Add keymaps and imx_keypad device registration for imx51_3ds board.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
add imx_keypad platform device definition and clocks for mx51
platforms.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
3-stack is a reference board from Freescale for their i.MX51 SoC.
Add board definition, Kconfig and Makefile to enable Freescale 3-stack
board.
Boot tested on a i.MX51 3-stack Rev2.0 board
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
mx27_3ds: add support for the keypad
Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Because we add a 3ds debug board support in mxc level, we remove
those redundant codes from board level.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The debug board is little different for all mxc 3-stack(PDK)
platforms, it is possible here to add a common implementation to
support this board.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There are some more conflicts than detected by git, namely support for
the newly added cpuimx machines needed to be converted to dynamic device
registration.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Conflicts:
arch/arm/mach-imx/Makefile
arch/arm/mach-imx/devices.c
arch/arm/mach-imx/devices.h
arch/arm/mach-imx/eukrea_mbimx27-baseboard.c
arch/arm/mach-mx2/Kconfig
arch/arm/mach-mx25/Makefile
arch/arm/mach-mx25/devices.c
arch/arm/plat-mxc/include/mach/mx25.h
arch/arm/plat-mxc/include/mach/mxc_nand.h
cleaned up some duplicated mxc_gpio_mode calls and move the correpsonding
pin multiplexing either into the initial pin config table or ifdef blocks.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this one adds the frambuffer device and a TFT panel to the PhyCard-S
(pca100) board.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
These GPIO bank offsets are useful when define a gpio number.
E.G. when GPIO PORTC pin 6 is used for irq request pin of external
expanding device, we can define it like:
#define EXP_PARENT_IRQ_PIN (GPIO_PORTC + 6)
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add UART2 CTS/RTS and UART3 RXD/TXD pad definitons for imx51_3ds board,
add GPIO_1_6 definiton because this pin is used as a CPLD parent irq
request pin on imx51_3ds board.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For pad EIM_D27 to work in UART3_RTS mode, the input path should be
3 instead of 0; for pad USBH1_STP to work in GPIO_1_27 mode, the mux
value should be 2 instead of 8.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The pads capable of being used as GPIOs had their pad-name and mode-name
switched. Also, fix the following:
- Whitespace fixes
- Replace IOMUX_CONFIG_ALTn with 'n'
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The information in the i.MX25 Reference Manual is lacking. Add information from
the Freescale BSP.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
usb drivers need to get the right value for otg clock so
calculate and return it
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
i.MX25's OTG has the same USBCTRL registers than i.MX35 so reuse
most of the i.MX35's defines.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the standard place for this define is include/mach/mx25.h
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
when CONFIG_USB_ULPI is not defined we actually get :
warning: 'otg_pdata' defined but not used
warning: 'usbh2_pdata' defined but not used
Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: s.hauer@pengutronix.de
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
without this patch, ipu_clk's value is 0 thus preventing mx3fb from
calculating the right divisor for pixel clock generator.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes the clock refcounting when reparenting is used.
Boot-tested on imx51 babbage board.
Sascha pointed out a good explanation of refcounting here:
http://www.spinics.net/lists/arm-kernel/msg85879.html
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The keymap is taken from the Freescale supplied kernel.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The OOB handling in the mxc_nand driver is broken for v1 type
controllers (i.MX27/31) with 512 byte page size. This perhaps
did not show up because ubi does not use OOB.
Update the driver to always read/write a whole page even if
only OOB is requested. With this patch the driver passes the
mtd_oobtest on i.MX27 with 512 byte page size. Also tested
with 2048 byte page size and on i.MX35 (v2 type controller)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reported-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Jason Wang
Rogerio Pimentel
Uwe Kleine-König
Baruch Siach
Fabio Estevam
Luotao Fu
Amit Kucheria
Eric Bénard
Dinh Nguyen
Amit Kucheria
Sascha Hauer