- sdhc node renamed to sdhci ("sdhc" name is confusing since SDHC is
used to name Secure Digital High Capacity cards, while SDHCI is an
interface).
- Get rid of "fsl,esdhc" compatible entry, it's replaced by the
"fsl,<chip>-esdhc" scheme;
- Get rid of `model' property.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
TSEC0 is connected to Vitesse 7385 5-port switch. The switch
isn't connected to any mdio bus, the link to the switch is fixed
to Full-duplex 1000 Mb/s (no pause).
This patch fixes following failure during bootup:
mdio@24520:01 not found
eth0: Could not attach to PHY
IP-Config: Failed to open eth0
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit b31a1d8b41 ("gianfar: Convert
gianfar to an of_platform_driver") introduced a child node for
the ethernet@25000 controller, but no address and size cells
specifiers were added, and that makes dtc unhappy:
DTC: dts->dtb on file "arch/powerpc/boot/dts/mpc8313erdb.dts"
Warning (reg_format): "reg" property in /soc8313@e0000000/ethernet@25000/mdio@25520 has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc8313@e0000000/ethernet@25000/mdio@25520
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc8313@e0000000/ethernet@25000/mdio@25520
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Board support for the InterControl Digsy-MTC device based on the MPC5200B SoC.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds board support for the Media5200 platform. Changes are:
- add the media5200 device tree
- add the media5200 platform support code and cascaded interrupt controller
- add media5200 to the build targets.
Note: this patch also includes a minor tweak to the lite5200(b) target
images list to add the .dtb files to the image list.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Trim out obsolete/extraneous properties and tighten up some usage
conventions. Changes include:
- removal of device_type properties
- removal of cell-index properties
- Addition of gpio-controller and #gpio-cells properties to gpio
nodes
- Move common interrupt-parent property out of device nodes and
into top level parent node.
This patch also include what looks to be just trivial editorial
whitespace/format changes, but there is real method in this
madness. Editorial changes were made to keep the all the
mpc5200 board device trees as similar as possible so that diffs
between them only show the real differences between the boards.
The pcm030 device tree was most affected by this because many
of the comments had been changed from // to /* */ style and
some cell values where changed from decimal to hex format when
it was cloned from one of the other 5200 device trees.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Automatic I2C device probing is not done any more. Therefore we need
proper DTS device node definitions for the I2C LM75 thermal sensor on
the TQM85xx modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC310 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the basic board support for GE Fanuc's SBC310, a 3U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds pcie nodes to the appropriate dts files, plus adds
some probing code for the boards.
Also, remove of_device_is_avaliable() check from the mpc837x_mds.c
board file, as mpc83xx_add_bridge() has the same check now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Probe the new mdio node added by b31a1d8b. Fix kernel panic problem when
gianfar driver wants to get the of_platform_device of that mdio.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Convert the Warp platform to use the newly merged NDFC driver
- warp.dts changed to work with ndfc
- warp-nand.c no longer needed
- removed obsolete rev A support from cuboot-warp.c
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Added additional information for type and compatibility strings and
interrupt information to the SDRAM0 memory-controller device tree
nodes for AMCC PowerPC 405EX[r]-based boards to facilitate binding
with the new "ibm,sdram-4xx-ddr2" EDAC memory controller adapter driver.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
FSL U-Boots use /soc8315@e0000000 node to search and fixup serial
nodes' clock-frequency properties. Though in upstream kernels we use
new naming convention -- for IMMR address space dts files specify
/immr@e0000000 nodes.
This makes FSL U-Boots fail to fixup the clock frequencies, and that
leads to serial ports misbehaviour. We can workaround the issue by
filling the clock frequency values manually.
p.s. For the same reason FSL U-Boots fail to fixup MAC addresses for
ethernet nodes, so users should either change the .dts file locally
or set MAC address via `ifconfig hw ether' command.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the FPGA based watchdog timer on GE Fanuc's SBC610.
This patch enables one of the watchdog timers found on the SBC610. There are
two identical watchdog timers at different offsets in the above mentioned
boards, however the current driver is only capable of supporting one of them.
The watchdog timers are also capable of generating interrupts at a
user-configurable threshold, though support for this operation is currently
not supported by the driver.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch makes the default install script (arch/powerpc/boot/install.sh)
copy the bootable image files into the install directory. Before this
patch only the vmlinux image file was copied.
This patch makes the default 'make install' command useful for embedded
development when $(INSTALL_PATH) is set in the environment.
As a side effect, this patch changes the calling convention of the
install.sh script. Instead of a single 5th parameter, the script is now
passed a list of all the target images stored in the $(image-y) Makefile
variable. This should be backwards compatible with existing install scripts
since it just adds additional arguments and does not change existing ones.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (123 commits)
wimax/i2400m: add CREDITS and MAINTAINERS entries
wimax: export linux/wimax.h and linux/wimax/i2400m.h with headers_install
i2400m: Makefile and Kconfig
i2400m/SDIO: TX and RX path backends
i2400m/SDIO: firmware upload backend
i2400m/SDIO: probe/disconnect, dev init/shutdown and reset backends
i2400m/SDIO: header for the SDIO subdriver
i2400m/USB: TX and RX path backends
i2400m/USB: firmware upload backend
i2400m/USB: probe/disconnect, dev init/shutdown and reset backends
i2400m/USB: header for the USB bus driver
i2400m: debugfs controls
i2400m: various functions for device management
i2400m: RX and TX data/control paths
i2400m: firmware loading and bootrom initialization
i2400m: linkage to the networking stack
i2400m: Generic probe/disconnect, reset and message passing
i2400m: host/device procotol and core driver definitions
i2400m: documentation and instructions for usage
wimax: Makefile, Kconfig and docbook linkage for the stack
...
A published errata for ppc440epx states, that when running Linux with
both EHCI and OHCI modules loaded, the EHCI module experiences a fatal
error when a high-speed device is connected to the USB2.0, and
functions normally if OHCI module is not loaded.
There used to be recommendation to use only hi-speed or full-speed
devices with specific conditions, when respective module was unloaded.
Later, it was observed that ohci suspend is enough to keep things
going, and it was turned into workaround, as explained below.
Quote from original descriprion:
The 440EPx USB 2.0 Host controller is an EHCI compliant controller. In
USB 2.0 Host controllers, each EHCI controller has one or more companion
controllers, which may be OHCI or UHCI. An USB 2.0 Host controller will
contain one or more ports. For each port, only one of the controllers
is connected at any one time. In the 440EPx, there is only one OHCI
companion controller, and only one USB 2.0 Host port.
All ports on an USB 2.0 controller default to the companion
controller. If you load only an ohci driver, it will have control of
the ports and any deviceplugged in will operate, although high speed
devices will be forced to operate at full speed. When an ehci driver
is loaded, it explicitly takes control of the ports. If there is a
device connected, and / or every time there is a new device connected,
the ehci driver determines if the device is high speed or not. If it
is high speed, the driver retains control of the port. If it is not,
the driver explicitly gives the companion controller control of the
port.
The is a software workaround that uses
Initial version of the software workaround was posted to
linux-usb-devel:
http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg54019.html
and later available from amcc.com:
http://www.amcc.com/Embedded/Downloads/download.html?cat=1&family=15&ins=2
The patch below is generally based on the latter, but reworked to
powerpc/of_device USB drivers, and uses a few devicetree inquiries to
get rid of (some) hardcoded defines.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix misspelling of "firmware" in powerpc Makefile
It's spelled "firmware".
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The newest revision of uboot reworks the memory map for this
board to look more like the 85xx boards. Also, some regions
which were far larger than the actual hardware have been scaled
back to match the board, and the imaginary second flash bank has
been removed. Rapidio and PCI are mutually exclusive in the hardware,
and they now are occupying the same space in the address map.
The Rapidio node is commented out of the .dts since PCI is the
common use case.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Simply add the usb node to support USB host on the MPC8360E-RDK
boards.
Currently U-Boot doesn't fill the clock-frequency property for
timer nodes, so for now we have to fill it manually.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Update the device tree per QE USB bindings;
- Add timer (FSL GTM) node;
- Add gpio-controller node for BCSR13 bank (GPIOs on that bank
are used to control the USB transceiver);
- Set up other BCSR registers;
- Configure the QE Par IO.
The work is loosely based on Li Yang's patch[1], which was used
to support peripheral mode only.
[1] http://ozlabs.org/pipermail/linuxppc-dev/2008-August/061357.html
The s-o-b line of the original patch preserved here.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (144 commits)
powerpc/44x: Support 16K/64K base page sizes on 44x
powerpc: Force memory size to be a multiple of PAGE_SIZE
powerpc/32: Wire up the trampoline code for kdump
powerpc/32: Add the ability for a classic ppc kernel to be loaded at 32M
powerpc/32: Allow __ioremap on RAM addresses for kdump kernel
powerpc/32: Setup OF properties for kdump
powerpc/32/kdump: Implement crash_setup_regs() using ppc_save_regs()
powerpc: Prepare xmon_save_regs for use with kdump
powerpc: Remove default kexec/crash_kernel ops assignments
powerpc: Make default kexec/crash_kernel ops implicit
powerpc: Setup OF properties for ppc32 kexec
powerpc/pseries: Fix cpu hotplug
powerpc: Fix KVM build on ppc440
powerpc/cell: add QPACE as a separate Cell platform
powerpc/cell: fix build breakage with CONFIG_SPUFS disabled
powerpc/mpc5200: fix error paths in PSC UART probe function
powerpc/mpc5200: add rts/cts handling in PSC UART driver
powerpc/mpc5200: Make PSC UART driver update serial errors counters
powerpc/mpc5200: Remove obsolete code from mpc5200 MDIO driver
powerpc/mpc5200: Add MDMA/UDMA support to MPC5200 ATA driver
...
Fix trivial conflict in drivers/char/Makefile as per Paul's directions
Since the QPACE (Chromodynamics Parallel Computing on the
Cell Broadband Engine) platform doesn't use a iommu, doesn't
have PCI devices and a MPIC much lesser setup and
configurations are needed. So far all devices are detected
as OF device. A notifier function is used to set the dma_ops
for the of_platform bus. Further this patch splits the
PPC_CELL_NATIVE into PPC_CELL_COMMON which are parts that are
shared with the QPACE platform and the rest.
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The correct #address-cells was still used for the actual translation,
so the impact is only a possibility of choosing the wrong range entry
or failing to find any match. Most common cases were not affected.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Does the same for the accompanying MDIO driver, and then modifies the TBI
configuration method. The old way used fields in einfo, which no longer
exists. The new way is to create an MDIO device-tree node for each instance
of gianfar, and create a tbi-handle property to associate ethernet controllers
with the TBI PHYs they are connected to.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the localbus reg & range properties to respect that the top
level #address-cells and #size-cells = 2. The original commit
(c64ef80b51) did not do that.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With this patch the L2 cache is enabled on Canyonlands to increase the
overall performance. There is a known cache coherency issue with the L2
cache, but this is related to the high bandwidth (HB) PLB segment where
the memory address is 0x8.xxxx.xxxx (low bandwidth PLB segment is mapped
to 0x0.xxxx.xxxx). Since this HB address is currently unused it is safe
to enable the L2 cache.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The cuboot-acadia.c wrapper can cause assembler errors on some
toolchains due to the lack of the proper BOOTCFLAGS. This adds
the proper flags for the file.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds support for ISA memory holes on the PCI, PCI-X and
PCI-E busses of the 4xx platforms. The patch includes changes
to the Bamboo and Canyonlands device-trees to add such a hole,
others can be updated separately.
The ISA memory hole is an additional outbound window configured
in the bridge to generate PCI cycles in the low memory addresses,
thus allowing to access things such as the hard-decoded VGA
aperture at 0xa0000..0xbffff or other similar things. It's made
accessible to userspace via the new legacy_mem file in sysfs for
which support was added by a previous patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch creates the dts files for each core and splits the devices
between the two cores for MPC8572DS.
core0 has memory, L2, i2c, dma1, global-util, eth0, eth1, crypto, pci0, pci1.
core1 has L2, dma2, eth2, eth3, pci2, msi.
MPIC is shared between two cores but each core will protect its interrupts
from other core by using "protected-sources" of mpic.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also add NOR and NAND flash partitions for mpc8572ds board
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Basic support for the GPIO available on the SBC610 VPX Single Board Computer
from GE Fanuc (PowerPC MPC8641D).
This patch adds basic support for the GPIO in the devices I/O FPGA, the GPIO
functionality is exposed through the AFIX pins on the backplane, unless used
by an AFIX card.
This code currently does not support switching between totem-pole and
open-drain outputs (when used as outputs, GPIOs default to totem-pole).
The interrupt capabilites of the GPIO lines is also not currently supported.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adding use of newly added Epson RTX-8581 real-time clock driver to GE
Fanuc SBC610's dts file and adding driver to default config.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Just found the merge issue in 442746989d
("powerpc/83xx: Add support for MCU microcontroller in .dts files"):
the commit adds the MCU controller node into the DMA node, which is
wrong because the MCU sits on the I2C bus. Fix this by moving the MCU
node into the I2C controller node.
The original patch[1] was OK though. ;-)
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
ethernet0 (called FSL UEC0 in U-Boot) should be enet1 (UCC3/eth1), and
ethernet1 should be enet0 (UCC2/eth0), to be consistent with U-Boot so
that the interfaces do not swap addresses when control passes from
U-Boot to the kernel.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It's 1MB, not 512KB. Newer U-Boots will fix this entry, but that's no
reason to have the wrong value in the dts.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch corrects the bus-frequency value provided in the SBC610's dts.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
David Gibson suggested that since we are now unconditionally copying
the dtb into a malloc()ed buffer, it would be sensible to add a little
padding to the buffer at that point, so that further device tree
manipulations won't need to reallocate it.
This implements that suggestion.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We don't want to encourage the device_type usage. It isn't used in
the code, so we can simply remove it from the dts files.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit 91a0030295, plus
commit 0dcd440120 ("powerpc: Revert CHRP
boot wrapper to real-base = 12MB on 32-bit") which depended on it.
Commit 91a00302 was causing NVRAM corruption on some pSeries machines,
for as-yet unknown reasons, so this reverts it until the cause is
identified.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix format string warning in arch/powerpc/boot/main.c. Also correct
a typo ("uncomressed") on the same line.
BOOTCC arch/powerpc/boot/main.o
arch/powerpc/boot/main.c: In function 'prep_kernel':
arch/powerpc/boot/main.c:65: warning: format '%08x' expects type
'unsigned int', but argument 3 has type 'long unsigned int'
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's currently an off-by-one bug in fdt_subnode_offset_namelen()
which causes it to keep searching after it's finished the subnodes of
the given parent, and into the subnodes of siblings of the original
node which come after it in the tree. This bug was introduced in
commit ed95d7450d ("powerpc: Update
in-kernel dtc and libfdt to version 1.2.0").
A patch has already been submitted to dtc/libfdt mainline. We don't
really want to pull in a new upstream version during the 2.6.28 cycle,
but we should still fix this bug, hence this standalone version of the
fix for the in-kernel libfdt.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some platforms have variants that can share most of a flat device tree but need
a few devices selectively pruned at boot time. This adds del_node() to ops.h
to allow access to the existing fdt_del_node().
Signed-off-by: Mike Ditto <mditto@consentry.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The RTC is sitting on the I2C2 bus at address 0x68. RTC interrupt signal
is connected to the IPIC's EXT2 interrupt line, the line is shared with
Vitesse 8201 Ethernet PHY.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MCU is an external Freescale MC9S08QG8 microcontroller, mainly used to
provide soft power-off function, but also exports two GPIOs (wired to
the LEDs and also available from the external headers).
Added the MCU on mpc8349emitx, mpc837xrdb and mpc8315erdb boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Change the top-level #address-cells and #size-cells to <2> so the
mpc8572ds.dts is easier to deal with both a true 32-bit physical
or 36-bit physical address space.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We don't want to encourage the bogus device_type usage.
The device type isn't used in the code, so we can simply remove it from
the documentation and dts files.
Boards should specify proper compatible entries instead.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 9b09c6d909 ("powerpc: Change the
default link address for pSeries zImage kernels") changed the
real-base value in the CHRP note added by addnote to the zImage from
12MB to 32MB. It turns out that this causes unnecessary extra reboots
on old 32-bit CHRP machines. This therefore adds a -r flag to addnote
to allow us to specify what real-base value it should put in the CHRP
note, and adjusts the wrapper script to pass -r c00000 to addnote when
making a zImage for a CHRP machine. Also, CHRP machines ignore the
RPA note, so we don't need to arrange for it to be the same as the
kernel's.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This target is needed to build cuImages with an embedded ramdisk image.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I noticed, when trying to use, e.g.,
node = find_node_by_prop_value(prev, "booleanprop", "", 0))
to search for all nodes with a certain boolean property, that memcmp()
returns garbage when comparing zero bytes. It should return zero.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If the vmlinux binary in memory is larger than 4 MiB than it collides
with the initial boot code which is linked at 4 MiB in case of cuBoot.
If the the uncompressed image size (on disk size) is less than 4 MiB
then it would fit. The difference between those two sizes is the bss
section. In cuBoot we have the dtb embedded right after the data
section so it is very likely that the reset of the bss section (in
kernel's start up code) will overwrite the dtb blob. Therefore we
reallocate the dtb. Something similar is allready done to the initrd.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adds support for a HCU4 PPC405GPr based board from Netstal Maschinen AG.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds a cuboot wrapper for the AMCC PowerPC 405EZ Acadia board. The
clocking code is derived from U-Boot, originally written by Stefan Roese.
Signed-off-by: Josh Boyer <jwboyer@linux.ibm.com>
Add the base DTS for the AMCC PowerPC 405EZ Acadia evalution board.
In addition to some of the normal PPC 40x peripherals, the Acadia
board has:
- 64 MiB PSRAM
- NOR and NAND flash
- Two USB 1.1 host ports
- Two CAN 2.0 ports
- ADC and DAC connectors
- LCD display
This adds the basic platform support to build from.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Current device trees do not have the device_type = soc property set
anymore. Fix up the cuImage bootwrapper fragment to still find the IMMR
nodes.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The StMicro NAND chip (512Mbit, 64MB) is connected to the local bus,
the first local bus' user-programmable machine is configured by the
firmware to work with NAND chips.
QE GPIO pin is used to poll the NAND's Ready-Not-Busy signal.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This patch adds support for the registers held in the devices main FPGA,
exposing extra information about the revision of the board through cpuinfo.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale Elo DMA driver binds to all DMA channels in the device tree that
are compatible with "fsl,eloplus-dma-channel". This conflicts with the sound
drivers for the MPC8610 HPCD. On this board, the SSI uses two DMA channels and
therefore those channels are not available for general purpose use. We
change the compatible properties for these channels "fsl,ssi-dma-channel".
This works because the sound drivers don't actually check the compatible
property when it grabs channels.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The RTC is sitting on the I2C1 bus at address 0x68. RTC interrupt signal
is connected to the IPIC's EXT3 interrupt line.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Uses mpc83xx_add_bridge in fsl_pci.c
Adds second register tuple to pci node register property
as done for 83xx device trees in a previous patch.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Modify mpc83xx_add_bridge to get config space register base address from
the device tree instead of immr + hardcoded offset.
83xx pci nodes have this change:
register properties now contain two address length tuples:
First is the pci bridge register base, this has always been there.
Second is the config base, this is new.
This is documented in dts-bindings/fsl/83xx-512x-pci.txt
The changes accomplish these things:
mpc83xx_add_bridge no longer needs to call get_immrbase
it uses hard coded addresses if the second register value is missing
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D).
A number of MPC8641D based route interrupts for on-board interrupts through
a FPGA based interrupt controller, which is chained with the
MPC8641D's mpic. This patch provides a basic driver to allow basic routing
of interrupts to the mpic.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 9b09c6d909 ("powerpc: Change the
default link address for pSeries zImage kernels") changed the
real-base value in the CHRP note added by the addnote program from
12MB to 32MB to give more space for Open Firmware to load the zImage.
(The real-base value says where we want OF to position itself in
memory.) However, this change was ineffective on most pSeries
machines, because the RPA note added by addnote has the "ignore me"
flag set to 1. This was intended to tell OF to ignore just the RPA
note, but has the side effect of also making OF ignore the CHRP note
(at least on most pSeries machines).
To solve this we have to set the "ignore me" flag to 0 in the RPA
note. (We can't just omit the RPA note because that is equivalent to
having an RPA note with default values, and the default values are not
what we want.) However, then we have to make sure the values in the
zImage's RPA note match up with the values that the kernel supplies
later in prom_init.c with either the ibm,client-architecture-support
call or the process-elf-header call in prom_send_capabilities().
So this sets the "ignore me" flag in the RPA note in addnote to 0, and
adjusts the RPA note values in addnote.c and in prom_init.c to be
consistent with each other and with the values in ibm_architecture_vec.
However, since the wrapper is independent of the kernel, this doesn't
ensure that the notes will stay consistent. To ensure that, this adds
code to addnote.c so that it can extract the kernel's RPA note from
the kernel binary and put that in the zImage. To that end, we put the
kernel's fake ELF header (which contains the kernel's RPA note) into
its own section, and arrange for wrapper to pull out that section with
objcopy and pass it to addnote, which then extracts the RPA note from
it and transfers it to the zImage.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PCI bridge on the Holly board is incorrectly represented in the
device tree. The current device tree node for the PCI bridge sits
under the tsi-bridge node. That's not obviously wrong, but the PCI
bridge translates some PCI spaces into CPU address ranges which were
not translated by the "ranges" property in tsi-bridge node.
We used to get away with this problem because the PCI bridge discovery
code was also buggy, assuming incorrectly that PCI host bridge nodes
were always directly under the root bus and treating the translated
addresses as raw CPU addresses, rather than parent bus addresses.
This has since been fixed, thus breaking Holly.
This could be fixed by adding extra translations to the tsi-bridge
node, but this patch instead moves the Holly PCI bridge out of the
tsi-bridge node to the root bus. This makes the tsi-bridge node
represent only the built-in IO devices in the bridge, with a
more-or-less contiguous address range. This is the same convention
used on Freescale SoC chips, where the "soc" node represents only the
IMMR region, and the PCI and other bus bridges are separate nodes
under the root bus.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add the fsl,playback-dma and fsl,capture-dma properties to the Freescale
MPC8610 HPCD device tree. These properties connect the SSI nodes to the
DMA nodes for the DMA channels that the SSI should use. Also update the
ssi.txt documentation.
These properties will be needed when the ASoC V2 version of the Freescale
MPC8610 device drivers are merged into the mainline.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
One of the changes in the bootwrapper makefile introduced the dtbImage
targets for boards that need a simple zImage with a DTB embedded in
them (595be948cc, "[POWERPC]
bootwrapper: Build multiple cuImages"). When this was done, it broke
booting on the Holly board as the zImage.holly wrapper did not get the
DTB embedded properly.
This changes the target for the Holly board to a dtbImage so that the
wrapper includes the vmlinux, wrapper bits, and DTB.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For Freescale 8xxx devices that use an MPIC, the interrupt numbers in
the device tree must be 16 greater than the values documented in the
reference manual. In these chips, the MPIC is wired to use the first
16 numbers for external interrupts, but the documentation numbers
internal interrupts from 0.
In the MPC8610 HPCD device tree, the interrupt properties for the DMA
channels for DMA2 were not the adjusted values. This fixes that.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the basic board support for GE Fanuc's SBC610, a 6U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds the localbus node, moves the bcsr node into the
localbus node, and adds the flash node.
Also enable MTD support in the defconfig.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This implements CONFIG_RELOCATABLE for 64-bit by making the kernel as
a position-independent executable (PIE) when it is set. This involves
processing the dynamic relocations in the image in the early stages of
booting, even if the kernel is being run at the address it is linked at,
since the linker does not necessarily fill in words in the image for
which there are dynamic relocations. (In fact the linker does fill in
such words for 64-bit executables, though not for 32-bit executables,
so in principle we could avoid calling relocate() entirely when we're
running a 64-bit kernel at the linked address.)
The dynamic relocations are processed by a new function relocate(addr),
where the addr parameter is the virtual address where the image will be
run. In fact we call it twice; once before calling prom_init, and again
when starting the main kernel. This means that reloc_offset() returns
0 in prom_init (since it has been relocated to the address it is running
at), which necessitated a few adjustments.
This also changes __va and __pa to use an equivalent definition that is
simpler. With the relocatable kernel, PAGE_OFFSET and MEMORY_START are
constants (for 64-bit) whereas PHYSICAL_START is a variable (and
KERNELBASE ideally should be too, but isn't yet).
With this, relocatable kernels still copy themselves down to physical
address 0 and run there.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Anton Vorontsov
Grzegorz Bernacki
Grant Likely
Reynes Philippe
Wolfgang Grandegger
Martyn Welch
Benjamin Herrenschmidt
Li Yang
Kumar Gala
Sean MacLennan
Grant Erickson
Linus Torvalds
Vitaly Bordug
Nick Andrew
Becky Bruce
Benjamin Krill
Scott Wood
Paul Mackerras
Andy Fleming
Stefan Roese
Josh Boyer
Haiying Wang
Michael Barkowski
Trent Piepho
Sebastian Siewior
Jon Smirl
David Gibson
Mike Dyer
Mike Ditto
Ed Swarthout
Jason Jin
Niklaus Giger
Timur Tabi
John Rigby
Victor Gallardo
Heiko Schocher