The Nomadik variant has a few special quirks that need to be respected
to make the driver work:
- The block need to be clocked during writing of the TIMn registers
or the bus will stall.
- Special bits in the control register select how many of the output
display lines get activated.
- Special bits in the control register select how to manage the
different 565 and 5551 modes.
- There is a packed 24bit graphics mode, i.e 888 pixels can be stored
in memory is three consecutive bytes, not evenly aligned to a 32bit
word.
This patch uses the vendor data pointer from the AMBA matching mechanism
to track the quirks for this variant, and adds two hooks that variants
can use to initialize boards and panels during start-up. These will
later be used to adopt a Nomadik board profile.
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There are CLCDs connected with the pads in BGR rather than RGB
order. It really doesn't matter since the CLCD has a flag and
a bit to switch the position of the RGB and BGR components.
This is needed to put something logical into the
arm,pl11x,tft-r0g0b0-pads property of the device tree on the
Nomadik which will then be <16 8 0>.
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If the device is probed from device tree, we can support
backlight. This is used with some systems such as the
ST Microelectronics Nomadik.
We have to add HAS_IOMEM to the dependencies of CLCD since
the backlight class device will now be selected, and if it
gets selected on an arch that does not have IOMEM,
compilation will fail.
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The ARM CLCD PL110 controller in TFT mode provides two output formats
based on whether the controller is in 24bpp mode or not - either 5551
or 888. PL111 augments this with a 444 and 565 modes.
Some implementations provide an external MUX on the PL110 output to
reassign the bits to achieve 565 mode.
Provide a system of capability flags to allow the CLCD driver to work
out what is supported by each panel and board, and therefore which
display formats are permitted.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Instead of matching the entire peripheral ID, match against
just the part number using the amba_xxx() macros.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the clock enable/disable tracking in the AMBA CLCD driver so
that the driver doesn't try to disable an already disabled clock,
thereby causing the clock (if shared) to become unbalanced.
This resolves a problem with CLCD on LPC32xx ARM platforms.
Reported-by: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On PL111, as found on Realview and other platforms, these registers are
always arranged as CNTL then IENB. On PL110, these registers are IENB
then CNTL, except on Versatile platforms.
Re-arrange the handling of these register swaps so that PL111 always
gets it right without resorting to ifdefs, leaving the only case needing
special handling being PL110 on Versatile.
Fill out amba/clcd.h with the PL110/PL111 register definition
differences in case someone tries to use the PL110 specific definitions
on PL111.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
Starting with PL111, the 5551 or 565 modes can be configured in the
primecell's control register directly. This patch detects the required mode
and sets the correct value.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the ARM AMBA bus is used on MIPS as well as ARM, we need
to make the bus available for other architectures to use. Move
the AMBA include files from include/asm-arm/hardware/ to
include/linux/amba/
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eric Anholt
Linus Walleij
Lucas De Marchi
Russell King
David Woodhouse
Catalin Marinas
Russell King