The xics code currently has a direct and lpar variant of
xics_host_map, the only difference being which irq_chip they use. If
we remember which irq_chip we're using we can combine these two
routines. That also allows us to have a single irq_host_ops instead
of two.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
pseries_mpic_init_IRQ() implements the same logic as the xics code did to
find the i8259 cascade irq. Now that we've pulled that logic out into
pseries_setup_i8259_cascade() we can use it in the mpic code.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the xics references from xics_setup_8259_cascade(), and merge the
good bits from the almost identical logic in pseries_mpic_init_IRQ().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code in xics.c to setup the i8259 cascaded irq handler is not really
xics specific, so move it into setup.c - we will clean this up further in
a subsequent patch.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is logic in platforms/peries/lpars.c which checks if the user has
specified a console on the command line, and refrains from adding a
preferred console entry for the hvc/hvsi console if they have.
This trips up if you use "netconsole=foo" on the command line, and has
the result that you get _only_ the netconsole, because the hvc device is
never added as a preferred console. Worse still if you get the netconsole
configuration wrong somehow, you end up with no console at all.
As it turns out we don't need to worry about checking the command line.
If the user has specified "console=foo", then foo will be set as the
preferred console when the command line is parsed in start_kernel(), much
later than the pseries code, and so the latter setting will take effect.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move the prototype for find_udbg_vterm() into pseries.h, removing
it from setup.c.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes the way we calculate how much space to reserve for the
pHyp dump. Currently we reserve 256MB only. With this change, the
code first checks to see if an amount has been specified on the boot
command line with the "phyp_dump_reserve_size" option, and if so, uses
that much.
Otherwise it computes 5% of total ram and rounds it down to a multiple
of 256MB, and uses the larger of that or 256MB.
This is for large systems with a lot of memory (10GB or more). The
aim is to have more space available for the kernel on reboot on
machines with more resources. Although the dump will be collected
pretty fast and the memory released really early on allowing the
machine to have the full memory available, this alleviates any issues
that can be caused by having way too little memory on very very large
systems during those few minutes.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A couple of places are duplicating the function of
of_device_is_available; convert them to use it.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
scanlog_init() could use some love.
* properly return -ENODEV if this system doesn't support scan-log-dump
* don't printk if scan-log-dump not present; only older systems have it
* convert from create_proc_entry() to preferred proc_create()
* allocate zeroed data buffer
* fix potential memory leak of ent->data on failed create_proc_entry()
* simplify control flow
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds /sys/kernel/phyp_dump_active so that kdump init scripts may
look for it and take appropriate action if this file is found. This
file is only created when phyp_dump has been registered.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a kernel command line option "phyp_dump", which takes a 0/1
value for disabling/ enabling phyp_dump at boot time. Kdump can use
this on cmdline (phyp_dump=0) to disable phyp-dump during boot when
enabling itself. This will ensure only one dumping mechanism is active
at any given time.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This tracks the size freed. For now it does a simple rudimentary
calculation of the ranges freed. The idea is to keep it simple at the
external shell script level and send in large chunks for now.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds routines to
a. invalidate dump
b. calculate region that is reserved and needs to be freed. This is
exported through sysfs interface.
Unregister has been removed for now as it wasn't being used.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Set up the actual dump header, register it with the hypervisor.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Check to see if there actually is data from a previously
crashed kernel waiting. If so, allow user-space tools to
grab the data (by reading /proc/kcore). When user-space
finishes dumping a section, it must release that memory
by writing to sysfs. For example,
echo "0x40000000 0x10000000" > /sys/kernel/release_region
will release 256MB starting at the 1GB. The released memory
becomes free for general use.
Signed-off-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Initial patch for reserving memory in early boot, and freeing it
later. If the previous boot had ended with a crash, the reserved
memory would contain a copy of the crashed kernel data.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The hypervisor can look at the value in the wait_state_cycles field of
the VPA for an estimate of how busy dedicated processors are.
Currently, as the kernel never touches this field, we appear to be
100% busy. This records the duration the kernel is in powersave and
passes that to the HV to provide a reasonable indication of
utilisation.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For memory remove, we need to clean up htab mappings for the
section of the memory we are removing.
This implements support for removing htab bolted mappings for pSeries
logical partitions. Other sub-archs may need to implement similar
functionality for hotplug memory remove to work on them.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Introduced by commit 79393fc46e
("kobject: convert pseries/power.c to kobj_attr interface").
sys_create_file takes a "struct attrbute *" not a "struct
kobj_addribute *".
arch/powerpc/platforms/pseries/power.c: In function 'apo_pm_init':
arch/powerpc/platforms/pseries/power.c:78: warning: passing argument 2 of 'sysfs_create_file' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The xics code does update the default server information when the boot
cpu is removed. This patch recognizes when the boot cpu is being
removed and updates the appropriate information based on the new 'boot
cpu'.
Failure to update this information can causes us to leave irqs pinned
to cpus that are being removed, especially when removing the boot cpu.
The cpu is removed from the kernel, but cpu dlpar remove operations
fail since we cannot return the cpu to the hypervisor.
Signed-off-by: Nathan Fonteno <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It appears that xics.c has its own of_get_cpu_node(). Remove this and
use the common one from prom.c.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This splits off the kexec path bits of the xics_teardown_cpu() routine
into its own xics_kexec_teardown_cpu() routine. With the previous
combined routine the CPPR for a cpu that is being removed may have its
CPPR reset in the plpar_eoi() call (which explicitly sets the CPPR to
a non-zero value). Splitting of the kexec bits of the code prevents
this from happening in the cpu remove path.
Once again, this does not cause the cpu remove from the kernel to
fail, but it does cause cpu dlpar operations to not be able to return
the cpu to the hypervisor.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The affinity mask in the virq descriptor needs to be set before we
reset the affinity for the virq. Without doing this the call to get
the new irq server fails and we end up leaving the virq pinned to the
cpu we are removing.
This does not fail the cpu remove from the kernel, but it does prevent
cpu dlpar remove operations from returning the cpu to the hypervisor.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Of_get_parent and of_find_compatible_node do an of_node_get, and thus a
corresponding of_code_put is needed in the error case.
The problem was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T,T1,T2;
identifier E;
statement S;
expression x1,x2,x3;
int ret;
@@
T E;
...
* E = \(of_get_parent\|of_find_compatible_node\)(...);
if (E == NULL) S
... when != of_node_put(...,(T1)E,...)
when != if (E != NULL) { ... of_node_put(...,(T1)E,...); ...}
when != x1 = (T1)E
when != E = x3;
when any
if (...) {
... when != of_node_put(...,(T2)E,...)
when != if (E != NULL) { ... of_node_put(...,(T2)E,...); ...}
when != x2 = (T2)E
(
* return;
|
* return ret;
)
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace all lock_cpu_hotplug/unlock_cpu_hotplug from the kernel and use
get_online_cpus and put_online_cpus instead as it highlights the
refcount semantics in these operations.
The new API guarantees protection against the cpu-hotplug operation, but
it doesn't guarantee serialized access to any of the local data
structures. Hence the changes needs to be reviewed.
In case of pseries_add_processor/pseries_remove_processor, use
cpu_maps_update_begin()/cpu_maps_update_done() as we're modifying the
cpu_present_map there.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
/sys/power should not be a kset, that's overkill. This patch renames it
to power_kset and fixes up all usages of it in the tree.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes the code a bit simpler and and gets us one step closer to
deleting the deprecated subsys_attr code.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dynamically create the kset instead of declaring it statically. We also
rename power_subsys to power_kset to catch all users of the variable and
we properly export it so that people don't have to guess that it really
is present in the system.
The pseries code is wierd, why is it createing /sys/power if CONFIG_PM
is disabled? Oh well, stupid big boxes ignoring config options...
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need a "default" ktype for a kset. We should set this
explicitly every time for each kset. This change is needed so that we
can make ksets dynamic, and cleans up one of the odd, undocumented
assumption that the kset/kobject/ktype model has.
This patch is based on a lot of help from Kay Sievers.
Nasty bug in the block code was found by Dave Young
<hidave.darkstar@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 473980a993 added a call to clear
the SLB shadow buffer before registering it. Unfortunately this means
that we clear out the entries that slb_initialize has previously set in
there. On POWER6, the hypervisor uses the SLB shadow buffer when doing
partition switches, and that means that after the next partition switch,
each non-boot CPU has no SLB entries to map the kernel text and data,
which causes it to crash.
This fixes it by reverting most of 473980a9 and instead clearing the
3rd entry explicitly in slb_initialize. This fixes the problem that
473980a9 was trying to solve, but without breaking POWER6.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Before we register the SLB shadow buffer, we need to invalidate the
entries in the buffer, otherwise we can end up stale entries from when
we previously offlined the CPU.
This does this invalidate as well as unregistering the buffer with
PHYP before we offline the cpu. Tested and fixes crashes seen on
970MP (thanks to tonyb) and POWER5.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PCI code in 32 and 64 bits fixes up resources differently.
32 bits uses a header quirk plus handles bridges in pcibios_fixup_bus()
while 64 bits does things in various places depending on whether you
are using OF probing, using PCI hotplug, etc...
This merges those by basically using the 32 bits approach for both,
with various tweaks to make 64 bits work with the new approach.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The per-processor interrupt request register and current processor
priority register are only accessed on the current cpu. In fact the
hypervisor doesn't even let us choose which cpu's registers to access.
The only function to use cpu twice is xics_migrate_irqs_away, not a fast
path. But we can cache the result of get_hard_processor_id() instead of
calling get_hard_smp_processor_id(cpu) in a loop across the call to rtas.
Years ago the irq code passed smp_processor_id into get_irq, I thought
we might initialize the CPPR third party at boot as an extra measure of
saftey, and it made the code symmetric with the qirr (queued interrupt
for software generated interrupts), but now it is just extra and
sometimes unneeded work to pass it down.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It only needs the iommu_table address. It also makes use of the node
name to print error messages. So just pass it the things it needs.
This reduces the places that know about the pci_dn by one.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Do not wait for the pci slot status before reporting an error
to the device driver. Some systems may take many seconds to
report the slot status, and this can confuse unsuspecting
device drivers.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If an "empty" slot is failing, make sure its a permanent failure;
else process the error normally.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Perform all error checking at the "partitonable endpoint"
of the device.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
prod_processor() is unused, and that's a good thing, since it does not
supply the required proc id parameter to H_PROD.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This cleans up the SMT thread handling, removing some hard coded
assumptions and providing a set of helpers to convert between linux
cpu numbers, thread numbers and cores.
This implementation requires the number of threads per core to be a
power of 2 and identical on all cores in the system, but it's an
implementation detail, not an API requirement and so this limitation
can be lifted in the future if anybody ever needs it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit a2b51812a4.
It turns out that this change caused some machines to fail to come
back up when being rebooted, and generated an error in the hypervisor
error log on some machines. The platform architecture (PAPR) is a
little unclear on exactly when the RTAS ibm,os-term function should be
called. Until that is clarified I'm reverting this commit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The rtas_os_term() routine was being called at the wrong time.
The actual rtas call "os-term" will not ever return, and so
calling it from the panic notifier is too early. Instead,
call it from the machine_reset() call.
This splits the rtas_os_term() routine into two: one part to capture
the kernel panic message, invoked during the panic notifier, and
another part that is invoked during machine_reset().
Prior to this patch, the os-term call was never being made,
because panic_timeout was always non-zero. Calling os-term
helps keep the hypervisor happy! We have to keep the hypervisor
happy to avoid service, dump and error reporting problems.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix old buglet; a warning message should have been printed
when a hardware reset takes too long.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Bugfix: avoid crash if there's no PCI device for a given
openfirmware node.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Bugfix: if a driver controlling one part of a multi-function PCI card
has asked for a reset, honor that request above all others.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the error
error: implicit declaration of function "udbg_printf"
We have a few spots where we reference udbg_printf() without #including
udbg.h. These are within #ifdef DEBUG blocks, so unnoticed until we do
a #define DEBUG or #define DEBUG_LOW nearby.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are plans afoot to use pci_restore_msi_state() to restore MSI
state after a device reset. In order for this to work for the RTAS MSI
backend, we need to read back the MSI message from config space after
it has been setup by firmware.
This should be sufficient for restoring the MSI state after a device
reset, however we will need to revisit this for suspend to disk if that
is ever implemented on pseries.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
is_init() is an ambiguous name for the pid==1 check. Split it into
is_global_init() and is_container_init().
A cgroup init has it's tsk->pid == 1.
A global init also has it's tsk->pid == 1 and it's active pid namespace
is the init_pid_ns. But rather than check the active pid namespace,
compare the task structure with 'init_pid_ns.child_reaper', which is
initialized during boot to the /sbin/init process and never changes.
Changelog:
2.6.22-rc4-mm2-pidns1:
- Use 'init_pid_ns.child_reaper' to determine if a given task is the
global init (/sbin/init) process. This would improve performance
and remove dependence on the task_pid().
2.6.21-mm2-pidns2:
- [Sukadev Bhattiprolu] Changed is_container_init() calls in {powerpc,
ppc,avr32}/traps.c for the _exception() call to is_global_init().
This way, we kill only the cgroup if the cgroup's init has a
bug rather than force a kernel panic.
[akpm@linux-foundation.org: fix comment]
[sukadev@us.ibm.com: Use is_global_init() in arch/m32r/mm/fault.c]
[bunk@stusta.de: kernel/pid.c: remove unused exports]
[sukadev@us.ibm.com: Fix capability.c to work with threaded init]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Acked-by: Pavel Emelianov <xemul@openvz.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Herbert Poetzel <herbert@13thfloor.at>
Cc: Kirill Korotaev <dev@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes the kernel use 1TB segments for all kernel mappings and for
user addresses of 1TB and above, on machines which support them
(currently POWER5+, POWER6 and PA6T).
We detect that the machine supports 1TB segments by looking at the
ibm,processor-segment-sizes property in the device tree.
We don't currently use 1TB segments for user addresses < 1T, since
that would effectively prevent 32-bit processes from using huge pages
unless we also had a way to revert to using 256MB segments. That
would be possible but would involve extra complications (such as
keeping track of which segment size was used when HPTEs were inserted)
and is not addressed here.
Parts of this patch were originally written by Ben Herrenschmidt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Don't allow cpu hotplug on systems lacking XICS interrupt controller
(i.e. with an MPIC interrupt controller), since the current pSeries
platform code is hardcoded for XICS.
This works around the bug reported by Paul Mackerras where the
disable_nonboot_cpus() call recently added to the shutdown path will
cause an oops on older pSeries machines.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is no good reason for board platform code to mess with the
ROOT_DEV. Remove it from all in-tree platforms except powermac.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some older pSeries machines were panicking in pSeries_log_error
because it was getting called before it was ready. This is a result
of commit "[POWERPC] pseries: Fix jumbled no_logging flag."
(79c0108d1b).
This fixes it by explicitly enabling RTAS error logging when it has
been initialized, and also makes the code clearer by renaming the
"no_more_logging" variable to "logging_enabled".
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently rtas_change_msi() returns either the error code from RTAS, or if
the RTAS call succeeded the number of irqs that were configured by RTAS.
This makes checking the return value more complicated than it needs to be.
Instead, have rtas_change_msi() check that the number of irqs configured by
RTAS is equal to what we requested - and return an error otherwise. This makes
the return semantics match the usual 0 for success, something else for error.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
rtas_setup_msi_irqs() doesn't need to call teardown() itself, the
generic code will do this for us as long as we return a non-zero
value.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It seems that some versions of firmware will report a device
node status as the string "okay". As we are not expecting this
string, the device node will be ignored by the EEH subsystem.
Which means EEH will not be enabled.
When EEH is not enabled, PCI errors will be converted into
Machine Check exceptions, and we'll have a very unhappy system.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On a POWER6 machine running 2.6.23-rc8 I sometimes see the following error:
xics_set_affinity: No online cpus in the mask 00000000,00000000,00000000,00000001 for irq 20
In a desperate attempt to get a changelog entry in 2.6.23, I took a look
into it.
It turns out we are passing a real and not a virtual irq into
get_irq_server. This works for the case where hwirq < NR_IRQS and we
set virq = hwirq. In my case however hwirq = 590082 and we try and
access irq_desc[590082], slightly past the end at 512 entries.
Lucky we ship lots of memory with our machines.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The majority of irq_host implementations (3 out of 4) are associated
with a device_node, and need to stash it somewhere. Rather than having
it somewhere different for each host, add an optional device_node pointer
to the irq_host structure.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove dead code, and a misleading comment about EEH checking
for video devices. The removed code is a left-over from the
olden days where there was concern over how video devices
worked in Linux. We are never going to go that way again,
so kill this.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
arch/powerpc/platforms/pseries/eeh.c | 17 -----------------
1 file changed, 17 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Eliminate the use of error_log_cnt as a global var shared across
different directories. Pass it as a parameter instead.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
Respin of earlier patch, with the CONFIG_PSERIES junk removed from the
header file.
arch/powerpc/kernel/nvram_64.c | 10 +++++-----
arch/powerpc/platforms/pseries/rtasd.c | 7 ++++---
include/asm-powerpc/nvram.h | 6 ++++--
3 files changed, 13 insertions(+), 10 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Get rid of the jumbled usage of the no_logging flag. Its use
spans several directories, and is incorrectly/misleadingly
documented. Instead, two changes:
1) nvram will accept error log as soon as its ready.
2) logging to nvram stops on the first fatal error reported.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
arch/powerpc/kernel/nvram_64.c | 8 --------
arch/powerpc/platforms/pseries/rtasd.c | 14 ++++++--------
2 files changed, 6 insertions(+), 16 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Simplify rtasd initialization code; this also fixes a buglet,
where the /proc entries weren't being cleaned up in case of
failure.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
arch/powerpc/platforms/pseries/rtasd.c | 53 +++++++++++----------------------
1 file changed, 19 insertions(+), 34 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
The rtas_token() call does the same thing as this hand-rolled code.
This makes the code easier to read.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
arch/powerpc/platforms/pseries/rtasd.c | 13 ++-----------
1 file changed, 2 insertions(+), 11 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
We don't need to look up the rtas event token once per
cpu per second. This avoids some misc device-tree lookups
and string ops and so provides some minor performance
improvement.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
Revised commit-log message.
arch/powerpc/platforms/pseries/rtasd.c | 15 +++++++++------
1 file changed, 9 insertions(+), 6 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes several duplicate includes from arch/powerpc/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The EEH code needs to ignore PCI bridges; sort-of. It was ignoring
them in the wrong place, and thus failing to set up the
PCI_DN(dn)->pcidev pointer. Imprudent dereferencing of this pointer
would lead to a crash on cards with bridges.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
arch/powerpc/platforms/pseries/eeh_cache.c | 9 +++++----
1 file changed, 5 insertions(+), 4 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move firmware feature initialisation from pSeries_init_early to the
earlier pSeries_probe_hypertas so they are initialised before firmware
feature fixups are applied.
Currently firmware feature sections are only used for iSeries which
initialises the these features much earlier. This is a bug in waiting
on pSeries.
Also adds some whitespace fixups.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (209 commits)
[POWERPC] Create add_rtc() function to enable the RTC CMOS driver
[POWERPC] Add H_ILLAN_ATTRIBUTES hcall number
[POWERPC] xilinxfb: Parameterize xilinxfb platform device registration
[POWERPC] Oprofile support for Power 5++
[POWERPC] Enable arbitary speed tty ioctls and split input/output speed
[POWERPC] Make drivers/char/hvc_console.c:khvcd() static
[POWERPC] Remove dead code for preventing pread() and pwrite() calls
[POWERPC] Remove unnecessary #undef printk from prom.c
[POWERPC] Fix typo in Ebony default DTS
[POWERPC] Check for NULL ppc_md.init_IRQ() before calling
[POWERPC] Remove extra return statement
[POWERPC] pasemi: Don't auto-select CONFIG_EMBEDDED
[POWERPC] pasemi: Rename platform
[POWERPC] arch/powerpc/kernel/sysfs.c: Move NUMA exports
[POWERPC] Add __read_mostly support for powerpc
[POWERPC] Modify sched_clock() to make CONFIG_PRINTK_TIME more sane
[POWERPC] Create a dummy zImage if no valid platform has been selected
[POWERPC] PS3: Bootwrapper support.
[POWERPC] powermac i2c: Use mutex
[POWERPC] Schedule removal of arch/ppc
...
Fixed up conflicts manually in:
Documentation/feature-removal-schedule.txt
arch/powerpc/kernel/pci_32.c
arch/powerpc/kernel/pci_64.c
include/asm-powerpc/pci.h
and asked the powerpc people to double-check the result..
The struct device_node currently has a _flags variable, although
it's only used for one flag - OF_DYNAMIC. Generalise the flag
accessors so we can use them with other flags in future.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On Power machines supporting VRMA, Kexec/Kdump does not work.
VRMA (virtual real-mode area) means that accesses with IR/DR = 0
(i.e. the MMU "off") actually still go through the hash table,
using entries put there by the hypervisor.
This means that when we clear out the hash table on kexec, we need to
make sure these entries are left untouched.
This also adds plpar_pte_read_raw() on the lines of
plpar_pte_remove_raw().
Signed-off-by : Sachin Sant <sachinp@in.ibm.com>
Signed-off-by : Mohan Kumar M <mohan@in.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In some of the PPC970 based systems, interrupt would be distributed to
offline cpus also even when booted with "maxcpus=1". So check whether
cpu online map and cpu present map are equal or not. If they are equal
default_distrib_server is used as interrupt server otherwise boot cpu
(default_server) used as interrupt server.
In addition to this, if an interrupt is assigned to a specific cpu (ie
smp affinity) and if that cpu is not online, the earlier code used to
return the default_distrib_server as interrupt server. This
introduces an additional parameter to the get_irq function, called
strict_check. Based on this parameter, if the cpu is not online
either default_distrib_server or -1 is returned.
Signed-off-by: Mohan Kumar M <mohan@in.ibm.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A Power6 can give up CPU cycles on a dedicated CPU (as opposed to a
shared CPU) to other shared processors if the administrator asks for it
(via the HMC).
This enables that to work properly on P6.
This just involves setting a bit in the CAS structure as well as the
VPA. To donate cycles, a CPU has to have all SMT threads idle and
have the donate bit set in the VPA. Then call H_CEDE.
The reason why shared processors just aren't used is because dedicated
CPUs are guaranteed an actual processor, yet the system is still able to
increase the capacity of the shared CPU pool.
Also rename the VPA's cpuctls_task_attrs field to a more accurate name.
Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This rewrites pretty much from scratch the handling of MMIO and PIO
space allocations on powerpc64. The main goals are:
- Get rid of imalloc and use more common code where possible
- Simplify the current mess so that PIO space is allocated and
mapped in a single place for PCI bridges
- Handle allocation constraints of PIO for all bridges including
hot plugged ones within the 2GB space reserved for IO ports,
so that devices on hotplugged busses will now work with drivers
that assume IO ports fit in an int.
- Cleanup and separate tracking of the ISA space in the reserved
low 64K of IO space. No ISA -> Nothing mapped there.
I booted a cell blade with IDE on PIO and MMIO and a dual G5 so
far, that's it :-)
With this patch, all allocations are done using the code in
mm/vmalloc.c, though we use the low level __get_vm_area with
explicit start/stop constraints in order to manage separate
areas for vmalloc/vmap, ioremap, and PCI IOs.
This greatly simplifies a lot of things, as you can see in the
diffstat of that patch :-)
A new pair of functions pcibios_map/unmap_io_space() now replace
all of the previous code that used to manipulate PCI IOs space.
The allocation is done at mapping time, which is now called from
scan_phb's, just before the devices are probed (instead of after,
which is by itself a bug fix). The only other caller is the PCI
hotplug code for hot adding PCI-PCI bridges (slots).
imalloc is gone, as is the "sub-allocation" thing, but I do beleive
that hotplug should still work in the sense that the space allocation
is always done by the PHB, but if you unmap a child bus of this PHB
(which seems to be possible), then the code should properly tear
down all the HPTE mappings for that area of the PHB allocated IO space.
I now always reserve the first 64K of IO space for the bridge with
the ISA bus on it. I have moved the code for tracking ISA in a separate
file which should also make it smarter if we ever are capable of
hot unplugging or re-plugging an ISA bridge.
This should have a side effect on platforms like powermac where VGA IOs
will no longer work. This is done on purpose though as they would have
worked semi-randomly before. The idea at this point is to isolate drivers
that might need to access those and fix them by providing a proper
function to obtain an offset to the legacy IOs of a given bus.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Twiddle the copyright notices. Per current guidelines, the use
of the (C) or (c) in source code is deprecated.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
arch/powerpc/platforms/pseries/eeh.c | 6 +++++-
arch/powerpc/platforms/pseries/eeh_cache.c | 3 ++-
arch/powerpc/platforms/pseries/eeh_driver.c | 6 +++---
3 files changed, 10 insertions(+), 5 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Track and report the number of times we read an all-1s value (0xff,
0xffff or 0xffffffff) from each device which is valid data, not
indicating EEH isolation.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
arch/powerpc/platforms/pseries/eeh.c | 5 +++++
arch/powerpc/platforms/pseries/eeh_sysfs.c | 3 +++
include/asm-powerpc/pci-bridge.h | 1 +
3 files changed, 9 insertions(+)
Signed-off-by: Paul Mackerras <paulus@samba.org>
In 616883df78 request_irq was marked as
__must_check so we must... er... check it.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/platforms/pseries/pseries.h:24: warning: return type defaults to 'int'
arch/powerpc/platforms/pseries/pseries.h:25: warning: return type defaults to 'int'
arch/powerpc/platforms/pseries/pseries.h:24: warning: control reaches end of non-void function
arch/powerpc/platforms/pseries/pseries.h:25: warning: control reaches end of non-void function
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 2f4dfe206a moved the definition
of hard_smp_processor_id() for the UP case from include/linux/smp.h
to include/asm/smp.h. However, include/linux/smp.h only includes
include/asm/smp.h in the SMP case, so code that wants to use
hard_smp_processor_id() has to include <asm/smp.h> explicitly to
be sure of getting the definition.
Signed-off-by: Paul Mackerras <paulus@samba.org>
pci is not initialized before being used here, so this debug print is
bogus at the current location. Move it to where it makes sense.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When an EEH event is detected, and after the device driver
has been notified, but before the device is reset, enable
MMIO to the adapter, and grab the contents of the PCI status
and command registers, the PCI-X status and command, and the
PCI-E capability 10 and AER registers. Pass these up to the
RTAS error log, and also printk them.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If an EEH event is observed, capture PCI config space info about
the device, wrap it up and pass it to the event logger. This
pach just slots in the basic logging function. A later patch
will provide for more through data gathering.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make some minor adjustments to the EEH error messages.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It turns out many/most versions of firmware enable MMIO when
the slto-error-detail rtas call is made (in violation of the
architecture). Thus, it would be best to call slot-error-detail
only after notifying device drivers of a freeze, as otherwise,
a variety of strange and unexpected things may happen.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implement MSI support via RTAS (RTAS = run-time firmware on pSeries
machines). For now we assumes that if the required RTAS tokens for
MSI are present, then we want to use the RTAS MSI routines.
When RTAS is managing MSIs for us, it will/may enable MSI on devices that
support it by default. This is contrary to the Linux model where a device
is in LSI mode until the driver requests MSIs.
To remedy this we add a pci_irq_fixup call, which disables MSI if they've
been assigned by firmware and the device also supports LSI. Devices that
don't support LSI at all will be left as is, drivers are still expected
to call pci_enable_msi() before using the device.
At the moment there is no pci_irq_fixup on pSeries, so we can just set it
unconditionally. If other platforms use the RTAS MSI backend they'll need
to check that still holds.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds the pSeries platform implementation for a new PCI API
which can be used to issue various types of PCI-E reset,
including PCI-E warm reset and PCI-E hot reset. This is needed
for an ipr PCI-E adapter which does not properly implement BIST.
Running BIST on this adapter results in PCI-E errors. The only
reliable reset mechanism that exists on this hardware is PCI
Fundamental reset (warm reset).
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The pseries PCI hotplug code cannot build as a module, unless
the pcibios_remove_pci_devices function is exported.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
arch/powerpc/platforms/pseries/pci_dlpar.c | 1 +
1 file changed, 1 insertion(+)
Signed-off-by: Paul Mackerras <paulus@samba.org>
for consistency with other Open Firmware interfaces (and Sparc).
This is just a straight replacement.
This leaves the compatibility define in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6:
remove "struct subsystem" as it is no longer needed
sysfs: printk format warning
DOC: Fix wrong identifier name in Documentation/driver-model/devres.txt
platform: reorder platform_device_del
Driver core: fix show_uevent from taking up way too much stack
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to work on cleaning up the relationship between kobjects, ksets and
ktypes. The removal of 'struct subsystem' is the first step of this,
especially as it is not really needed at all.
Thanks to Kay for fixing the bugs in this patch.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some versions of pSeries firmware fail to set up a
dma-window property for PCI slots that are unoccupied.
As a result, the loop searching for this propery, in
pci_dma_dev_setup_pSeriesLP(), can run to the end, resulting
in a NULL pointer dereference later in the routine. This
patch prevents the crash, and prints a warning message.
This is theoretically a rare error, as it occurs on what
is hopefully just beta levels of firmware. But just in case
this firmware escapes into the wild, this patch will avoid
the crash.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
check_legacy_ioport makes only sense on PREP, CHRP and pSeries.
They may have an isa node with PS/2, parport, floppy and serial ports.
Remove the check_legacy_ioport call from ppc_md, it's not needed
anymore. Hardware capabilities come from the device-tree.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix link errors with CONFIG_EEH=n:
arch/powerpc/platforms/built-in.o: In function `.pcibios_fixup_new_pci_devices':
(.text+0x41c8): undefined reference to `.eeh_add_device_tree_late'
arch/powerpc/platforms/built-in.o: In function `.init_phb_dynamic':
(.text+0x4280): undefined reference to `.eeh_add_device_tree_early'
arch/powerpc/platforms/built-in.o: In function `.pcibios_remove_pci_devices':
(.text+0x42fc): undefined reference to `.eeh_remove_bus_device'
arch/powerpc/platforms/built-in.o: In function `.pcibios_add_pci_devices':
(.text+0x43c0): undefined reference to `.eeh_add_device_tree_early'
arch/powerpc/platforms/built-in.o: In function `.pSeries_final_fixup':
(.init.text+0xb4): undefined reference to `.pci_addr_cache_build'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Moved pseries, iseries, chrp, prep, maple and pasemi into their respective
arch/powerpc/platform/*/Kconfig files out of arch/powerpc/Kconfig
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rework how multi-function PCI devices are identified and traversed.
This fixes a bug with multi-function recovery on Power4 that was
introduced by a recent Power4 EEH patch.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
After requesting a state change, verify that the state change
actually ocurred, and the system ends up in the expected state.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The EEH event notification system passes around data that is
not needed or at least, not used properly. Stop passing this
data; get it in a more reliable fashion.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Modify routine that returns PCI slot status to wait for slot status
to become available. This is needed, as slots that are in some remote
card cage may go offline for extended periods of time. New users for
this routine in following patches.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some firmware versions will return a slot reset state of "1"
when a slot is EEH frozen. Recognize this as a state that can be
handled.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the second or higher function of a multi-function device fails
to recover, this failure is not reported upwards. Fix this.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If a device driver does not have native PCI error recovery,
a hotplug error recovery will be attemped. In this case,
the device driver will not report back whether its healthy
or not; simply assume that it is.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Provide support for the new ibm,get-config-addr-info2 RTAS token,
whenever it is actually available.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some drivers will attempt to perform a lot of mmio even after
an EEH event was detected. This is especially the case for fast cpu's
and PCI-E slots. Be a bit more lenient in allowing this.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are multiple code patchs tht resuls in a "permanent
failure"; when examining rare events, it can be hard to see
which was taken. This patch adds printk's to assist.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the order in which pci error state is examined;
the "capabilites" is not valid if "reset state" is 5.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I noticed that we execute hcalls before cpu feature code has run (eg
for setting up the bolted kernel region). This means that we may be
executing code that is not appropriate for the processor we have.
Create an unconditional branch that we nop out all the time to fix this.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
kexec invokes plpar_hcall hypervisor call in real mode. plpar_hcall
refers to per cpu variables for accounting hypervisor statistics.
These variables may not be in the RMO region, so accesses to them
in real mode may result in a data storage exception.
This fixes this problem by using a new plpar_hcall_raw function which
does not update the hypervisor call statistics. Thanks to Anton for
suggesting this idea.
Signed-off-by: Mohan Kumar M <mohan@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This will allow us to build without PCI easier.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
During power outages, the UPS notifies the system for a shutdown.
In the current setup, it isn't possible to poweron when power is
restored. This patch fixes the issue by calling the right
ibm,power-off-ups token during such events. It also adds a sysfs
interface so userspace can specify whether or not to power on when
power is restored.
Signed-off-by: Manish Ahuja <ahuja@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My "cleanup" patch (dce623e082) had a cut
and paste error for the !CONFIG_KEXEC case. Fifty lashes for me.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move all the pseries kexec code into one file, platforms/pseries/kexec.c
Provide helpers for setting up ppc_md.kexec_cpu_down, so that we don't
have to have #ifdef CONFIG_KEXEC in setup.c
Move the initialisation of the ppc_md kexec callbacks into an init routine.
This is well and truly early enough to cause no change in behaviour, we
can't kexec until userspace has given us a kernel to kexec into.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move some extern declarations from setup.c into the new pseries.h.
While we're at it, provide dummy implementations for !SMP, to avoid
cluttering the C file with more #ifdefs.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Following the example of platforms/pasemi, consolidate a couple of
tiny header files in platforms/pseries into pseries.h.
This gives us a convenient place to put things that need to be
available to the platform code, but not public. And hopefully will
help people resist the temptation of sticking externs in C files.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
[akpm@osdl.org: sparc64 fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bug: pnx8550 code creates directory but resets ->nlink to 1.
create_proc_entry() et al will correctly set ->nlink for you.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous patch changing pSeries to use H_BULK_REMOVE broke the
JS20 blade, where the firmware doesn't support H_BULK_REMOVE. This
adds a firmware check so that on machines that don't have H_BULK_REMOVE,
we just use the H_REMOVE call as before.
Signed-off-by: Paul Mackerras <paulus@samba.org>
H_BULK_REMOVE lets us remove 4 entries from the MMU hash table with one
hypervisor call. This uses it in pSeries_lpar_hpte_invalidate so we
can tear down mappings with fewer hypervisor calls.
Signed-off-by: Paul Mackerras <paulus@samba.org>
It appears that EEH is improperly enabled for some Power4 systems.
On these systems, the ibm,set-eeh-option returns a value of success
even when EEH is not supported on the given node. Thus, an explicit
check for support is required.
During boot, on power4, without this patch, one sees messages
similar to:
EEH: event on unsupported device, rc=0 dn=/pci@400000000110/IBM,sp@1
EEH: event on unsupported device, rc=0 dn=/pci@400000000110/pci@2
EEH: event on unsupported device, rc=0 dn=/pci@400000000110/pci@2,2
etc.
The patch makes these go away.
Without this patch, EEH recovery does seem to work correctly for
at least some devices (I tested ethernet e1000), but fails to
recover others (the Emulex LightPulse LPFC, most notably).
Off the top of my head, I don't remember why some devices are
affected, but not others.
The PAPR indicates that the correct way to test for EEH is as
done in this patch; its not clear to me if this was in the PAPR
all along, or recently added; if it was there all along, its not
clear to me why this hadn't been fixed long ago. I suspect only
certain firmware levels are affected.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Note all POWER3/POWER4 systems where fixup_winbond_82c105 will run.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It appears that the iommu table address is never stored, and thus
never found, on non-lpar systems. Thus, for example, during boot:
<7>[ 93.067916] PCI: Scanning bus 0001:41
<7>[ 93.068542] PCI: Found 0001:41:01.0 [8086/100f] 000200 00
<7>[ 93.068550] PCI: Calling quirk c0000000007822e0 for 0001:41:01.0
<7>[ 93.069815] PCI: Fixups for bus 0001:41
<4>[ 93.070167] iommu: Device 0001:41:01.0 has no iommu table
<7>[ 93.070251] PCI: Bus scan for 0001:41 returning with max=41
No iommu table? How can that be? Well, circa line 471 of
arch/powerpc/platforms/pseries/iommu.c we see the code:
while (dn && PCI_DN(dn) && PCI_DN(dn)->iommu_table == NULL)
dn = dn->parent;
and a few lines later is the surprising print statement about
the missing table. Seems that this loop ran unto the end, never
once finding a non-null PCI_DN(dn)->iommu_table.
The problem can be found a few lines earlier: it sems that the
value of PCI_DN(dn)->iommu_table is never ever set. Thus, the
patch sets it.
The patch was tested on a Power4 system running in full system
partition mode, which is where I saw the problem. It works; I've
not done any wider testing. Had a brief discussion on this on irc.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There were a few issues with the HCALL_STATS code:
- PURR cpu feature checks were backwards
- We iterated one entry off the end of the hcall_stats array
- Remove dead update_hcall_stats() function prototype
I noticed one thing while debugging, and that is we call H_ENTER (to set
up the MMU hashtable in early init) before we have done the cpu fixups.
This means we will execute the PURR SPR reads even on a CPU that isnt
capable of it. I wonder if we can move the CPU feature fixups earlier.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It looks to me like we are corrupting r12 in the hcall9 function.
Although we have r0 free we cant use offsets against it, so save
away r12 in there instead. r12 holds the ninth return value from
the hypervisor call, so without this fix, the caller will see the
wrong value for the ninth element in the array that gets the return
values.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We can use default_server when masking an interrupt vector.
get_irq_server() assumes a virtual irq, so badness may happen if we
give it a real one.
Signed-off-by: Michal Ostrowski <mostrows@watson.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (36 commits)
[POWERPC] Generic BUG for powerpc
[PPC] Fix compile failure do to introduction of PHY_POLL
[POWERPC] Only export __mtdcr/__mfdcr if CONFIG_PPC_DCR is set
[POWERPC] Remove old dcr.S
[POWERPC] Fix SPU coredump code for max_fdset removal
[POWERPC] Fix irq routing on some 32-bit PowerMacs
[POWERPC] ps3: Add vuart support
[POWERPC] Support ibm,dynamic-reconfiguration-memory nodes
[POWERPC] dont allow pSeries_probe to succeed without initialising MMU
[POWERPC] micro optimise pSeries_probe
[POWERPC] Add SPURR SPR to sysfs
[POWERPC] Add DSCR SPR to sysfs
[POWERPC] Fix 440SPe CPU table entry
[POWERPC] Add support for FP emulation for the e300c2 core
[POWERPC] of_device_register: propagate device_create_file return code
[POWERPC] Fix mmap of PCI resource with hack for X
[POWERPC] iSeries: head_64.o needs to depend on lparmap.s
[POWERPC] cbe_thermal: Fix initialization of sysfs attribute_group
[POWERPC] Remove QE header files from lite5200.c
[POWERPC] of_platform_make_bus_id(): make `magic' int
...
pSeries_probe can decide that we are a pseries but then fail to
initialise the MMU. If an rtas node doesnt exist, we continually fall
out of pSeries_probe_hypertas early and never get to the MMU init code.
While pseries without RTAS is an illegal combination, the way we
currently fail is a pain to track down, and can happen if your flattened
device tree code has issues (like mine did :).
With the following patch we init the MMU, come up and print some
warnings about RTAS not existing, instead of looping on 0x400 exceptions.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman
Manish Ahuja
Paul Mackerras
Nathan Lynch
Harvey Harrison
Al Viro
Tony Breeds
Badari Pulavarty
Stephen Rothwell
Nathan Fontenot
Julia Lawall
Gautham R Shenoy
Greg Kroah-Hartman
Michael Neuling
Benjamin Herrenschmidt
Milton Miller
Linas Vepstas
will schmidt
Serge E. Hallyn
Olof Johansson
Grant Likely
Anton Blanchard
Jesper Juhl
Linus Torvalds
Sachin P. Sant
Mohan Kumar M
Jake Moilanen
Brian King
Jean Delvare
Olaf Hering
Kumar Gala
Arjan van de Ven
Alexey Dobriyan
Michal Ostrowski
Robert P. J. Day
Linus Torvalds