For some reason the controller does not support 8 byte transfers (but
does support all other powers of 2 up to 128). In this case fall back
to 4 bytes. In addition, fall back to 128 bytes when any larger power
of 2 would be possible within the alignment constraints, as this is
the maximum supported.
It makes no sense to outright reject 8 or >128 bytes just because the
alignment constraints make those the maximum possible size given the
parameters for the transaction. For instance, this can result in a DMA
from/to an 8 byte aligned address failing.
It is perfectly safe to fall back to smaller transfer sizes, the only
consequence is reduced transfer efficiency, which is far better than
not allowing the transfer at all.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Several function prototypes did not match the dmaengine API they were
implementing, resulting in build warnings. Correct these.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If DMA interrupt comes and is latched by IRQ controller during the
execution of dma_terminate_all(), dma_irq routine will be executed
after dma terminated, and it will cause kernel panic.
We clear DMA interrupts in dma_terminate_all() to avoid this useless
interrupt.
Signed-off-by: Yanchang Li <Yanchang.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add device tree bindings documentation for the
lpc1850-dmamux DMA router.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for DMA on NXP LPC18xx/43xx platforms which has
a multiplexer in front of the PL080 dma request lines.
The mux is a single register in the LPC18xx/43xx CREG block
and can multiplex up to 4 request lines to each of the 16
lines on the PL080.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This introduces device tree bindings for the PL08x DMA controllers
when used with fixed signal assignment per channel, i.e. if each
channel on the PL08x is assigned precisely one burst/single signal
set.
[je: remove channel sub-node parsing, use cell value to assign AHB]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This fixes the following error:
drivers/dma/pxa_dma.c: In function ‘dbg_show_requester_chan’:
drivers/dma/pxa_dma.c:192:2: error: void value not ignored as it ought to be
pos += seq_printf(s, "DMA channel %d requester :\n", phy->idx);
^
drivers/dma/pxa_dma.c:197:8: error: void value not ignored as it ought to be
!!(drcmr & DRCMR_MAPVLD));
^
scripts/Makefile.build:258: recipe for target 'drivers/dma/pxa_dma.o' failed
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Inline function __dma_request_slave_channel_compat() doesn't modify "name"
argument but passes it to dma_request_slave_channel() which already takes
it as a constant.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Don't use the direction passed in the configuration, and rely on each
transfer's direction to prepare the transfers. This will enable
future removal of direction parameter from dma_slave_config.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This adds new descriptor flag for reusing a descriptor by submitting
multiple times by a client, for example video buffer.
Add helper APIs for this as well
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by:Robert Jarzmik <robert.jarzmik@free.fr>
As discussed recently the meaning of DMA_CTRL_ACK is that a desc cannot be
reused by provider until the client acknowledges receipt, i.e. has has a
chance to establish any dependency chains. So update documentation
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by:Robert Jarzmik <robert.jarzmik@free.fr>
IOAT_COMPLETION_PENDING flag was deprecated for v2 and v3 drivers but was
not cleaned up. Doing that now. The commit deprecated this flag was
4dec23d7 ioatdma: fix race between updating ioat->head and
IOAT_COMPLETION_PENDING.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
./scripts/kerne-doc is reporting errors on dma.h. Clean up all reported
errors.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since we are a "single" device driver now we no longer require the function
pointers in ioatdma_device. Remove.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Moving the relevant functions to their respective .c files and removal of
dma_v3.c file. Also removed various ioat3 references when appropriate.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Move all DMA descriptor prepping functions to prep.c file. Fixup all
broken bits caused by the move.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Moving all the init routines to init.c and fixup anything broken during
the move.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Move and fixup all sysfs related bits to sysfs.c file.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Clean out dma_v2 and remove ioat2 calls since we are moving everything
to just ioat.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Changing the variable names for ioatdma_device to be consistently named
ioat_dma instead of device/dma in order to avoid confusion and distinct
from struct device. This will clearly indicate that it is an
ioatdma_device. This also make all the naming consistent that the dma
device is ioat_dma and all the channels are ioat_chan.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Kill the common ioatdma channel structure and everything that is not
dma_chan to be ioat_dma_chan. Since we don't have to worry about v1
and v2 ioatdma anymore this makes it much cleaner and obvious for
maintenance.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Removal of support for ioatdma v2 device support.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cleaning up of ioat1 specific code as it is no longer supported
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Removal of any devices that are ioatdma pre-3.0. This is the first step
in attempting to clean up the ioatdma driver and remove hw no longer
supported.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the allocation order is 16, then the u16 count will overflow and wrap
to zero when assigned the value 1 << 16.
Change the type of 'total_descs' to int, so that it is large enough to
store a value equal or greater than 1 << 16.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the allocation order is 16, then the u16 index will overflow and wrap
to zero instead of being equal or greater than 1 << 16. The loop
condition will always be true, and the loop will run until all the
memory resources are depleted.
Change the type of index 'i' to u32, so that it is large enough to store
a value equal or greater than 1 << 16.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The functions irq_irq_err and ipu_irq_fn are identical plus/minus the
comments. Remove one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The XDMAC also supports memset operations over discontiguous areas. Add the
necessary logic to support this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The current API allows the driver to accelerate memset by using the DMA
controller.
However, it does so over a contiguous memory area, which might proves
inefficient when you have to do it over a non-contiguous yet repititive
pattern, since you have to create a number of descriptors and then submit
each other.
Add a memset operation going over a scatter list to handle such cases in a
single call.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Most drivers need to set constraints on the buffer alignment for async tx
operations. However, even though it is documented, some drivers either use
a defined constant that is not matching what the alignment variable expects
(like DMA_BUSWIDTH_* constants) or fill the alignment in bytes instead of
power of two.
Add a new enum for these alignments that matches what the framework
expects, and convert the drivers to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If CONFIG_SH_DMAE_BASE (which is required for DMA engine support for
legacy SH, SH/R-Mobile, and R-Car Gen1, but not for R-Car Gen2) is not
enabled, but CONFIG_RCAR_DMAC (for R-Car Gen2 DMA engine support) is,
and the DTS doesn't provide a "dmas" property for a device,
dma_request_slave_channel_compat() incorrectly succeeds, and returns a
DMA channel.
However, when trying to use that DMA channel later, it fails with:
rcar-dmac e6700000.dma-controller: rcar_dmac_prep_slave_sg: bad parameter: len=1, id=-22
(Fortunately most drivers can handle this failure, and fall back to
PIO)
The reason for this is that a NULL legacy filter function is used, which
actually means "all channels are OK", not "do not match".
If CONFIG_SH_DMAE_BASE is enabled (like in shmobile_defconfig, which
supports other SoCs besides R-Car Gen2), shdma_chan_filter() correctly
returns false, as no available channel on R-Car Gen2 matches a
shdma-base channel.
If the DTS does provide a "dmas" property, dma_request_slave_channel()
succeeds, and legacy filter-based matching is not used.
To fix this, change shdma_chan_filter from being NULL to a dummy
function that always returns false, like is done on other platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds DEV_TO_DEV support for i.MX SDMA driver to support data
transfer between two peripheral FIFOs.
The per_2_per script requires two peripheral addresses and two DMA
requests, and it need to check the src addr and dst addr is in the SPBA
bus space or in the AIPS bus space.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc while we
already have a pointer to corresponding irq_desc.
This is also a preparation for the removal of the 'irq' argument from
interrupt flow handlers.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
All hardware accesses are done under virtual channel lock. That's why specific
channel lock is excessive and can be removed safely. This has been tested on
Intel Medfield and Merrifield.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The dmaengine core assumes that async DMA devices will only be removed
when they not used anymore, or it assumes dma_async_device_unregister()
will only be called by dma driver exit routines. But this assumption is
not true for the IOAT driver, which calls dma_async_device_unregister()
from ioat_remove(). So current IOAT driver doesn't support device
hot-removal because it may cause system crash to hot-remove an inuse
IOAT device.
To support CPU socket hot-removal, all PCI devices, including IOAT
devices embedded in the socket, will be hot-removed. The idea solution
is to enhance the dmaengine core and IOAT driver to support hot-removal,
but that's too hard.
This patch implements a hack to disable IOAT devices under hotplug-capable
CPU socket so it won't break socket hot-removal.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This allows claiming of non-RAID channels as a private channel. This
prevents breakage of MDRAID using the IOATDMA channels via
async_tx but also allows agents such as NTB to claim channels
exclusively for its usages.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Removing static analysis error:-
Possible null pointer dereference: xt
Because currently xt is dereferenced before NULL check,
Thus Use it after NULL Check.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Reviewed-by: Vaneet Narang <v.narang@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
While at it, change the label 'err' to a more descriptive naming.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 3b62286d0e ("dmaengine: Remove FSF mailing addresses") left Free
Software Foundation mailing address still in two files. Remove it now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
A new intel_pmc_ipc driver, a symmetrical allocation and free fix in
dell-laptop, a couple minor fixes, and some updated documentation in the
dell-laptop comments.
intel_pmc_ipc:
- Add Intel Apollo Lake PMC IPC driver
tc1100-wmi:
- Delete an unnecessary check before the function call "kfree"
dell-laptop:
- Fix allocating & freeing SMI buffer page
- Show info about WiGig and UWB in debugfs
- Update information about wireless control
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVmM8aAAoJEKbMaAwKp364iUkH/jihOduWkDTzzzxRP2Dv2nEh
qyvE94Nc9A9dl87C2+II/Pi1s8h4CJOQpl70syYYPc4FdF70hpvP8TbHkgCWrY/d
F8CoS9L9keviMtGOWlbEL9hBjfSDNwTMESTrDxrwhA04TSAwjDmXhhiUOF5FjFJm
CX5+ZQ3iXEH6KsENR+Er54J9+6WKE6IuRcnnKCapnPQ8cEYeVn+WEPyzHCOy8Pg3
xzzUar3/knS2VMIb5eIVpaKFvD9P9qBsC/gQ0pk1Y+686gwQZMVURDv8lw8hfXpx
TJDOXk21P8WbSH1r+jwax5wLjLge7vJtYG2Deye6MUgvSgg+O2tSVCv9SMQR088=
=WUgr
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.2-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull late x86 platform driver updates from Darren Hart:
"The following came in a bit later and I wanted them to bake in next a
few more days before submitting, thus the second pull.
A new intel_pmc_ipc driver, a symmetrical allocation and free fix in
dell-laptop, a couple minor fixes, and some updated documentation in
the dell-laptop comments.
intel_pmc_ipc:
- Add Intel Apollo Lake PMC IPC driver
tc1100-wmi:
- Delete an unnecessary check before the function call "kfree"
dell-laptop:
- Fix allocating & freeing SMI buffer page
- Show info about WiGig and UWB in debugfs
- Update information about wireless control"
* tag 'platform-drivers-x86-v4.2-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
intel_pmc_ipc: Add Intel Apollo Lake PMC IPC driver
tc1100-wmi: Delete an unnecessary check before the function call "kfree"
dell-laptop: Fix allocating & freeing SMI buffer page
dell-laptop: Show info about WiGig and UWB in debugfs
dell-laptop: Update information about wireless control
Pull more vfs updates from Al Viro:
"Assorted VFS fixes and related cleanups (IMO the most interesting in
that part are f_path-related things and Eric's descriptor-related
stuff). UFS regression fixes (it got broken last cycle). 9P fixes.
fs-cache series, DAX patches, Jan's file_remove_suid() work"
[ I'd say this is much more than "fixes and related cleanups". The
file_table locking rule change by Eric Dumazet is a rather big and
fundamental update even if the patch isn't huge. - Linus ]
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (49 commits)
9p: cope with bogus responses from server in p9_client_{read,write}
p9_client_write(): avoid double p9_free_req()
9p: forgetting to cancel request on interrupted zero-copy RPC
dax: bdev_direct_access() may sleep
block: Add support for DAX reads/writes to block devices
dax: Use copy_from_iter_nocache
dax: Add block size note to documentation
fs/file.c: __fget() and dup2() atomicity rules
fs/file.c: don't acquire files->file_lock in fd_install()
fs:super:get_anon_bdev: fix race condition could cause dev exceed its upper limitation
vfs: avoid creation of inode number 0 in get_next_ino
namei: make set_root_rcu() return void
make simple_positive() public
ufs: use dir_pages instead of ufs_dir_pages()
pagemap.h: move dir_pages() over there
remove the pointless include of lglock.h
fs: cleanup slight list_entry abuse
xfs: Correctly lock inode when removing suid and file capabilities
fs: Call security_ops->inode_killpriv on truncate
fs: Provide function telling whether file_remove_privs() will do anything
...
Commit 835a6a2f86 ("Bluetooth: Stop sabotaging list poisoning")
thought that the code was sabotaging the list poisoning when NULL'ing
out the list pointers and removed it.
But what was going on was that the bluetooth code was using NULL
pointers for the list as a way to mark it empty, and that commit just
broke it (and replaced the test with NULL with a "list_empty()" test on
a uninitialized list instead, breaking things even further).
So fix it all up to use the regular and real list_empty() handling
(which does not use NULL, but a pointer to itself), also making sure to
initialize the list properly (the previous NULL case was initialized
implicitly by the session being allocated with kzalloc())
This is a combination of patches by Marcel Holtmann and Tedd Ho-Jeong
An.
[ I would normally expect to get this through the bt tree, but I'm going
to release -rc1, so I'm just committing this directly - Linus ]
Reported-and-tested-by: Jörg Otte <jrg.otte@gmail.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Original-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Original-by: Marcel Holtmann <marcel@holtmann.org>:
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull SCSI target updates from Nicholas Bellinger:
"It's been a busy development cycle for target-core in a number of
different areas.
The fabric API usage for se_node_acl allocation is now within
target-core code, dropping the external API callers for all fabric
drivers tree-wide.
There is a new conversion to RCU hlists for se_node_acl and
se_portal_group LUN mappings, that turns fast-past LUN lookup into a
completely lockless code-path. It also removes the original
hard-coded limitation of 256 LUNs per fabric endpoint.
The configfs attributes for backends can now be shared between core
and driver code, allowing existing drivers to use common code while
still allowing flexibility for new backend provided attributes.
The highlights include:
- Merge sbc_verify_dif_* into common code (sagi)
- Remove iscsi-target support for obsolete IFMarker/OFMarker
(Christophe Vu-Brugier)
- Add bidi support in target/user backend (ilias + vangelis + agover)
- Move se_node_acl allocation into target-core code (hch)
- Add crc_t10dif_update common helper (akinobu + mkp)
- Handle target-core odd SGL mapping for data transfer memory
(akinobu)
- Move transport ID handling into target-core (hch)
- Move task tag into struct se_cmd + support 64-bit tags (bart)
- Convert se_node_acl->device_list[] to RCU hlist (nab + hch +
paulmck)
- Convert se_portal_group->tpg_lun_list[] to RCU hlist (nab + hch +
paulmck)
- Simplify target backend driver registration (hch)
- Consolidate + simplify target backend attribute implementations
(hch + nab)
- Subsume se_port + t10_alua_tg_pt_gp_member into se_lun (hch)
- Drop lun_sep_lock for se_lun->lun_se_dev RCU usage (hch + nab)
- Drop unnecessary core_tpg_register TFO parameter (nab)
- Use 64-bit LUNs tree-wide (hannes)
- Drop left-over TARGET_MAX_LUNS_PER_TRANSPORT limit (hannes)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (76 commits)
target: Bump core version to v5.0
target: remove target_core_configfs.h
target: remove unused TARGET_CORE_CONFIG_ROOT define
target: consolidate version defines
target: implement WRITE_SAME with UNMAP bit using ->execute_unmap
target: simplify UNMAP handling
target: replace se_cmd->execute_rw with a protocol_data field
target/user: Fix inconsistent kmap_atomic/kunmap_atomic
target: Send UA when changing LUN inventory
target: Send UA upon LUN RESET tmr completion
target: Send UA on ALUA target port group change
target: Convert se_lun->lun_deve_lock to normal spinlock
target: use 'se_dev_entry' when allocating UAs
target: Remove 'ua_nacl' pointer from se_ua structure
target_core_alua: Correct UA handling when switching states
xen-scsiback: Fix compile warning for 64-bit LUN
target: Remove TARGET_MAX_LUNS_PER_TRANSPORT
target: use 64-bit LUNs
target: Drop duplicate + unused se_dev_check_wce
target: Drop unnecessary core_tpg_register TFO parameter
...
An abstraction layer was added to allow the hardware and clients to be
easily added. This required rewriting the NTB transport layer for this
abstraction layer. This modification will allow future
"high performance" NTB clients.
In addition to this change, a number of performance modifications were
added. These changes include NUMA enablement, using CPU memcpy instead
of asyncdma, and modification of NTB layer MTU size.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=CyfQ
-----END PGP SIGNATURE-----
Merge tag 'ntb-4.2' of git://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"This includes a pretty significant reworking of the NTB core code, but
has already produced some significant performance improvements.
An abstraction layer was added to allow the hardware and clients to be
easily added. This required rewriting the NTB transport layer for
this abstraction layer. This modification will allow future "high
performance" NTB clients.
In addition to this change, a number of performance modifications were
added. These changes include NUMA enablement, using CPU memcpy
instead of asyncdma, and modification of NTB layer MTU size"
* tag 'ntb-4.2' of git://github.com/jonmason/ntb: (22 commits)
NTB: Add split BAR output for debugfs stats
NTB: Change WARN_ON_ONCE to pr_warn_once on unsafe
NTB: Print driver name and version in module init
NTB: Increase transport MTU to 64k from 16k
NTB: Rename Intel code names to platform names
NTB: Default to CPU memcpy for performance
NTB: Improve performance with write combining
NTB: Use NUMA memory in Intel driver
NTB: Use NUMA memory and DMA chan in transport
NTB: Rate limit ntb_qp_link_work
NTB: Add tool test client
NTB: Add ping pong test client
NTB: Add parameters for Intel SNB B2B addresses
NTB: Reset transport QP link stats on down
NTB: Do not advance transport RX on link down
NTB: Differentiate transport link down messages
NTB: Check the device ID to set errata flags
NTB: Enable link for Intel root port mode in probe
NTB: Read peer info from local SPAD in transport
NTB: Split ntb_hw_intel and ntb_transport drivers
...
Alex Smith
Yanchang Li
Joachim Eastwood
Linus Walleij
Robert Jarzmik
Jarkko Nikula
Robert Jarzmik
Vinod Koul
Dave Jiang
Allen Hubbe
Thomas Gleixner
Maxime Ripard
Geert Uytterhoeven
Shengjiu Wang
Jiang Liu
Andy Shevchenko
Maninder Singh
Fabio Estevam
Linus Torvalds
Al Viro