Move iop33x and iop32x PCI to fixed i/o mapping and remove io.h. This
changes the PCI bus addresses from the cpu address to 0 based. It appears
that there is translation h/w for this, but its untested.
Not sure what to do with io_offset. I think it should always be 0.
AFAICT, PCI setup is skipped if the ATU is already setup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move mv78xx0 PCI to fixed i/o mapping and remove io.h. This changes the PCI
bus addresses from the cpu address to 0 based. It appears that there is
translation h/w for this, but its untested.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move iop13xx PCI to fixed i/o mapping and remove io.h.
This changes the PCIe bus address to start at 0x10000. Let's hope this
works. If it does not, the alternative would be to revert the value we
write into OIOTVR to zero and set sys->io_offset to 64K.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
iop13xx confuses I/O port numbers with physical addresses, which breaks
legacy ISA I/O access behind PCI bridges and makes it unnecessarily hard
to unify the inb/outb accessors with other platforms. This removes the
special-casing and just puts all I/O ports into a single 128KB virtually
mapped I/O port range starting at port zero.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Move orion5x PCI to fixed i/o mapping and remove io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move kirkwood PCI to fixed i/o mapping and remove io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
The i/o regions are changed from 1MB to 64KB. It's likely that the 2nd
bus is not setup correctly.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move footbridge PCI to fixed i/o mapping. io.h is still needed for the
!MMU case.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Convert shark to use the fixed i/o mapping and remove io.h.
This shrinks the mapping from 256MB to 1MB, but nothing is using that much
space AFAICT.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Move tegra PCI to fixed i/o mapping and remove io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Colin Cross <ccross@android.com>
Cc: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
With consolidation of the PCI i/o mappings, the i/o space is being
set to start at a PCI bus addr of 0x0 and fixed to 64K per bus. In
this case the core ARM PCI setup code can setup the i/o resource.
Currently, the resource is only setup if the platform did not setup
an i/o resource.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
This adds a fixed virtual mapping for PCI i/o addresses. The mapping is
located at the last 2MB of vmalloc region (0xfee00000-0xff000000). 2MB
is used to align with PMD size, but IO_SPACE_LIMIT is 1MB. The space
is reserved after .map_io and can be mapped at any time later with
pci_ioremap_io. Platforms which need early i/o mapping (e.g. for vga
console) can call pci_map_io_early in their .map_io function.
This has changed completely from the 1st implementation which only
supported creating the static mapping at .map_io.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Nicolas Pitre <nico@linaro.org>
Instead of using the custom iop3xx gpio functions, use the gpiolib
variants. This should be functionally the same since the gpiolib
just calls the iop3xx gpio functions. This is needed in preparation
of removing iop3xx mach/io.h headers.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: "Jean Delvare (PC drivers, core)" <khali@linux-fr.org>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: linux-i2c@vger.kernel.org
The idr_pre_get() function never returns a value < 0. It returns 0 (no
memory) or 1 (OK).
Reported-by: Silva Paulo <psdasilva@yahoo.com>
[ Rewrote Silva's patch, but attributing it to Silva anyway - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Containing the regression fixes for USB-audio due to the transition to
the new streaming logic, mostly found on Logitech webcams.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=W7/C
-----END PGP SIGNATURE-----
Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Containing the regression fixes for USB-audio due to the transition to
the new streaming logic, mostly found on Logitech webcams."
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: snd-usb: move calls to usb_set_interface
ALSA: usb-audio: Fix the first PCM interface assignment
Pull ACPI patch from Len Brown.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
ACPICA: Fix possible fault in return package object repair code
vsyscall_seccomp introduced a dependency on __secure_computing. On
configurations with CONFIG_SECCOMP disabled, compilation will fail.
Reported-by: feng xiangjun <fengxj325@gmail.com>
Signed-off-by: Will Drewry <wad@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a regression preventing the ACPI cpufreq driver from loading on some
systems where it worked previously without any problems.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=XZHs
-----END PGP SIGNATURE-----
Merge tag 'cpufreq-for-3.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull cpufreq fix from Rafael Wysocki:
"This fixes a regression preventing the ACPI cpufreq driver from
loading on some systems where it worked previously without any
problems."
* tag 'cpufreq-for-3.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq / ACPI: Fix not loading acpi-cpufreq driver regression
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Oxb4
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Samsung SoC fixes from Arnd Bergmann.
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: S3C24XX: Correct CAMIF interrupt definitions
ARM: S3C24XX: Correct AC97 clock control bit for S3C2440
ARM: SAMSUNG: fix race in s3c_adc_start for ADC
ARM: SAMSUNG: Update default rate for xusbxti clock
ARM: EXYNOS: register devices in 'need_restore' state for pm_domains
ARM: EXYNOS: read initial state of power domain from hw registers
Pull RCU, perf, and scheduler fixes from Ingo Molnar.
The RCU fix is a revert for an optimization that could cause deadlocks.
One of the scheduler commits (164c33c6ad "sched: Fix fork() error path
to not crash") is correct but not complete (some architectures like Tile
are not covered yet) - the resulting additional fixes are still WIP and
Ingo did not want to delay these pending fixes. See this thread on
lkml:
[PATCH] fork: fix error handling in dup_task()
The perf fixes are just trivial oneliners.
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "rcu: Move PREEMPT_RCU preemption to switch_to() invocation"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf kvm: Fix segfault with report and mixed guestmount use
perf kvm: Fix regression with guest machine creation
perf script: Fix format regression due to libtraceevent merge
ring-buffer: Fix accounting of entries when removing pages
ring-buffer: Fix crash due to uninitialized new_pages list head
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
MAINTAINERS/sched: Update scheduler file pattern
sched/nohz: Rewrite and fix load-avg computation -- again
sched: Fix fork() error path to not crash
Fixes a problem that can occur when a lone package object is
wrapped with an outer package object in order to conform to
the ACPI specification. Can affect these predefined names:
_ALR,_MLS,_PSS,_TRT,_TSS,_PRT,_HPX,_DLM,_CSD,_PSD,_TSD
https://bugzilla.kernel.org/show_bug.cgi?id=44171
This problem was introduced in 3.4-rc1 by commit
6a99b1c94d
(ACPICA: Object repair code: Support to add Package wrappers)
Reported-by: Vlastimil Babka <caster@gentoo.org>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Cc: <stable@vger.kernel.org> # 3.4
Signed-off-by: Len Brown <len.brown@intel.com>
From Kukjin Kim <kgene.kim@samsung.com>:
* 'v3.5-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C24XX: Correct CAMIF interrupt definitions
ARM: S3C24XX: Correct AC97 clock control bit for S3C2440
ARM: SAMSUNG: fix race in s3c_adc_start for ADC
ARM: SAMSUNG: Update default rate for xusbxti clock
ARM: EXYNOS: register devices in 'need_restore' state for pm_domains
ARM: EXYNOS: read initial state of power domain from hw registers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull the leap second fixes from Thomas Gleixner:
"It's a rather large series, but well discussed, refined and reviewed.
It got a massive testing by John, Prarit and tip.
In theory we could split it into two parts. The first two patches
f55a6faa3843: hrtimer: Provide clock_was_set_delayed()
4873fa070ae8: timekeeping: Fix leapsecond triggered load spike issue
are merely preventing the stuff loops forever issues, which people
have observed.
But there is no point in delaying the other 4 commits which achieve
full correctness into 3.6 as they are tagged for stable anyway. And I
rather prefer to have the full fixes merged in bulk than a "prevent
the observable wreckage and deal with the hidden fallout later"
approach."
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hrtimer: Update hrtimer base offsets each hrtimer_interrupt
timekeeping: Provide hrtimer update function
hrtimers: Move lock held region in hrtimer_interrupt()
timekeeping: Maintain ktime_t based offsets for hrtimers
timekeeping: Fix leapsecond triggered load spike issue
hrtimer: Provide clock_was_set_delayed()
If a seccomp filter program is installed, older static binaries and
distributions with older libc implementations (glibc 2.13 and earlier)
that rely on vsyscall use will be terminated regardless of the filter
program policy when executing time, gettimeofday, or getcpu. This is
only the case when vsyscall emulation is in use (vsyscall=emulate is the
default).
This patch emulates system call entry inside a vsyscall=emulate by
populating regs->ax and regs->orig_ax with the system call number prior
to calling into seccomp such that all seccomp-dependencies function
normally. Additionally, system call return behavior is emulated in line
with other vsyscall entrypoints for the trace/trap cases.
[ v2: fixed ip and sp on SECCOMP_RET_TRAP/TRACE (thanks to luto@mit.edu) ]
Reported-and-tested-by: Owen Kibel <qmewlo@gmail.com>
Signed-off-by: Will Drewry <wad@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Please pull one hwmon subsystem fix from Jean Delvare.
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (it87) Preserve configuration register bits on init
This can be trivially triggered from userspace by passing in something unexpected.
kernel BUG at fs/locks.c:1468!
invalid opcode: 0000 [#1] SMP
RIP: 0010:generic_setlease+0xc2/0x100
Call Trace:
__vfs_setlease+0x35/0x40
fcntl_setlease+0x76/0x150
sys_fcntl+0x1c6/0x810
system_call_fastpath+0x1a/0x1f
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: stable@kernel.org # 3.2+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull input layer fixes from Dmitry Torokhov:
"The changes are limited to adding new VID/PID combinations to drivers
to enable support for new versions of hardware, most notably hardware
found in new MacBook Pro Retina boxes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - add Andamiro Pump It Up pad
Input: xpad - add signature for Razer Onza Tournament Edition
Input: xpad - handle all variations of Mad Catz Beat Pad
Input: bcm5974 - Add support for 2012 MacBook Pro Retina
HID: add support for 2012 MacBook Pro Retina
Pull media fixes from Mauro Carvalho Chehab:
- Some regression fixes at the audio part for devices with
cx23885/cx25840
- A DMA corruption fix at cx231xx
- two fixes at the winbond IR driver
- Several fixes for the EXYNOS media driver (s5p)
- two fixes at the OMAP3 preview driver
- one fix at the dvb core failure path
- an include missing (slab.h) at smiapp-core causing compilation
breakage
- em28xx was not loading the IR driver driver anymore.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (31 commits)
[media] Revert "[media] V4L: JPEG class documentation corrections"
[media] s5p-fimc: Add missing FIMC-LITE file operations locking
[media] omap3isp: preview: Fix contrast and brightness handling
[media] omap3isp: preview: Fix output size computation depending on input format
[media] winbond-cir: Initialise timeout, driver_type and allowed_protos
[media] winbond-cir: Fix txandrx module info
[media] cx23885: Silence unknown command warnings
[media] cx23885: add support for HVR-1255 analog (cx23888 variant)
[media] cx23885: make analog support work for HVR_1250 (cx23885 variant)
[media] cx25840: fix vsrc/hsrc usage on cx23888 designs
[media] cx25840: fix regression in HVR-1800 analog audio
[media] cx25840: fix regression in analog support hue/saturation controls
[media] cx25840: fix regression in HVR-1800 analog support
[media] s5p-mfc: Fixed setup of custom controls in decoder and encoder
[media] cx231xx: don't DMA to random addresses
[media] em28xx: fix em28xx-rc load
[media] dvb-core: Release semaphore on error path dvb_register_device()
[media] s5p-fimc: Stop media entity pipeline if fimc_pipeline_validate fails
[media] s5p-fimc: Fix compiler warning in fimc-lite.c
[media] s5p-fimc: media_entity_pipeline_start() may fail
...
- Revert a patch that made failing to select power class fatal;
it turns out that it fails non-fatally on Tegra boards.
Regression against 3.5-rc1.
- Add the IRQF_ONESHOT flag to the cd-gpio driver, which turned
into a regression in 3.5-rc1 when IRQF_ONESHOT became required
for threaded IRQs with no handler.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lLEH
-----END PGP SIGNATURE-----
Merge tag 'mmc-fixes-for-3.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- Revert a patch that made failing to select power class fatal;
it turns out that it fails non-fatally on Tegra boards.
Regression against 3.5-rc1.
- Add the IRQF_ONESHOT flag to the cd-gpio driver, which turned
into a regression in 3.5-rc1 when IRQF_ONESHOT became required
for threaded IRQs with no handler.
* tag 'mmc-fixes-for-3.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: cd-gpio: pass IRQF_ONESHOT to request_threaded_irq()
mmc: core: Revert "skip card initialization if power class selection fails"
- fix 'sparse warning fix' regression which totally breaks MXC NAND
- fix GPMI NAND regression when used with UBI
- update/correct sysfs documentation for new 'bitflip_threshold' field
- fix nandsim build failure
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk/+eiEACgkQdwG7hYl686NzvwCglK7p8xzqxwIUx/kCWlGqPZFr
3CsAoKf9EplTp2PvTbgyEn8+Zg+pgP/Z
=YwDa
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20120712' of git://git.infradead.org/linux-mtd
Pull late MTD fixes from David Woodhouse:
- fix 'sparse warning fix' regression which totally breaks MXC NAND
- fix GPMI NAND regression when used with UBI
- update/correct sysfs documentation for new 'bitflip_threshold' field
- fix nandsim build failure
* tag 'for-linus-20120712' of git://git.infradead.org/linux-mtd:
mtd: nandsim: don't open code a do_div helper
mtd: ABI documentation: clarification of bitflip_threshold
mtd: gpmi-nand: fix read page when reading to vmalloced area
mtd: mxc_nand: use 32bit copy functions
- 3 Palmas fixes, 1 of them being a build error fix.
- 2 mc13xx fixes. 1 for fixing an SPI regmap configuration and another one for
working around an i.Mx hardware bug.
- 1 omap-usb regression fix.
- 1 twl6040 build breakage fix.
- 1 file deletion (ab5500-core.h) that was overlooked during the last merge
window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=dlI4
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD Fixes from Samuel Ortiz:
- Three Palmas fixes, One of them being a build error fix.
- Two mc13xx fixes. One for fixing an SPI regmap configuration and
another one for working around an i.Mx hardware bug.
- One omap-usb regression fix.
- One twl6040 build breakage fix.
- One file deletion (ab5500-core.h) that was overlooked during the last
merge window.
* tag 'mfd-for-linus-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Add missing hunk to change palmas irq to clear on read
mfd: Fix palmas regulator pdata missing
mfd: USB: Fix the omap-usb EHCI ULPI PHY reset fix issues.
mfd: Update twl6040 Kconfig to avoid build breakage
mfd: Delete ab5500-core.h
mfd: mc13xxx workaround SPI hardware bug on i.Mx
mfd: Fix mc13xxx SPI regmap
mfd: Add terminating entry for i2c_device_id palmas table
Pull a couple of KVM fixes from Avi Kivity:
"One is an adjustment for an irq layer change that affected device
assignment, the other a one-liner ppc fix."
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
powerpc/kvm: Fix "PR" KVM implementation of H_CEDE
KVM: Fix device assignment threaded irq handler
Commit 080399aaaf ("block: don't mark buffers beyond end of disk as
mapped") exposed a bug in __getblk_slow that causes mount to hang as it
loops infinitely waiting for a buffer that lies beyond the end of the
disk to become uptodate.
The problem was initially reported by Torsten Hilbrich here:
https://lkml.org/lkml/2012/6/18/54
and also reported independently here:
http://www.sysresccd.org/forums/viewtopic.php?f=13&t=4511
and then Richard W.M. Jones and Marcos Mello noted a few separate
bugzillas also associated with the same issue. This patch has been
confirmed to fix:
https://bugzilla.redhat.com/show_bug.cgi?id=835019
The main problem is here, in __getblk_slow:
for (;;) {
struct buffer_head * bh;
int ret;
bh = __find_get_block(bdev, block, size);
if (bh)
return bh;
ret = grow_buffers(bdev, block, size);
if (ret < 0)
return NULL;
if (ret == 0)
free_more_memory();
}
__find_get_block does not find the block, since it will not be marked as
mapped, and so grow_buffers is called to fill in the buffers for the
associated page. I believe the for (;;) loop is there primarily to
retry in the case of memory pressure keeping grow_buffers from
succeeding. However, we also continue to loop for other cases, like the
block lying beond the end of the disk. So, the fix I came up with is to
only loop when grow_buffers fails due to memory allocation issues
(return value of 0).
The attached patch was tested by myself, Torsten, and Rich, and was
found to resolve the problem in call cases.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Reported-and-Tested-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Reviewed-by: Josh Boyer <jwboyer@redhat.com>
Cc: Stable <stable@vger.kernel.org> # 3.0+
[ Jens is on vacation, taking this directly - Linus ]
--
Stable Notes: this patch requires backport to 3.0, 3.2 and 3.3.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Properly define the CAMIF interrupt resources. This device have two
interrupts - corresponding to the "codec" and "preview" data paths.
IRQ_CAM is handled internally by the architecture and demultiplexed
to IRQ_S3C2440_CAM_C and IRQ_S3C2440_CAM_P - these interrupts only
should be handled in the driver.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Use correct gate control bit for AC97 clock which is
S3C2440_CLKCON_AC97, not S3C2440_CLKCON_CAMERA.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The rework of the snd-usb endpoint logic moved the calls to
snd_usb_set_interface() into the snd_usb_endpoint implemenation. This
changed the order in which these calls are issued to the device, and
thereby caused regressions for some webcams.
Fix this by moving the calls back to pcm.c for now to make it work again
and use snd_usb_endpoint_activate() to really tear down all remaining
URBs in the flight, consequently fixing another regression caused by USB
packets on the wire after altsetting 0 has been selected.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Philipp Dreimann <philipp@dreimann.net>
Reported-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I couldn't find the vendor ID in any of the online databases, but this
mat has a Pump It Up logo on the top side of the controller compartment,
and a disclaimer stating that Andamiro will not be liable on the bottom.
Signed-off-by: Yuri Khan <yurivkhan@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Checking for adc->ts_pend already claimed should be done with the
lock held.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The rate of xusbxti clock is set in individual machine files.
The default value should be defined at the clock definition
and individual machine files should modify it if required.
Division by zero in kernel.
[<c0011849>] (unwind_backtrace+0x1/0x9c) from [<c022c663>] (Ldiv0+0x9/0x12)
[<c022c663>] (Ldiv0+0x9/0x12) from [<c001a3c3>] (s3c_setrate_clksrc+0x33/0x78)
[<c001a3c3>] (s3c_setrate_clksrc+0x33/0x78) from [<c0019e67>] (clk_set_rate+0x2f/0x78)
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
We were accidentally losing one bit in the configuration register on
device initialization. It was reported to freeze one specific system
right away. Properly preserve all bits we don't explicitly want to
change in order to prevent that.
Reported-by: Stevie Trujillo <stevie.trujillo@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Commit d640113fe8 introduced a regression on SMP
systems where the processor core with ACPI id zero is disabled
(typically should be the case because of hyperthreading).
The regression got spread through stable kernels.
On 3.0.X it got introduced via 3.0.18.
Such platforms may be rare, but do exist.
Look out for a disabled processor with acpi_id 0 in dmesg:
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x10] disabled)
This problem has been observed on a:
HP Proliant BL280c G6 blade
This patch restricts the introduced workaround to platforms
with nr_cpu_ids <= 1.
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Commit ca1d72f033 ('PM / Domains: Make it possible to add devices to
inactive domains') introduced possibility to add devices to inactive
power domains and added pm_genpd_dev_need_restore() function which lets
platform core to notify power domain core that the specified device must
be restored (with its runtime_resume() callback) before first use.
This patch adds the pm_genpd_dev_need_restore() call what brings back
the suspend/resume behaviour for the client devices known from the
previous power domain driver (removed by commit 91cfbd4ee0 - 'ARM:
EXYNOS: Hook up power domains to generic power domain infrastructure').
Client device drivers relay on that suspend/resume behaviour, thus this
patch fixes runtime pm operation for client devices.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Rob Herring
Arnd Bergmann
Linus Torvalds
Silva Paulo
Will Drewry
Bob Moore
Dave Jones
Jeff Moyer
Sylwester Nawrocki
Daniel Mack
Yuri Khan
Todd Poynor
Tushar Behera
Jean Delvare
Thomas Renninger
Marek Szyprowski