Like for the TQM5200, the vendor prefix "tqc," is now used for all
TQM85xx modules from TQ-Components GmbH (http://www.tqc.de) in the
corresponding DTS files.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MDIO-less PHYs should use CONFIG_FIXED_PHY driver and appropriate
fixed-link property in the device tree.
If not, ethernet will not work:
e0024520:03 not found
eth1: Could not attach to PHY
IP-Config: Failed to open eth1
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Andrew Klossner pointed out the IO space size was in violation of
the alignment requirements for windows on the 85xx. The size should
have been 1M (to match u-boot).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).
Part 2 of 5: support for the board in arch/powerpc/boot.
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).
Part 1 of 5: DTS file describing the board peripherals. As far as I
know all peripherals except the FPGA are listed in there (I did not
include the FPGA because a lot of work is needed there).
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This corrects the names of two CONFIG_ variables.
Note that the CONFIG_MPC86XADS fix uncovers another bug
(with mpc866_ads_defconfig) that will require fixing:
<-- snip -->
...
arch/powerpc/boot/dtc -O dtb -o arch/powerpc/boot/mpc866ads.dtb -b 0 /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/dts/mpc866ads.dts
DTC: dts->dtb on file "/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/dts/mpc866ads.dts"
WRAP arch/powerpc/boot/cuImage.mpc866ads
powerpc64-linux-ld: arch/powerpc/boot/cuboot-mpc866ads.o: No such file: No such file or directory
make[2]: *** [arch/powerpc/boot/cuImage.mpc866ads] Error 1
<-- snip -->
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Added next-level-cache to the L1 and a reference to the new L2 label.
This is per the ePAPR 0.94 spec. Since we are't really dependent on this
today we aren't supporting the "legacy" l2-cache phandle that is specified
in the PPC v2.1 OF Binding spec.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed clock-frequency, big-endian, and built-in props as they aren't
specified anywhere. Also added compatible = "chrp,open-pic" in the
places it was missing.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following adds support for the Analogue & Micro ASP 8347E, running
Redboot.
http://www.analogue-micro.com/ASP8347.html
Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch enabled MSI on 8544ds and 8572ds board.
So far only one MSI interrupt can generate on 8544 board.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch enable the MSI on 8610hpcd board.
Through the msi-available-ranges property, All the 256
msi interrupts can be tested on this board.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The node for DMA2 in the MPC8610 HPCD device tree has the wrong compatible
properties. This breaks the DMA driver and the sound driver.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Switched from 64M NOR/64M NAND to 4M NOR/256M NAND.
* Full DTM support including critical temperature.
* Added POST information.
* Removed LED function, moved to new LED driver.
* Moved ad7414 to new style I2C initialization.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This fixes the PCI node in the Rainier to match the spec from AMCC. A
similar fix was done for 440EPx, which shares the same values as 440GRx.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
At the moment we have a mixture of left-over version 0 and new-format
version 1 files in arch/powerpc/boot/dts. This is potentially
confusing to people new to the dts format attempting to figure it out.
So, this patch converts all the as-yet unconverted dts v0 files and
converts them to v1. They're mechanically-converted, and not hand
tweaked so in some cases they're not 100% in keeping with usual v1
style, but the convertor program does have some heuristics so the
discrepancies aren't too bad.
I have checked that this patch produces no changes to the resulting
dtb binaries.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
dtbImage.* and several zImage. targets get created but never cleaned up.
Also, moved zImage to the clean-files line associated with all other image
results (was previously duplicated).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PowerPC 440EP, 440GR, 440EPx, and 440GRx chips have an issue that
causes the PLB3-to-PLB4 bridge to wait indefinitely for transaction
requests that cross the end-of-memory-range boundary. Since the DDR
controller only returns the valid portion of a read request, the bridge
will prevent other PLB masters from completing their transactions.
This implements the recommended workaround for this errata for chips that
use older versions of firmware that do not already handle it. The last
4KiB of memory are hidden from the kernel to prevent the problem
transactions from occurring.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The following adds local bus, flash and MTD partition nodes for
sbc8548. As well, a compatible field for the soc node, so that
of_platform_bus_probe() will pick it up.
Something that is provided through this newly added epld node
is the Hardware Revision which is now being utilized.
Signed-off-by: Jeremy McNicoll <jeremy.mcnicoll@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Cc: "Nelson, Shannon" <shannon.nelson@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds device tree nodes for NOR and NAND flashes and places
board-control node inside the localbus.
defconfig and board file updated appropriately.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch is fixes the sequoia.dts device tree file to use the values defined
in the 440Epx data sheet from AMCC.
That fixes an issue where some devices, including graphics cards, would not
initialize properly because the PCI resource space was not big enough.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds pcie node which is resposible for PCI-E x8 slot
functioning. Though, this was tested using only x1 SKY2 NIC.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add board support for the Phytec pcm030 mpc5200b based board. It
does not need any platform specific fixups and as such is handled
as a mpc5200 simple platform.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds properties describing the RapidIO controller to the
device-tree source for the MPC8641HPCN board.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following features are supported:
plane 0 works as a regular frame buffer, can be accessed by /dev/fb0
plane 1 has two AOIs (area of interest), can be accessed by /dev/fb1 and /dev/fb2
plane 2 has two AOIs, can be accessed by /dev/fb3 and /dev/fb4
Special ioctls support AOIs
All /dev/fb* can be used as regular frame buffer devices, except hardware
change can only be made through /dev/fb0. Changing pixel clock has no effect
on other fbs.
Limitation of usage of AOIs:
AOIs on the same plane can not be horizonally overlapped
AOIs have horizonal order, i.e. AOI0 should be always on top of AOI1
AOIs can not beyond phisical display area. Application should check AOI geometry
before changing physical resolution on /dev/fb0
required command line parameters to preallocate memory for frame buffer diufb.
optional command line parameters to set modes and monitor
video=fslfb:[resolution][,bpp][,monitor]
Syntax:
Resolution
xres x yres-bpp@refresh_rate, the -bpp and @refresh_rate are optional
eg, 1024x768, 1280x1024, 1280x1024-32, 1280x1024@60, 1280x1024-32@60, 1280x480-32@60
Bpp
bpp=32, bpp=24, or bpp=16
Monitor
monitor=0, monitor=1, monitor=2
0 is DVI
1 is Single link LVDS
2 is Double link LVDS
Note: switching monitor is a board feather, not DIU feather. MPC8610HPCD has three
monitor ports to swtich to. MPC5121ADS doesn't have additional monitor port. So switching
monirot port for MPC5121ADS has no effect.
If compiled as a module, it takes pamameters mode, bpp, monitor with the same syntax above.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
virtex405-head.S is an assembler file, not a C file; therefore BOOTAFLAGS
is the correct place to set the needed -mcpu=405 flag.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds default NOR entries to the AMCC Canyonlands (460EX)
and Glacier (460GT) dts files.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The Xilinx 16550 uart core is not a standard 16550 because it uses
word-based addressing rather than byte-based adressing. With
additional properties it is compatible with the open firmware
'ns16550' compatible binding.
This code updates the ns16550 driver to use the reg-offset property
so that the Xilinx UART 16550 can be used with it. The reg-shift
was already being handled.
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
MPC8568E has 64K byte MURAM, so the size should be 0x10000, not 0xc000.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cleanups as suggested by Stephen Rothwell and Dale Farnsworth, which
incudes marking a bunch of functions static and add a vendor prefix to
the compat node check for uniqueness.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* remove #cpus from mpc8544ds.dts (not used anywhere else)
* remove memreserve from mpc8568mds.dts (not needed)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds in the device tree source for the SBC8641D, based
largely on the mpc8641_hpcn.dts. The biggest differences are
the lack of a complex IRQ mapping (since no Uli/i8259 cascade)
and the different layout of devices on the localbus node.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
1. Detect (and bail out on) more conditions that violate the
assumptions of the setup code -- we assume in such cases that the device
tree is correct and reflects what the firmware did.
2. The inbound memory mask calculation was wrong.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- get rid of `model = "UCC"' in the ucc nodes
It isn't used anywhere, so remove it. If we'll ever need something
like this, we'll use compatible property instead.
- replace last occurrences of device-id with cell-index.
Drivers are modified for backward compatibility's sake.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch modifies the Embedded Planet EP8248E device tree to reference the
SMC paramater RAM base register instead of the parameter RAM allocated by the
boot loader.
The cpm_uart driver will allocate parameter RAM itself, making the serial port
initialisation independent of the boot loader.
The patch adds the parameter RAM allocated by the boot loader in the CPM muram
node, making it available to the kernel.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch relocates the buffer descriptors and the SMC parameter RAM at the
end of the first CPM muram chunk, as described in the device tree. This allows
device trees to stop excluding SMC parameter ram allocated by the boot loader
from the CPM muram node.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds a new generic device tree processing function that retrieves
virtual reg addresses from the device tree to the bootwrapper code. It also
updates the bootwrapper code to use the new function.
dt_get_virtual_reg() retrieves the virtual reg addresses from the
"virtual-reg" property. If the property can't be found, it uses the "reg"
property and walks the tree to translate it to absolute addresses.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the device tree node for the DMA engine on 8544, publish
the device and enable the driver in the defconfig.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that we properly set the physical address in the program header of the
vmlinux ELF we can extract it to properly set the load and entry point for
u-boot uImages. Before we always hard coded the load & entry point to 0.
However there are situations that the kernel may be built with a non-zero
physical address.
We use objdump to extract the PHDR. We assume that there is only one
PHDR in the vmlinux of type LOAD.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The prpmc2800 platform requires a zImage formatted file with an
embedded dtb file. Rename the requested boot image file to
dtbImage.prpmc2800.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The mv643xx_eth driver is being modified to support multiple instances
of the ethernet silicon block on the same platform. Each block contains
a single register bank containing the registers for up to three ports
interleaved within that bank. This patch updates the PowerPC OF to
platform_device glue code to support multiple silicon blocks, each
with up to three ethernet ports. The main difference is that we now
allow multiple mv64x60_shared platform_devices to be registered and
we provide each port platform_device with a pointer to its associated
shared platform_device. The pointer will not be used until the
mv643xx_eth driver changes are committed.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove several unused (or software config only) properties.
Rename marvel node to "system-controller". Also, rename the
"block-index" property to "cell-index" to conform to current
practice.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace several device node absolute path lookups in the mv64x60
bootwrapper code with lookups by compatible or device_type
properties.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Compatible names should refer to a specific version of the hardware,
without wildcards. Change each instance of mv64x60 to mv64360, which
is the oldest version we currently support.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
After the conversion to dts v1 format, seeing the frequencies
in decimal made it obvious that some of them had been
incorrectly truncated. This fixes them. Note that the PCI
frequency comes from a different source and is documented
as 66MHz, so it was left at 66000000.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update the prpmc2800 DTS file to version 1 and add labels.
I verified that there was no change in the resulting dtb file.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch changes the "max-frame-size" property to 9000 for all gbit
enabled 4xx boards. All those ports generally support jumbo frames, so
let's give the user a chance to enable it.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch fixes some problems in the Canyonlands 460EX and Glacier 460GT
dts files:
- Add "mdio-device = <&EMAC0>" to all all EMAC's except for EMAC0 itself
(the 460EX/GT only can access the PHY via the EMAC0 instance)
- Add TAH support to Canyonlands dts
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This gets the FEC ethernet driver working again on the lite5200
platform.
The FEC driver is also compatible with the MPC5200, not only with the
MPC5200B, so this adds a suitable entry to the driver's match list.
Furthermore this adds the settings for the PHY in the dts file for the
Lite5200. Note, that this is not exactly the same as in the
Lite5200B, because the PHY is located at f0003000:01 for the 5200, and
at :00 for the 5200B. This was tested on a Lite5200 and a Lite5200B,
both booted a kernel via tftp and mounted the root via nfs
successfully.
Signed-off-by: René Bürgel <r.buergel@unicontrol.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This target produces a flat binary rather than an ELF file,
fixes the entry point at the beginning of the image, and takes
a complete device tree with no fixups needed.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Call dtc from the Makefile instead of the wrapper script so that the dt
blobs can be generated with a simple make invocation.
Using this patch allows board ports to trigger automatic building of .dtb
files by adding them to the image-y target list.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Improve the debugging support of the PS3 bootwraper code:
o Increase the size of the PS3 bootwrapper overlay from 256 to 512 bytes to
allow for more debugging code in the overlay.
o Use the dot symbol to set the size of __system_reset_overlay. The
assembler will then emit an error if the overlay code is too big.
o Remove some unused instructions.
o Update the text describing the PS3 bootwrapper overlay.
o Add a check for null pointer writes.
o Change hcall return value from s64.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
as prescribed in Documentation/powerpc/booting-without-of.txt.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Due to chip constraint MPC837x USB DR module can only use
ULPI and serial PHY interfaces. The patch fixes the wrong
type in dts.
This patch fixes USB malfunctioning on the MPC837xE-RDB boards.
Similar patch has been already applied for the MDS boards:
commit 28b9588592
Author: Li Yang <leoli@freescale.com>
Date: Thu Mar 6 18:42:26 2008 +0800
[POWERPC] 83xx: Fix wrong USB phy type in mpc837xmds dts
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add device tree file for Emerson KSI8560 board.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add boot wrapper for Emerson KSI8560 board.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds the L2 cache node to the Taishan 440GX dts file.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Currently Haleakala uses the Kilauea platform code. This patch adds
"haleakala" to the compatible property, in case later kernel versions
will introduce a Haleakala platform code.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The patch adds the Glacier dts. The Glacier is nearly identical to the
Canyonlands (460EX). Here the differences:
- 4 ethernet ports instead of 2
- no SATA port
- no USB port
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds TAH (TCP/IP Acceleration Hardware) support to the
taishan 440GX dts. It depends on the NEWEMAC/tah patch that adds the
compatible "ibm,tah" property to the matching table.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This dts source file for the AMCC 460EX Canyonlands evalutaion board
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch alters the bootwrapper for a number of machines (roubhly
all 4xx based cuboot or treeboot platforms) to use aliases instead of
the linux,network-index hack to work out which MAC address to attach
to which ethernet device node.
The now obsolete linux,network-index properties are removed from the
corresponding device trees. This won't break backwards compatiblity,
because in cases where this fixup code is relevant, the device tree is
part of the kernel image.
The references to linux,network-index are removed from
booting-without-of.txt. Not only is it now deprecated, but as a hack
applicable only when the device tree blob and fixup code were in the
same image, this property never belonged in booting-without-of.txt
which describes the interface between the kernel and firmware or
bootloaders which produce a device tree. By the time the device tree
reaches the kernel, all the MAC addresses must be fully filled in.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The MDIO node in the lite5200b.dts file needs to also claim compatibility
with the older mpc5200 chip. Otherwise the driver won't find the device.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The wrapper script didn't have entries for the TQM8540 board and the
SBC8548 or SBC8560 boards. I've assumed that the TQM8540 console is
8250 based and not CPM based by looking at its defconfig. There was
also a trailing * on the TQM8555 entry that I removed too.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The pattern substitution rules were failing when used with zImage-dtb
targets. If zImage-dtb.initrd was selected, the pattern substitution
would generate "zImage.initrd-dtb" instead of "zImage-dtb.initrd" which
caused the build to fail.
This renames zImage-dtb to dtbImage to avoid the problem entirely.
By not using the zImage prefix then is no potential for namespace
collisions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following patch allows interrupts to occur on the
sbc8548. Currently PCI and PCI-X devices get assigned an IRQ
but the interrupt count never increases. This solves the
problem and adds PCI support as well.
Signed-off-by: Jeremy McNicoll <jeremy.mcnicoll@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This fixes the following bug:
http://ozlabs.org/pipermail/linuxppc-dev/2008-February/051979.html
Separate defconfigs are no longer needed now that CONFIG_DEVICE_TREE is gone.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Due to chip constraint MPC837x USB DR module can only use
ULPI and serial PHY interfaces. The patch fixes the wrong
type in dts.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Correct the remaining 44x cuboot wrappers to define TARGET_4xx as well. This
creates the correct structure to use, including things like the second MAC
address.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
In order to get the proper boad info (bd_info) structure defined in ppcboot.h
both TARGET_4xx and TARGET_44x should be defined for all PowerPC 440 boards.
The 440GX boards also need TARGET_440GX defined since they have 4 EMACs and
there are 4 MAC addesses in bd_info passed by u-boot.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch changes the katmai (440SPe) L1 cache size to 32k. Some
whitespace issues are cleaned up too.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Since the 4xx PCIe driver checks for 405ex compatibility, the
PCIe interface was not detected as it is currently defined as
"405exr" compatible. This patch changes it to "405ex".
The 405EX and 405EXr are identical exept that the 2nd PCIe and the
2nd EMAC interfaces are missing.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
GCC versions before 3.4 did not support the -mcpu=440 option. Use
-mcpu=405 for the 4xx specific bootwrapper files, as that has been
around for much longer.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove all "i2c" and "xxmii-interface" (rgmii etc) device_type entries
from the 4xx dts files.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Fix a bug in the lv1_get_repository_node_value() routine of the PS3
bootwrapper. Changes in the PS3 system firmware 2.20 cause this bug
to hang the system when branching from the bootwrapper to the kernel
_start.
Since the video system has not yet been enabled at the time
the bug is hit, the system hangs with a blank screen. Earlier
firmwares don't cause such a catastrophic failure, and so this
bug went undetected.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, the kernel uses CONFIG_DEVICE_TREE to wrap a kernel image
with a fdt blob which means for any given configuration only one dts
file can be selected and so support for only one board can be built
This moves the selection of the default .dts file out of the kernel
config and into the bootwrapper makefile. The makefile chooses which
images to build based on the kernel config and the dts source file
name is taken directly from the image name. For example "cuImage.ebony"
will use "ebony.dts" as the device tree source file.
In addition, this patch allows a specific image to be requested from the
command line by adding "cuImage.%" and "treeImage.%" targets to the list
of valid built targets in arch/powerpc/Makefile. This allows the default
dts selection to be overridden.
Another advantage to this change is it allows a single defconfig to be
supplied for all boards using the same chip family and only differing in
the device tree.
Important note: This patch adds two new zImage targets; zImage.dtb.% and
zImage.dtb.initrd.% for zImages with embedded dtb files. Currently
there are 5 platforms which require this: ps3, ep405, mpc885ads, ep88xc,
adder875-redboot and ep8248e. This patch *changes the zImage filenames*
for those platforms. ie. 'zImage.ps3' is now 'zImage.dtb.ps3'.
This new zImage.dtb targets were added so that the .dts file could be
part of the dependancies list for building them.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Minimal /dts-v1/ device tree for mpc5121 ads.
port-number property in uart nodes
will go away after the driver learns to use aliases
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cleaned up IRQ layout and removed unsused ISU allocations.
Fixed RTC address typo from /dts-v1/ conversion.
Incorporated list suggestions to use an "iomega," vendor prefix,
and to use a node reference rather than a hard path.
Signed-off-by: Jon Loeliger <jdl@@jdl.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
cpm_uart_core has a dependency on fsl,cpm-brg/clock-frequency, this
means that a .dts that uses the cpm uart driver needs to supply a
clock-frequency entry for get_brgfreq to return a meaningful number.
Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The 8313 rdb has a ds1339 at address 0x68.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
According to the 8349EA ref man, the second PCI PHB IRQ is 67. Thanks to Peter
Van Ackeren for finding this.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SCCR USB bits are in a different location on the mpc8315.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the deprecated __attribute_used__.
[Introduce __section in a few places to silence checkpatch /sam]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch converts the remaining 83xx boards to the dts-v1 format.
This includes the mpc8313_rdb, mpc832x_mds, mpc8323_rdb, mpc8349emitx,
mpc8349emitxgp and the mpc836x_mds.
The mpc8315_rdb mpc834x_mds, mpc837[789]_*, and sbc8349 were already
dts-v1 and only undergo minor changes for the sake of formatting
consistency across the whole group of boards; i.e. the idea being
that you can do a "diff -u board_A.dts board_B.dts" and see something
meaningful.
The general rule I've applied is that entries for values normally
parsed by humans are left in decimal (i.e. IRQ, cache size, clock
rates, basic counts and indexes) and all other data (i.e. reg and
ranges, IRQ flags etc.) remain in hex.
I've used dtc to confirm that the output prior to this changeset
matches the output after this changeset is applied for all boards.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently there are several dts that don't specify address or size
cells for the muram. This causes dtc to use default values, one of
which is an address-cells of two, and this breaks the parsing of the
muram ranges, which is assuming an address-cells of one. For example:
Warning (reg_format): "reg" property in
/qe@e0100000/muram@10000/data-only@0 has invalid length
(8 bytes) (#address-cells == 2, #size-cells == 1)
Explicitly setting the address and size cells gets it parsed properly
and gets rid of the four dtc warnings.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the dts files for the MPC838xE Reference Development Board (RDB).
The board is a mini-ITX reference board with 256M DDR2, 8M flash,
32M NAND, USB, PCI, gigabit ethernet, SATA, and serial.
the difference among the three files is the 8377 has two, the 8378
none, and the 8379 has four sata controllers.
partially based on the 8379 mds device trees.
Signed-off-by: Joe D'Abbraccio <ljd015@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the dts for the MPC8315E Reference Development Board (RDB).
The board is a mini-ITX reference board with 128M DDR2, 8M flash,
32M NAND, USB, PCI, gigabit ethernet, SATA, and serial.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also:
- rename "fsl_spi" to "fsl,spi";
- add and use cell-index property, if found;
- split probing code out of fsl_spi_init, thus we can call
it for legacy device_type probing and new "compatible" probing.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
device_type property is bogus, thus use proper compatible.
Also change compatible property to "fsl,ucc-mdio".
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now we're searching for "fsl,qe", "fsl,qe-muram", "fsl,qe-muram-data"
and "fsl,qe-ic".
Unfortunately it's still impossible to remove device_type = "qe"
from the existing device trees because older u-boots are looking for it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* "simple-bus" covers all our needs for of_platform_bus_probe()
* make device tree name just 'soc' not 'soc85..'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move mpc834x_mds device tree source forward to dts-v1 format. Nothing
too complex in this one, so it boils down to just adding a bunch of 0x
in the right places and converting clock speeds to decimal.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds the device tree source for the Wind River SBC834x board.
It is based on the MPC834x_MDS DTS, with the biggest difference being
the lack of BCSR and the PCI2 that the MDS gets via the PIB. That,
and this file is also dts-v1 format.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds a v1 device tree source for the Wind River SBC8548 board.
The biggest difference between this and the MPC8548CDS reference
platform is the absence of the CDS's Arcadia peripherals and physical
access to the PCI#2 bus.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds a v1 device tree source for the Wind River SBC8560 board. The
biggest difference between this and the MPC8560ADS reference platform
dts is the use of an external 16550 compatible UART instead of the CPM2.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to find a device node by just what its compatible with.
This is useful in cases that we don't have a prop to find the node with.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The various 5200 dts files don't have values specified for the soc
node, which in turn results in a warning from the processing of
every child node (roughly 40 warnings per file). This explicitly
sets the default values and gets rid of all the warnings.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add the cuboot wrapper for the PIKA Warp board
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add the device tree for the PIKA Warp board
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch extends the Ebony and Walnut platform code to instantiate
the existing ds1742 RTC class driver for the DS1743 RTC/NVRAM chip
found on both those boards. The patch uses a helper function to scan
the device tree and instantiate the appropriate platform_device based
on it, so it should be easy to extend for other boards which have mmio
mapped RTC chips.
Along with this, the device tree binding for the ds1743 chips is
tweaked, based on the existing DS1385 OF binding found at:
http://playground.sun.com/1275/proposals/Closed/Remanded/Accepted/346-it.txt
Although that document covers the NVRAM portion of the chip, whereas
here we're interested in the RTC portion, so it's not entirely clear
if that's a good model.
This implements only RTC class driver support - that is /dev/rtc0, not
/dev/rtc, and the low-level get/set time callbacks remain
unimplemented. That means in order to get at the clock you will
either need a modified version of hwclock which will look at
/dev/rtc0, or you'll need to configure udev to symlink rtc0 to rtc.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The patch adds the Haleakala dts. The Haleakala is a stripped down
version of the Kilauea (405EX) with only one EMAC and only one PCIe
interface.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Use cuImage bootwrapper until U-Boot port is completed.
Derived heavily from Linkstation port.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Wilcox <andy@protium.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Based on the Kurobox DTS files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Wilcox <andy@protium.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add local bus, flash, and MTD partition nodes to mpc8641_hpcn.dts
Also add compatible field for the soc node, so that it will be picked up
by of_platform_bus_probe().
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add NAND to device tree, and call of_platform_bus_probe().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This board is also resold by Freescale under the names
"QUICCStart MPC8248 Evaluation System" and "CWH-PPC-8248N-VE".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update the MPC8610 HPCD files to support the audio driver. Update
booting-without-of.txt with information on the SSI device.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for UART serial ports using a Freescale QUICCEngine. Update
booting-without-of.txt to define new properties for a QE UART node. Update
the MPC8323E-MDS device tree to add UCC5 as a UART. Update the QE library
to support slow UCC devices and modules.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
...thus use fixed-link to register proper "Fixed PHY"
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds localbus and pata nodes to use CF IDE interface
on MPC8349E-mITX boards.
Patch also adds code to probe localbus.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove device_type = "usb" for 83xx SoC USB controller
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The ULI based boards had the interrupt maps for USB on the ULI incorrectly
set.
Also, the MPC8572DS was missing the interrupt-map-mask for the 3rd PCIe
controller.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to set the mac address given the alias for the device.
Removes the need for having a linux,network-index property.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix typo in arch/powerpc/boot/flatdevtree_env.h.
There is no Documentation/networking/ixgbe.txt.
README.cycladesZ is now in Documentation/.
wavelan.p.h is now in drivers/net/wireless/.
HFS.txt is now Documentation/filesystems/hfs.txt.
OSS-files are now in sound/oss/.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for 'mpc5200-simple-platform' compatible
boards which do not need a platform specific setup. Such boards
are supported assuming the following:
- GPIO pins are configured by the firmware,
- CDM configuration (clocking) is setup correctly by firmware,
- if the 'fsl,has-wdt' property is present in one of the
gpt nodes, then it is safe to use such gpt to reset the board,
- PCI is supported if enabled in the kernel configuration
and if there is a PCI bus node defined in the device tree.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add device tree source file for Promess Motion-PRO board.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add device tree source file for CM5200 board.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add device tree source file for TQ Components TQM5200 board.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Update .gitignore as needed by dtc addition.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Missed this one in the boot loader before.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds support for 405GPr processors with optional
new mode strapping. ibm405gp_fixup_clocks() can now be used
for 405GP and 405GPr CPUs.
This is in preparation of porting the cpci405 platform support
from arch/ppc to arch/powerpc.
This patch also adds ibm405ep_fixup_clocks() to support
405EP CPUs from the boot wrapper.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Currently we have some limitations in the 4xx PCIe driver and can't
support all possible PCIe busses. But the current limits in the
dts file are quite low (only 16 busses per RC). This patch increases
the number to 64 per RC.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Recent DTC versions disallow certain special characters in full paths without
being quoted with {}. That however breaks compatibility with older DTC
versions. Work around this by renaming the CPU nodes for the 4xx files to a
generic node name, and specify the processor type in the model property of the
CPU node.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The recent changes from Benjamin Herrenschmidt to the ibm_newemac now
make it possible to support other 4xx variants by just defining the
correct properties in the device tree. In this case of the 405EX we
need to define "has-mdio" in the RGMII node and "has-inverted-stacr-oc"
and "has-new-stacr-staopc" in the EMAC node same as on the 440EPx.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds runtime detection of the 440SPe revision A chips. These
chips are equipped with a slighly different PCIe core and need special/
different initialization. The compatible node is changed to
"plb-pciex-440spe" ("A" and "B" dropped). This is needed for boards that
can be equipped with both PPC revisions like the AMCC Yucca.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This removes a bogus empty "ranges" property in the EBC device node
of the Bamboo board device-tree.
The "ranges" property should be created by the wrapper code when it is
implemented. Until then, remove the empty property since it incorrectly
implies that there is a 1:1 address mapping between the EBC and the OPB.
This also fixes a warning from newer DTCs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds base support for the Katmai board, including PCI-X and
PCI-Express (but no RTC, nvram, etc... yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This reworks the boot wrapper library function that probes
the chip clocks. Better separate the base function that is
used on 440GX,SPe,EP,... from the uart fixups as those need
different device-tree path on different processors.
Also, rework the function itself based on the arch/ppc code
from Eugene Surovegin which I find more readable, and which
handles one more bypass case. Also handle the subtle difference
between 440EP/EPx and 440SPe/GX, on the former, PerClk is derived
from the PLB clock while on the later, it's derived from the OPB.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds macros to the boot wrapper to access the CPR
registers from the boot wrappers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The 4xx bootwrapper occasionally needs to access SPR registers,
this adds mfspr/mtspr wrappers to it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds a function to the bootwrapper 4xx library to decode memory
size on 440SPE processors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds the definition of the on-chip OHCI controller to the
Bamboo board's device-tree. This is enough to get it probed and
working, though a separate patch fixing a bug in the OHCI driver
is needed to make it reliable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds the device-tree bits & call to ppc4xx_pci_find_bridges()
to make PCI work on the Bamboo board
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds base support for the AMCC Taishan 440GX evaluation
board.
Signed-off-by: Hugh Blemings <hugh@blemings.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This wires up the 4xx PCI support & device-tree bits for the
405GP based Walnut platform.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Brings EP405 support to arch/powerpc. The IRQ routing for the CPLD
comes from a device-tree property, PCI is working to the point where
I can see the video card, USB device, and south bridge.
This should work with both EP405 and EP405PC.
I've not totally figured out how IRQs are wired on this hardware
though, thus at this stage, expect only USB interrupts working,
pretty much the same as what arch/ppc did.
Also, the flash, nvram, rtc and temp control still have to be wired.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This wires up the 4xx PCI support & device tree bits for
440GP based Ebony platform.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch alters the kernel makefiles to build dtc from the sources
embedded in the previous patch. It also changes the
arch/powerpc/boot/wrapper script to use the embedded dtc, rather than
expecting a copy of dtc already installed on the system.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This incorporates a copy of dtc into the kernel source, in
arch/powerpc/boot/dtc-src. This commit only imports the upstream
sources verbatim, a later commit will actually link it into the kernel
Makefiles and use the embedded code during the kernel build.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Many operations, as currently used in the wrapper, assume they can
pass NULL and have it be treated as the root node. However, libfdt-wrapper
converts NULL to -1, which is only appropriate when searching for nodes,
and will cause an error otherwise.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
fdt_wrapper_create_node passes a variable called offset to offset_devp(),
which uses said parameter to initialize a local variable called offset.
Due to one of the odder aspects of the C language, the result is an
undefined variable, with no error or warning.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Updates the ucc_geth device driver to check the new rx-clock-name and
tx-clock-name properties first. If present, it uses the new function
qe_clock_source() to obtain the clock source. Otherwise, it checks the
deprecated rx-clock and tx-clock properties.
Update the device trees for 832x, 836x, and 8568 to contain the new property
names only.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Verified on mpc866ads. This version has muram and brg nodes added to dts
to get the things work.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Added aliases nodes for kurobox, 83xx, 85xx, and 86xx platforms.
This included added labels and cell-index properties for serial and
pci nodes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Removed address fields in ethernet nodes
* Removed #address-cells, #size-cells from gianfar nodes
* Added cell-index to gianfar and ucc ethernet nodes
* Added enet[0..3] labels
* Renamed compatible node for gianfar mdio to "fsl,gianfar-mdio"
* Removed device_type = "mdio"
The matching for gianfar mdio still supports the old "mdio"/"gianfar" combo
but it is now considered deprecated.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The addition of the aliases node is needed for U-Boot
and, eventually, cuImage, to help locate the proper
nodes reliably when using the libfdt approach.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that earlier patches have switched the bootwrapper to using libfdt
for device tree manipulation, this patch removes the now unused
flatdevtree.c and related files.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This incorporates libfdt (from the source embedded in an earlier
commit) into the wrapper.a library used by the bootwrapper. This
includes adding a libfdt_env.h file, which the libfdt sources need in
order to integrate into the bootwrapper environment, and a
libfdt-wrapper.c which provides glue to connect the bootwrapper's
abstract device tree callbacks to the libfdt functions.
In addition, this changes the various wrapper and platform files to
use libfdt functions instead of the older flatdevtree.c library.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This incorporates a copy of dtc libfdt into the kernel source, in
arch/powerpc/boot/libfdt. This only imports the upstream sources
verbatim, later patches are needed to actually link it into the kernel
Makefiles.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are a few variants of the STACR register that affect more than
just the "AXON" version of EMAC. Replace the current test of various
chip models with tests for generic properties in the device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
More than just "AXON" version of EMAC RGMII supports MDIO, so replace
the current test with a generic property in the device-tree that
indicates such support.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This adds a 'bootwrapper_install' make target for the powerpc
architecture, which installs the wrapper script, intermediate object
files and device-tree sources for later use.
This will then allow bootable zImages to be created other than in the
context of a kernel build.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It's possible that the executables which are built as helpers for the
bootwrapper stuff might end up in a different place to the intermediate
object files. Handle that.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If a .dts file is given to the bootwrapper script without a full path
name, look in a sensible place for it.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The bootwrapper script currently generates an 'otheros.bld' file in
addition to the file specified by the -o option, when asked to build a
wrapper for PS3.
It should do that in the same directory as the output, not the directory
where the wrapper objects are kept (which might potentially not be
writable when the script runs).
Arguably, the 'otheros.bld' ought to be created with the filename
specified as the -o argument. But that's a more intrusive change.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now the rtc class ds1374 driver has been added, remove the old rtc
driver hookup code, add rtc node to device trees, and turn on the
new driver in the defconfigs.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The interrupt map for the PCI PHB that had the ULI1575 was not correct
on the boards that have it.
* 8544 DS:
- Fix interrupt mask
- Be explicit about use of INTA for on chip peripherals
* 8572 DS/8641 HPCN:
- Fix interrupt mask
- Expand interrupt map for PCI slots to cover all functions
- Be explicit about use of INTA for on chip peripherals
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
correct the reg property, remove duplicate io port entry, whitespace fixes.
Thanks to Peter Van Ackeren for pointing this out.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The ps3 target produces two images, and the binary one is not the
"primary" image that corresponds to the -o flag; thus, it no longer
uses the generic binary flag.
On platforms which do use the binary flag, it no longer produces a
.bin suffix, so that the output file matches what was passed to the -o flag.
This should fix the zImage ln problems for the ps3 target.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Re-order the EMAC interrupts in the walnut.dts file so that they are mapped
correctly.
Signed-off-by: Steve Falco <sfalco at harris.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add the 'set -e' command to the wrapper script so that if any command
fails then the script will automatically exit
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Allow wrapper script to print verbose progress when the V is set in the
environment.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add 'fsl,' prefix to 'compatible' property for gpt nodes.
Add 'fsl,' prefix to empty, GPT0 specific 'has-wdt' property.
The fsl, prefix is being added to better match the convention of prefixing
manufacturer specific properties and values with the vendors name.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix some device tree omissions that prevented the new EMAC driver from
setting up ethernet on the Bamboo board correctly and update the Bamboo
defconfig.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch enables the ibm_newemac driver for the Walnut board. It fixes the
device tree for the walnut board to order the MAL interrupts correctly and
adds the local-mac-address property to the EMAC node. The bootwrapper is also
updated to extract the MAC address from the OpenBIOS offset where it is stored.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The current bootwrapper fails to set the timebase clock to the CPU clock
which causes the time to increment incorrectly. This fixes it by using the
correct #define for the CPC0_CR1 register.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds RGMII support to Sequoia DTS and sets correct phy-mode
for EMACs. According to Sequoia datasheet, both ethernet ports
are connected to RGMII interface, while ZMII is used only for MDIO.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add device tree entries for lite5200b's FEC's PHY.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds a memchr() implementation to the bootwrapper, which will
be needed when libfdt is merged in.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We don't use any CPM devices on these boards, but the muram node on these
chips is different from the 8560, so it's helpful to people working with
custom boards based on these chips.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add '-g' to BOOTCFLAGS if CONFIG_DEBUG_INFO is set.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
DTC now supports "foo","bar" format for lists of strings; use the new
format on the lite5200 device trees.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
1. UCC1's RX_DV pin is 16, not 15;
2. UCC1's phy is at 0x7, not 0x1. Schematics says 0x7, and recent
u-boot also using 0x7.
3. Use gianfar's (eTSEC) mdio bus. This is hardware default setup.
4. tx-clock should be CLK16 (GE125, PB31);
5. phy-connection-type is RGMII-ID;
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the majority of 85xx & 86xx we have a register that's ability to
assert HRESET_REQ to reset the board. We refactored that code so it
can be shared between both platforms into fsl_soc.c and removed all
the duplication in each platform directory.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
According to booting-without-of.txt, compatible should be "fsl_spi" and
mode "cpu" or "qe" for the fsl SPI controllers.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCI nodes on the MPC8568 dts didn't get moved up to be sibilings of the
SOC node when we did that clean up for some reason. Fix that up and some
minor whitespace and adjusting the size of the soc reg property.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8568E-MDS have DS1374 chip on the I2C bus, thus let's use it.
This patch also adds #address-cells and #size-cells to the I2C
controllers nodes.
p.s. DS1374 rtc class driver is in the -mm tree, its name is
rtc-rtc-class-driver-for-the-ds1374.patch.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The way the current CPM binding describes available multi-user (a.k.a.
dual-ported) RAM doesn't work well when there are multiple free regions,
and it doesn't work at all if the region doesn't begin at the start of
the muram area (as the hardware needs to be programmed with offsets into
this area). The latter situation can happen with SMC UARTs on CPM2, as its
parameter RAM is relocatable, u-boot puts it at zero, and the kernel doesn't
support moving it.
It is now described with a muram node, similar to QE. The current CPM
binding is sufficiently recent (i.e. never appeared in an official release)
that compatibility with existing device trees is not an issue.
The code supporting the new binding is shared between cpm1 and cpm2, rather
than remain separated. QE should be able to use this code as well, once
minor fixes are made to its device trees.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds cuboot support for MPC7448HPC2 platform.
The cuImage can be used with legacy u-boot without FDT support.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
1. PCI and reset are factored out into pq2.c. I renamed them from m82xx
to pq2 because they won't work on the Integrated Host Processor line of
82xx chips (i.e. 8240, 8245, and such).
2. The PCI PIC, which is nominally board-specific, is used on multiple
boards, and thus is used into pq2ads-pci-pic.c.
3. The new CPM binding is used.
4. General cleanup.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This board is also resold by Freescale under the names
"QUICCStart MPC885 Evaluation System" and "CWH-PPC-885XN-VE".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It now uses the new CPM binding and the generic pin/clock functions, and
has assorted fixes and cleanup.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The localbus node is used to describe devices that are connected via a chip
select or similar mechanism. The advantages over placing the devices under
the root node are that it can be probed without probing other random things
under the root, and that the description of which chip select a given device
uses can be used to set up mappings if the firmware failed to do so in a
useful manner.
cuboot-pq2 is updated to match the binding; previously, it called itself
chipselect rather than localbus, and used phandle linkage between the
actual bus node and the control node (the current agreement is to simply use
the fully-qualified address of the control registers, and ignore the overlap
with the IMMR node).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fsl_get_immr() uses /soc/ranges to determine the immr.
mpc885_get_clock() transforms a crystal frequency into a system frequency
according to the PLL register settings.
pq2_get_clocks() does the same as the above for the PowerQUICC II,
except that it produces several different clocks.
The mpc8xx/pq2 set_clocks() functions modify common properties in
the device tree based on the given clock data.
The mpc885/pq2 fixup_clocks() functions call get_clocks(), and
pass the results to set_clocks().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Wolfgang Grandegger
Anton Vorontsov
Kumar Gala
Remi Machet
Paul Mackerras
Adrian Bunk
Bryan O'Donoghue
Jason Jin
Timur Tabi
Sean MacLennan
Josh Boyer
David Gibson
Jeremy McNicoll
Zhang Wei
Christian Ehrhardt
Grant Likely
s.hauer@pengutronix.de
York Sun
Stefan Roese
John Linn
Haiying Wang
Paul Gortmaker
Scott Wood
Laurent Pinchart
Sebastian Siewior
Dale Farnsworth
Mark A. Greer
René Bürgel
Bartlomiej Sieka
Harvey Harrison
Geoff Levand
Kim Phillips
Alexandr Smirnov
Li Yang
Valentine Barshak
John Rigby
Jon Loeliger
Jon Loeliger
Roel Kluin
David Gibson
Wade Farnsworth
Vitaly Bordug
Johann Felix Soden
Marian Balakowicz
Jochen Friedrich
Stephen Neuendorffer
Matthias Fuchs
Benjamin Herrenschmidt
Hugh Blemings
joe@perches.com
David Woodhouse
Steven A. Falco
Domen Puncer
Xianghua Xiao
Peter Korsgaard
Roy Zang