wl12xx is a driver for TI wl1251 802.11 chipset designed for embedded
devices, supporting both SDIO and SPI busses. Currently the driver
supports only SPI. Adding support 1253 (the 5 GHz version) should be
relatively easy. More information here:
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?contentId=4711&navigationId=12494&templateId=6123
(Collapsed original sequence of pre-merge patches into single commit for
initial merge. -- JWL)
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a doc-only patch which I hope will reduce the number of
spi_master controller driver patches starting out with a common
implementation bug.
(As in: almost every spi_master driver I see starts out with its
version of this bug. Sigh.)
It just re-emphasizes that the setup() method may be called for one
device while a transfer is active on another ... which means that most
driver implementations shouldn't touch any registers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Noises can be introduced when LCD signals are being driven, some platforms
provide a signal to assist the synchronization of this sampling procedure.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some SPI controllers have restrictions on DMAable buffers alignemt.
Currently if the buffer supplied by protocol driver is not properly
aligned, the controller silently performs transfer in PIO mode. Addition
of dma_alignment field to spi_master allows protocol drivers to perform
proper alignment.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change spi-gpio so that it is possible to drive SPI communications over
GPIO without the need for a chipselect signal.
This is useful in very small setups where there's only one slave device
on the bus.
This patch does not affect existing setups.
I use this for a tiny communication channel between an embedded device and
a microcontroller. There are not enough GPIOs available for chipselect
and it's not needed anyway in this case.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Define new setup() hook to export the accessor
- Implement accessor methods
Moves some error checking out of the sysfs interface code into the layer
below it, which is now shared by both sysfs and memory access code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[randy.dunlap@oracle.com: don't use bus_id]
[dtor@mail.ru: locking and other fixups]
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds more documentation of the lowlevel API to avoid future bugs.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In certain cases it is required to perform board specific actions
before activating libertas G-SPI interface. These actions may include
power up of the chip, GPIOs setup, proper pin-strapping and SPI
controller config.
This patch adds ability to call board specific setup/teardown methods
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
fix the following 'make headers_check' warning:
usr/include/linux/spi/spidev.h:83: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Add initial support for libertas devices using a GSPI interface. This has
been tested with the 8686.
GSPI is intended to be used on embedded systems. Board-specific parameters are
required (see libertas_spi.h).
Thanks to everyone who took a look at the earlier versions of the patch.
Signed-off-by: Colin McCabe <colin@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
Generalize the old at91rm9200 "bootstrap" bitbanging SPI master driver as
"spi_gpio", so it works with arbitrary GPIOs and can be configured through
platform_data. Such SPI masters support:
- any number of bus instances (bus_num is the platform_device.id)
- any number of chipselects (one GPIO per spi_device)
- all four SPI_MODE values, and SPI_CS_HIGH
- i/o word sizes from 1 to 32 bits;
- devices configured as with any other spi_master controller
When configured using platform_data, this provides relatively low clock
rates. On platforms that support inlined GPIO calls, significantly
improved transfer speeds are also possible with a semi-custom driver.
(It's still painful when accessing flash memory, but less so.)
Sanity checked by using this version to replace both native controllers on
a board with six different SPI slaves, relying on three different
SPI_MODE_* values and both SPI_CS_HIGH settings for correct operation.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Magnus Damm <damm@igel.co.jp>
Tested-by: Magnus Damm <damm@igel.co.jp>
Cc: Torgil Svensson <torgil.svensson@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include header files as used/needed:
In file included from drivers/leds/leds-dac124s085.c:16:
include/linux/spi/spi.h:66: error: field 'dev' has incomplete type
include/linux/spi/spi.h: In function 'to_spi_device':
include/linux/spi/spi.h💯 warning: type defaults to 'int' in declaration of '__mptr'
...
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The support is implemented via platform data accessors, new module
(of_mmc_spi) will be created automatically when the driver compiles
on OpenFirmware platforms. Link-time dependency will load the module
automatically.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fix compile error below:
LD drivers/spi/built-in.o
CC [M] drivers/spi/spi_gpio.o
In file included from drivers/spi/spi_gpio.c:26:
include/linux/spi/spi_bitbang.h:23: error: field `work' has incomplete type
make[2]: *** [drivers/spi/spi_gpio.o] Error 1
make[1]: *** [drivers/spi] Error 2
make: *** [drivers] Error 2
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support to orion_spi for the 88F6183 ARM SoC by adding code to work
around a 6183-specific erratum.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is not generic enough, added here for backward compatibility.
And make this an individual commit so future revert will be a bit
easier.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The driver is based on different source files including corgi_ssp.c,
corgi_lcd.c and corgi_bl.c, previously authored by Richard Purdie
and many others.
The LCD and Backlight device actually share the same SPI device, so
they are made into this single driver.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The GPIO connected to ADS7846 nPENIRQ signal is usually used to get
the pendown state as well. Introduce a .gpio_pendown, and use this
to decide the pendown state if .get_pendown_state is NULL.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds an SPI driver for the SPI controller found in various Marvell
Orion ARM SoCs. It currently supports only one slave, which must use SPI
mode 0.
[dbrownell@users.sourceforge.net: cleanups, meet specs, pass "sparse"]
Signed-off-by: Shadi Ammouri <shadi@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
spi_new_device() allocates and registers an spi device all in one swoop.
If the driver needs to add extra data to the spi_device before it is
registered, then this causes problems. This is needed for OF device
tree support so that the SPI device tree helper can add a pointer to
the device node after the device is allocated, but before the device
is registered. OF aware SPI devices can then retrieve data out of the
device node to populate a platform data structure.
This patch splits the allocation and registration portions of code out
of spi_new_device() and creates two new functions; spi_alloc_device()
and spi_register_device(). spi_new_device() is modified to use the new
functions for allocation and registration. None of the existing users
of spi_new_device() should be affected by this change.
Drivers using the new API can forego the use of spi_board_info
structure to describe the device layout and populate data into the
spi_device structure directly.
This change is in preparation for adding an OF device tree parser to
generate spi_devices based on data in the device tree.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Teach the mcp23s08 driver about a curious feature of these chips: up to
four of them can share the same chipselect, with the SPI signals wired in
parallel, by matching two bits in the first protocol byte against two
address lines on the chip.
This is handled by three software changes:
* Platform data now holds an array of per-chip structs, not
just one chip's address and pullup configuration.
* Probe() and remove() now use another level of structure,
wrapping an instance of the original structure for each
mcp23s08 chip sharing that chipselect.
* The HAEN bit is set, so that the hardware address bits can no
longer be ignored (boot firmware may not have enabled them).
The "one struct per chip" preserves the guts of the current code,
but platform_data will need minor changes.
OLD:
/* incorrect "slave" ID may not have mattered */
.slave = 3,
.pullups = BIT(3) | BIT(1) | BIT(0),
NEW:
/* slave address _must_ match chip's wiring */
.chip[3] = {
.is_present = true,
.pullups = BIT(3) | BIT(1) | BIT(0),
},
There's no change in how things _behave_ for spi_device nodes with a
single mcp23s08 chip. New multi-chip configurations assign GPIOs in
sequence, without holes. The spi_device just resembles a bigger
controller, but internally it has multiple gpio_chip instances.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support the Dallas/Maxim DS1305 and DS1306 RTC chips. These use SPI, and
support alarms, NVRAM, and a trickle charger for use when their backup
power supply is a supercap or rechargeable cell.
This basic driver doesn't yet support suspend/resume or wakealarms.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, 'modalias' in the spi_device structure is a 'const char *'.
The spi_new_device() function fills in the modalias value from a passed in
spi_board_info data block. Since it is a pointer copy, the new spi_device
remains dependent on the spi_board_info structure after the new spi_device
is registered (no other fields in spi_device directly depend on the
spi_board_info structure; all of the other data is copied).
This causes a problem when dynamically propulating the list of attached
SPI devices. For example, in arch/powerpc, the list of SPI devices can be
populated from data in the device tree. With the current code, the device
tree adapter must kmalloc() a new spi_board_info structure for each new
SPI device it finds in the device tree, and there is no simple mechanism
in place for keeping track of these allocations.
This patch changes modalias from a 'const char *' to a fixed char array.
By copying the modalias string instead of referencing it, the dependency
on the spi_board_info structure is eliminated and an outside caller does
not need to maintain a separate spi_board_info allocation for each device.
If searched through the code to the best of my ability for any references
to modalias which may be affected by this change and haven't found
anything. It has been tested with the lite5200b platform in arch/powerpc.
[dbrownell@users.sourceforge.net: cope with linux-next changes: KOBJ_NAME_LEN obliterated, etc]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (79 commits)
arm: bus_id -> dev_name() and dev_set_name() conversions
sparc64: fix up bus_id changes in sparc core code
3c59x: handle pci_name() being const
MTD: handle pci_name() being const
HP iLO driver
sysdev: Convert the x86 mce tolerant sysdev attribute to generic attribute
sysdev: Add utility functions for simple int/ulong variable sysdev attributes
sysdev: Pass the attribute to the low level sysdev show/store function
driver core: Suppress sysfs warnings for device_rename().
kobject: Transmit return value of call_usermodehelper() to caller
sysfs-rules.txt: reword API stability statement
debugfs: Implement debugfs_remove_recursive()
HOWTO: change email addresses of James in HOWTO
always enable FW_LOADER unless EMBEDDED=y
uio-howto.tmpl: use unique output names
uio-howto.tmpl: use standard copyright/legal markings
sysfs: don't call notify_change
sysdev: fix debugging statements in registration code.
kobject: should use kobject_put() in kset-example
kobject: reorder kobject to save space on 64 bit builds
...
Maxim's MAX7301 is an SPI GPIO expander with 28 GPIOs. Note: MAX7301's
interrupt feature is not supported yet.
[akpm@linux-foundation.org: coding-style fixes]
[g.liakhovetski@pengutronix.de: Fix inaccuracies in comments, check spi_setup()
return code, mask off high byte in max7301_read()]
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kobjects do not have a limit in name size since a while, so stop
pretending that they do.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds new platform data variable "caps", so platforms
could pass theirs capabilities into MMC core (for example, platforms
without interrupt on the CD line will most probably want to pass
MMC_CAP_NEEDS_POLL).
New platform get_cd() callback provided to optimize polling.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Since mmc_spi.h uses irqreturn_t type, it should include appropriate
header, otherwise build will break if users didn't include it (some of
them do not use interrupts).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This updates the ads7846 driver to handle external vREF (required
on boards using ads7843 chips) without module parameters, and also
removes a needless variable with its associated bogus gcc warning.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Basic driver for 8-bit SPI based MCP23S08 GPIO expander, without support for
IRQs or the shared chipselect mechanism.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'linus' of master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa: (264 commits)
[ALSA] version 1.0.15
[ALSA] Fix thinko in cs4231 mce down check
[ALSA] sun-cs4231: improved waiting after MCE down
[ALSA] sun-cs4231: use cs4231-regs.h
[ALSA] This simplifies and fixes waiting loops of the mce_down()
[ALSA] This patch adds support for a wavetable chip on
[ALSA] This patch removes open_mutex from the ad1848-lib as
[ALSA] fix bootup crash in snd_gus_interrupt()
[ALSA] hda-codec - Fix SKU ID function for realtek codecs
[ALSA] Support ASUS P701 eeepc [0x1043 0x82a1] support
[ALSA] hda-codec - Add array terminator for dmic in STAC codec
[ALSA] hdsp - Fix zero division
[ALSA] usb-audio - Fix double comment
[ALSA] hda-codec - Fix STAC922x volume knob control
[ALSA] Changed Jaroslav Kysela's e-mail from perex@suse.cz to perex@perex.cz
[ALSA] hda-codec - Fix for Fujitsu Lifebook C1410
[ALSA] mpu-401: remove MPU401_INFO_UART_ONLY flag
[ALSA] mpu-401: do not require an ACK byte for the ENTER_UART command
[ALSA] via82xx - Add DXS quirk for Shuttle AK31v2
[ALSA] hda-codec - Fix input_mux numbers for vaio stac92xx
...
Make the SPI framework and drivers stop using class_device. Update docs
accordingly ... highlighting just which sysfs paths should be
"safe"/stable.
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for the AT73C213 DAC using the misc Atmel SSC driver in
I2S mode. The driver also requires a SPI to setup the registers and control
volume.
It has been tested with an AT32AP7000 on the ATSTK1000 development board. The
driver should also work with any Atmel device with an SSC module supported by
the Atmel SSC driver (atmel-ssc).
The atmel-ssc driver is just submitted to the Linux kernel. Please see mail
thread http://lkml.org/lkml/2007/7/16/32
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This is the latest version of the MMC-over-SPI support. It works
on 2.6.23-rc2 plus git-mmc (from rc1-mm2), along with the preceding
patches which teach the rest of the MMC stack about SPI.
The main issue of note is that sometimes cards need to be power cycled
to recover after certain faults. Also, it may sometimes be necessary
to disable CRCs. ("modprobe mmc_core use_spi_crc=n")
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: mikael.starvik@axis.com,
Cc: Hans-Peter Nilsson <hp@axis.com>
Cc: Jan Nikitenko <jan.nikitenko@gmail.com>
Cc: Mike Lavender <mike@steroidmicros.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This adds kerneldoc to the SPI framework. The "spi_driver" and
"spi_board_info" structs were previously not described.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The spidev driver doesn't currently expose all SPI communications modes to
userspace. This passes them all through to the driver.
Two of them are potentially troublesome, in the sense that they could cause
hardware conflicts on shared busses. It might be appropriate to add some
privilege checks for for those modes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Loopback mode is supported by various controllers. This mode can be
useful for testing, especially in conjunction with spidev driver.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pendown status from the PENIRQ pin is currently read only at the beginning
of a sample set. If the pen is lifted just after sampling has began then
sampled values become wrong.
This patch adds an optional platform penirq_recheck_delay attribute. If
non-zero, samples are only reported to the input subsystem if PENIRQ is
still active that long after the samples taken.
Signed-off-by: Semih Hazar <semih.hazar@indefia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The ads7846 driver has support for filtering, but when the chip gets
deselected between samples this causes noise. This patch adds support
for an optional settling delay time, so that two consecutive samples
will be taken with the specified delay time apart. This ensures that
the chip won't be deselected, so the noise won't appear.
Filtering can still be done, but will have less work to do since each
time a new sample is taken the same delay applies.
Signed-off-by: Semih Hazar <semih.hazar@indefia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add support for the Infineon TLE62x0 series of low-side driver chips, such
as the TLE6220 or TLE6230. These can be viewed as output GPIOs specialized
for power switching applications. The driver provides a userspace
interface to those GPIOs, and to the switch status they provide.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller
Kalle Valo
David Brownell
Dmitry Torokhov
Eric Miao
Mike Rapoport
Michael Buesch
Michael Hennerich
Jaswinder Singh Rajput
Colin McCabe
Linus Torvalds
Frederik Schwarzer
Randy Dunlap
Anton Vorontsov
Fernando Luis Vazquez Cao
Lennert Buytenhek
Eric Miao
Shadi Ammouri
Grant Likely
David Brownell
Juergen Beisert
Kay Sievers
Linus Torvalds
Tony Jones
Hans-Christian Egtvedt
Semih Hazar
Ben Dooks