/proc has been ignoring struct file_operations::owner field for 10 years.
Specifically, it started with commit 786d7e1612
("Fix rmmod/read/write races in /proc entries"). Notice the chunk where
inode->i_fop is initialized with proxy struct file_operations for
regular files:
- if (de->proc_fops)
- inode->i_fop = de->proc_fops;
+ if (de->proc_fops) {
+ if (S_ISREG(inode->i_mode))
+ inode->i_fop = &proc_reg_file_ops;
+ else
+ inode->i_fop = de->proc_fops;
+ }
VFS stopped pinning module at this point.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FACK loss detection has been disabled by default and the
successor RACK subsumed FACK and can handle reordering better.
This patch removes FACK to simplify TCP loss recovery.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 45f119bf93.
Eric Dumazet says:
We found at Google a significant regression caused by
45f119bf93 tcp: remove header prediction
In typical RPC (TCP_RR), when a TCP socket receives data, we now call
tcp_ack() while we used to not call it.
This touches enough cache lines to cause a slowdown.
so problem does not seem to be HP removal itself but the tcp_ack()
call. Therefore, it might be possible to remove HP after all, provided
one finds a way to elide tcp_ack for most cases.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
was used by tcp prequeue and header prediction.
TCPFORWARDRETRANS use was removed in january.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
DRAM supply shortage and poor memory pressure tracking in TCP
stack makes any change in SO_SNDBUF/SO_RCVBUF (or equivalent autotuning
limits) and tcp_mem[] quite hazardous.
TCPMemoryPressures SNMP counter is an indication of tcp_mem sysctl
limits being hit, but only tracking number of transitions.
If TCP stack behavior under stress was perfect :
1) It would maintain memory usage close to the limit.
2) Memory pressure state would be entered for short times.
We certainly prefer 100 events lasting 10ms compared to one event
lasting 200 seconds.
This patch adds a new SNMP counter tracking cumulative duration of
memory pressure events, given in ms units.
$ cat /proc/sys/net/ipv4/tcp_mem
3088 4117 6176
$ grep TCP /proc/net/sockstat
TCP: inuse 180 orphan 0 tw 2 alloc 234 mem 4140
$ nstat -n ; sleep 10 ; nstat |grep Pressure
TcpExtTCPMemoryPressures 1700
TcpExtTCPMemoryPressuresChrono 5209
v2: Used EXPORT_SYMBOL_GPL() instead of EXPORT_SYMBOL() as David
instructed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This counter records the number of times the firewall blackhole issue is
detected and active TFO is disabled.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tcp_tw_recycle was already broken for connections
behind NAT, since the per-destination timestamp is not
monotonically increasing for multiple machines behind
a single destination address.
After the randomization of TCP timestamp offsets
in commit 8a5bd45f6616 (tcp: randomize tcp timestamp offsets
for each connection), the tcp_tw_recycle is broken for all
types of connections for the same reason: the timestamps
received from a single machine is not monotonically increasing,
anymore.
Remove tcp_tw_recycle, since it is not functional. Also, remove
the PAWSPassive SNMP counter since it is only used for
tcp_tw_recycle, and simplify tcp_v4_route_req and tcp_v6_route_req
since the strict argument is only set when tcp_tw_recycle is
enabled.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Cc: Lutz Vieweg <lvml@5t9.de>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Debugging issues caused by pfmemalloc is often tedious.
Add a new SNMP counter to more easily diagnose these problems.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Josef Bacik <jbacik@fb.com>
Acked-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shaohua Li made percpu_counter irq safe in commit 098faf5805
("percpu_counter: make APIs irq safe")
We can safely remove BH disable/enable sections around various
percpu_counter manipulations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different namespace application might require fast recycling
TIME-WAIT sockets independently of the host.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to suppress the checkpatch.pl warning "Comparison to NULL
could be written". No functional changes here.
Signed-off-by: Jia He <hejianet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to use the generic interfaces snmp_get_cpu_field{,64}_batch to
aggregate the data by going through all the items of each cpu sequentially.
Then snmp_seq_show is split into 2 parts to avoid build warning "the frame
size" larger than 1024.
Signed-off-by: Jia He <hejianet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds SNMP counter for drops caused by MD5 mismatches.
The current syslog might help, but a counter is more precise and helps
monitoring.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Diagnosing problems related to Window Probes has been hard because
we lack a counter.
TCPWinProbe counts the number of ACK packets a sender has to send
at regular intervals to make sure a reverse ACK packet opening back
a window had not been lost.
TCPKeepAlive counts the number of ACK packets sent to keep TCP
flows alive (SO_KEEPALIVE)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a timer wheel for timewait sockets was nice ~15 years ago when
memory was expensive and machines had a single processor.
This does not scale, code is ugly and source of huge latencies
(Typically 30 ms have been seen, cpus spinning on death_lock spinlock.)
We can afford to use an extra 64 bytes per timewait sock and spread
timewait load to all cpus to have better behavior.
Tested:
On following test, /proc/sys/net/ipv4/tcp_tw_recycle is set to 1
on the target (lpaa24)
Before patch :
lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
419594
lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
437171
While test is running, we can observe 25 or even 33 ms latencies.
lpaa24:~# ping -c 1000 -i 0.02 -qn lpaa23
...
1000 packets transmitted, 1000 received, 0% packet loss, time 20601ms
rtt min/avg/max/mdev = 0.020/0.217/25.771/1.535 ms, pipe 2
lpaa24:~# ping -c 1000 -i 0.02 -qn lpaa23
...
1000 packets transmitted, 1000 received, 0% packet loss, time 20702ms
rtt min/avg/max/mdev = 0.019/0.183/33.761/1.441 ms, pipe 2
After patch :
About 90% increase of throughput :
lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
810442
lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
800992
And latencies are kept to minimal values during this load, even
if network utilization is 90% higher :
lpaa24:~# ping -c 1000 -i 0.02 -qn lpaa23
...
1000 packets transmitted, 1000 received, 0% packet loss, time 19991ms
rtt min/avg/max/mdev = 0.023/0.064/0.360/0.042 ms
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Helpers for mitigating ACK loops by rate-limiting dupacks sent in
response to incoming out-of-window packets.
This patch includes:
- rate-limiting logic
- sysctl to control how often we allow dupacks to out-of-window packets
- SNMP counter for cases where we rate-limited our dupack sending
The rate-limiting logic in this patch decides to not send dupacks in
response to out-of-window segments if (a) they are SYNs or pure ACKs
and (b) the remote endpoint is sending them faster than the configured
rate limit.
We rate-limit our responses rather than blocking them entirely or
resetting the connection, because legitimate connections can rely on
dupacks in response to some out-of-window segments. For example, zero
window probes are typically sent with a sequence number that is below
the current window, and ZWPs thus expect to thus elicit a dupack in
response.
We allow dupacks in response to TCP segments with data, because these
may be spurious retransmissions for which the remote endpoint wants to
receive DSACKs. This is safe because segments with data can't
realistically be part of ACK loops, which by their nature consist of
each side sending pure/data-less ACKs to each other.
The dupack interval is controlled by a new sysctl knob,
tcp_invalid_ratelimit, given in milliseconds, in case an administrator
needs to dial this upward in the face of a high-rate DoS attack. The
name and units are chosen to be analogous to the existing analogous
knob for ICMP, icmp_ratelimit.
The default value for tcp_invalid_ratelimit is 500ms, which allows at
most one such dupack per 500ms. This is chosen to be 2x faster than
the 1-second minimum RTO interval allowed by RFC 6298 (section 2, rule
2.4). We allow the extra 2x factor because network delay variations
can cause packets sent at 1 second intervals to be compressed and
arrive much closer.
Reported-by: Avery Fay <avery@mixpanel.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deploying FQ pacing, one thing we noticed is that CUBIC Hystart
triggers too soon.
Having SNMP counters to have an idea of how often the various Hystart
methods trigger is useful prior to any modifications.
This patch adds SNMP counters tracking, how many time "ack train" or
"Delay" based Hystart triggers, and cumulative sum of cwnd at the time
Hystart decided to end SS (Slow Start)
myhost:~# nstat -a | grep Hystart
TcpExtTCPHystartTrainDetect 9 0.0
TcpExtTCPHystartTrainCwnd 20650 0.0
TcpExtTCPHystartDelayDetect 10 0.0
TcpExtTCPHystartDelayCwnd 360 0.0
->
Train detection was triggered 9 times, and average cwnd was
20650/9=2294,
Delay detection was triggered 10 times and average cwnd was 36
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As NIC multicast filtering isn't perfect, and some platforms are
quite content to spew broadcasts, we should not trigger an event
for skb:kfree_skb when we do not have a match for such an incoming
datagram. We do though want to avoid sweeping the matter under the
rug entirely, so increment a suitable statistic.
This incorporates feedback from David L. Stevens, Karl Neiss and Eric
Dumazet.
V3 - use bool per David Miller
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'nqueues' counter is protected by the lru list lock,
once thats removed this needs to be converted to atomic
counter. Given this isn't used for anything except for
reporting it to userspace via /proc, just remove it.
We still report the memory currently used by fragment
reassembly queues.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 8f0ea0fe3a (snmp: reduce percpu needs by 50%)
reduced snmp array size to 1, so technically it doesn't have to be
an array any more. What's more, after the following commit:
commit 933393f58f
Date: Thu Dec 22 11:58:51 2011 -0600
percpu: Remove irqsafe_cpu_xxx variants
We simply say that regular this_cpu use must be safe regardless of
preemption and interrupt state. That has no material change for x86
and s390 implementations of this_cpu operations. However, arches that
do not provide their own implementation for this_cpu operations will
now get code generated that disables interrupts instead of preemption.
probably no arch wants to have SNMP_ARRAY_SZ == 2. At least after
almost 3 years, no one complains.
So, just convert the array to a single pointer and remove snmp_mib_init()
and snmp_mib_free() as well.
Cc: Christoph Lameter <cl@linux.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following snmp stats:
TCPFastOpenActiveFail: Fast Open attempts (SYN/data) failed beacuse
the remote does not accept it or the attempts timed out.
TCPSynRetrans: number of SYN and SYN/ACK retransmits to break down
retransmissions into SYN, fast-retransmits, timeout retransmits, etc.
TCPOrigDataSent: number of outgoing packets with original data (excluding
retransmission but including data-in-SYN). This counter is different from
TcpOutSegs because TcpOutSegs also tracks pure ACKs. TCPOrigDataSent is
more useful to track the TCP retransmission rate.
Change TCPFastOpenActive to track only successful Fast Opens to be symmetric to
TCPFastOpenPassive.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Lawrence Brakmo <brakmo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three counters are added:
- one to track when we went from non-zero to zero window
- one to track the reverse
- one counter incremented when we want to announce zero window,
but can't because we would shrink current window.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of TCP Small Queues, TSO auto sizing, and TCP
pacing, we can implement Automatic Corking in the kernel, to help
applications doing small write()/sendmsg() to TCP sockets.
Idea is to change tcp_push() to check if the current skb payload is
under skb optimal size (a multiple of MSS bytes)
If under 'size_goal', and at least one packet is still in Qdisc or
NIC TX queues, set the TCP Small Queue Throttled bit, so that the push
will be delayed up to TX completion time.
This delay might allow the application to coalesce more bytes
in the skb in following write()/sendmsg()/sendfile() system calls.
The exact duration of the delay is depending on the dynamics
of the system, and might be zero if no packet for this flow
is actually held in Qdisc or NIC TX ring.
Using FQ/pacing is a way to increase the probability of
autocorking being triggered.
Add a new sysctl (/proc/sys/net/ipv4/tcp_autocorking) to control
this feature and default it to 1 (enabled)
Add a new SNMP counter : nstat -a | grep TcpExtTCPAutoCorking
This counter is incremented every time we detected skb was under used
and its flush was deferred.
Tested:
Interesting effects when using line buffered commands under ssh.
Excellent performance results in term of cpu usage and total throughput.
lpq83:~# echo 1 >/proc/sys/net/ipv4/tcp_autocorking
lpq83:~# perf stat ./super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128
9410.39
Performance counter stats for './super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128':
35209.439626 task-clock # 2.901 CPUs utilized
2,294 context-switches # 0.065 K/sec
101 CPU-migrations # 0.003 K/sec
4,079 page-faults # 0.116 K/sec
97,923,241,298 cycles # 2.781 GHz [83.31%]
51,832,908,236 stalled-cycles-frontend # 52.93% frontend cycles idle [83.30%]
25,697,986,603 stalled-cycles-backend # 26.24% backend cycles idle [66.70%]
102,225,978,536 instructions # 1.04 insns per cycle
# 0.51 stalled cycles per insn [83.38%]
18,657,696,819 branches # 529.906 M/sec [83.29%]
91,679,646 branch-misses # 0.49% of all branches [83.40%]
12.136204899 seconds time elapsed
lpq83:~# echo 0 >/proc/sys/net/ipv4/tcp_autocorking
lpq83:~# perf stat ./super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128
6624.89
Performance counter stats for './super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128':
40045.864494 task-clock # 3.301 CPUs utilized
171 context-switches # 0.004 K/sec
53 CPU-migrations # 0.001 K/sec
4,080 page-faults # 0.102 K/sec
111,340,458,645 cycles # 2.780 GHz [83.34%]
61,778,039,277 stalled-cycles-frontend # 55.49% frontend cycles idle [83.31%]
29,295,522,759 stalled-cycles-backend # 26.31% backend cycles idle [66.67%]
108,654,349,355 instructions # 0.98 insns per cycle
# 0.57 stalled cycles per insn [83.34%]
19,552,170,748 branches # 488.244 M/sec [83.34%]
157,875,417 branch-misses # 0.81% of all branches [83.34%]
12.130267788 seconds time elapsed
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename mib counter from "low latency" to "busy poll"
v1 also moved the counter to the ip MIB (suggested by Shawn Bohrer)
Eric Dumazet suggested that the current location is better.
So v2 just renames the counter to fit the new naming convention.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With GRO/LRO processing, there is a problem because Ip[6]InReceives SNMP
counters do not count the number of frames, but number of aggregated
segments.
Its probably too late to change this now.
This patch adds four new counters, tracking number of frames, regardless
of LRO/GRO, and on a per ECN status basis, for IPv4 and IPv6.
Ip[6]NoECTPkts : Number of packets received with NOECT
Ip[6]ECT1Pkts : Number of packets received with ECT(1)
Ip[6]ECT0Pkts : Number of packets received with ECT(0)
Ip[6]CEPkts : Number of packets received with Congestion Experienced
lph37:~# nstat | egrep "Pkts|InReceive"
IpInReceives 1634137 0.0
Ip6InReceives 3714107 0.0
Ip6InNoECTPkts 19205 0.0
Ip6InECT0Pkts 52651828 0.0
IpExtInNoECTPkts 33630 0.0
IpExtInECT0Pkts 15581379 0.0
IpExtInCEPkts 6 0.0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds an ndo_ll_poll method and the code that supports it.
This method can be used by low latency applications to busy-poll
Ethernet device queues directly from the socket code.
sysctl_net_ll_poll controls how many microseconds to poll.
Default is zero (disabled).
Individual protocol support will be added by subsequent patches.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MIB counters for checksum errors in IP layer,
and TCP/UDP/ICMP layers, to help diagnose problems.
$ nstat -a | grep Csum
IcmpInCsumErrors 72 0.0
TcpInCsumErrors 382 0.0
UdpInCsumErrors 463221 0.0
Icmp6InCsumErrors 75 0.0
Udp6InCsumErrors 173442 0.0
IpExtInCsumErrors 10884 0.0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Host queues (Qdisc + NIC) can hold packets so long that TCP can
eventually retransmit a packet before the first transmit even left
the host.
Its not clear right now if we could avoid this in the first place :
- We could arm RTO timer not at the time we enqueue packets, but
at the time we TX complete them (tcp_wfree())
- Cancel the sending of the new copy of the packet if prior one
is still in queue.
This patch adds instrumentation so that we can at least see how
often this problem happens.
TCPSpuriousRtxHostQueues SNMP counter is incremented every time
we detect the fast clone is not yet freed in tcp_transmit_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the second of the TLP patch series; it augments the basic TLP
algorithm with a loss detection scheme.
This patch implements a mechanism for loss detection when a Tail
loss probe retransmission plugs a hole thereby masking packet loss
from the sender. The loss detection algorithm relies on counting
TLP dupacks as outlined in Sec. 3 of:
http://tools.ietf.org/html/draft-dukkipati-tcpm-tcp-loss-probe-01
The basic idea is: Sender keeps track of TLP "episode" upon
retransmission of a TLP packet. An episode ends when the sender receives
an ACK above the SND.NXT (tracked by tlp_high_seq) at the time of the
episode. We want to make sure that before the episode ends the sender
receives a "TLP dupack", indicating that the TLP retransmission was
unnecessary, so there was no loss/hole that needed plugging. If the
sender gets no TLP dupack before the end of the episode, then it reduces
ssthresh and the congestion window, because the TLP packet arriving at
the receiver probably plugged a hole.
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series implement the Tail loss probe (TLP) algorithm described
in http://tools.ietf.org/html/draft-dukkipati-tcpm-tcp-loss-probe-01. The
first patch implements the basic algorithm.
TLP's goal is to reduce tail latency of short transactions. It achieves
this by converting retransmission timeouts (RTOs) occuring due
to tail losses (losses at end of transactions) into fast recovery.
TLP transmits one packet in two round-trips when a connection is in
Open state and isn't receiving any ACKs. The transmitted packet, aka
loss probe, can be either new or a retransmission. When there is tail
loss, the ACK from a loss probe triggers FACK/early-retransmit based
fast recovery, thus avoiding a costly RTO. In the absence of loss,
there is no change in the connection state.
PTO stands for probe timeout. It is a timer event indicating
that an ACK is overdue and triggers a loss probe packet. The PTO value
is set to max(2*SRTT, 10ms) and is adjusted to account for delayed
ACK timer when there is only one oustanding packet.
TLP Algorithm
On transmission of new data in Open state:
-> packets_out > 1: schedule PTO in max(2*SRTT, 10ms).
-> packets_out == 1: schedule PTO in max(2*RTT, 1.5*RTT + 200ms)
-> PTO = min(PTO, RTO)
Conditions for scheduling PTO:
-> Connection is in Open state.
-> Connection is either cwnd limited or no new data to send.
-> Number of probes per tail loss episode is limited to one.
-> Connection is SACK enabled.
When PTO fires:
new_segment_exists:
-> transmit new segment.
-> packets_out++. cwnd remains same.
no_new_packet:
-> retransmit the last segment.
Its ACK triggers FACK or early retransmit based recovery.
ACK path:
-> rearm RTO at start of ACK processing.
-> reschedule PTO if need be.
In addition, the patch includes a small variation to the Early Retransmit
(ER) algorithm, such that ER and TLP together can in principle recover any
N-degree of tail loss through fast recovery. TLP is controlled by the same
sysctl as ER, tcp_early_retrans sysctl.
tcp_early_retrans==0; disables TLP and ER.
==1; enables RFC5827 ER.
==2; delayed ER.
==3; TLP and delayed ER. [DEFAULT]
==4; TLP only.
The TLP patch series have been extensively tested on Google Web servers.
It is most effective for short Web trasactions, where it reduced RTOs by 15%
and improved HTTP response time (average by 6%, 99th percentile by 10%).
The transmitted probes account for <0.5% of the overall transmissions.
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
proc_net_remove is only used to remove proc entries
that under /proc/net,it's not a general function for
removing proc entries of netns. if we want to remove
some proc entries which under /proc/net/stat/, we still
need to call remove_proc_entry.
this patch use remove_proc_entry to replace proc_net_remove.
we can remove proc_net_remove after this patch.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, some modules such as bonding use proc_create
to create proc entries under /proc/net/, and other modules
such as ipv4 use proc_net_fops_create.
It looks a little chaos.this patch changes all of
proc_net_fops_create to proc_create. we can remove
proc_net_fops_create after this patch.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds all the necessary data structure and support
functions to implement TFO server side. It also documents a number
of flags for the sysctl_tcp_fastopen knob, and adds a few Linux
extension MIBs.
In addition, it includes the following:
1. a new TCP_FASTOPEN socket option an application must call to
supply a max backlog allowed in order to enable TFO on its listener.
2. A number of key data structures:
"fastopen_rsk" in tcp_sock - for a big socket to access its
request_sock for retransmission and ack processing purpose. It is
non-NULL iff 3WHS not completed.
"fastopenq" in request_sock_queue - points to a per Fast Open
listener data structure "fastopen_queue" to keep track of qlen (# of
outstanding Fast Open requests) and max_qlen, among other things.
"listener" in tcp_request_sock - to point to the original listener
for book-keeping purpose, i.e., to maintain qlen against max_qlen
as part of defense against IP spoofing attack.
3. various data structure and functions, many in tcp_fastopen.c, to
support server side Fast Open cookie operations, including
/proc/sys/net/ipv4/tcp_fastopen_key to allow manual rekeying.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements sending SYN-data in tcp_connect(). The data is
from tcp_sendmsg() with flag MSG_FASTOPEN (implemented in a later patch).
The length of the cookie in tcp_fastopen_req, init'd to 0, controls the
type of the SYN. If the cookie is not cached (len==0), the host sends
data-less SYN with Fast Open cookie request option to solicit a cookie
from the remote. If cookie is not available (len > 0), the host sends
a SYN-data with Fast Open cookie option. If cookie length is negative,
the SYN will not include any Fast Open option (for fall back operations).
To deal with middleboxes that may drop SYN with data or experimental TCP
option, the SYN-data is only sent once. SYN retransmits do not include
data or Fast Open options. The connection will fall back to regular TCP
handshake.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the RFC 5691 mitigation against Blind
Reset attack using SYN bit.
Section 4.2 of RFC 5961 advises to send a Challenge ACK and drop
incoming packet, instead of resetting the session.
Add a new SNMP counter to count number of challenge acks sent
in response to SYN packets.
(netstat -s | grep TCPSYNChallenge)
Remove obsolete TCPAbortOnSyn, since we no longer abort a TCP session
because of a SYN flag.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kiran Kumar Kella <kkiran@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the RFC 5691 mitigation against Blind
Reset attack using RST bit.
Idea is to validate incoming RST sequence,
to match RCV.NXT value, instead of previouly accepted
window : (RCV.NXT <= SEG.SEQ < RCV.NXT+RCV.WND)
If sequence is in window but not an exact match, send
a "challenge ACK", so that the other part can resend an
RST with the appropriate sequence.
Add a new sysctl, tcp_challenge_ack_limit, to limit
number of challenge ACK sent per second.
Add a new SNMP counter to count number of challenge acks sent.
(netstat -s | grep TCPChallengeACK)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kiran Kumar Kella <kkiran@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add three SNMP TCP counters, to better track TCP behavior
at global stage (netstat -s), when packets are received
Out Of Order (OFO)
TCPOFOQueue : Number of packets queued in OFO queue
TCPOFODrop : Number of packets meant to be queued in OFO
but dropped because socket rcvbuf limit hit.
TCPOFOMerge : Number of packets in OFO that were merged with
other packets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With increasing receive window sizes, but speed of light not improved
that much, out of order queue can contain a huge number of skbs, waiting
to be moved to receive_queue when missing packets can fill the holes.
Some devices happen to use fat skbs (truesize of 4096 + sizeof(struct
sk_buff)) to store regular (MTU <= 1500) frames. This makes highly
probable sk_rmem_alloc hits sk_rcvbuf limit, which can be 4Mbytes in
many cases.
When limit is hit, tcp stack calls tcp_collapse_ofo_queue(), a true
latency killer and cpu cache blower.
Doing the coalescing attempt each time we add a frame in ofo queue
permits to keep memory use tight and in many cases avoid the
tcp_collapse() thing later.
Tested on various wireless setups (b43, ath9k, ...) known to use big skb
truesize, this patch removed the "packets collapsed in receive queue due
to low socket buffer" I had before.
This also reduced average memory used by tcp sockets.
With help from Neal Cardwell.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It might be useful to get a counter of failed tcp_retransmit_skb()
calls.
Reported-by: Satoru Moriya <satoru.moriya@hds.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correctly implement a loss detection heuristic: New sequences (above
high_seq) sent during the fast recovery are deemed lost when higher
sequences are SACKed.
Current code does not catch these losses, because tcp_mark_head_lost()
does not check packets beyond high_seq. The fix is straight-forward by
checking packets until the highest sacked packet. In addition, all the
FLAG_DATA_LOST logic are in-effective and redundant and can be removed.
Update the loss heuristic comments. The algorithm above is documented
as heuristic B, but it is redundant too because heuristic A already
covers B.
Note that this change only marks some forward-retransmitted packets LOST.
It does NOT forbid TCP performing further CWR on new losses. A potential
follow-up patch under preparation is to perform another CWR on "new"
losses such as
1) sequence above high_seq is lost (by resetting high_seq to snd_nxt)
2) retransmission is lost.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces all uses of struct sock fields' memory_pressure,
memory_allocated, sockets_allocated, and sysctl_mem to acessor
macros. Those macros can either receive a socket argument, or a mem_cgroup
argument, depending on the context they live in.
Since we're only doing a macro wrapping here, no performance impact at all is
expected in the case where we don't have cgroups disabled.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Reviewed-by: Hiroyouki Kamezawa <kamezawa.hiroyu@jp.fujitsu.com>
CC: David S. Miller <davem@davemloft.net>
CC: Eric W. Biederman <ebiederm@xmission.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading /proc/net/snmp on a machine with a lot of cpus is very expensive
(can be ~88000 us).
This is because ICMPMSG MIB uses 4096 bytes per cpu, and folding values
for all possible cpus can read 16 Mbytes of memory.
ICMP messages are not considered as fast path on a typical server, and
eventually few cpus handle them anyway. We can afford an atomic
operation instead of using percpu data.
This saves 4096 bytes per cpu and per network namespace.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These files are non modular, but need to export symbols using
the macros now living in export.h -- call out the include so
that things won't break when we remove the implicit presence
of module.h from everywhere.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
"Possible SYN flooding on port xxxx " messages can fill logs on servers.
Change logic to log the message only once per listener, and add two new
SNMP counters to track :
TCPReqQFullDoCookies : number of times a SYNCOOKIE was replied to client
TCPReqQFullDrop : number of times a SYN request was dropped because
syncookies were not enabled.
Based on a prior patch from Tom Herbert, and suggestions from David.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than printing the message to the log, use a mib counter to keep
track of the count of occurences of time wait bucket overflow. Reduces
spam in logs.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan
Yuchung Cheng
Florian Westphal
Eric Dumazet
Wei Wang
Soheil Hassas Yeganeh
Haishuang Yan
Jia He
Nikolay Borisov
Rick Jones
Neal Cardwell
Fabian Frederick
WANG Cong
Weilong Chen
David S. Miller
Eliezer Tamir
Nandita Dukkipati
Gao feng
Jerry Chu
Eric Dumazet
Glauber Costa
Paul Gortmaker
Tom Herbert