Add a DTS for TL-WR1043ND version 1 and allow to have it built in the
kernel to circumvent the broken u-boot found on these boards.
Currently only the UART, LEDs and buttons are supported.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace the simple GPIO chip registration by a platform driver
and make ath79_gpio_init() just register the device.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Allow using the SoC clocks in the device tree.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add OF support for the CPU and MISC interrupt controllers of most
supported ATH79 devices.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add the bare minimum to load a device tree.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make the code simpler and open the way for device tree clocks.
[ralf@linux-mips.org: Resolved conflict with 2a552da6 (MIPS/IRQCHIP: Move
irq_chip from arch/mips to drivers/irqchip.)]
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9774/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The DDR controller need to be used by the IRQ controller to flush
the write buffer of some devices before running the IRQ handler.
It is also used by the PCI controller to setup the PCI memory windows.
The current interface used to access the DDR controller doesn't
provides any useful abstraction and simply rely on a shared global
pointer.
Replace this by a simple API to setup the PCI memory windows and use
the write buffer flush independently of the SoC type. That remove the
need for the shared global pointer, simplify the IRQ handler code.
[ralf@linux-mips.org: Folded in Alban Bedel's follup fix.]
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9773/
Patchwork: http://patchwork.linux-mips.org/patch/10543/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This register is named PLL_FB and is not a divider but a multiplier.
To make things less confusing rename the ARxxxx_PLL_DIV_SHIFT and
ARxxxx_PLL_DIV_MASK macros to ARxxxx_PLL_FB_SHIFT and
ARxxxx_PLL_FB_MASK.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9772/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
At least QCA955x can handle up to 256MBytes.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: linux-mips@linux-mips.org
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Patchwork: https://patchwork.linux-mips.org/patch/8738/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The hardware perf event driver and oprofile interpret the global
cp0_perfcount_irq differently: in the hardware perf event driver
it is an offset from MIPS_CPU_IRQ_BASE and in oprofile it is the
actual IRQ number. This still works most of the time since
MIPS_CPU_IRQ_BASE is usually 0, but is clearly wrong. Since the
performance counter interrupt may vary from platform to platform
like the C0 timer interrupt, add the optional get_c0_perfcount_int
hook which returns the IRQ number of the performance counter.
The hook should return < 0 if the performance counter interrupt is
shared with the timer. If the hook is not present, the CPU vector
reported in C0_IntCtl (cp0_perfcount_irq) is used.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Tested-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Jeffrey Deans <jeffrey.deans@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7805/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When CONFIG_PCI is disabled, 'db120_pci_init()' had a different
signature than when was enabled. Therefore, compilation failed when
CONFIG_PCI was not present.
arch/mips/ath79/mach-db120.c:132: error: too many arguments to function 'db120_pci_init'
This error was found with vampyr.
Signed-off-by: Stefan Hengelein <stefan.hengelein@fau.de>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: geert@linux-m68k.org
Patchwork: https://patchwork.linux-mips.org/patch/8119/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
USB_ARCH_HAS_EHCI, USB_ARCH_HAS_OHCI, and USB_ARCH_HAS_XHCI were just
removed. Selecting them is a nop. The select statements for these
symbols can be removed too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6320/
In commit 15ef17f622
(tty: ar933x_uart: use the clk API to get the uart
clock), the AR933x UART driver for has been converted
to get the uart clock rate via the clock API and it
does not use the platform data anymore.
Remove the ar933x_uart_platform.h header file and get
rid of the superfluous variable and initialization code
in platform setup.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5832/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ath79 code uses static clock devices and
provides its own clk_{get,put} implementations.
Change the code to use dynamically allocated
clock devices and register the clocks within
the clkdev framework.
Additionally, remove the local clk_{get,put}
implementation. The clkdev framework has a
common implementation of those.
Also move the call of ath79_clock_init() from
plat_mem_init() to plat_time_init(). Otherwise
it would not be possible to use memory allocation
functions from ath79clock_init() becasuse the
memory subsystem is not yet initialized when
plat_mem_init() runs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5780/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use local variables for ref, cpu, ddr and ahb
rates in SoC specific clock init functions.
The patch has no functional changes, it is
an interim change in preparation of the next
patch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5781/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of accessing the rate field of the static
clock devices directly, use the recently introduced
helper function to get the rate of the basic clocks.
The static ath79_{ahb,cpu,ddr,ref}_clk variables
will be removed by a subsequent patch. The actual
change is in preparation of that.
Also move the clock frequency printing code into
the plat_time_init function. We are getting the
cpu clock rate there already so we can save an
extra call of the helper.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5782/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ath79 platform uses similar code to get the
rate of various clocks during init. Separate the
similar code into a new helper function and use
that to avoid code duplication.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5778/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The reference clock rate is passed in the first
argument of the function. Use that instead of the
rate of the global ath79_ref_clk variable.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5779/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The watchdog device on the AR933x is connected to
the AHB clock, however the current code uses the
reference clock. Due to the wrong rate, the watchdog
driver can't calculate correct register values for
a given timeout value and the watchdog unexpectedly
restarts the system.
The code uses the wrong value since the initial
commit 04225e1d22
(MIPS: ath79: add AR933X specific clock init)
The patch fixes the code to use the correct clock
rate to avoid the problem.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5777/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
commit 3747069b25e419f6b51395f48127e9812abc3596 upstream.
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings. In any case, they are temporary and harmless.
Here, we remove all the MIPS __cpuinit from C code and __CPUINIT
from asm files. MIPS is interesting in this respect, because there
are also uasm users hiding behind their own renamed versions of the
__cpuinit macros.
[1] https://lkml.org/lkml/2013/5/20/589
[ralf@linux-mips.org: Folded in Paul's followup fix.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5494/
Patchwork: https://patchwork.linux-mips.org/patch/5495/
Patchwork: https://patchwork.linux-mips.org/patch/5509/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
ap136_pci_init expects a u8 pointer as an argument.
Fixes the following build problem on a randconfig:
arch/mips/ath79/mach-ap136.c:151:2: error:
too many arguments to function 'ap136_pci_init'
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5476/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There is now a generic function for detecting memory size. Use this instead of
the one found in the ath79 support.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5149/
Pull watchdog updates from Wim Van Sebroeck:
"This contains:
- fixes and improvements
- devicetree bindings
- conversion to watchdog generic framework of the following drivers:
- booke_wdt
- bcm47xx_wdt.c
- at91sam9_wdt
- Removal of old STMP3xxx driver
- Addition of following new drivers:
- new driver for STMP3xxx and i.MX23/28
- Retu watchdog driver"
* git://www.linux-watchdog.org/linux-watchdog: (30 commits)
watchdog: sp805_wdt depends on ARM
watchdog: davinci_wdt: update to devm_* API
watchdog: davinci_wdt: use devm managed clk get
watchdog: at91rm9200: add DT support
watchdog: add timeout-sec property binding
watchdog: at91sam9_wdt: Convert to use the watchdog framework
watchdog: omap_wdt: Add option nowayout
watchdog: core: dt: add support for the timeout-sec dt property
watchdog: bcm47xx_wdt.c: add hard timer
watchdog: bcm47xx_wdt.c: rename wdt_time to timeout
watchdog: bcm47xx_wdt.c: rename ops methods
watchdog: bcm47xx_wdt.c: use platform device
watchdog: bcm47xx_wdt.c: convert to watchdog core api
watchdog: Convert BookE watchdog driver to watchdog infrastructure
watchdog: s3c2410_wdt: Use devm_* functions
watchdog: remove old STMP3xxx driver
watchdog: add new driver for STMP3xxx and i.MX23/28
rtc: stmp3xxx: add wdt-accessor function
watchdog: introduce retu_wdt driver
watchdog: intel_scu_watchdog: fix Kconfig dependency
...
The ath79_wdt driver uses a fixed memory address
currently. Although this is working with each
currently supported SoCs, but this may change
in the future. Additionally, the driver includes
platform specific header files in order to be
able to get the memory base of the watchdog
device.
The patch adds a memory resource to the platform
device, and converts the driver to get the base
address of the watchdog device from that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove the static watchdog device variable and use
the 'platform_device_register_simple' helper to
allocate and register the device in one step.
This allows us to save a few bytes in the kernel image.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Also enable the board in the default configuration.
Cc: Rodriguez, Luis <rodrigue@qca.qualcomm.com>
Cc: Giori, Kathy <kgiori@qca.qualcomm.com>
Cc: QCA Linux Team <qca-linux-team@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4953/
Signed-off-by: John Crispin <blogic@openwrt.org>
Register platfom devices for the built-in USB
controllers of the SoCs.
Cc: Rodriguez, Luis <rodrigue@qca.qualcomm.com>
Cc: Giori, Kathy <kgiori@qca.qualcomm.com>
Cc: QCA Linux Team <qca-linux-team@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4952/
Signed-off-by: John Crispin <blogic@openwrt.org>
Add SoC specific PCI IRQ map, and register platform
devices for the two built-in PCIe RCs.
Cc: Rodriguez, Luis <rodrigue@qca.qualcomm.com>
Cc: Giori, Kathy <kgiori@qca.qualcomm.com>
Cc: QCA Linux Team <qca-linux-team@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4951/
Signed-off-by: John Crispin <blogic@openwrt.org>
The SoC has a built-in wireless MAC. Register a platform
device for that to make it usable with the ath9k driver.
Cc: Rodriguez, Luis <rodrigue@qca.qualcomm.com>
Cc: Giori, Kathy <kgiori@qca.qualcomm.com>
Cc: QCA Linux Team <qca-linux-team@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4956/
Signed-off-by: John Crispin <blogic@openwrt.org>
Similarly to the preceding SoCs, the QCA955X SoCs
also have a built-in NS16650 compatible UART.
Register the platform device for that to make
it usable.
Cc: Rodriguez, Luis <rodrigue@qca.qualcomm.com>
Cc: Giori, Kathy <kgiori@qca.qualcomm.com>
Cc: QCA Linux Team <qca-linux-team@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4949/
Signed-off-by: John Crispin <blogic@openwrt.org>
The ath79_device_reset_* are causing BUG when
those are used on the QCA955x SoCs. The patch
adds the required code to avoid that.
Cc: Rodriguez, Luis <rodrigue@qca.qualcomm.com>
Cc: Giori, Kathy <kgiori@qca.qualcomm.com>
Cc: QCA Linux Team <qca-linux-team@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4948/
Signed-off-by: John Crispin <blogic@openwrt.org>
The existing code can handle the GPIO controller of
the QCA955x SoCs. Add a minimal glue code to make it
working.
Cc: Rodriguez, Luis <rodrigue@qca.qualcomm.com>
Cc: Giori, Kathy <kgiori@qca.qualcomm.com>
Cc: QCA Linux Team <qca-linux-team@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4947/
Signed-off-by: John Crispin <blogic@openwrt.org>
The IRQ routing in the QCA955x SoCs is slightly
different from the routing implemented in the
already supported SoCs.
Cc: Rodriguez, Luis <rodrigue@qca.qualcomm.com>
Cc: Giori, Kathy <kgiori@qca.qualcomm.com>
Cc: QCA Linux Team <qca-linux-team@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4955/
Signed-off-by: John Crispin <blogic@openwrt.org>
The patch adds code to get various clock frequencies
from the PLLs used in the QCA955x SoCs.
Cc: Rodriguez, Luis <rodrigue@qca.qualcomm.com>
Cc: Giori, Kathy <kgiori@qca.qualcomm.com>
Cc: QCA Linux Team <qca-linux-team@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4945/
Signed-off-by: John Crispin <blogic@openwrt.org>
Also add 'soc_is_qca955[68x]' helper functions
and a Kconfig symbol for the SoC family.
Cc: Rodriguez, Luis <rodrigue@qca.qualcomm.com>
Cc: Giori, Kathy <kgiori@qca.qualcomm.com>
Cc: QCA Linux Team <qca-linux-team@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4943/
Signed-off-by: John Crispin <blogic@openwrt.org>
The patch allows to see kernel messages on the
QCA955X SoCs in early boot stage.
Cc: Rodriguez, Luis <rodrigue@qca.qualcomm.com>
Cc: Giori, Kathy <kgiori@qca.qualcomm.com>
Cc: QCA Linux Team <qca-linux-team@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4944/
Signed-off-by: John Crispin <blogic@openwrt.org>
The '.start' field of the IRQ resource assigned twice
in ar934x_wmac_setup(). The second assignment must
set the '.end' field. Fix it.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4954/
Signed-off-by: John Crispin <blogic@openwrt.org>
The current code uses static resources and static platform
device instances for the possible USB controllers in the
system. These static variables contains initial values which
leads to data segment pollution.
Remove the static variables and use dynamically allocated
structures instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4933/
Signed-off-by: John Crispin <blogic@openwrt.org>
Use the ATH79_MISC_IRQ() macro instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4930/
Signed-off-by: John Crispin <blogic@openwrt.org>
Remove the individual ATH79_CPU_IRQ_* constants and
use the new macro instead of those.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4929/
Signed-off-by: John Crispin <blogic@openwrt.org>
The command register of the PCI controller is
not initialized correctly by the bootloader on
some boards and this leads to non working PCI
bus.
Add code to initialize the command register
from the Linux code to avoid this.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4916/
Signed-off-by: John Crispin <blogic@openwrt.org>
Static resources become impractical when multiple
PCI controllers are present. Move the resources
into the platform device registration code and
change the probe routine to get those from there
platform device's resources.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4914/
Signed-off-by: John Crispin <blogic@openwrt.org>
Alban Bedel
Laurent Fasnacht
Helmut Schaa
Andrew Bresticker
Stefan Hengelein
Paul Bolle
Paul Gortmaker
Gabor Juhos
Felix Fietkau
Markos Chandras
Ralf Baechle
John Crispin
Linus Torvalds