This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
clean ups from that branch.
This code solves the issue of performing stack dumps from NMI context.
The issue is that printk() is not safe from NMI context as if the NMI
were to trigger when a printk() was being performed, the NMI could
deadlock from the printk() internal locks. This has been seen in practice.
With lots of review from Petr Mladek, this code went through several
iterations, and we feel that it is now at a point of quality to be
accepted into mainline.
Here's what is contained in this patch set:
o Creates a "seq_buf" generic buffer utility that allows a descriptor
to be passed around where functions can write their own "printk()"
formatted strings into it. The generic version was pulled out of
the trace_seq() code that was made specifically for tracing.
o The seq_buf code was change to model the seq_file code. I have
a patch (not included for 3.19) that converts the seq_file.c code
over to use seq_buf.c like the trace_seq.c code does. This was done
to make sure that seq_buf.c is compatible with seq_file.c. I may
try to get that patch in for 3.20.
o The seq_buf.c file was moved to lib/ to remove it from being dependent
on CONFIG_TRACING.
o The printk() was updated to allow for a per_cpu "override" of
the internal calls. That is, instead of writing to the console, a call
to printk() may do something else. This made it easier to allow the
NMI to change what printk() does in order to call dump_stack() without
needing to update that code as well.
o Finally, the dump_stack from all CPUs via NMI code was converted to
use the seq_buf code. The caller to trigger the NMI code would wait
till all the NMIs finished, and then it would print the seq_buf
data to the console safely from a non NMI context.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUhbrnAAoJEEjnJuOKh9ldsCoIAJ3sKIJ5B3jxJJTCHPAx/lZD
GVbV1J1mu4kTAZuhJZOAxW8D6PZGZMyEjg0y6ScDEnBGcjAZ9gTiWCdakPktf9EX
GfaPPqwiL9dZ18J9Qc6uR+7M1Ffpzzwbcc6lJrpoTcjRgkoH9wCiLS9ozFQyYzWb
/7m5UbUM/PIk9WAjLYXPW6UUVtPTPT0RdEQKofMGTeah+vgqj4TXCOROdlxsXXWF
77vqBvPd5TUPWFH9ftzJGDtZS8SroXVKCu3fZIqHgzAU0yqwVtH/JzDTy9u2UYhX
GzDEPeAIdp6m6Uyc406VuIf1QW0gfBgmA0ir80vFoP27uFMM6j5HlF7azgQfx34=
=YBgA
-----END PGP SIGNATURE-----
Merge tag 'trace-seq-buf-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull nmi-safe seq_buf printk update from Steven Rostedt:
"This code is a fork from the trace-3.19 pull as it needed the
trace_seq clean ups from that branch.
This code solves the issue of performing stack dumps from NMI context.
The issue is that printk() is not safe from NMI context as if the NMI
were to trigger when a printk() was being performed, the NMI could
deadlock from the printk() internal locks. This has been seen in
practice.
With lots of review from Petr Mladek, this code went through several
iterations, and we feel that it is now at a point of quality to be
accepted into mainline.
Here's what is contained in this patch set:
- Creates a "seq_buf" generic buffer utility that allows a descriptor
to be passed around where functions can write their own "printk()"
formatted strings into it. The generic version was pulled out of
the trace_seq() code that was made specifically for tracing.
- The seq_buf code was change to model the seq_file code. I have a
patch (not included for 3.19) that converts the seq_file.c code
over to use seq_buf.c like the trace_seq.c code does. This was
done to make sure that seq_buf.c is compatible with seq_file.c. I
may try to get that patch in for 3.20.
- The seq_buf.c file was moved to lib/ to remove it from being
dependent on CONFIG_TRACING.
- The printk() was updated to allow for a per_cpu "override" of the
internal calls. That is, instead of writing to the console, a call
to printk() may do something else. This made it easier to allow
the NMI to change what printk() does in order to call dump_stack()
without needing to update that code as well.
- Finally, the dump_stack from all CPUs via NMI code was converted to
use the seq_buf code. The caller to trigger the NMI code would
wait till all the NMIs finished, and then it would print the
seq_buf data to the console safely from a non NMI context
One added bonus is that this code also makes the NMI dump stack work
on PREEMPT_RT kernels. As printk() includes sleeping locks on
PREEMPT_RT, printk() only writes to console if the console does not
use any rt_mutex converted spin locks. Which a lot do"
* tag 'trace-seq-buf-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
x86/nmi: Fix use of unallocated cpumask_var_t
printk/percpu: Define printk_func when printk is not defined
x86/nmi: Perform a safe NMI stack trace on all CPUs
printk: Add per_cpu printk func to allow printk to be diverted
seq_buf: Move the seq_buf code to lib/
seq-buf: Make seq_buf_bprintf() conditional on CONFIG_BINARY_PRINTF
tracing: Add seq_buf_get_buf() and seq_buf_commit() helper functions
tracing: Have seq_buf use full buffer
seq_buf: Add seq_buf_can_fit() helper function
tracing: Add paranoid size check in trace_printk_seq()
tracing: Use trace_seq_used() and seq_buf_used() instead of len
tracing: Clean up tracing_fill_pipe_page()
seq_buf: Create seq_buf_used() to find out how much was written
tracing: Add a seq_buf_clear() helper and clear len and readpos in init
tracing: Convert seq_buf fields to be like seq_file fields
tracing: Convert seq_buf_path() to be like seq_path()
tracing: Create seq_buf layer in trace_seq
to the trace_seq code. It also removed the return values to the
trace_seq_*() functions and use trace_seq_has_overflowed() to see if
the buffer filled up or not. This is similar to work being done to the
seq_file code as well in another tree.
Some of the other goodies include:
o Added some "!" (NOT) logic to the tracing filter.
o Fixed the frame pointer logic to the x86_64 mcount trampolines
o Added the logic for dynamic trampolines on !CONFIG_PREEMPT systems.
That is, the ftrace trampoline can be dynamically allocated
and be called directly by functions that only have a single hook
to them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUhbLGAAoJEEjnJuOKh9ldRV4H/3NcLbgGB2iu96la1zdYE6pG
Q7cDJMxXK80YIIL70h9G0IItcD4t62LMb72lfBnMGRj3msgFb3AgISW57EuI0Pxk
xk24wuIPoTG2S7v9sc3SboNFwO8qbtIjxD2OBmqIUrGo2sZIiGjyj3gX7mCY3uzL
WB2bUOSFz/22OgaANinR5EELHA3pZZCf54Vz1K9ndmtK0xp0j1a7xJShD6TrMdYv
mZ3zH5ViIhW4A3mdcMceh6fy2JLQAiEKF0uPTvcMMz7NlVul0mxyL/+10P7AE/3R
Ehw4fzmm4NDshPDtBOkKH0LsppgXzuItFuQUTpact3JlqTg++bV6onSsrkt1hlY=
=Z7Cm
-----END PGP SIGNATURE-----
Merge tag 'trace-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"There was a lot of clean ups and minor fixes. One of those clean ups
was to the trace_seq code. It also removed the return values to the
trace_seq_*() functions and use trace_seq_has_overflowed() to see if
the buffer filled up or not. This is similar to work being done to
the seq_file code as well in another tree.
Some of the other goodies include:
- Added some "!" (NOT) logic to the tracing filter.
- Fixed the frame pointer logic to the x86_64 mcount trampolines
- Added the logic for dynamic trampolines on !CONFIG_PREEMPT systems.
That is, the ftrace trampoline can be dynamically allocated and be
called directly by functions that only have a single hook to them"
* tag 'trace-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (55 commits)
tracing: Truncated output is better than nothing
tracing: Add additional marks to signal very large time deltas
Documentation: describe trace_buf_size parameter more accurately
tracing: Allow NOT to filter AND and OR clauses
tracing: Add NOT to filtering logic
ftrace/fgraph/x86: Have prepare_ftrace_return() take ip as first parameter
ftrace/x86: Get rid of ftrace_caller_setup
ftrace/x86: Have save_mcount_regs macro also save stack frames if needed
ftrace/x86: Add macro MCOUNT_REG_SIZE for amount of stack used to save mcount regs
ftrace/x86: Simplify save_mcount_regs on getting RIP
ftrace/x86: Have save_mcount_regs store RIP in %rdi for first parameter
ftrace/x86: Rename MCOUNT_SAVE_FRAME and add more detailed comments
ftrace/x86: Move MCOUNT_SAVE_FRAME out of header file
ftrace/x86: Have static tracing also use ftrace_caller_setup
ftrace/x86: Have static function tracing always test for function graph
kprobes: Add IPMODIFY flag to kprobe_ftrace_ops
ftrace, kprobes: Support IPMODIFY flag to find IP modify conflict
kprobes/ftrace: Recover original IP if pre_handler doesn't change it
tracing/trivial: Fix typos and make an int into a bool
tracing: Deletion of an unnecessary check before iput()
...
Merge first patchbomb from Andrew Morton:
- a few minor cifs fixes
- dma-debug upadtes
- ocfs2
- slab
- about half of MM
- procfs
- kernel/exit.c
- panic.c tweaks
- printk upates
- lib/ updates
- checkpatch updates
- fs/binfmt updates
- the drivers/rtc tree
- nilfs
- kmod fixes
- more kernel/exit.c
- various other misc tweaks and fixes
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (190 commits)
exit: pidns: fix/update the comments in zap_pid_ns_processes()
exit: pidns: alloc_pid() leaks pid_namespace if child_reaper is exiting
exit: exit_notify: re-use "dead" list to autoreap current
exit: reparent: call forget_original_parent() under tasklist_lock
exit: reparent: avoid find_new_reaper() if no children
exit: reparent: introduce find_alive_thread()
exit: reparent: introduce find_child_reaper()
exit: reparent: document the ->has_child_subreaper checks
exit: reparent: s/while_each_thread/for_each_thread/ in find_new_reaper()
exit: reparent: fix the cross-namespace PR_SET_CHILD_SUBREAPER reparenting
exit: reparent: fix the dead-parent PR_SET_CHILD_SUBREAPER reparenting
exit: proc: don't try to flush /proc/tgid/task/tgid
exit: release_task: fix the comment about group leader accounting
exit: wait: drop tasklist_lock before psig->c* accounting
exit: wait: don't use zombie->real_parent
exit: wait: cleanup the ptrace_reparented() checks
usermodehelper: kill the kmod_thread_locker logic
usermodehelper: don't use CLONE_VFORK for ____call_usermodehelper()
fs/hfs/catalog.c: fix comparison bug in hfs_cat_keycmp
nilfs2: fix the nilfs_iget() vs. nilfs_new_inode() races
...
Drop the vendor-prefix from the "ti,system-power-controller" device-tree
property name.
It has been agreed to make "system-power-controller" a standard property
and to drop the vendor-prefix that is currently used by several drivers.
Note that drivers that have used "<vendor>,system-power-controller" in a
released kernel will need to support both versions.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Configure the RTC as system-power controller, which allows the system to
be powered off as well as woken up again on subsequent RTC alarms.
Note that the PMIC needs to be put in SLEEP (rather than OFF) mode to
maintain RTC power. Specifically, this means that the PMIC
ti,pmic-shutdown-controller property must be left unset in order to be
able to wake up on RTC alarms.
Tested on BeagleBone Black (rev A5).
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the more common pr_warn.
Coalesce formats, realign arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Coalesce the formats and align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eliminate the unlikely possibility of message interleaving for
early_printk/early_vprintk use.
early_vprintk can be done via the %pV extension so remove this
unnecessary function and change early_printk to have the equivalent
vprintk code.
All uses of early_printk already end with a newline so also remove the
unnecessary newline from the early_printk function.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces calls to get_unused_fd() with equivalent call to
get_unused_fd_flags(0) to preserve current behavor for existing code.
In a further patch, get_unused_fd() will be removed so that new code start
using get_unused_fd_flags(), with the hope O_CLOEXEC could be used, either
by default or choosen by userspace.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces calls to get_unused_fd() with equivalent call to
get_unused_fd_flags(0) to preserve current behavor for existing code.
In a further patch, get_unused_fd() will be removed so that new code start
using get_unused_fd_flags(), with the hope O_CLOEXEC could be used, either
by default or choosen by userspace.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As a small zero page, huge zero page should not be accounted in smaps
report as normal page.
For small pages we rely on vm_normal_page() to filter out zero page, but
vm_normal_page() is not designed to handle pmds. We only get here due
hackish cast pmd to pte in smaps_pte_range() -- pte and pmd format is not
necessary compatible on each and every architecture.
Let's add separate codepath to handle pmds. follow_trans_huge_pmd() will
detect huge zero page for us.
We would need pmd_dirty() helper to do this properly. The patch adds it
to THP-enabled architectures which don't yet have one.
[akpm@linux-foundation.org: use do_div to fix 32-bit build]
Signed-off-by: "Kirill A. Shutemov" <kirill@shutemov.name>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Tested-by: Fengwei Yin <yfw.kernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This off by one bug is harmless but it upsets the static checkers and the
code is obvious so it doesn't hurt to fix it. The Smatch warning is:
arch/sh/mm/numa.c:47 setup_bootmem_node()
error: buffer overflow 'node_data' 1024 <= 1024
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull VFS changes from Al Viro:
"First pile out of several (there _definitely_ will be more). Stuff in
this one:
- unification of d_splice_alias()/d_materialize_unique()
- iov_iter rewrite
- killing a bunch of ->f_path.dentry users (and f_dentry macro).
Getting that completed will make life much simpler for
unionmount/overlayfs, since then we'll be able to limit the places
sensitive to file _dentry_ to reasonably few. Which allows to have
file_inode(file) pointing to inode in a covered layer, with dentry
pointing to (negative) dentry in union one.
Still not complete, but much closer now.
- crapectomy in lustre (dead code removal, mostly)
- "let's make seq_printf return nothing" preparations
- assorted cleanups and fixes
There _definitely_ will be more piles"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
copy_from_iter_nocache()
new helper: iov_iter_kvec()
csum_and_copy_..._iter()
iov_iter.c: handle ITER_KVEC directly
iov_iter.c: convert copy_to_iter() to iterate_and_advance
iov_iter.c: convert copy_from_iter() to iterate_and_advance
iov_iter.c: get rid of bvec_copy_page_{to,from}_iter()
iov_iter.c: convert iov_iter_zero() to iterate_and_advance
iov_iter.c: convert iov_iter_get_pages_alloc() to iterate_all_kinds
iov_iter.c: convert iov_iter_get_pages() to iterate_all_kinds
iov_iter.c: convert iov_iter_npages() to iterate_all_kinds
iov_iter.c: iterate_and_advance
iov_iter.c: macros for iterating over iov_iter
kill f_dentry macro
dcache: fix kmemcheck warning in switch_names
new helper: audit_file()
nfsd_vfs_write(): use file_inode()
ncpfs: use file_inode()
kill f_dentry uses
lockd: get rid of ->f_path.dentry->d_sb
...
Pull x86 microcode loading updates from Ingo Molnar:
"The main changes in this cycle are:
- Reload microcode when resuming and the case when only the early
loader has been utilized. (Borislav Petkov)
- Also, do not load the driver on paravirt guests. (Boris
Ostrovsky)"
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode/intel: Fish out the stashed microcode for the BSP
x86, microcode: Reload microcode on resume
x86, microcode: Don't initialize microcode code on paravirt
x86, microcode, intel: Drop unused parameter
x86, microcode, AMD: Do not use smp_processor_id() in preemtible context
Pull x86 vdso updates from Ingo Molnar:
"Various vDSO updates from Andy Lutomirski, mostly cleanups and
reorganization to improve maintainability, but also some
micro-optimizations and robustization changes"
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86_64/vsyscall: Restore orig_ax after vsyscall seccomp
x86_64: Add a comment explaining the TASK_SIZE_MAX guard page
x86_64,vsyscall: Make vsyscall emulation configurable
x86_64, vsyscall: Rewrite comment and clean up headers in vsyscall code
x86_64, vsyscall: Turn vsyscalls all the way off when vsyscall==none
x86,vdso: Use LSL unconditionally for vgetcpu
x86: vdso: Fix build with older gcc
x86_64/vdso: Clean up vgetcpu init and merge the vdso initcalls
x86_64/vdso: Remove jiffies from the vvar page
x86/vdso: Make the PER_CPU segment 32 bits
x86/vdso: Make the PER_CPU segment start out accessed
x86/vdso: Change the PER_CPU segment to use struct desc_struct
x86_64/vdso: Move getcpu code from vsyscall_64.c to vdso/vma.c
x86_64/vsyscall: Move all of the gate_area code to vsyscall_64.c
Pull x86 RAS update from Ingo Molnar:
"The biggest change in this cycle is better support for UCNA
(UnCorrected No Action) events:
"Handle all uncorrected error reports in the same way (soft
offline the page). We used to only do that for SRAO
(software recoverable action optional) machine checks, but
it makes sense to also do it for UCNA (UnCorrected No
Action) logs found by CMCI or polling."
plus various x86 MCE handling updates and fixes"
* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Spell "panicked" correctly
x86, mce: Support memory error recovery for both UCNA and Deferred error in machine_check_poll
x86, mce, severity: Extend the the mce_severity mechanism to handle UCNA/DEFERRED error
x86, MCE, AMD: Assign interrupt handler only when bank supports it
x86, MCE, AMD: Drop software-defined bank in error thresholding
x86, MCE, AMD: Move invariant code out from loop body
x86, MCE, AMD: Correct thresholding error logging
x86, MCE, AMD: Use macros to compute bank MSRs
RAS, HWPOISON: Fix wrong error recovery status
GHES: Make ghes_estatus_caches static
APEI, GHES: Cleanup unnecessary function for lockless list
Pull x86 mm tree changes from Ingo Molnar:
"The biggest change is full PAT support from Jürgen Gross:
The x86 architecture offers via the PAT (Page Attribute Table) a
way to specify different caching modes in page table entries. The
PAT MSR contains 8 entries each specifying one of 6 possible cache
modes. A pte references one of those entries via 3 bits:
_PAGE_PAT, _PAGE_PWT and _PAGE_PCD.
The Linux kernel currently supports only 4 different cache modes.
The PAT MSR is set up in a way that the setting of _PAGE_PAT in a
pte doesn't matter: the top 4 entries in the PAT MSR are the same
as the 4 lower entries.
This results in the kernel not supporting e.g. write-through mode.
Especially this cache mode would speed up drivers of video cards
which now have to use uncached accesses.
OTOH some old processors (Pentium) don't support PAT correctly and
the Xen hypervisor has been using a different PAT MSR configuration
for some time now and can't change that as this setting is part of
the ABI.
This patch set abstracts the cache mode from the pte and introduces
tables to translate between cache mode and pte bits (the default
cache mode "write back" is hard-wired to PAT entry 0). The tables
are statically initialized with values being compatible to old
processors and current usage. As soon as the PAT MSR is changed
(or - in case of Xen - is read at boot time) the tables are changed
accordingly. Requests of mappings with special cache modes are
always possible now, in case they are not supported there will be a
fallback to a compatible but slower mode.
Summing it up, this patch set adds the following features:
- capability to support WT and WP cache modes on processors with
full PAT support
- processors with no or uncorrect PAT support are still working as
today, even if WT or WP cache mode are selected by drivers for
some pages
- reduction of Xen special handling regarding cache mode
Another change is a boot speedup on ridiculously large RAM systems,
plus other smaller fixes"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
x86: mm: Move PAT only functions to mm/pat.c
xen: Support Xen pv-domains using PAT
x86: Enable PAT to use cache mode translation tables
x86: Respect PAT bit when copying pte values between large and normal pages
x86: Support PAT bit in pagetable dump for lower levels
x86: Clean up pgtable_types.h
x86: Use new cache mode type in memtype related functions
x86: Use new cache mode type in mm/ioremap.c
x86: Use new cache mode type in setting page attributes
x86: Remove looking for setting of _PAGE_PAT_LARGE in pageattr.c
x86: Use new cache mode type in track_pfn_remap() and track_pfn_insert()
x86: Use new cache mode type in mm/iomap_32.c
x86: Use new cache mode type in asm/pgtable.h
x86: Use new cache mode type in arch/x86/mm/init_64.c
x86: Use new cache mode type in arch/x86/pci
x86: Use new cache mode type in drivers/video/fbdev/vermilion
x86: Use new cache mode type in drivers/video/fbdev/gbefb.c
x86: Use new cache mode type in include/asm/fb.h
x86: Make page cache mode a real type
x86: mm: Use 2GB memory block size on large-memory x86-64 systems
...
Pull x86 platform changes from Ingo Molnar:
"A handful of numachip APIC driver updates/fixes, and two small SGI/UV
fixes"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: numachip: APIC driver cleanups
x86: numachip: Elide self-IPI ICR polling
x86: numachip: Fix 16-bit APIC ID truncation
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: UV BAU: Increase maximum CPUs per socket/hub
x86: UV BAU: Avoid NULL pointer reference in ptc_seq_show
Pull EFI updates from Ingo Molnar:
"Changes in this cycle are:
- support module unload for efivarfs (Mathias Krause)
- another attempt at moving x86 to libstub taking advantage of the
__pure attribute (Ard Biesheuvel)
- add EFI runtime services section to ptdump (Mathias Krause)"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, ptdump: Add section for EFI runtime services
efi/x86: Move x86 back to libstub
efivarfs: Allow unloading when build as module
Pull x86 build, cleanup and defconfig updates from Ingo Molnar:
"A single minor build change to suppress a repetitive build messages,
misc cleanups and a defconfig update"
* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/purgatory, build: Suppress kexec-purgatory.c is up to date message
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, CPU, AMD: Move K8 TLB flush filter workaround to K8 code
x86, espfix: Remove stale ptemask
x86, msr: Use seek definitions instead of hard-coded values
x86, msr: Convert printk to pr_foo()
x86, msr: Use PTR_ERR_OR_ZERO
x86/simplefb: Use PTR_ERR_OR_ZERO
x86/sysfb: Use PTR_ERR_OR_ZERO
x86, cpuid: Use PTR_ERR_OR_ZERO
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kconfig/defconfig: Enable CONFIG_FHANDLE=y
Pull x86 boot and percpu updates from Ingo Molnar:
"This tree contains a bootable images documentation update plus three
slightly misplaced x86/asm percpu changes/optimizations"
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64: Use RIP-relative addressing for most per-CPU accesses
x86-64: Handle PC-relative relocations on per-CPU data
x86: Convert a few more per-CPU items to read-mostly ones
x86, boot: Document intermediates more clearly
Pull x86 MPX support from Thomas Gleixner:
"This enables support for x86 MPX.
MPX is a new debug feature for bound checking in user space. It
requires kernel support to handle the bound tables and decode the
bound violating instruction in the trap handler"
* 'x86-mpx-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
asm-generic: Remove asm-generic arch_bprm_mm_init()
mm: Make arch_unmap()/bprm_mm_init() available to all architectures
x86: Cleanly separate use of asm-generic/mm_hooks.h
x86 mpx: Change return type of get_reg_offset()
fs: Do not include mpx.h in exec.c
x86, mpx: Add documentation on Intel MPX
x86, mpx: Cleanup unused bound tables
x86, mpx: On-demand kernel allocation of bounds tables
x86, mpx: Decode MPX instruction to get bound violation information
x86, mpx: Add MPX-specific mmap interface
x86, mpx: Introduce VM_MPX to indicate that a VMA is MPX specific
x86, mpx: Add MPX to disabled features
ia64: Sync struct siginfo with general version
mips: Sync struct siginfo with general version
mpx: Extend siginfo structure to include bound violation information
x86, mpx: Rename cfg_reg_u and status_reg
x86: mpx: Give bndX registers actual names
x86: Remove arbitrary instruction size limit in instruction decoder
Pull irq domain updates from Thomas Gleixner:
"The real interesting irq updates:
- Support for hierarchical irq domains:
For complex interrupt routing scenarios where more than one
interrupt related chip is involved we had no proper representation
in the generic interrupt infrastructure so far. That made people
implement rather ugly constructs in their nested irq chip
implementations. The main offenders are x86 and arm/gic.
To distangle that mess we have now hierarchical irqdomains which
seperate the various interrupt chips and connect them via the
hierarchical domains. That keeps the domain specific details
internal to the particular hierarchy level and removes the
criss/cross referencing of chip internals. The resulting hierarchy
for a complex x86 system will look like this:
vector mapped: 74
msi-0 mapped: 2
dmar-ir-1 mapped: 69
ioapic-1 mapped: 4
ioapic-0 mapped: 20
pci-msi-2 mapped: 45
dmar-ir-0 mapped: 3
ioapic-2 mapped: 1
pci-msi-1 mapped: 2
htirq mapped: 0
Neither ioapic nor pci-msi know about the dmar interrupt remapping
between themself and the vector domain. If interrupt remapping is
disabled ioapic and pci-msi become direct childs of the vector
domain.
In hindsight we should have done that years ago, but in hindsight
we always know better :)
- Support for generic MSI interrupt domain handling
We have more and more non PCI related MSI interrupts, so providing
a generic infrastructure for this is better than having all
affected architectures implementing their own private hacks.
- Support for PCI-MSI interrupt domain handling, based on the generic
MSI support.
This part carries the pci/msi branch from Bjorn Helgaas pci tree to
avoid a massive conflict. The PCI/MSI parts are acked by Bjorn.
I have two more branches on top of this. The full conversion of x86
to hierarchical domains and a partial conversion of arm/gic"
* 'irq-irqdomain-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
genirq: Move irq_chip_write_msi_msg() helper to core
PCI/MSI: Allow an msi_controller to be associated to an irq domain
PCI/MSI: Provide mechanism to alloc/free MSI/MSIX interrupt from irqdomain
PCI/MSI: Enhance core to support hierarchy irqdomain
PCI/MSI: Move cached entry functions to irq core
genirq: Provide default callbacks for msi_domain_ops
genirq: Introduce msi_domain_alloc/free_irqs()
asm-generic: Add msi.h
genirq: Add generic msi irq domain support
genirq: Introduce callback irq_chip.irq_write_msi_msg
genirq: Work around __irq_set_handler vs stacked domains ordering issues
irqdomain: Introduce helper function irq_domain_add_hierarchy()
irqdomain: Implement a method to automatically call parent domains alloc/free
genirq: Introduce helper irq_domain_set_info() to reduce duplicated code
genirq: Split out flow handler typedefs into seperate header file
genirq: Add IRQ_SET_MASK_OK_DONE to support stacked irqchip
genirq: Introduce irq_chip.irq_compose_msi_msg() to support stacked irqchip
genirq: Add more helper functions to support stacked irq_chip
genirq: Introduce helper functions to support stacked irq_chip
irqdomain: Do irq_find_mapping and set_type for hierarchy irqdomain in case OF
...
Pull irq core updates from Thomas Gleixner:
"This is the first (boring) part of irq updates:
- support for big endian I/O accessors in the generic irq chip
- cleanup of brcmstb/bcm7120 drivers so they can be reused for non
ARM SoCs
- the usual pile of fixes and updates for the various ARM irq chips"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
irqchip: dw-apb-ictl: Add PM support
irqchip: dw-apb-ictl: Enable IRQ_GC_MASK_CACHE_PER_TYPE
irqchip: dw-apb-ictl: Always use use {readl|writel}_relaxed
ARM: orion: convert the irq_reg_{readl,writel} calls to the new API
irqchip: atmel-aic: Add missing entry for rm9200 irq fixups
irqchip: atmel-aic: Rename at91sam9_aic_irq_fixup for naming consistency
irqchip: atmel-aic: Add specific irq fixup function for sam9g45 and sam9rl
irqchip: atmel-aic: Add irq fixups for at91sam926x SoCs
irqchip: atmel-aic: Add irq fixup for RTT block
irqchip: brcmstb-l2: Convert driver to use irq_reg_{readl,writel}
irqchip: bcm7120-l2: Convert driver to use irq_reg_{readl,writel}
irqchip: bcm7120-l2: Decouple driver from brcmstb-l2
irqchip: bcm7120-l2: Extend driver to support 64+ bit controllers
irqchip: bcm7120-l2: Use gc->mask_cache to simplify suspend/resume functions
irqchip: bcm7120-l2: Fix missing nibble in gc->unused mask
irqchip: bcm7120-l2: Make sure all register accesses use base+offset
irqchip: bcm7120-l2, brcmstb-l2: Remove ARM Kconfig dependency
irqchip: bcm7120-l2: Eliminate bad IRQ check
irqchip: brcmstb-l2: Eliminate dependency on ARM code
genirq: Generic chip: Add big endian I/O accessors
...
I'm such a moron! The simple solution of saving the BSP patch
for use on resume was too simple (and wrong!), hint:
sizeof(struct microcode_intel).
What needs to be done instead is to fish out the microcode patch
we have stashed previously and apply that on the BSP in case the
late loader hasn't been utilized.
So do that instead.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20141208110820.GB20057@pd.tnic
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle are:
- 'Nested Sleep Debugging', activated when CONFIG_DEBUG_ATOMIC_SLEEP=y.
This instruments might_sleep() checks to catch places that nest
blocking primitives - such as mutex usage in a wait loop. Such
bugs can result in hard to debug races/hangs.
Another category of invalid nesting that this facility will detect
is the calling of blocking functions from within schedule() ->
sched_submit_work() -> blk_schedule_flush_plug().
There's some potential for false positives (if secondary blocking
primitives themselves are not ready yet for this facility), but the
kernel will warn once about such bugs per bootup, so the warning
isn't much of a nuisance.
This feature comes with a number of fixes, for problems uncovered
with it, so no messages are expected normally.
- Another round of sched/numa optimizations and refinements, for
CONFIG_NUMA_BALANCING=y.
- Another round of sched/dl fixes and refinements.
Plus various smaller fixes and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
sched: Add missing rcu protection to wake_up_all_idle_cpus
sched/deadline: Introduce start_hrtick_dl() for !CONFIG_SCHED_HRTICK
sched/numa: Init numa balancing fields of init_task
sched/deadline: Remove unnecessary definitions in cpudeadline.h
sched/cpupri: Remove unnecessary definitions in cpupri.h
sched/deadline: Fix rq->dl.pushable_tasks bug in push_dl_task()
sched/fair: Fix stale overloaded status in the busiest group finding logic
sched: Move p->nr_cpus_allowed check to select_task_rq()
sched/completion: Document when to use wait_for_completion_io_*()
sched: Update comments about CLONE_NEWUTS and CLONE_NEWIPC
sched/fair: Kill task_struct::numa_entry and numa_group::task_list
sched: Refactor task_struct to use numa_faults instead of numa_* pointers
sched/deadline: Don't check CONFIG_SMP in switched_from_dl()
sched/deadline: Reschedule from switched_from_dl() after a successful pull
sched/deadline: Push task away if the deadline is equal to curr during wakeup
sched/deadline: Add deadline rq status print
sched/deadline: Fix artificial overrun introduced by yield_task_dl()
sched/rt: Clean up check_preempt_equal_prio()
sched/core: Use dl_bw_of() under rcu_read_lock_sched()
sched: Check if we got a shallowest_idle_cpu before searching for least_loaded_cpu
...
Pull leftover perf fixes from Ingo Molnar:
"Two perf fixes left over from the previous cycle"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf session: Do not fail on processing out of order event
x86/asm/traps: Disable tracing and kprobes in fixup_bad_iret and sync_regs
Pull perf events update from Ingo Molnar:
"On the kernel side there's few changes, the one that stands out is
PEBS machine state sampling support on x86, by Stephane Eranian.
On the tooling side:
User visible tooling changes:
- Don't open the DWARF info multiple times, keeping instead a dwfl
handle in struct dso, greatly speeding up 'perf report' on powerpc.
(Sukadev Bhattiprolu)
- Introduce PARSE_OPT_DISABLED option flag and use it to avoid
showing undersired options in tools that provides frontends to
'perf record', like sched, kvm, etc (Namhyung Kim)
- Fallback to kallsyms when using the minimal 'ELF' loader (Arnaldo
Carvalho de Melo)
- Fix annotation with kcore (Adrian Hunter)
- Support source line numbers in annotate using a hotkey (Andi Kleen)
- Callchain improvements including:
* Enable printing the srcline in the history
* Make get_srcline fall back to sym+offset (Andi Kleen)
- TUI hist_entry browser fixes, including showing missing overhead
value for first level callchain. Detected comparing the output of
--stdio/--gui (that matched) with --tui, that had this problem.
(Namhyung Kim)
- Support handling complete branch stacks as histograms (Andi Kleen)
Tooling infrastructure changes:
- Prep work for supporting per-pkg and snapshot counters in 'perf
stat' (Jiri Olsa)
- 'perf stat' refactorings, moving stuff from it to evsel.c to use in
per-pkg/snapshot format changes (Jiri Olsa)
- Add per-pkg format file parsing (Matt Fleming)
- Clean up libelf feature support code (Namhyung Kim)
- Add gzip decompression support for kernel modules (Namhyung Kim)
- More prep patches for Intel PT, including a a thread stack and more
stuff made available via the database export mechanism (Adrian
Hunter)
- More Intel PT work, including a facility to export sample data
(comms, threads, symbol names, etc) in a database friendly way,
with an script to use this to create a postgresql database.
(Adrian Hunter)
- Make sure that thread->mg->machine points to the machine where the
thread exists (it was being set only for the kmaps kernel modules
case, do it as well for the mmaps) and use it to shorten function
signatures (Arnaldo Carvalho de Melo)
... and lots of other fixes and smaller improvements"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (91 commits)
perf report: In branch stack mode use address history sorting
perf report: Add --branch-history option
perf callchain: Support handling complete branch stacks as histograms
perf stat: Add support for snapshot counters
perf stat: Add support for per-pkg counters
perf tools: Remove perf_evsel__read interface
perf stat: Use read_counter in read_counter_aggr
perf stat: Make read_counter work over the thread dimension
perf stat: Use perf_evsel__read_cb in read_counter
perf tools: Add snapshot format file parsing
perf tools: Add per-pkg format file parsing
perf evsel: Introduce perf_evsel__read_cb function
perf evsel: Introduce perf_counts_values__scale function
perf evsel: Introduce perf_evsel__compute_deltas function
perf tools: Allow to force redirect pr_debug to stderr.
perf tools: Fix segfault due to invalid kernel dso access
perf callchain: Make get_srcline fall back to sym+offset
perf symbols: Move bfd_demangle stubbing to its only user
perf callchain: Enable printing the srcline in the history
perf tools: Collapse first level callchain entry if it has sibling
...
Pull locking tree changes from Ingo Molnar:
"Two changes: a documentation update and a ticket locks live lock fix"
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ticketlock: Fix spin_unlock_wait() livelock
locking/lglocks: Add documentation of current lglocks implementation
While there normally is no reason to have a pull request for asm-generic
but have all changes get merged through whichever tree needs them, I do
have a series for 3.19. There are two sets of patches that change
significant portions of asm/io.h, and this branch contains both in order
to resolve the conflicts:
- Will Deacon has done a set of patches to ensure that all architectures
define {read,write}{b,w,l,q}_relaxed() functions or get them by
including asm-generic/io.h. These functions are commonly used on ARM
specific drivers to avoid expensive L2 cache synchronization implied by
the normal {read,write}{b,w,l,q}, but we need to define them on all
architectures in order to share the drivers across architectures and
to enable CONFIG_COMPILE_TEST configurations for them
- Thierry Reding has done an unrelated set of patches that extends
the asm-generic/io.h file to the degree necessary to make it useful
on ARM64 and potentially other architectures.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xUv6
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic asm/io.h rewrite from Arnd Bergmann:
"While there normally is no reason to have a pull request for
asm-generic but have all changes get merged through whichever tree
needs them, I do have a series for 3.19.
There are two sets of patches that change significant portions of
asm/io.h, and this branch contains both in order to resolve the
conflicts:
- Will Deacon has done a set of patches to ensure that all
architectures define {read,write}{b,w,l,q}_relaxed() functions or
get them by including asm-generic/io.h.
These functions are commonly used on ARM specific drivers to avoid
expensive L2 cache synchronization implied by the normal
{read,write}{b,w,l,q}, but we need to define them on all
architectures in order to share the drivers across architectures
and to enable CONFIG_COMPILE_TEST configurations for them
- Thierry Reding has done an unrelated set of patches that extends
the asm-generic/io.h file to the degree necessary to make it useful
on ARM64 and potentially other architectures"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (29 commits)
ARM64: use GENERIC_PCI_IOMAP
sparc: io: remove duplicate relaxed accessors on sparc32
ARM: sa11x0: Use void __iomem * in MMIO accessors
arm64: Use include/asm-generic/io.h
ARM: Use include/asm-generic/io.h
asm-generic/io.h: Implement generic {read,write}s*()
asm-generic/io.h: Reconcile I/O accessor overrides
/dev/mem: Use more consistent data types
Change xlate_dev_{kmem,mem}_ptr() prototypes
ARM: ixp4xx: Properly override I/O accessors
ARM: ixp4xx: Fix build with IXP4XX_INDIRECT_PCI
ARM: ebsa110: Properly override I/O accessors
ARC: Remove redundant PCI_IOBASE declaration
documentation: memory-barriers: clarify relaxed io accessor semantics
x86: io: implement dummy relaxed accessor macros for writes
tile: io: implement dummy relaxed accessor macros for writes
sparc: io: implement dummy relaxed accessor macros for writes
powerpc: io: implement dummy relaxed accessor macros for writes
parisc: io: implement dummy relaxed accessor macros for writes
mn10300: io: implement dummy relaxed accessor macros for writes
...
This adds support for two new ARM64 platforms:
* ARM Juno
* AMD Seattle
We had submissions for a number of additional platforms
from Samsung, Freescale and Spreadtrum but are still working
out the best process for getting these merged.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yqur
-----END PGP SIGNATURE-----
Merge tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM64 SoC changes from Arnd Bergmann:
"This adds support for two new ARM64 platforms:
- ARM Juno
- AMD Seattle
We had submissions for a number of additional platforms from Samsung,
Freescale and Spreadtrum but are still working out the best process
for getting these merged"
* tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: amd-seattle: Fix PCI bus range due to SMMU limitation
arm64: ARM: Fix the Generic Timers interrupt active level description
arm64: amd-seattle: Adding device tree for AMD Seattle platform
arm64: Add Juno board device tree.
arm64: Create link to include/dt-bindings to enable C preprocessor use.
This is a collection of the various changes to defconfig files,
most importantly enabling some additional platforms in the
multi_v7_defconfig file. These are split out into a separate
branch to avoid most of the merge conflicts in the defconfig
files.
This also touches 12 other defconfig files for shmobile,
at91, hisilicon, keystone, mvebu, omap, and tegra.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=brXv
-----END PGP SIGNATURE-----
Merge tag 'defconfig-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig changes from Arnd Bergmann:
"This is a collection of the various changes to defconfig files, most
importantly enabling some additional platforms in the
multi_v7_defconfig file. These are split out into a separate branch
to avoid most of the merge conflicts in the defconfig files.
This also touches 12 other defconfig files for shmobile, at91,
hisilicon, keystone, mvebu, omap, and tegra"
* tag 'defconfig-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
ARM: omap2plus_defconfig: enable ECAP and EHRPWM
ARM: omap2plus_defconfig: enable XHCI
ARM: omap2plus_defconfig: enable AM33XX SoC sound
ARM: omap2plus_defconfig: enable EDT FT5X06 touchscreen
ARM: omap2plus_defconfig: remove unwanted ethernet drivers
ARM: multi_v7_defconfig: enable MAX77686 PMIC drivers for exynos4412-prime based SoCs
ARM: at91/defconfig: add DM9000 to at91_dt
ARM: at91/defconfig: add QT1070 to at91_dt
ARM: at91/defconfig: add TCB PWM driver selection
ARM: at91/defconfig: add the XDMA driver
ARM: at91: sama5: update defconfig
ARM: defconfig: imx_v6_v7_defconfig updates
ARM: multi_v7_defconfig: add driver support for hix5hd2
ARM: exynos_defconfig: Use 16 minors per MMC block device
ARM: mvebu: add MTD_BLOCK to mvebu_v7_defconfig
ARM: mvebu: enable i2c device in mvebu_v7_defconfig
ARM: mvebu: re-enable SDHCI driver for Armada 38x SoC in v7 defconfig
ARM: tegra: Regenerate default configuration
ARM: multi_v7_defconfig: Enable cgroups
ARM: multi_v7_defconfig: Enable Broadcom Cygnus
...
The GPMC driver has traditionally been considered a part of the
OMAP platform code and tightly interweaved with some of the boards.
With this cleanup, it has finally come to the point where it makes
sense to move it out of arch/arm into drivers/memory, where we already
have other drivers for similar hardware. The cleanups are still
ongoing, with the goal of eventually having a standalone driver
that does not require an interface to architecture code.
This is a separate branch because of dependencies on multiple other
branches, and to keep the drivers changes separate from the normal
cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=U4Fz
-----END PGP SIGNATURE-----
Merge tag 'omap-gpmc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC/OMAP GPMC driver cleanup and move from Arnd Bergmann:
"The GPMC driver has traditionally been considered a part of the OMAP
platform code and tightly interweaved with some of the boards.
With this cleanup, it has finally come to the point where it makes
sense to move it out of arch/arm into drivers/memory, where we already
have other drivers for similar hardware. The cleanups are still
ongoing, with the goal of eventually having a standalone driver that
does not require an interface to architecture code.
This is a separate branch because of dependencies on multiple other
branches, and to keep the drivers changes separate from the normal
cleanups"
* tag 'omap-gpmc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
memory: gpmc: Move omap gpmc code to live under drivers
ARM: OMAP2+: Move GPMC initcall to devices.c
ARM: OMAP2+: Prepare to move GPMC to drivers by platform data header
ARM: OMAP2+: Remove unnecesary include in GPMC driver
ARM: OMAP2+: Drop board file for 3430sdp
ARM: OMAP2+: Drop board file for ti8168evm
ARM: OMAP2+: Drop legacy code for gpmc-smc91x.c
ARM: OMAP2+: Require proper GPMC timings for devices
ARM: OMAP2+: Show bootloader GPMC timings to allow configuring the .dts file
ARM: OMAP2+: Fix support for multiple devices on a GPMC chip select
ARM: OMAP2+: gpmc: Sanity check GPMC fck on probe
ARM: OMAP2+: gpmc: Keep Chip Select disabled while configuring it
ARM: OMAP2+: gpmc: Always enable A26-A11 for non NAND devices
ARM: OMAP2+: gpmc: Error out if timings fail in gpmc_probe_generic_child()
ARM: OMAP2+: gpmc: Print error message in set_gpmc_timing_reg()
The DT branch adds a lot of new stuff for additional SoC and board
support. The branch is the largest one and contains 513 out of the
total 972 non-merge arm-soc changesets for 3.19.
Most of the changes are about enabling additional on-chip devices for
existing machines, but there are also an unusual number of new SoC
types being added this time:
* AMLogic Meson8
* ARM Realview in DT mode
* Allwinner A80
* Broadcom BCM47081
* Broadcom Cygnus
* Freescale LS1021A
* Freescale Vybrid 500 series
* Mediatek MT6592, MT8127, MT8135
* STMicroelectronics STiH410
* Samsung Exynos4415
The level of support for the above differs widely, some are just
stubs with nothing more than CPU, memory and a UART, but others
are fairly complete. As usual, these get extended over time.
There are also many new boards getting added, this is the
list of model strings that are showing up in new dts files:
* ARM RealView PB1176
* Altera SOCFPGA Arria 10
* Asus RT-N18U (BCM47081)
* Buffalo WZR-1750DHP (BCM4708)
* Buffalo WZR-600DHP2 (BCM47081)
* Cygnus Enterprise Phone (BCM911360_ENTPHN)
* D-Link DIR-665
* Google Spring
* IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
* IGEPv2 Rev. F (TI OMAP AM/DM37x)
* LS1021A QDS Board
* LS1021A TWR Board
* LeMaker Banana Pi
* MarsBoard RK3066
* MediaTek MT8127 Moose Board
* MediaTek MT8135 evaluation board
* Mele M3
* Merrii A80 Optimus Board
* Netgear R6300 V2 (BCM4708)
* Nomadik STN8815NHK
* NovaTech OrionLXm
* Olimex A20-OLinuXino-LIME2
* Raspberry Pi Model B+
* STiH410 B2120
* Samsung Monk board
* Samsung Rinato board
* Synology DS213j
* Synology DS414
* TBS2910 Matrix ARM mini PC
* TI AM5728 BeagleBoard-X15
* Toradex Colibri VF50 on Colibri Evaluation Board
* Zynq ZYBO Development Board
Other notable changes include:
* exynos: cleanup of existing dts files
* mvebu: improved pinctrl support for Armada 370/XP
* nomadik: restructuring dts files
* omap: added CAN bus support
* shmobile: added clock support for some SoCs
* shmobile: added sound support for some SoCs
* sirf: reset controller support
* sunxi: continuing the relicensing under dual GPL/MIT
* sunxi: lots of new on-chip device support
* sunxi: working simplefb support (long awaited)
* various: provide stdout-path property for earlycon
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BHwA
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Arnd Bergmann:
"The DT branch adds a lot of new stuff for additional SoC and board
support. The branch is the largest one and contains 513 out of the
total 972 non-merge arm-soc changesets for 3.19.
Most of the changes are about enabling additional on-chip devices for
existing machines, but there are also an unusual number of new SoC
types being added this time:
- AMLogic Meson8
- ARM Realview in DT mode
- Allwinner A80
- Broadcom BCM47081
- Broadcom Cygnus
- Freescale LS1021A
- Freescale Vybrid 500 series
- Mediatek MT6592, MT8127, MT8135
- STMicroelectronics STiH410
- Samsung Exynos4415
The level of support for the above differs widely, some are just stubs
with nothing more than CPU, memory and a UART, but others are fairly
complete. As usual, these get extended over time.
There are also many new boards getting added, this is the list of
model strings that are showing up in new dts files:
- ARM RealView PB1176
- Altera SOCFPGA Arria 10
- Asus RT-N18U (BCM47081)
- Buffalo WZR-1750DHP (BCM4708)
- Buffalo WZR-600DHP2 (BCM47081)
- Cygnus Enterprise Phone (BCM911360_ENTPHN)
- D-Link DIR-665
- Google Spring
- IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
- IGEPv2 Rev. F (TI OMAP AM/DM37x)
- LS1021A QDS Board
- LS1021A TWR Board
- LeMaker Banana Pi
- MarsBoard RK3066
- MediaTek MT8127 Moose Board
- MediaTek MT8135 evaluation board
- Mele M3
- Merrii A80 Optimus Board
- Netgear R6300 V2 (BCM4708)
- Nomadik STN8815NHK
- NovaTech OrionLXm
- Olimex A20-OLinuXino-LIME2
- Raspberry Pi Model B+
- STiH410 B2120
- Samsung Monk board
- Samsung Rinato board
- Synology DS213j
- Synology DS414
- TBS2910 Matrix ARM mini PC
- TI AM5728 BeagleBoard-X15
- Toradex Colibri VF50 on Colibri Evaluation Board
- Zynq ZYBO Development Board
Other notable changes include:
- exynos: cleanup of existing dts files
- mvebu: improved pinctrl support for Armada 370/XP
- nomadik: restructuring dts files
- omap: added CAN bus support
- shmobile: added clock support for some SoCs
- shmobile: added sound support for some SoCs
- sirf: reset controller support
- sunxi: continuing the relicensing under dual GPL/MIT
- sunxi: lots of new on-chip device support
- sunxi: working simplefb support (long awaited)
- various: provide stdout-path property for earlycon"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (510 commits)
ARM: dts: rk3288: add arm,cpu-registers-not-fw-configured
Revert "ARM: dts: rockchip: temporarily disable smp on rk3288"
ARM: BCM5301X: Add DT for Buffalo WZR-600DHP2
ARM: BCM5301X: Add DT for Asus RT-N18U
ARM: BCM5301X: Add DT for Buffalo WZR-1750DHP
ARM: BCM5301X: Add DT for Netgear R6300 V2
ARM: BCM5301X: Add buttons for Netgear R6250
ARM: dts: rockchip: Add input voltage supply regulators in pmic for Marsboard
ARM: BCM5301X: Add IRQs to Broadcom's bus-axi in DTS file
arm: dts: zynq: Add Digilent ZYBO board
arm: dts: zynq: Move crystal freq. to board level
doc: dt: vendor-prefixes: Add Digilent Inc
Documentation: devicetree: Fix Xilinx VDMA specification
ARM: dts: rockchip: set FIFO size for SDMMC, SDIO and EMMC on rk3066 and rk3188
ARM: dts: rockchip: add label property for leds on Radxa Rock
ARM: BCM5301X: Add LEDs for Netgear R6250 V1
ARM: BCM5301X: Add Broadcom's bus-axi to the DTS file
ARM: dts: add sysreg phandle to i2c device nodes for exynos
ARM: dts: Remove unused bootargs from exynos3250-rinato
ARM: dts: add board dts file for Exynos3250-based Monk board
...
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
The largest single change here this time around is the Tegra
iommu/memory controller driver, which gets updated to the new
iommu DT binding. More drivers like this are likely to follow
for the following merge window, but we should be able to do
those through the iommu maintainer.
Other notable changes are:
* reset controller drivers from the reset maintainer (socfpga, sti, berlin)
* fixes for the keystone navigator driver merged last time
* at91 rtc driver changes related to the at91 cleanups
* ARM perf driver changes from Will Deacon
* updates for the brcmstb_gisb driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=MwMG
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
The largest single change here this time around is the Tegra
iommu/memory controller driver, which gets updated to the new iommu DT
binding. More drivers like this are likely to follow for the
following merge window, but we should be able to do those through the
iommu maintainer.
Other notable changes are:
- reset controller drivers from the reset maintainer (socfpga, sti,
berlin)
- fixes for the keystone navigator driver merged last time
- at91 rtc driver changes related to the at91 cleanups
- ARM perf driver changes from Will Deacon
- updates for the brcmstb_gisb driver"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
clocksource: arch_timer: Allow the device tree to specify uninitialized timer registers
clocksource: arch_timer: Fix code to use physical timers when requested
memory: Add NVIDIA Tegra memory controller support
bus: brcmstb_gisb: Add register offset tables for older chips
bus: brcmstb_gisb: Look up register offsets in a table
bus: brcmstb_gisb: Introduce wrapper functions for MMIO accesses
bus: brcmstb_gisb: Make the driver buildable on MIPS
of: Add NVIDIA Tegra memory controller binding
ARM: tegra: Move AHB Kconfig to drivers/amba
amba: Add Kconfig file
clk: tegra: Implement memory-controller clock
serial: samsung: Fix serial config dependencies for exynos7
bus: brcmstb_gisb: resolve section mismatch
ARM: common: edma: edma_pm_resume may be unused
ARM: common: edma: add suspend resume hook
powerpc/iommu: Rename iommu_[un]map_sg functions
rtc: at91sam9: add DT bindings documentation
rtc: at91sam9: use clk API instead of relying on AT91_SLOW_CLOCK
ARM: at91: add clk_lookup entry for RTT devices
rtc: at91sam9: rework the Kconfig description
...
New and updated SoC support, notable changes include:
* bcm: brcmstb SMP support
* bcm: initial iproc/cygnus support
* exynos: Exynos4415 SoC support
* exynos: PMU and suspend support for Exynos5420
* exynos: PMU support for Exynos3250
* exynos: pm related maintenance
* imx: new LS1021A SoC support
* imx: vybrid 610 global timer support
* integrator: convert to using multiplatform configuration
* mediatek: earlyprintk support for mt8127/mt8135
* meson: meson8 soc and l2 cache controller support
* mvebu: Armada 38x CPU hotplug support
* mvebu: drop support for prerelease Armada 375 Z1 stepping
* mvebu: extended suspend support, now works on Armada 370/XP
* omap: hwmod related maintenance
* omap: prcm cleanup
* pxa: initial pxa27x DT handling
* rockchip: SMP support for rk3288
* rockchip: add cpu frequency scaling support
* shmobile: r8a7740 power domain support
* shmobile: various small restart, timer, pci apmu changes
* sunxi: Allwinner A80 (sun9i) earlyprintk support
* ux500: power domain support
Overall, a significant chunk of changes, coming mostly from
the usual suspects: omap, shmobile, samsung and mvebu, all of
which already contain a lot of platform specific code in
arch/arm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lFoH
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Arnd Bergmann:
"New and updated SoC support, notable changes include:
- bcm:
brcmstb SMP support
initial iproc/cygnus support
- exynos:
Exynos4415 SoC support
PMU and suspend support for Exynos5420
PMU support for Exynos3250
pm related maintenance
- imx:
new LS1021A SoC support
vybrid 610 global timer support
- integrator:
convert to using multiplatform configuration
- mediatek:
earlyprintk support for mt8127/mt8135
- meson:
meson8 soc and l2 cache controller support
- mvebu:
Armada 38x CPU hotplug support
drop support for prerelease Armada 375 Z1 stepping
extended suspend support, now works on Armada 370/XP
- omap:
hwmod related maintenance
prcm cleanup
- pxa:
initial pxa27x DT handling
- rockchip:
SMP support for rk3288
add cpu frequency scaling support
- shmobile:
r8a7740 power domain support
various small restart, timer, pci apmu changes
- sunxi:
Allwinner A80 (sun9i) earlyprintk support
- ux500:
power domain support
Overall, a significant chunk of changes, coming mostly from the usual
suspects: omap, shmobile, samsung and mvebu, all of which already
contain a lot of platform specific code in arch/arm"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (187 commits)
ARM: mvebu: use the cpufreq-dt platform_data for independent clocks
soc: integrator: Add terminating entry for integrator_cm_match
ARM: mvebu: add SDRAM controller description for Armada XP
ARM: mvebu: adjust mbus controller description on Armada 370/XP
ARM: mvebu: add suspend/resume DT information for Armada XP GP
ARM: mvebu: synchronize secondary CPU clocks on resume
ARM: mvebu: make sure MMU is disabled in armada_370_xp_cpu_resume
ARM: mvebu: Armada XP GP specific suspend/resume code
ARM: mvebu: reserve the first 10 KB of each memory bank for suspend/resume
ARM: mvebu: implement suspend/resume support for Armada XP
clk: mvebu: add suspend/resume for gatable clocks
bus: mvebu-mbus: provide a mechanism to save SDRAM window configuration
bus: mvebu-mbus: suspend/resume support
clocksource: time-armada-370-xp: add suspend/resume support
irqchip: armada-370-xp: Add suspend/resume support
ARM: add lolevel debug support for asm9260
ARM: add mach-asm9260
ARM: EXYNOS: use u8 for val[] in struct exynos_pmu_conf
power: reset: imx-snvs-poweroff: add power off driver for i.mx6
ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A
...
The remaining cleanups for 3.19 are to a large part result of
devicetree conversion nearing completion on two other platforms
besides AT91:
* Like AT91, Renesas shmobile is in the process to migrate to DT and
multiplatform, but using a different approach of doing it one
SoC at a time. For 3.19, the r8a7791 platform and associated\
"Koelsch" board are considered complete and we remove the non-DT
non-multiplatform support for this.
* The ARM Versatile Express has supported DT and multiplatform
for a long time, but we have still kept the legacy board files
around, because not all drivers were fully working before. We
have finally taken the last step to remove the board files.
Other changes in this branch are preparation for the later branches
or just unrelated to the more interesting changes:
* The dts files for arm64 get moved into per-vendor directories for
a clearer structure.
* Some dead code removal (zynq, exynos, davinci, imx)
* Using pr_*() macros more consistently instead of printk(KERN_*)
in some platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Apdh
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"The remaining cleanups for 3.19 are to a large part result of
devicetree conversion nearing completion on two other platforms
besides AT91:
- Like AT91, Renesas shmobile is in the process to migrate to DT and
multiplatform, but using a different approach of doing it one SoC
at a time. For 3.19, the r8a7791 platform and associated "Koelsch"
board are considered complete and we remove the non-DT
non-multiplatform support for this.
- The ARM Versatile Express has supported DT and multiplatform for a
long time, but we have still kept the legacy board files around,
because not all drivers were fully working before. We have finally
taken the last step to remove the board files.
Other changes in this branch are preparation for the later branches or
just unrelated to the more interesting changes:
- The dts files for arm64 get moved into per-vendor directories for a
clearer structure.
- Some dead code removal (zynq, exynos, davinci, imx)
- Using pr_*() macros more consistently instead of printk(KERN_*) in
some platform code"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (71 commits)
ARM: zynq: Remove secondary_startup() declaration from header
ARM: vexpress: Enable regulator framework when MMCI is in use
ARM: vexpress: Remove non-DT code
ARM: imx: Remove unneeded .map_io initialization
ARM: dts: imx6qdl-sabresd: Fix the microphone route
ARM: imx: refactor mxc_iomux_mode()
ARM: imx: simplify clk_pllv3_prepare()
ARM: imx6q: drop unnecessary semicolon
ARM: imx: clean up machine mxc_arch_reset_init_dt reset init
ARM: dts: imx6qdl-rex: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-gw5x: Remove unneeded 'fsl,mode' property
ARM: dts: imx6qdl-sabresd: Use IMX6QDL_CLK_CKO define
ARM: at91: remove useless init_time for DT-only SoCs
ARM: davinci: Remove redundant casts
ARM: davinci: Use standard logging styles
ARM: shmobile: r8a7779: Spelling/grammar s/entity/identity/, s/map/mapping/
ARM: shmobile: sh7372: Spelling/grammar s/entity map/identity mapping/
ARM: shmobile: sh73a0: Spelling/grammar s/entity map/identity mapping/
ARM: EXYNOS: Remove unused static iomapping
ARM: at91: fix build breakage due to legacy board removals
...
On Atmel AT91, the conversion to device tree is now considered complete,
and all machines that were not already converted in 3.18 are assumed to
be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the platform
itself is not "multiplatform"-enabled, but both issues are going to be
taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size
of the branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iD8DBQBUhyNX5t5GS2LDRf4RAnjxAKCER7eoLNadu1/93n/a9d1nUz4MoQCcCZUq
BolxCOi0wr4YTcQtp7rHzWI=
=ykAB
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup on mach-at91 from Arnd Bergmann:
"On Atmel AT91, the conversion to device tree is now considered
complete, and all machines that were not already converted in 3.18 are
assumed to be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the
platform itself is not "multiplatform"-enabled, but both issues are
going to be taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size of
the branch"
* tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: at91: remove unused board.h file
ARM: at91: remove unneeded header files
ARM: at91/clocksource: remove !DT PIT initializations
ARM: at91: at91rm9200 ST initialization is now DT only
ARM: at91: remove old AT91-specific drivers
ARM: at91: cleanup initilisation code by removing dead code
ARM: at91/Kconfig: select board files automatically
ARM: at91: remove unused IRQ function declarations
ARM: at91: remove legacy IRQ driver and related code
ARM: at91: remove old at91-specific clock driver
ARM: at91: remove clock data in at91sam9n12.c and at91sam9x5.c files
ARM: at91: remove all !DT related configuration options
ARM: at91/trivial: update Kconfig comment to mention SAMA5
ARM: at91: always USE_OF from now on
ARM: at91/Kconfig: remove ARCH_AT91RM9200 option for drivers
ARM: at91: switch configuration option to SOC_AT91RM9200
ARM: at91: remove at91rm9200 legacy board support
ARM: at91: remove at91rm9200 legacy boards files
ARM: at91/Kconfig: remove useless fbdev Kconfig options
ARM: at91: remove at91sam9261/at91sam9g10 legacy board support
...
These are bug fixes for harmless problems that were not important
enough to get fixed in 3.19. This contains updates to the MAINTAINERS
file, in particular:
- Ben Dooks stepped down as Samsung co-maintainer (thanks Ben for
long years of maintaining this). Kukjin Kim, who has been
doing the work de-facto by himself recently is now the
only maintainer.
- Liviu, Sudeep and Lorenzo from ARM now officially maintain the
Versatile Express platform, which was orphaned (thanks for
- Gregory Fong and Florian Fainelli help out on the Broadcom BCM7XXX
platform
- Ray Jui and Scott Branden are the future maintainers for the
newly merged Broadcom Cygnus platform. Welcome!
In terms of actual fixes, we have the usual set of OMAP bug fixes,
which Tony Lindgren separates out well from the other OMAP changes,
one really ep93xx regression fix against 3.11 that didn't make it for
3.18, a few GIC changes from Marc Zyngier as a preparation for
later rework (the current code is wrong in a harmless way), on
Tegra regression and one samsung spelling fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAVIcj22CrR//JCVInAQJyXg/9EPrOpgNBpcCE2pfprc2JmoBqM11C8IDX
1qCP1hMbIhqfgWpoR3DptmiDpUpck5Fwn8L7M1+bIxVvSK0AAgD0n5hQI/GnmeN5
qk2jdAoUlz7tIADb3/1Yc2X8D6ZiYLakhzyi0LVcWfmsmgW1E+bcbuS4XG9RMccR
6gzuqkZqLSzneiKLN3Dqwela8Q3gHYSMFTETFaRxu7gvPkYgc622ePGvGafD7i+u
MYs/sfPwsfuNFMQ/fsdmpGQxNFghwb8Cg0VaEkSBztjV2WiDBD0GMo4Ww5UNr8e7
LvHcoHiYjtnbXHW/b5L5Uswk8BCtWp2udgDHigEbZvj2BfmMlq+qXJ72BwmQb0Nf
ow2R67yOiZ2HhG+776OcMI2BpeY6D0jFcHSNjc2Q14tgns3bhfP23taDb5rFJ8G1
5aCHoACTL6X7TkX9W2iwZ5/KWW+Ftx2ardbdzCHWtjTlD/KaK624YRWeXlLASsE1
fMpNMJidDygQHirbk7Byj2Y5IpVtvALAesyoh+VCGblzenREvdH3YE4D0onM5jWz
T1kRsv6vgiIodbYNAlgPdNXNNb134fMrYOJkWmeblHV0WIddZTcNlHjgAHK2quRJ
bAIER/A+IWKcN6sTgPfvHURcxpW8nhKsPUaSQQqqhdk1tLZquKGAg72eFW12A72f
VDMJ+337XD0=
=J1gB
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical bug fixes from Arnd Bergmann:
"These are bug fixes for harmless problems that were not important
enough to get fixed in 3.19. This contains updates to the MAINTAINERS
file, in particular:
- Ben Dooks stepped down as Samsung co-maintainer (thanks Ben for
long years of maintaining this). Kukjin Kim, who has been doing
the work de-facto by himself recently is now the only maintainer.
- Liviu, Sudeep and Lorenzo from ARM now officially maintain the
Versatile Express platform, which was orphaned (thanks for
- Gregory Fong and Florian Fainelli help out on the Broadcom BCM7XXX
platform
- Ray Jui and Scott Branden are the future maintainers for the newly
merged Broadcom Cygnus platform. Welcome!
In terms of actual fixes, we have the usual set of OMAP bug fixes,
which Tony Lindgren separates out well from the other OMAP changes,
one really ep93xx regression fix against 3.11 that didn't make it for
3.18, a few GIC changes from Marc Zyngier as a preparation for later
rework (the current code is wrong in a harmless way), on Tegra
regression and one samsung spelling fix"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx6: fix bogus use of irq_get_irq_data
ARM: imx: irq: fix buggy usage of irq_data irq field
MAINTAINERS: ARM Versatile Express platform, add missing pattern
MAINTAINERS: ARM Versatile Express platform
arm: ep93xx: add dma_masks for the M2P and M2M DMA controllers
MAINTAINERS: Add ahci_st.c to ARCH/STI architecture
MAINTAINERS: add entry for the GISB arbiter driver
MAINTAINERS: update brcmstb entries
MAINTAINERS: update email address and cleanup for exynos entry
ARM: tegra: Re-add removed SoC id macro to tegra_resume()
MAINTAINERS: Entry for Cygnus/iproc arm architecture
ARM: OMAP: serial: remove last vestige of DTR_gpio support.
ARM: OMAP2+: gpmc: Get rid of "ti,elm-id not found" warning
ARM: EXYNOS: fix typo in static struct name "exynos5_list_diable_wfi_wfe"
ARM: OMAP2: Remove unnecessary KERN_* in omap_phy_internal.c
ARM: OMAP4+: Remove unused omap_l3_noc platform init
ARM: dts: Add twl keypad map for omap3 EVM
ARM: dts: Add twl keypad map for LDP
ARM: dts: Fix NAND last partition size on LDP
ARM: OMAP3: Fix errors for omap_l3_smx when booted with device tree
Changes include:
- Support for alternative instruction patching from Andre
- seccomp from Akashi
- Some AArch32 instruction emulation, required by the Android folks
- Optimisations for exception entry/exit code, cmpxchg, pcpu atomics
- mmu_gather range calculations moved into core code
- EFI updates from Ard, including long-awaited SMBIOS support
- /proc/cpuinfo fixes to align with the format used by arch/arm/
- A few non-critical fixes across the architecture
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJUhbSAAAoJELescNyEwWM07PQH/AolxqOJTTg8TKe2wvRC+DwY
R98bcECMwhXvwep1KhTBew7z7NRzXJvVVs+EePSpXWX2+KK2aWN4L50rAb9ow4ty
PZ5EFw564g3rUpc7cbqIrM/lasiYWuIWw/BL+wccOm3mWbZfokBB2t0tn/2rVv0K
5tf2VCLLxgiFJPLuYk61uH7Nshvv5uJ6ODwdXjbrH+Mfl6xsaiKv17ZrfP4D/M4o
hrLoXxVTuuWj3sy/lBJv8vbTbKbQ6BGl9JQhBZGZHeKOdvX7UnbKH4N5vWLUFZya
QYO92AK1xGolu8a9bEfzrmxn0zXeAHgFTnRwtDCekOvy0kTR9MRIqXASXKO3ZEU=
=rnFX
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"Here's the usual mixed bag of arm64 updates, also including some
related EFI changes (Acked by Matt) and the MMU gather range cleanup
(Acked by you).
Changes include:
- support for alternative instruction patching from Andre
- seccomp from Akashi
- some AArch32 instruction emulation, required by the Android folks
- optimisations for exception entry/exit code, cmpxchg, pcpu atomics
- mmu_gather range calculations moved into core code
- EFI updates from Ard, including long-awaited SMBIOS support
- /proc/cpuinfo fixes to align with the format used by arch/arm/
- a few non-critical fixes across the architecture"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (70 commits)
arm64: remove the unnecessary arm64_swiotlb_init()
arm64: add module support for alternatives fixups
arm64: perf: Prevent wraparound during overflow
arm64/include/asm: Fixed a warning about 'struct pt_regs'
arm64: Provide a namespace to NCAPS
arm64: bpf: lift restriction on last instruction
arm64: Implement support for read-mostly sections
arm64: compat: align cacheflush syscall with arch/arm
arm64: add seccomp support
arm64: add SIGSYS siginfo for compat task
arm64: add seccomp syscall for compat task
asm-generic: add generic seccomp.h for secure computing mode 1
arm64: ptrace: allow tracer to skip a system call
arm64: ptrace: add NT_ARM_SYSTEM_CALL regset
arm64: Move some head.text functions to executable section
arm64: jump labels: NOP out NOP -> NOP replacement
arm64: add support to dump the kernel page tables
arm64: Add FIX_HOLE to permanent fixed addresses
arm64: alternatives: fix pr_fmt string for consistency
arm64: vmlinux.lds.S: don't discard .exit.* sections at link-time
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.5 (GNU/Linux)
iQIVAwUAVIVnNFWoEK+e3syCAQJHCBAArsdzkCTiFiKQwkvJSfFzOxrcdxBj7HT6
N/aSZwLvemaaXkPmHmtFnkR2YoLwM+64CJTcTCuQvZaDxV9f0RVqwD5fi05qpvFK
+tqgiUcj2Ygh9nLslN6dITk9J0F7EH8bnLrB9ZhC3yTVLwlKtR0UHB0kFglF1Qub
3wK0CR342cDEfVaDcDs3Es6cIDfPsvWGONU6z9Lf6zyTxMUdVoyQ5RHAsOqJsHUI
en4E7/uHRRWeqU6ZCBMP6K+24q4m5VmEgommotZQxAKYkpQHMGMfgVZ0dashQIt2
JmEm1++YS9lrfJhnzNqJuhHp7tOHsGSPkEgTqvYWU/5D7lqQCkf4uam5rhCun2ht
Ng9uOR1c34L+smiUvKPz4d0N59Jyv5zF0lsIynmluYNlArvkmjqbSJqtvN+Oc6SP
VP/JbgjUkzsLrNrNay6/S2/hPXgC4lst+fkpRmLPzcflGrFtUHfIKV2hNl4j8oMa
skHwjhzsREqWZXtXaGAb6MdpVISzNYqEs5A8gvfb1AWE/GpEFHqg7eipjmEEqtuu
T+dfcI/tjEeUnWJzjvd86yEWZgstBh4ivoVDDcAuYPVG334L03U0EZ5/PzbCZUeU
RO5xQT/gfwqLImIUi8iRFNI8ASeCYK+8WVQ/VFsPOidvF17sTfRRXCku7EaOJEJQ
rA3Zo8qaPhE=
=KmRf
-----END PGP SIGNATURE-----
Merge tag 'nios2-v3.19-rc1' of git://git.rocketboards.org/linux-socfpga-next
Pull Altera Nios II processor support from Ley Foon Tan:
"Here is the Linux port for Nios II processor (from Altera) arch/nios2/
tree for v3.19.
The patchset has been discussed on the kernel mailing lists since
April and has gone through 6 revisions of review. The additional
changes since then have been mostly further cleanups and fixes when
merged with other trees.
The arch code is in arch/nios2 and one asm-generic change (acked by
Arnd)"
Arnd Bergmann says:
"I've reviewed the architecture port in the past and it looks good in
its latest version"
Acked-by: Arnd Bergmann <arnd@arndb.de>
* tag 'nios2-v3.19-rc1' of git://git.rocketboards.org/linux-socfpga-next: (40 commits)
nios2: Make NIOS2_CMDLINE_IGNORE_DTB depend on CMDLINE_BOOL
nios2: Add missing NR_CPUS to Kconfig
nios2: asm-offsets: Remove unused definition TI_TASK
nios2: Remove write-only struct member from nios2_timer
nios2: Remove unused extern declaration of shm_align_mask
nios2: include linux/type.h in io.h
nios2: move include asm-generic/io.h to end of file
nios2: remove include asm-generic/iomap.h from io.h
nios2: remove unnecessary space before define
nios2: fix error handling of irq_of_parse_and_map
nios2: Use IS_ENABLED instead of #ifdefs to check config symbols
nios2: Build infrastructure
Documentation: Add documentation for Nios2 architecture
MAINTAINERS: Add nios2 maintainer
nios2: ptrace support
nios2: Module support
nios2: Nios2 registers
nios2: Miscellaneous header files
nios2: Cpuinfo handling
nios2: Time keeping
...
This patch is the usual mix of driver updates (srp, ipr, scsi_debug, NCR5380,
fnic, 53c974, ses, wd719x, hpsa, megaraid_sas). Of those, wd7a9x is new and
53c974 is a rewrite of the old tmscsim driver and the extensive work by Finn
Thain rewrites all the NCR5380 based drivers. There's also extensive
infrastructure updates: a new logging infrastructure for sense information and
a rewrite of the tagged command queue API and an assortment of minor updates.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJUhgazAAoJEDeqqVYsXL0MxIYH/2wCs9sne5cfDTjfufLJDdu1
WLoJgNMxv+14OukknJfG2Kk1WlHgLRM5+TVWIGiG0mmjXuFyShzIqEOHKTDWqxnE
tBH4wLi/+XYqZAmAeim4/2zhvf+cUVVlIu01VERR5uwaBWYM8BeLSwjdnAAvEEwb
iV74p1WV6frXo4guADplgtkjD0YxI4MTUZ1figRMlLO6WLFFyQ+95UfY8jFs+eQv
zk63y7Mm7dQNd57/Wl3i89lw0kqlaJSZNl8Ovj1axy4rDYzT1wXhY8mEwD8fI8Ym
wahldjFE5vXgj0NpO3tB3Z+UDP2YmQduMyzTxkPNnrEPKiOCsnQo42XR6vb92cQ=
=Y+DU
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch is the usual mix of driver updates (srp, ipr, scsi_debug,
NCR5380, fnic, 53c974, ses, wd719x, hpsa, megaraid_sas).
Of those, wd7a9x is new and 53c974 is a rewrite of the old tmscsim
driver and the extensive work by Finn Thain rewrites all the NCR5380
based drivers.
There's also extensive infrastructure updates: a new logging
infrastructure for sense information and a rewrite of the tagged
command queue API and an assortment of minor updates"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (183 commits)
scsi: set fmt to NULL scsi_extd_sense_format() by default
libsas: remove task_collector mode
wd719x: remove dma_cache_sync call
scsi_debug: add Report supported opcodes+tmfs; Compare and write
scsi_debug: change SCSI command parser to table driven
scsi_debug: add Capacity Changed Unit Attention
scsi_debug: append inject error flags onto scsi_cmnd object
scsi_debug: pinpoint invalid field in sense data
wd719x: Add firmware documentation
wd719x: Introduce Western Digital WD7193/7197/7296 PCI SCSI card driver
eeprom-93cx6: Add (read-only) support for 8-bit mode
esas2r: fix an oversight in setting return value
esas2r: fix an error path in esas2r_ioctl_handler
esas2r: fir error handling in do_fm_api
scsi: add SPC-3 command definitions
scsi: rename SERVICE_ACTION_IN to SERVICE_ACTION_IN_16
scsi: remove scsi_driver owner field
scsi: move scsi_dispatch_cmd to scsi_lib.c
scsi: stop passing a gfp_mask argument down the command setup path
scsi: remove scsi_next_command
...
New driver for NCT7802Y
Add support for TMP435, LM95233, LM95235, NCT6792D, and NXP LM75B
Add regulator support for PMBus chips, specifically LTX2978
Add support for humidity sensors to iio-hwmon bridge driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=f0Ih
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"Notable changes:
- new driver for NCT7802Y
- support for TMP435, LM95233, LM95235, NCT6792D, and NXP LM75B
- regulator support for PMBus chips, specifically LTX2978
- support for humidity sensors to iio-hwmon bridge driver
* tag 'hwmon-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (21 commits)
hwmon: (tmp401) Detect TMP435 on all addresses it supports
hwmon: (lm75) Strengthen detect function
hwmon: (gpio-fan) Add a shutdown handler to poweroff the fans
hwmon: (gpio-fan) Allow usage of gpio operations that may sleep
hwmon: (tmp401) Bail out from tmp401_probe() in case of write errors
hwmon: (tmp401) Add support for TI TMP435
hwmon: (lm95234) Add support for LM95233
hwmon: (lm95245) Add support for LM95235
hwmon: (ina2xx) bail-out from ina2xx_probe() in case of configuration errors
hwmon: (nct6775) Add blank lines after declarations
hwmon: (nct6775) Add support for NCT6792D
hwmon: (nct6775) Documentation updates
hwmon: (lm75) Add support for the NXP LM75B
hwmon: Driver for Nuvoton NCT7802Y
hwmon: (ibmpowernv) Convert to module_platform_driver
hwmon: (ibmpowernv) Use platform 'id_table' to probe the device
hwmon: (iio_hwmon) Add support for humidity sensors
hwmon: (ltc2978) Add regulator support
hwmon: (pmbus) Add regulator support
hwmon: (pmbus) add helpers for byte write and read modify write
...
* Enablement for AMD F15h models 0x60 CPUs. Most notably DDR4 RAM
support. Out of tree stuff is
arch/x86/kernel/amd_nb.c | 2 +
include/linux/pci_ids.h | 2 +
adding the required PCI IDs. From Aravind Gopalakrishnan.
* Enable amd64_edac for 32-bit due to popular demand. From Tomasz Pala.
* Convert the AMD MCE injection module to debugfs, where it belongs.
* Misc EDAC cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ULmb
-----END PGP SIGNATURE-----
Merge tag 'edac_for_3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"EDAC updates all over the place:
- Enablement for AMD F15h models 0x60 CPUs. Most notably DDR4 RAM
support. Out of tree stuff is adding the required PCI IDs. From
Aravind Gopalakrishnan.
- Enable amd64_edac for 32-bit due to popular demand. From Tomasz
Pala.
- Convert the AMD MCE injection module to debugfs, where it belongs.
- Misc EDAC cleanups"
* tag 'edac_for_3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, MCE, AMD: Correct formatting of decoded text
EDAC, mce_amd_inj: Add an injector function
EDAC, mce_amd_inj: Add hw-injection attributes
EDAC, mce_amd_inj: Enable direct writes to MCE MSRs
EDAC, mce_amd_inj: Convert mce_amd_inj module to debugfs
EDAC: Delete unnecessary check before calling pci_dev_put()
EDAC, pci_sysfs: remove unneccessary ifdef around entire file
ghes_edac: Use snprintf() to silence a static checker warning
amd64_edac: Build module on x86-32
EDAC, MCE, AMD: Add decoding table for MC6 xec
amd64_edac: Add F15h M60h support
{mv64x60,ppc4xx}_edac,: Remove deprecated IRQF_DISABLED
EDAC: Sync memory types and names
EDAC: Add DDR3 LRDIMM entries to edac_mem_types
x86, amd_nb: Add device IDs to NB tables for F15h M60h
pci_ids: Add PCI device IDs for F15h M60h
- Consolidation and cleanups.
- Some improvements regarding error handling.
- Increase maximum amount of block devices.
- Use correct OCR mask for SDIO when restoring power.
- Fix prepared requests while doing BKOPS.
- Convert to modern PM ops.
- Add mmc_send_tuning() API and convert some hosts to use it.
MMC host:
- toshsd: New Toshiba PCI SD controller driver.
- sdhci: 64-bit ADMA support.
- sdhci: Some regulator fixes.
- sdhci: HS400 support.
- sdhci: Various fixes cleanups.
- atmel-mci: Modernization and cleanups.
- atmel-mci: Runtime PM support.
- omap_hsmmc: Modernization and cleanups.
- omap_hsmmc: Fix UHS card with DDR50 support.
- dw_mmc: Support for ARM64 and Exynos 7 variant.
- dw_mmc: Add support for IMG Pistachio variant.
- dw_mmc: Various fixes and cleanups.
- mvsdio: DMA fixes.
- mxs-mmc: Modernization and cleanups.
- mxcmmc: Various fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ODSj
-----END PGP SIGNATURE-----
Merge tag 'mmc-v3.19-1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Consolidation and cleanups.
- Some improvements regarding error handling.
- Increase maximum amount of block devices.
- Use correct OCR mask for SDIO when restoring power.
- Fix prepared requests while doing BKOPS.
- Convert to modern PM ops.
- Add mmc_send_tuning() API and convert some hosts to use it.
MMC host:
- toshsd: New Toshiba PCI SD controller driver.
- sdhci: 64-bit ADMA support.
- sdhci: Some regulator fixes.
- sdhci: HS400 support.
- sdhci: Various fixes cleanups.
- atmel-mci: Modernization and cleanups.
- atmel-mci: Runtime PM support.
- omap_hsmmc: Modernization and cleanups.
- omap_hsmmc: Fix UHS card with DDR50 support.
- dw_mmc: Support for ARM64 and Exynos 7 variant.
- dw_mmc: Add support for IMG Pistachio variant.
- dw_mmc: Various fixes and cleanups.
- mvsdio: DMA fixes.
- mxs-mmc: Modernization and cleanups.
- mxcmmc: Various fixes"
* tag 'mmc-v3.19-1' of git://git.linaro.org/people/ulf.hansson/mmc: (126 commits)
mmc: sdhci-msm: Convert to mmc_send_tuning()
mmc: sdhci-esdhc-imx: Convert to mmc_send_tuning()
mmc: core: Let mmc_send_tuning() to take struct mmc_host* as parameter
mmc: queue: Improve error handling during allocation of bounce buffers
mmc: sdhci-acpi: Add two host capabilities for Intel
mmc: sdhci-pci: Add two host capabilities for BYT
mmc: sdhci-acpi: Add SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC
mmc: sdhci-pci: Add SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC to BYT
mmc: atmel-mci: use probe deferring if dma controller is not ready yet
mmc: atmel-mci: stop using specific initcall
mmc: atmel-mci: remove __init/__exit attributes
mmc: atmel-mci: remove useless DMA stuff for non-dt devices
mmc: omap_hsmmc: Fix UHS card with DDR50 support
mmc: core: add core-level function for sending tuning commands
mmc: core: hold SD Clock before CMD11 during Signal
mmc: mxs-mmc: Check for clk_prepare_enable() error
mmc: mxs-mmc: Propagate the real error
mmc: mxs-mmc: No need to do NULL check on 'iores'
mmc: dw_mmc: Add support for IMG Pistachio
mmc: mxs-mmc: Simplify PM hooks
...
Linus Torvalds
Johan Hovold
Joe Perches
Yann Droneaud
Kirill A. Shutemov
Dan Carpenter
Borislav Petkov
Al Viro