If CONFIG_ARCH_DMA_ADDR_T_64BIT enabled for x86 systems and physical
memory is more than 4GB, dma_map_page may return a valid memory
address which greater than 0xffffffff. As a result, the mlx5 device page
allocator RB tree will be initialized with valid addresses greater than
0xfffffff.
However, (addr & PAGE_MASK) set the high four bytes to zeros. So, it's
impossible for the function, free_4k, to release the pages whose
addresses greater than 4GB. Memory leaks. And mlx5_ib module can't
release the pages when user try to remove the module, as a result,
system hang.
[root@rdma05 root]# dmesg | grep addr | head
addr = 3fe384000
addr & PAGE_MASK = fe384000
[root@rdma05 root]# rmmod mlx5_ib <---- hang on
---------------------- cosnole log -----------------
mlx5_ib 0000:04:00.0: irq 138 for MSI/MSI-X
alloc irq_desc for 139 on node -1
alloc kstat_irqs on node -1
mlx5_ib 0000:04:00.0: irq 139 for MSI/MSI-X
0000:04:00.0:free_4k:221:(pid 1519): page not found
0000:04:00.0:free_4k:221:(pid 1519): page not found
0000:04:00.0:free_4k:221:(pid 1519): page not found
0000:04:00.0:free_4k:221:(pid 1519): page not found
---------------------- cosnole log -----------------
Fixes: bf0bf77f65 ('mlx5: Support communicating arbitrary host page size to firmware')
Signed-off-by: Honggang Li <honli@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In some rare cases, IO operations may be not aligned to page
boundaries. This prevents iser from performing fast memory
registration. In order to overcome that iser uses a bounce
buffer to carry the transaction. We basically allocate a buffer
in the size of the transaction and perform a copy.
The buffer allocation using kmalloc is too restrictive since it
requires higher order (atomic) allocations for large transactions
(which may result in memory exhaustion fairly fast for some workloads).
We rewrite the bounce buffer code path to allocate scattered pages
and perform a copy between the transaction sg and the bounce sg.
Reported-by: Alex Lyakas <alex@zadarastorage.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In singleton scatterlists, DMA memory registration code
is taken both for Fastreg and FMR code paths. Move it to
a function.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Adir Lev <adirl@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Instead of passing ib_sge as output variable, we pass the mem_reg
pointer to have the routines fill the rkey as well. This reduces
code duplication and extra assignments. This is a preparation step
to unify some registration logics together. Also, pass iser_fast_reg_mr
the fastreg descriptor directly.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Adir Lev <adirl@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
No need to keep lkey, va, len variables, we can keep
them as struct ib_sge. This will help when we change the
memory registration logic.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Adir Lev <adirl@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Memory regions are resources that are saved
in the device caches. Increase the probability for
a cache hit by adding the MRU descriptor to pool
head.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Make iser_[create|destroy]_fastreg_desc shorter, more
readable and easily extendable.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Adir Lev <adirl@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Instead of open-coding connection fastreg pool get/put,
we introduce iser_reg_desc[get|put] helpers.
We aren't setting these static as this will be a per-device
routine later on. Also, cleanup iser_unreg_rdma_mem_fastreg
a bit.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Adir Lev <adirl@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
No need for these two separate. Keep it in a single routine
like in the fastreg case. This will also make iser_reg_page_vec
closer to iser_fast_reg_mr arguments. This is a preparation
step for registration flow refactor.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Adir Lev <adirl@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This struct members other than struct iser_mem_reg are unused,
so remove it altogether.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Adir Lev <adirl@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Buffer length was assigned twice, and no reason to set va to
io_addr and then add the offset, just set va to io_addr + offset.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Adir Lev <adirl@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
As memory registration/de-registration methods, lets
move them to their natural location. While we're at it,
make iser_reg_page_vec routine static.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
No need to pass that, we can take it from the task.
In a later stage, this function will be invoked
according to a device capability.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Adir Lev <adirl@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
No need to keep two iser_data_buf structures just in case we use
mem copy. We can avoid that just by adding a pointer to the original
sg. So keep only two iser_data_buf per command (data and protection)
and pass the relevant data_buf to bounce buffer routine.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Adir Lev <adirl@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This code was added before we had protection data length
calculation (in iser_send_command), so we needed to calc
the sg data length from the sg itself. This is not needed
anymore.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Adir Lev <adirl@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This length miss-calculation may cause a silent data corruption
in the DIX case and cause the device to reference unmapped area.
Fixes: d77e65350f ('libiscsi, iser: Adjust data_length to include protection information')
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fast registration and local invalidate work requests can
also fail. We should call error completion handler for them.
Reported-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In case the user unloaded ib_iser while ep_connect is in
progress, we need to destroy the endpoint although ep_disconnect
wasn't invoked (we detect this by the iser conn state != DOWN).
However, if we got an REJECTED/UNREACHABLE CM event we move the
connection state to DOWN which will prevent us from destroying
the endpoint in the module unload stage. Fix this by setting the
connection state to TERMINATING in iser_conn_error so we can still
destroy the endpoint at unload stage.
Reported-by: Ariel Nahum <arieln@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The driver already defined the pr_format, it just hadn't
been converted to use pr_info, pr_warn, and pr_err instead
of the equivalent printks. Convert so that messages from
the driver are now properly tagged with their driver name
and can be more easily debugged.
In addition, a number of these printk's were not newline
terminated, so fix that at the same time.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This change slightly reduces the time needed to log in.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: David Dillow <dave@thedillows.org>
Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Since ib_dma_map_single can fail use ib_dma_mapping_error to check
for errors.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Updating the MAINTAINERS file with ocrdma maintainers and their email ids
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The ifconfig command has been deprecated for many years.
To encourage new users not to continue using it and learning
iproute2; the ifconfig should not be used in examples.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Hello,
When an application using XRCs abruptly terminates, the mmaped pages
of the CQ buffers are leaked.
This comes from the fact that when resources are released in
ib_uverbs_cleanup_ucontext(), we fail to release the CQs because their
refcount is not 0.
When creating an XRC SRQ, we increment the associated CQ refcount.
This refcount is only decremented when the SRQ is released.
Therefore we need to release the SRQs prior to the CQs to make sure
that all references to the CQs are gone before trying to release these.
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The current code decreases from the mss size (which is the gso_size
from the kernel skb) the size of the packet headers.
It shouldn't do that because the mss that comes from the stack
(e.g IPoIB) includes only the tcp payload without the headers.
The result is indication to the HW that each packet that the HW sends
is smaller than what it could be, and too many packets will be sent
for big messages.
An easy way to demonstrate one more aspect of the problem is by
configuring the ipoib mtu to be less than 2*hlen (2*56) and then
run app sending big TCP messages. This will tell the HW to send packets
with giant (negative value which under unsigned arithmetics becomes
a huge positive one) length and the QP moves to SQE state.
Fixes: b832be1e40 ('IB/mlx4: Add IPoIB LSO support')
Reported-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
After Doug Ledford's changes there is no need in that bit, it's
semantic becomes subset of the IPOIB_FLAG_OPER_UP bit.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Whenever there is no path->ah to the destination, keep only defined
number of skb's. Otherwise there are cases that the driver can keep
infinite list of skb's.
For example, when one device want to send unicast arp to the destination,
and from some reason the SM doesn't respond, the driver currently keeps
all the skb's. If that unicast arp traffic stopped, all these skb's
are kept by the path object till the interface is down.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
As the result of a completion error the QP can moved to SQE state by
the hardware. Since it's not the Error state, there are no flushes
and hence the driver doesn't know about that.
The fix creates a task that after completion with error which is not a
flush tracks the QP state and if it is in SQE state moves it back to RTS.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Update the cached broadcast record in the priv object after every new
join of this broadcast domain group.
These values are needed for the port configuration (MTU size) and to
all the new multicast (non-broadcast) join requests initial parameters.
For example, SM starts with 2K MTU for all the fabric, and after that it
restarts (or handover to new SM) with new port configuration of 4K MTU.
Without using the new values, the driver will keep its old configuration
of 2K and will not apply the new configuration of 4K.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The current code in the RX flow uses two sg entries for each incoming
packet, the first one was for the IB headers and the second for the rest
of the data, that causes two dma map/unmap and two allocations, and few
more actions that were done at the data path.
Use only one linear skb on each incoming packet, for the data (IB
headers and payload), that reduces the packet processing in the
data-path (only one skb, no frags, the first frag was not used anyway,
less memory allocations) and the dma handling (only one dma map/unmap
over each incoming packet instead of two map/unmap per each incoming packet).
After commit 73d3fe6d1c ("gro: fix aggregation for skb using frag_list") from
Eric Dumazet, we will get full aggregation for large packets.
When running bandwidth tests before and after the (over the card's numa node),
using "netperf -H 1.1.1.3 -T -t TCP_STREAM", the results before are ~12Gbs before
and after ~16Gbs on my setup (Mellanox's ConnectX3).
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We needed the mcast_mutex when we had to prevent the join completion
callback from having the value it stored in mcast->mc overwritten
by a delayed return from ib_sa_join_multicast. By storing the return
of ib_sa_join_multicast in an intermediate variable, we prevent a
delayed return from ib_sa_join_multicast overwriting the valid
contents of mcast->mc, and we no longer need a mutex to force the
join callback to run after the return of ib_sa_join_multicast. This
allows us to do away with the mutex entirely and protect our critical
sections with a just a spinlock instead. This is highly desirable
as there were some places where we couldn't use a mutex because the
code was not allowed to sleep, and so we were currently using a mix
of mutex and spinlock to protect what we needed to protect. Now we
only have a spin lock and the locking complexity is greatly reduced.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Allow the ipoib layer to attempt to join all outstanding multicast
groups at once. The ib_sa layer will serialize multiple attempts to
join the same group, but will process attempts to join different groups
in parallel. Take advantage of that.
In order to make this happen, change the mcast_join_thread to loop
through all needed joins, sending a join request for each one that we
still need to join. There are a few special cases we handle though:
1) Don't attempt to join anything but the broadcast group until the join
of the broadcast group has succeeded.
2) No longer restart the join task at the end of completion handling.
If we completed successfully, we are done. The join task now needs kicked
either by mcast_send or mcast_restart_task or mcast_start_thread, but
should not need started anytime else except when scheduling a backoff
attempt to rejoin.
3) No longer use separate join/completion routines for regular and
sendonly joins, pass them all through the same routine and just do the
right thing based on the SENDONLY join flag.
4) Only try to join a SENDONLY join twice, then drop the packets and
quit trying. We leave the mcast group in the list so that if we get a
new packet, all that we have to do is queue up the packet and restart
the join task and it will automatically try to join twice and then
either send or flush the queue again.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Commit a9c8ba5884 ("IPoIB: Fix usage of uninitialized multicast
objects") added a new flag MCAST_JOIN_STARTED, but was not very strict
in how it was used. We didn't always initialize the completion struct
before we set the flag, and we didn't always call complete on the
completion struct from all paths that complete it. And when we did
complete it, sometimes we continued to touch the mcast entry after
the completion, opening us up to possible use after free issues.
This made it less than totally effective, and certainly made its use
confusing. And in the flush function we would use the presence of this
flag to signal that we should wait on the completion struct, but we never
cleared this flag, ever.
In order to make things clearer and aid in resolving the rtnl deadlock
bug I've been chasing, I cleaned this up a bit.
1) Remove the MCAST_JOIN_STARTED flag entirely
2) Change MCAST_FLAG_BUSY so it now only means a join is in-flight
3) Test mcast->mc directly to see if we have completed
ib_sa_join_multicast (using IS_ERR_OR_NULL)
4) Make sure that before setting MCAST_FLAG_BUSY we always initialize
the mcast->done completion struct
5) Make sure that before calling complete(&mcast->done), we always clear
the MCAST_FLAG_BUSY bit
6) Take the mcast_mutex before we call ib_sa_multicast_join and also
take the mutex in our join callback. This forces
ib_sa_multicast_join to return and set mcast->mc before we process
the callback. This way, our callback can safely clear mcast->mc
if there is an error on the join and we will do the right thing as
a result in mcast_dev_flush.
7) Because we need the mutex to synchronize mcast->mc, we can no
longer call mcast_sendonly_join directly from mcast_send and
instead must add sendonly join processing to the mcast_join_task
8) Make MCAST_RUN mean that we have a working mcast subsystem, not that
we have a running task. We know when we need to reschedule our
join task thread and don't need a flag to tell us.
9) Add a helper for rescheduling the join task thread
A number of different races are resolved with these changes. These
races existed with the old MCAST_FLAG_BUSY usage, the
MCAST_JOIN_STARTED flag was an attempt to address them, and while it
helped, a determined effort could still trip things up.
One race looks something like this:
Thread 1 Thread 2
ib_sa_join_multicast (as part of running restart mcast task)
alloc member
call callback
ifconfig ib0 down
wait_for_completion
callback call completes
wait_for_completion in
mcast_dev_flush completes
mcast->mc is PTR_ERR_OR_NULL
so we skip ib_sa_leave_multicast
return from callback
return from ib_sa_join_multicast
set mcast->mc = return from ib_sa_multicast
We now have a permanently unbalanced join/leave issue that trips up the
refcounting in core/multicast.c
Another like this:
Thread 1 Thread 2 Thread 3
ib_sa_multicast_join
ifconfig ib0 down
priv->broadcast = NULL
join_complete
wait_for_completion
mcast->mc is not yet set, so don't clear
return from ib_sa_join_multicast and set mcast->mc
complete
return -EAGAIN (making mcast->mc invalid)
call ib_sa_multicast_leave
on invalid mcast->mc, hang
forever
By holding the mutex around ib_sa_multicast_join and taking the mutex
early in the callback, we force mcast->mc to be valid at the time we
run the callback. This allows us to clear mcast->mc if there is an
error and the join is going to fail. We do this before we complete
the mcast. In this way, mcast_dev_flush always sees consistent state
in regards to mcast->mc membership at the time that the
wait_for_completion() returns.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Various places in the IPoIB code had a deadlock related to flushing
the ipoib workqueue. Now that we have per device workqueues and a
specific flush workqueue, there is no longer a deadlock issue with
flushing the device specific workqueues and we can do so unilaterally.
Signed-off-by: Doug Ledford <dledford@redhat.com>
During my recent work on the rtnl lock deadlock in the IPoIB driver, I
saw that even once I fixed the apparent races for a single device, as
soon as that device had any children, new races popped up. It turns
out that this is because no matter how well we protect against races
on a single device, the fact that all devices use the same workqueue,
and flush_workqueue() flushes *everything* from that workqueue means
that we would also have to prevent all races between different devices
(for instance, ipoib_mcast_restart_task on interface ib0 can race with
ipoib_mcast_flush_dev on interface ib0.8002, resulting in a deadlock on
the rtnl_lock).
There are several possible solutions to this problem:
Make carrier_on_task and mcast_restart_task try to take the rtnl for
some set period of time and if they fail, then bail. This runs the
real risk of dropping work on the floor, which can end up being its
own separate kind of deadlock.
Set some global flag in the driver that says some device is in the
middle of going down, letting all tasks know to bail. Again, this can
drop work on the floor.
Or the method this patch attempts to use, which is when we bring an
interface up, create a workqueue specifically for that interface, so
that when we take it back down, we are flushing only those tasks
associated with our interface. In addition, keep the global
workqueue, but now limit it to only flush tasks. In this way, the
flush tasks can always flush the device specific work queues without
having deadlock issues.
Signed-off-by: Doug Ledford <dledford@redhat.com>
We blindly assume that we can just take the rtnl lock and that will
prevent races with downing this interface. Unfortunately, that's not
the case. In ipoib_mcast_stop_thread() we will call flush_workqueue()
in an attempt to clear out all remaining instances of ipoib_join_task.
But, since this task is put on the same workqueue as the join task,
the flush_workqueue waits on this thread too. But this thread is
deadlocked on the rtnl lock. The better thing here is to use trylock
and loop on that until we either get the lock or we see that
FLAG_OPER_UP has been cleared, in which case we don't need to do
anything anyway and we just return.
While investigating which flag should be used, FLAG_ADMIN_UP or
FLAG_OPER_UP, it was determined that FLAG_OPER_UP was the more
appropriate flag to use. However, there was a mix of these two flags in
use in the existing code. So while we check for that flag here as part
of this race fix, also cleanup the two places that had used the less
appropriate flag for their tests.
Signed-off-by: Doug Ledford <dledford@redhat.com>
The ipoib_mcast_flush_dev routine is called with the rtnl_lock held and
needs to keep it held. It also needs to call flush_workqueue() to flush
out any outstanding work. In the past, we've had to try and make sure
that we didn't flush out any outstanding join completions because they
also wanted to grab rtnl_lock() and that would deadlock. It turns out
that the only thing in the join completion handler that needs this lock
can be safely moved to our carrier_on_task, thereby reducing the
potential for the join completion code and the flush code to deadlock
against each other.
Signed-off-by: Doug Ledford <dledford@redhat.com>
In preparation for using per device work queues, we need to move the
start of the neighbor thread task to after ipoib_ib_dev_init and move
the destruction of the neighbor task to before ipoib_ib_dev_cleanup.
Otherwise we will end up freeing our workqueue with work possibly
still on it.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Create a an ipoib_flush_ah and ipoib_stop_ah routines to use at
appropriate times to flush out all remaining ah entries before we shut
the device down.
Because neighbors and mcast entries can each have a reference on any
given ah, we must make sure to free all of those first before our ah
will actually have a 0 refcount and be able to be reaped.
This factoring is needed in preparation for having per-device work
queues. The original per-device workqueue code resulted in the following
error message:
<ibdev>: ib_dealloc_pd failed
That error was tracked down to this issue. With the changes to which
workqueues were flushed when, there were no flushes of the per device
workqueue after the last ah's were freed, resulting in an attempt to
dealloc the pd with outstanding resources still allocated. This code
puts the explicit flushes in the needed places to avoid that problem.
Signed-off-by: Doug Ledford <dledford@redhat.com>
In a call to ib_umem_get(), if address is 0x0 and size is
already page aligned, check added in commit 8494057ab5
("IB/uverbs: Prevent integer overflow in ib_umem_get address
arithmetic") will refuse to register a memory region that
could otherwise be valid (provided vm.mmap_min_addr sysctl
and mmap_low_allowed SELinux knobs allow userspace to map
something at address 0x0).
This patch allows back such registration: ib_umem_get()
should probably don't care of the base address provided it
can be pinned with get_user_pages().
There's two possible overflows, in (addr + size) and in
PAGE_ALIGN(addr + size), this patch keep ensuring none
of them happen while allowing to pin memory at address
0x0. Anyway, the case of size equal 0 is no more (partially)
handled as 0-length memory region are disallowed by an
earlier check.
Link: http://mid.gmane.org/cover.1428929103.git.ydroneaud@opteya.com
Cc: <stable@vger.kernel.org> # 8494057ab5 ("IB/uverbs: Prevent integer overflow in ib_umem_get address arithmetic")
Cc: Shachar Raindel <raindel@mellanox.com>
Cc: Jack Morgenstein <jackm@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If ib_umem_get() is called with a size equal to 0 and an
non-page aligned address, one page will be pinned and a
0-sized umem will be returned to the caller.
This should not be allowed: it's not expected for a memory
region to have a size equal to 0.
This patch adds a check to explicitly refuse to register
a 0-sized region.
Link: http://mid.gmane.org/cover.1428929103.git.ydroneaud@opteya.com
Cc: <stable@vger.kernel.org>
Cc: Shachar Raindel <raindel@mellanox.com>
Cc: Jack Morgenstein <jackm@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Change the default mode to be HOST assigned instead of SM assigned. This is
the expected operational mode, because it doesn't depend on SM availability.
As PF generates random GUIDs as the initial admin values, this gives
out of the box experience.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Return the admin alias GUID value upon a GET request via HOST. We do this so
that the GUID value requested by the admin is returned even if the SM has not
yet approved this GUID (e.g. the SM is down).
Note that this does not create a problem, since the virtual port will remain
down until the SM does ACK the requested GUID value.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There might be cases that PF doesn't get a "reset" command upon slave down
(e.g. virsh destroy). In these cases, however, an FLR event is issued.
Therefore, when the PF receives an FLR event for a slave, it should also
generate a shutdown event on the PF for that slave, to let the PF upper
layers (mlx4_ib, eth) perform any required cleanup/actions associated
with slave shutdown.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Request GIDs from the SM on demand, i.e., when a VF actually needs them,
and release them when the GIDs are no longer in use.
In cloud environments, this is useful for GID migrations, in which a
GID is assigned to a VF on the destination HCA, while the VF on the
source HCA is shutdown (but the GID was not administratively released).
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Change the init flow to ask GUIDs only for active VFs. This is done for
both SM & HOST modes so that there is no need any more to maintain the
ownership record type.
In case SM mode is used, the initial value will be 0, ask the SM to assign,
for the HOST mode the initial value will be the HOST generated GUID.
This will enable out of the box experience for both probed and attached VFs.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Set the admin alias GUID per the administrator's request via the sysfs
mechanism into the core layer.
The "get" request returns the current value. However, if the administrator
requests the SM to assign a new value by requesting 0, the SM assigned
GUID is returned.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
To have out of the box experience, the PF generates random GUIDs who
serve as the initial admin values.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Doug Ledford
Honggang LI
Sagi Grimberg
Bart Van Assche
Sebastian Ott
Selvin Xavier
Stephen Hemminger
Sébastien Dugué
Erez Shitrit
Yann Droneaud
Yishai Hadas