isr function issues SPI read command to mrf to obtain INTSTAT.
SPI transfer is 2 bytes, but value of 2nd byte is not defined.
This had the effect that only the first ISR worked as intended. The
second ISR read incorrect INTSTAT values. Observed on Raspberry PI B+.
Signed-off-by: Walter Mack <wmack@componentsw.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For my RIOT-OS in userspace experiments I need to create a fakelb
monitor interface. The fakelb doesn't filter anything on L2 and is a
purely raw interface. Because nl802154 checks on promiscuous mode which
need to supported by creating monitors this patch adds some no-op
promiscuous mode setting and the promiscuous flag.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes the behaviour to not overwrite csma settings when
set channel afterwards.
Cc: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If DEBUG is defined, a superfluous closing brace
is introduced.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Catching up with the stack here and implement CCA mode setting.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Catching up with the stack here and implement CCA ED level setting.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Catching up with the stack here and implement CSMA parameter setting.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
I expierenced when setting channel while sleep mode it didn't changed
the channel inside the hardware registers. Then I got another report of
an user which has similar issues.
I increased the sleep to off state change timing, which is according
at86rf233 at maximum 1000 us. After this change I got no similar effects
again.
I tried another option to wait on AWAKE_END irq, which can be used to
wait until the transceiver is awaked. I tested it and the IRQ took 4
seconds after starting state change. I don't believe it takes 4 seconds
to go into the TRX_OFF state from SLEEP state. The alternative is to
increase the timings which seems to work.
Cc: Oleg Hahm <oliver.hahm@inria.fr>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Reviewed-by: Stefan Schmidt<stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We set the TXNSECEN bit of register TXNCON to on when transmitting a
security-enabled frame, as described in section 3.12.2 of the MRF
datasheet.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Alexandre Macabies <web+oss@zopieux.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When receiving a security-enabled IEEE 802.15.4 frame, the MRF24J40
triggers a SECIF interrupt that needs to be handled for RX processing
to keep functioning properly.
This patch enables the SECIF interrupt and makes the MRF ignores all
hardware processing of security-enabled frames, that is handled by the
ieee802154 stack instead.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Alexandre Macabies <web+oss@zopieux.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Alan Ott <alan@signal11.us>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the firmware upload or the firmware verification fails then we
printed the error message and exited but we missed releasing the
firmware.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a missing reg for writeable stuff for regmap.
Cc: Alan Ott <alan@signal11.us>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch force always to set "is_tx_from_off", when calibration
timeout was not occurred. In case of error handling the is_tx_from_off
can be inside in an invalid state.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The resource "ctx" can be still used by at86rf230_async_state_change, we
need to free it at the complete handler of the async state change to
avoid a use after free.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds checking the "CRC_OK" bit at the end of packets coming
from the CC2520 radio. It also adds support for putting the radio in
promiscuous mode (in which packets are not dropped if the CRC fails).
In promiscuous mode the AUTOCRC flag is cleared so that the driver can
pass the received CRC to the monitors.
The radio now defaults to frame filtering (checking that the destination
and PANID in the incoming packet matches the local node). This matches
the other 15.4 radios and is what a user would expect to be the default.
Other changes:
1. Adds LQI calculation
2. Makes #defines for relevant bit fields in CC2520 registers
Signed-off-by: Brad Campbell <bradjc5@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This driver has been sitting in the linux-zigbee[2] repository for a long
time. We updated it from time to time and made it available via our
github kernel repository. The Linux MAC802.15.4 support has improved a lot
since then. Thanks to all! So it’s finally time to upstream this driver.
The ADF7242 requires an add-on firmware for the automatic IEEE 802.15.4
operating modes. The firmware file is currently made available on the
ADF7242 wiki page here [1]
[1] http://wiki.analog.com/resources/tools-software/linux-drivers/networking-mac802154/adf7242
[2] http://sourceforge.net/p/linux-zigbee/kernel/ci/devel/tree/drivers/ieee802154/adf7242.c
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The kfree_skb() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch removes a trailing semicolon which was introduced by commit
d3f1bc3 ("mrf24j40: add cca mode support") and reported by kbuild test
robot.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces some magic numbers with defines for register bits,
mask and shifts.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the irq trigger type value while calling
devm_request_irq by using IRQF_TRIGGER_LOW when no irq type was given.
Additional we add support for change the irq polarity while hw init if
high level or low level triggered irq type are given.
For rising edge triggered irq's the mrf24j40 can't deal with that, this
races at position of tx completion irq, while the irq is disabled we
readout the irq status registers. This will resets the irq line so other
irq's can occur. Wile readout the irq status register the irq is still
disabled and edge triggered interrupts will be ignored.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for promiscuous mode by setting promiscuous (no
frame filtering), disable automatic ack handling and not filtering
frames where the crc is invalid.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch supports setting of transmit power for the mrf24j40ma
transceiver only. The mrf24j40mc has some amplifier to change the
transmit power, I am currently not sure how the mapping for this
amplifier looks like.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch supports handling to set the cca energy detection level for
the mrf24j40 transceiver.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch supports cca mode handling for mrf24j40.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds supports to change the CSMA parameters. The datasheet
doesn't say anything about max_be value. Seems not configurable and we
assume the 802.15.4 default. But this value must exists because there is
a min_be value.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the threaded irq handling and do a hardirq instead.
We need to switch to spi_async for this step for getting the irq status
register.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch prepares that we can do the receive handling inside interrupt
context by using spi_async. This is necessary for introduce a
non-threaded irq handling.
Also we drop the bit setting for "RXDECINV" at register "BBREG1", we do
a driectly full write of register "BBREG1", because it contains the bit
RXDECINV only.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch reworks the current transmit API to spi_async handling. We
removed the error handling check, because mac802154 has no chance to
report it. Also the transmit timeout handling can't be handled by xmit
async handling, for this usecase we need to implement the netdev
watchdog. These are all unlikely cases which we drop now and should be
provided by netdev watchdog.
We also drop the bit setting for TXNACKREQ at register TXNCON, this is
not necessary. The TXNCON register should set only once for each frame,
previous settings doesn't matter.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the frame delivery to mac802154 with crc. This is
useful for monitor interface types which deliver the crc to userspace.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch uses the regmap functions for transceiver register settings
where it's possible. This means everything except the hotpaths like
receive/transmit handling.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce regmap support for short and long address space of
mrf24j40. It's only possible to use regmap_read/write/update_bits for
long address range. This is because I added lowlevel bus operation
because the write operation need to set the 12th bit to mark a register
write, but regmap only supports to set bits for register write access in
the first byte. We use other regmap register functions than
read/write/update_bits, so this should be fine.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For supporting regmap, this patch will add more register defines to
prepare a full register dump by regmap debugfs.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The mrf24j40 has no source to get a permanent extended address. This
patch will add a random generated permanent extended address source.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Per default mrf24j40 has the channel 11 after reset. This patch adds the
right phy default value for the channel setting.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds devicetree support to mrf24j40 with proper devicetree
compatible strings.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes spi settings while mrf24j40 probing. These settings
cannot be overwrite while device probing where spi controller should be
already configured. These settings need to be setup by device tree or
platform data.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The function ieee802154_register_hw should always called at last.
Currently we do hardware init and such things after register hardware
into the subsystem. It could be that the subsystem already call driver
operations while running hardware init.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the own private dataroom allocation by calling
devm_kzalloc for devrec and assign this pointer to "devrec->hw->priv".
Instead we using like all other drivers ieee802154_alloc_hw and give the
size for the private driver dataroom at the first argument.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces the spaces after define by a tab.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for edge triggered irq types. We remove the
locking for irq resources by enable/disable irq and allocate directly
some heap buffer at isr. We have still a enable/disable irq path but
this is for level-triggered irq's which need to be disabled until
spi_async clear the irq line.
There is usually a little race condition between "irq line cleared" and
"enable_irq". When in this time a edge triggered irq arrived, we will
not recognize this interrupt. This case can't happend at at86rf230. The
reason is that we unmask TRX_END irq's only which indicates a transmit
or receive completion, which depends on the current state.
On Transmit:
TRX_END arrived and transceiver is in TX_ARET_ON state again, in this
state no other TRX_END can happen until we leave the state.
On Receive:
This is protected with the RX_SAFE_MODE bit which leaves the transceiver
in RX_AACK_BUSY until we readed the framebuffer. In this state no other
TRX_END can happen.
Tested with RPi where I first detected issues between edge/level irq's.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alexander Aring <alex.aring@gmail.com>
Cc: Stefan Schmidt <stefan@osg.samsung.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch supports handling for printout different chipnames between
atusb and rzusb. The rzusb contains an at86rf230 and atusb an at86rf231
transceiver.
Cc: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce a more detailed information why edge triggered
irq's are currently not recommended. It could be that rising/falling
edge detection can happen while the irq is disabled.
Suggested-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce debugfs support for collect trac status stats. To
clear the stats ifdown the interface of at86rf230 and start the
interface again.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To abort a TX_ARET_BUSY state it's recommended to switch into TRX_OFF
state by doing STATE_TRX_FORCE_OFF. This patch will do always a TRX_OFF
state change when the transceiver stucks in any state. From TRX_OFF we
can switch to the states which are also possible by TX_ON state.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When transmit is done, indicated by trx_end irq, we do first a force
state change to TX_ON and then checking the trac status, if the trac
status is unequal zero we do a state change to TRX_OFF.
This patch changes to the following behaviour, we first check on trac
status after trx_end occurs and then doing a normal change to TX_ON
without do the state change to TRX_OFF when trac status is unequal zero.
The reasons are that the datasheet doesn't described when the trac
status register is cleared, we should doing to evaluate the trac status
at first. The reason to remove the TRX_OFF change if the trac status is
unequal to zero and it was force is the following paragraph inside The
at86rf2xx datasheets:
"Using FORCE_PLL_ON to interrupt an TX_ARET transaction, it is
recommended to check register bits [7:5] of register address 0x32 for
value 0. If this value is different, TRX_CMD sequence FORCE_TRX_OFF shall
be used immediately followed by TRX_CMD sequence PLL_ON. This performs a
state transition to PLL_ON."
The meaning is here "to interrupt an TX_ARET transaction" in case of
trx_end interrupt the "TX_ARET transaction" is already done and we don't
interrupt the "TX_ARET transaction" by doing the change to TX_ON (PLL_ON)
here. Additional I changed the force change to normal TX_ON which seems to
work here.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the device tree support is disabled, the fifo_pin is uninitialized,
this patch will set the fifo_pin value based on platform data
Signed-off-by: Yong Li <sdliyong@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Walter Mack
Alexander Aring
xypron.glpk@gmx.de
Stefan Schmidt
Alexandre Macabies
Sudip Mukherjee
Brad Campbell
Michael Hennerich
Markus Elfring
Linus Torvalds
Andrew F. Davis
Alexander Aring
Stephen Rothwell
Yong Li