ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
* pci/virtualization:
PCI: Add comments about ROM BAR updating
PCI: Decouple IORESOURCE_ROM_ENABLE and PCI_ROM_ADDRESS_ENABLE
PCI: Remove pci_resource_bar() and pci_iov_resource_bar()
PCI: Don't update VF BARs while VF memory space is enabled
PCI: Separate VF BAR updates from standard BAR updates
PCI: Update BARs using property bits appropriate for type
PCI: Ignore BAR updates on virtual functions
PCI: Do any VF BAR updates before enabling the BARs
PCI: Support INTx masking on ConnectX-4 with firmware x.14.1100+
PCI: Convert Mellanox broken INTx quirks to be for listed devices only
PCI: Convert broken INTx masking quirks from HEADER to FINAL
net/mlx4_core: Use device ID defines
PCI: Add Mellanox device IDs
There is at least one Chelsio 10Gb card which uses VPD area to store some
non-standard blocks (example below). However pci_vpd_size() returns the
length of the first block only assuming that there can be only one VPD "End
Tag".
Since 4e1a635552 ("vfio/pci: Use kernel VPD access functions"), VFIO
blocks access beyond that offset, which prevents the guest "cxgb3" driver
from probing the device. The host system does not have this problem as its
driver accesses the config space directly without pci_read_vpd().
Add a quirk to override the VPD size to a bigger value. The maximum size
is taken from EEPROMSIZE in drivers/net/ethernet/chelsio/cxgb3/common.h.
We do not read the tag as the cxgb3 driver does as the driver supports
writing to EEPROM/VPD and when it writes, it only checks for 8192 bytes
boundary. The quirk is registered for all devices supported by the cxgb3
driver.
This adds a quirk to the PCI layer (not to the cxgb3 driver) as the cxgb3
driver itself accesses VPD directly and the problem only exists with the
vfio-pci driver (when cxgb3 is not running on the host and may not be even
loaded) which blocks accesses beyond the first block of VPD data. However
vfio-pci itself does not have quirks mechanism so we add it to PCI.
This is the controller:
Ethernet controller [0200]: Chelsio Communications Inc T310 10GbE Single Port Adapter [1425:0030]
This is what I parsed from its VPD:
===
b'\x82*\x0010 Gigabit Ethernet-SR PCI Express Adapter\x90J\x00EC\x07D76809 FN\x0746K'
0000 Large item 42 bytes; name 0x2 Identifier String
b'10 Gigabit Ethernet-SR PCI Express Adapter'
002d Large item 74 bytes; name 0x10
#00 [EC] len=7: b'D76809 '
#0a [FN] len=7: b'46K7897'
#14 [PN] len=7: b'46K7897'
#1e [MN] len=4: b'1037'
#25 [FC] len=4: b'5769'
#2c [SN] len=12: b'YL102035603V'
#3b [NA] len=12: b'00145E992ED1'
007a Small item 1 bytes; name 0xf End Tag
0c00 Large item 16 bytes; name 0x2 Identifier String
b'S310E-SR-X '
0c13 Large item 234 bytes; name 0x10
#00 [PN] len=16: b'TBD '
#13 [EC] len=16: b'110107730D2 '
#26 [SN] len=16: b'97YL102035603V '
#39 [NA] len=12: b'00145E992ED1'
#48 [V0] len=6: b'175000'
#51 [V1] len=6: b'266666'
#5a [V2] len=6: b'266666'
#63 [V3] len=6: b'2000 '
#6c [V4] len=2: b'1 '
#71 [V5] len=6: b'c2 '
#7a [V6] len=6: b'0 '
#83 [V7] len=2: b'1 '
#88 [V8] len=2: b'0 '
#8d [V9] len=2: b'0 '
#92 [VA] len=2: b'0 '
#97 [RV] len=80: b's\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00'...
0d00 Large item 252 bytes; name 0x11
#00 [VC] len=16: b'122310_1222 dp '
#13 [VD] len=16: b'610-0001-00 H1\x00\x00'
#26 [VE] len=16: b'122310_1353 fp '
#39 [VF] len=16: b'610-0001-00 H1\x00\x00'
#4c [RW] len=173: b'\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00'...
0dff Small item 0 bytes; name 0xf End Tag
10f3 Large item 13315 bytes; name 0x62
!!! unknown item name 98: b'\xd0\x03\x00@`\x0c\x08\x00\x00\x00\x00\x00\x00\x00\x00\x00'
===
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It's not very enlightening to see
pci 0000:07:00.0: [Firmware Bug]: VPD access disabled
in the dmesg log because there's no clue about what the firmware bug is.
Expand the message to explain why we're disabling VPD.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Mellanox devices were marked as having INTx masking ability broken. As a
result, the VFIO driver fails to start when more than one device function
is passed-through to a VM if both have the same INTx pin.
Prior to Connect-IB, Mellanox devices exposed to the operating system one
PCI function per all ports. Starting from Connect-IB, the devices are
function-per-port. When passing the second function to a VM, VFIO will
fail to start.
Exclude ConnectX-4, ConnectX4-Lx and Connect-IB from the list of Mellanox
devices marked as having broken INTx masking:
- ConnectX-4 and ConnectX4-LX firmware version is checked. If INTx
masking is supported, we unmark the broken INTx masking.
- Connect-IB does not support INTx currently so will not cause any
problem.
[bhelgaas: call pci_disable_device() always, after iounmap()]
Fixes: 11e42532ad ("PCI: Assume all Mellanox devices have broken INTx masking")
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Change Mellanox's broken_intx_masking() quirk from an "all Mellanox
devices" to a quirk for listed devices only.
[bhelgaas: remove #defines, reorder to keep other quirks together]
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Convert all quirk_broken_intx_masking() quirks from HEADER to FINAL.
The quirk sets dev->broken_intx_masking, which is only used by
pci_intx_mask_supported(), which is not needed until after FINAL
quirks have been run.
[bhelgaas: changelog]
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.9:
API:
- The crypto engine code now supports hashes.
Algorithms:
- Allow keys >= 2048 bits in FIPS mode for RSA.
Drivers:
- Memory overwrite fix for vmx ghash.
- Add support for building ARM sha1-neon in Thumb2 mode.
- Reenable ARM ghash-ce code by adding import/export.
- Reenable img-hash by adding import/export.
- Add support for multiple cores in omap-aes.
- Add little-endian support for sha1-powerpc.
- Add Cavium HWRNG driver for ThunderX SoC"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (137 commits)
crypto: caam - treat SGT address pointer as u64
crypto: ccp - Make syslog errors human-readable
crypto: ccp - clean up data structure
crypto: vmx - Ensure ghash-generic is enabled
crypto: testmgr - add guard to dst buffer for ahash_export
crypto: caam - Unmap region obtained by of_iomap
crypto: sha1-powerpc - little-endian support
crypto: gcm - Fix IV buffer size in crypto_gcm_setkey
crypto: vmx - Fix memory corruption caused by p8_ghash
crypto: ghash-generic - move common definitions to a new header file
crypto: caam - fix sg dump
hwrng: omap - Only fail if pm_runtime_get_sync returns < 0
crypto: omap-sham - shrink the internal buffer size
crypto: omap-sham - add support for export/import
crypto: omap-sham - convert driver logic to use sgs for data xmit
crypto: omap-sham - change the DMA threshold value to a define
crypto: omap-sham - add support functions for sg based data handling
crypto: omap-sham - rename sgl to sgl_tmp for deprecation
crypto: omap-sham - align algorithms on word offset
crypto: omap-sham - add context export/import stubs
...
* pci/virtualization:
PCI: xilinx: Relax device number checking to allow SR-IOV
PCI: designware: Relax device number checking to allow SR-IOV
PCI: altera: Relax device number checking to allow SR-IOV
PCI: Check for pci_setup_device() failure in pci_iov_add_virtfn()
PCI: Mark Atheros AR9580 to avoid bus reset
The newly added quirk_cavium_sriov_rnm_link doesn't compile if
PCI_ATS is off. This patch adds a check for PCI_ATS.
Fixes: 21b5b8eebb ("PCI: quirk fixup for cavium invalid sriov...")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
VMD root ports change all source ids to the VMD device ID. To find the
sender of the AER notification, we need to scan all child devices for the
AER sender, rather than relying on the source ID from the message.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
From: Xavier Gnata <xavier.gnata@gmail.com>
Add support to INTEL_FALCON_RIDGE_2C controller and corresponding quirk
to support suspend/resume.
Tested against 4.7 master on a MacBook Air 11" 2015.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The quirk 'quirk_apple_wait_for_thunderbolt' did not fire on Falcon
Ridge 4C controllers with subdevice/subvendor set to zero. This lead
to lost pci devices on system resume.
Older thunderbolt controllers (pre Falcon Ridge) used the same device id
for bridges and for the controller. On Apple hardware the subvendor- &
subdevice-ids were set for the controller, but not for bridges. So that
is what was used to differentiate between the two. Starting with Falcon
Ridge bridges and controllers received different device ids.
Additionally on some MacBookPro models (but not all) the
subvendor/subdevice was zeroed.
Starting with a42fb351c (thunderbolt: Allow loading of module on recent
Apple MacBooks with thunderbolt 2 controller) the thunderbolt driver
binds to all Falcon Ridge 4C controllers (irregardless of
subvendor/subdevice). The corresponding quirk was not updated.
This commit changes the quirk to check the device class instead of its
subvendor-/subdeviceids. This works for all generations of Thunderbolt
controllers.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to the AR93xx and the AR94xx series, the AR95xx also have the same
quirk for the Bus Reset. It will lead to instant system reset if the
device is assigned via VFIO to a KVM VM. I've been able reproduce this
behavior with a MikroTik R11e-2HnD.
Fixes: c3e59ee4e7 ("PCI: Mark Atheros AR93xx to avoid bus reset")
Signed-off-by: Maik Broemme <mbroemme@libmpq.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
The Solarflare SFC9220 apparently lacks an ACS capability, but does not
perform peer-to-peer between functions. Add a quirk so we know about this
isolation.
[bhelgaas: changelog]
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a DMA alias quirk for the Adaptec 3805, just like the 3405 quirk added
in commit d3d2ab43dd ("PCI: Add DMA alias quirk for Adaptec 3405").
Link: https://www.redhat.com/archives/vfio-users/2016-July/msg00046.html
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Similar to the AR93xx series, the AR94xx and the Qualcomm QCA988x also have
the same quirk for the Bus Reset.
Fixes: c3e59ee4e7 ("PCI: Mark Atheros AR93xx to avoid bus reset")
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
Add function 1 DMA alias quirk for Marvell 88SE9182.
We found this quirk reported in the same thread as other Marvell
devices, but no patch resulted:
https://bugzilla.kernel.org/show_bug.cgi?id=42679#c78
Signed-off-by: Steven Graham <sgraham@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Intel Sunrise Point root ports implement ACS but use dwords for the
capability and control registers, putting the control register at the wrong
offset.
Use quirks to enable and test ACS for these devices, which match the
standard functions modulo the broken control register offset.
Note that lspci assumes devices implement ACS per spec, so it shows invalid
ACS data for these devices.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The original thought was that if a device implemented ACS, then surely
we want to use that... well, it turns out that devices can make an ACS
capability so broken that we still need to fall back to quirks.
Reverse the order of ACS enabling to give quirks first shot at it.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
All of the i40e (XL710/X710) 10/20/40GbE NICs lack support for indicating
INTx is asserted via the interrupt bit in the PCI status register. The
DisINTx bit in the command register is functional, causing these devices to
be incorrectly detected as supporting INTx masking. Quirk them to properly
indicate no INTx masking support.
Device IDs copied from i40e_devids.h.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
The MIC x200 NTB forwards DMA transactions upstream using multiple alien
RIDs. These RIDs have to be added as aliases to the DMA device to allow
buffer access when the IOMMU is enabled.
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
One of the quirks that adds DMA aliases logs an informational message in
dmesg. Move that to pci_add_dma_alias() so all users log the message
consistently. No functional change intended (except extra message).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Add a pci_add_dma_alias() interface to encapsulate the details of adding an
alias. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Add support for the 1st gen Light Ridge controller, which is built into
these systems:
iMac12,1 2011 21.5"
iMac12,2 2011 27"
Macmini5,1 2011 i5 2.3 GHz
Macmini5,2 2011 i5 2.5 GHz
Macmini5,3 2011 i7 2.0 GHz
MacBookPro8,1 2011 13"
MacBookPro8,2 2011 15"
MacBookPro8,3 2011 17"
MacBookPro9,1 2012 15"
MacBookPro9,2 2012 13"
Light Ridge (CV82524) was the very first copper Thunderbolt controller,
introduced 2010 alongside its fiber-optic cousin Light Peak (CVL2510).
Consequently the chip suffers from some teething troubles:
- MSI is broken for hotplug signaling on the downstream bridges: The chip
just never sends an interrupt. It requests 32 MSIs for each of its six
bridges and the pcieport driver only allocates one per bridge. However
I've verified that even if 32 MSIs are allocated there's no interrupt
on hotplug. The only option is thus to disable MSI, which is also what
OS X does. Apparently all Thunderbolt chips up to revision 1 of Cactus
Ridge 4C are plagued by this issue so quirk those as well.
- The chip supports a maximum hop_count of 32, unlike its successors
which support only 12. Fixup ring_interrupt_active() to cope with
values >= 32.
- Another peculiarity is that the chip supports a maximum of 13 ports
whereas its successors support 12. However the additional port (#5)
seems to be unusable as reading its TB_CFG_PORT config space results in
TB_CFG_ERROR_INVALID_CONFIG_SPACE. Add a quirk to mark the port
disabled on the root switch, assuming that's necessary on all Macs
using this chip.
Tested-by: Lukas Wunner <lukas@wunner.de> [MacBookPro9,1]
Tested-by: William Brown <william@blackhats.net.au> [MacBookPro8,2]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Intel Gen 1 and 2 chips use the same ID for NHI, bridges and switch. Gen 3
chips and onward use a distinct ID for the NHI.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
* pci/aer:
PCI/AER: Log aer_inject error injections
PCI/AER: Log actual error causes in aer_inject
PCI/AER: Use dev_warn() in aer_inject
PCI/AER: Fix aer_inject error codes
* pci/enumeration:
PCI: Fix broken URL for Dell biosdevname
* pci/kconfig:
PCI: Cleanup pci/pcie/Kconfig whitespace
PCI: Include pci/hotplug Kconfig directly from pci/Kconfig
PCI: Include pci/pcie/Kconfig directly from pci/Kconfig
* pci/misc:
PCI: Add PCI_CLASS_SERIAL_USB_DEVICE definition
PCI: Add QEMU top-level IDs for (sub)vendor & device
unicore32: Remove unused HAVE_ARCH_PCI_SET_DMA_MASK definition
PCI: Consolidate PCI DMA constants and interfaces in linux/pci-dma-compat.h
PCI: Move pci_dma_* helpers to common code
frv/PCI: Remove stray pci_{alloc,free}_consistent() declaration
* pci/virtualization:
PCI: Wait for up to 1000ms after FLR reset
PCI: Support SR-IOV on any function type
* pci/vpd:
PCI: Prevent VPD access for buggy devices
PCI: Sleep rather than busy-wait for VPD access completion
PCI: Fold struct pci_vpd_pci22 into struct pci_vpd
PCI: Rename VPD symbols to remove unnecessary "pci22"
PCI: Remove struct pci_vpd_ops.release function pointer
PCI: Move pci_vpd_release() from header file to pci/access.c
PCI: Move pci_read_vpd() and pci_write_vpd() close to other VPD code
PCI: Determine actual VPD size on first access
PCI: Use bitfield instead of bool for struct pci_vpd_pci22.busy
PCI: Allow access to VPD attributes with size 0
PCI: Update VPD definitions
PCI-SIG has defined Interface FEh for Base Class 0Ch, Sub-Class 03h as "USB
Device (not host controller)". It is already being used in various USB
device controller drivers for matching, so add PCI_CLASS_SERIAL_USB_DEVICE
and use it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On some devices, reading or writing VPD causes a system panic.
This can be easily reproduced by running "lspci -vvv" or
"cat /sys/bus/devices/XX../vpd".
Blacklist these devices so we don't access VPD data at all.
[bhelgaas: changelog, comment, drop pci/access.c changes]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=110681
Tested-by: Shane Seymour <shane.seymour@hpe.com>
Tested-by: Babu Moger <babu.moger@oracle.com>
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Cavium devices matching this quirk do not perform peer-to-peer with other
functions, allowing masking out these bits as if they were unimplemented in
the ACS capability.
Signed-off-by: Manish Jaggi <mjaggi@caviumnetworks.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tirumalesh Chalamarla <tchalamarla@cavium.com>
* pci/iommu:
PCI: Add function 1 DMA alias quirk for Lite-On/Plextor M6e/Marvell 88SS9183
* pci/misc:
PCI: Limit config space size for Netronome NFP4000
PCI: Add Netronome NFP4000 PF device ID
Add function 1 DMA alias quirk for Lite-On/Plextor M6e/Marvell 88SS9183.
Signed-off-by: Tim Sander <tim@krieglstein.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Like the NFP6000, the NFP4000 as an erratum where reading/writing to PCI
config space addresses above 0x600 can cause the NFP to generate PCIe
completion timeouts.
Limit the NFP4000's PF's config space size to 0x600 bytes as is already
done for the NFP6000.
The NFP4000's VF is 0x6004 (PCI_DEVICE_ID_NETRONOME_NFP6000_VF), the same
device ID as the NFP6000's VF. Thus, its config space is already limited
by the existing use of quirk_nfp6000().
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The NFP6000 has an erratum where reading/writing to PCI config space
addresses above 0x600 can cause the NFP to generate PCIe completion
timeouts.
Limit the NFP6000's config space size to 0x600 bytes.
Signed-off-by: Jason S. McMullan <jason.mcmullan@netronome.com>
[simon: edited changelog]
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWUmHZAAoJEHm+PkMAQRiGHtcH/RVRsn8re0WdRWYaTr9+Hknm
CGlRJN4LKecttgYQ/2bS1QsDbt8usDPBiiYVopqGXQxPBmjyDAqPjsa+8VzCaVc6
WA+9LDB+PcW28lD6BO+qSZCOAm7hHSZq7dtw9x658IqO+mI2mVeCybsAyunw2iWi
Kf5q90wq6tIBXuT8YH9MXGrSCQw00NclbYeYwB9CmCt9hT/koEFBdl7uFUFitB+Q
GSPTz5fXhgc5Lms85n7flZlrVKoQKmtDQe4/DvKZm+SjsATHU9ru89OxDBdS5gSG
YcEIM4zc9tMjhs3GC9t6WXf6iFOdctum8HOhUoIN/+LVfeOMRRwAhRVqtGJ//Xw=
=DCUg
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rc2' into drm-intel-next-queued
Linux 4.4-rc2
Backmerge to get at
commit 1b0e3a049e
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Nov 5 23:04:11 2015 +0200
drm/i915/skl: disable display side power well support for now
so that we can proplery re-eanble skl power wells in -next.
Conflicts are just adjacent lines changed, except for intel_fbdev.c
where we need to interleave the changs. Nothing nefarious.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
i915 register defines are going to become type safe, so going forward
the register defines can't be used as straight numbers. Since quirks.c
needs just a few extra register defines from i915_reg.h, decouple the
two by defining the required registers locally in quirks.c. This was
already done for a few other igpu related registers.
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446672017-24497-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
* pci/aer:
PCI/AER: Clear error status registers during enumeration and restore
* pci/hotplug:
PCI: pciehp: Queue power work requests in dedicated function
* pci/misc:
PCI: Turn off Request Attributes to avoid Chelsio T5 Completion erratum
x86/PCI: Make pci_subsys_init() static
PCI: Add builtin_pci_driver() to avoid registration boilerplate
PCI: Remove unnecessary "if" statement
* pci/msi:
x86/PCI: Don't alloc pcibios-irq when MSI is enabled
PCI/MSI: Export all remapped MSIs to sysfs attributes
PCI: Disable MSI on SiS 761
* pci/resource:
sparc/PCI: Add mem64 resource parsing for root bus
PCI: Expand Enhanced Allocation BAR output
PCI: Make Enhanced Allocation bitmasks more obvious
PCI: Handle Enhanced Allocation capability for SR-IOV devices
PCI: Add support for Enhanced Allocation devices
PCI: Add Enhanced Allocation register entries
PCI: Handle IORESOURCE_PCI_FIXED when assigning resources
PCI: Handle IORESOURCE_PCI_FIXED when sizing resources
PCI: Clear IORESOURCE_UNSET when reverting to firmware-assigned address
* pci/virtualization:
PCI: Fix sriov_enable() error path for pcibios_enable_sriov() failures
PCI: Wait 1 second between disabling VFs and clearing NumVFs
PCI: Reorder pcibios_sriov_disable()
PCI: Remove VFs in reverse order if virtfn_add() fails
PCI: Remove redundant validation of SR-IOV offset/stride registers
PCI: Set SR-IOV NumVFs to zero after enumeration
PCI: Enable SR-IOV ARI Capable Hierarchy before reading TotalVFs
PCI: Don't try to restore VF BARs
The Chelsio T5 has a PCIe compliance erratum that causes Malformed TLP or
Unexpected Completion errors in some systems, which may cause device access
timeouts.
Per PCIe r3.0, sec 2.2.9, "Completion headers must supply the same values
for the Attribute as were supplied in the header of the corresponding
Request, except as explicitly allowed when IDO is used."
Instead of copying the Attributes from the Request to the Completion, the
T5 always generates Completions with zero Attributes. The receiver of a
Completion whose Attributes don't match the Request may accept it (which
itself seems non-compliant based on sec 2.3.2), or it may handle it as a
Malformed TLP or an Unexpected Completion, which will probably lead to a
device access timeout.
Work around this by disabling "Relaxed Ordering" and "No Snoop" in the Root
Port so it always generate Requests with zero Attributes.
This does affect all other devices which are downstream of that Root Port,
but these are performance optimizations that should not make a functional
difference.
Note that Configuration Space accesses are never supposed to have TLP
Attributes, so we're safe waiting till after any Configuration Space
accesses to do the Root Port "fixup".
Based on original work by Casey Leedom <leedom@chelsio.com>
[bhelgaas: changelog, comments, rename to pci_find_pcie_root_port(), rework
to use pci_upstream_bridge() and check for Root Port device type, edit
diagnostics to clarify intent and devices affected]
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
added PCI_DEV_FLAGS_VPD_REF_F0. Previously, we set the flag on every
non-zero function of quirked devices. If a function turned out to be
different from function 0, i.e., it had a different class, vendor ID, or
device ID, the flag remained set but we didn't make VPD accessible at all.
Flip this around so we only set PCI_DEV_FLAGS_VPD_REF_F0 for functions that
are identical to function 0, and allow regular VPD access for any other
functions.
[bhelgaas: changelog, stable tag]
Fixes: 932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
Acked-by: Mark Rustad <mark.d.rustad@intel.com>
CC: stable@vger.kernel.org
MSI is broken on SiS 761 chipset at least on PC Chips A31G board. No
interrupts are delivered once MSI is enabled for a device. This causes
hang on X11 start with a nVidia card installed (with nouveau driver).
Disable MSI completely for this chipset.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
On multi-function JMicron SATA/PATA/AHCI devices, the PATA controller at
function 1 doesn't work if it is powered on before the SATA controller at
function 0. The result is that PATA doesn't work after resume, and we
print messages like this:
pata_jmicron 0000:02:00.1: Refused to change power state, currently in D3
irq 17: nobody cared (try booting with the "irqpoll" option)
Async resume was introduced in v3.15 by 76569faa62 ("PM / sleep:
Asynchronous threads for resume_noirq"). Prior to that, we powered on
the functions in order, so this problem shouldn't happen.
e6b7e41cdd ("ata: Disabling the async PM for JMicron chip 363/361")
solved the problem for JMicron 361 and 363 devices. With async suspend
disabled, we always power on function 0 before function 1.
Barto then reported the same problem with a JMicron 368 (see comment #57 in
the bugzilla).
Rather than extending the blacklist piecemeal, disable async suspend for
all JMicron multi-function SATA/PATA/AHCI devices.
This quirk could stay in the ahci and pata_jmicron drivers, but it's likely
the problem will occur even if pata_jmicron isn't loaded until after the
suspend/resume. Making it a PCI quirk ensures that we'll preserve the
power-on order even if the drivers aren't loaded.
[bhelgaas: changelog, limit to multi-function, limit to IDE/ATA]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81551
Reported-and-tested-by: Barto <mister.freeman@laposte.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.15+
Firmware typically configures the PCIe fabric with a consistent Max Payload
Size setting based on the devices present at boot. A hot-added device
typically has the power-on default MPS setting (128 bytes), which may not
match the fabric.
The previous Linux default, in the absence of any "pci=pcie_bus_*" options,
was PCIE_BUS_TUNE_OFF, in which we never touch MPS, even for hot-added
devices.
Add a new default setting, PCIE_BUS_DEFAULT, in which we make sure every
device's MPS setting matches the upstream bridge. This makes it more
likely that a hot-added device will work in a system with optimized MPS
configuration.
Note that if we hot-add a device that only supports 128-byte MPS, it still
likely won't work because we don't reconfigure the rest of the fabric.
Booting with "pci=pcie_bus_peer2peer" is a workaround for this because it
sets MPS to 128 for everything.
[bhelgaas: changelog, new default, rework for pci_configure_device() path]
Tested-by: Keith Busch <keith.busch@intel.com>
Tested-by: Jordan Hargrave <jharg93@gmail.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
* pci/hotplug:
PCI: pciehp: Remove ignored MRL sensor interrupt events
PCI: pciehp: Remove unused interrupt events
PCI: pciehp: Handle invalid data when reading from non-existent devices
PCI: Hold pci_slot_mutex while searching bus->slots list
PCI: Protect pci_bus->slots with pci_slot_mutex, not pci_bus_sem
PCI: pciehp: Simplify pcie_poll_cmd()
PCI: Use "slot" and "pci_slot" for struct hotplug_slot and struct pci_slot
* pci/iommu:
PCI: Remove pci_ats_enabled()
PCI: Stop caching ATS Invalidate Queue Depth
PCI: Move ATS declarations to linux/pci.h so they're all together
PCI: Clean up ATS error handling
PCI: Use pci_physfn() rather than looking up physfn by hand
PCI: Inline the ATS setup code into pci_ats_init()
PCI: Rationalize pci_ats_queue_depth() error checking
PCI: Reduce size of ATS structure elements
PCI: Embed ATS info directly into struct pci_dev
PCI: Allocate ATS struct during enumeration
iommu/vt-d: Cache PCI ATS state and Invalidate Queue Depth
* pci/irq:
PCI: Kill off set_irq_flags() usage
* pci/virtualization:
PCI: Add ACS quirks for Intel I219-LM/V
Thomas Gleixner
Bjorn Helgaas
Alexey Kardashevskiy
Noa Osherovich
Linus Torvalds
Herbert Xu
Jon Derrick
Ananth Jasty
Xavier Gnata
Andreas Noever
Maik Broemme
Edward Cree
Alex Williamson
Chris Blake
Aaron Sierra
Jacek Lawrynowicz
Lukas Wunner
Heikki Krogerus
Babu Moger
Manish Jaggi
Tim Sander
Simon Horman
Jason S. McMullan
Daniel Vetter
Ville Syrjälä
Hariprasad Shenai
Ondrej Zary
Zhang Rui
Keith Busch