Convert warnings to info as not all platforms may
have all the thresholds and sensors enabled.
Signed-off-by: Wei Ni <wni@nvidia.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
MT8183 has two built-in thermal controllers with total six thermal
sensors. And it doesn't have bank, so doesn't need to select bank.
This patch adds support for mt8183.
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
For past ic designs, the thermal controller should select banks before
reading the thermal sensor.
And the new ic design architecture removes this mechanism.
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
One thermal controller can read four sensors at most,
so we need to add controller_offset for the project with
more than four sensors to reuse the same register settings.
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add calibration item in thermal_data to support
the project with different calibration coefficient.
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Each project has different number of vts settings.
For the MT2701 just have to set three vts, but the
original code flow add five unnecessary vts.
Add common index of vts settings for scalablity,
and reduce the setting of unnecessary vts.
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The index of msr and adcpnp should match the sensor
which belongs to the selected bank in the for loop.
Fixes: b7cf005373 ("thermal: Add Mediatek thermal driver for mt2701.")
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The QorIQ Layerscape SoC has several thermal sensors but the current
driver only supports one.
Massage the code to be sensor oriented and allow the support for
multiple sensors.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Stingray SoC has six temperature sensor and those are
configured, controlled and accessed to read temperature
and update in DDR memory using m0 firmware.
All six sensors has been given 4 bytes of memory in DDR
to write temperature in millivolts.
This thermal driver read temperature values from DDR
because no direct access to sensors.
Like this all temparature sensors are monitored and
trips at critical temperature.
If driver can't handle thermal runaways because of
any unknown reason, then firmware in m0 Processor
will handle.
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Vikram Prakash <vikram.prakash@broadcom.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Make it clear that it is a failure if the cpufreq driver was unable to
register as a cooling device. Makes it easier to find in logs and
grepping for words like fail, err, warn.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Make it easier to debug devicetree definition in case of errors.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The CPU cooling driver (cpu_cooling.c) allows the platform's cpufreq
driver to register as a cooling device and cool down the platform by
throttling the CPU frequency. In order to be able to auto-register a
cpufreq driver as a cooling device from the cpufreq core, we need access
to code inside cpu_cooling.c which, in turn, accesses code inside
thermal core.
CPU_FREQ is a bool while THERMAL is tristate. In some configurations
(e.g. allmodconfig), CONFIG_THERMAL ends up as a module while
CONFIG_CPU_FREQ is compiled in. This leads to following error:
drivers/cpufreq/cpufreq.o: In function `cpufreq_offline':
cpufreq.c:(.text+0x407c): undefined reference to `cpufreq_cooling_unregister'
drivers/cpufreq/cpufreq.o: In function `cpufreq_online':
cpufreq.c:(.text+0x70c0): undefined reference to `of_cpufreq_cooling_register'
Given that platforms using CPU_THERMAL usually want it compiled-in so it
is available early in boot, make CPU_THERMAL depend on THERMAL being
compiled-in instead of allowing it to be a module.
As a result of this change, get rid of the ugly (!CPU_THERMAL ||
THERMAL) dependency in all cpufreq drivers using CPU_THERMAL.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull thermal management fixes from Zhang Rui:
- Fix a race condition that sysfs could be accessed before necessary
initialization in int340x thermal driver. (Aaron Hill)
- Fix a NULL vs IS_ERR() check in int340x thermal driver. (Dan
Carpenter)
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
drivers: thermal: int340x_thermal: Fix sysfs race condition
thermal: int340x_thermal: Fix a NULL vs IS_ERR() check
Changes since V1:
* Use dev_info instead of printk
* Use dev_warn instead of BUG_ON
Previously, sysfs_create_group was called before all initialization had
fully run - specifically, before pci_set_drvdata was called. Since the
sysctl group is visible to userspace as soon as sysfs_create_group
returns, a small window of time existed during which a process could read
from an uninitialized/partially-initialized device.
This commit moves the creation of the sysctl group to after all
initialized is completed. This ensures that it's impossible for
userspace to read from a sysctl file before initialization has fully
completed.
To catch any future regressions, I've added a check to ensure
that proc_thermal_emum_mode is never PROC_THERMAL_NONE when a process
tries to read from a sysctl file. Previously, the aforementioned race
condition could result in the 'else' branch
running while PROC_THERMAL_NONE was set,
leading to a null pointer deference.
Signed-off-by: Aaron Hill <aa1ronham@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
After commit 5d32a66541 (PCI/ACPI: Allow ACPI to be built without
CONFIG_PCI set) dependencies on CONFIG_PCI that previously were
satisfied implicitly through dependencies on CONFIG_ACPI have to be
specified directly.
IOSF_CORE depends on PCI. For this reason, add a direct dependency on
CONFIG_PCI.
Fixes: 5d32a66541 ("PCI/ACPI: Allow ACPI to be built without CONFIG_PCI set")
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull thermal management updates from Zhang Rui:
- Add locking for cooling device sysfs attribute in case the cooling
device state is changed by userspace and thermal framework
simultaneously. (Thara Gopinath)
- Fix a problem that passive cooling is reset improperly after system
suspend/resume. (Wei Wang)
- Cleanup the driver/thermal/ directory by moving intel and qcom
platform specific drivers to platform specific sub-directories. (Amit
Kucheria)
- Some trivial cleanups. (Lukasz Luba, Wolfram Sang)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal/intel: fixup for Kconfig string parsing tightening up
drivers: thermal: Move QCOM_SPMI_TEMP_ALARM into the qcom subdir
drivers: thermal: Move various drivers for intel platforms into a subdir
thermal: Fix locking in cooling device sysfs update cur_state
Thermal: do not clear passive state during system sleep
thermal: zx2967_thermal: simplify getting .driver_data
thermal: st: st_thermal: simplify getting .driver_data
thermal: spear_thermal: simplify getting .driver_data
thermal: rockchip_thermal: simplify getting .driver_data
thermal: int340x_thermal: int3400_thermal: simplify getting .driver_data
thermal: remove unused function parameter
Pull thermal SoC updates from Eduardo Valentin:
- Tegra DT binding documentation for Tegra194
- Armada now supports ap806 and cp110
- RCAR thermal now supports R8A774C0 and R8A77990
- Fixes on thermal_hwmon, IMX, generic-ADC, ST, RCAR, Broadcom,
Uniphier, QCOM, Tegra, PowerClamp, and Armada thermal drivers.
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal: (22 commits)
thermal: generic-adc: Fix adc to temp interpolation
thermal: rcar_thermal: add R8A77990 support
dt-bindings: thermal: rcar-thermal: add R8A77990 support
thermal: rcar_thermal: add R8A774C0 support
dt-bindings: thermal: rcar-thermal: add R8A774C0 support
dt-bindings: cp110: document the thermal interrupt capabilities
dt-bindings: ap806: document the thermal interrupt capabilities
MAINTAINERS: thermal: add entry for Marvell MVEBU thermal driver
thermal: armada: add overheat interrupt support
thermal: st: fix Makefile typo
thermal: uniphier: Convert to SPDX identifier
thermal/intel_powerclamp: Change to use DEFINE_SHOW_ATTRIBUTE macro
thermal: tegra: soctherm: Change to use DEFINE_SHOW_ATTRIBUTE macro
dt-bindings: thermal: tegra-bpmp: Add Tegra194 support
thermal: imx: save one condition block for normal case of nvmem initialization
thermal: imx: fix for dependency on cpu-freq
thermal: tsens: qcom: do not create duplicate regmap debugfs entries
thermal: armada: Use PTR_ERR_OR_ZERO in armada_thermal_probe_legacy()
dt-bindings: thermal: rcar-gen3-thermal: All variants use 3 interrupts
thermal: broadcom: use devm_thermal_zone_of_sensor_register
...
First correct the edge case to return the last element if we're
outside the range, rather than at the last element, so that
interpolation is not omitted for points between the two last entries in
the table.
Then correct the formula to perform linear interpolation based the two
points surrounding the read ADC value. The indices for temp are kept as
"hi" and "lo" to pair with the adc indices, but there's no requirement
that the temperature is provided in descendent order. mult_frac() is
used to prevent issues with overflowing the int.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The IP can manage to trigger interrupts on overheat situation from all
the sensors.
However, the interrupt source changes along with the last selected
source (ie. the last read sensor), which is an inconsistent behavior.
Avoid possible glitches by always selecting back only one channel which
will then be referenced as the "overheat_sensor" (arbitrarily: the first
in the DT which has a critical trip point filled in).
It is possible that the scan of all thermal zone nodes did not bring a
critical trip point from which the overheat interrupt could be
configured. In this case just complain but do not fail the probe.
Also disable sensor switch during overheat situations because changing
the channel while the system is too hot could clear the overheat state
by changing the source while the temperature is still very high.
Even if the overheat state is not declared, overheat interrupt must be
cleared by reading the DFX interrupt cause _after_ the temperature has
fallen down to the low threshold, otherwise future possible interrupts
would not be served. A work polls the corresponding register until the
overheat flag gets cleared in this case.
Suggested-by: David Sniatkiwicz <davidsn@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When STM32_THERMAL is enabled, this overrides all previously
enabled files in the same directory, as seen from this link failure:
ERROR: "st_thermal_pm_ops" [drivers/thermal/st/st_thermal_syscfg.ko] undefined!
ERROR: "st_thermal_register" [drivers/thermal/st/st_thermal_syscfg.ko] undefined!
ERROR: "st_thermal_unregister" [drivers/thermal/st/st_thermal_syscfg.ko] undefined!
The correct syntax in Makefile requires using += instead of :=.
Fixes: 1d69315560 ("thermal: add stm32 thermal driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Put return value checks of calling imx_init_from_nvmem_cells()
into one block to save one condition block for normal case.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The thermal driver is a standalone driver for monitoring SoC temperature
by enabling thermal sensor, so it can be enabled even when CONFIG_CPU_FREQ
is NOT set. So remove the dependency with CPU_THERMAL.
Introduce dummy function of legacy cooling register/unregister to make
thermal driver probe successfully when CONFIG_CPU_FREQ is NOT set.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Regmap would use device name to create debugfs entries. If the device
has multiple regmaps it is recommended to use name field in regmap_config.
Fix this by providing name to the regmap configs correctly.
Without this patch we would see below error on DB820c.
qcom-tsens 4a9000.thermal-sensor: Failed to create 4a9000.thermal-sensor
debugfs directory
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Using devm_thermal_zone_of_sensor_register allows to simplify some
error handling code, drop a label, and drop the remove function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
By defaul of-based thermal driver do not enable hwmon.
This patch does this explicitly, so that the temperature can be read
through the common hwmon sysfs.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Avoid warnings like this:
thermal_hwmon.h:29:1: warning: ‘thermal_remove_hwmon_sysfs’ defined but not used [-Wunused-function]
thermal_remove_hwmon_sysfs(struct thermal_zone_device *tz)
Fixes: 0dd88793aa ("thermal: hwmon: move hwmon support to single file")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
- support -y option for merge_config.sh to avoid downgrading =y to =m
- remove S_OTHER symbol type, and touch include/config/*.h files correctly
- fix file name and line number in lexer warnings
- fix memory leak when EOF is encountered in quotation
- resolve all shift/reduce conflicts of the parser
- warn no new line at end of file
- make 'source' statement more strict to take only string literal
- rewrite the lexer and remove the keyword lookup table
- convert to SPDX License Identifier
- compile C files independently instead of including them from zconf.y
- fix various warnings of gconfig
- misc cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJcJieuAAoJED2LAQed4NsGHlIP/1s0fQ86XD9dIMyHzAO0gh2f
7rylfe2kEXJgIzJ0DyZdLu4iZtwbkEUqTQrRS1abriNGVemPkfBAnZdM5d92lOQX
3iREa700AJ2xo7V7gYZ6AbhZoG3p0S9U9Q2qE5S+tFTe8c2Gy4xtjnODF+Vel85r
S0P8tF5sE1/d00lm+yfMI/CJVfDjyNaMm+aVEnL0kZTPiRkaktjWgo6Fc2p4z1L5
HFmMMP6/iaXmRZ+tHJGPQ2AT70GFVZw5ePxPcl50EotUP25KHbuUdzs8wDpYm3U/
rcESVsIFpgqHWmTsdBk6dZk0q8yFZNkMlkaP/aYukVZpUn/N6oAXgTFckYl8dmQL
fQBkQi6DTfr9EBPVbj18BKm7xI3Y4DdQ2fzTfYkJ2XwNRGFA5r9N3sjd7ZTVGjxC
aeeMHCwvGdSx1x8PeZAhZfsUHW8xVDMSQiT713+ljBY+6cwzA+2NF0kP7B6OAqwr
ETFzd4Xu2/lZcL7gQRH8WU3L2S5iedmDG6RnZgJMXI0/9V4qAA+nlsWaCgnl1TgA
mpxYlLUMrd6AUJevE34FlnyFdk8IMn9iKRFsvF0f3doO5C7QzTVGqFdJu5a0CuWO
4NBJvZjFT8/4amoWLfnDlfApWXzTfwLbKG+r6V2F30fLuXpYg5LxWhBoGRPYLZSq
oi4xN1Mpx3TvXz6WcKVZ
=r3Fl
-----END PGP SIGNATURE-----
Merge tag 'kconfig-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kconfig updates from Masahiro Yamada:
- support -y option for merge_config.sh to avoid downgrading =y to =m
- remove S_OTHER symbol type, and touch include/config/*.h files correctly
- fix file name and line number in lexer warnings
- fix memory leak when EOF is encountered in quotation
- resolve all shift/reduce conflicts of the parser
- warn no new line at end of file
- make 'source' statement more strict to take only string literal
- rewrite the lexer and remove the keyword lookup table
- convert to SPDX License Identifier
- compile C files independently instead of including them from zconf.y
- fix various warnings of gconfig
- misc cleanups
* tag 'kconfig-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (39 commits)
kconfig: surround dbg_sym_flags with #ifdef DEBUG to fix gconf warning
kconfig: split images.c out of qconf.cc/gconf.c to fix gconf warnings
kconfig: add static qualifiers to fix gconf warnings
kconfig: split the lexer out of zconf.y
kconfig: split some C files out of zconf.y
kconfig: convert to SPDX License Identifier
kconfig: remove keyword lookup table entirely
kconfig: update current_pos in the second lexer
kconfig: switch to ASSIGN_VAL state in the second lexer
kconfig: stop associating kconf_id with yylval
kconfig: refactor end token rules
kconfig: stop supporting '.' and '/' in unquoted words
treewide: surround Kconfig file paths with double quotes
microblaze: surround string default in Kconfig with double quotes
kconfig: use T_WORD instead of T_VARIABLE for variables
kconfig: use specific tokens instead of T_ASSIGN for assignments
kconfig: refactor scanning and parsing "option" properties
kconfig: use distinct tokens for type and default properties
kconfig: remove redundant token defines
kconfig: rename depends_list to comment_option_list
...
The Kconfig lexer supports special characters such as '.' and '/' in
the parameter context. In my understanding, the reason is just to
support bare file paths in the source statement.
I do not see a good reason to complicate Kconfig for the room of
ambiguity.
The majority of code already surrounds file paths with double quotes,
and it makes sense since file paths are constant string literals.
Make it treewide consistent now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Adding brackets allows to multiply the register value,
masked by TS1_RAMP_COEFF_MASK, by an ADJUST value
properly and not to multiply ADJUST by register value and
then mask the whole.
Fixes: 1d693155 ("thermal: add stm32 thermal driver")
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: David Hernandez Sanchez <david.hernandezsanchez@st.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Calling stm_thermal_read_factory_settings before clocking
internal peripheral causes bad register values and makes
temperature computation wrong.
Calling stm_thermal_read_factory_settings inside
stm_thermal_prepare fixes this problem as internal
peripheral is well clocked at this stage.
Fixes: 1d693155 ("thermal: add stm32 thermal driver")
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: David Hernandez Sanchez <david.hernandezsanchez@st.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Without this patch the thermal driver is broken on hi3660.
The dual sensors support patchset was partially merged, unfortunately
the dual thermal zones definition is not available in the DT yet, so
when the driver tries to register all the sensors that fails.
By reducing to 1 the number of sensors on the hi3660, we switch back
to the previous functionnality.
Fixes: 8c6c36846f (thermal/drivers/hisi: Add the dual clusters sensors for hi3660)
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Without this patch, the thermal driver on hi6220 and hi3660 is broken.
That is due because part of the posted patchset was merged but a small
change in the DT was dropped.
The hi6220 and hi3660 do not have an interrupt name in the DT, so
finding interrupt by name fails.
Fix this by returning back to the platform_get_irq() function call.
Fixes: 2cffaeff08 (thermal/drivers/hisi: Use platform_get_irq_byname)
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This cleans up the directory a bit allowing just one place to look for
thermal related drivers for QCOM platforms instead of being scattered in
the root directory and the qcom/ subdirectory. Compile-tested with
ARCH=arm64 defconfig and the driver explicitly enabled with menuconfig.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This cleans up the directory a bit, now that we have several other
platforms using platform-specific sub-directories. Compile-tested with
ARCH=x86 defconfig and the drivers explicitly enabled with menuconfig.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The thermal_zone_of_device_ops structure can be const as it is only
passed as the last argument of thermal_zone_of_sensor_register
and the corresponding parameter is declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The thermal_zone_of_device_ops structure can be const as it is only
passed as the last argument of devm_thermal_zone_of_sensor_register
and the corresponding parameter is declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When the armada thermal module is inserted, removed and then reinserted,
the system panics as per the messages below. The reason is that "edit"
a live resource in the resource tree twice, and end up with it pointing
to some other hardware.
Editing live resources (resources that are part of the registered
resource tree) is not permissible - the resource tree is an ordered
set of resources, sorted by start address, and when a new resource is
inserted, it is validated that it (a) fits within its parent resource
and (b) does not overlap a neighbouring resource.
Get rid of this resource editing. We can instead adjust the return
value from ioremap() as ioremap() deals with the creation of page-
based mappings - provided the adjustment does not cross a page
boundary.
SError Interrupt on CPU1, code 0xbf000000 -- SError
CPU: 1 PID: 2749 Comm: modprobe Not tainted 4.19.0+ #175
Hardware name: Marvell 8040 MACCHIATOBin Double shot (DT)
pstate: 20400085 (nzCv daIf +PAN -UAO)
pc : regmap_mmio_read+0x3c/0x60
lr : regmap_mmio_read+0x3c/0x60
sp : ffffff800d453900
x29: ffffff800d453900 x28: ffffff800096a1d0
x27: 0000000000000100 x26: ffffff80009696d8
x25: ffffff8000969000 x24: ffffffc13a588918
x23: ffffffc13a9a28a8 x22: ffffff800d4539dc
x21: 0000000000000084 x20: ffffff800d4539dc
x19: ffffffc13a5d5480 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: 0000000000000030
x11: 0101010101010101 x10: 7f7f7f7f7f7f7f7f
x9 : 0000000000000000 x8 : ffffffc13a5d5a80
x7 : 0000000000000000 x6 : 000000000000003f
x5 : 0000000000000000 x4 : 0000000000000000
x3 : ffffff800851be70 x2 : ffffff800851bd60
x1 : ffffff800d492ff8 x0 : 0000000000000000
Kernel panic - not syncing: Asynchronous SError Interrupt
CPU: 1 PID: 2749 Comm: modprobe Not tainted 4.19.0+ #175
Hardware name: Marvell 8040 MACCHIATOBin Double shot (DT)
Call trace:
dump_backtrace+0x0/0x158
show_stack+0x14/0x1c
dump_stack+0x90/0xb0
panic+0x128/0x298
print_tainted+0x0/0xa8
arm64_serror_panic+0x74/0x80
do_serror+0x5c/0xb8
el1_error+0xb4/0x144
regmap_mmio_read+0x3c/0x60
_regmap_bus_reg_read+0x18/0x20
_regmap_read+0x64/0x180
regmap_read+0x44/0x6c
armada_ap806_init+0x24/0x5c [armada_thermal]
armada_thermal_probe+0x2c8/0x37c [armada_thermal]
platform_drv_probe+0x4c/0xb0
really_probe+0x21c/0x2b4
driver_probe_device+0x58/0xfc
__driver_attach+0xd4/0xd8
bus_for_each_dev+0x50/0xa0
driver_attach+0x20/0x28
bus_add_driver+0x1c4/0x228
driver_register+0x6c/0x124
__platform_driver_register+0x4c/0x54
armada_thermal_driver_init+0x20/0x1000 [armada_thermal]
do_one_initcall+0x30/0x204
do_init_module+0x5c/0x1d4
load_module+0x1a88/0x212c
__se_sys_finit_module+0xa0/0xac
__arm64_sys_finit_module+0x1c/0x24
el0_svc_common+0x94/0xf0
el0_svc_handler+0x24/0x80
el0_svc+0x8/0x3c0
SMP: stopping secondary CPUs
Kernel Offset: disabled
CPU features: 0x0,21806000
Memory Limit: none
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Commit 8c0e64ac40 ("thermal: armada: get rid of the ->is_valid()
pointer") removed the unnecessary indirection through a function
pointer, but in doing so, also removed the negation operator too:
- if (priv->data->is_valid && !priv->data->is_valid(priv)) {
+ if (armada_is_valid(priv)) {
which results in:
armada_thermal f06f808c.thermal: Temperature sensor reading not valid
armada_thermal f2400078.thermal: Temperature sensor reading not valid
armada_thermal f4400078.thermal: Temperature sensor reading not valid
at boot, or whenever the "temp" sysfs file is read. Replace the
negation operator.
Fixes: 8c0e64ac40 ("thermal: armada: get rid of the ->is_valid() pointer")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Sysfs interface to update cooling device cur_state does not
currently holding cooling device lock sometimes leading to
stale values in cur_state if getting updated simultanelously
from user space and thermal framework. Adding the proper locking
code fixes this issue.
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
commit ff140fea84 ("Thermal: handle thermal zone device properly
during system sleep") added PM hook to call thermal zone reset during
sleep. However resetting thermal zone will also clear the passive state
and thus cancel the polling queue which leads the passive cooling device
state not being cleared properly after sleep.
thermal_pm_notify => thermal_zone_device_reset set passive to 0
thermal_zone_trip_update will skip update passive as `old_target ==
instance->target'.
monitor_thermal_zone => thermal_zone_device_set_polling will cancel
tz->poll_queue, so the cooling device state will not be changed
afterwards.
Reported-by: Kame Wang <kamewang@google.com>
Signed-off-by: Wei Wang <wvw@google.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Pull thermal management updates from Zhang Rui:
- Fix a use-after-free issue when unregistering a thermal cooling
device (Dmitry Osipenko)
- use power_efficient_wq for thermal worker to save more power (Jeson
Gao)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: core: using power_efficient_wq for thermal worker
thermal: core: Fix use-after-free in thermal_cooling_device_destroy_sysfs
Pull thermal SoC updates from Eduardo Valentin:
"Several new things coming up. Specifics:
- Rework of tsens and hisi thermal drivers
- OF-thermal now allows sharing multiple cooling devices on maps
- Added support for r8a7744 and R8A77970 on rcar thermal driver
- Added support for r8a774a1 on rcar_gen3 thermal driver
- New thermal driver stm32
- Fixes on multiple thermal drivers: of-thermal, imx, qoriq, armada,
qcom-spmi, rcar, da9062/61"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal: (41 commits)
thermal: da9062/61: Prevent hardware access during system suspend
thermal: rcar_thermal: Prevent doing work after unbind
thermal: rcar_thermal: Prevent hardware access during system suspend
thermal: rcar_gen3_thermal: add R8A77980 support
dt-bindings: thermal: rcar-gen3-thermal: document R8A77980 bindings
thermal: add stm32 thermal driver
dt-bindings: stm32-thermal: add binding documentation
thermal: rcar_thermal: add R8A77970 support
dt-bindings: thermal: rcar-thermal: document R8A77970 bindings
thermal: rcar_thermal: fix duplicate IRQ request
dt-bindings: thermal: rcar: Add device tree support for r8a7744
thermal/drivers/hisi: Add the dual clusters sensors for hi3660
thermal/drivers/hisi: Add more sensors channel
thermal/drivers/hisi: Remove pointless irq field
thermal/drivers/hisi: Use platform_get_irq_byname
thermal/drivers/hisi: Replace macro name with relevant sensor location
thermal/drivers/hisi: Add multiple sensors support
thermal/drivers/hisi: Prepare to support multiple sensors
thermal/drivers/hisi: Factor out the probe functions
thermal/drivers/hisi: Set the thermal zone private data to the sensor pointer
...
The workqueue used for monitoring the hardware may run while the device
is already suspended. Fix this by using the freezable system workqueue
instead, cfr. commit 51e20d0e3a ("thermal: Prevent polling from
happening during system suspend").
Fixes: 608567aac3 ("thermal: da9062/61: Thermal junction temperature monitoring driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When testing bind/unbind on r8a7791/koelsch:
WARNING: CPU: 1 PID: 697 at lib/debugobjects.c:329 debug_print_object+0x8c/0xb4
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x10
This happens if the workqueue runs after the device has been unbound.
Fix this by cancelling any queued work during remove.
Fixes: e0a5172e9e ("thermal: rcar: add interrupt support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
On r8a7791/koelsch, sometimes the following message is printed during
system suspend:
rcar_thermal e61f0000.thermal: thermal sensor was broken
This happens if the workqueue runs while the device is already
suspended. Fix this by using the freezable system workqueue instead,
cfr. commit 51e20d0e3a ("thermal: Prevent polling from happening
during system suspend").
Fixes: e0a5172e9e ("thermal: rcar: add interrupt support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add the R-Car V3H (R8A77980) SoC support to the R-Car gen3 thermal driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add support for DTS thermal sensor that can be
found on some STM32 platforms.
This driver is based on OF and works in interrupt
mode.
It offers two temperature trip points:
passive and critical. The first is intended for
passive cooling notification while the second is
used for over-temperature reset.
Signed-off-by: David Hernandez Sanchez <david.hernandezsanchez@st.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add the R-Car V3M (R8A77970) SoC support to the R-Car gen2 thermal driver.
The hardware is the same as in the R-Car D3 (R8A77995) plus the CIVM status
register (we don't use).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The driver on R8A77995 requests the same IRQ twice since
platform_get_resource() is always called for the 1st IRQ resource.
Fixes: 1969d9dc20 ("thermal: rcar_thermal: add r8a77995 support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The code is ready to support multiple sensors on the hi3660. The DT
defines a thermal zone per cluster.
Add the little cluster sensor and let it bind with the thermal zone.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add the sensor channels id for the little, g3d and modem.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The irq field in the data structure is pointless as the scope of its
usage is just to request the interrupt. It can be replaced by a local
variable.
Use the 'ret' variable to get the interrupt number.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As we have the interrupt names defines, replace platform_get_irq() by
platform_get_irq_byname(), so no confusion can be made when getting
the interrupt with the sensor id.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Change the macro name in order to give a better indication of the
sensor location.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Change the code as it is dealing with several sensors.
For git-bisect compatibility (compilation and booting), assume the DT
is not yet changed and we have a single interrupt.
Next changes will support multiple interrupt sorted by their name.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Convert the 'sensor' field to a pointer and propagate the change in
the file. Havintg a pointer, gives us the opportunity to define
multiple sensors.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The hi6220 and the hi3660 probe functions are doing almost the same
operations, they can share 90% of their code.
Factor out the probe functions by moving the common code in the common
probe function.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Store the sensor pointer in the thermal zone private data and use it
in the callback functions. That allows to continue the conversion to
sensor oriented code where the pointers are the sensors.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In order to support multiple sensors, we have to change the code to
deal with sensors and not the hisi thermal structure.
Add a back pointer to the hisi thermal structure (containerof is not a
good option because later we convert the sensor field to a pointer).
Change the functions parameters to take a sensor instead of this hisi
thermal 'data' structure.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Group the temperature sensor specific ops into a single structure and
assign it to hisi thermal data structure.
Change the platform data pointer to reference the specific sensor ops
instead of the probe functions.
Moving out those allow to split the code to self-encapsulate the
sensor object.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
During probe phase, the error path can be handled in one place and
use goto method to save many duplicated code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The SROT registers are initialised by the secure firmware at boot. We
don't have write access to the registers. Check if the block is enabled
before continuing.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Registers have moved around across TSENS generations. For example, the
CTRL register was at offset 0x0 in the SROT region on msm8916 but is at
offset 0x4 in newer v2 based TSENS HW blocks.
Allow passing offsets of important registers so that we can continue to
use common functions.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
On platforms whose device trees specify two address spaces for TSENS, the
second one points to the SROT registers. Initialise the SROT map on those
platforms.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The TSENS driver currently only uses a limited set of registers from the TM
address space. So it was ok to map just that set of registers and call it
"map".
We'd now like to map a second set: SROT registers to introduce new
functionality. Rename the "map" field to a more appropriate "tm_map".
The 8960 doesn't have a clear split between TM and SROT registers. To avoid
complicating the data structure, it will switchover to using tm_map for its
maps.
There is no functional change with this patch.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
hw_id is dynamically allocated but not used anywhere. Get rid of dead
code.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The TSENS drivers use a GPL-2.0 license. Replace with equivalent SPDX
tags and delete the full license text.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We've already converted over the devicetree of platforms using v2
version of the TSENS IP to use two address spaces. Now prepare to
convert over the 8916 and 8974 platforms to use separate SROT and TM
address spaces.
This patch will work with device trees with one or two address spaces
because we set the tm_offset in commit 5b1283984f ("thermal: tsens:
Add support to split up register address space into two").
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
For SMP systems, thermal worker should use power_efficient_wq in power
saving mode, that will make scheduler more flexible on selecting an active
core for running work handler to avoid keeping work handler always
running on a single core, that will save some power.
Even if 'power_efficient_wq' relevant configs are disabled
'system_freezable_power_efficient_wq' is identical to system_freezable_wq,
behavior is unchanged.
Signed-off-by: Jeson Gao <jeson.gao@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch fixes use-after-free that was detected by KASAN. The bug is
triggered on a CPUFreq driver module unload by freeing 'cdev' on device
unregister and then using the freed structure during of the cdev's sysfs
data destruction. The solution is to unregister the sysfs at first, then
destroy sysfs data and finally release the cooling device.
Cc: <stable@vger.kernel.org> # v4.17+
Fixes: 8ea229511e ("thermal: Add cooling device's statistics in sysfs")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Going primarily by:
https://en.wikipedia.org/wiki/List_of_Intel_Atom_microprocessors
with additional information gleaned from other related pages; notably:
- Bonnell shrink was called Saltwell
- Moorefield is the Merriefield refresh which makes it Airmont
The general naming scheme is: FAM6_ATOM_UARCH_SOCTYPE
for i in `git grep -l FAM6_ATOM` ; do
sed -i -e 's/ATOM_PINEVIEW/ATOM_BONNELL/g' \
-e 's/ATOM_LINCROFT/ATOM_BONNELL_MID/' \
-e 's/ATOM_PENWELL/ATOM_SALTWELL_MID/g' \
-e 's/ATOM_CLOVERVIEW/ATOM_SALTWELL_TABLET/g' \
-e 's/ATOM_CEDARVIEW/ATOM_SALTWELL/g' \
-e 's/ATOM_SILVERMONT1/ATOM_SILVERMONT/g' \
-e 's/ATOM_SILVERMONT2/ATOM_SILVERMONT_X/g' \
-e 's/ATOM_MERRIFIELD/ATOM_SILVERMONT_MID/g' \
-e 's/ATOM_MOOREFIELD/ATOM_AIRMONT_MID/g' \
-e 's/ATOM_DENVERTON/ATOM_GOLDMONT_X/g' \
-e 's/ATOM_GEMINI_LAKE/ATOM_GOLDMONT_PLUS/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: dave.hansen@linux.intel.com
Cc: len.brown@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull thermal fixes from Eduardo Valentin:
"Minor fixes to OF thermal, qoriq, and rcar drivers"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: of-thermal: disable passive polling when thermal zone is disabled
thermal: rcar_gen3_thermal: convert to SPDX identifiers
thermal: rcar_thermal: convert to SPDX identifiers
thermal: qoriq: Switch to SPDX identifier
thermal: qoriq: Simplify the 'site' variable assignment
thermal: qoriq: Use devm_thermal_zone_of_sensor_register()
A cooling map entry may now contain a list of phandles and their
arguments representing multiple devices which share the trip point.
This patch updates the thermal OF core to parse them properly. The trip
point and contribution value is shared by multiple cooling devices now
and so a new structure is created, struct __thermal_cooling_bind_param,
which represents a cooling device and its min/max states and the
existing struct __thermal_bind_params now contains an array of this new
cooling device structure.
Tested on Hikey960.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There are three thermal stages defined in the PMIC:
stage 1: warning
stage 2: system should shut down
stage 3: emergency shut down
By default the PMIC assumes that the OS isn't doing anything and thus
at stage 2 it does a partial PMIC shutdown and at stage 3 it kills
all power. When switching between thermal stages the PMIC generates an
interrupt which is handled by the driver. The partial PMIC shutdown at
stage 2 can be disabled by software, which allows the OS to initiate a
shutdown at stage 2 with a thermal zone configured accordingly.
If a critical trip point is configured in the thermal zone the driver
adjusts the stage 1-3 temperature thresholds to (closely) match the
critical temperature with a stage 2 threshold (125/130/135/140 °C).
If a suitable match is found the partial shutdown at stage 2 is
disabled. If for some reason the system doesn't shutdown at stage 2
the emergency shutdown at stage 3 kicks in.
The partial shutdown at stage 2 remains enabled in these cases:
- no critical trip point defined
- the temperature of the critical trip point is < 125°C
- the temperature of the critical trip point is > 140°C and no
ADC channel is configured (thus the OS is not notified when the critical
temperature is reached)
Suggested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Pull thermal management updates from Zhang Rui:
- Add Daniel Lezcano as the reviewer of thermal framework and SoC
driver changes (Daniel Lezcano).
- Fix a bug in intel_dts_soc_thermal driver, which does not translate
IO-APIC GSI (Global System Interrupt) into Linux irq number (Hans de
Goede).
- For device tree bindings, allow cooling devices sharing same trip
point with same contribution value to share cooling map (Viresh
Kumar).
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
dt-bindings: thermal: Allow multiple devices to share cooling map
MAINTAINERS: Add Daniel Lezcano as designated reviewer for thermal
Thermal: Intel SoC DTS: Translate IO-APIC GSI number to linux irq number
Also add these typos to spelling.txt so checkpatch.pl will look for them.
Link: http://lkml.kernel.org/r/88af06b9de34d870cb0afc46cfd24e0458be2575.1529471371.git.fthain@telegraphics.com.au
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When thermal zone is in passive mode, disabling its mode from
sysfs is NOT taking effect at all, it is still polling the
temperature of the disabled thermal zone and handling all thermal
trips, it makes user confused. The disabling operation should
disable the thermal zone behavior completely, for both active and
passive mode, this patch clears the passive_delay when thermal
zone is disabled and restores it when it is enabled.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As original license mentioned, it is GPL-2.0 in SPDX.
Then, MODULE_LICENSE() should be "GPL v2" instead of "GPL".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There is no need to assign zero to the variable 'site' and then
perform a compound bitwise OR operation afterwards.
Make it simpler by assigning the final 'site' value directly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
By using the managed devm_thermal_zone_of_sensor_register() we can
drop the explicit call to thermal_zone_of_sensor_unregister() in the
qoriq_tmu_remove() function, which simplifies the code a bit.
So switch to devm_thermal_zone_of_sensor_register().
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Pull thermal management updates from Eduardo Valentin:
- rework tsens driver to add support for tsens-v2 (Amit Kucheria)
- rework armada thermal driver to use syscon and multichannel support
(Miquel Raynal)
- fixes to TI SoC, IMX, Exynos, RCar, and hwmon drivers
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal: (34 commits)
thermal: armada: fix copy-paste error in armada_thermal_probe()
thermal: rcar_thermal: avoid NULL dereference in absence of IRQ resources
thermal: samsung: Remove Exynos5440 clock handling left-overs
thermal: tsens: Fix negative temperature reporting
thermal: tsens: switch from of_iomap() to devm_ioremap_resource()
thermal: tsens: Rename variable
thermal: tsens: Add generic support for TSENS v2 IP
thermal: tsens: Rename tsens-8996 to tsens-v2 for reuse
thermal: tsens: Add support to split up register address space into two
dt: thermal: tsens: Document the fallback DT property for v2 of TSENS IP
thermal: tsens: Get rid of unused fields in structure
thermal_hwmon: Pass the originating device down to hwmon_device_register_with_info
thermal_hwmon: Sanitize attribute name passed to hwmon
dt-bindings: thermal: armada: add reference to new bindings
dt-bindings: cp110: add the thermal node in the syscon file
dt-bindings: cp110: update documentation since DT de-duplication
dt-bindings: ap806: add the thermal node in the syscon file
dt-bindings: cp110: prepare the syscon file to list other syscons nodes
dt-bindings: ap806: prepare the syscon file to list other syscons nodes
dt-bindings: cp110: rename cp110 syscon file
...
The return value from devm_kzalloc() is not checked correctly. The
test is done against a wrong variable. Fix it.
Fixes: e72f03ef2543 ("thermal: armada: use the resource managed registration helper alternative")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Ensure that the base address used by a call to rcar_thermal_common_write()
may be NULL if the SOC supports interrupts for use with the thermal device
but none are defined in DT as is the case for R-Car H1 (r8a7779). Guard
against this condition to prevent a NULL dereference when the device is
probed.
Tested on:
* R-Mobile APE6 (r8a73a4) / APE6EVM
* R-Car H1 (r8a7779) / Marzen
* R-Car H2 (r8a7790) / Lager
* R-Car M2-W (r8a7791) / Koelsch
* R-Car M2-N (r8a7793) / Gose
* R-Car D3 ES1.0 (r8a77995) / Draak
Fixes: 1969d9dc20 ("thermal: rcar_thermal: add r8a77995 support")
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Commit 8014220d48 ("thermal: samsung: Remove support for Exynos5440")
removed the Exynos5440 specific part of code for accessing TMU interrupt
registers but the surrounding clock handling was left.
Clean it up.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The current code will always return 0xffffffff in case of negative
temperatures due to a bug in how the binary sign extension is being done.
Use sign_extend32() instead.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
devm_ioremap_resources() automatically requests resources (so that the I/O
region shows up in /proc/iomem) and devm_ wrappers do better error handling
and unmapping of the I/O region when needed.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We're actually reading the temperature from the status register. Fix the
variable name to reflect that.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
SDM845 uses v2 of the TSENS IP block but the get_temp() function appears to
be identical across v2.x.y in code seen so far. We use the generic
get_temp() function defined as part of ops_generic_v2.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The TSENS block inside the 8996 is internally classified as version 2 of
the IP. Several other SoC families use this block and can share this code.
We rename get_temp() to reflect that it can be used across the v2 family.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There are two banks of registers for v2 TSENS IPs: SROT and TM. On older
SoCs these were contiguous, leading to DTs mapping them as one register
address space of size 0x2000. In newer SoCs, these two banks are not
contiguous anymore.
Add logic to init_common() to differentiate between old and new DTs and
adjust associated offsets for the TM register bank so that the old DTs will
continue to function correctly.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
status_field and trdy are unused in any of the tsens drivers. Remove them.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rajendra Nayak <rnayak@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When registering the hwmon device, we pass NULL as the device.
While this doesn't result in any immediate breakage, it leaves
the hwmon device at the root of the virtual devices, rather than
attached to the thermal zone hierarchy.
Instead, let's pass the actual device, which is part of the
thermal_zone_device structure. This also avoids the rather
unpleasant ""NULL device *" which can be generated by dev_{err,info}
in the hwmon subsystem.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
My Chromebook Plus (kevin) is spitting the following at boot time:
(NULL device *): hwmon: 'sbs-9-000b' is not a valid name attribute, please fix
Clearly, __hwmon_device_register is unhappy about the property name.
Some investigation reveals that thermal_add_hwmon_sysfs doesn't
sanitize the name of the attribute.
In order to keep it quiet, let's replace '-' with '_' in hwmon->type
This is consistent with what iio-hwmon does since b92fe9e337.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The implementation of armada_is_valid() is very simple and is the same
across all the versions of the IP since the ->is_valid_bit has been
introduced. Simplify the structure by getting rid of the function
pointer and calling directly the function.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Sensor selection when using multiple sensors already checks for the
sensor validity. Move it to the legacy ->get_temp() hook, where it is
still needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
When using new bindings with multiple sensors, sensor validity is
checked twice because sensor selection also checks for the validity.
Remove the redundant call from the IP initialization helper and move it
to the legacy probe section where it is still needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
MVEBU thermal IP supports multiple channels. Each channel may have
several sensors but for now each channel is wired to only one thermal
sensor. The first channel always points to the so called internal
sensor, within the thermal IP. There is usually one more channel (with
one sensor each time) per CPU. The code has been written to support
possible evolutions of the ap806 IP that would embed more CPUs and thus
more channels to select. Each channel should be referenced in the device
tree as an independent thermal zone.
Add the possibility to read each of these sensors through sysfs by
registering all the sensors (translated in "thermal_zone"). Also add a
mutex on these accesses to avoid read conflicts (only one channel/sensor
may be selected and read at a time).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Current use of thermal_zone_device_register() triggers a warning at boot
and should be replaced by devm_thermal_zone_of_sensor_register(). This
allows better handling of multiple thermal zones for later multi-sensors
support.
Also change the driver data to embed a new structure to make the
difference between legacy data (which needs to be cleaned) and
syscon-related data.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Until recently, only one register was referenced in MVEBU thermal IP
node. Recent changes added a second entry pointing to another
register right next to it. We cannot know for sure that we will not
have to access other registers. That will be actually the case when
overheat interrupt feature will come, where it will be needed to access
DFX registers in the same area.
This approach is not scalable so instead of adding consinuously memory
areas in the DT (and change the DT bindings, while keeping backward
compatibility), move the thermal node into a wider syscon from which it
will be possible to also configure the thermal interrupt.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Configure the sample frequency and number of averaged samples.
This is needed for two reasons:
1/ To be bootloader independent.
2/ To prepare the introduction of multi-sensors support by preventing
inconsistencies when reading temperatures that could be a mean of
samples took from different sensors.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Until now, Armada 380 and CP110 could share the same ->init() function
because their use was identical.
Prepare the support of multi-sensors support and overheat interrupt
feature by separating the initialization paths before they actually
diverge.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Calling a hook ->init_sensor() while what is initialized is the IP
itself and not the sensors is misleading. Rename the hook ->init() to
avoid any confusion in later work bringing multi-sensors support.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
On older versions of this thermal IP, TSEN referred as the internal
sensor in the thermal IP while EXT_TSEN referred as sensors outside of
this IP, ie in the CPUs most of the time. The bit names in the
specifications do not follow this rule anymore, so remove these comments
that are misleading.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Prepare the migration to use regmaps by first simplifying the
initialization functions: avoid unnecessary write/read cycles on
configuration registers.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Thermal zone names must follow certain rules imposed by the framework.
They are limited in length and shall not have any hyphen '-'.
This is done in a separate function for future use in another location.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Majority of this code (i.e. functions from ti-bandgap.c) has been
introduced in May 2013 by commit eb982001db ("thermal: introduce TI
SoC thermal driver"). Just remove it altogether (in case it is needed
it can be easily resurrected from git repo).
While at it fix incorrect "not used" comments.
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The Intel SoC DTS uses a hardcoded GSI number, before this commit
it was passing it to request_irq as if it were a linux irq number,
but there is no 1:1 mapping so in essence it was requesting a
random interrupt.
Besides this causing the DTS driver to not actually get an interrupt
if the thermal thresholds are exceeded this also is causing an
interrupt conflict on some devices since the linux irq 86 which is
being requested is already in use, leading to oopses like this:
genirq: Flags mismatch irq 86. 00002001 (soc_dts) vs. 00000083 (volume_down)
CPU: 0 PID: 601 Comm: systemd-udevd Tainted: G C OE 4.17.0-rc6+ #45
Hardware name: Insyde i86/Type2 - Board Product Name, BIOS CHUWI.D86JLBNR03 01/14/2015
Call Trace:
dump_stack+0x5c/0x80
__setup_irq.cold.50+0x4e/0xac
? request_threaded_irq+0xad/0x160
request_threaded_irq+0xf5/0x160
? 0xffffffffc0a93000
intel_soc_thermal_init+0x74/0x1000 [intel_soc_dts_thermal]
This commit makes the intel_soc_dts_thermal.c code call
acpi_register_gsi() to translate the hardcoded IO-APIC GSI number (86)
to a linux irq, so that the dts code uses the right interrupt and we
no longer get an oops about an irq conflict.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Without this fix, the thermal probe on i.MX6 might trigger a division
by zero exception later in the probe if the calibration does fail.
Note: This linux behavior (Division by zero in kernel) has been triggered
on a Qemu i.MX6 emulation where parameters in nvmem were not set. With this
fix the division by zero is not triggeed anymore as the thermal probe does
fail early.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The cooling device should be part of the i.MX cpufreq driver, but it
cannot be removed for the sake of DT stability. So turn the cooling
device registration into a separate function and perform the
registration only if the CPU OF node does not have the #cooling-cells
property.
Use of_cpufreq_power_cooling_register in imx_thermal code to link the
cooling device to the device tree node provided.
This makes it possible to bind the cpufreq cooling device to a custom
thermal zone via a cooling-maps entry like:
cooling-maps {
map0 {
trip = <&board_alert>;
cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
Assuming a cpu node exists with label "cpu0" and #cooling-cells
property.
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=zUUp
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull more overflow updates from Kees Cook:
"The rest of the overflow changes for v4.18-rc1.
This includes the explicit overflow fixes from Silvio, further
struct_size() conversions from Matthew, and a bug fix from Dan.
But the bulk of it is the treewide conversions to use either the
2-factor argument allocators (e.g. kmalloc(a * b, ...) into
kmalloc_array(a, b, ...) or the array_size() macros (e.g. vmalloc(a *
b) into vmalloc(array_size(a, b)).
Coccinelle was fighting me on several fronts, so I've done a bunch of
manual whitespace updates in the patches as well.
Summary:
- Error path bug fix for overflow tests (Dan)
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed
(Kees)"
* tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (26 commits)
treewide: Use array_size in f2fs_kvzalloc()
treewide: Use array_size() in f2fs_kzalloc()
treewide: Use array_size() in f2fs_kmalloc()
treewide: Use array_size() in sock_kmalloc()
treewide: Use array_size() in kvzalloc_node()
treewide: Use array_size() in vzalloc_node()
treewide: Use array_size() in vzalloc()
treewide: Use array_size() in vmalloc()
treewide: devm_kzalloc() -> devm_kcalloc()
treewide: devm_kmalloc() -> devm_kmalloc_array()
treewide: kvzalloc() -> kvcalloc()
treewide: kvmalloc() -> kvmalloc_array()
treewide: kzalloc_node() -> kcalloc_node()
treewide: kzalloc() -> kcalloc()
treewide: kmalloc() -> kmalloc_array()
mm: Introduce kvcalloc()
video: uvesafb: Fix integer overflow in allocation
UBIFS: Fix potential integer overflow in allocation
leds: Use struct_size() in allocation
Convert intel uncore to struct_size
...
Pull thermal SoC updates from Zhang Rui:
"Thermal SoC management updates:
- imx thermal driver now supports i.MX7 thermal sensor (Anson Huang)
- exynos thermal driver dropped support for exynos 5440 (Krzysztof
Kozlowski)
- rcar_thermal now supports r8a77995 (Yoshihiro Kaneko)
- rcar_gen3_thermal now supports r8a77965 (Niklas Söderlund)
- qcom-spmi-temp-alarm now supports GEN2 PMIC peripherals (David
Collins)
- uniphier thermal now supports UniPhier PXs3 (Kunihiko Hayashi)
- mediatek thermal now supports MT7622 SoC (Sean Wang)
- considerable refactoring of exynos driver (Bartlomiej
Zolnierkiewicz)
- small fixes all over the place on different drivers"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal: (50 commits)
thermal: qcom: tsens: Allow number of sensors to come from DT
thermal: tegra: soctherm: add const to struct thermal_cooling_device_ops
thermal: exynos: Reduce severity of too early temperature read
thermal: imx: Switch to SPDX identifier
thermal: qcom-spmi-temp-alarm: add support for GEN2 PMIC peripherals
thermal: ti-soc-thermal: fix incorrect entry in omap5430_adc_to_temp[]
thermal: rcar_thermal: add r8a77995 support
dt-bindings: thermal: rcar-thermal: add R8A77995 support
thermal: mediatek: use of_device_get_match_data()
thermal: exynos: remove trip reporting to user-space
thermal: exynos: remove unused defines for Exynos5433
thermal: exynos: cleanup code for enabling threshold interrupts
thermal: exynos: check return values of ->get_trip_[temp, hyst] methods
thermal: exynos: move trips setting to exynos_tmu_initialize()
thermal: exynos: set trips in ascending order in exynos7_tmu_initialize()
thermal: exynos: do not use trips structure directly in ->tmu_initialize
thermal: exynos: add exynos*_tmu_set_[trip,hyst]() helpers
thermal: exynos: move IRQs clearing to exynos_tmu_initialize()
thermal: exynos: clear IRQs later in exynos4412_tmu_initialize()
thermal: exynos: make ->tmu_initialize method void
...
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=/3L8
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull overflow updates from Kees Cook:
"This adds the new overflow checking helpers and adds them to the
2-factor argument allocators. And this adds the saturating size
helpers and does a treewide replacement for the struct_size() usage.
Additionally this adds the overflow testing modules to make sure
everything works.
I'm still working on the treewide replacements for allocators with
"simple" multiplied arguments:
*alloc(a * b, ...) -> *alloc_array(a, b, ...)
and
*zalloc(a * b, ...) -> *calloc(a, b, ...)
as well as the more complex cases, but that's separable from this
portion of the series. I expect to have the rest sent before -rc1
closes; there are a lot of messy cases to clean up.
Summary:
- Introduce arithmetic overflow test helper functions (Rasmus)
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)"
* tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
treewide: Use struct_size() for devm_kmalloc() and friends
treewide: Use struct_size() for vmalloc()-family
treewide: Use struct_size() for kmalloc()-family
device: Use overflow helpers for devm_kmalloc()
mm: Use overflow helpers in kvmalloc()
mm: Use overflow helpers in kmalloc_array*()
test_overflow: Add memory allocation overflow tests
overflow.h: Add allocation size calculation helpers
test_overflow: Report test failures
test_overflow: macrofy some more, do more tests for free
lib: add runtime test of check_*_overflow functions
compiler.h: enable builtin overflow checkers and add fallback code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=hB2y
-----END PGP SIGNATURE-----
Merge tag 'printk-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk
Pull printk updates from Petr Mladek:
- Help userspace log daemons to catch up with a flood of messages. They
will get woken after each message even if the console is far behind
and handled by another process.
- Flush printk safe buffers safely even when panic() happens in the
normal context.
- Fix possible va_list reuse when race happened in printk_safe().
- Remove %pCr printf format to prevent sleeping in the atomic context.
- Misc vsprintf code cleanup.
* tag 'printk-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
printk: drop in_nmi check from printk_safe_flush_on_panic()
lib/vsprintf: Remove atomic-unsafe support for %pCr
serial: sh-sci: Stop using printk format %pCr
thermal: bcm2835: Stop using printk format %pCr
clk: renesas: cpg-mssr: Stop using printk format %pCr
printk: fix possible reuse of va_list variable
printk: wake up klogd in vprintk_emit
vsprintf: Tweak pF/pf comment
lib/vsprintf: Mark expected switch fall-through
lib/vsprintf: Replace space with '_' before crng is ready
lib/vsprintf: Deduplicate pointer_string()
lib/vsprintf: Move pointer_string() upper
lib/vsprintf: Make flag_spec global
lib/vsprintf: Make strspec global
lib/vsprintf: Make dec_spec global
lib/test_printf: Mark big constant with UL
Printk format "%pCr" will be removed soon, as clk_get_rate() must not be
called in atomic context.
Replace it by printing the variable that already holds the clock rate.
Note that calling clk_get_rate() is safe here, as the code runs in task
context.
Link: http://lkml.kernel.org/r/1527845302-12159-3-git-send-email-geert+renesas@glider.be
To: Jia-Ju Bai <baijiaju1990@gmail.com>
To: Jonathan Corbet <corbet@lwn.net>
To: Michael Turquette <mturquette@baylibre.com>
To: Stephen Boyd <sboyd@kernel.org>
To: Zhang Rui <rui.zhang@intel.com>
To: Eduardo Valentin <edubezval@gmail.com>
To: Eric Anholt <eric@anholt.net>
To: Stefan Wahren <stefan.wahren@i2se.com>
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-doc@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
For platforms that has multiple copies of the TSENS hardware block it's
necessary to be able to specify the number of sensors per block in DeviceTree.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Correct the typecast with const to struct thermal_cooling_device_ops.
It is the last argument to the function thermal_of_cooling_device_register
and this argument is of type const. So, declare this structure
thermal_cooling_device_ops as constant.
Signed-off-by: sumeet p <srplinux2008@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Thermal core tries to read temperature during sensor registering in
thermal_zone_of_sensor_register(). In that time Exynos TMU driver and
hardware are not yet initialized. Commit 0eb875d88a ("thermal:
exynos: Reading temperature makes sense only when TMU is turned on")
added a boolean flag to prevent reading bogus temperature in such
case but it exposed warning message during boot:
[ 3.864913] thermal thermal_zone0: failed to read out thermal zone (-22)
Return EAGAIN in such case to skip omitting such message because it
might mislead user.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add support for the TEMP_ALARM GEN2 PMIC peripheral subtype. The
GEN2 subtype defines an over temperature state with hysteresis
instead of stage in the status register. There are two GEN2
states corresponding to stages 1 and 2.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Entry for Index 941 has one zero too much. Fix it.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Wei Ni
Michael Kao
Yuantian Tang
Pramod Kumar
Amit Kucheria
Linus Torvalds
Aaron Hill
Sinan Kaya
Dan Carpenter
Stephen Rothwell
Bjorn Andersson
Yoshihiro Kaneko
Fabrizio Castro
Miquel Raynal
Arnd Bergmann
Kunihiko Hayashi
Yangtao Li
Anson Huang
Srinivas Kandagatla
YueHaibing
Julia Lawall
Matthias Brugger
Eduardo Valentin
Masahiro Yamada
David HERNANDEZ SANCHEZ
Daniel Lezcano
Zhang Rui
Stefan Wahren
Russell King
Thara Gopinath
Wei Wang
Wolfram Sang
Lukasz Luba
Geert Uytterhoeven
Sergei Shtylyov
Rob Herring
Jeson Gao
Dmitry Osipenko
Peter Zijlstra
Viresh Kumar
Matthias Kaehlcke
Finn Thain
Kuninori Morimoto
Fabio Estevam
Wei Yongjun
Simon Horman
Krzysztof Kozlowski
Marc Zyngier
Bartlomiej Zolnierkiewicz
Hans de Goede
Jean-Christophe Dubois
Bastian Stender
Kees Cook
srplinux2008
David Collins
Sumeet Pawnikar