivers
Documentation: power: update Energy Model description
PM / EM: change name of em_pd_energy to em_cpu_energy
PM / EM: remove em_register_perf_domain
PM / EM: add support for other devices than CPUs in Energy Model
PM / EM: update callback structure and add device pointer
PM / EM: introduce em_dev_register_perf_domain function
PM / EM: change naming convention from 'capacity' to 'performance'
* pm-core:
mmc: jz4740: Use pm_ptr() macro
PM: Make *_DEV_PM_OPS macros use __maybe_unused
PM: core: introduce pm_ptr() macro
This patch adds full support for ver 2 thermal system (e.g., MT7622 SoC).
The new changes include reading calibration data, converting temperature
and hardware initialization which are specific for version 2 system.
Each platform decides which function to call according to its version.
Fixes: 3966be3c08 ("thermal: mediatek: add support for MT7622 SoC")
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1588238074-19338-3-git-send-email-henry.yen@mediatek.com
It is known that Mediatek owns two thermal systems, which only differ
in the way of reading calibration data and converting temperature.
MT8173, MT8183, MT2701 and MT2712 belongs to version 1 thermal
system, and MT7622 belongs to version 2.
In order to handle both systems, the suffix _V1 is appended to the
current code, and then the second patch will add _V2 functions with
the same purpose but different implementation.
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1588238074-19338-2-git-send-email-henry.yen@mediatek.com
Now the calls to enable/disable a thermal zone are centralized in a
call to a function, we can add in these the corresponding netlink
notifications.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200727231033.26512-1-daniel.lezcano@linaro.org
The TSENS integrated on MSM8939 is a v0_1 device with 10 sensors.
Different from its predecessor MSM8916, where 'calib_sel' bits sit in
separate qfprom word, MSM8939 has 'cailb' and 'calib_sel' bits mixed and
spread on discrete offsets. That's why all qfprom bits are read as one
go and later mapped to calibration data for MSM8939.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Konrad Dybcio <konradybcio@gmail.com> /* on Asus Z00T smartphone */
Acked-by: Konrad Dybcio <konradybcio@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629144926.665-3-shawn.guo@linaro.org
When a thermal zone is looked up by an ID and no zone is found matching
that ID, the thermal_zone_get_by_id() function will return a pointer to
the thermal zone list head which isn't actually a valid thermal zone.
This can lead to a subsequent crash because a valid pointer is returned
to the called, but dereferencing that pointer as struct thermal_zone is
not safe.
Fixes: 329b064fbd ("thermal: core: Get thermal zone by id")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200724170105.2705467-1-thierry.reding@gmail.com
Update PCI device id for Jasper Lake processor thermal device.
With this proc_thermal driver is getting loaded and processor
thermal functionality works on Jasper Lake system.
Fixes: f64a6583d3 ("thermal: int340x: processor_thermal: Add Jasper Lake support")
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1595577146-1221-1-git-send-email-sumeet.r.pawnikar@intel.com
This condition is reversed and will cause breakage.
Fixes: 7440f518da ("thermal/drivers/ti-soc-thermal: Avoid dereferencing ERR_PTR")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200616091949.GA11940@mwanda
The function rcar_gen3_thermal_calc_coefs() takes an argument called
'thcode' which shadows the static global 'thcode' variable. This is not
harmful but bad for readability and is harmful for planned changes to
the driver. The THCODE values should be read from hardware fuses if they
are available and only fallback to the global 'thcode' variable if they
are not fused.
Rename the global 'thcode' variable to 'thcodes' to avoid shadowing the
symbol in functions that take it as an argument.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200610003300.884258-1-niklas.soderlund+renesas@ragnatech.se
The generic netlink is initialized at subsys_initcall, so far after
the thermal init routine and the thermal generic netlink family
initialization.
On ŝome platforms, that leads to a memory corruption.
The fix was sent to netdev@ to move the genetlink framework
initialization at core_initcall.
Move the thermal core initialization to postcore level which is very
close to core level.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200717164217.18819-2-daniel.lezcano@linaro.org
The initcalls like to play joke. In our case, the thermal-netlink
initcall is called after the thermal-core initcall but this one sends
a notification before the former is initialized. No issue was spotted,
but it could lead to a memory corruption, so instead of relying on the
core_initcall for the thermal-netlink, let's initialize directly from
the thermal-core init routine, so we have full control of the init
ordering.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200717164217.18819-1-daniel.lezcano@linaro.org
The variable ret is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200706140747.489075-1-colin.king@canonical.com
When the network is not configured, the netlink is disabled on all
the system. The thermal framework assumed the netlink is always
opt-in.
Fix this by adding a Kconfig option for the netlink notification,
defaulting to yes and depending on CONFIG_NET.
As the change implies multiple stubs and in order to not pollute the
internal thermal header, the thermal_nelink.h has been added and
included in the thermal_core.h, so this one regain some kind of
clarity.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200707090159.1018-1-daniel.lezcano@linaro.org
kernel panic (Bartosz Szczepanek)
- Fix debug message level to prevent flooding on some platform (Alex
Hung)
- Fix invalid bank access by reverting "thermal: mediatek: fix
register index error" (Enric Balletbo i Serra)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl8QFhUACgkQqDIjiipP
6E99Uwf+O+MIwd4epoWG6L3SYYaOJZpkmdYJoWIXxLZu5jGiS0uf48utaXVJrTSQ
5VXCoqd2alxzAE2ZveqEV2Lp558+rT7cRmWd6ZH6UPVEC2j+1TzVfcSwJRm8jrNN
lbmt2785wcUsfRzuHqfCEIDW6HTjfcGj4d+a8CJ4K/58CdhaxOxGgDK5Wsmmy/jF
Fkco37wUVw0Ew9cAuc2OwB8hOjDMtMnBZ4xoPSaptIVEyCUurl+c1JOxFkubOM0x
a7DyBS8zKM4UVGo7jaUXwC/28TUFDZNJD8E7H4JOJfVSqK5l3HKfjqeVE44cS2SJ
u9RvLCyQkp/+CC75MfIEEpqgDLHZcA==
=0Xzx
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux into master
Pull thermal fixes from Daniel Lezcano:
- Fix invalid index array access on int340x_thermal leading to a kernel
panic (Bartosz Szczepanek)
- Fix debug message level to prevent flooding on some platform (Alex
Hung)
- Fix invalid bank access by reverting "thermal: mediatek: fix register
index error" (Enric Balletbo i Serra)
* tag 'thermal-v5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
Revert "thermal: mediatek: fix register index error"
thermal: int3403_thermal: Downgrade error message
thermal/int340x_thermal: Prevent page fault on .set_mode() op
Downgrade "Unsupported event" message from dev_err to dev_dbg to avoid
flooding with this message on some platforms.
Cc: stable@vger.kernel.org # v5.4+
Suggested-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Alex Hung <alex.hung@canonical.com>
[ rzhang: fix typo in changelog ]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200615223957.183153-1-alex.hung@canonical.com
Starting from commit "thermal/int340x_thermal: Don't require IDSP to
exist", priv->current_uuid_index is initialized to -1. This value may
be passed to int3400_thermal_run_osc() from int3400_thermal_set_mode,
contributing to page fault when accessing int3400_thermal_uuids array
at index -1.
This commit adds a check on uuid value to int3400_thermal_run_osc.
Fixes: 8d485da0dd ("thermal/int340x_thermal: Don't require IDSP to exist")
Signed-off-by: Bartosz Szczepanek <bsz@semihalf.com>
Reviewed-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
[ rzhang: Add Fixes tag ]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200708134613.131555-1-bsz@semihalf.com
The generic netlink protocol is implemented but the different
notification functions are not yet connected to the core code.
These changes add the notification calls in the different
corresponding places.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200706105538.2159-4-daniel.lezcano@linaro.org
Initially the thermal framework had a very simple notification
mechanism to send generic netlink messages to the userspace.
The notification function was never called from anywhere and the
corresponding dead code was removed. It was probably a first attempt
to introduce the netlink notification.
At LPC2018, the presentation "Linux thermal: User kernel interface",
proposed to create the notifications to the userspace via a kfifo.
The advantage of the kfifo is the performance. It is usually used from
a 1:1 communication channel where a driver captures data and sends it
as fast as possible to a userspace process.
The drawback is that only one process uses the notification channel
exclusively, thus no other process is allowed to use the channel to
get temperature or notifications.
This patch defines a generic netlink API to discover the current
thermal setup and adds event notifications as well as temperature
sampling. As any genetlink protocol, it can evolve and the versioning
allows to keep the backward compatibility.
In order to prevent the user from getting flooded with data on a
single channel, there are two multicast channels, one for the
temperature sampling when the thermal zone is updated and another one
for the events, so the user can get the events only without the
thermal zone temperature sampling.
Also, a list of commands to discover the thermal setup is added and
can be extended when needed.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200706105538.2159-3-daniel.lezcano@linaro.org
The next patch will introduce the generic netlink protocol to handle
events, sampling and command from the thermal framework. In order to
deal with the thermal zone, it uses its unique identifier to
characterize it in the message. Passing an integer is more efficient
than passing an entire string.
This change provides a function returning back a thermal zone pointer
corresponding to the identifier passed as parameter.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200706105538.2159-2-daniel.lezcano@linaro.org
The cdev, tz and governor list, as well as their respective locks are
statically defined in the thermal_core.c file.
In order to give a sane access to these list, like browsing all the
thermal zones or all the cooling devices, let's define a set of
helpers where we pass a callback as a parameter to be called for each
thermal entity.
We keep the self-encapsulation and ensure the locks are correctly
taken when looking at the list.
Acked-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200706105538.2159-1-daniel.lezcano@linaro.org
set_mode() is only called when tzd's mode is about to change. Actual
setting is performed in thermal_core, in thermal_zone_device_set_mode().
The meaning of set_mode() callback is actually to notify the driver about
the mode being changed and giving the driver a chance to oppose such
change.
To better reflect the purpose of the method rename it to change_mode()
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-12-andrzej.p@collabora.com
Setting polling_delay is now done at thermal_core level (by not polling
DISABLED devices), so no need to repeat this code.
int340x: Checking for an impossible enum value is unnecessary.
acpi/thermal: It only prints debug messages.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-11-andrzej.p@collabora.com
Polling DISABLED devices is not desired, as all such "disabled" devices
are meant to be handled by userspace. This patch introduces and uses
should_stop_polling() to decide whether the device should be polled or not.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-10-andrzej.p@collabora.com
Some thermal zone devices never change their state, so they should be
always enabled.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-9-andrzej.p@collabora.com
Use thermal_zone_device_{en|dis}able() and thermal_zone_device_is_enabled().
Consequently, all set_mode() implementations in drivers:
- can stop modifying tzd's "mode" member,
- shall stop taking tzd's lock, as it is taken in the helpers
- shall stop calling thermal_zone_device_update() as it is called in the
helpers
- can assume they are called when the mode truly changes, so checks to
verify that can be dropped
Not providing set_mode() by a driver no longer prevents the core from
being able to set tzd's mode, so the relevant check in mode_store() is
removed.
Other comments:
- acpi/thermal.c: tz->thermal_zone->mode will be updated only after we
return from set_mode(), so use function parameter in thermal_set_mode()
instead, no need to call acpi_thermal_check() in set_mode()
- thermal/imx_thermal.c: regmap writes and mode assignment are done in
thermal_zone_device_{en|dis}able() and set_mode() callback
- thermal/intel/intel_quark_dts_thermal.c: soc_dts_{en|dis}able() are a
part of set_mode() callback, so they don't need to modify tzd->mode, and
don't need to fall back to the opposite mode if unsuccessful, as the return
value will be propagated to thermal_zone_device_{en|dis}able() and
ultimately tzd's member will not be changed in thermal_zone_device_set_mode().
- thermal/of-thermal.c: no need to set zone->mode to DISABLED in
of_parse_thermal_zones() as a tzd is kzalloc'ed so mode is DISABLED anyway
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-8-andrzej.p@collabora.com
Prepare for making the drivers not access tzd's private members.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
[staticize thermal_zone_device_set_mode()]
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-7-andrzej.p@collabora.com
get_mode() is now redundant, as the state is stored in struct
thermal_zone_device.
Consequently the "mode" attribute in sysfs can always be visible, because
it is always possible to get the mode from struct tzd.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-6-andrzej.p@collabora.com
As description for DIV_ROUND_CLOSEST in file include/linux/kernel.h.
"Result is undefined for negative divisors if the dividend variable
type is unsigned and for negative dividends if the divisor variable
type is unsigned."
In current code, the FIXPT_DIV uses DIV_ROUND_CLOSEST but has not
checked sign of divisor before using. It makes undefined temperature
value in case the value is negative.
This patch fixes to satisfy DIV_ROUND_CLOSEST description
and fix bug too. Note that the variable name "reg" is not good
because it should be the same type as rcar_gen3_thermal_read().
However, it's better to rename the "reg" in a further patch as
cleanup.
Signed-off-by: Van Do <van.do.xw@renesas.com>
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
[shimoda: minor fixes, add Fixes tag]
Fixes: 564e73d283 ("thermal: rcar_gen3_thermal: Add R-Car Gen3 thermal driver")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Niklas Soderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Soderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1593085099-2057-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
The function cpu_power_to_freq is used to find a frequency and set the
cooling device to consume at most the power to be converted. For example,
if the power to be converted is 80mW, and the em table is as follow.
struct em_cap_state table[] = {
/* KHz mW */
{ 1008000, 36, 0 },
{ 1200000, 49, 0 },
{ 1296000, 59, 0 },
{ 1416000, 72, 0 },
{ 1512000, 86, 0 },
};
The target frequency should be 1416000KHz, not 1512000KHz.
Fixes: 349d39dc57 ("thermal: cpu_cooling: merge frequency and power tables")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200619090825.32747-1-finley.xiao@rock-chips.com
After merging tsens-common.c into tsens.c, we can now mark some
functions static so they don't need any prototype declarations. This
fixes the following issue reported by lkp.
>> drivers/thermal/qcom/tsens.c:385:13: warning: no previous prototype for 'tsens_critical_irq_thread' [-Wmissing-prototypes]
385 | irqreturn_t tsens_critical_irq_thread(int irq, void *data)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
>> drivers/thermal/qcom/tsens.c:455:13: warning: no previous prototype for 'tsens_irq_thread' [-Wmissing-prototypes]
455 | irqreturn_t tsens_irq_thread(int irq, void *data)
| ^~~~~~~~~~~~~~~~
>> drivers/thermal/qcom/tsens.c:523:5: warning: no previous prototype for 'tsens_set_trips' [-Wmissing-prototypes]
523 | int tsens_set_trips(void *_sensor, int low, int high)
| ^~~~~~~~~~~~~~~
>> drivers/thermal/qcom/tsens.c:560:5: warning: no previous prototype for 'tsens_enable_irq' [-Wmissing-prototypes]
560 | int tsens_enable_irq(struct tsens_priv *priv)
| ^~~~~~~~~~~~~~~~
>> drivers/thermal/qcom/tsens.c:573:6: warning: no previous prototype for 'tsens_disable_irq' [-Wmissing-prototypes]
573 | void tsens_disable_irq(struct tsens_priv *priv)
| ^~~~~~~~~~~~~~~~~
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/6757a26876b29922929abf64b1c11fa3b3033d03.1590579709.git.amit.kucheria@linaro.org
When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Fixes: 554fdbaf19 ("thermal: sprd: Add Spreadtrum thermal driver support")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1590371941-25430-1-git-send-email-yangtiezhu@loongson.cn
MT8183_NUM_ZONES should be set to 1
because MT8183 doesn't have multiple banks.
Fixes: a4ffe6b52d ("thermal: mediatek: add support for MT8183")
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200323121537.22697-6-michael.kao@mediatek.com
The new Khadas VIM2 and VIM3 boards controls the cooling fan via the
on-board microcontroller.
This implements the FAN control as thermal devices and as cell of the Khadas
MCU MFD driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Energy Model uses concept of performance domain and capacity states in
order to calculate power used by CPUs. Change naming convention from
capacity to performance state would enable wider usage in future, e.g.
upcoming support for other devices other than CPUs.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Quentin Perret <qperret@google.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Because SCHED_FIFO is a broken scheduler model (see previous patches)
take away the priority field, the kernel can't possibly make an
informed decision.
Effectively no change.
Cc: rafael.j.wysocki@intel.com
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
- Thermal framework cleanups (self-encapsulation, pointless stubs,
private structures) (Daniel Lezcano)
- Use the PM QoS frequency changes for the devfreq cooling device (Matthias
Kaehlcke)
- Remove duplicate error messages from platform_get_irq() error handling
(Markus Elfring)
- Add support for the bandgap sensors (Keerthy)
- Statically initialize .get_mode/.set_mode ops (Andrzej Pietrasiewicz)
- Add Renesas R-Car maintainer entry (Niklas Söderlund)
- Fix error checking after calling ti_bandgap_get_sensor_data() for the TI SoC
thermal (Sudip Mukherjee)
- Add latency constraint for the idle injection, the DT binding and the change
the registering function (Daniel Lezcano)
- Convert the thermal framework binding to the Yaml schema (Amit Kucheria)
- Replace zero-length array with flexible-array on i.MX 8MM (Gustavo A. R. Silva)
- Thermal framework cleanups (alphabetic order for heads, replace module.h by
export.h, make file naming consistent) (Amit Kucheria)
- Merge tsens-common into the tsens driver (Amit Kucheria)
- Fix platform dependency for the Qoriq driver (Geert Uytterhoeven)
- Clean up the rcar_thermal_update_temp() function in the rcar thermal driver
(Niklas Söderlund)
- Fix the TMSAR register for the TMUv2 on the Qoriq platform (Yuantian Tang)
- Export GDDV, OEM vendor variables, and don't require IDSP for the int340x
thermal driver - trivial conflicts fixed (Matthew Garrett)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl7jra8ACgkQqDIjiipP
6E+ugAgApBF6FsHoonWIvoSrzBrrbU2oqhEJA42Mx+iY/UnXi01I79vZ/8WpZt7M
D1J01Kf0PUhRbywoKaoCX3Oh9ZO9PKq4N9ZC8yqdoD6GLl+rC9Wmr7Ui+c80klcv
M9rYhpPYfNXTFj0saSbbFWNNhP4TvhzGsNj8foYVQDKyhjbSmNE5ipZlbmP23jlr
O53SmJAwS5zxLOd8QA5nfSWP9FYYMuCR2AHj8BUCmxiAjXZLPNB/Hz2RRBr7q0MF
zRo/4HJ04mSQYp0kluP/EBhz9g2wM/htIPyWRveB/ByKEYt3UNKjB++PJmPbu5UG
dS3aXZhRfaPqpdsWrMB9fY7ll+oyfw==
=T+RI
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Add the hwmon support on the i.MX SC (Anson Huang)
- Thermal framework cleanups (self-encapsulation, pointless stubs,
private structures) (Daniel Lezcano)
- Use the PM QoS frequency changes for the devfreq cooling device
(Matthias Kaehlcke)
- Remove duplicate error messages from platform_get_irq() error
handling (Markus Elfring)
- Add support for the bandgap sensors (Keerthy)
- Statically initialize .get_mode/.set_mode ops (Andrzej Pietrasiewicz)
- Add Renesas R-Car maintainer entry (Niklas Söderlund)
- Fix error checking after calling ti_bandgap_get_sensor_data() for the
TI SoC thermal (Sudip Mukherjee)
- Add latency constraint for the idle injection, the DT binding and the
change the registering function (Daniel Lezcano)
- Convert the thermal framework binding to the Yaml schema (Amit
Kucheria)
- Replace zero-length array with flexible-array on i.MX 8MM (Gustavo A.
R. Silva)
- Thermal framework cleanups (alphabetic order for heads, replace
module.h by export.h, make file naming consistent) (Amit Kucheria)
- Merge tsens-common into the tsens driver (Amit Kucheria)
- Fix platform dependency for the Qoriq driver (Geert Uytterhoeven)
- Clean up the rcar_thermal_update_temp() function in the rcar thermal
driver (Niklas Söderlund)
- Fix the TMSAR register for the TMUv2 on the Qoriq platform (Yuantian
Tang)
- Export GDDV, OEM vendor variables, and don't require IDSP for the
int340x thermal driver - trivial conflicts fixed (Matthew Garrett)
* tag 'thermal-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (48 commits)
thermal/int340x_thermal: Don't require IDSP to exist
thermal/int340x_thermal: Export OEM vendor variables
thermal/int340x_thermal: Export GDDV
thermal: qoriq: Update the settings for TMUv2
thermal: rcar_thermal: Clean up rcar_thermal_update_temp()
thermal: qoriq: Add platform dependencies
drivers: thermal: tsens: Merge tsens-common.c into tsens.c
thermal/of: Rename of-thermal.c
thermal/governors: Prefix all source files with gov_
thermal/drivers/user_space: Sort headers alphabetically
thermal/drivers/of-thermal: Sort headers alphabetically
thermal/drivers/cpufreq_cooling: Replace module.h with export.h
thermal/drivers/cpufreq_cooling: Sort headers alphabetically
thermal/drivers/clock_cooling: Include export.h
thermal/drivers/clock_cooling: Sort headers alphabetically
thermal/drivers/thermal_hwmon: Include export.h
thermal/drivers/thermal_hwmon: Sort headers alphabetically
thermal/drivers/thermal_helpers: Include export.h
thermal/drivers/thermal_helpers: Sort headers alphabetically
thermal/core: Replace module.h with export.h
...
The IDSP method doesn't appear to exist on the most recent Intel platforms:
instead, the IDSP data is included in the GDDV blob. Since we probably
don't want to decompress and parse that in-kernel, just allow any UUID to
be written if IDSP is missing.
Signed-off-by: Matthew Garrett <mjg59@google.com>
Tested-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
[ rzhang: fix checkpatch warning in changelog ]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200414020953.255364-3-matthewgarrett@google.com
The platform vendor may expose an array of OEM-specific values to be used
in determining DPTF policy. These are obtained via the ODVP method, and
then simply exposed in sysfs. In addition, they are updated when a
notification is received or when the DPTF policy is changed by userland.
Conflicts:
drivers/thermal/intel/int340x_thermal/int3400_thermal.c
Signed-off-by: Matthew Garrett <mjg59@google.com>
Tested-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200414020953.255364-2-matthewgarrett@google.com
Implementing DPTF properly requires making use of firmware-provided
information associated with the INT3400 device. Calling GDDV provides a
buffer of information which userland can then interpret to determine
appropriate DPTF policy.
Conflicts:
drivers/thermal/intel/int340x_thermal/int3400_thermal.c
Signed-off-by: Matthew Garrett <mjg59@google.com>
Tested-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200414020953.255364-1-matthewgarrett@google.com
For TMU v2, TMSAR registers need to be set properly to get the
accurate temperature values.
Also the temperature read needs to be converted to degree Celsius
since it is in degrees Kelvin.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200526060212.4118-1-andy.tang@nxp.com
Moving the ctemp variable out of the private data structure made it
possible to clean up rcar_thermal_update_temp(). Initialize the local
ctemp to the error code to return if the reading fails and just return
it at the end of the function.
It's OK to change the datatype of old, new and ctemp to int as all
values are ANDed with CTEMP (0x3f) before being stored. While at it
change the datatype of the loop variable 'i' to to unsigned int.
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200514152505.1927634-1-niklas.soderlund+renesas@ragnatech.se
The QorIQ Thermal Monitoring Unit is only present on Freescale E500MC
and Layerscape SoCs, and on NXP i.MX8 SoCs. Add platform dependencies
to the QORIQ_THERMAL config symbol, to avoid asking the user about it
when configuring a kernel without support for any of the aforementioned
SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200507112955.23520-5-geert+renesas@glider.be
tsens-common.c has outlived its usefuless. It was created expecting lots
of custom routines per version of the TSENS IP. We haven't needed those,
there is now only data in the version-specific files.
Merge the code for tsens-common.c into tsens.c. As a result,
- Remove any unnecessary forward declarations in tsens.h.
- Add a Linaro copyright to tsens.c.
- Fixup the Makefile to remove tsens-common.c.
- Where it made sense, fix some 80-column alignments in the
tsens-common.c code being copied over.
There is no functional change with this patch.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/e30e2ba6fa5c007983afd4d7d4e0311c0b57917a.1588183879.git.amit.kucheria@linaro.org
The thermal framework can no longer be compiled as a module as of
commit 554b3529fe ("thermal/drivers/core: Remove the module Kconfig's
option"). Remove the MODULE_* tags.
Rui is mentioned in the copyright line at the top of the file and the
license is mentioned in the SPDX tags. So no loss of information.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/74339a09a55f8f3d86c4074fc2bf853a302d6186.1589199124.git.amit.kucheria@linaro.org
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200507192517.GA16557@embeddedor
Today, there is no user for the cpuidle cooling device. The targetted
platform is ARM and ARM64.
The cpuidle and the cpufreq cooling device are based on the device tree.
As the cpuidle cooling device can have its own configuration depending
on the platform and the available idle states. The DT node description
will give the optional properties to set the cooling device up.
Do no longer rely on the CPU node which is prone to error and will
lead to a confusion in the DT because the cpufreq cooling device is
also using it. Let initialize the cpuidle cooling device with the DT
binding.
This was tested on:
- hikey960
- hikey6220
- rock960
- db845c
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200429103644.5492-3-daniel.lezcano@linaro.org
i.MX8 SoCs DTS file needs system control macro definitions, so move them
into dt-binding headfile, then include/linux/firmware/imx/types.h can be
removed and those drivers using it should be changed accordingly.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On error the function ti_bandgap_get_sensor_data() returns the error
code in ERR_PTR() but we only checked if the return value is NULL or
not. And, so we can dereference an error code inside ERR_PTR.
While at it, convert a check to IS_ERR_OR_NULL.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200424161944.6044-1-sudipm.mukherjee@gmail.com
int3400_thermal_ops is used inside int3400_thermal_probe() only after
the assignments, which can just as well be made statically at struct's
initizer.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200414180105.20042-2-andrzej.p@collabora.com
Add VTM thermal support. In the Voltage Thermal Management
Module(VTM), K3 AM654 supplies a voltage reference and a temperature
sensor feature that are gathered in the band gap voltage and
temperature sensor (VBGAPTS) module. The band gap provides current and
voltage reference for its internal circuits and other analog IP
blocks. The analog-to-digital converter (ADC) produces an output value
that is proportional to the silicon temperature.
Currently reading temperatures only is supported. There are no
active/passive cooling agent supported.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200407055116.16082-3-j-keerthy@ti.com
The function “platform_get_irq” can log an error already.
Thus omit redundant messages for the exception handling in the
calling functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/05f49ae7-5cc7-d6a0-fc3d-abaf2a0b373c@web.de
The function is not used any place other than the thermal
directory. It does not make sense to export its definition in the
global header as there is no use of it.
Move the definition to the internal header and allow better
self-encapsulation.
Take the opportunity to add the parameter names to make checkpatch
happy and remove the pointless stubs.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200402142747.8307-6-daniel.lezcano@linaro.org
The function is not used any place other than the thermal
directory. It does not make sense to export its definition in the
global header as there is no use of it.
Move the definition to the internal header and allow better
self-encapsulation.
Take the opportunity to add the parameter names to make checkpatch
happy and remove the pointless stubs.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200402142747.8307-5-daniel.lezcano@linaro.org
The struct thermal_trip is only used by the thermal internals, it is
pointless to export the definition in the global header.
Move the structure to the thermal_core.h internal header.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200402142747.8307-4-daniel.lezcano@linaro.org
The exported IPA functions are used by the IPA. It is pointless to
declare the functions in the thermal.h file.
For better self-encapsulation and less impact for the compilation if a
change is made on it. Move the code in the thermal core internal
header file.
As the users depends on THERMAL then it is pointless to have the stub,
remove them.
Take also the opportunity to fix checkpatch warnings/errors when
moving the code around.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200402142747.8307-3-daniel.lezcano@linaro.org
The structure belongs to the thermal core internals but it is exported
in the include/linux/thermal.h
For better self-encapsulation and less impact for the compilation if a
change is made on it. Move the structure in the thermal core internal
header file.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200402142747.8307-2-daniel.lezcano@linaro.org
The default governor set at compilation time is a thermal internal
business, no need to export to the global thermal header.
Move the config options to the internal header.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200402142747.8307-1-daniel.lezcano@linaro.org
Now that devfreq supports limiting the frequency range of a device
through PM QoS make use of it instead of disabling OPPs that should
not be used.
The switch from disabling OPPs to PM QoS introduces a subtle behavioral
change in case of conflicting requests (min > max): PM QoS gives
precedence to the MIN_FREQUENCY request, while higher OPPs disabled
with dev_pm_opp_disable() would override MIN_FREQUENCY.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200318114548.19916-4-lukasz.luba@arm.com
The last temperature and the current temperature are show via a
dev_debug. The line before, those temperature are also traced.
It is pointless to duplicate the traces for the temperatures,
remove the dev_dbg traces.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200331165449.30355-2-daniel.lezcano@linaro.org
The function thermal_zone_set_trips() is used by the thermal core code
in order to update the next trip points, there are no other users.
Move the function definition in the thermal_core.h, remove the
EXPORT_SYMBOL_GPL and document the function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200331165449.30355-1-daniel.lezcano@linaro.org
- Add interrupt support on the rcar sensor (Niklas Söderlund)
- Add a new Spreadtrum thermal driver (Baolin Wang)
- Add thermal binding for the fsl scu board, a new API to retrieve the
sensor id bound to the thermal zone and i.MX system controller
sensor (Anson Huang))
- Remove warning log when a deferred probe is requested on Exynos
(Marek Szyprowski)
- Add the thermal monitoring unit support for imx8mm with its DT
bindings (Anson Huang)
- Rephrase the Kconfig text for clarity (Linus Walleij)
- Use the gpio descriptor for the ti-soc-thermal (Linus Walleij)
- Align msg structure to 4 bytes for i.MX SC, fix the Kconfig
dependency, add the __may_be unused annotation for PM functions and
the COMPILE_TEST option for imx8mm (Anson Huang)
- Fix a dependency on regmap in Kconfig for qoriq (Yuantian Tang)
- Add DT binding and support for the rcar gen3 r8a77961 and improve
the error path on the rcar init function (Niklas Söderlund)
- Cleanup and improvements for the tsens Qcom sensor (Amit Kucheria)
- Improve code by removing lock and caching values in the rcar thermal
sensor (Niklas Söderlund)
- Cleanup in the qoriq drivers and add a call to
imx_thermal_unregister_legacy_cooling in the removal function (Anson
Huang)
- Remove redundant 'maxItems' in tsens and sprd DT bindings (Rob Herring)
- Change the thermal DT bindings by making the cooling-maps optional
(Yuantian Tang)
- Add Tiger Lake support (Sumeet Pawnikar)
- Use scnprintf() for avoiding potential buffer overflow (Takashi Iwai)
- Make pkg_temp_lock a raw_spinlock_t(Clark Williams)
- Fix incorrect data types by changing them to signed on i.MX SC (Anson Huang)
- Replace zero-length array with flexible-array member (Gustavo A. R. Silva)
- Add support for i.MX8MP in the driver and in the DT bindings (Anson Huang)
- Fix return value of the cpufreq_set_cur_state() function (Willy Wolff)
- Remove abusing and scary WARN_ON in the cpufreq cooling device
(Daniel Lezcano)
- Fix build warning of incorrect argument type reported by sparse on
imx8mm (Anson Huang)
- Fix stub for the devfreq cooling device (Martin Blumenstingl)
- Fix cpu idle cooling documentation (Sergey Vidishev)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl6MXkEACgkQqDIjiipP
6E+BIggAh52YBU8D8GthsvCPTgka95+wAIaZtx4Y7UnhvshHhM2w+m97TQOXK373
95mwO9mwQuAoksSmLo7pBQYJ7HItQ26Yoq9akpOL6EiT+BEWiqoHJgl+afVVtoKa
n67d3Pa6coup1+PQNIA8kpTIOmUQTP8THtwpZ3HlChWsg22NTd0QUGpGJ1TtBD/q
KqMdQjxahFJ4RTYsnECWBkw3EMkczMNMgdrXEvm4rMkcaJzv9g2ZPqerOShK/RzP
8sejWczt6jaRwu4hLpd/lLikTSHZoXMFJ8ylAiQXFELCPAQIrMS/ae+dTGJ4qP7x
hkjsewPbeA1Z+al/IBVHiCtOzKkICQ==
=XDYl
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Convert tsens configuration DT binding to yaml (Rajeshwari)
- Add interrupt support on the rcar sensor (Niklas Söderlund)
- Add a new Spreadtrum thermal driver (Baolin Wang)
- Add thermal binding for the fsl scu board, a new API to retrieve the
sensor id bound to the thermal zone and i.MX system controller sensor
(Anson Huang))
- Remove warning log when a deferred probe is requested on Exynos
(Marek Szyprowski)
- Add the thermal monitoring unit support for imx8mm with its DT
bindings (Anson Huang)
- Rephrase the Kconfig text for clarity (Linus Walleij)
- Use the gpio descriptor for the ti-soc-thermal (Linus Walleij)
- Align msg structure to 4 bytes for i.MX SC, fix the Kconfig
dependency, add the __may_be unused annotation for PM functions and
the COMPILE_TEST option for imx8mm (Anson Huang)
- Fix a dependency on regmap in Kconfig for qoriq (Yuantian Tang)
- Add DT binding and support for the rcar gen3 r8a77961 and improve the
error path on the rcar init function (Niklas Söderlund)
- Cleanup and improvements for the tsens Qcom sensor (Amit Kucheria)
- Improve code by removing lock and caching values in the rcar thermal
sensor (Niklas Söderlund)
- Cleanup in the qoriq drivers and add a call to
imx_thermal_unregister_legacy_cooling in the removal function (Anson
Huang)
- Remove redundant 'maxItems' in tsens and sprd DT bindings (Rob
Herring)
- Change the thermal DT bindings by making the cooling-maps optional
(Yuantian Tang)
- Add Tiger Lake support (Sumeet Pawnikar)
- Use scnprintf() for avoiding potential buffer overflow (Takashi Iwai)
- Make pkg_temp_lock a raw_spinlock_t(Clark Williams)
- Fix incorrect data types by changing them to signed on i.MX SC (Anson
Huang)
- Replace zero-length array with flexible-array member (Gustavo A. R.
Silva)
- Add support for i.MX8MP in the driver and in the DT bindings (Anson
Huang)
- Fix return value of the cpufreq_set_cur_state() function (Willy
Wolff)
- Remove abusing and scary WARN_ON in the cpufreq cooling device
(Daniel Lezcano)
- Fix build warning of incorrect argument type reported by sparse on
imx8mm (Anson Huang)
- Fix stub for the devfreq cooling device (Martin Blumenstingl)
- Fix cpu idle cooling documentation (Sergey Vidishev)
* tag 'thermal-v5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (52 commits)
Documentation: cpu-idle-cooling: Fix diagram for 33% duty cycle
thermal: devfreq_cooling: inline all stubs for CONFIG_DEVFREQ_THERMAL=n
thermal: imx8mm: Fix build warning of incorrect argument type
thermal/drivers/cpufreq_cooling: Remove abusing WARN_ON
thermal/drivers/cpufreq_cooling: Fix return of cpufreq_set_cur_state
thermal: imx8mm: Add i.MX8MP support
dt-bindings: thermal: imx8mm-thermal: Add support for i.MX8MP
thermal: qcom: tsens.h: Replace zero-length array with flexible-array member
thermal: imx_sc_thermal: Fix incorrect data type
thermal: int340x_thermal: Use scnprintf() for avoiding potential buffer overflow
thermal: int340x: processor_thermal: Add Tiger Lake support
thermal/x86_pkg_temp: Make pkg_temp_lock a raw_spinlock_t
dt-bindings: thermal: make cooling-maps property optional
dt-bindings: thermal: qcom-tsens: Remove redundant 'maxItems'
dt-bindings: thermal: sprd: Remove redundant 'maxItems'
thermal: imx: Calling imx_thermal_unregister_legacy_cooling() in .remove
thermal: qoriq: Sort includes alphabetically
thermal: qoriq: Use devm_add_action_or_reset() to handle all cleanups
thermal: rcar_thermal: Remove lock in rcar_thermal_get_current_temp()
thermal: rcar_thermal: Do not store ctemp in rcar_thermal_priv
...
- Update the ACPICA code in the kernel to upstream revision 20200326
including:
* Fix for a typo in a comment field (Bob Moore).
* acpiExec namespace init file fixes (Bob Moore).
* Addition of NHLT to the known tables list (Cezary Rojewski).
* Conversion of PlatformCommChannel ASL keyword to PCC (Erik
Kaneda).
* acpiexec cleanup (Erik Kaneda).
* WSMT-related typo fix (Erik Kaneda).
* sprintf() utility function fix (John Levon).
* IVRS IVHD type 11h parsing implementation (Michał Żygowski).
* IVRS IVHD type 10h reserved field name fix (Michał Żygowski).
- Fix ACPI-related CPU hotplug deadlock on x86 (Qian Cai).
- Fix Intel Tiger Lake ACPI device IDs in several places (Gayatri
Kammela).
- Add ACPI backlight blacklist entry for Acer Aspire 5783z (Hans
de Goede).
- Fix documentation of the "acpi_backlight" kernel command line
switch (Randy Dunlap).
- Clean up the acpi_get_psd_map() CPPC library routine (Liguang
Zhang).
-----BEGIN PGP SIGNATURE-----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=b3Dp
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Additional ACPI updates.
These update the ACPICA code in the kernel to the 20200326 upstream
revision, fix an ACPI-related CPU hotplug deadlock on x86, update
Intel Tiger Lake device IDs in some places, add a new ACPI backlight
blacklist entry, update the "acpi_backlight" kernel command line
switch documentation and clean up a CPPC library routine.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20200326
including:
* Fix for a typo in a comment field (Bob Moore)
* acpiExec namespace init file fixes (Bob Moore)
* Addition of NHLT to the known tables list (Cezary Rojewski)
* Conversion of PlatformCommChannel ASL keyword to PCC (Erik
Kaneda)
* acpiexec cleanup (Erik Kaneda)
* WSMT-related typo fix (Erik Kaneda)
* sprintf() utility function fix (John Levon)
* IVRS IVHD type 11h parsing implementation (Michał Żygowski)
* IVRS IVHD type 10h reserved field name fix (Michał Żygowski)
- Fix ACPI-related CPU hotplug deadlock on x86 (Qian Cai)
- Fix Intel Tiger Lake ACPI device IDs in several places (Gayatri
Kammela)
- Add ACPI backlight blacklist entry for Acer Aspire 5783z (Hans de
Goede)
- Fix documentation of the "acpi_backlight" kernel command line
switch (Randy Dunlap)
- Clean up the acpi_get_psd_map() CPPC library routine (Liguang
Zhang)"
* tag 'acpi-5.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
x86: ACPI: fix CPU hotplug deadlock
thermal: int340x_thermal: fix: Update Tiger Lake ACPI device IDs
platform/x86: intel-hid: fix: Update Tiger Lake ACPI device ID
ACPI: Update Tiger Lake ACPI device IDs
ACPI: video: Use native backlight on Acer Aspire 5783z
ACPI: video: Docs update for "acpi_backlight" kernel parameter options
ACPICA: Update version 20200326
ACPICA: Fixes for acpiExec namespace init file
ACPICA: Add NHLT table signature
ACPICA: WSMT: Fix typo, no functional change
ACPICA: utilities: fix sprintf()
ACPICA: acpiexec: remove redeclaration of acpi_gbl_db_opt_no_region_support
ACPICA: Change PlatformCommChannel ASL keyword to PCC
ACPICA: Fix IVRS IVHD type 10h reserved field name
ACPICA: Implement IVRS IVHD type 11h parsing
ACPICA: Fix a typo in a comment field
ACPI: CPPC: clean up acpi_get_psd_map()
Tiger Lake's new unique ACPI device IDs for Intel thermal driver are not
valid because of missing 'C' in the IDs. Fix the IDs by updating them.
After the update, the new IDs should now look like
INT1040 --> INTC1040
INT1043 --> INTC1043
Fixes: 9b1b5535df ("thermal: int340x_thermal: Add Tiger Lake ACPI device IDs")
Cc: 5.6+ <stable@vger.kernel.org> # 5.6+
Suggested-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle are:
- Various NUMA scheduling updates: harmonize the load-balancer and
NUMA placement logic to not work against each other. The intended
result is better locality, better utilization and fewer migrations.
- Introduce Thermal Pressure tracking and optimizations, to improve
task placement on thermally overloaded systems.
- Implement frequency invariant scheduler accounting on (some) x86
CPUs. This is done by observing and sampling the 'recent' CPU
frequency average at ~tick boundaries. The CPU provides this data
via the APERF/MPERF MSRs. This hopefully makes our capacity
estimates more precise and keeps tasks on the same CPU better even
if it might seem overloaded at a lower momentary frequency. (As
usual, turbo mode is a complication that we resolve by observing
the maximum frequency and renormalizing to it.)
- Add asymmetric CPU capacity wakeup scan to improve capacity
utilization on asymmetric topologies. (big.LITTLE systems)
- PSI fixes and optimizations.
- RT scheduling capacity awareness fixes & improvements.
- Optimize the CONFIG_RT_GROUP_SCHED constraints code.
- Misc fixes, cleanups and optimizations - see the changelog for
details"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (62 commits)
threads: Update PID limit comment according to futex UAPI change
sched/fair: Fix condition of avg_load calculation
sched/rt: cpupri_find: Trigger a full search as fallback
kthread: Do not preempt current task if it is going to call schedule()
sched/fair: Improve spreading of utilization
sched: Avoid scale real weight down to zero
psi: Move PF_MEMSTALL out of task->flags
MAINTAINERS: Add maintenance information for psi
psi: Optimize switching tasks inside shared cgroups
psi: Fix cpu.pressure for cpu.max and competing cgroups
sched/core: Distribute tasks within affinity masks
sched/fair: Fix enqueue_task_fair warning
thermal/cpu-cooling, sched/core: Move the arch_set_thermal_pressure() API to generic scheduler code
sched/rt: Remove unnecessary push for unfit tasks
sched/rt: Allow pulling unfitting task
sched/rt: Optimize cpupri_find() on non-heterogenous systems
sched/rt: Re-instate old behavior in select_task_rq_rt()
sched/rt: cpupri_find: Implement fallback mechanism for !fit case
sched/fair: Fix reordering of enqueue/dequeue_task_fair()
sched/fair: Fix runnable_avg for throttled cfs
...
Pull perf updates from Ingo Molnar:
"The main changes in this cycle were:
Kernel side changes:
- A couple of x86/cpu cleanups and changes were grandfathered in due
to patch dependencies. These clean up the set of CPU model/family
matching macros with a consistent namespace and C99 initializer
style.
- A bunch of updates to various low level PMU drivers:
* AMD Family 19h L3 uncore PMU
* Intel Tiger Lake uncore support
* misc fixes to LBR TOS sampling
- optprobe fixes
- perf/cgroup: optimize cgroup event sched-in processing
- misc cleanups and fixes
Tooling side changes are to:
- perf {annotate,expr,record,report,stat,test}
- perl scripting
- libapi, libperf and libtraceevent
- vendor events on Intel and S390, ARM cs-etm
- Intel PT updates
- Documentation changes and updates to core facilities
- misc cleanups, fixes and other enhancements"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (89 commits)
cpufreq/intel_pstate: Fix wrong macro conversion
x86/cpu: Cleanup the now unused CPU match macros
hwrng: via_rng: Convert to new X86 CPU match macros
crypto: Convert to new CPU match macros
ASoC: Intel: Convert to new X86 CPU match macros
powercap/intel_rapl: Convert to new X86 CPU match macros
PCI: intel-mid: Convert to new X86 CPU match macros
mmc: sdhci-acpi: Convert to new X86 CPU match macros
intel_idle: Convert to new X86 CPU match macros
extcon: axp288: Convert to new X86 CPU match macros
thermal: Convert to new X86 CPU match macros
hwmon: Convert to new X86 CPU match macros
platform/x86: Convert to new CPU match macros
EDAC: Convert to new X86 CPU match macros
cpufreq: Convert to new X86 CPU match macros
ACPI: Convert to new X86 CPU match macros
x86/platform: Convert to new CPU match macros
x86/kernel: Convert to new CPU match macros
x86/kvm: Convert to new CPU match macros
x86/perf/events: Convert to new CPU match macros
...
The pkg_temp_lock spinlock is acquired in the thermal vector handler which
is truly atomic context even on PREEMPT_RT kernels.
The critical sections are tiny, so change it to a raw spinlock.
Signed-off-by: Clark Williams <williams@redhat.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20191008110021.2j44ayunal7fkb7i@linutronix.de
The new macro set has a consistent namespace and uses C99 initializers
instead of the grufty C89 ones.
Get rid the of the local QUARK defines and use the proper ones.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lkml.kernel.org/r/20200320131509.967017771@linutronix.de
The WARN_ON macros are used at the entry functions state2power() and
set_cur_state().
state2power() is called with the max_state retrieved from
get_max_state which returns cpufreq_cdev->max_level, then it check if
max_state is > cpufreq_cdev->max_level. The test does not really makes
sense but let's assume we want to make sure to catch an error if the
code evolves. However the WARN_ON is overkill.
set_cur_state() is also called from userspace if we write to the
sysfs. It is easy to see a stack dumped by just writing to sysfs
/sys/class/thermal/cooling_device0/cur_state a value greater than
"max_level". A bit scary. Returing -EINVAL is enough.
Remove these WARN_ON.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20200321193107.21590-1-daniel.lezcano@linaro.org
When setting the cooling device current state from userspace via sysfs,
the operation fails by returning an -EINVAL.
It appears the recent changes with the per-policy frequency QoS
introduced a regression as reported by:
https://lkml.org/lkml/2020/3/20/599
The function freq_qos_update_request returns 0 or 1 describing update
effectiveness, and a negative error code on failure. However,
cpufreq_set_cur_state returns 0 on success or an error code otherwise.
Consider the QoS update as successful if the function does not return
an error.
Fixes: 3000ce3c52 ("cpufreq: Use per-policy frequency QoS")
Signed-off-by: Willy Wolff <willy.mh.wolff.ml@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200321092740.7vvwfxsebcrznydh@macmini.local
i.MX8MP shares same TMU with i.MX8MM, the only difference is i.MX8MP
has two thermal sensors while i.MX8MM ONLY has one, add multiple sensors
support for i.MX8MM TMU driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1584674791-9717-2-git-send-email-Anson.Huang@nxp.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200319184838.GA25767@embeddedor.com
The temperature value passed from SCU could be negative value,
the data type should be signed instead of unsigned.
Fixes: e20db70dba ("thermal: imx_sc: add i.MX system controller thermal support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1584606380-9972-1-git-send-email-Anson.Huang@nxp.com
Yang Yingliang
Srinivas Pandruvada
Chunyan Zhang
Finley Xiao
Linus Torvalds
Borislav Petkov
Yang Li
Colin Ian King
Lukasz Luba
Ansuel Smith
Thara Gopinath
Lin Ruizhe
Zhen Lei
dingsenjie
Ye Bin
Zhang Rui
Ruiqi Gong
Konrad Dybcio
Guangqing Zhu
David Collins
brian-sy yang
Hao Fang
Daniel Lezcano
Manaf Meethalavalappu Pallikunhi
jeson.gao
Jia-Ju Bai
Zhang Yunkai
Niklas Söderlund
Bhaskar Chowdhury
Tang Bin
Viresh Kumar
Dmitry Baryshkov
Tony Lindgren
Arnd Bergmann
Kai-Heng Feng
Zheng Yongjun
Sumeet Pawnikar
Fabio Estevam
Rikard Falkeborn
Randy Dunlap
Martin Blumenstingl
Andres Freund
Peter Ujfalusi
Zhuguangqing
Bernard Zhao
Yangtao Li
Fabien Parent
Tian Tao
Michael Kao
Joe Perches
Jing Xiangfeng
Adam Ford
Qinglang Miao
Lad Prabhakar
Geert Uytterhoeven
Anson Huang
Jakub Kicinski
Dmitry Osipenko
Veera Vegivada
Gustavo A. R. Silva
Rafael J. Wysocki
Henry Yen
Shawn Guo
Thierry Reding
Dan Carpenter
Marian-Cristian Rotariu
Amit Kucheria
Enric Balletbo i Serra
Alex Hung
Bartosz Szczepanek
Andrzej Pietrasiewicz
Dien Pham
Tiezhu Yang
Neil Armstrong
Peter Zijlstra
Matthew Garrett
Yuantian Tang
Dong Aisheng
Sudip Mukherjee
Keerthy
Markus Elfring
Matthias Kaehlcke
Gayatri Kammela
Clark Williams
Thomas Gleixner
Willy Wolff
Gustavo A. R. Silva