This adds the missing pins for the PWM controllers found in Amlogic
Meson8 SoCs. This includes the pins for PWM_A, PWM_B, PWM_C, PWM_D,
PWM_E and PWM_F controllers.
There is an additional PWM function with the name PWM_VS in the vendor
kernel sources which seems to be used for external video input. Thus
it's not part of this change as the IP block behind the pwm-meson driver
is not responsible for these pins.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit
The script “checkpatch.pl” pointed information out like the following.
Comparison to NULL could be written …
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A single character (line break) should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The script "checkpatch.pl" pointed information out like the following.
CHECK: spaces preferred around that '+' (ctx:VxV)
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The script "checkpatch.pl" pointed information out like the following.
WARNING: quoted string split across lines
Thus fix the affected source code place.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit
The script “checkpatch.pl” pointed information out like the following.
Comparison to NULL could be written !…
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Strings which did not contain data format specifications should be put
into a sequence. Thus use the corresponding function "seq_puts".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Updating the point of contact for AMD GPIO driver.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Cc: Ken Xue <Ken.Xue@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A single character (line break) should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Armada 37xx SoCs can handle interrupt through GPIO. However it can
only manage the edge ones.
The way the interrupt are managed is classical so we can use the generic
interrupt chip model.
The only unusual "feature" is that many interrupts are connected to the
parent interrupt controller. But we do not take advantage of this and use
the chained irq with all of them.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin controller on ZTE ZX platforms is kinda of hybrid. It consists
of a main controller and an auxiliary one. For example, on ZX296718 SoC,
the main controller is TOP_PMM and the auxiliary one is AON_IOCFG. Both
controllers work together to control pin multiplexing and configuration.
For most of pins, the pinmux function is controlled by main controller
only, and this type of pins are meant by term 'TOP pins'. For other
pins, the pinmux is controlled by both main and auxiliary controllers,
as the available multiplexing functions for the pin spread in both
controllers. This type of pins are called 'AON pins'. Though pinmux
implementation is quite different, pinconf is same for both types of
pins. Both are controlled by auxiliary controller, i.e. AON_IOCFG on
ZX296718.
The patch adds the ZTE ZX core pinctrl driver to support this hybrid
pin controller as well as ZX296718 SoC specific pin data.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 8c58f1a7a4.
It turns out that applying these generic properties was
premature: the properties used in the driver using this
are of unclear electrical nature and the subject need to
be discussed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make sure dmi_system_id tables are NULL terminated.
Fixes: 7036502783 ("pinctrl: cherryview: Add a quirk to make Acer
Chromebook keyboard work again")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Renesas RZ/G1E (R8A7745) is pin compatible with R-Car E2 (R8A7794),
however it doesn't have several automotive specific peripherals.
Annotate all the items that only exist on the R-Car SoCs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
[geert: Drop annotations, as they are implied by pin groups/functions]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The R8A7794 PFC driver was apparently based on the preliminary revisions
of the user's manual which had some signals and MOD_SEL register fields
described which the recent manual changed to reserved. Of course, these
signals haven't ever been really used, which makes removing them
painless.
While at it, make the large *enum* look better by starting a new line
each time a new row in the IPSR and MOD_SEL register field tables is
started.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The ATA_AVTP_* signals are documented as reserved in the recent R-Car E2
user's manual (the only remaining mention is in the table 5.2 and I believe
it's a simple overlook). Remove the AVB_AVTP_* pinmux groups -- we will
remove the signals themselves in the next patch, along with the other now
reserved bits...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The R8A7794 PFC driver was apparently based on the preliminary revisions
of the user's manual which called I2C5 device IIC0 and IIC0 device IIC1.
Luckily, these signals haven't been used for any functions/groups so
far, so the renaming should be painless..
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Renesas RZ/G1M (R8A7743) is pin compatible with R-Car M2-W/N (R8A7791/3),
however it doesn't have several automotive specific peripherals. Annotate
all the items that only exist on the R-Car SoCs and only supply the pin
groups/functions existing on a given SoC...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
[geert: Drop annotations, as they are implied by pin groups/functions]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car Gen3 is using SSI_{WS,SCK}349 instead of SSI_{WS,SCK}34.
But, current code is based on old datasheet which had typo.
This patch fixes this typo.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car Gen3 is using SSI_{WS,SCK}349 instead of SSI_{WS,SCK}34.
But, current code is based on old datasheet which had typo.
This patch fixes this typo.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car Gen3 is using SSI_{WS,SCK}349 instead of SSI_{WS,SCK}34.
But, current code is based on old datasheet which had typo.
This patch fixes this typo.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
of_device_id::data is an opaque pointer. No explicit cast is needed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Based on Rev 0.50 or later R-Car Gen3 datasheet.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Group the AVB pins into similar groups as found in other sh-pfc drivers.
The pins can not be muxed between functions other than AVB, but their
drive strengths can be controlled.
The group avb_mdc containing ADV_MDC and ADV_MDIO is called avb_mdio on
R-Car Gen2 SoCs. In pfc-r8a7796 the avb_mdc group already existed and
is in use in DT. Therefore add the ADV_MDIO pin to the existing group
instead of renaming it.
Based on commit b25719eb93 ("pinctrl: sh-pfc: r8a7795: Add group
for AVB MDIO and MII pins").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The R8A7791 PFC driver was apparently based on the preliminary revisions
of the user's manual, which called all the I2C signals {SCL|SDA}<n> and
MOD_SEL register fields SEL_IIC<n> without making a difference between
two types of the I2C controllers used. The recent manual calls the
signals {I2C|IIC}<n>_{SCL|SDA> and the MOD_SEL fields SEL_{I2C|IIC}<n>
finally making this difference. Follow the suit...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Core changes:
- Add bi-directional and output-enable pin configurations to
the generic bindings and generic pin controlling core.
New drivers or subdrivers:
- Armada 37xx SoC pin controller and GPIO support.
- Axis ARTPEC-6 SoC pin controller support.
- AllWinner A64 R_PIO controller support, and opening up the
AllWinner sunxi driver for ARM64 use.
- Rockchip RK3328 support.
- Renesas R-Car H3 ES2.0 support.
- STM32F469 support in the STM32 driver.
- Aspeed G4 and G5 pin controller support.
Improvements:
- A whole slew of realtime improvements to drivers implementing
irqchips: BCM, AMD, SiRF, sunxi, rockchip.
- Switch meson driver to get the GPIO ranges from the device
tree.
- Input schmitt trigger support on the Rockchip driver.
- Enable the sunxi (AllWinner) driver to also be used on ARM64
silicon.
- Name the Qualcomm QDF2xxx GPIO lines.
- Support GMMR GPIO regions on the Intel Cherryview. This
fixes a serialization problem on these platforms.
- Pad retention support for the Samsung Exynos 5433.
- Handle suspend-to-ram in the AT91-pio4 driver.
- Pin configuration support in the Aspeed driver.
Cleanups:
- The final name of Rockchip RK1108 was RV1108 so rename the
driver and variables to stay consistent.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZCG0aAAoJEEEQszewGV1zBpcP/37y0m2ZFIqVJrqlPKVeZbRa
aYwsbY3l9OGeocLXSRWaqLJkwJ+WaG8ascoXHLMgk4jFC2CutwUea0fzhy9Li2VO
Sqd/BN9iNd/g2lTf8o37NM5qYF5IvStZu12DzFPRFpec6pEiYOHVmRiSlIK5lREG
v/NGNAIzLPH59jRHA17sLT1lkHmiT43S4Gm38nvpar8vfO+2UkAwGVPQPC8dGuL9
gydMLLtx3d1SzWqicbMSICa/F7kjWz5I4jL6KM7ohVGXgDn8tdZk+7rERfBD9qoR
eDNPZvXajaC6y3S3h6Ynv094X30w3VA0xtj9kPVhJsS1yUlVli5GlC3WHPArwrRQ
sXx29UsdTmAjzHHns4OZfxKnEVvHbXtW1XmX+ks248f/k8hCVWpQA9ZENvVHjLvu
NkDwXOmTWOxjutDveZqm7RM6z+99+lRgzLgwB3GMENIUC8ohH79W/R9GYHvrqOZI
hWX+G/q3nnnW3cIPc15rN2MC3fkjE2mdFC0N+/kDlKtzPabCS8U6JZsfQDulX5m1
I2xF2DY+1WWCy1mMDpyTdYNDlkOGU8j/N5MXx9z1629m+vjg0KZo35+mGwJh5mA1
gQ6rI3DdhS5qVK2Gj/joYkwQ1cKpdEtljlpI9A+WdXx1eO7RKVK1m1fxbd8c47L/
I0qdXsL66ZtiKDOIDPau
=BCaA
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.12 cycle.
The extra week before the merge window actually resulted in some of
the type of fixes that usually arrive after the merge window already
starting to trickle in from eager developers using -next, I'm
impressed.
I have recruited a Samsung subsubsystem maintainer (Krzysztof) to deal
with the onset of Samsung patches. It works great.
Apart from that it is a boring round, just incremental updates and
fixes all over the place, no serious core changes or anything exciting
like that. The most pleasing to see is Julia Cartwrights work to audit
the irqchip-providing drivers for realtime locking compliance. It's
one of those "I should really get around to looking into that" things
that have been on my TODO list since forever.
Summary:
Core changes:
- add bi-directional and output-enable pin configurations to the
generic bindings and generic pin controlling core.
New drivers or subdrivers:
- Armada 37xx SoC pin controller and GPIO support.
- Axis ARTPEC-6 SoC pin controller support.
- AllWinner A64 R_PIO controller support, and opening up the
AllWinner sunxi driver for ARM64 use.
- Rockchip RK3328 support.
- Renesas R-Car H3 ES2.0 support.
- STM32F469 support in the STM32 driver.
- Aspeed G4 and G5 pin controller support.
Improvements:
- a whole slew of realtime improvements to drivers implementing
irqchips: BCM, AMD, SiRF, sunxi, rockchip.
- switch meson driver to get the GPIO ranges from the device tree.
- input schmitt trigger support on the Rockchip driver.
- enable the sunxi (AllWinner) driver to also be used on ARM64
silicon.
- name the Qualcomm QDF2xxx GPIO lines.
- support GMMR GPIO regions on the Intel Cherryview. This fixes a
serialization problem on these platforms.
- pad retention support for the Samsung Exynos 5433.
- handle suspend-to-ram in the AT91-pio4 driver.
- pin configuration support in the Aspeed driver.
Cleanups:
- the final name of Rockchip RK1108 was RV1108 so rename the driver
and variables to stay consistent"
* tag 'pinctrl-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (80 commits)
pinctrl: mediatek: Add missing pinctrl bindings for mt7623
pinctrl: artpec6: Fix return value check in artpec6_pmx_probe()
pinctrl: artpec6: Remove .owner field for driver
pinctrl: tegra: xusb: Silence sparse warnings
ARM: at91/at91-pinctrl documentation: fix spelling mistake: "contoller" -> "controller"
pinctrl: make artpec6 explicitly non-modular
pinctrl: aspeed: g5: Add pinconf support
pinctrl: aspeed: g4: Add pinconf support
pinctrl: aspeed: Add core pinconf support
pinctrl: aspeed: Document pinconf in devicetree bindings
pinctrl: Add st,stm32f469-pinctrl compatible to stm32-pinctrl
pinctrl: stm32: Add STM32F469 MCU support
Documentation: dt: Remove ngpios from stm32-pinctrl binding
pinctrl: stm32: replace device_initcall() with arch_initcall()
pinctrl: stm32: add possibility to use gpio-ranges to declare bank range
pinctrl: armada-37xx: Add gpio support
pinctrl: armada-37xx: Add pin controller support for Armada 37xx
pinctrl: dt-bindings: Add documentation for Armada 37xx pin controllers
pinctrl: core: Make pinctrl_init_controller() static
pinctrl: generic: Add bi-directional and output-enable
...
In case of error, the function pinctrl_register() returns
ERR_PTR() not NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 53d2a715c2 ("phy: Add Tegra XUSB pad controller support") added
a new driver for the XUSB pad controller that implements a more flexible
devicetree binding. In order to preserve backwards compatibility the old
driver can be probed if the obsolete bindings are detected.
In order to hide the legacy code, these prototypes were defined in a
header private to the new driver. This has the disadvantage of making
the sparse code checker complain about the missing declarations when
compiling the old driver and suggesting to make the functions static.
Avoid these sparse warnings by adding local prototype declarations into
the compatibility driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/Kconfig:config PINCTRL_ARTPEC6
drivers/pinctrl/Kconfig: bool "Axis ARTPEC-6 pin controller driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Lars Persson <lars.persson@axis.com>
Cc: Niklas Cassel <niklas.cassel@axis.com>
Cc: linux-arm-kernel@axis.com
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Testing for pinctrl-aspeed-g5 was performed on an AST2500EVB system,
using the strategy outlined in the commit message for the change to the
Aspeed pinctrl core.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Testing for pinctrl-aspeed-g4 was performed on an OpenPOWER Palmetto
system, using the strategy outlined in the commit message for the
change to the Aspeed pinctrl core.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Several pinconf parameters have a fairly straight-forward mapping onto
the Aspeed pin controller. These include management of pull-down bias,
drive-strength, and some debounce configuration.
Pin biasing largely is managed on a per-GPIO-bank basis, aside from the
ADC and RMII/RGMII pins. As the bias configuration for each pin in a
bank maps onto a single per-bank bit, configuration tables will be
introduced to describe the ranges of pins and the supported pinconf
parameter. The use of tables also helps with the sparse support of
pinconf properties, and the fact that not all GPIO banks support
biasing or drive-strength configuration.
Further, as the pin controller uses a consistent approach for bias and
drive strength configuration at the register level, a second table is
defined for looking up the the bit-state required to enable or query the
provided configuration.
Testing for pinctrl-aspeed-g4 was performed on an OpenPOWER Palmetto
system, and pinctrl-aspeed-g5 on an AST2500EVB as well as under QEMU.
The test method was to set the appropriate bits via devmem and verify
the result through the controller's pinconf-pins debugfs file. This
simultaneously validates the get() path and half of the set() path. The
remainder of the set() path was validated by configuring a handful of
pins via the devicetree with the supported pinconf properties and
verifying the appropriate registers were touched.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch which adds STM32F469 pinctrl and GPIO support, relies on the
generic STM32 pinctrl driver.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pinctrl has to be registered earlier. Mainly to register bank irqdomain
earlier as other devices could use interrupts from those irqdomain.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use device tree entries to declare gpio range. It will allow to use
no contiguous gpio bank and holes inside a bank.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO management is pretty simple and is part of the same IP than the pin
controller for the Armada 37xx SoCs. This patch adds the GPIO support to
the pinctrl-armada-37xx.c file, it also allows sharing common functions
between the gpiolib and the pinctrl drivers.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Armada 37xx SoC come with 2 pin controllers: one on the south
bridge (managing 28 pins) and one on the north bridge (managing 36 pins).
At the hardware level the controller configure the pins by group and not
pin by pin. This constraint is reflected in the design of the driver:
only the group related functions are implemented.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl_init_controller() is not used outside core.c, thus make it
static and prevent compiler to warn.
drivers/pinctrl/core.c:1943:21: warning: no previous prototype for ‘pinctrl_init_controller’ [-Wmissing-prototypes]
struct pinctrl_dev *pinctrl_init_controller(struct pinctrl_desc *pctldesc,
^~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add bi-directional and output-enable pin configuration properties.
bi-directional allows to specify when a pin shall operate in input and
output mode at the same time. This is particularly useful in platforms
where input and output buffers have to be manually enabled.
output-enable is just syntactic sugar to specify that a pin shall
operate in output mode, ignoring the provided argument.
This pairs with input-enable pin configuration option.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After commit 47c950d102 ("pinctrl: cherryview: Do not add all
southwest and north GPIOs to IRQ domain") the driver does not add all
GPIOs to the irqdomain. The reason for that is that those GPIOs cannot
generate IRQs at all, only GPEs (General Purpose Events). This causes
Linux virtual IRQ numbering to change.
However, it seems some CYAN Chromebooks, including Acer Chromebook
hardcodes these Linux IRQ numbers in the ACPI tables of the machine.
Since the numbering is different now, the IRQ meant for keyboard does
not match the Linux virtual IRQ number anymore making the keyboard
non-functional.
Work this around by adding special quirk just for these machines where
we add back all GPIOs to the irqdomain. Rest of the Cherryview/Braswell
based machines will not be affected by the change.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194945
Fixes: 47c950d102 ("pinctrl: cherryview: Do not add all southwest and north GPIOs to IRQ domain")
Reported-by: Adam S Levy <theadamlevy@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Three video input signals suffered from a search/replace failure in
some copied code.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
1. Add support for pad retention control through pinctrl drivers which
moves us forward to better runtime PM of pinctrl, clocks, power domains
and other devices.
2. Fix GPIO hogs by registering pinctrl before registering gpiolib.
3. Use devm-like interface.
-----BEGIN PGP SIGNATURE-----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=r4lP
-----END PGP SIGNATURE-----
Merge tag 'samsung-pinctrl-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/samsung into devel
Samsung pinctrl drivers update for v4.12:
1. Add support for pad retention control through pinctrl drivers which
moves us forward to better runtime PM of pinctrl, clocks, power domains
and other devices.
2. Fix GPIO hogs by registering pinctrl before registering gpiolib.
3. Use devm-like interface.
The commit 1259feddd0f8("pinctrl: samsung: Fix the width of
PINCFG_TYPE_DRV bitfields for Exynos5433") already fixed
the different width of PINCFG_TYPE_DRV from previous Exynos SoC.
However wrong merge conflict resolution was chosen in commit
7f36f5d11c ("Merge tag 'v4.10-rc6' into devel") effectively dropping
the changes for PINCFG_TYPE_DRV. Re-do them here.
The macro EXYNOS_PIN_BANK_EINTW is no longer used so remove it.
Fixes: 7f36f5d11c ("Merge tag 'v4.10-rc6' into devel")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When suspending to RAM, the power to the core is cut and the register
values are lost. Save and restore more registers than just IMR.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Correct the incorrect function name and description.
Fixes: a76edc89b1 ("pinctrl: core: Add generic pinctrl functions for managing groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl driver support for the Axis ARTPEC-6 SoC.
There are only some pins that actually have different
functions available, but all can control bias (pull-up/-down)
and drive strength.
Code originally written by Chris Paterson.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The NAND DQS pins are currently named nand_dqs_0 and nand_dqs_1.
However, they both seem to have the same function, just exposed on
different pins (unlike the ethernet TX pins for example, where there's
eth_txd0..3 - all of these can be active at the same time as they are
different data lines).
Rename the NAND DQS pins to nand_dqs_15 and nand_dqs_18 to reflect that
it's the same functionality just exposed on different pins (BOOT_15 and
BOOT_18).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The nand_groups table uses different names for the NAND DQS pins than
the GROUP() definition in meson8b_cbus_groups (nand_dqs_0 vs nand_dqs0).
This prevents using the NAND DQS pins in the devicetree.
Fix this by ensuring that the GROUP() definition and the
meson8b_cbus_groups use the same name for these pins.
Fixes: 0fefcb6876 ("pinctrl: Add support for Meson8b")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Recent pinctrl changes to allow dynamic allocation of pins exposed one
more issue with the pinctrl pins claimed early by the controller itself.
This caused a regression for IMX6 pinctrl hogs.
Before enabling the pin controller driver we need to wait until it has
been properly initialized, then claim the hogs, and only then enable it.
To fix the regression, split the code into pinctrl_claim_hogs() and
pinctrl_enable(). And then let's require that pinctrl_enable() is always
called by the pin controller driver when ready after calling
pinctrl_register_and_init().
Depends-on: 950b0d91dc ("pinctrl: core: Fix regression caused by delayed
work for hogs")
Fixes: df61b366af26 ("pinctrl: core: Use delayed work for hogs")
Fixes: e566fc11ea ("pinctrl: imx: use generic pinctrl helpers for
managing groups")
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Mika Penttilä <mika.penttila@nextfour.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Gary Bisson <gary.bisson@boundarydevices.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All R8A7794 manuals I have here (0.50 and 1.10) agree that the PFC driver
has ATAG0# and ATAWR0# signals in IPSR12 swapped -- fix this.
Fixes: 43c4436e2f ("pinctrl: sh-pfc: add R8A7794 PFC support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
- Add basic support for the Pin Function Controller on revision ES2.0
of the R-Car H3 SoC, which differs from ES1.x in many ways.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJY3h2vAAoJEEgEtLw/Ve77hCwP/0k48APKuK+OYbTqlLadouK/
/TfPiFG2r2qaoPoZiL3Afnh8rbYxKP4fh3iemoAclE6TuqV2K/OU7T31KT+0o3T9
enOQ0zjKgIyetyknBNSiWZ9rx/lQQ0H9ZUUlFkd3mc/BuUYach0tXt4UZL3zgQVs
GhUrYbW8tmNv5o+UlhRB6ht26BA3DKOC/m2DEmHDzEHCAjnIWI7wIimAuDTIIFIE
6q/E1Q/l/krJaY1GXKQQiSx+7jH6sPBR3YBupzzP4BlPpEf7evyNtQIHTiP2P2WM
a4hcqQi+1zdfZ50XUQxv4L1q28RRKoq3wyDWa4uW+MGLPbICzR5TfFJBgaT8Rb3+
jCL8b4ju7IR/WWc1vKLxSW2XVPyc2naeF4p4nFTCRcxbznSRbly0aHDnKh1YVGuU
SFHCtOCNsECSmEPtuCfElPiKcrcWQg9hLHaYY6mgTh5deSVjEqjSn0wD3+DW+pen
c1pmwFtrgQGFXJgjH3YI5gRJevAQxotzUdvCJ+mfRbz/EiuiZRD4wOvo24bs3SkH
LQPqbFJ93GnIu11EaeJD/uE4GmMSj9oO9c0bI1t3mJTuNzzV+9lOVaxhp5KgRExr
6YYlKuFZygtHCMUrI221+OZqAeSe7fcz/O4W3cjk2xJX898mZ+Ly1b7wqUC085GD
gfrm2MDgu4e27DOuvkl5
=fKYc
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.12-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.12 (take two)
- Add basic support for the Pin Function Controller on revision ES2.0
of the R-Car H3 SoC, which differs from ES1.x in many ways.
The IPSR field names in the comments have been fat-fingered in a couple
places -- fix those silly typos...
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
PINMUX_IPSR_MSEL() macro invocation for the TX2 signal has apparently wrong
1st argument -- most probably a result of cut&paste programming...
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The R8A7791 PFC driver was apparently based on the preliminary revisions
of the user's manual, which omitted the DVC_MUTE signal altogether in
the PFC section. The modern manual has the signal described, so just add
the necassary data to the driver...
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The R8A7791 PFC driver was apparently based on the preliminary revisions
of the user's manual, which omitted the HSCIF1 group E signals in the
IPSR4 register description. This would cause HSCIF1's probe to fail with
the messages like below:
sh-pfc e6060000.pfc: cannot locate data/mark enum_id for mark 1989
sh-sci e62c8000.serial: Error applying setting, reverse things back
sh-sci: probe of e62c8000.serial failed with error -22
Add the neceassary PINMUX_IPSR_MSEL() invocations for the HSCK1_E,
HCTS1#_E, and HRTS1#_E signals...
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pins, groups, and a function for SCIF_CLK on R-Car H3 ES2.0.
SCIF_CLK is the external clock source for the Baud Rate Generator for
External Clock (BRG) on (H)SCIF serial ports.
Extracted from a big patch in the BSP by Takeshi Kihara.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Add pins, groups, and functions for all SCIF serial ports on R-Car H3
ES2.0.
Extracted from a big patch in the BSP by Takeshi Kihara.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>
The Pin Function Controller module in the R-Car H3 ES2.0 differs from
ES1.x in many ways.
The goal is twofold:
1. Support both the ES1.x and ES2.0 SoC revisions in a single binary
for now,
2. Make it clear which code supports ES1.x, so it can easily be
identified and removed later, when production SoCs are deemed
ubiquitous.
Hence this patch:
1. Extracts the support for R-Car H3 ES1.x into a separate file, as
the differences are quite large,
2. Adds code for detecting the SoC revision at runtime using the new
soc_device_match() API, and selecting pinctrl tables for the actual
SoC revision,
3. Replaces the core register and bitfield definitions by their
counterparts for R-Car H3 ES2.0.
The addition of pins, groups, and functions for the various on-chip
devices is left to subsequent patches.
The R-Car H3 ES2.0 register and bitfield definitions were extracted from
a patch in the BSP by Takeshi Kihara.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>
When trying to add a gpio-hog, we enter a weird loop where the gpio-ranges
is needed when gpiochip_add_data() is called but in the current implementation
the ranges are added from the driver afterwards.
A simple solution is to rely on the DR gpio-ranges attribute and remove the
call to gpiochip_add_pin_range().
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix some inverted bit numbers in some pinctrl groups and add missing pins
and groups to be in pair with the GXBB pinctrl pins definition.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With real-time preemption, regmap functions cannot be used in the
implementation of irq_chip since they use spinlocks which may sleep.
Move the setting of the mux for IRQs to an irq_bus_sync_unlock handler
where we are allowed to sleep.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to avoid calling regmap functions from irq handlers, so the next
commit is going to move the call to rockchip_set_mux() into an
irq_bus_sync_unlock handler. But we can't return an error from there so
we still need to check the settings from rockchip_irq_set_type() and we
will use this new rockchip_verify_mux() function from there.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This lock is used from rockchip_irq_set_type() which is part of the
irq_chip implementation and thus must use raw_spinlock_t as documented
in Documentation/gpio/driver.txt.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
regmap_update_bits does its own locking and everything else accessed
here is a local variable so there is no need to lock around it.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fix some spelling typos found in printk.
[jkosina@suse.cz: drop arch/arm64/kernel/hibernate.c that was already
in place]
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use devm_gpiochip_add_data to simplify the error path in
samsung_gpiolib_register.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
If we request a GPIO hog, then gpiochip_add_data will attempt
to request some of its own GPIOs. The driver also uses
gpiochip_generic_request which means that for any GPIO request to
succeed the pinctrl needs to be registered. Currently however the
driver registers the GPIO and then the pinctrl meaning all GPIO hog
requests will fail, which then in turn causes the whole driver to fail
probe.
Fix this up by ensuring we register the pinctrl first. This
does require us to manually set the GPIO base for the
pinctrl. Fortunately the driver already assigns a fixed GPIO base, in
samsung_gpiolib_register, and uses the same calculation it does for
the pin_base. Meaning the two will always be the same and allowing us
to reuse the pinbase and avoid the issue.
Although currently there are no users of GPIO hogs in mainline
there are plenty of Samsung based boards that are widely used for
development purposes of other hardware. Indeed we hit this issue
whilst attaching some additional hardware to an Arndale system.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds support for retention control for Exynos5433 SoCs. Three
groups of pins has been defined for retention control: common shared group
for ALIVE, CPIF, eSE, FINGER, IMEM, NFC, PERIC, TOUCH pin banks and
separate control for FSYS and AUD pin banks, for which PMU retention
registers match whole banks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
When pin controller device is a part of power domain, there is no guarantee
that the power domain was not turned off and then on during boot process
before probing of the pin control driver. If it happened, then pin control
driver should ensure that pad retention is turned off during its probe call.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
On some Cherry Trail devices the ASL uses the GMMR GPIO to access
GPIOs so as to serialize MMIO accesses to GPIO registers with the
OS, because:
"Due to a silicon issue, a shared lock must be used to prevent concurrent
accesses across the 4 GPIO controllers.
See Intel Atom Z8000 Processor Series Specification Update (Rev. 005),
errata #CHT34, for further information."
This commit adds support for this opregion, this fixes a number of
ASL errors on my Ezpad mini3 tablet and makes the otg port device/host
muxing which is controlled in firmware on this model work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rockchip finally named the SOC as RV1108, so change it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[adapted rk1108 dtsi to keep bisectability]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the missing PINGROUP for GPIO70-99.
This fixes a crash that happens in pinctrl-msm, if any
of the GPIO70-99 are accessed.
Fixes: 5303f7827f ("pinctrl: qcom: ipq4019: set ngpios to correct value")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When using GPIO as IRQ source, the GPIO must be configured
in INPUT. Callbacks dedicated for this was missing in
pinctrl-st driver.
This fix the following kernel error when trying to lock a gpio
as IRQ:
[ 7.521095] gpio gpiochip7: (PIO11): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
[ 7.526018] gpio gpiochip7: (PIO11): unable to lock HW IRQ 6 for IRQ
[ 7.529405] genirq: Failed to request resources for 0-0053 (irq 81) on irqchip GPIO
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clearing the status bit on irq_unmask will discard any pending interrupt
that did arrive after the irq_ack, i.e. while the IRQ handler function
was executing.
Fixes: f365be0925 ("pinctrl: Add Qualcomm TLMM driver")
Cc: stable@vger.kernel.org
Cc: Stephen Boyd <sboyd@codeaurora.org>
Reported-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some pinctrls share memory regions, and devm_ioremap_resource does not
allow to share resources, in opposition to devm_ioremap.
This patch restores back usage of devm_ioremap function, but with proper
error handling and logging.
Fixes: baafaca ("pinctrl: samsung: Fix return value check in samsung_pinctrl_get_soc_data()")
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As the IODelay driver is a hardware feature of the DRA7xxx SoC
depend on that SoC and compile test.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently we are trying to enable/disable the clk of irq's gpio bank when
unmask/mask irq. But the kernel's "lazy disable approach" will skip masking
irq when the irq chip doesn't support irq_disable ops.
So we may hit this case:
irq_enable-> enable clk
irq_disable-> noop
irq_enable-> enable clk again
irq_disable-> noop
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At first these drivers were written as tristate, but the module
usecases are actually not tested. Make all of them boolean.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 3e030b0b4e ("pinctrl: uniphier: allow to have pinctrl
node under syscon node"), this driver has kept compatibility for the
old DT files. Several releases have passed since then, so remove
the obsoleted compatibles and clean up the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the missing PWM pins on Meson GXL SoCs, namely:
- PWM_A
- PWM_B
- PWM_C
- PWM_F (GPIOX_7 and GPIOCLK_1 can be selected as output)
- PWM_AO_A (GPIOAO_3 and GPIOAO_8 can be selected as output)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update the sh_pfc_soc_info pointer after calling the SoC-specific
initialization function, as it may have been updated to e.g. handle
different SoC revisions. This makes sure the correct subdriver name is
printed later.
Fixes: 0c151062f3 ("sh-pfc: Add support for SoC-specific initialization")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Somehow the QSPI and SCIF_CLK fragments were inserted at the wrong
positions. Restore sort order (alphabetically, per group).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The sunxi pinctrl driver currently implement an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sirf atlas7 pinctrl drivers currently implement an irq_chip for
handling interrupts; due to how irq_chip handling is done, it's
necessary for the irq_chip methods to be invoked from hardirq context,
even on a a real-time kernel. Because the spinlock_t type becomes a
"sleeping" spinlock w/ RT kernels, it is not suitable to be used with
irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The amd pinctrl drivers currently implement an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The bcm pinctrl drivers currently implement an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sysfs and debugfs entries for pin control drivers work better when
the individual pins are given real names, even if they are all just
"gpio0", "gpio1", etc.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To prevent external signal crosstalk, some pins need to
enable input schmitt, like i2c pins, 32k-input pin and so on.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allwinner pin controllers are also GPIO controllers.
Currently, if GPIOLIB is forgot to be chosen, the build of
pinctrl-sunxi.c will fail for lacking a lot of gpiochip_* functions.
Select GPIOLIB to ensure this driver can be built.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A64 has a R_PIO pin controller, similar to the one found on the H3 SoC.
Add support for the pins controlled by the R_PIO controller.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ARM64 Allwinner SoCs used to have every pinctrl driver selected in
ARCH_SUNXI. Change this to make their default value to (ARM64 &&
ARCH_SUNXI).
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Just fix spelling typos in comments.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Port D and port E GPIO loopback modes are commonly enabled via hardware
straps for use with front-panel buttons. When the BMC is powered
off or fails to boot, the front-panel buttons are directly connected to
the host chipset via the loopback to allow direct power-on and reset
control. Once the BMC has booted, the loopback mode must be disabled for
the BMC to take over control of host power-on and reset.
Disabling these loopback modes requires writing to the hardware strap
register which violates the current design of assuming the system
designer chose the strap settings for a specific reason and they should
be treated as read-only. Only the two bits of the strap register related
to these loopback modes are allowed to be written and comments have been
added to explain why.
Signed-off-by: Rick Altherr <raltherr@google.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Note, the iomux of following pins are special, need to
be recalculated specially.
- gpio2_b4
- gpio2_b7
- gpio2_c7
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some pins are special at a bank so that add
IOMUX_RECALCED type to indicate which iomux source
of the bank need to be recalculated. If the mux
recalculateed callback and IOMUX_RECALCED type
were set, recalculate the pins' iomux by using
mux recalculated data struct.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The local variable drvdata is not used in samsung_gpio_set_direction.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch changes pin names of AIO and XIRQ according to updated
specification.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The get_direction callback function allows gpiolib to know the current
direction (input vs output) for a given GPIO.
This is particularly useful on ACPI systems, where the GPIOs are
configured only by firmware (typically UEFI), so the only way to
know the initial values to query the hardware directly. Without
this function, gpiolib thinks that all GPIOs are configured for
input.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix typos and add the following to the scripts/spelling.txt:
overrided||overridden
Link: http://lkml.kernel.org/r/1481573103-11329-22-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core changes:
- Switch the generic pin config argument from 16 to 24 bits,
only use 8 bits for the configuration type. We might need to
encode more information about a certain setting than we need
to encode different generic settings.
- Add a cross-talk API to the pin control GPIO back-end,
utilizing pinctrl_gpio_set_config() from GPIO drivers that
want to set up a certain pin configuration in the back-end.
This also includes the .set_config() refactoring of the
GPIO chips, so that they pass a generic configuration for
things like debouncing and single ended (typically open
drain). This change has also been merged in an immutable
branch to the GPIO tree.
- Take hogs with a delayed work, so that we finalize probing
a pin controller before trying to get any hogs.
- For pin controllers putting all group and function definitions
into the device tree, we now have generic code to deal with
this and it is used in two drivers so far.
- Simplifications of the pin request conflict check.
- Make dt_free_map() optional.
Updates to drivers:
- pinctrl-single now use the generic helpers to generate dynamic
group and function tables from the device tree.
- Texas Instruments IOdelay configuration driver add-on to
pinctrl-single.
- i.MX: use radix trees to store groups and functions, use the new
generic group and function helpers to manage them.
- Intel: add support for hardware debouncing and 1K pull-down.
New subdriver for the Gemini Lake SoC.
- Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.
- Aspeed: use syscon cross-dependencies to set up related bits in
the LPC host controller and display controller.
- Aspeed: finalize G4 and G5 support. Fix mux configuration on
GPIOs. Add banks Y, Z, AA, AB and AC.
- AMD: support additional GPIO.
- STM32: set this controller to strict muxing mode.
STM32H743 MCU support.
- Allwinner sunxi: deep simplifications on how to support
subvariants of SoCs without adding to much SoC-specific data
for each subvariant, especially for sun5i variants. New driver
for V3s SoCs. New driver for the H5 SoC. Support A31/A31s
variants with the new variant framework.
- Mvebu: simplifications to use a MMIO and regmap abstraction.
New subdrivers for the 98DX3236, 98DX5241 SoCs.
- Samsung Exynos: delete Exynos4415 support. Add crosstalk to the
SoC driver to access regmaps. Add infrastructure for pin-bank
retention control. Clean out the pin retention control from
arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly
in the Samsung pin control driver(s).
- Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.
- Qualcomm: use raw spinlock variants: this makes the qualcomm
driver realtime-safe.
-----BEGIN PGP SIGNATURE-----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=IMY0
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Pin control bulk changes for the v4.11 kernel cycle.
Core changes:
- Switch the generic pin config argument from 16 to 24 bits, only use
8 bits for the configuration type. We might need to encode more
information about a certain setting than we need to encode
different generic settings.
- Add a cross-talk API to the pin control GPIO back-end, utilizing
pinctrl_gpio_set_config() from GPIO drivers that want to set up a
certain pin configuration in the back-end.
This also includes the .set_config() refactoring of the GPIO chips,
so that they pass a generic configuration for things like
debouncing and single ended (typically open drain). This change has
also been merged in an immutable branch to the GPIO tree.
- Take hogs with a delayed work, so that we finalize probing a pin
controller before trying to get any hogs.
- For pin controllers putting all group and function definitions into
the device tree, we now have generic code to deal with this and it
is used in two drivers so far.
- Simplifications of the pin request conflict check.
- Make dt_free_map() optional.
Updates to drivers:
- pinctrl-single now use the generic helpers to generate dynamic
group and function tables from the device tree.
- Texas Instruments IOdelay configuration driver add-on to
pinctrl-single.
- i.MX: use radix trees to store groups and functions, use the new
generic group and function helpers to manage them.
- Intel: add support for hardware debouncing and 1K pull-down. New
subdriver for the Gemini Lake SoC.
- Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.
- Aspeed: use syscon cross-dependencies to set up related bits in the
LPC host controller and display controller.
- Aspeed: finalize G4 and G5 support. Fix mux configuration on GPIOs.
Add banks Y, Z, AA, AB and AC.
- AMD: support additional GPIO.
- STM32: set this controller to strict muxing mode. STM32H743 MCU
support.
- Allwinner sunxi: deep simplifications on how to support subvariants
of SoCs without adding to much SoC-specific data for each
subvariant, especially for sun5i variants. New driver for V3s SoCs.
New driver for the H5 SoC. Support A31/A31s variants with the new
variant framework.
- Mvebu: simplifications to use a MMIO and regmap abstraction. New
subdrivers for the 98DX3236, 98DX5241 SoCs.
- Samsung Exynos: delete Exynos4415 support. Add crosstalk to the SoC
driver to access regmaps. Add infrastructure for pin-bank retention
control. Clean out the pin retention control from
arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly in
the Samsung pin control driver(s).
- Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.
- Qualcomm: use raw spinlock variants: this makes the qualcomm driver
realtime-safe"
* tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (111 commits)
pinctrl: samsung: Fix return value check in samsung_pinctrl_get_soc_data()
pinctrl: intel: unlock on error in intel_config_set_pull()
pinctrl: berlin: make bool drivers explicitly non-modular
pinctrl: spear: make bool drivers explicitly non-modular
pinctrl: mvebu: make bool drivers explicitly non-modular
pinctrl: sunxi: make sun5i explicitly non-modular
pinctrl: sunxi: Remove stray printk call in sun5i driver's probe function
pinctrl: samsung: mark PM functions as __maybe_unused
pinctrl: sunxi: Remove redundant A31s pinctrl driver
pinctrl: sunxi: Support A31/A31s with pinctrl variants
pinctrl: Amend bindings for STM32 pinctrl
pinctrl: Add STM32 pinctrl driver DT bindings
pinctrl: stm32: Add STM32H743 MCU support
include: dt-bindings: Add STM32H7 pinctrl DT defines
gpio: aspeed: Remove dependence on GPIOF_* macros
pinctrl: stm32: fix bad location of gpiochip_lock_as_irq
drivers: pinctrl: add driver for Allwinner H5 SoC
pinctrl: intel: Add Intel Gemini Lake pin controller support
pinctrl: intel: Add support for 1k additional pull-down
pinctrl: intel: Add support for hardware debouncer
...
In case of error, the function devm_ioremap() returns NULL pointer not
ERR_PTR(). Fix by using devm_ioremap_resource instead of devm_ioremap.
Fixes: 8b1bd11c1f ("pinctrl: samsung: Add the support the multiple IORESOURCE_MEM for one pin-bank")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to unlock before returning -EINVAL on this error path.
Fixes: 04cc058f0c ("pinctrl: intel: Add support for 1k additional pull-down")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate,
meaning that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: "Antoine Ténart" <antoine.tenart@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Hongzhou Yang <hongzhou.yang@mediatek.com>
Cc: Thomas Hebb <tommyhebb@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate,
meaning that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the drivers there is no doubt they are builtin-only. All
drivers get the exact same change, so they are handled in batch.
Changes are (1) use init.h header in place of module.h header,
(2) delete module_exit related code, (3) delete MODULE_DEVICE_TABLE,
and (4) delete MODULE_LICENCE/MODULE_AUTHOR and associated tags.
None of these drivers were using module_init() so we don't have to
worry about the init ordering getting changed with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE etc. tags since all that information
is already contained at the top of each file in the comments.
Cc: spear-devel@list.st.com
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate, meaning
that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the drivers there is no doubt they are builtin-only.
All drivers get the exact same change, so they are handled in batch.
Changes are (1) use builtin_platform_driver, (2) dont use module.h
(3) delete module_exit related code, (4) delete MODULE_DEVICE_TABLE,
and (5) delete MODULE_LICENCE/MODULE_AUTHOR and associated tags.
For the dove driver we explicitly disallow a driver unbind, since
that doesn't have a sensible use case anyway, and it allows us to
drop the ".remove" code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
We deleted the MODULE_LICENSE etc. tags since all that information
is already contained at the top of the file in the comments.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We had all these corrected in commit 0c8c6ba00c ("pinctrl: sunxi:
make bool drivers explicitly non-modular") but this new one recently
crept in.
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/sunxi/Kconfig:config PINCTRL_SUN5I
drivers/pinctrl/sunxi/Kconfig: def_bool MACH_SUN5I
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a stray printk call in the new sun5i pinctrl driver's probe
function.
Remove it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The rework of the suspend/resume handling uses the wrong #ifdef check, leading
to a build warning without CONFIG_PM_SLEEP:
drivers/pinctrl/samsung/pinctrl-samsung.c:1142:12: error: 'samsung_pinctrl_resume' defined but not used [-Werror=unused-function]
drivers/pinctrl/samsung/pinctrl-samsung.c:1092:12: error: 'samsung_pinctrl_suspend' defined but not used [-Werror=unused-function]
Using a __maybe_unused annotation instead of the #ifdef is a simple way to
avoid this problem class.
Fixes: 2b24efa8e5 ("pinctrl: samsung: Replace syscore ops with standard platform device pm_ops")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we can support the A31s pin controller with the A31 driver
using the new variants support, the independent A31s driver becomes
redundant.
Remove it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A31s is a trimmed down version of the A31. Some hardware blocks
are removed, thus not available for muxing on the external pins.
Some external pins were directly removed.
This makes it easy to support the A31s pin controller with the A31
driver. We just mark the pins and functions that were trimmed as
A31 only.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move gpio lock as irq from "domain alloc" callback to "domain activate"
callback. It will allow to use gpiolib sysfs correctly.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on the Allwinner H5 datasheet and the pinctrl driver of the
backward-compatible H3 this introduces the pin multiplex assignments for
the H5 SoC.
H5 introduced some more pin functions (e.g. three more groups of TS
pins, and one more groups of SIM pins) than H3.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to VLI64 Intel Atom E3800 Specification Update (#329901)
concurrent read accesses may result in returning 0xffffffff and write
accesses may be dropped silently.
To workaround all accesses must be protected by locks.
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Debounce value is set globally per community. Otherwise user will easily
get a kernel crash when they start using the feature:
BUG: unable to handle kernel paging request at ffffc900003be000
IP: byt_gpio_dbg_show+0xa9/0x430
Make it clear in byt_gpio_reg().
Note that this fix just prevents kernel to crash, but doesn't make any
difference to the existing logic. It means the last caller will win the
trade and debounce value will be configured accordingly. The actual
logic fix needs to be thought about and it's not as important as crash
fix. That's why the latter goes separately and right now.
Fixes: 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
Cc: Cristina Ciocan <cristina.ciocan@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit 04ff5a095d ("pinctrl: baytrail: Rectify debounce support")
almost fixes the logic of debuonce but missed couple of things, i.e.
typo in mask when disabling debounce and lack of enabling it back.
This patch addresses above issues.
Reported-by: Jean Delvare <jdelvare@suse.de>
Fixes: 04ff5a095d ("pinctrl: baytrail: Rectify debounce support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver adds pinctrl/GPIO support for Intel Gemini Lake SoC. The
GPIO controller is based on the next generation GPIO hardware but still
compatible with the one supported by the Intel core pinctrl/GPIO driver.
This commit includes material from David E. Box.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The next generation Intel GPIO hardware supports additional 1k pull-down
per-pad. Add support for this to the Intel core pinctrl driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The next generation Intel GPIO hardware has two additional registers
PADCFG2 and PADCFG3. The latter is marked as reserved but the former
includes configuration for per-pad hardware debouncer.
This patch adds support for that in the Intel pinctrl core driver. Since
these are additional features on top of the current generation hardware,
we use revision number and feature flags to enable this if detected.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This pinctrl driver supports the 98DX3236, 98DX3336 and 98DX4251 SoCs
from Marvell.
Signed-off-by: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no need to take pointer of a pointer to an array of SoC data in
platform driver.
Do it in the same way as it's done for ACPI.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Not every pin can be configured. Add missed check to prevent access
violation.
Fixes: 4e80c8f505 ("pinctrl: intel: Add Intel Merrifield pin controller support")
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 07fe64ba21 ("pinctrl: sunxi: Handle bias disable") actually
enforced enforced the disabling of the pull up/down resistors instead of
ignoring it like it was done before.
This was part of a wider rework to switch to the generic pinconf bindings,
and was meant to be merged together with DT patches that were switching to
it, and removing what was considered default values by both the binding and
the boards. This included no bias on a pin.
However, those DT patches were delayed to 4.11, which would be fine only
for a significant number boards having the bias setup wrong, which in turns
break the MMC on those boards (and possibly other devices too).
In order to avoid conflicts as much as possible, bring back the old
behaviour for 4.10, and we'll revert that commit once all the DT bits will
have landed.
Tested-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Once the dependency on PMU driver (for pad retention control) has been
removed, there is no reason to use syscore_ops based suspend/resume.
This patch replaces it with standard platform device pm_ops based solution.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch moves pad retention control from S5PV210 machine code to
Exynos pin controller driver. This helps to avoid possible ordering
and logical dependencies between machine and pin control code. Till
now it worked fine only because sys_ops for machine code and pin
controller were called in registration order.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
For mach-s5pv210:
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch moves pad retention control from PMU driver to Exynos pin
controller driver. This helps to avoid possible ordering and logical
dependencies between machine, PMU and pin control code. Till now it
worked fine only because sys_ops for PMU and pin controller were called
in registration order.
This is also a preparation for adding new features to Exynos pin
controller driver, like runtime power management and suspending
individual pin controllers, which might be a part of some power domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Apparently each GPIO pad's register are 16 bytes, so multiply the pad_map
by that. The same is done in byt_gpio_reg the only other place where
pad_map is used.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pad retention control after suspend/resume cycle should be done from pin
controller driver instead of PMU (power management unit) driver to avoid
possible ordering and logical dependencies. Till now it worked fine only
because PMU driver registered its sys_ops after pin controller.
This patch adds infrastructure to handle pad retention during pin control
driver resume.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
'enable' parameter has been removed a while ago, so all code for handling
it can be simply removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Martin Blumenstingl
Markus Elfring
Shyam Sundar S K
Gregory CLEMENT
Masahiro Yamada
Shawn Guo
Linus Walleij
Wei Yongjun
Sergei Shtylyov
Kuninori Morimoto
Geert Uytterhoeven
Takeshi Kihara
Linus Torvalds
Thierry Reding
Paul Gortmaker
Andrew Jeffery
Alexandre TORGUE
Andy Shevchenko
Jacopo Mondi
Mika Westerberg
Chanwoo Choi
Alexandre Belloni
Jesper Nilsson
Tony Lindgren
Jerome Brunet
Neil Armstrong
John Keeping
Masanari Iida
Charles Keepax
Marek Szyprowski
Hans de Goede
Andy Yan
Christian Lamparter
Patrice Chotard
Bjorn Andersson
Andrzej Hajda
Peter Robinson
Jeffy Chen
Julia Cartwright
Timur Tabi
david.wu
Icenowy Zheng
Rick Altherr
Kunihiko Hayashi
Dan Carpenter
Chen-Yu Tsai
Arnd Bergmann
Alexander Stein
Kalyan Kinthada
Maxime Ripard
Jisheng Zhang