* 'for-linus/2640/i2c' of git://git.fluff.org/bjdooks/linux: (21 commits)
mach-ux500: set proper I2C platform data from MOP500s
i2c-nomadik: break out single messsage transmission
i2c-nomadik: reset the hw after status check
i2c-nomadik: remove the unnecessary delay
i2c-nomadik: change the TX and RX threshold
i2c-nomadik: add code to retry on timeout failure
i2c-nomadik: use pm_runtime API
i2c-nomadik: print abort cause only on abort tag
i2c-nomadik: correct adapter timeout initialization
i2c-nomadik: remove the redundant error message
i2c-nomadik: corrrect returned error numbers
i2c-nomadik: fix speed enumerator
i2c-nomadik: make i2c timeout specific per i2c bus
i2c-nomadik: add regulator support
i2c: i2c-sh_mobile bus speed platform data V2
i2c: i2c-sh_mobile clock string removal
i2c-eg20t: Support new device ML7223 IOH
i2c: tegra: Add de-bounce cycles.
i2c: tegra: fix repeated start handling
i2c: tegra: recover from spurious interrupt storm
...
These new platform-specific values can be used to set the fuzz parameter
passed to the input_set_abs_params() function for the ABS_X, ABS_Y and
ABS_PRESSURE axes.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This new parameter allows the polling frequency to be configured while
keeping the default of once every millisecond.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Depending on the quality of the touch panel, the time for the X-, X+, Y-
and Y+ inputs to settle may vary. The poll_delay parameter can be used
to override the default of 1 millisecond.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Kwangwoo Lee <kwangwoo.lee@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Finger touch events or very quick stylus events on low-quality panels
can cause the tsc2007 to read bogus values. Looking at oscilloscope
snapshots, this seems to be caused by the touch event disappearing
during the measurements. These bogus values result in misclicks, where
the X and Y values deviate from the real position.
Most of these misclicks can be filtered out by setting a low enough
threshold for the maximum resistance (which is loosely the inverse of
the pressure) allowed to consider a set of values valid. Since this
behaviour is largely dependent on the type and quality of the panel,
this commit introduces the max_rt parameter. The default value is kept
at MAX_12BIT.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds basic support for Freescale MPR121 capacitive touch
sensor. It's an i2c controller with up to 12 capacitance sensing inputs.
Product information (data sheet, application notes) can be found here:
http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MPR121
Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add support to the i2c-sh_mobile driver for setting
the I2C bus speed using platform data.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Introducing a driver for MADC on TWL4030 powerIC. MADC stands for monitoring
ADC. This driver monitors the real time conversion of analog signals like
battery temperature, battery cuurent etc.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In OMAP4 Blaze and Panda, 32KHz clock to WLAN is supplied from Phoenix
TWL6030. The 32KHz clock state (ON/OFF) is configured in
CLK32KG_CFG_[GRP, TRANS, STATE] register. This follows the same register
programming model as other regulators in TWL6030. So add CLK32KG as pseudo
regulator.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus/2639/i2c-2' of git://git.fluff.org/bjdooks/linux:
i2c-pxa2xx: Don't clear isr bits too early
i2c-pxa2xx: Fix register offsets
i2c-pxa2xx: pass of_node from platform driver to adapter and publish
i2c-pxa2xx: check timeout correctly
i2c-pxa2xx: add support for shared IRQ handler
i2c-pxa2xx: Add PCI support for PXA I2C controller
ARM: pxa2xx: reorganize I2C files
i2c-pxa2xx: use dynamic register layout
i2c-mxs: set controller to pio queue mode after reset
i2c-eg20t: support new device OKI SEMICONDUCTOR ML7213 IOH
i2c/busses: Add support for Diolan U2C-12 USB-I2C adapter
Configuration for ads1015 gain and datarate is possible via
devicetree or platform data.
This is a followup patch to previous ads1015 patches on Jean Delvares
tree.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch moves the platform data definition from
arch/arm/plat-pxa/include/plat/i2c.h to include/linux/i2c/pxa-i2c.h so
it can be accessed from x86 the same way as on ARM.
This change should make no functional change to the PXA code. The move
is verified by building the following defconfigs:
cm_x2xx_defconfig corgi_defconfig em_x270_defconfig ezx_defconfig
imote2_defconfig pxa3xx_defconfig spitz_defconfig zeus_defconfig
raumfeld_defconfig magician_defconfig mmp2_defconfig pxa168_defconfig
pxa910_defconfig
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (64 commits)
Input: tsc2005 - remove 'disable' sysfs attribute
Input: tsc2005 - add open/close
Input: tsc2005 - handle read errors from SPI layer
Input: tsc2005 - do not rearm timer in hardirq handler
Input: tsc2005 - don't use work for 'pen up' handling
Input: tsc2005 - do not use 0 in place of NULL
Input: tsc2005 - use true/false for boolean variables
Input: tsc2005 - hide selftest attribute if we can't reset
Input: tsc2005 - rework driver initialization code
Input: tsc2005 - set up bus type in input device
Input: tsc2005 - set up parent device
Input: tsc2005 - clear driver data after unbinding
Input: tsc2005 - add module description
Input: tsc2005 - remove driver banner message
Input: tsc2005 - remove incorrect module alias
Input: tsc2005 - convert to using dev_pm_ops
Input: tsc2005 - use spi_get/set_drvdata()
Input: introduce tsc2005 driver
Input: xen-kbdfront - move to drivers/input/misc
Input: xen-kbdfront - add grant reference for shared page
...
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (44 commits)
hwmon: (lineage-pem): Fix in1 voltage alarm sysfs attributes
hwmon/f71882fg: Add support for f71808e
hwmon/f71882fg: Add support for f71869f and f71869e
hwmon/f71882fg: Add support for f71889ed
hwmon/f71882fg: Break out test for auto pwm's controlled by digital readings
hwmon/f71882fg: Separate temp beep sysfs attr from the other temp sysfs attr
hwmon/f71882fg: Remove bogus temp2_type for certain models
hwmon/f71882fg: Make number of temps configurable
hwmon/f71882fg: Make creation of in sysfs attributes more generic
hwmon/f71882fg: Only allow negative auto point temps if fan_neg_temp is enabled
hwmon/f71882fg: Fix temp1 sensor type reporting
hwmon: (w83627ehf) Display correct temperature sensor labels for systems with NCT6775F
hwmon: (w83627ehf) Add fan debounce support for NCT6775F and NCT6776F
hwmon: (w83627ehf) Update Kconfig for W83677HG-B, NCT6775F and NCT6776F
hwmon: (w83627ehf) Store rpm instead of raw fan speed data
hwmon: (w83627ehf) Use 16 bit fan count registers if supported
hwmon: (w83627ehf) Add support for Nuvoton NCT6775F and NCT6776F
hwmon: (w83627ehf) Permit enabling SmartFan IV mode if configured at startup
hwmon: (w83627ehf) Convert register arrays to 16 bit, and convert access to pointers
hwmon: (w83627ehf) Remove references to datasheets which no longer exist
...
This driver adds support for hardware monitoring features of various PMBus
devices.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
audio_mclk can be queried from mfd driver. Therefore, it is not
needed in twl4030_codec_audio_data or in twl4030_codec_vibra_data
anymore.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds support for system-level suspend/resume to the driver.
Signed-off-by: Heungjun Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Different board have different requirements/setups so let's be more
flexible.
Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
As there is no common configuration settings that would work in every
situation, remove the fixed config data from driver code and add
config data to platform data.
Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Change prefixes from qt602240 to mxt to reflect that the driver supports
whole line of mXT touchscreens.
Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since the driver will be supporting whole range of Atmels mXT touchscreen
controllers we better rename it to atmel_mxt_ts.
Acked-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Declare the .phy_suspend function pointer to twl4030_usb_data structure.
OMAP internal phy suspend function will be hooked though this function
pointer to use in the transceiver driver.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Driver for Dallas Semiconductor DS620 temperature sensor and thermostat
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
Registering the twl6030-usb transceiver device as a child to twl6030 core.
Removed the NOP transceiver init call from board file.
Populated twl4030_usb_data platform data structure with the function
pointers for OMAP4430 internal PHY operation to be used by twl630-usb driver.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Unify adp5588-gpio and adp5588-keys common header defines (as per Andrew
Morton request). For consistency, move remaining defines and prefix
accordingly.
No functional changes.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Adding card detect callback function and card detect configuration
function for MMC1 Controller on OMAP4.
Card detect configuration function does initial configuration of the
MMC Control & PullUp-PullDown registers of Phoenix.
For MMC1 Controller, card detect interrupt source is
twl6030 which is non-gpio. The card detect call back function provides
card present/absent status by reading MMC Control register present
on twl6030.
Since OMAP4 doesn't use any GPIO line as used in OMAP3 for card detect,
the suspend/resume initialization which was done in omap_hsmmc_gpio_init
previously is moved to the probe thus making it generic for both OMAP3 &
OMAP4.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some modules already need to talk to at least PROTECT_KEY
register, while at that, add defines to the entire register
space.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some ADP5588 functions take a pointer to an i2c_client, but if the i2c
header doesn't happen to be included first, we hit the standard "struct
declared inside parameter list" warnings from gcc. So add a simple
forward decl of the i2c_client struct.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Common code interprets this as a signed value (a negative value is used to
request dynamic ID allocation), so make sure the platform data has proper
types to support that.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement irq_chip functionality on ADP5588/5587 GPIO expanders. Only
level sensitive interrupts are supported. Interrupts provided by this
irq_chip must be requested using request_threaded_irq().
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a driver for Avago APDS990X combined ALS and proximity sensor.
Interface is sysfs based. The driver uses interrupts to provide new data.
The driver supports pm_runtime and regulator frameworks.
See Documentation/misc-devices/apds990x.txt for details
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a driver for ROHM BH1770GLC and OSRAM SFH7770 combined ALS and
proximity sensor.
Interface is sysfs based. The driver uses interrupts to provide new data.
The driver supports pm_runtime and regulator frameworks.
See Documentation/misc-devices/bh1770glc.txt for details
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace the arbitrary software-reset call from the device-probe
method, because:
- It is defective. To work correctly, it should be two byte writes,
not a single word write. As it stands, it does nothing.
- Some devices with sx150x expanders installed have their NRESET pins
ganged on the same line, so resetting one causes the others to reset -
not a nice thing to do arbitrarily!
- The probe, usually taking place at boot, implies a recent hard-reset,
so a software reset at this point is just a waste of energy anyway.
Therefore, make it optional, defaulting to off, as this will match the
common case of probing at powerup and also matches the current broken
no-op behavior.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fairly simple conflicts, the most serious ones are the i.MX ones which I
suspect now need another rename.
Conflicts:
arch/arm/mach-mx2/clock_imx27.c
arch/arm/mach-mx2/devices.c
arch/arm/mach-omap2/board-rx51-peripherals.c
arch/arm/mach-omap2/board-zoom2.c
sound/soc/fsl/mpc5200_dma.c
sound/soc/fsl/mpc5200_dma.h
sound/soc/fsl/mpc8610_hpcd.c
sound/soc/pxa/spitz.c
Add support for exposing all GPIO pins as analog voltages. Though this is
not an ideal use of the chip, some hardware engineers may decide that the
LTC4245 meets their design requirements when studying the datasheet.
The GPIO pins are sampled in round-robin fashion, meaning that a slow
reader will see stale data. A userspace application can detect this,
because it will get -EAGAIN when reading from a sysfs file which contains
stale data.
Users can choose to use this feature on a per-chip basis by using either
platform data or the OF device tree (where applicable).
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: I2C bus multiplexer driver pca954x
i2c: Multiplexed I2C bus core support
i2c: Use a separate mutex for userspace client lists
i2c: Make i2c_default_probe self-sufficient
i2c: Drop dummy variable
i2c: Move adapter locking helpers to i2c-core
V4L/DVB: Use custom I2C probing function mechanism
i2c: Add support for custom probe function
i2c-dev: Use memdup_user
i2c-dev: Remove unnecessary kmalloc casts
This patch extends the ASoC API to allow sound cards to have more than one
CODEC and more than one platform DMA controller. This is achieved by dividing
some current ASoC structures that contain both driver data and device data into
structures that only either contain device data or driver data. i.e.
struct snd_soc_codec ---> struct snd_soc_codec (device data)
+-> struct snd_soc_codec_driver (driver data)
struct snd_soc_platform ---> struct snd_soc_platform (device data)
+-> struct snd_soc_platform_driver (driver data)
struct snd_soc_dai ---> struct snd_soc_dai (device data)
+-> struct snd_soc_dai_driver (driver data)
struct snd_soc_device ---> deleted
This now allows ASoC to be more tightly aligned with the Linux driver model and
also means that every ASoC codec, platform and (platform) DAI is a kernel
device. ASoC component private data is now stored as device private data.
The ASoC sound card struct snd_soc_card has also been updated to store lists
of it's components rather than a pointer to a codec and platform. The PCM
runtime struct soc_pcm_runtime now has pointers to all its components.
This patch adds DAPM support for ASoC multi-component and removes struct
snd_soc_socdev from DAPM core. All DAPM calls are now made on a card, codec
or runtime PCM level basis rather than using snd_soc_socdev.
Other notable multi-component changes:-
* Stream operations now de-reference less structures.
* close_delayed work() now runs on a DAI basis rather than looping all DAIs
in a card.
* PM suspend()/resume() operations can now handle N CODECs and Platforms
per sound card.
* Added soc_bind_dai_link() to bind the component devices to the sound card.
* Added soc_dai_link_probe() and soc_dai_link_remove() to probe and remove
DAI link components.
* sysfs entries can now be registered per component per card.
* snd_soc_new_pcms() functionailty rolled into dai_link_probe().
* snd_soc_register_codec() now does all the codec list and mutex init.
This patch changes the probe() and remove() of the CODEC drivers as follows:-
o Make CODEC driver a platform driver
o Moved all struct snd_soc_codec list, mutex, etc initialiasation to core.
o Removed all static codec pointers (drivers now support > 1 codec dev)
o snd_soc_register_pcms() now done by core.
o snd_soc_register_dai() folded into snd_soc_register_codec().
CS4270 portions:
Acked-by: Timur Tabi <timur@freescale.com>
Some TLV320aic23 and Cirrus platform fixes.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
TI CODEC and OMAP fixes
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Samsung platform and misc fixes :-
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
MPC8610 and PPC fixes.
Signed-off-by: Timur Tabi <timur@freescale.com>
i.MX fixes and some core fixes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
J4740 platform fixes:-
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
CC: Tony Lindgren <tony@atomide.com>
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
CC: Kuninori Morimoto <morimoto.kuninori@renesas.com>
CC: Daniel Gloeckner <dg@emlix.com>
CC: Manuel Lauss <mano@roarinelk.homelinux.net>
CC: Mike Frysinger <vapier.adi@gmail.com>
CC: Arnaud Patard <apatard@mandriva.com>
CC: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch allows exporting GPIO pins not used by the keypad itself
to be accessible from elsewhere.
Signed-off-by: Xiaolong Chen <xiao-long.chen@motorola.com>
Signed-off-by: Yuanbo Ye <yuan-bo.ye@motorola.com>
Signed-off-by: Tao Hu <taohu@motorola.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The chip's full name is AT42QT602240 or ATMXT224. This is a capacitive
touchscreen supporting 10-contact multitouch and using I2C interface.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A column or row configured as a GPI can be programmed to be part
of the key event table and therefore also capable of generating a
key event interrupt. A key event interrupt caused by a GPI follows
the same process flow as a key event interrupt caused by a key
press. GPIs configured as part of the key event table allow single
key switches and other GPI interrupts to be monitored. As part of
the event table, GPIs are represented by the decimal value 97 (0x61
or 1100001) through the decimal value 114 (0x72 or 1110010). See
table below for GPI event number assignments for rows and columns.
GPI Event Number Assignments for Rows
Row0 Row1 Row2 Row3 Row4 Row5 Row6 Row7
97 98 99 100 101 102 103 104
GPI Event Number Assignments for Cols
Col0 Col1 Col2 Col3 Col4 Col5 Col6 Col7 Col8 Col9
105 106 107 108 109 110 111 112 113 114
Signed-off-by: Xiaolong Chen <xiao-long.chen@motorola.com>
Signed-off-by: Yuanbo Ye <yuan-bo.ye@motorola.com>
Signed-off-by: Tao Hu <taohu@motorola.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
gpiolib doesn't need to modify the names and I assume most initializers
use string constants that shouldn't be modified anyhow.
[akpm@linux-foundation.org: fix drivers/gpio/cs5535-gpio.c]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Kevin Wells <kevin.wells@nxp.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most of the GPIO expanders supported by the max732x driver have interrupt
generation capability by reporting changes on input pins through an INT#
pin. This patch implements the irq_chip functionnality (edge detection
only).
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jebediah Huang <jebediah.huang@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The ADP8860 combines a programmable backlight LED charge pump driver with
automatic phototransistor control.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (250 commits)
ALSA: hda: Storage class should be before const qualifier
ASoC: tpa6130a2: Remove CPVSS and HPVdd supplies
ASoC: tpa6130a2: Define output pins with SND_SOC_DAPM_OUTPUT
ASoC: sdp4430 - add sdp4430 pcm ops to DAI.
ASoC: TWL6040: Enable earphone path in codec
ASoC: SDP4430: Add support for Earphone speaker
ASoC: SDP4430: Add sdp4430 machine driver
ASoC: tlv320dac33: Avoid powering off while in BIAS_OFF
ASoC: tlv320dac33: Use dev_dbg in dac33_hard_power function
ALSA: sound/pci/asihpi: Use kzalloc
ALSA: hdmi - dont fail on extra nodes
ALSA: intelhdmi - add id for the CougarPoint chipset
ALSA: intelhdmi - user friendly codec name
ALSA: intelhdmi - add dependency on SND_DYNAMIC_MINORS
ALSA: asihpi: incorrect range check
ALSA: asihpi: testing the wrong variable
ALSA: es1688: add pedantic range checks
ARM: McBSP: Add support for omap4 in McBSP driver
ARM: McBSP: Fix request for irq in OMAP4
OMAP: McBSP: Add 32-bit mode support
...
Correction for chips:
twl6030 is Phoenix Power chip
twl6040 is Phoenix Audio chip
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
New function twl4030_remove_script(u8 flags) takes a script type as
defined in twl.h and prevents any script already loaded in that position
from running. This is accomplished by programming SEQ_ADD_* to 0x3f,
the END_OF_SCRIPT value, where SEQ_ADD_* is determined by flags.
(Future) users of this function include OMAP board files for machines
facing a race condition between sleep and warm reset.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add base address for generic slave ID0, ID1, ID2
and introduced one more entry to align RTC module number between
twl4030 and twl6030
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch disables TWL4030/5030 I2C1 adn I2C4(SR) internal pull-up, to
use only the external HW resistor >=470 Ohm for the assured
functionality in HS mode.
While testing the I2C in High Speed mode, it was discovered that
without a proper pull-up resistor, there is data corruption during
multi-byte transfer. RTC(time_set) test case was used for testing.
From the analysis done, it was concluded that ideally we need a
pull-up of 1.6k Ohm(recomended) or atleast 470 Ohm or greater for
assured performance in HS mode.
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Allen Pais <allen.pais@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The TWL4030_BCI_BATTERY config option originates from a patch to the
omap git tree. However inclusion in linux was seemingly rejected and
the functionality nears inclusion under a different name so this
removes the bits of the old version that made it into the mainline
kernel again.
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Most of the GPIO expanders controlled by the pca953x driver are able to
report changes on the input pins through an *INT pin.
This patch implements the irq_chip functionality (edge detection only).
The driver has been tested on an Arcom Zeus.
[akpm@linux-foundation.org: the compiler does inlining for us nowadays]
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Nate Case <ncase@xes-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
linux/i2c/pca953x.h is a very bare include file. Fix check for multiple
includes of linux/i2c/pca953x.h, and add dependent includes into the
header file.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to have TWL6030 CODEC driver as a platform driver, codec data
should be passed through twl_platform_data structure.
For twl6030 audio codec, the following data may be passed:
- audpwron_gpio: gpio line used to power-up/down the codec. A low-to-high
transition powers codec up. Setting audpwron_gpio to a negative value
means that codec will use manual power sequence instead of automatic
sequence
- naudint_irq: irq line for audio interrupt. twl6030 drives NAUDINT line
to low when an interrupt (codec ready, plug insertion/removal, etc) is
detected
However, codec driver can operate if any or none of them are passed.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds initial support for creating twl6030 PMIC
specific voltage regulators in the twl mfd driver.
Board specific regulator configurations will have to be passed from
respective board files.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch updates the regulator driver to add support
for TWL6030 PMIC specific LDO regulators.
SMPS resources are not yet supported for TWL6030 and
also .set_mode and .get_status for LDO's are yet to
be implemented for TWL6030.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds support for phoenix interrupt framework. New iInterrupt
status register A, B, C are introduced in Phoenix and are cleared on write.
Due to the differences in interrupt handling with respect to TWL4030,
twl6030-irq.c is created for TWL6030 PMIC
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch renames function names like twl4030_i2c_write_u8,
twl4030_i2c_read_u8 to twl_i2c_write_u8, twl_i2c_read_u8
and also common variable in twl-core.c
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add all twl4030 regulators to the twl4030 mfd driver and
twl4030_platform_data
Signed-off-by: Juha Keski-Saari <ext-juha.1.keski-saari@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TWL5031 introduces two new interrupts in PIH. Moreover, BCI
has changed remarkably and, thus, it's disabled when TWL5031
is in use.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add function to allow the configuation fo the VDCDC2 register by
external users, to allow changing of the standard and low-power
running modes.
This is needed, for example, for the Simtec IM2440D20 where we need
to use the low-power mode to shutdown the LDO/DCDC that are not needed
during suspend (saving substantial power) and the runtime use of the
low-power mode to change VCore.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allows TWL's 32kHz oscillator to go in low-power mode when
main battery voltage is running low.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The code tries to skip values initialized with -1, but since the values
are unsigned the comparison is always true.
The patch eliminates the following compiler warnings:
drivers/mfd/twl4030-power.c: In function 'twl4030_configure_resource':
drivers/mfd/twl4030-power.c:338: warning: comparison is always true due to
limited range of data type
drivers/mfd/twl4030-power.c:358: warning: comparison is always true due to
limited range of data type
drivers/mfd/twl4030-power.c:363: warning: comparison is always true due to
limited range of data type
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The <RESOURCE>_REMAP register allows configuration of the <RESOURCE> in case
of a sleep or off transition.
Allow this property of resources to be configured (through twl4030_resconfig)
and add code to parse these values to program the registers accordingly.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add audio_mclk to the platform data struct for the
twl4030-codec MFD driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
New MFD child to twl4030 MFD device.
Reason for the twl4030_codec MFD: the vibra control is actually in the codec
part of the twl4030. If both the vibra and the audio functionality is needed
from the twl4030 at the same time, than they need to control the codec power
and APLL at the same time without breaking the other driver.
Also these two has to be able to work without the need for the other driver.
This MFD device will be used by the drivers, which needs resources
from the twl4030 codec like audio and vibra.
The platform specific configuration data is passed along to the
child drivers (audio, vibra).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The original driver was written with the KEY() macro defined as (col,
row) instead of (row, col) as defined by the matrix keypad
infrastructure. So the keymap was defined accordingly. Since the
driver that was merged upstream uses the matrix keypad infrastructure,
modify the keymap accordingly.
While we are at it, fix the comments in twl4030.h and define
PERSISTENT_KEY as (r,c) instead of (c, r)
Tested on a RX51 (N900) device.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The MELPAS MCS-5000 is the touchscreen controller. The overview of this
controller can see at the following website:
http://www.melfas.com/product/product01.asp?k_r=eng_
This driver is tested on s3c6410 NCP board and supports only the i2c
interface.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The TWL4030/5030 family of multifunction devices allows board-specific
control of the the various regulators, clock and reset lines through
'scripts' that are loaded into its memory. This allows for Dynamic Power
Switching (DPS).
Implement board-independent core support for DPS that is then used by
board-specific code to load custom DPS scripts.
Signed-off-by: Amit Kucheria <amit.kucheria@verdurent.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add a driver for the keypad controller on TWL4030 family chips.
These support up to an 8x8 key matrix. The TWL4030 multifunction
chips are mostly used on OMAP3 (or OMAP 2430) based boards.
[dtor@mail.ru: switch to matrix-keypad framework, fix changing
keymap from userspace]
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (35 commits)
Input: add driver for Synaptics I2C touchpad
Input: synaptics - add support for reporting x/y resolution
Input: ALPS - handle touchpoints buttons correctly
Input: gpio-keys - change timer to workqueue
Input: ads7846 - pin change interrupt support
Input: add support for touchscreen on W90P910 ARM platform
Input: appletouch - improve finger detection
Input: wacom - clear Intuos4 wheel data when finger leaves proximity
Input: ucb1400 - move static function from header into core
Input: add driver for EETI touchpanels
Input: ads7846 - more detailed model name in sysfs
Input: ads7846 - support swapping x and y axes
Input: ati_remote2 - use non-atomic bitops
Input: introduce lm8323 keypad driver
Input: psmouse - ESD workaround fix for OLPC XO touchpad
Input: tsc2007 - make sure platform provides get_pendown_state()
Input: uinput - flush all pending ff effects before destroying device
Input: simplify name handling for certain input handles
Input: serio - do not use deprecated dev.power.power_state
Input: wacom - add support for Intuos4 tablets
...
Add support to the PCA953x driver to use the GPIOLIB naming facility for
GPIOs.
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lm8323 is the keypad driver used in n810 device.
[akpm@linux-foundation.org: coding-style fixes]
[dtor@mail.ru: various cleanups]
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Support for the s6000 on-chip i2c controller.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6: (32 commits)
regulator: twl4030 VAUX3 supports 3.0V
regulator: Support disabling of unused regulators by machines
regulator: Don't increment use_count for boot_on regulators
twl4030-regulator: expose VPLL2
regulator: refcount fixes
regulator: Don't warn if we failed to get a regulator
regulator: Allow boot_on regulators to be disabled by clients
regulator: Implement list_voltage for WM835x LDOs and DCDCs
twl4030-regulator: list more VAUX4 voltages
regulator: Don't warn on omitted voltage constraints
regulator: Implement list_voltage() for WM8400 DCDCs and LDOs
MMC: regulator utilities
regulator: twl4030 voltage enumeration (v2)
regulator: twl4030 regulators
regulator: get_status() grows kerneldoc
regulator: enumerate voltages (v2)
regulator: Fix get_mode() for WM835x DCDCs
regulator: Allow regulators to set the initial operating mode
regulator: Suggest use of datasheet supply or pin names for consumers
regulator: email - update email address and regulator webpage.
...
In the case of at24, the platform code registers a 'setup' callback with
the at24_platform_data. When the at24 driver detects an EEPROM, it fills
out the read and write functions of the memory_accessor and calls the
setup callback passing the memory_accessor struct. The platform code can
then use the read/write functions in the memory_accessor struct for
reading and writing the EEPROM.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support most of the LDO regulators in the twl4030 family chips.
In the case of LDOs supporting MMC/SD, the voltage controls are
used; but in most other cases, the regulator framework is only
used to enable/disable a supplies, conserving power when a given
voltage rail is not needed.
The drivers/mfd/twl4030-core.c code already sets up the various
regulators according to board-specific configuration, and knows
that some chips don't provide the full set of voltage rails.
The omitted regulators are intended to be under hardware control,
such as during the hardware-mediated system powerup, powerdown,
and suspend states. Unless/until software hooks are known to
be safe, they won't be exported here.
These regulators implement the new get_status() operation, but
can't realistically implement get_mode(); the status output is
effectively the result of a vote, with the relevant hardware
inputs not exposed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (29 commits)
Input: i8042 - add Dell Vostro 1510 to nomux list
Input: gtco - use USB endpoint API
Input: add support for Maple controller as a joystick
Input: atkbd - broaden the Dell DMI signatures
Input: HIL drivers - add MODULE_ALIAS()
Input: map_to_7segment.h - convert to __inline__ for userspace
Input: add support for enhanced rotary controller on pxa930 and pxa935
Input: add support for trackball on pxa930 and pxa935
Input: add da9034 touchscreen support
Input: ads7846 - strict_strtoul takes unsigned long
Input: make some variables and functions static
Input: add tsc2007 based touchscreen driver
Input: psmouse - add module parameters to control OLPC touchpad delays
Input: i8042 - add Gigabyte M912 netbook to noloop exception table
Input: atkbd - Samsung NC10 key repeat fix
Input: atkbd - add keyboard quirk for HP Pavilion ZV6100 laptop
Input: libps2 - handle 0xfc responses from devices
Input: add support for Wacom W8001 penabled serial touchscreen
Input: synaptics - report multi-taps only if supported by the device
Input: add joystick driver for Walkera WK-0701 RC transmitter
...
Provide a static debounce configuration mechanism for twl4030 GPIOs,
replacing the previous dynamic one. The single user of that mechanism was
for MMC card detect debouncing.
Boards can provide a bitmask saying which GPIOs to debounce (30 msec).
It's always enabled for pins with the MMC card-detect/VMMCx link active,
so most boards won't need to set the debounce mask.
This is a net code shrink, including runtime footprint.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Basic MFD framework for the MSP430 microcontroller firmware used
on the dm355evm board:
- Provides an interface for other drivers: register read/write
utilities, and register declarations.
- Directly exports:
* Many signals through the GPIO framework
+ LEDs
+ SW6 through gpio sysfs
+ NTSC/nPAL jumper through gpio sysfs
+ ... more could be added later, e.g. MMC signals
* Child devices:
+ LEDs, via leds-gpio child (and default triggers)
+ RTC, via rtc-dm355evm child device
+ Buttons and IR control, via dm355evm_keys
- Supports power-off system call. Use the reset button to power
the board back up; the power supply LED will be on, but the
MSP430 waits to re-activate the regulators.
- On probe() this:
* Announces firmware revision
* Turns off the banked LEDs
* Exports the resources noted above
* Hooks the power-off support
* Muxes tvp5146 -or- imager for video input
Unless the new tvp514x driver (tracked for mainline) is configured,
this assumes that some custom imager driver handles video-in.
This completely ignores the registers reporting the output voltages
on the various power supplies. Someone could add a hwmon interface
if that seems useful.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This contains two bugfixes to the initial twl4030 regulator
support patch related to USB:
(a) always overwrite the old list of consumers ... else
the regulator handles all use the same "usb1v5" name;
(b) don't set up the "usbcp" regulator, which turns out
to be managed through separate controls, usually ULPI
directly from the OTG controller.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Initial code to create twl4030 voltage regulator devices, using
the new regulator framework. Note that this now starts to care
what name is used to declare the TWL chip:
- TWL4030 is the "old" chip; newer ones have a bigger variety
of VAUX2 voltages.
- TWL5030 is the core "new" chip; TPS65950 is its catalog version.
- The TPS65930 and TPS65920 are cost-reduced catalog versions of
TWL5030 parts ... fewer regulators, no battery charger, etc.
Board-specific regulator configuration should be provided, listing
which regulators are used and their constraints (e.g. 1.8V only).
Code that could ("should"?) leverage the regulator stuff includes
TWL4030 USB transceiver support and MMC glue, LCD support for the
3430SDP and Labrador boards, and S-Video output.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Finish removing dependency of TWL driver stack on platform-specific
IRQ definitions ... and remove the build dependency on OMAP.
This lets the TWL4030 code be included in test builds for most
platforms, and will make it easier for non-OMAP folk to update
most of this code for new APIs etc.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Minor change to the TWL4030 utility interface: support reads
of all 256 bytes in each register bank (vs just 255). This
can help when debugging, but is otherwise a NOP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This drive has been tested on ARM9 based SoC - MV86XX.
Signed-off-by: Kwangwoo Lee <kwangwoo.lee@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- Move it into a separate file; clean and streamline it
- Restructure the init code for reuse during secondary dispatch
- Support both levels (primary, secondary) of IRQ dispatch
- Use a workqueue for irq mask/unmask and trigger configuration
Code for two subchips currently share that secondary handler code.
One is the power subchip; its IRQs are now handled by this core,
courtesy of this patch. The other is the GPIO module, which will
be supported through a later patch.
There are also minor changes to the header file, mostly related
to GPIO support; nothing yet in mainline cares about those. A
few references to OMAP-specific symbols are disabled; when they
can all be removed, the TWL4030 support ceases being OMAP-specific.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch adds the core of the TWL4030 driver, which supports
chips including the TPS65950. These chips are multi-function; see
http://focus.ti.com/docs/prod/folders/print/tps65950.html
Public specs are in the works. For now, the block diagram on
the second page of the datasheet is fairly informative.
There are some known issues with this core code. Most notably,
the IRQ dispatching needs simplification (to use more of genirq),
generalization (integrating support for secondary IRQ dispatch
as well as primary, and removing the build dependency on OMAP),
and then probably updating to leverage threaded IRQ support
(expected to arrive in mainline "soon").
Once the core is in mainline, drivers for other parts of this
chip can follow its lead and start swimming upstream too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This adds a driver supporting a family of I2C port expanders from Maxim,
which includes the MAX7319 and MAX7320-7327 chips.
[dbrownell@users.sourceforge.net: minor fixes]
Signed-off-by: Jack Ren <jack.ren@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new-style driver for most I2C EEPROMs, giving sysfs read/write
access to their data. Tested with various chips and clock rates.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove the old driver_name/type scheme for i2c driver matching. Only the
standard aliasing model will be used from now on.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Make the tps65010 driver use gpiolib to expose its GPIOs.
Note: This patch will get merged via omap tree instead of I2C
as it will cause some board updates. This has been discussed
at on the I2C list:
http://lists.lm-sensors.org/pipermail/i2c/2008-March/003031.html
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: i2c@lm-sensors.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
This second part of an extension to support more pca953x chips renames the C
and Kconfig symbols. All affected files were updated by sed, except for a
couple of obvious exceptions. It also updates the Kconfig helptext.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
First part of an extension to let the pca9539 driver support more chips,
starting with pca9534, pca9535, pca9536, pca9537, and pca9538.
This renames the files and modifies the Makefile.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a new-style I2C driver with basic support for the sixteen bit
PCA9539 GPIO expanders. These chips have multiple registers, push-pull output
drivers, and (not supported in this patch) pin change interrupts.
Board-specific code must provide "pca9539_platform_data" with each chip's
"i2c_board_info". That provides the GPIO numbers to be used by that chip, and
callbacks for board-specific setup/teardown logic.
Derived from drivers/i2c/chips/pca9539.c (which has no current known users).
This is faster and simpler; it uses 16-bit register access, and cache the
OUTPUT and DIRECTION registers for fast access
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a new-style I2C driver for most common 8 and 16 bit I2C based
"quasi-bidirectional" GPIO expanders: pcf8574 or pcf8575, and several
compatible models (mostly faster, supporting I2C at up to 1 MHz).
The driver exposes the GPIO signals using the platform-neutral GPIO
programming interface, so they are easily accessed by other kernel code. The
lack of such a flexible kernel API has been a big factor in the proliferation
of board-specific drivers for these chips... stuff that rarely makes it
upstream since it's so ugly. This driver will let such boards use standard
calls.
Since it's a new-style driver, these devices must be configured as part of
board-specific init. That eliminates the need for error-prone manual
configuration of module parameters, and makes compatibility with legacy
drivers (pcf8574.c, pc8575.c) for these chips easier (there's a clear
either/or disjunction).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the tps65010 header file from the OMAP arch directory to the
more generic <linux/i2c/...> directory, and remove the spurious
dependency of this driver on OMAP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Linus Torvalds
Thierry Reding
Zhang Jiejing
Magnus Damm
Keerthy
Balaji T K
Dirk Eibach
Sebastian Andrzej Siewior
Guenter Roeck
stigge@antcom.de
Ilkka Koskinen
Heungjun Kim
Iiro Valkonen
Dmitry Torokhov
Hema HK
Greg Kroah-Hartman
Michael Hennerich
kishore kadiyala
Felipe Balbi
Samu Onkalo
Takashi Iwai
Gregory Bean
Mark Brown
Ira W. Snyder
Liam Girdwood
Michael Lawnick
Xiaolong Chen
Joonyoung Shim
Xiaolong CHEN
Uwe Kleine-König
Marc Zyngier
Thomas Weber
Olaya, Margarita
Mike Turquette
Moiz Sonasath
Christoph Egger
Olof Johansson
Misael Lopez Cruz
Rajendra Nayak
Santosh Shilimkar
Juha Keski-Saari
Ben Dooks
Aaro Koskinen
Amit Kucheria
Peter Ujfalusi
David Brownell
Daniel Silverstone
Felipe Balbi
Oskar Schirmer
Kevin Hilman
Kwangwoo Lee
Eric Miao
Wolfram Sang
Jean Delvare
David Brownell
Guennadi Liakhovetski