Depending on the size of the area to be memset'ed, the nios2 memset implementation
either uses a naive loop (for buffers smaller or equal than 8 bytes) or a more optimized
implementation (for buffers larger than 8 bytes). This implementation does 4-byte stores
rather than 1-byte stores to speed up memset.
However, we discovered that on our nios2 platform, memset() was not properly setting the
buffer to the expected value. A memset of 0xff would not set the entire buffer to 0xff, but to:
0xff 0x00 0xff 0x00 0xff 0x00 0xff 0x00 ...
Which is obviously incorrect. Our investigation has revealed that the problem lies in the
incorrect constraints used in the inline assembly.
The following piece of assembly, from the nios2 memset implementation, is supposed to
create a 4-byte value that repeats 4 times the 1-byte pattern passed as memset argument:
/* fill8 %3, %5 (c & 0xff) */
" slli %4, %5, 8\n"
" or %4, %4, %5\n"
" slli %3, %4, 16\n"
" or %3, %3, %4\n"
However, depending on the compiler and optimization level, this code might be compiled as:
34: 280a923a slli r5,r5,8
38: 294ab03a or r5,r5,r5
3c: 2808943a slli r4,r5,16
40: 2148b03a or r4,r4,r5
This is wrong because r5 gets used both for %5 and %4, which leads to the final pattern
stored in r4 to be 0xff00ff00 rather than the expected 0xffffffff.
%4 is defined with the "=r" constraint, i.e as an output operand. However, as explained in
http://www.ethernut.de/en/documents/arm-inline-asm.html, this does not prevent gcc from
using the same register for an output operand (%4) and input operand (%5). By using the
constraint modifier '&', we indicate that the register should be used for output only. With this
change, we get the following assembly output:
34: 2810923a slli r8,r5,8
38: 4150b03a or r8,r8,r5
3c: 400e943a slli r7,r8,16
40: 3a0eb03a or r7,r7,r8
Which correctly produces the 0xffffffff pattern when 0xff is passed as the memset() pattern.
It is worth mentioning the observed consequence of this bug: we were hitting the kernel
BUG() in mm/bootmem.c:__free() that verifies when marking a page as free that it was
previously marked as occupied (i.e that the bit was set to 1). The entire bootmem bitmap is
set to 0xff bit via a memset() during the bootmem initialization. The bootmem_free() call right
after the initialization was finding some bits to be set to 0, which didn't make sense since the
bitmap has just been memset'ed to 0xff. Except that due to the bug explained above, the
bitmap was in fact initialized to 0xff00ff00.
Thanks to Marek Vasut for his help and feedback.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Ley Foon Tan <lftan@altera.com>
nios2 builds fail with the following build error.
arch/nios2/kernel/prom.c: In function 'early_init_dt_scan_serial':
arch/nios2/kernel/prom.c💯2: error:
implicit declaration of function 'fdt_translate_address'
Commit c90fe9c039 ("of: earlycon: Move address translation to
of_setup_earlycon()") replaced fdt_translate_address() with
of_flat_dt_translate_address() but missed updating the nios2 code.
Fixes: c90fe9c039 ("of: earlycon: Move address translation to of_setup_earlycon()")
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Ley Foon Tan <lftan@altera.com>
KASAN needs to know whether the allocation happens in an IRQ handler.
This lets us strip everything below the IRQ entry point to reduce the
number of unique stack traces needed to be stored.
Move the definition of __irq_entry to <linux/interrupt.h> so that the
users don't need to pull in <linux/ftrace.h>. Also introduce the
__softirq_entry macro which is similar to __irq_entry, but puts the
corresponding functions to the .softirqentry.text section.
Signed-off-by: Alexander Potapenko <glider@google.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Andrey Konovalov <adech.fo@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Konstantin Serebryany <kcc@google.com>
Cc: Dmitry Chernenkov <dmitryc@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch updates all instances of csum_tcpudp_magic and
csum_tcpudp_nofold to reflect the types that are usually used as the source
inputs. For example the protocol field is populated based on nexthdr which
is actually an unsigned 8 bit value. The length is usually populated based
on skb->len which is an unsigned integer.
This addresses an issue in which the IPv6 function csum_ipv6_magic was
generating a checksum using the full 32b of skb->len while
csum_tcpudp_magic was only using the lower 16 bits. As a result we could
run into issues when attempting to adjust the checksum as there was no
protocol agnostic way to update it.
With this change the value is still truncated as many architectures use
"(len + proto) << 8", however this truncation only occurs for values
greater than 16776960 in length and as such is unlikely to occur as we stop
the inner headers at ~64K in size.
I did have to make a few minor changes in the arm, mn10300, nios2, and
score versions of the function in order to support these changes as they
were either using things such as an OR to combine the protocol and length,
or were using ntohs to convert the length which would have truncated the
value.
I also updated a few spots in terms of whitespace and type differences for
the addresses. Most of this was just to make sure all of the definitions
were in sync going forward.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the generic implementation to <linux/dma-mapping.h> now that all
architectures support it and remove the HAVE_DMA_ATTR Kconfig symbol now
that everyone supports them.
[valentinrothberg@gmail.com: remove leftovers in Kconfig]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__HAVE_ARCH_MEMMOVE and __HAVE_ARCH_MEMSET are unconditionally defined
for nios2, so there is no need to protect the function definitions of
memmove() and memset().
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Ley Foon Tan <lftan@altera.com>
The generic __xchg() implementation present in asm-generic/cmpxchg.h is
correct on nios2 and even generates the same code. Switch to this generic
implementation to trim down the amount of ad-hoc copies of the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Ley Foon Tan <lftan@altera.com>
Fix the following compiler splat by adding __maybe_unused annotation to
the variable. Using this particular annotation has the least ugly impact
on the code compared to using ifdeffery.
arch/nios2/kernel/setup.c: In function 'nios2_boot_init':
arch/nios2/kernel/setup.c:107:7: warning: unused variable 'cmdline_passed' [-Wunused-variable]
char cmdline_passed[COMMAND_LINE_SIZE] = { 0, };
^
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Ley Foon Tan <lftan@altera.com>
Pull strscpy string copy function implementation from Chris Metcalf.
Chris sent this during the merge window, but I waffled back and forth on
the pull request, which is why it's going in only now.
The new "strscpy()" function is definitely easier to use and more secure
than either strncpy() or strlcpy(), both of which are horrible nasty
interfaces that have serious and irredeemable problems.
strncpy() has a useless return value, and doesn't NUL-terminate an
overlong result. To make matters worse, it pads a short result with
zeroes, which is a performance disaster if you have big buffers.
strlcpy(), by contrast, is a mis-designed "fix" for strlcpy(), lacking
the insane NUL padding, but having a differently broken return value
which returns the original length of the source string. Which means
that it will read characters past the count from the source buffer, and
you have to trust the source to be properly terminated. It also makes
error handling fragile, since the test for overflow is unnecessarily
subtle.
strscpy() avoids both these problems, guaranteeing the NUL termination
(but not excessive padding) if the destination size wasn't zero, and
making the overflow condition very obvious by returning -E2BIG. It also
doesn't read past the size of the source, and can thus be used for
untrusted source data too.
So why did I waffle about this for so long?
Every time we introduce a new-and-improved interface, people start doing
these interminable series of trivial conversion patches.
And every time that happens, somebody does some silly mistake, and the
conversion patch to the improved interface actually makes things worse.
Because the patch is mindnumbing and trivial, nobody has the attention
span to look at it carefully, and it's usually done over large swatches
of source code which means that not every conversion gets tested.
So I'm pulling the strscpy() support because it *is* a better interface.
But I will refuse to pull mindless conversion patches. Use this in
places where it makes sense, but don't do trivial patches to fix things
that aren't actually known to be broken.
* 'strscpy' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: use global strscpy() rather than private copy
string: provide strscpy()
Make asm/word-at-a-time.h available on all architectures
Seeing the 'of' characters in a symbol that is being called from
ACPI seems to freak out people. So let's do a bit of pointless
renaming so that these folks do feel at home.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Max10 is a FPGA device. This patch adds defconfig based on Max10 hardware
reference design. Design is intended to run on Max10 development kit.
Signed-off-by: Chee Nouk Phoon <cnphoon@altera.com>
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Max10 is a FPGA device. This patch adds Nios2 support for Max10.
This device tree is based on Max10 hardware reference design.
Signed-off-by: Chee Nouk Phoon <cnphoon@altera.com>
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Removed some statistic counters to improve the performance of the handler.
Signed-off-by: Bernd Weiberg <bernd.weiberg@siemens.com>
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Migrate nios2 driver to the new 'set-state' interface provided by clockevents core, the earlier 'set-mode' interface is marked obsolete now.
This also enables us to implement callbacks for new states of clockevent devices, for example: ONESHOT_STOPPED.
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Dmitry Torokhov <dtor@chromium.org>
Cc: nios2-dev@lists.rocketboards.org
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ley Foon Tan <lftan@altera.com>
Commit 2ae416b142 ("mm: new mm hook framework") introduced an empty
header file (mm-arch-hooks.h) for every architecture, even those which
doesn't need to define mm hooks.
As suggested by Geert Uytterhoeven, this could be cleaned through the use
of a generic header file included via each per architecture
asm/include/Kbuild file.
The PowerPC architecture is not impacted here since this architecture has
to defined the arch_remap MM hook.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added the x86 implementation of word-at-a-time to the
generic version, which previously only supported big-endian.
Omitted the x86-specific load_unaligned_zeropad(), which in
any case is also not present for the existing BE-only
implementation of a word-at-a-time, and is only used under
CONFIG_DCACHE_WORD_ACCESS.
Added as a "generic-y" to the Kbuilds of all architectures
that didn't previously have it.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Pull asm/scatterlist.h removal from Jens Axboe:
"We don't have any specific arch scatterlist anymore, since parisc
finally switched over. Kill the include"
* 'for-4.2/sg' of git://git.kernel.dk/linux-block:
remove scatterlist.h generation from arch Kbuild files
remove <asm/scatterlist.h>
CRIU is recreating the process memory layout by remapping the checkpointee
memory area on top of the current process (criu). This includes remapping
the vDSO to the place it has at checkpoint time.
However some architectures like powerpc are keeping a reference to the
vDSO base address to build the signal return stack frame by calling the
vDSO sigreturn service. So once the vDSO has been moved, this reference
is no more valid and the signal frame built later are not usable.
This patch serie is introducing a new mm hook framework, and a new
arch_remap hook which is called when mremap is done and the mm lock still
hold. The next patch is adding the vDSO remap and unmap tracking to the
powerpc architecture.
This patch (of 3):
This patch introduces a new set of header file to manage mm hooks:
- per architecture empty header file (arch/x/include/asm/mm-arch-hooks.h)
- a generic header (include/linux/mm-arch-hooks.h)
The architecture which need to overwrite a hook as to redefine it in its
header file, while architecture which doesn't need have nothing to do.
The default hooks are defined in the generic header and are used in the
case the architecture is not defining it.
In a next step, mm hooks defined in include/asm-generic/mm_hooks.h should
be moved here.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull crypto update from Herbert Xu:
"Here is the crypto update for 4.2:
API:
- Convert RNG interface to new style.
- New AEAD interface with one SG list for AD and plain/cipher text.
All external AEAD users have been converted.
- New asymmetric key interface (akcipher).
Algorithms:
- Chacha20, Poly1305 and RFC7539 support.
- New RSA implementation.
- Jitter RNG.
- DRBG is now seeded with both /dev/random and Jitter RNG. If kernel
pool isn't ready then DRBG will be reseeded when it is.
- DRBG is now the default crypto API RNG, replacing krng.
- 842 compression (previously part of powerpc nx driver).
Drivers:
- Accelerated SHA-512 for arm64.
- New Marvell CESA driver that supports DMA and more algorithms.
- Updated powerpc nx 842 support.
- Added support for SEC1 hardware to talitos"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (292 commits)
crypto: marvell/cesa - remove COMPILE_TEST dependency
crypto: algif_aead - Temporarily disable all AEAD algorithms
crypto: af_alg - Forbid the use internal algorithms
crypto: echainiv - Only hold RNG during initialisation
crypto: seqiv - Add compatibility support without RNG
crypto: eseqiv - Offer normal cipher functionality without RNG
crypto: chainiv - Offer normal cipher functionality without RNG
crypto: user - Add CRYPTO_MSG_DELRNG
crypto: user - Move cryptouser.h to uapi
crypto: rng - Do not free default RNG when it becomes unused
crypto: skcipher - Allow givencrypt to be NULL
crypto: sahara - propagate the error on clk_disable_unprepare() failure
crypto: rsa - fix invalid select for AKCIPHER
crypto: picoxcell - Update to the current clk API
crypto: nx - Check for bogus firmware properties
crypto: marvell/cesa - add DT bindings documentation
crypto: marvell/cesa - add support for Kirkwood and Dove SoCs
crypto: marvell/cesa - add support for Orion SoCs
crypto: marvell/cesa - add allhwsupport module parameter
crypto: marvell/cesa - add support for all armada SoCs
...
Pull x86 core updates from Ingo Molnar:
"There were so many changes in the x86/asm, x86/apic and x86/mm topics
in this cycle that the topical separation of -tip broke down somewhat -
so the result is a more traditional architecture pull request,
collected into the 'x86/core' topic.
The topics were still maintained separately as far as possible, so
bisectability and conceptual separation should still be pretty good -
but there were a handful of merge points to avoid excessive
dependencies (and conflicts) that would have been poorly tested in the
end.
The next cycle will hopefully be much more quiet (or at least will
have fewer dependencies).
The main changes in this cycle were:
* x86/apic changes, with related IRQ core changes: (Jiang Liu, Thomas
Gleixner)
- This is the second and most intrusive part of changes to the x86
interrupt handling - full conversion to hierarchical interrupt
domains:
[IOAPIC domain] -----
|
[MSI domain] --------[Remapping domain] ----- [ Vector domain ]
| (optional) |
[HPET MSI domain] ----- |
|
[DMAR domain] -----------------------------
|
[Legacy domain] -----------------------------
This now reflects the actual hardware and allowed us to distangle
the domain specific code from the underlying parent domain, which
can be optional in the case of interrupt remapping. It's a clear
separation of functionality and removes quite some duct tape
constructs which plugged the remap code between ioapic/msi/hpet
and the vector management.
- Intel IOMMU IRQ remapping enhancements, to allow direct interrupt
injection into guests (Feng Wu)
* x86/asm changes:
- Tons of cleanups and small speedups, micro-optimizations. This
is in preparation to move a good chunk of the low level entry
code from assembly to C code (Denys Vlasenko, Andy Lutomirski,
Brian Gerst)
- Moved all system entry related code to a new home under
arch/x86/entry/ (Ingo Molnar)
- Removal of the fragile and ugly CFI dwarf debuginfo annotations.
Conversion to C will reintroduce many of them - but meanwhile
they are only getting in the way, and the upstream kernel does
not rely on them (Ingo Molnar)
- NOP handling refinements. (Borislav Petkov)
* x86/mm changes:
- Big PAT and MTRR rework: making the code more robust and
preparing to phase out exposing direct MTRR interfaces to drivers -
in favor of using PAT driven interfaces (Toshi Kani, Luis R
Rodriguez, Borislav Petkov)
- New ioremap_wt()/set_memory_wt() interfaces to support
Write-Through cached memory mappings. This is especially
important for good performance on NVDIMM hardware (Toshi Kani)
* x86/ras changes:
- Add support for deferred errors on AMD (Aravind Gopalakrishnan)
This is an important RAS feature which adds hardware support for
poisoned data. That means roughly that the hardware marks data
which it has detected as corrupted but wasn't able to correct, as
poisoned data and raises an APIC interrupt to signal that in the
form of a deferred error. It is the OS's responsibility then to
take proper recovery action and thus prolonge system lifetime as
far as possible.
- Add support for Intel "Local MCE"s: upcoming CPUs will support
CPU-local MCE interrupts, as opposed to the traditional system-
wide broadcasted MCE interrupts (Ashok Raj)
- Misc cleanups (Borislav Petkov)
* x86/platform changes:
- Intel Atom SoC updates
... and lots of other cleanups, fixlets and other changes - see the
shortlog and the Git log for details"
* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (222 commits)
x86/hpet: Use proper hpet device number for MSI allocation
x86/hpet: Check for irq==0 when allocating hpet MSI interrupts
x86/mm/pat, drivers/infiniband/ipath: Use arch_phys_wc_add() and require PAT disabled
x86/mm/pat, drivers/media/ivtv: Use arch_phys_wc_add() and require PAT disabled
x86/platform/intel/baytrail: Add comments about why we disabled HPET on Baytrail
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
iommu, x86: Properly handle posted interrupts for IOMMU hotplug
iommu, x86: Provide irq_remapping_cap() interface
iommu, x86: Setup Posted-Interrupts capability for Intel iommu
iommu, x86: Add cap_pi_support() to detect VT-d PI capability
iommu, x86: Avoid migrating VT-d posted interrupts
iommu, x86: Save the mode (posted or remapped) of an IRTE
iommu, x86: Implement irq_set_vcpu_affinity for intel_ir_chip
iommu: dmar: Provide helper to copy shared irte fields
iommu: dmar: Extend struct irte for VT-d Posted-Interrupts
iommu: Add new member capability to struct irq_remap_ops
x86/asm/entry/64: Disentangle error_entry/exit gsbase/ebx/usermode code
x86/asm/entry/32: Shorten __audit_syscall_entry() args preparation
x86/asm/entry/32: Explain reloading of registers after __audit_syscall_entry()
...
Merge the mvebu/drivers branch of the arm-soc tree which contains
just a single patch bfa1ce5f38 ("bus:
mvebu-mbus: add mv_mbus_dram_info_nooverlap()") that happens to be
a prerequisite of the new marvell/cesa crypto driver.
nios2 is the only architecture that does not inline get_cycles
and does not export it. This breaks crypto as it uses get_cycles
in a number of modules.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add ioremap_wt() to all arch-specific asm/io.h headers which
define ioremap_wc() locally. These headers do not include
<asm-generic/iomap.h>. Some of them include <asm-generic/io.h>,
but ioremap_wt() is defined for consistency since they define
all ioremap_xxx locally.
In all architectures without Write-Through support, ioremap_wt()
is defined indentical to ioremap_nocache().
frv and m68k already have ioremap_writethrough(). On those we
add ioremap_wt() indetical to ioremap_writethrough() and defines
ARCH_HAS_IOREMAP_WT in both architectures.
The ioremap_wt() interface is exported to drivers.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Elliott@hp.com
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: arnd@arndb.de
Cc: hch@lst.de
Cc: hmh@hmh.eng.br
Cc: jgross@suse.com
Cc: konrad.wilk@oracle.com
Cc: linux-mm <linux-mm@kvack.org>
Cc: linux-nvdimm@lists.01.org
Cc: stefan.bader@canonical.com
Cc: yigal@plexistor.com
Link: http://lkml.kernel.org/r/1433436928-31903-9-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Introduce faulthandler_disabled() and use it to check for irq context and
disabled pagefaults (via pagefault_disable()) in the pagefault handlers.
Please note that we keep the in_atomic() checks in place - to detect
whether in irq context (in which case preemption is always properly
disabled).
In contrast, preempt_disable() should never be used to disable pagefaults.
With !CONFIG_PREEMPT_COUNT, preempt_disable() doesn't modify the preempt
counter, and therefore the result of in_atomic() differs.
We validate that condition by using might_fault() checks when calling
might_sleep().
Therefore, add a comment to faulthandler_disabled(), describing why this
is needed.
faulthandler_disabled() and pagefault_disable() are defined in
linux/uaccess.h, so let's properly add that include to all relevant files.
This patch is based on a patch from Thomas Gleixner.
Reviewed-and-tested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: David.Laight@ACULAB.COM
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: airlied@linux.ie
Cc: akpm@linux-foundation.org
Cc: benh@kernel.crashing.org
Cc: bigeasy@linutronix.de
Cc: borntraeger@de.ibm.com
Cc: daniel.vetter@intel.com
Cc: heiko.carstens@de.ibm.com
Cc: herbert@gondor.apana.org.au
Cc: hocko@suse.cz
Cc: hughd@google.com
Cc: mst@redhat.com
Cc: paulus@samba.org
Cc: ralf@linux-mips.org
Cc: schwidefsky@de.ibm.com
Cc: yang.shi@windriver.com
Link: http://lkml.kernel.org/r/1431359540-32227-7-git-send-email-dahi@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reported by the header checker (CONFIG_HEADERS_CHECK=y):
CHECK usr/include/asm/ (31 files)
./usr/include/asm/ptrace.h:77: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Ley Foon Tan <lftan@altera.com>
Remove the end address checking for initda function. We need to invalidate
each address line for initda instruction, from start to end address.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Merge second patchbomb from Andrew Morton:
- the rest of MM
- various misc bits
- add ability to run /sbin/reboot at reboot time
- printk/vsprintf changes
- fiddle with seq_printf() return value
* akpm: (114 commits)
parisc: remove use of seq_printf return value
lru_cache: remove use of seq_printf return value
tracing: remove use of seq_printf return value
cgroup: remove use of seq_printf return value
proc: remove use of seq_printf return value
s390: remove use of seq_printf return value
cris fasttimer: remove use of seq_printf return value
cris: remove use of seq_printf return value
openrisc: remove use of seq_printf return value
ARM: plat-pxa: remove use of seq_printf return value
nios2: cpuinfo: remove use of seq_printf return value
microblaze: mb: remove use of seq_printf return value
ipc: remove use of seq_printf return value
rtc: remove use of seq_printf return value
power: wakeup: remove use of seq_printf return value
x86: mtrr: if: remove use of seq_printf return value
linux/bitmap.h: improve BITMAP_{LAST,FIRST}_WORD_MASK
MAINTAINERS: CREDITS: remove Stefano Brivio from B43
.mailmap: add Ricardo Ribalda
CREDITS: add Ricardo Ribalda Delgado
...
The seq_printf return value, because it's frequently misused,
will eventually be converted to void.
See: commit 1f33c41c03 ("seq_file: Rename seq_overflow() to
seq_has_overflowed() and make public")
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull exec domain removal from Richard Weinberger:
"This series removes execution domain support from Linux.
The idea behind exec domains was to support different ABIs. The
feature was never complete nor stable. Let's rip it out and make the
kernel signal handling code less complicated"
* 'exec_domain_rip_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/misc: (27 commits)
arm64: Removed unused variable
sparc: Fix execution domain removal
Remove rest of exec domains.
arch: Remove exec_domain from remaining archs
arc: Remove signal translation and exec_domain
xtensa: Remove signal translation and exec_domain
xtensa: Autogenerate offsets in struct thread_info
x86: Remove signal translation and exec_domain
unicore32: Remove signal translation and exec_domain
um: Remove signal translation and exec_domain
tile: Remove signal translation and exec_domain
sparc: Remove signal translation and exec_domain
sh: Remove signal translation and exec_domain
s390: Remove signal translation and exec_domain
mn10300: Remove signal translation and exec_domain
microblaze: Remove signal translation and exec_domain
m68k: Remove signal translation and exec_domain
m32r: Remove signal translation and exec_domain
m32r: Autogenerate offsets in struct thread_info
frv: Remove signal translation and exec_domain
...
Pull vfs update from Al Viro:
"Part one:
- struct filename-related cleanups
- saner iov_iter_init() replacements (and switching the syscalls to
use of those)
- ntfs switch to ->write_iter() (Anton)
- aio cleanups and splitting iocb into common and async parts
(Christoph)
- assorted fixes (me, bfields, Andrew Elble)
There's a lot more, including the completion of switchover to
->{read,write}_iter(), d_inode/d_backing_inode annotations, f_flags
race fixes, etc, but that goes after #for-davem merge. David has
pulled it, and once it's in I'll send the next vfs pull request"
* 'for-linus-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (35 commits)
sg_start_req(): use import_iovec()
sg_start_req(): make sure that there's not too many elements in iovec
blk_rq_map_user(): use import_single_range()
sg_io(): use import_iovec()
process_vm_access: switch to {compat_,}import_iovec()
switch keyctl_instantiate_key_common() to iov_iter
switch {compat_,}do_readv_writev() to {compat_,}import_iovec()
aio_setup_vectored_rw(): switch to {compat_,}import_iovec()
vmsplice_to_user(): switch to import_iovec()
kill aio_setup_single_vector()
aio: simplify arguments of aio_setup_..._rw()
aio: lift iov_iter_init() into aio_setup_..._rw()
lift iov_iter into {compat_,}do_readv_writev()
NFS: fix BUG() crash in notify_change() with patch to chown_common()
dcache: return -ESTALE not -EBUSY on distributed fs race
NTFS: Version 2.1.32 - Update file write from aio_write to write_iter.
VFS: Add iov_iter_fault_in_multipages_readable()
drop bogus check in file_open_root()
switch security_inode_getattr() to struct path *
constify tomoyo_realpath_from_path()
...
flush_old_exec() has already done that. Back on 2011 a bunch of
instances like that had been kicked out, but that hadn't taken
care of then-out-of-tree architectures, obviously, and they served
as reinfection vector...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Remove the end address checking for flushda function. We need to flush
each address line for flushda instruction, from start to end address.
This is because flushda instruction only flush the cache if tag and line
fields are matched.
Change to use ldwio instruction (bypass cache) to load the instruction
that causing trap. Our interest is the actual instruction that executed
by the processor, this should be uncached.
Note, EA address might be an userspace cached address.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Follow commit 871341023c.
Kernel faults are expected to handle OOM conditions gracefully (gup,
uaccess etc.), so they should never invoke the OOM killer. Reserve
this for faults triggered in user context when it is the only option.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Commit 92d5dd8cd6 ("nios2: update pt_regs") removed the nios2 specific
ucontext.h, replacing it with the version from asm-generic. Thus it's no
longer necessary to include ucontext.h in exported headers.
Cc: Chung-Ling Tang <cltang@codesourcery.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Ley Foon Tan <lftan@altera.com>
Remove struct pt_regs from user header and use generic ucontext.h.
Signed-off-by: Chung-Ling Tang <cltang@codesourcery.com>
Acked-by: Ley Foon Tan <lftan@altera.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.5 (GNU/Linux)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=u6dr
-----END PGP SIGNATURE-----
Merge tag 'nios2-v3.20-rc1' of git://git.rocketboards.org/linux-socfpga-next
Pull arch/nios2 update from Ley Foon Tan:
"Here is the nios2 update for 3.20:
- add early printk support
- add kgdb support
- add compressed kernel support
- bugfixes"
* tag 'nios2-v3.20-rc1' of git://git.rocketboards.org/linux-socfpga-next:
nios2: add kgdb support
MAINTAINERS: update arch/nios2 git tree
nios2: default CONFIG_NIOS2_BOOT_LINK_OFFSET to 8MB
nios2: Add support for compressed kernel
nios2: add early printk support
nios2: Port OOM changes to do_page_fault()
nios2: Remove unused prepare_to_copy()
Romain Perier
Guenter Roeck
Alexander Potapenko
Alexander Duyck
Christoph Hellwig
Ley Foon Tan
Linus Torvalds
Tobias Klauser
Marek Vasut
Rafael J. Wysocki
Marc Zyngier
Chee Nouk Phoon
Bernd Weiberg
Viresh Kumar
Laurent Dufour
Chris Metcalf
Herbert Xu
Toshi Kani
David Hildenbrand
Ezequiel Garcia
Joe Perches
Richard Weinberger
Al Viro
Chung-Ling Tang