The commit
05fed81625 ("[media] marvell-ccic: add MIPI support for marvell-ccic driver")
that claimed to add CSI2 turned on C0_EOF_VSYNC for parallel bus
without a very good explanation.
That broke camera on OLPC XO-1.75 which precisely uses a sensor on a
parallel bus. Revert that chunk.
Tested on an OLPC XO-1.75.
Fixes: 05fed81625 ("[media] marvell-ccic: add MIPI support for marvell-ccic driver")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The commit d790b7eda9 ("[media] vb2-dma-sg: move dma_(un)map_sg here")
left dma_desc_nent unset. It previously contained the number of DMA
descriptors as returned from dma_map_sg().
We can now (since the commit referred to above) obtain the same value from
the sg_table and drop dma_desc_nent altogether.
Tested on OLPC XO-1.75 machine. Doesn't affect the OLPC XO-1's Cafe
driver, since that one doesn't do DMA.
[mchehab+samsung@kernel.org: fix a checkpatch warning]
Fixes: d790b7eda9 ("[media] vb2-dma-sg: move dma_(un)map_sg here")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
C-PHY doesn't use a clock lane, hence the test for the clock lane when
there isn't one is faulty. Rework the test for the conflicting clock lane.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the v4l2 controls are set up for autofoo/foo-type handling by calling
v4l2_ctrl_auto_cluster() with the last set_volatile argument setting true,
each non-auto control doesn't need to be flagged V4L2_CTRL_FLAG_VOLATILE.
Cc: Wenyou Yang <wenyou.yang@microchip.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Setting the value of the V4L2_CID_VFLIP control is currently ignored.
Because V4L2_CID_HFLIP and V4L2_CID_VFLIP are independently controlled
in s_ctrl() but these controls belong to the same cluster and the first
control is V4L2_CID_HFLIP.
Fix it by not clustering these controls. Also correct erroneous updating
register bit for vertical flip.
Cc: Wenyou Yang <wenyou.yang@microchip.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the requested framesize by VIDIOC_SUBDEV_S_FMT is larger than supported
framesizes, it causes an out of bounds array access and the resulting
framesize is unexpected.
Avoid out of bounds array access and select the default framesize.
Cc: Wenyou Yang <wenyou.yang@microchip.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Avoid returning without decrement the usage count in s_ctrl().
Cc: Wenyou Yang <wenyou.yang@microchip.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Document which capability is required, rather than just saying
that "root permissions" are required.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Some displays pull down the HPD when in standby, but CEC is still
active and the display can be woken up by sending an Image View On
or Text View On CEC command. The CEC specification doesn't tell you
what the initiator should be for such a command (without a HPD it's
unclear if the CEC adapter can claim a logical address).
This patch allows any initiator value when there is no HPD for the
Image/Text View On commands and for the Ping command.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If this flag is set, then check for root permissions and skip
all message checks expect for the core checks (i.e. validate the
length etc.).
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Document this new cec_msg flag.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds the userspace API to send raw unchecked CEC messages.
This will require root permissions.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This ensures all the cec_msg checks are done in the same place.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The code that fills in the CEC_MSG_CDC_MESSAGE physical address
is now done after the sanity checks. It also only does this if the
message length is >= 4 (i.e. there is room for the physical address).
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Due to limitations in gpiolib it was impossible to disable the interrupt of
an input gpio and then switch it to gpio output and drive it. The only way
to achieve that was to free the interrupt first, then switch the direction.
When going back to gpio input and using interrupts to read the gpio pin you
had to request the irq again.
This limitation was lifted in gpiolib in kernel 4.20, but the cec-gpio driver
was still using the old workaround implementation.
This patch updates the cec-gpio driver to just enable and disable the irq.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The cec device node can be used right after it was created, but that
leaves a race condition where the device was created, but devnode->registered
was still false. So an ioctl() would result in an error.
So set it to true before calling cdev_device_add() and to false again if
cdev_device_add returned an error.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove comment and replace with the appropriate SPDX identifier.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
All error cases inside the function already report errors via dev_err(),
and dvb_usb_v2_generic_rw also reports all error cases, so there is
no silent code path when an error has occurred.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Errors are already reported by the common code in dvb_usb_v2_generic_io
(which dvbsky_usb_generic_rw is a wrapper of), so there is no reason
report the error again.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
actual_length != wlen is the only error path which does not generate an
error message. Adding an error message here allows to report a more
specific error and to remove the error reporting from the call sites.
Also clean up the error paths - in case of an error, the remaining
code is skipped, and ret is returned. Skip setting ret and return
immediately (no cleanup necessary).
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
au0828_usb_disconnect() gets the au0828_dev struct via usb_get_intfdata,
so it needs to set up for the error paths.
Reported-by: syzbot+357d86bcb4cca1a2f572@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
dvb_usb_device_exit() frees and uses the device name in that order.
Fix by storing the name in a buffer before freeing it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+26ec41e9f788b3eba396@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
MODULE_DEVICE_TABLE(of, <of_match_table> should be called to complete DT
OF mathing mechanism and register it.
Before this patch:
modinfo drivers/media/rc/ir-spi.ko | grep alias
After this patch:
modinfo drivers/media/rc/ir-spi.ko | grep alias
alias: of:N*T*Cir-spi-ledC*
alias: of:N*T*Cir-spi-led
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Minimum, maximum, and stepsize taken from Silicon Labs reference.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Venus v4 doesn't send ALLOC_MODE property and thus parser doesn't
recognize it as dynamic buffer (for OUTPUT/OUTPUT2 type of buffers)
make it obvious in the helper function.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Patch commit de5a0bafcf ("media: venus: core: correct maximum hardware
load for sdm845") meant to increase the maximum hardware load for sdm845,
but ended up changing the one for msm8996 instead.
Fixes: de5a0bafcf ("media: venus: core: correct maximum hardware load for sdm845")
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The header report return value from decoder sequence initialization is
available on CodaHx4 and CODA7541 already. Use the profile and level
identification values reported by the firmware to update codec specific
profile and level controls after sequence initialization has succeeded.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When a menu control is updated via s_ctrl, print the corresponding menu
entry string in addition to the numerical value it is set to.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Otherwise the default initialization would always swamp the debug log.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Print a single line containing the following information:
- which frame was decoded, including its type,
- if no frame was decoded, the reason (code) why
- which decoded frame was returned, copied out by either rotator or VODA,
- if no frame was returned, the reason (code) why, and
- the output queue sequence number, which is only useful in case
each queued coded buffer corresponds to exactly one frame.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a function to translate from V4L2 buffer flags to 'I'/'P'/'B'
characters for debug output.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This allows to use coda_debug level 2 for verbose but not quite as
verbose debug logging. Register access level logging is of limited
use anyway, as this includes busy polling of status bits.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case the sensor refuses to set the format, avoid printing the error
message that no compatible format was found.
This means that the try_fmt will be less verbose.
The error will be printed only if really a format cannot be found.
Some application try all possible formats in a row (gstreamer e.g.)
which will flood the console with error messages until a working one is found.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds support for the 'button' control DO_WHITE_BALANCE
This feature will enable the ISC to compute the white balance coefficients
in a one time shot, at the user discretion.
This can be used if a color chart/grey chart is present in front of the camera.
The ISC will adjust the coefficients and have them fixed until next balance
or until sensor mode is changed.
This is particularly useful for white balance adjustment in different
lighting scenarios, and then taking photos to similar scenery.
The old auto white balance stays in place, where the ISC will adjust every
4 frames to the current scenery lighting, if the scenery is approximately
grey in average, otherwise grey world algorithm fails.
One time white balance adjustments needs streaming to be enabled, such that
capture is enabled and the histogram has data to work with.
Histogram without capture does not work in this hardware module.
To start the one time white balance procedure:
v4l2-ctl --set-ctrl=do_white_balance=1
This feature works only if the sensor is streaming RAW data, as the hardware
supports a histogram only for RAW bayer components.
If the auto white balance is enabled, do_white_balance does nothing.
If the streaming is disabled, or the sensor does not output RAW data, the
control is inactive.
User controls now include the do_white_balance ctrl:
User Controls
brightness 0x00980900 (int) : min=-1024 max=1023 step=1 default=0 value=0 flags=slider
contrast 0x00980901 (int) : min=-2048 max=2047 step=1 default=256 value=256 flags=slider
white_balance_automatic 0x0098090c (bool) : default=1 value=0
do_white_balance 0x0098090d (button) : flags=write-only, execute-on-write
gamma 0x00980910 (int) : min=0 max=2 step=1 default=2 value=2 flags=slider
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Control DO_WHITE_BALANCE is a button, with read only and execute-on-write flags.
Adding this control in the proper list in the fill function.
After adding it here, we can see output of v4l2-ctl -L
do_white_balance 0x0098090d (button) : flags=write-only, execute-on-write
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reworked auto white balance feature (awb) to cope with all four channels.
Implemented stretching and grey world algorithms.
Using the histogram, the ISC will auto adjust the white balance during
frame captures.
Because each histogram needs a frame, it will take 4 frames for one adjustment.
When the gains were updated by previous code, the registers for the gains
were updated only on new streaming start. Now, after each full histogram the
registers are updated with new gains.
Also, on previous code, if the streaming stopped but not all 3 histograms
finished, a new histogram was started either way. This used to lead to an
error "timeout to update profile" when streaming was stopped.
According to the hardware, histogram can only work together with the capture,
not independently.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
- Build errors wrt. xattrs
- Mismerge which lead to a wrong Kconfig ifdef
- Missing endianness conversion
-----BEGIN PGP SIGNATURE-----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=0wS1
-----END PGP SIGNATURE-----
Merge tag 'upstream-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBIFS fixes from Richard Weinberger:
- build errors wrt xattrs
- mismerge which lead to a wrong Kconfig ifdef
- missing endianness conversion
* tag 'upstream-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubifs: Convert xattr inum to host order
ubifs: Use correct config name for encryption
ubifs: Fix build error without CONFIG_UBIFS_FS_XATTR
Merge yet more updates from Andrew Morton:
"A few final bits:
- large changes to vmalloc, yielding large performance benefits
- tweak the console-flush-on-panic code
- a few fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
panic: add an option to replay all the printk message in buffer
initramfs: don't free a non-existent initrd
fs/writeback.c: use rcu_barrier() to wait for inflight wb switches going into workqueue when umount
mm/compaction.c: correct zone boundary handling when isolating pages from a pageblock
mm/vmap: add DEBUG_AUGMENT_LOWEST_MATCH_CHECK macro
mm/vmap: add DEBUG_AUGMENT_PROPAGATE_CHECK macro
mm/vmalloc.c: keep track of free blocks for vmap allocation
- remove unneeded use of cc-option, cc-disable-warning, cc-ldoption
- exclude tracked files from .gitignore
- re-enable -Wint-in-bool-context warning
- refactor samples/Makefile
- stop building immediately if syncconfig fails
- do not sprinkle error messages when $(CC) does not exist
- move arch/alpha/defconfig to the configs subdirectory
- remove crappy header search path manipulation
- add comment lines to .config to clarify the end of menu blocks
- check uniqueness of module names (adding new warnings intentionally)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=oDeB
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- remove unneeded use of cc-option, cc-disable-warning, cc-ldoption
- exclude tracked files from .gitignore
- re-enable -Wint-in-bool-context warning
- refactor samples/Makefile
- stop building immediately if syncconfig fails
- do not sprinkle error messages when $(CC) does not exist
- move arch/alpha/defconfig to the configs subdirectory
- remove crappy header search path manipulation
- add comment lines to .config to clarify the end of menu blocks
- check uniqueness of module names (adding new warnings intentionally)
* tag 'kbuild-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (24 commits)
kconfig: use 'else ifneq' for Makefile to improve readability
kbuild: check uniqueness of module names
kconfig: Terminate menu blocks with a comment in the generated config
kbuild: add LICENSES to KBUILD_ALLDIRS
kbuild: remove 'addtree' and 'flags' magic for header search paths
treewide: prefix header search paths with $(srctree)/
media: prefix header search paths with $(srctree)/
media: remove unneeded header search paths
alpha: move arch/alpha/defconfig to arch/alpha/configs/defconfig
kbuild: terminate Kconfig when $(CC) or $(LD) is missing
kbuild: turn auto.conf.cmd into a mandatory include file
.gitignore: exclude .get_maintainer.ignore and .gitattributes
kbuild: add all Clang-specific flags unconditionally
kbuild: Don't try to add '-fcatch-undefined-behavior' flag
kbuild: add some extra warning flags unconditionally
kbuild: add -Wvla flag unconditionally
arch: remove dangling asm-generic wrappers
samples: guard sub-directories with CONFIG options
kbuild: re-enable int-in-bool-context warning
MAINTAINERS: kbuild: Add pattern for scripts/*vmlinux*
...
Pull i2c updates from Wolfram Sang:
"Some I2C core API additions which are kind of simple but enhance error
checking for users a lot, especially by returning errno now.
There are wrappers to still support the old API but it will be removed
once all users are converted"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: add device-managed version of i2c_new_dummy
i2c: core: improve return value handling of i2c_new_device and i2c_new_dummy
Unicode 12.1.0.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAlzg2qIACgkQ8vlZVpUN
gaPYfgf+IadtbeBYbKcHQzw8OZ9UxyGv7+Havs523XzhdceiflpOCe3lpSFYuX6w
0CtRIWEOqFzQLRHUlX/sRywYLvrvg3irDuYJGTzny9MfPEI+tVCkYi877PPAOOR3
4xay7dF63mcCpmhRxgw1fLx5I/hYpzrDnw5dGe7jjgU6SrR5FpE2GmEmbfBW087W
zAuRDkuTv03J791Kgpq4TAMNla9F2/oedq/2B0v43+TnKfYe1SEIDm3VusUvSfoI
++8CfRrRJ3D7vCmtFSuieFFb91HtHMqdv0gaad2cY1DfvJLVm7gP1uPL7QahA5Dq
VfhvFfqshqN9Jizr6BqP5GPOj2J9cw==
=QK+R
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Some bug fixes, and an update to the URL's for the final version of
Unicode 12.1.0"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: avoid panic during forced reboot due to aborted journal
ext4: fix block validity checks for journal inodes using indirect blocks
unicode: update to Unicode 12.1.0 final
unicode: add missing check for an error return from utf8lookup()
ext4: fix miscellaneous sparse warnings
ext4: unsigned int compared against zero
ext4: fix use-after-free in dx_release()
ext4: fix data corruption caused by overlapping unaligned and aligned IO
jbd2: fix potential double free
ext4: zero out the unused memory region in the extent tree block
-----BEGIN PGP SIGNATURE-----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=JhcA
-----END PGP SIGNATURE-----
Merge tag '5.2-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Minor cleanup and fixes, one for stable, four rdma (smbdirect)
related. Also adds SEEK_HOLE support"
* tag '5.2-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: add support for SEEK_DATA and SEEK_HOLE
Fixed https://bugzilla.kernel.org/show_bug.cgi?id=202935 allow write on the same file
cifs: Allocate memory for all iovs in smb2_ioctl
cifs: Don't match port on SMBDirect transport
cifs:smbd Use the correct DMA direction when sending data
cifs:smbd When reconnecting to server, call smbd_destroy() after all MIDs have been called
cifs: use the right include for signal_pending()
smb3: trivial cleanup to smb2ops.c
cifs: cleanup smb2ops.c and normalize strings
smb3: display session id in debug data
Pull perf tooling updates from Ingo Molnar:
"perf.data:
- Streaming compression of perf ring buffer into
PERF_RECORD_COMPRESSED user space records, resulting in ~3-5x
perf.data file size reduction on variety of tested workloads what
saves storage space on larger server systems where perf.data size
can easily reach several tens or even hundreds of GiBs, especially
when profiling with DWARF-based stacks and tracing of context
switches.
perf record:
- Improve -user-regs/intr-regs suggestions to overcome errors
perf annotate:
- Remove hist__account_cycles() from callback, speeding up branch
processing (perf record -b)
perf stat:
- Add a 'percore' event qualifier, e.g.: -e
cpu/event=0,umask=0x3,percore=1/, that sums up the event counts for
both hardware threads in a core.
We can already do this with --per-core, but it's often useful to do
this together with other metrics that are collected per hardware
thread.
I.e. now its possible to do this per-event, and have it mixed with
other events not aggregated by core.
arm64:
- Map Brahma-B53 CPUID to cortex-a53 events.
- Add Cortex-A57 and Cortex-A72 events.
csky:
- Add DWARF register mappings for libdw, allowing --call-graph=dwarf
to work on the C-SKY arch.
x86:
- Add support for recording and printing XMM registers, available,
for instance, on Icelake.
- Add uncore_upi (Intel's "Ultra Path Interconnect" events) JSON
support. UPI replaced the Intel QuickPath Interconnect (QPI) in
Xeon Skylake-SP.
Intel PT:
- Fix instructions sampling rate.
- Timestamp fixes.
- Improve exported-sql-viewer GUI, allowing, for instance, to
copy'n'paste the trees, useful for e-mailing"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (73 commits)
perf stat: Support 'percore' event qualifier
perf stat: Factor out aggregate counts printing
perf tools: Add a 'percore' event qualifier
perf docs: Add description for stderr
perf intel-pt: Fix sample timestamp wrt non-taken branches
perf intel-pt: Fix improved sample timestamp
perf intel-pt: Fix instructions sampling rate
perf regs x86: Add X86 specific arch__intr_reg_mask()
perf parse-regs: Add generic support for arch__intr/user_reg_mask()
perf parse-regs: Split parse_regs
perf vendor events arm64: Add Cortex-A57 and Cortex-A72 events
perf vendor events arm64: Map Brahma-B53 CPUID to cortex-a53 events
perf vendor events arm64: Remove [[:xdigit:]] wildcard
perf jevents: Remove unused variable
perf test zstd: Fixup verbose mode output
perf tests: Implement Zstd comp/decomp integration test
perf inject: Enable COMPRESSED record decompression
perf report: Implement perf.data record decompression
perf record: Implement -z,--compression_level[=<n>] option
perf report: Add stub processing of compressed events for -D
...
Pull clocksource updates from Ingo Molnar:
"Misc clocksource/clockevent driver updates that came in a bit late but
are ready for v5.2"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
misc: atmel_tclib: Do not probe already used TCBs
clocksource/drivers/timer-atmel-tcb: Convert tc_clksrc_suspend|resume() to static
clocksource/drivers/tcb_clksrc: Rename the file for consistency
clocksource/drivers/timer-atmel-pit: Rework Kconfig option
clocksource/drivers/tcb_clksrc: Move Kconfig option
ARM: at91: Implement clocksource selection
clocksource/drivers/tcb_clksrc: Use tcb as sched_clock
clocksource/drivers/tcb_clksrc: Stop depending on atmel_tclib
ARM: at91: move SoC specific definitions to SoC folder
clocksource/drivers/timer-milbeaut: Cleanup common register accesses
clocksource/drivers/timer-milbeaut: Add shutdown function
clocksource/drivers/timer-milbeaut: Fix to enable one-shot timer
clocksource/drivers/tegra: Rework for compensation of suspend time
clocksource/drivers/sp804: Add COMPILE_TEST to CONFIG_ARM_TIMER_SP804
clocksource/drivers/sun4i: Add a compatible for suniv
dt-bindings: timer: Add Allwinner suniv timer
Pull IRQ chip updates from Ingo Molnar:
"A late irqchips update:
- New TI INTR/INTA set of drivers
- Rewrite of the stm32mp1-exti driver as a platform driver
- Update the IOMMU MSI mapping API to be RT friendly
- A number of cleanups and other low impact fixes"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
iommu/dma-iommu: Remove iommu_dma_map_msi_msg()
irqchip/gic-v3-mbi: Don't map the MSI page in mbi_compose_m{b, s}i_msg()
irqchip/ls-scfg-msi: Don't map the MSI page in ls_scfg_msi_compose_msg()
irqchip/gic-v3-its: Don't map the MSI page in its_irq_compose_msi_msg()
irqchip/gicv2m: Don't map the MSI page in gicv2m_compose_msi_msg()
iommu/dma-iommu: Split iommu_dma_map_msi_msg() in two parts
genirq/msi: Add a new field in msi_desc to store an IOMMU cookie
arm64: arch_k3: Enable interrupt controller drivers
irqchip/ti-sci-inta: Add msi domain support
soc: ti: Add MSI domain bus support for Interrupt Aggregator
irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver
dt-bindings: irqchip: Introduce TISCI Interrupt Aggregator bindings
irqchip/ti-sci-intr: Add support for Interrupt Router driver
dt-bindings: irqchip: Introduce TISCI Interrupt router bindings
gpio: thunderx: Use the default parent apis for {request,release}_resources
genirq: Introduce irq_chip_{request,release}_resource_parent() apis
firmware: ti_sci: Add helper apis to manage resources
firmware: ti_sci: Add RM mapping table for am654
firmware: ti_sci: Add support for IRQ management
firmware: ti_sci: Add support for RM core ops
...
Lubomir Rintel
Sakari Ailus
Akinobu Mita
Hans Verkuil
Hans Verkuil
Neil Armstrong
Stefan Brüns
Sean Young
Oliver Neukum
Daniel Gomez
Brad Love
Stanimir Varbanov
Kelvin Lawson
Alexandre Courbot
Philipp Zabel
Eugen Hristev
Linus Torvalds