Just some minor noise follow-up to address some stylistic issues of
commit 3b3ae88026 ("net: sched: consolidate tc_classify{,_compat}").
Accidentally v1 instead of v2 of that commit got applied, so this
patch adds the relative diff.
Suggested-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the driver would refuse to load if it couldn't secure
enough VIs from the MC to fulfill its RSS requirements.
This was causing probe to fail on later functions in
configurations where we'd run out of VIs, such as having many
VFs.
This change allows the driver to load with fewer VIs, down to a
minimum of 2. A warning will be printed saying that RSS
requirements were not met, possibly affecting performance.
efx->max_tx_channels needs to be set to avoid going down the
failure path in efx_probe_nic() immediately in the loop after the
probe() NIC-type function.
Also, Set rc=ENOSPC when bombing out of efx_probe_nic due to lack
of VIs.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forcing uninitialized state allows us to upgrade and reinitialize
the adapter.
FW_VERSION_T4 = 1.4.0.0
FW_VERSION_T5 = 0.0.0.0
FW_VERSION_T6 = 0.0.0.0
At this point driver supports above and greater than above version.
If FW in adapter < min FW_VERSION driver supports tries to upgrade the FW
If FW in adapter >= FW_VERSION driver supports then it follows normal path
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- code beautification
- remove obsolete 'deleted' attribute for bat-gw node
- increase internal version number
- prevent potential access to netdev object after deregistration
- set needed_head/tail_room for batman virtual interface
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=KKXM
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
Included changes:
- code beautification
- remove obsolete 'deleted' attribute for bat-gw node
- increase internal version number
- prevent potential access to netdev object after deregistration
- set needed_head/tail_room for batman virtual interface
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typo in conntrack.c
s/CONFIG_NF_CONNTRACK_LABEL/CONFIG_NF_CONNTRACK_LABELS/
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net: Refactor inetpeer cache and add support for VRFs
Per Dave's comment on the version 1 patch adding VRF support to inetpeer
cache by explicitly making the address + index a key. Refactored the
inetpeer code in the process; mostly impacts the use by tcp_metrics.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
inetpeer caches based on address only, so duplicate IP addresses within
a namespace return the same cached entry. Enhance the ipv4 address key
to contain both the IPv4 address and VRF device index.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the inetpeer_addr_base union to inetpeer_addr and drop
inetpeer_addr_base.
Both the a6 and in6_addr overlays are not needed; drop the __be32 version
and rename in6 to a6 for consistency with ipv4. Add a new u32 array to
the union which removes the need for the typecast in the compare function
and the use of a consistent arg for both ipv4 and ipv6 addresses which
makes the compare function more readable.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_metrics and inetpeer both have functions to compare inetpeer
addresses. Consolidate into 1 version.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use inetpeer set,get helpers in tcp_metrics rather than peeking into
the inetpeer_addr struct.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactors a common line into helper function.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to use a custom dst broke tcpdump captures on the VRF device:
$ tcpdump -n -i vrf10
...
05:32:29.009362 IP 10.2.1.254 > 10.2.1.2: ICMP echo request, id 21989, seq 1, length 64
05:32:29.009855 00:00:40:01:8d:36 > 45:00:00:54:d6:6f, ethertype Unknown (0x0a02), length 84:
0x0000: 0102 0a02 01fe 0000 9181 55e5 0001 bd11 ..........U.....
0x0010: da55 0000 0000 bb5d 0700 0000 0000 1011 .U.....]........
0x0020: 1213 1415 1617 1819 1a1b 1c1d 1e1f 2021 ...............!
0x0030: 2223 2425 2627 2829 2a2b 2c2d 2e2f 3031 "#$%&'()*+,-./01
0x0040: 3233 3435 3637 234567
Local packets going through the VRF device are missing an ethernet header.
Fix by adding one and then stripping it off before pushing back to the IP
stack. With this patch you get the expected dumps:
...
05:36:15.713944 IP 10.2.1.254 > 10.2.1.2: ICMP echo request, id 23795, seq 1, length 64
05:36:15.714160 IP 10.2.1.2 > 10.2.1.254: ICMP echo reply, id 23795, seq 1, length 64
...
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The range of addresses between 224.0.0.0 and 224.0.0.255 inclusive, is
reserved for the use of routing protocols and other low-level topology
discovery or maintenance protocols, such as gateway discovery and
group membership reporting. Multicast routers should not forward any
multicast datagram with destination addresses in this range,
regardless of its TTL.
Currently, IGMP reports are generated for this reserved range of
addresses even though a router will ignore this information since it
has no purpose. However, the presence of reserved group addresses in
an IGMP membership report uses up network bandwidth and can also
obscure addresses of interest when inspecting membership reports using
packet inspection or debug messages.
Although the RFCs for the various version of IGMP (e.g.RFC 3376 for
v3) do not specify that the reserved addresses be excluded from
membership reports, it should do no harm in doing so. In particular
there should be no adverse effect in any IGMP snooping functionality
since 224.0.0.x is specifically excluded as per RFC 4541 (IGMP and MLD
Snooping Switches Considerations) section 2.1.2. Data Forwarding
Rules:
2) Packets with a destination IP (DIP) address in the 224.0.0.X
range which are not IGMP must be forwarded on all ports.
IGMP reports for local multicast groups can now be optionally
inhibited by means of a system control variable (by setting the value
to zero) e.g.:
echo 0 > /proc/sys/net/ipv4/igmp_link_local_mcast_reports
To retain backwards compatibility the previous behaviour is retained
by default on system boot or reverted by setting the value back to
non-zero e.g.:
echo 1 > /proc/sys/net/ipv4/igmp_link_local_mcast_reports
Signed-off-by: Philip Downey <pdowney@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The multicast hardware counter on 8168/8111 chips is only 32 bit while the
statistics in struct rtnl_link_stats64 are 64 bit. Given that statistics
are requested on an irregular basis, an overflow of the hardware counter
can go unnoticed. To count even very large numbers of multicast packets
reliably, add a software counter and remove previously applied code to
fill the multicast field requested by @rtl8169_get_stats64 with the values
read from the rx_multicast hardware counter.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix MSI/MSI-X on pseries from Guilherme
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qDdb
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fix MSI/MSI-X on pseries from Guilherme"
* tag 'powerpc-4.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/PCI: Disable MSI/MSI-X interrupts at PCI probe time in OF case
PCI: Make pci_msi_setup_pci_dev() non-static for use by arch code
Pull networking fixes from David Miller:
"Some straggler bug fixes here:
1) Netlink_sendmsg() doesn't check iterator type properly in mmap
case, from Ken-ichirou MATSUZAWA.
2) Don't sleep in atomic context in bcmgenet driver, from Florian
Fainelli.
3) The pfkey_broadcast() code patch can't actually ever use anything
other than GFP_ATOMIC. And the cases that right now pass
GFP_KERNEL or similar will currently trigger an RCU splat. Just
use GFP_ATOMIC unconditionally. From David Ahern.
4) Fix FD bit timings handling in pcan_usb driver, from Marc
Kleine-Budde.
5) Cache dst leaked in ip6_gre tunnel removal, fix from Huaibin Wang.
6) Traversal into drivers/net/ethernet/renesas should be triggered by
CONFIG_NET_VENDOR_RENESAS, not a particular driver's config
option. From Kazuya Mizuguchi.
7) Fix regression in handling of igmp_join errors in vxlan, from
Marcelo Ricardo Leitner.
8) Make phy_{read,write}_mmd_indirect() properly take the mdio_lock
mutex when programming the registers. From Russell King.
9) Fix non-forced handling in u32_destroy(), from WANG Cong.
10) Test the EVENT_NO_RUNTIME_PM flag before it is cleared in
usbnet_stop(), from Eugene Shatokhin.
11) In sfc driver, don't fetch statistics firmware isn't capable of,
from Bert Kenward.
12) Verify ASCONF address parameter location in SCTP, from Xin Long"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
sctp: donot reset the overall_error_count in SHUTDOWN_RECEIVE state
sctp: asconf's process should verify address parameter is in the beginning
sfc: only use vadaptor stats if firmware is capable
net: phy: fixed: propagate fixed link values to struct
usbnet: Get EVENT_NO_RUNTIME_PM bit before it is cleared
drivers: net: xgene: fix: Oops in linkwatch_fire_event
cls_u32: complete the check for non-forced case in u32_destroy()
net: fec: use reinit_completion() in mdio accessor functions
net: phy: add locking to phy_read_mmd_indirect()/phy_write_mmd_indirect()
vxlan: re-ignore EADDRINUSE from igmp_join
net: compile renesas directory if NET_VENDOR_RENESAS is configured
ip6_gre: release cached dst on tunnel removal
phylib: Make PHYs children of their MDIO bus, not the bus' parent.
can: pcan_usb: don't provide CAN FD bittimings by non-FD adapters
net: Fix RCU splat in af_key
net: bcmgenet: fix uncleaned dma flags
net: bcmgenet: Avoid sleeping in bcmgenet_timeout
netlink: mmap: fix tx type check
Pull nvdimm fixlet from Dan Williams:
"This is a libnvdimm ABI fixup.
I pushed back on this change quite hard given the late date, that it
appears to be purely cosmetic, sysfs is not necessarily meant to be a
user friendly UI, and the kernel interprets the reversed polarity of
the ACPI_NFIT_MEM_ARMED flag correctly. When this flag is set, the
energy source of an NVDIMM is not armed and any new writes to the DIMM
may not be preserved.
However, Bob Moore warned me that it is important to get these things
named correctly wherever they appear otherwise we run the risk of a
less than cautious firmware engineer implementing the polarity the
wrong way. Once a mistake like that escapes into production platforms
the flag becomes useless and we need to move to a new bit position.
Bob has agreed to take a change through ACPICA to rename
ACPI_NFIT_MEM_ARMED to ACPI_NFIT_MEM_NOT_ARMED, and the patch below
from Toshi brings the sysfs representation of these flags in line with
their respective polarities.
Please pull for 4.2 as this is the first kernel to expose the ACPI
NFIT sysfs representation, and this is likely a kernel that firmware
developers will be using for checking out their NVDIMM enabling"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: Clarify memory device state flags strings
Phil Sutter says:
====================
fixup IFF_NO_QUEUE conversion
This series serves two purposes:
On one hand it fixes a quite embarrassing bug around the warning I added for
drivers still setting tx_queue_len = 0 to achieve noqueue operation. It turned
out to be quite useless as due to using alloc_netdev(), many in-kernel drivers
fell into the trap by accident, as well. Instead this place serves pretty well
as a sanitizing point to set IFF_NO_QUEUE for drivers not initializing
tx_queue_len, which in turn allows to drop all special treatment of the latter
being zero since that can not happen anymore without IFF_NO_QUEUE being set.
On the other hand, it provides a better solution for Eric Dumazet's concern
regarding how to assign noqueue to an interface which does not default to it
already. In order to make this possible, noqueue is being registered so users
can 'tc qd add dev eth0 root noqueue'. In addition, it resolves the ugly
situation of 'tc qd show' not showing noqueue. Finally, the former changes
allow for some code cleanup.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that noqueue qdisc can be attached just like any other qdisc, no
special treatment is necessary anymore when attaching it as default
qdisc.
This change has the added benefit that 'tc qdisc show' prints noqueue
instead of nothing for devices defaulting to noqueue.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
This way users can attach noqueue just like any other qdisc using tc
without having to mess with tx_queue_len first.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since alloc_netdev_mqs() sets IFF_NO_QUEUE for drivers not initializing
tx_queue_len, it is safe to assume that if tx_queue_len is zero,
dev->priv flags always contains IFF_NO_QUEUE.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Printing a warning in alloc_netdev_mqs() if tx_queue_len is zero and
IFF_NO_QUEUE not set is not appropriate since drivers may use one of the
alloc_netdev* macros instead of alloc_etherdev*, thereby not
intentionally leaving tx_queue_len uninitialized. Instead check here if
tx_queue_len is zero and set IFF_NO_QUEUE, so the value of tx_queue_len
can be ignored in net/sched_generic.c.
Fixes: 906470c ("net: warn if drivers set tx_queue_len = 0")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The symbol '__sk_reclaim' is not present in the current tree. Apparently
'__sk_reclaim' was meant to be '__sk_mem_reclaim', so fix it with the
right symbol name for the kernel doc.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Cc: Hideo Aoki <haoki@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f8d9605243 ("sctp: Enforce retransmission limit during shutdown")
fixed a problem with excessive retransmissions in the SHUTDOWN_PENDING by not
resetting the association overall_error_count. This allowed the association
to better enforce assoc.max_retrans limit.
However, the same issue still exists when the association is in SHUTDOWN_RECEIVED
state. In this state, HB-ACKs will continue to reset the overall_error_count
for the association would extend the lifetime of association unnecessarily.
This patch solves this by resetting the overall_error_count whenever the current
state is small then SCTP_STATE_SHUTDOWN_PENDING. As a small side-effect, we
end up also handling SCTP_STATE_SHUTDOWN_ACK_SENT and SCTP_STATE_SHUTDOWN_SENT
states, but they are not really impacted because we disable Heartbeats in those
states.
Fixes: Commit f8d9605243 ("sctp: Enforce retransmission limit during shutdown")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The uninitialized value name in mlx4_en_activate_cq was used in order
to print an error message. Fixing it by replacing it with cq->vector.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently manage IRQs in pool_bm which is a bit field
of MAX_MSIX bits. Thus, allocating more than MAX_MSIX
interrupts can't be managed in pool_bm.
Fixing this by capping number of requested MSIXs to
MAX_MSIX.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking into fixing the local entries scalability issue I noticed
that the structure is badly arranged because vlan_id would fall in a
second cache line while keeping rcu which is used only when deleting
in the first, so re-arrange the structure and push rcu to the end so we
can get 16 bytes which can be used for other fields (by pushing rcu
fully in the second 64 byte chunk). With this change all the core
necessary information when doing fdb lookups will be available in a
single cache line.
pahole before (note vlan_id):
struct net_bridge_fdb_entry {
struct hlist_node hlist; /* 0 16 */
struct net_bridge_port * dst; /* 16 8 */
struct callback_head rcu; /* 24 16 */
long unsigned int updated; /* 40 8 */
long unsigned int used; /* 48 8 */
mac_addr addr; /* 56 6 */
unsigned char is_local:1; /* 62: 7 1 */
unsigned char is_static:1; /* 62: 6 1 */
unsigned char added_by_user:1; /* 62: 5 1 */
unsigned char added_by_external_learn:1; /* 62: 4 1 */
/* XXX 4 bits hole, try to pack */
/* XXX 1 byte hole, try to pack */
/* --- cacheline 1 boundary (64 bytes) --- */
__u16 vlan_id; /* 64 2 */
/* size: 72, cachelines: 2, members: 11 */
/* sum members: 65, holes: 1, sum holes: 1 */
/* bit holes: 1, sum bit holes: 4 bits */
/* padding: 6 */
/* last cacheline: 8 bytes */
}
pahole after (note vlan_id):
struct net_bridge_fdb_entry {
struct hlist_node hlist; /* 0 16 */
struct net_bridge_port * dst; /* 16 8 */
long unsigned int updated; /* 24 8 */
long unsigned int used; /* 32 8 */
mac_addr addr; /* 40 6 */
__u16 vlan_id; /* 46 2 */
unsigned char is_local:1; /* 48: 7 1 */
unsigned char is_static:1; /* 48: 6 1 */
unsigned char added_by_user:1; /* 48: 5 1 */
unsigned char added_by_external_learn:1; /* 48: 4 1 */
/* XXX 4 bits hole, try to pack */
/* XXX 7 bytes hole, try to pack */
struct callback_head rcu; /* 56 16 */
/* --- cacheline 1 boundary (64 bytes) was 8 bytes ago --- */
/* size: 72, cachelines: 2, members: 11 */
/* sum members: 65, holes: 1, sum holes: 7 */
/* bit holes: 1, sum bit holes: 4 bits */
/* last cacheline: 8 bytes */
}
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Stringer says:
====================
OPENVSWITCH && !NETFILTER build fix.
Fix issues reported by kbuild test robot:
All error/warnings (new ones prefixed by >>):
net/openvswitch/actions.c: In function 'ovs_fragment':
>> net/openvswitch/actions.c:705:16: error: implicit declaration of
function 'nf_get_ipv6_ops' [-Werror=implicit-function-declaration]
const struct nf_ipv6_ops *v6ops = nf_get_ipv6_ops();
^
>> net/openvswitch/actions.c:705:37: warning: initialization makes
pointer from integer without a cast
const struct nf_ipv6_ops *v6ops = nf_get_ipv6_ops();
^
>> net/openvswitch/actions.c:707:19: error: storage size of 'ovs_rt'
isn't known
struct rt6_info ovs_rt;
^
>> net/openvswitch/actions.c:724:8: error: dereferencing pointer to
incomplete type
v6ops->fragment(skb->sk, skb, ovs_vport_output);
^
>> net/openvswitch/actions.c:707:19: warning: unused variable 'ovs_rt'
[-Wunused-variable]
struct rt6_info ovs_rt;
^
cc1: some warnings being treated as errors
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
kbuild test robot reports that certain configurations will not
automatically pick up on the "struct rt6_info" definition, so explicitly
include the header for this structure.
Fixes: 7f8a436 "openvswitch: Add conntrack action"
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_OPENVSWITCH is set, and CONFIG_NETFILTER is not set, the
openvswitch IPv6 fragmentation handling cannot refer to ipv6_ops because
it isn't defined. Add a dummy version to avoid #ifdefs in source files.
Fixes: 7f8a436 "openvswitch: Add conntrack action"
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HW-SW contract requires mailboxes passed to the firmware to be 4KB
aligned. Previously, these mailboxes were mapped using streaming DMA
routines, which do not guarantee the bus addresses to be 4KB aligned.
Under certain conditions this constraint was indeed violated and errors
were observed.
By using consistent DMA mapping routines together with a mailbox size of
4KB we are guaranteed not to violate the constraint.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When transmit fails, it is an error, not a warning.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
rocker: make master change handling nicer
Jiri Pirko (6):
net: introduce change upper device notifier change info
net: add netif_is_bridge_master helper
net: add netif_is_ovs_master helper with IFF_OPENVSWITCH private flag
net: kill long time unused bonding private flags
rocker: use new helper to figure out master kind
rocker: use change upper info
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since now information about changed upper is passed along, benefit from
that and use this info directly.
This also fixes possible issues that could happen when non-master device
is added (current code does not distinguish between master and non-master
upper device).
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Looking at rtnl kind string is kind of ugly. So use new helpers to do
this in nicer way.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Add this helper so code can easily figure out if netdev is openswitch.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add this helper so code can easily figure out if netdev is a bridge.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add info that is passed along with NETDEV_CHANGEUPPER event.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usually an skb does not have up to MAX_SKB_FRAGS frags. So no need to
initialize the unuse part of sg. This patch initialize the sg based on
the real number it will used:
- during xmit, it could be inferred from nr_frags and can_push.
- for small receive buffer, it will also be 2.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar says:
====================
Geneve: Add support for tunnel metadata mode
Following patches adds support for Geneve tunnel metadata
mode. OVS can make use of Geneve net-device with tunnel
metadata API from kernel.
This also allows us to consolidate Geneve implementation
from two kernel modules geneve_core and geneve to single
geneve module. geneve_core module was targeted to share
Geneve encap and decap code between Geneve netdevice and
OVS Geneve tunnel implementation, Since OVS no longer
needs these API, Geneve code can be consolidated into
single geneve module.
v3-v4:
- Drop NETIF_F_NETNS_LOCAL feature.
- Fix geneve device newlink check
v2-v3:
- make tunnel medata device and regular device mutually exclusive.
- Fix Kconfig dependency for Geneve.
- Fix dst-port netlink encoding.
- drop changelink patch.
v1-v2:
- Replaced per hash table tunnel pointer (metadata enabled) with flag.
- Added support for changelink.
- Improve geneve device route lookup with more parameters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This change simplifies Geneve Tunnel hash table management.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Reviewed-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
geneve_core module handles send and receive functionality.
This way OVS could use the Geneve API. Now with use of
tunnel meatadata mode OVS can directly use Geneve netdevice.
So there is no need for separate module for Geneve. Following
patch consolidates Geneve protocol processing in single module.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With help of tunnel metadata mode OVS can directly use
Geneve devices to implement Geneve tunnels.
This patch removes all of the OVS specific Geneve code
and make OVS use a Geneve net_device. Basic geneve vport
is still there to handle compatibility with current
userspace application.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch create new tunnel flag which enable
tunnel metadata collection on given device. These devices
can be used by tunnel metadata based routing or by OVS.
Geneve Consolidation patch get rid of collect_md_tun to
simplify tunnel lookup further.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netlink interface to configure Geneve UDP port number.
So that user can configure it for a Gevene device.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann
Shradha Shah
Hariprasad Shenai
David S. Miller
Valentin Rothberg
David Ahern
Chas Williams
Philip Downey
Corinna Vinschen
Linus Torvalds
Phil Sutter
Jean Sacren
lucien
Carol L Soto
Nikolay Aleksandrov
Joe Stringer
Ido Schimmel
Jiri Pirko
Jason Wang
Pravin B Shelar