This driver creates a number of const structures that it stores in the
data field of an of_device_id array.
Add const to the declaration of the location that receives a value
from the data field to ensure that the compiler will continue to check
that the value is not modified and remove the const-dropping cast on
the access to the data field.
Done using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
getnstimeofday() suffers from the overflow in y2038 on 32-bit
architectures and requires a conversion into the nanosecond format that
we want here.
This changes ssp_parse_dataframe() to use ktime_get_real_ns() directly,
which does not have that problem.
An open question is what time base should be used here. Normally
timestamps should use ktime_get_ns() or ktime_get_boot_ns() to read
monotonic time instead of "real" time, which suffers from time jumps
due to settimeofday() calls or leap seconds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix gcc warnings about variable 'ec_device' being set but not used
in these files:
common/cros_ec_sensors/cros_ec_sensors.c:194:25
light/cros_ec_light_prox.c:184:25
Signed-off-by: Paolo Cretaro <paolocretaro@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd atomisp
cleanups (take the media tree's version).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnFrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymxbwCgtNlBkqD2JJYpLRKvI/C4w1vzZsEAnA2THRkt
g3ioPBqmqC/2DSbldr2o
=/ebw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd
atomisp cleanups (take the media tree's version)"
* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the user complained that on his system Thinkpad Yoga S1, with
commit f1664eaace ("iio: hid-sensor-trigger: Fix the race with user
space powering up sensors") causes the system to resume immediately
on suspend (S3 operation). On this system the sensor hub is on USB
and is a wake up device from S3. So if any sensor sends data on
motion, the system will wake up. This can be a legitimate use case
to wake up device motion, but that needs proper user space support
to set right thresholds.
In fact the above commit didn't cause this regression, but any operation
which cause sensors to wake up would have caused the same issue. So if
user reads the raw sensor data, same issue occurs, with or without this
commit. Only difference is that the above commit by default will trigger
a power up and power down of sensors as part of runtime pm enable
(runtime enable will cause a runtime resume callback followed by
runtime_suspend callback). Previously user has to do some action on
sensors.
On investigation it was observed that the current driver correctly
changing the state of all sensors to power off but then also some sensor
will still send some data. Only option is to never power up any sensor.
Only good option is to:
- Using sysfs interface disable USB as a wakeup device (This will not
need any driver change)
Since some user don't care about sensors. So for those users this change
brings back old functionality. As long as they don't cause any operation
to power up sensors (like raw read or start iio-sensor-proxy service),
the sensors will not be to touched. This is done by delaying run time
enable till user space does some operation with sensors.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196853
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not try to configure sample frequency if the sensor do not export
odr register address in register map. That change will be used to
properly support LIS3DHH accel sensor.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Define st_sensor_int_drdy structure in st_sensor_data_ready_irq in order
to contain irq line parameters of the device.
Moreover separate data-ready open-drain configuration parameters for INT1
and INT2 pins in st_sensor_data_ready_irq data structure.
That change will be used to properly support LIS3DHH accel sensor.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
New devices (e.g. LIS2DW12) enable all axis by default and do not export
that capability in register map. Check if the enable_axis register
address has been declared in st_sensor_settings map in order to verify if
the driver needs to enable all sensor axis
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Separate data-ready configuration parameters for INT1 and INT2 pins in
st_sensor_data_ready_irq data structure. That change will be use to
properly support LIS2DW12 accel sensor.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce register mask for data-ready status register since
pressure sensors (e.g. LPS22HB) export just two channels
(BIT(0) and BIT(1)) and BIT(2) is marked reserved while in
st_sensors_new_samples_available() value read from status register
is masked using 0x7.
Moreover do not mask status register using active_scan_mask since
now status value is properly masked and if the result is not zero the
interrupt has to be consumed by the driver. This fix an issue on LPS25H
and LPS331AP where channel definition is swapped respect to status
register.
Furthermore that change allows to properly support new devices
(e.g LIS2DW12) that report just ZYXDA (data-ready) field in status register
to figure out if the interrupt has been generated by the device.
Fixes: 97865fe413 (iio: st_sensors: verify interrupt event to status)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
-----BEGIN PGP SIGNATURE-----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=ik5C
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.15a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Round one of new device support, features and cleanup for IIO in the 4.15 cycle.
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
Note this includes fixes from recent merge window. As such the tree
is based on top of a prior staging/staging-next tree.
* iio core
- return and error for a failed read_reg debugfs call rather than
eating the error.
* ad7192
- Use the dedicated reset function in the ad_sigma_delta library
instead of an spi transfer with the data on the stack which
could cause problems with DMA.
* ad7793
- Implement a dedicate reset function in the ad_sigma_delta library
and use it to correctly reset this part.
* bme280
- ctrl_reg write must occur after any register writes
for updates to take effect.
* mcp320x
- negative voltage readout was broken.
- Fix an oops on module unload due to spi_set_drvdata not being called
in probe.
* st_magn
- Fix the data ready line configuration for the lis3mdl. It is not
configurable so the st_magn core was assuming it didn't exist
and so wasn't consuming interrupts resulting in an unhandled
interrupt.
* stm32-adc
- off by one error on max channels checking.
* stm32-timer
- preset should not be buffered - reorganising register writes avoids
this.
- fix a corner case in which write preset goes wrong when a timer is
used first as a trigger then as a counter with preset. Odd case but
you never know.
* ti-ads1015
- Fix setting of comparator polarity by fixing bitfield definition.
* twl4030
- Error path handling fix to cleanup in event of regulator
registration failure.
- Disable the vusb3v1 regulator correctly in error handling
- Don't paper over a regulator enable failure.
-----BEGIN PGP SIGNATURE-----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=CcjQ
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of IIO fixes for the 4.14 cycle
Note this includes fixes from recent merge window. As such the tree
is based on top of a prior staging/staging-next tree.
* iio core
- return and error for a failed read_reg debugfs call rather than
eating the error.
* ad7192
- Use the dedicated reset function in the ad_sigma_delta library
instead of an spi transfer with the data on the stack which
could cause problems with DMA.
* ad7793
- Implement a dedicate reset function in the ad_sigma_delta library
and use it to correctly reset this part.
* bme280
- ctrl_reg write must occur after any register writes
for updates to take effect.
* mcp320x
- negative voltage readout was broken.
- Fix an oops on module unload due to spi_set_drvdata not being called
in probe.
* st_magn
- Fix the data ready line configuration for the lis3mdl. It is not
configurable so the st_magn core was assuming it didn't exist
and so wasn't consuming interrupts resulting in an unhandled
interrupt.
* stm32-adc
- off by one error on max channels checking.
* stm32-timer
- preset should not be buffered - reorganising register writes avoids
this.
- fix a corner case in which write preset goes wrong when a timer is
used first as a trigger then as a counter with preset. Odd case but
you never know.
* ti-ads1015
- Fix setting of comparator polarity by fixing bitfield definition.
* twl4030
- Error path handling fix to cleanup in event of regulator
registration failure.
- Disable the vusb3v1 regulator correctly in error handling
- Don't paper over a regulator enable failure.
Pull HID update from Jiri Kosina:
- Wacom driver fixes/updates (device name generation improvements,
touch ring status support) from Jason Gerecke
- T100 touchpad support from Hans de Goede
- support for batteries driven by HID input reports, from Dmitry
Torokhov
- Arnd pointed out that driver_lock semaphore is superfluous, as driver
core already provides all the necessary concurency protection.
Removal patch from Binoy Jayan
- logical minimum numbering improvements in sensor-hub driver, from
Srinivas Pandruvada
- support for Microsoft Win8 Wireless Radio Controls extensions from
João Paulo Rechi Vita
- assorted small fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (28 commits)
HID: prodikeys: constify snd_rawmidi_ops structures
HID: sensor: constify platform_device_id
HID: input: throttle battery uevents
HID: usbmouse: constify usb_device_id and fix space before '[' error
HID: usbkbd: constify usb_device_id and fix space before '[' error.
HID: hid-sensor-hub: Force logical minimum to 1 for power and report state
HID: wacom: Do not completely map WACOM_HID_WD_TOUCHRINGSTATUS usage
HID: asus: Add T100CHI bluetooth keyboard dock touchpad support
HID: ntrig: constify attribute_group structures.
HID: logitech-hidpp: constify attribute_group structures.
HID: sensor: constify attribute_group structures.
HID: multitouch: constify attribute_group structures.
HID: multitouch: use proper symbolic constant for 0xff310076 application
HID: multitouch: Support Asus T304UA media keys
HID: multitouch: Support HID_GD_WIRELESS_RADIO_CTLS
HID: input: optionally use device id in battery name
HID: input: map digitizer battery usage
HID: Remove the semaphore driver_lock
HID: wacom: add USB_HID dependency
HID: add ALWAYS_POLL quirk for Logitech 0xc077
...
Data-ready line in LIS3MDL is routed to drdy pin and it is not possible
to select a different INT pin. st_sensors_set_dataready_irq() assumes
that if drdy int address is not exported in register map, irq trigger
is not supported by the sensor and hw_irq_trigger is always false.
Based on this configuration st_sensors_irq_thread does not consume
generated interrupt causing an unhandled irq.
Fix this taking into account status register address in
st_sensors_set_dataready_irq()
Fixes: 90efe05562 (iio: st_sensors: harden interrupt handling)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Clearly this set jumps across multiple areas, but inherently it
can't be grouped like the other sets in this series so I've done
all the stuff in the common directory together.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
It has been reported for a while that with iio-sensor-proxy service the
rotation only works after one suspend/resume cycle. This required a wait
in the systemd unit file to avoid race. I found a Yoga 900 where I could
reproduce this.
The problem scenerio is:
- During sensor driver init, enable run time PM and also set a
auto-suspend for 3 seconds.
This result in one runtime resume. But there is a check to avoid
a powerup in this sequence, but rpm is active
- User space iio-sensor-proxy tries to power up the sensor. Since rpm is
active it will simply return. But sensors were not actually
powered up in the prior sequence, so actaully the sensors will not work
- After 3 seconds the auto suspend kicks
If we add a wait in systemd service file to fire iio-sensor-proxy after
3 seconds, then now everything will work as the runtime resume will
actually powerup the sensor as this is a user request.
To avoid this:
- Remove the check to match user requested state, this will cause a
brief powerup, but if the iio-sensor-proxy starts immediately it will
still work as the sensors are ON.
- Also move the autosuspend delay to place when user requested turn off
of sensors, like after user finished raw read or buffer disable
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In the reference HID sensor hub firmware all Named array enums were
0-based. There is no description of the default base of enums in HID
sensor hub specification as logical minimum should have set this base
value.
Every sensor hub implemented enum as 1-based, without explicitly setting
logical minimum to 1, because of the implementation by one of the major
OS vendor. In Linux we used logical minimum to decide the enum base.
Some sensor hub FWs already changed logical minimum from 0 to 1. We hoped
that every other vendor will follow. But that didn't happen and we had to
fix the report header for every sensor hub to change logical minimum to 1
by using .report_fixup() callback. So for every new sensor hub we had to
modify source code by adding this quirk based on the vendor and device id.
This is becoming a maintenance burden.
This patch hardcodes the logical minimum of power and report state
attributes to 1. In this way we can remove the existing quirks and also
we don't have to add more quirks.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* ad2s1210
- Fix negative angular velocity reads (identified by a gcc 7 warning)
* aspeed-adc
- Wait for initialization sequence to finish before enabling channels.
Without it no channels work.
* axp288
- Revert a patch that dropped some bogus register mods. No one is entirely
sure why but it breaks charging on some devices.
- Fix GPADC pin read returning 0. Turns out a small sleep is needed.
* bmc150
- Make sure device is restored to normal state after suspend / resume
cycle. Otherwise, simple sysfs reads are broken.
* tsl2563
- fix wrong event code.
* st-accel
- add spi 3-wire support. Needed to fix the lsm303agr accelerometer
which only had 3 wires in all cases. Side effect is to enable optional
3-wire support for other devices.
* st-pressure
- disable multiread by default for LPS22HB (only effects SPI)
* sun4i-gpadc-iio
- fix unbalanced irq enable / disable
* vf610
- Fix VALT slection for REFSEL bits - ensures we are using the
right reference pins.
-----BEGIN PGP SIGNATURE-----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=BApO
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.13 cycle.
* ad2s1210
- Fix negative angular velocity reads (identified by a gcc 7 warning)
* aspeed-adc
- Wait for initialization sequence to finish before enabling channels.
Without it no channels work.
* axp288
- Revert a patch that dropped some bogus register mods. No one is entirely
sure why but it breaks charging on some devices.
- Fix GPADC pin read returning 0. Turns out a small sleep is needed.
* bmc150
- Make sure device is restored to normal state after suspend / resume
cycle. Otherwise, simple sysfs reads are broken.
* tsl2563
- fix wrong event code.
* st-accel
- add spi 3-wire support. Needed to fix the lsm303agr accelerometer
which only had 3 wires in all cases. Side effect is to enable optional
3-wire support for other devices.
* st-pressure
- disable multiread by default for LPS22HB (only effects SPI)
* sun4i-gpadc-iio
- fix unbalanced irq enable / disable
* vf610
- Fix VALT slection for REFSEL bits - ensures we are using the
right reference pins.
Add SPI Serial Interface Mode (SIM) register information
in st_sensor_settings look up table to support devices
(like LSM303AGR accel sensor) that allow just SPI-3wire
communication mode. SIM mode has to be configured before any
other operation since it is not enabled by default and the driver
is not able to read without that configuration
Whilst a fairly substantial patch, the actual logic is simple and it
is better to have the generic fix than a band aid.
Fixes: ddc05fa286 (iio: st-accel: add support for lsm303agr accel)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move st_sensors_of_i2c_probe() in st_sensors_core and rename it in
st_sensors_of_name_probe(). That change is necessary to add device-tree
support in spi code otherwise the rest of the autodetection will fail
since spi->modalias (and indio_dev->name) will be set using compatible
string value that differs from standard sensor name
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Building a kernel with my configuration failed with:
> drivers/built-in.o: In function `hid_sensor_setup_batch_mode': staging/drivers/iio/common/hid-sensors/hid-sensor-trigger.c:104: undefined reference to `iio_buffer_set_attrs'
which is fixed by this patch.
Signed-off-by: Alexander Wuerstlein <arw@arw.name>
Fixes: 138bc7969c ("iio: hid-sensor-hub: Implement batch mode")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
HID sensor hubs using Integrated Senor Hub (ISH) has added capability to
support batch mode. This allows host processor to go to sleep for extended
duration, while the sensor hub is storing samples in its internal buffers.
'Commit f4f4673b75 ("iio: add support for hardware fifo")' implements
feature in IIO core to implement such feature. This feature is used in
bmc150-accel-core.c to implement batch mode. This implementation allows
software device buffer watermark to be used as a hint to adjust hardware
FIFO.
But HID sensor hubs don't allow to change internal buffer size of FIFOs.
Instead an additional usage id to set "maximum report latency" is defined.
This allows host to go to sleep upto this latency period without getting
any report. Since there is no ABI to set this latency, a new attribute
"hwfifo_timeout" is added so that user mode can specify a latency.
This change checks presence of usage id to get/set maximum report latency
and if present, it will expose hwfifo_timeout.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add orientation sensor "scale" and "offset" parse support.
These two properties are needed for exponent data conversion.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Xu Even <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Ensure that when an invalid value in ret or value is found -EINVAL
is returned. A previous commit broke the way the return error is
being returned and instead caused the return code in ret to be
re-assigned rather than be returned.
Fixes: 5d9854eaea ("iio: hid-sensor: Store restore poll and hysteresis on S3")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
As these are rather late in the cycle, they may sneak over into 4.12.
There is a fix for a regression caused by another fix (hid sensors
hardware seems to vary a lot in how various corner cases are handled).
* ad7303
- fix channel description. Numeric values were being passed as characters
presumably leading to garbage from the userspace interface.
* as3935
- the write data macro was wrong so fix it.
* bmp280
- incorrect handling of negative values as being unsigned broke humidity
calculation.
* hid-sensor
- Restore the poll and hysteresis values after resume as some hardware
doesn't do it.
* stm32-trigger
- buglet in reading the sampling frequency
-----BEGIN PGP SIGNATURE-----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=H5KS
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.11e' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Fifth set of IIO fixes for the 4.11 cycle.
As these are rather late in the cycle, they may sneak over into 4.12.
There is a fix for a regression caused by another fix (hid sensors
hardware seems to vary a lot in how various corner cases are handled).
* ad7303
- fix channel description. Numeric values were being passed as characters
presumably leading to garbage from the userspace interface.
* as3935
- the write data macro was wrong so fix it.
* bmp280
- incorrect handling of negative values as being unsigned broke humidity
calculation.
* hid-sensor
- Restore the poll and hysteresis values after resume as some hardware
doesn't do it.
* stm32-trigger
- buglet in reading the sampling frequency
New device support
* max1117, 1118 and 1119
- new ADC driver
* max9611
- new ADC driver
* pm8xxx hk/xoadc
- new driver with some shared features broken out from the SPMI vadc.
* sun4i-gpadc
- A33 thermal sensor support (with associated rework)
* stm32-dac
- new driver and bindings
* stm32 trigger
- enable support of quadrature encoder device and counter modes
Features
* apds9960
- use the runtime pm for normal suspend
* stm32-adc
- add opition to sest resolution via devicetree
* xoadc
- augment DT bindings to deal with some weird mux cases
Cleanups
* ad5933
- protect direct mode using claim and release helpers
* ade7759
- S_IRUGO and friends to octal in two goes
* adis16203
- drop unnecessary brackets
* hid-sensor
- fix unbalanced pm_runtieme_enable error when probing after remove
* lsm6dsx
- use actual part numbers for device name when known
- simplify data read pin parsing
* mpu3050
- avoid double reporting errors
-----BEGIN PGP SIGNATURE-----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=zHqs
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.12d' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Fourth set of IIO new device support, features and cleanups for the 4.12 cycle
New device support
* max1117, 1118 and 1119
- new ADC driver
* max9611
- new ADC driver
* pm8xxx hk/xoadc
- new driver with some shared features broken out from the SPMI vadc.
* sun4i-gpadc
- A33 thermal sensor support (with associated rework)
* stm32-dac
- new driver and bindings
* stm32 trigger
- enable support of quadrature encoder device and counter modes
Features
* apds9960
- use the runtime pm for normal suspend
* stm32-adc
- add opition to sest resolution via devicetree
* xoadc
- augment DT bindings to deal with some weird mux cases
Cleanups
* ad5933
- protect direct mode using claim and release helpers
* ade7759
- S_IRUGO and friends to octal in two goes
* adis16203
- drop unnecessary brackets
* hid-sensor
- fix unbalanced pm_runtieme_enable error when probing after remove
* lsm6dsx
- use actual part numbers for device name when known
- simplify data read pin parsing
* mpu3050
- avoid double reporting errors
When a hid sensor module is removed and modprobed again we see
error for unbalanced pm_runtime. This issue is caused by not
deactivating runtime PM on removal. So on modprobe again when
activated again, this will print this error.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This change undo the change done by 'commit 3bec247474
("iio: hid-sensor-trigger: Change get poll value function order to avoid
sensor properties losing after resume from S3")' as this breaks some
USB/i2c sensor hubs.
Instead of relying on HW for restoring poll and hysteresis, driver stores
and restores on resume (S3). In this way user space modified settings are
not lost for any kind of sensor hub behavior.
In this change, whenever user space modifies sampling frequency or
hysteresis driver will get the feature value from the hub and store in the
per device hid_sensor_common data structure. On resume callback from S3,
system will set the feature to sensor hub, if user space ever modified the
feature value.
Fixes: 3bec247474 ("iio: hid-sensor-trigger: Change get poll value function order to avoid sensor properties losing after resume from S3")
Reported-by: Ritesh Raj Sarraf <rrs@researchut.com>
Tested-by: Ritesh Raj Sarraf <rrs@researchut.com>
Tested-by: Song, Hongyan <hongyan.song@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Somewhat dominated in patch numbers of last of the outreachy application
window related patches (they are still coming, despite window being closed
which is good to see!)
Good set of new drivers as well.
New device support
* ASPEED ADC
- new driver
* cpcap PMIC ADC
- new driver
* hid-humidity
- driver for HID compatible humidity sensors.
* ltc2497 ADC
- new driver
* mpu6050
- bring bindings up to date and add trivial support for 9250
* rockchip-saradc
- update bindings to cover rk3328
* vl6180 light, proximity and time of flight sensor.
- new driver
Features
* meson-saradc
- add calibration
Cleanup and minor fixes
* ad5504
- constify attribute_group structure
- drop casting of void *
* ad7150
- replace some shifts of 1 by BIT macro usage
* ad7152
- blank lines between function definitions
* ad7280a
- octal permissions.
* ad7606
- replace use of core mlock mutex with a local lock
* ad7746
- replace some shifts of 1 by BIT macro usage
- function parameter alignment
- drop some excessive brackets (introduced in last pull request)
* ad7753
- white space cleanup
* ad7754
- includes in alphabetical order and groupped appropriately.
- change from missuse of internal mlock mutex to using the buffer lock to
also protect values during frequency update.
* ad779x
- constify attribute_group structures
* ad9832
- octal permissions
* adis16060
- remove use of core mlock mutex in favour of adding a local
_spi_write_then_read which can use the local buffer protection lock.
- fix naming of above function.
* adis16203
- remove locking during reads of calibbias that doesn't protect anything
not protected elsewhere.
* adis16209
- remove unnecessary braces in single statement if
* adis16240
- remove unnecessary braces in single statement if
* adt7136
- drop excess blank lines and put some in between functions.
* ams-iaq
- replace comma with semi colon. Not actual bug, just unusual syntax.
* apds9960
- constify attribute group structure
* as3935
- constify attribute group structure
* bm1750
- constify attribute group structure
* cros_ec
- devm version of triggered buffer setup to simplify code.
* exynos
- drop casting of void *
* hdc100x
- constify attribute_group structure
* hid-accel
- fix wrong scale for newly introduced gravity sensor.
* hts221
- drop casting of void *
* hx711
- constify attribute_group structure
* imx7d_adc
- drop casting of void *
* lm35333
- constify attribute_group structure
* lsm6dsx
- drop casting of void *
- hold ODR configuration until enabling to avoid a race condition.
* max1027
- drop casting of void *
* max11100
- fix a comma where semicolon was intended (no actual bug, just odd)
* max1363
- constify attribute_group structure
* ms sensors
- drop casting of void *
* rockchip_saradc
- drop casting of void *
* sun4i-gpadc
- fix missing dependency on THERMAL or presence of stubs (issue only
introduced in pervious set)
- drop casting of void *
* tsl2x7x
- fix wrong standard deviation calc. Note these aren't actually used for
anything at the moment so bug didn't really matter.
- constify attribute group structure.
* vf610adc
- drop casting of void *
* vz89x
- replace comma with semicolon. Not actual bug, just odd syntax.
* zpa2326
- drop casting of void *
-----BEGIN PGP SIGNATURE-----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=YYdq
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.12c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Third set of new device support, cleanups and features for IIO in the 4.12 cycle
Somewhat dominated in patch numbers of last of the outreachy application
window related patches (they are still coming, despite window being closed
which is good to see!)
Good set of new drivers as well.
New device support
* ASPEED ADC
- new driver
* cpcap PMIC ADC
- new driver
* hid-humidity
- driver for HID compatible humidity sensors.
* ltc2497 ADC
- new driver
* mpu6050
- bring bindings up to date and add trivial support for 9250
* rockchip-saradc
- update bindings to cover rk3328
* vl6180 light, proximity and time of flight sensor.
- new driver
Features
* meson-saradc
- add calibration
Cleanup and minor fixes
* ad5504
- constify attribute_group structure
- drop casting of void *
* ad7150
- replace some shifts of 1 by BIT macro usage
* ad7152
- blank lines between function definitions
* ad7280a
- octal permissions.
* ad7606
- replace use of core mlock mutex with a local lock
* ad7746
- replace some shifts of 1 by BIT macro usage
- function parameter alignment
- drop some excessive brackets (introduced in last pull request)
* ad7753
- white space cleanup
* ad7754
- includes in alphabetical order and groupped appropriately.
- change from missuse of internal mlock mutex to using the buffer lock to
also protect values during frequency update.
* ad779x
- constify attribute_group structures
* ad9832
- octal permissions
* adis16060
- remove use of core mlock mutex in favour of adding a local
_spi_write_then_read which can use the local buffer protection lock.
- fix naming of above function.
* adis16203
- remove locking during reads of calibbias that doesn't protect anything
not protected elsewhere.
* adis16209
- remove unnecessary braces in single statement if
* adis16240
- remove unnecessary braces in single statement if
* adt7136
- drop excess blank lines and put some in between functions.
* ams-iaq
- replace comma with semi colon. Not actual bug, just unusual syntax.
* apds9960
- constify attribute group structure
* as3935
- constify attribute group structure
* bm1750
- constify attribute group structure
* cros_ec
- devm version of triggered buffer setup to simplify code.
* exynos
- drop casting of void *
* hdc100x
- constify attribute_group structure
* hid-accel
- fix wrong scale for newly introduced gravity sensor.
* hts221
- drop casting of void *
* hx711
- constify attribute_group structure
* imx7d_adc
- drop casting of void *
* lm35333
- constify attribute_group structure
* lsm6dsx
- drop casting of void *
- hold ODR configuration until enabling to avoid a race condition.
* max1027
- drop casting of void *
* max11100
- fix a comma where semicolon was intended (no actual bug, just odd)
* max1363
- constify attribute_group structure
* ms sensors
- drop casting of void *
* rockchip_saradc
- drop casting of void *
* sun4i-gpadc
- fix missing dependency on THERMAL or presence of stubs (issue only
introduced in pervious set)
- drop casting of void *
* tsl2x7x
- fix wrong standard deviation calc. Note these aren't actually used for
anything at the moment so bug didn't really matter.
- constify attribute group structure.
* vf610adc
- drop casting of void *
* vz89x
- replace comma with semicolon. Not actual bug, just odd syntax.
* zpa2326
- drop casting of void *
When system bootup without get sensor property, set sensor
property will be fail.
If no get_feature operation done before set_feature, the sensor
properties will all be the initialized value, which is not the
same with sensor real properties. When set sensor property it will
write back to sensor the changed perperty data combines with other
sensor properties data, it is not right and may be dangerous.
In order to get all sensor properties, choose to read one of the sensor
properties(no matter read any sensor peroperty, driver will get all
the peroperties and return the requested one).
Fixes: 73c6768b71 ("iio: hid-sensors: Common attribute and trigger")
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following Coccinelle script was used to detect this:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T*)x)->f
|
- (T*)
e
)
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Environmental humidity sensor is a hid defined sensor,
it shows raw humidity measurement of air.
More information can be found in:
http://www.usb.org/developers/hidpage/HUTRR39b.pdf
According to IIO ABI definition, humidityrelative data output unit is
milli percent. Add the unit convert from percent to milli percent.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Scale value include two parts: unit conversion and exponent conversion.
Add gravity unit convert table to fix gravity sensor scale value not
right issue.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use resourced managed function devm_iio_triggered_buffer_setup
to make error path simpler and be able to get rid of the remove
function.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The cros_ec_sensors_read function must return the type of value on all
cases. This was always true except for RAW and CALIBBIAS data which
returned an error or 0. This patch just fixes the mistake I introduced
when submitting the series.
Fixes: commit c14dca07a3 (iio: cros_ec_sensors: add ChromeOS EC
Contiguous Sensors driver)
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In function _hid_sensor_power_state(), when hid_sensor_read_poll_value()
is called, sensor's all properties will be updated by the value from
sensor hardware/firmware.
In some implementation, sensor hardware/firmware will do a power cycle
during S3. In this case, after resume, once hid_sensor_read_poll_value()
is called, sensor's all properties which are kept by driver during S3
will be changed to default value.
But instead, if a set feature function is called first, sensor
hardware/firmware will be recovered to the last status. So change the
sensor_hub_set_feature() calling order to behind of set feature function
to avoid sensor properties lose.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Environmental temperature sensor is a hid defined sensor,
it measures temperature.
More information can be found in:
http://www.usb.org/developers/hidpage/HUTRR39b.pdf
According to IIO ABI definition, IIO_TEMP data output unit is
milli degrees Celsius. Add the unit convert from degree to milli degree.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
It's shaping to be another fairly busy cycle. Lots more on the way!
New device support
* ads7950
- new driver supporting ads7950, ads7951, ads7952, ads7953, ads7954,
ads7955, ads7956, ads7957, ads7958, ads7959, ads7960, and ads7961 ADCs.
* cm3605
- New driver for this light sensor and proximity sensor which is an
analog part with some additional digital controls.
* hx711
- New driver.
Core new stuff
* Gravity sensor type. This is a processed datastream in which the device
will try to work out which way is down.
* Split the buffer.h file into two parts. One provides the interface to 'use'
a buffer, the second provides the internals of the buffer functionality as
needed by implementations of buffers.
- Move documentation inline so as to allow use of private: tag when
generating documentation.
- Add some utility functions for the few things that are directly done
with the buffers.
- Stop exporting functions that no-one uses outside of the core code.
- Push docs down by the code in the c file where they should have always
been.
- Fix typo in kernel-doc for buffer.
- push down some includes that were previously happening implicitly.
- stop enabling the timestamp of the dummy device.
Features and cleanups
* ad5592r
- ACPI support
* ad5593r
-ACPI support.
* ad5933
- Fix a false comment about size of a particular register.
* ad7150
- replace S_IRUGO | S_IWUSR with 0644. I'm not that keen on these patches
in general, but as it was nicely presented I took this one anyway. As a
general rule will only take these as part of a larger driver cleanup.
- don't eat an error but rather reutnr it in the write_event_config callback.
* ad7606
- replace non standard range attibute with _scale
* ade7753
- use usleep_range for short sleeps
* ade7754
- use usleep_range for short sleeps
* ade7758
- use usleep_range for short sleeps
* ade7759
- use usleep_range for short sleeps
* ade7854
- use usleep_range for short sleeps
* adis16201
- fix description
* adis16203
- fix description
- fix copyright year
* adis16209
- fix description
* adt7316
- Add braces to arms of if else statement (for consistency)
- Alignment fixes.
* axp288
- Fix up an issue with accidental overwrites of data.
* bmi160
- add deivce tables for i2c and spi to support correctly identifying the
full dt name (including manufacturer).
- device tree binding.
* bmp280
- use usleep_range for short sleeps.
* cm3232
- return error from cm3232_reg_init rather than eating it if the last write
fails.
* dummy driver
- remove a semicolor found at end of a function defintition.
* exynos-adc
- use usleep_range for short sleeps.
* hid-sensor (accel)
- Add timestamp support. The hardware can provide timestamps so lets support
them. If not fall back to timestamps estimated in kernel.
* hid-sensor (light)
- Add a duplicate ID for the light channels so as to keep existing interface
whilst also using the more standard IIO interface.
* hts221
- acpi probing
* imx25-gcq
- Add a macro call to allow this driver to be automatically loaded.
* isl29028
- reorganise code to avoid deep nesting of if statements.
- move chip test and default regs into a function suitable or sharing with
power management code.
- tidy up some code alignment.
* lidar-lite-v3
- introduce compatible strings that make it clear Garmin have consideral
friends.
* mma8452
- avoid returning signed value when unsigned is appropriate
* spmi-vadc
- Update function for generic voltage conversion to take into account that
different channels on this device should be handled differently.
- Rework code to allow per channel voltage scaling and support the standard
options for this hardware.
- Fixup three minor issues with the above patches for this part. These all
effect test builds rather than the native builds for the part, but good to
clean them up anyway.
* st_sensors
- support device matching from the ACPI DST tables.
- acpi based probing for accelerometers
- acpi based probing for pressure sensors
- Allow pressure sensors to read negative values.
- Export sampling frequency for lps25h and lps331ap.
- Add support for the old DT bindings from the period when these deivces
were often supported through windows.
Docs fixup:
* typo in sysfs-bus-iio
-----BEGIN PGP SIGNATURE-----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=yjUA
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.11a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new device support, features and cleanups for IIO in the 4.11 cycle.
It's shaping to be another fairly busy cycle. Lots more on the way!
New device support
* ads7950
- new driver supporting ads7950, ads7951, ads7952, ads7953, ads7954,
ads7955, ads7956, ads7957, ads7958, ads7959, ads7960, and ads7961 ADCs.
* cm3605
- New driver for this light sensor and proximity sensor which is an
analog part with some additional digital controls.
* hx711
- New driver.
Core new stuff
* Gravity sensor type. This is a processed datastream in which the device
will try to work out which way is down.
* Split the buffer.h file into two parts. One provides the interface to 'use'
a buffer, the second provides the internals of the buffer functionality as
needed by implementations of buffers.
- Move documentation inline so as to allow use of private: tag when
generating documentation.
- Add some utility functions for the few things that are directly done
with the buffers.
- Stop exporting functions that no-one uses outside of the core code.
- Push docs down by the code in the c file where they should have always
been.
- Fix typo in kernel-doc for buffer.
- push down some includes that were previously happening implicitly.
- stop enabling the timestamp of the dummy device.
Features and cleanups
* ad5592r
- ACPI support
* ad5593r
-ACPI support.
* ad5933
- Fix a false comment about size of a particular register.
* ad7150
- replace S_IRUGO | S_IWUSR with 0644. I'm not that keen on these patches
in general, but as it was nicely presented I took this one anyway. As a
general rule will only take these as part of a larger driver cleanup.
- don't eat an error but rather reutnr it in the write_event_config callback.
* ad7606
- replace non standard range attibute with _scale
* ade7753
- use usleep_range for short sleeps
* ade7754
- use usleep_range for short sleeps
* ade7758
- use usleep_range for short sleeps
* ade7759
- use usleep_range for short sleeps
* ade7854
- use usleep_range for short sleeps
* adis16201
- fix description
* adis16203
- fix description
- fix copyright year
* adis16209
- fix description
* adt7316
- Add braces to arms of if else statement (for consistency)
- Alignment fixes.
* axp288
- Fix up an issue with accidental overwrites of data.
* bmi160
- add deivce tables for i2c and spi to support correctly identifying the
full dt name (including manufacturer).
- device tree binding.
* bmp280
- use usleep_range for short sleeps.
* cm3232
- return error from cm3232_reg_init rather than eating it if the last write
fails.
* dummy driver
- remove a semicolor found at end of a function defintition.
* exynos-adc
- use usleep_range for short sleeps.
* hid-sensor (accel)
- Add timestamp support. The hardware can provide timestamps so lets support
them. If not fall back to timestamps estimated in kernel.
* hid-sensor (light)
- Add a duplicate ID for the light channels so as to keep existing interface
whilst also using the more standard IIO interface.
* hts221
- acpi probing
* imx25-gcq
- Add a macro call to allow this driver to be automatically loaded.
* isl29028
- reorganise code to avoid deep nesting of if statements.
- move chip test and default regs into a function suitable or sharing with
power management code.
- tidy up some code alignment.
* lidar-lite-v3
- introduce compatible strings that make it clear Garmin have consideral
friends.
* mma8452
- avoid returning signed value when unsigned is appropriate
* spmi-vadc
- Update function for generic voltage conversion to take into account that
different channels on this device should be handled differently.
- Rework code to allow per channel voltage scaling and support the standard
options for this hardware.
- Fixup three minor issues with the above patches for this part. These all
effect test builds rather than the native builds for the part, but good to
clean them up anyway.
* st_sensors
- support device matching from the ACPI DST tables.
- acpi based probing for accelerometers
- acpi based probing for pressure sensors
- Allow pressure sensors to read negative values.
- Export sampling frequency for lps25h and lps331ap.
- Add support for the old DT bindings from the period when these deivces
were often supported through windows.
Docs fixup:
* typo in sysfs-bus-iio
As a precursor to splitting buffer.h, lets make sure all drivers
include the relevant headers rather than relying on picking them
up from kfifo_buf.h.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The LIS3LV02 has a special bit that need to be set to get the
read values left aligned. Before this patch we get gibberish
like this:
iio_generic_buffer -a -c10 -n lis3lv02dl_accel
(...)
0.000000 -0.010042 -0.642688 19155832931907
0.000000 -0.010042 -0.642688 19155858751073
Which is because we read a raw value for 1g as 64 which is
the nominal 1024 for 1g shifted 4 bits to the left by being
right-aligned rather than left aligned.
Since all other sensors are left aligned, add some code to
set the special DAS (data alignment setting) bit to 1 so that
the right value is now read like this:
iio_generic_buffer -a -c10 -n lis3lv02dl_accel
(...)
0.000000 -0.147095 -10.120135 24761614364956
-0.029419 -0.176514 -10.120135 24761631624540
The scaling was weird as well: we have a gain of 1000 for 1g
and 3000 for 6g. I don't even remember how I came up with the
old values but they are wrong.
Fixes: 3acddf74f8 ("iio: st-sensors: add support for lis3lv02d accelerometer")
Cc: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Using realbits as i2c/spi read len, when that value is not byte aligned
(e.g 12 bits), lead to skip msb part of out data registers.
Fix this taking into account scan_type.shift in addition to
scan_type.realbits as read length:
read_len = DIV_ROUND_UP(realbits + shift, 8)
This fix has been tested on 8, 12, 16, 24 bit sensors
Fixes: e7385de529 ("iio:st_sensors: align on storagebits boundaries")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added timestamp channel. With this change, each sample has a timestamp.
This timestamp can be from the sensor hub when present or local kernel
timestamp. HID sensors can send timestamp with input data using usage id
HID_USAGE_SENSOR_TIME_TIMESTAMP. This timestamp value is converted to
nano seconds before pushing this sample to the iio core.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support to match st sensors using information passed from ACPI DST
tables.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Julia Lawall
Arnd Bergmann
Paolo Cretaro
Kees Cook
Linus Torvalds
Greg Kroah-Hartman
Srinivas Pandruvada
Lorenzo Bianconi
Jonathan Cameron
Alexander Wuerstlein
Song Hongyan
Colin Ian King
simran singhal
Enric Balletbo i Serra
Linus Walleij
Shrirang Bagul