Commit a0f97e06a4 ("kbuild: enable 'make CFLAGS=...' to add
additional options to CC") renamed CFLAGS to KBUILD_CFLAGS.
Commit 222d394d30 ("kbuild: enable 'make AFLAGS=...' to add
additional options to AS") renamed AFLAGS to KBUILD_AFLAGS.
Commit 06c5040cdb ("kbuild: enable 'make CPPFLAGS=...' to add
additional options to CPP") renamed CPPFLAGS to KBUILD_CPPFLAGS.
For some reason, LDFLAGS was not renamed.
Using a well-known variable like LDFLAGS may result in accidental
override of the variable.
Kbuild generally uses KBUILD_ prefixed variables for the internally
appended options, so here is one more conversion to sanitize the
naming convention.
I did not touch Makefiles under tools/ since the tools build system
is a different world.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
The binding for the USB PHY went thru before the driver. However the
new version of the driver now use the PHY core support for reset, and
this expect the reset to be named "phy". So remove the "usb-" prefix
from the the reset names.
Signed-off-by: Alban Bedel <albeu@free.fr>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/15282/
Cc: linux-kernel@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Ocelot now has a u-boot port, allow building FIT images instead of relying
on the legacy detection and builtin DTB.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19632/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Make use of the spi-gpio driver to provide SPI support on the Ingenic
JZ4780 SoC using the pins that can be used with the SSI0 device as
GPIOs, until such time as we have support for the Ingenic SPI/SSI
controller.
[paul.burton@mips.com: Rewrite commit message.]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19489/
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
prom_putchar() is used centrally in early printk infrastructure therefore
at least MIPS should agree on the function return type.
[paul.burton@mips.com:
- Include linux/types.h in asm/setup.h to gain the bool typedef before
we start include asm/setup.h elsewhere.
- Include asm/setup.h in all files that use or define prom_putchar().
- Also standardise on signed rather than unsigned char argument.]
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19842/
Cc: linux-mips@linux-mips.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Merge the build rule of vmlinux.{gz,bz2,lzma,lzo}.itb, and also move
'targets' close to the related code.
[paul.burton@mips.com:
- Remove leading tabs from assignments to itb_addr_cells, since after
this patch moves the additions to the 'targets' variable the
assignments to itb_addr_cells wound up being treated as part of the
uImage rule above them, causing the .its to incorrectly be generated
with empty ADDR_CELLS.]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Patchwork: https://patchwork.linux-mips.org/patch/19095/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-kernel@vger.kernel.org
The build rule of vmlinux.*.its is invoked by $(call if_changed,...)
but it always rebuilds the target needlessly due to missing targets.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Patchwork: https://patchwork.linux-mips.org/patch/19092/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-kernel@vger.kernel.org
As Documentation/kbuild/makefile.txt says, it is a typical mistake
to forget the FORCE prerequisite for the rule invoked by if_changed.
Add the FORCE to the prerequisite, but it must be filtered-out from
the files passed to the 'cat' command. Because this rule generates
.vmlinux.its.S.cmd, vmlinux.its.S must be specified as targets so
that the .cmd file is included.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Patchwork: https://patchwork.linux-mips.org/patch/19097/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-kernel@vger.kernel.org
$(CPP) is used here to perform macro replacement in ITS. Do not
pass $(cpp_flags) because it pulls in more options for dependency
file generation etc. but none of which is necessary here. ITS files
do not include any header file, so $(call if_change,...) is enough.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Patchwork: https://patchwork.linux-mips.org/patch/19093/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-kernel@vger.kernel.org
This reverts commit 0f9da844d8.
It is true that commit 0f9da844d8 ("MIPS: boot: Define __ASSEMBLY__
for its.S build") fixed the build error, but it should not have
defined __ASSEMBLY__ just for textual substitution in arbitrary data.
The file is image tree source in this case, but the purpose of using
CPP is to replace some macros.
I merged a better solution, commit a95b37e20d ("kbuild: get
<linux/compiler_types.h> out of <linux/kconfig.h>"). The original
fix-up is no longer needed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Patchwork: https://patchwork.linux-mips.org/patch/19096/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-kernel@vger.kernel.org
Use fixed width integer types for ecoff structs to make elf2ecoff work
on 64bit host machines.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19483/
Signed-off-by: Paul Burton <paul.burton@mips.com>
- Decrease polling rate for erase/trim/discard
- Allow non-sleeping GPIOs for card detect
- Improve mmc block removal path
- Enable support for mmc_sw_reset() for SDIO cards
- Add mmc_sw_reset() to allow users to do a soft reset of the card
- Allow power delay to be tunable via DT
- Allow card detect debounce delay to be tunable via DT
- Enable new quirk to limit clock rate for Marvell 8887 chip
- Don't show eMMC RPMB and BOOT areas in /proc/partitions
- Add capability to avoid 3.3V signaling for fragile HWs
MMC host:
- Improve/fixup support for handle highmem pages
- Remove depends on HAS_DMA in case of platform dependency
- mvsdio: Enable support for erase/trim/discard
- rtsx_usb: Enable support for erase/trim/discard
- renesas_sdhi: Fix WP logic regressions
- renesas_sdhi: Add r8a77965 support
- renesas_sdhi: Add R8A77980 to whitelist
- meson: Add optional support for device reset
- meson: Add support for the Meson-AXG platform
- dw_mmc: Add new driver for BlueField DW variant
- mediatek: Add support for 64G DRAM DMA
- sunxi: Deploy runtime PM support
- jz4740: Add support for JZ4780
- jz4740: Enable support for DT based platforms
- sdhci: Various improvement to timeout handling
- sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
- sdhci-omap: Add support for controller in k2g SoC
- sdhci-omap: Add workarounds for a couple of Erratas
- sdhci-omap: Enable support for generic sdhci DT properties
- sdhci-cadence: Re-send tune request to deal with errata
- sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
- sdhci-pci: Avoid 3.3V signaling on some NI 904x
- sdhci-esdhc-imx: Use watermark levels for PIO access
- sdhci-msm: Improve card detection handling
- sdhci-msm: Add support voltage pad switching
-----BEGIN PGP SIGNATURE-----
iQJLBAABCgA1FiEEugLDXPmKSktSkQsV/iaEJXNYjCkFAlsWMJUXHHVsZi5oYW5z
c29uQGxpbmFyby5vcmcACgkQ/iaEJXNYjCkWhw/9GdsKWGAezGYcBC9fBKVbZgvl
Mu7kTebyQy1N7kbIVD7sBz2ila1O2DhVI9SVS7lVhzFwrG4Hup0szb/mjEQgiOAi
+S2EjKRD3+9sA612fi1uWY+2cXoQiwCHhFZsCS5deL4pYspebzuYRNO5vZD7QlN8
vLHZ85yxBtMSiysDUTRm9MH2EXb9j6PfrHnVKj0ih112U/ip4PZVc7zHGBZq9zzy
6WSUMYBe2d1jajJ6MS3gf5Vrp53mz2OLkxKRCtMgut7YOwLZ8biKVa3G69ruQTm8
jqrMoNrZnhO3aT/1kassCE4ygoXewMZPhYq8k24PcaihR3o/tVI1dlb4Zz70cBb8
AGAdmdzu1sDEzY6KkSVTZ5IaxQo9SNANste/O/LfsOxHWkWxBQ6H0EeqMdt+W7of
A0zGKTQrcTFhxzA9OeX3aZwZhjcipQlf8TWnI5+ayPY/UKwMhvWNCTMQtTJAhqBh
mS7Uk5qd7OSJZTzVYrfLZ2ZOQKhtMbD9lAza/9Ldy5j5QDscLmxmhLOP0yuKI2Zp
92N3JPIGzfK4aKGCLKSA3KhYwuwaicwsXqfJV+cPz9fFtNs8WdHqyU+nslD0Oxm4
v3QZKPJa3LWCezPvWGSSTGLEgOvJtLQtJBefX1Hm6sxLbY12aBgu/iNp5UckGlzW
7zaWXtH8nzYlBKsXf/8=
=MwCT
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Decrease polling rate for erase/trim/discard
- Allow non-sleeping GPIOs for card detect
- Improve mmc block removal path
- Enable support for mmc_sw_reset() for SDIO cards
- Add mmc_sw_reset() to allow users to do a soft reset of the card
- Allow power delay to be tunable via DT
- Allow card detect debounce delay to be tunable via DT
- Enable new quirk to limit clock rate for Marvell 8887 chip
- Don't show eMMC RPMB and BOOT areas in /proc/partitions
- Add capability to avoid 3.3V signaling for fragile HWs
MMC host:
- Improve/fixup support for handle highmem pages
- Remove depends on HAS_DMA in case of platform dependency
- mvsdio: Enable support for erase/trim/discard
- rtsx_usb: Enable support for erase/trim/discard
- renesas_sdhi: Fix WP logic regressions
- renesas_sdhi: Add r8a77965 support
- renesas_sdhi: Add R8A77980 to whitelist
- meson: Add optional support for device reset
- meson: Add support for the Meson-AXG platform
- dw_mmc: Add new driver for BlueField DW variant
- mediatek: Add support for 64G DRAM DMA
- sunxi: Deploy runtime PM support
- jz4740: Add support for JZ4780
- jz4740: Enable support for DT based platforms
- sdhci: Various improvement to timeout handling
- sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
- sdhci-omap: Add support for controller in k2g SoC
- sdhci-omap: Add workarounds for a couple of Erratas
- sdhci-omap: Enable support for generic sdhci DT properties
- sdhci-cadence: Re-send tune request to deal with errata
- sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
- sdhci-pci: Avoid 3.3V signaling on some NI 904x
- sdhci-esdhc-imx: Use watermark levels for PIO access
- sdhci-msm: Improve card detection handling
- sdhci-msm: Add support voltage pad switching"
* tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (104 commits)
mmc: renesas_sdhi: really fix WP logic regressions
mmc: mvsdio: Enable MMC_CAP_ERASE
mmc: mvsdio: Respect card busy time out from mmc core
mmc: sdhci-msm: Remove NO_CARD_NO_RESET quirk
mmc: sunxi: Use ifdef rather than __maybe_unused
mmc: mxmmc: Use ifdef rather than __maybe_unused
mmc: mxmmc: include linux/highmem.h
mmc: sunxi: mark PM functions as __maybe_unused
mmc: Throttle calls to MMC_SEND_STATUS during mmc_do_erase()
mmc: au1xmmc: handle highmem pages
mmc: Allow non-sleeping GPIO cd
mmc: sdhci-*: Don't emit error msg if sdhci_add_host() fails
mmc: sd: Define name for default speed dtr
mmc: core: Move calls to ->prepare_hs400_tuning() closer to mmc code
mmc: sdhci-xenon: use match_string() helper
mmc: wbsd: handle highmem pages
mmc: ushc: handle highmem pages
mmc: mxcmmc: handle highmem pages
mmc: atmel-mci: use sg_copy_{from,to}_buffer
mmc: android-goldfish: use sg_copy_{from,to}_buffer
...
Add phy to switch port connections for PCB123 for internal PHYs.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Signed-off-by: James Hogan <jhogan@kernel.org>
Ocelot has an integrated switch, add support for it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Signed-off-by: James Hogan <jhogan@kernel.org>
- The previous node requested a memory area of 0x100 bytes, while the
driver only manipulates four registers present in the first 0x10 bytes.
- The driver requests for the "rtc" clock, but the previous node did not
provide any.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Mathieu Malaterre <malat@debian.org>
Acked-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: James Hogan <jhogan@kernel.org>
Also remove the watchdog platform_device from platform.c, since it
wasn't used anywhere anyway.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: linux-mips@linux-mips.org
Cc: linux-watchdog@vger.kernel.org
Cc: devicetree@vger.kernel.org
[jhogan@kernel.org: Drop jz4740_wdt_device declaration from header]
Signed-off-by: James Hogan <jhogan@kernel.org>
A dtb.o is generated from nexys4ddr.dts but this is never used since it
has been moved to mips/generic with commit b35565bb16 ("MIPS: generic:
Add support for MIPSfpga").
Fixes: b35565bb16 ("MIPS: generic: Add support for MIPSfpga")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.15+
Patchwork: https://patchwork.linux-mips.org/patch/19244/
Signed-off-by: James Hogan <jhogan@kernel.org>
The debug definitions were missing for MACH_JZ4770, resulting in a build
failure when DEBUG_ZBOOT was set.
Since the UART addresses are the same across all Ingenic SoCs, we just
use a #ifdef CONFIG_MACH_INGENIC instead of checking for individual
Ingenic SoCs.
Additionally, I added a #define for the UART0 address in-code and
dropped the <asm/mach-jz4740/base.h> include, for the reason that this
include file is slowly being phased out as the whole platform is being
moved to devicetree.
Fixes: 9be5f3e92e ("MIPS: ingenic: Initial JZ4770 support")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.16
Patchwork: https://patchwork.linux-mips.org/patch/18957/
Signed-off-by: James Hogan <jhogan@kernel.org>
Now that we have support for JZ480 SoCs in the MMC driver,
let's enable it on the devicetree.
Acked-by: James Hogan <jhogan@kernel.org>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add the devicetree node to support the MMC host controller
available in JZ480 SoCs.
Acked-by: James Hogan <jhogan@kernel.org>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add the devicetree node to support the DMA controller found
in JZ480 SoCs.
Tested-by: Mathieu Malaterre <malat@debian.org>
Acked-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for removing some of the MIPS compiler intrinsics from
arch/mips/lib, first update the build of vmlinuz to use the generic
ashldi3 from lib.
Both ashldi3 and bswapsi objects need to be built with different CFLAGS
for inclusion to vmlinuz rather than simply including the object built
for the main kernel image. The objects cannot be built directly from
source, since CONFIG_MODVERSIONS changes cmd_cc_o_c to prevent this.
Split the rule to ship ashldi3 and bswapsi from the relevant source
locations.
These files make no reference to other files in their directory, so the
additional CFLAGS are apparently unnecessary - remove them as well.
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19050/
[jhogan@kernel.org: Add if_changed and FORCE to fix build failure when
arch/mips/boot/compressed/ashldi3.c is already generated but there is
no .ashldi3.c.cmd file yet]
Signed-off-by: James Hogan <jhogan@kernel.org>
arch/mips/boot/dts/Makefile collects objects from sub-directories into
built-in.a only when CONFIG_BUILTIN_DTB is enabled. Reflect it also to
the sub-directory Makefiles. This suppresses unneeded built-in.a
creation in arch/mips/boot/dts/*/ directories.
While I am here, I replaced $(patsubst %.dtb, %.dtb.o, $(dtb-y)) with
$(addsuffix .o, $(dtb-y)) to simplify the code a little bit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/19099/
Signed-off-by: James Hogan <jhogan@kernel.org>
These are the main MIPS changes for 4.17. Rough overview:
(1) generic platform: Add support for Microsemi Ocelot SoCs
(2) crypto: Add CRC32 and CRC32C HW acceleration module
(3) Various cleanups and misc improvements
Miscellaneous:
- Hang more efficiently on halt/powerdown/restart
- pm-cps: Block system suspend when a JTAG probe is present
- Expand make help text for generic defconfigs
- Refactor handling of legacy defconfigs
- Determine the entry point from the ELF file header to fix microMIPS
for certain toolchains
- Introduce isa-rev.h for MIPS_ISA_REV and use to simplify other code
Minor cleanups:
- DTS: boston/ci20: Unit name cleanups and correction
- kdump: Make the default for PHYSICAL_START always 64-bit
- Constify gpio_led in Alchemy, AR7, and TXX9
- Silence a couple of W=1 warnings
- Remove duplicate includes
Platform support:
ath79:
- Fix AR724X_PLL_REG_PCIE_CONFIG offset
BCM47xx:
- FIRMWARE: Use mac_pton() for MAC address parsing
- Add Luxul XAP1500/XWR1750 WiFi LEDs
- Use standard reset button for Luxul XWR-1750
BMIPS:
- Enable CONFIG_BRCMSTB_PM in bmips_stb_defconfig for build coverage
- Add STB PM, wake-up timer, watchdog DT nodes
Generic platform:
- Add support for Microsemi Ocelot
- dt-bindings: Add vendor prefix for Microsemi Corporation
- dt-bindings: Add bindings for Microsemi SoCs
- Add ocelot SoC & PCB123 board DTS files
- MAINTAINERS: Add entry for Microsemi MIPS SoCs
- Enable crc32-mips on r6 configs
Octeon:
- Drop '.' after newlines in printk calls
ralink:
- pci-mt7621: Enable PCIe on MT7688
-----BEGIN PGP SIGNATURE-----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=4vUc
-----END PGP SIGNATURE-----
Merge tag 'mips_4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS updates from James Hogan:
"These are the main MIPS changes for 4.17. Rough overview:
(1) generic platform: Add support for Microsemi Ocelot SoCs
(2) crypto: Add CRC32 and CRC32C HW acceleration module
(3) Various cleanups and misc improvements
More detailed summary:
Miscellaneous:
- hang more efficiently on halt/powerdown/restart
- pm-cps: Block system suspend when a JTAG probe is present
- expand make help text for generic defconfigs
- refactor handling of legacy defconfigs
- determine the entry point from the ELF file header to fix microMIPS
for certain toolchains
- introduce isa-rev.h for MIPS_ISA_REV and use to simplify other code
Minor cleanups:
- DTS: boston/ci20: Unit name cleanups and correction
- kdump: Make the default for PHYSICAL_START always 64-bit
- constify gpio_led in Alchemy, AR7, and TXX9
- silence a couple of W=1 warnings
- remove duplicate includes
Platform support:
Generic platform:
- add support for Microsemi Ocelot
- dt-bindings: Add vendor prefix for Microsemi Corporation
- dt-bindings: Add bindings for Microsemi SoCs
- add ocelot SoC & PCB123 board DTS files
- MAINTAINERS: Add entry for Microsemi MIPS SoCs
- enable crc32-mips on r6 configs
ath79:
- fix AR724X_PLL_REG_PCIE_CONFIG offset
BCM47xx:
- firmware: Use mac_pton() for MAC address parsing
- add Luxul XAP1500/XWR1750 WiFi LEDs
- use standard reset button for Luxul XWR-1750
BMIPS:
- enable CONFIG_BRCMSTB_PM in bmips_stb_defconfig for build coverage
- add STB PM, wake-up timer, watchdog DT nodes
Octeon:
- drop '.' after newlines in printk calls
ralink:
- pci-mt7621: Enable PCIe on MT7688"
* tag 'mips_4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips: (37 commits)
MIPS: BCM47XX: Use standard reset button for Luxul XWR-1750
MIPS: BCM47XX: Add Luxul XAP1500/XWR1750 WiFi LEDs
MIPS: Make the default for PHYSICAL_START always 64-bit
MIPS: Use the entry point from the ELF file header
MAINTAINERS: Add entry for Microsemi MIPS SoCs
MIPS: generic: Add support for Microsemi Ocelot
MIPS: mscc: Add ocelot PCB123 device tree
MIPS: mscc: Add ocelot dtsi
dt-bindings: mips: Add bindings for Microsemi SoCs
dt-bindings: Add vendor prefix for Microsemi Corporation
MIPS: ath79: Fix AR724X_PLL_REG_PCIE_CONFIG offset
MIPS: pci-mt7620: Enable PCIe on MT7688
MIPS: pm-cps: Block system suspend when a JTAG probe is present
MIPS: VDSO: Replace __mips_isa_rev with MIPS_ISA_REV
MIPS: BPF: Replace __mips_isa_rev with MIPS_ISA_REV
MIPS: cpu-features.h: Replace __mips_isa_rev with MIPS_ISA_REV
MIPS: Introduce isa-rev.h to define MIPS_ISA_REV
MIPS: Hang more efficiently on halt/powerdown/restart
FIRMWARE: bcm47xx_nvram: Replace mac address parsing
MIPS: BMIPS: Add Broadcom STB watchdog nodes
...
Calling __stack_chk_guard_setup() in decompress_kernel() is too late
that stack checking always fails for decompress_kernel() itself. So
remove __stack_chk_guard_setup() and initialize __stack_chk_guard before
we call decompress_kernel().
Original code comes from ARM but also used for MIPS and SH, so fix them
together. If without this fix, compressed booting of these archs will
fail because stack checking is enabled by default (>=4.16).
Link: http://lkml.kernel.org/r/1522226933-29317-1-git-send-email-chenhc@lemote.com
Fixes: 8779657d29 ("stackprotector: Introduce CONFIG_CC_STACKPROTECTOR_STRONG")
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Acked-by: James Hogan <jhogan@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Rich Felker <dalias@libc.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a device tree include file for the Microsemi Ocelot SoC.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Allan Nielsen <Allan.Nielsen@microsemi.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/18855/
Signed-off-by: James Hogan <jhogan@kernel.org>
The MIPS %.its.S compiler command did not define __ASSEMBLY__, which meant
when compiler_types.h was added to kconfig.h, unexpected things appeared
(e.g. struct declarations) which should not have been present. As done in
the general %.S compiler command, __ASSEMBLY__ is now included here too.
The failure was:
Error: arch/mips/boot/vmlinux.gz.its:201.1-2 syntax error
FATAL ERROR: Unable to parse input tree
/usr/bin/mkimage: Can't read arch/mips/boot/vmlinux.gz.itb.tmp: Invalid argument
/usr/bin/mkimage Can't add hashes to FIT blob
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 28128c61e0 ("kconfig.h: Include compiler types to avoid missed struct attributes")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The unit name was 8c00000 but since the reg property is declared as:
reg = <0x0 0x4c00000 0x1 0xfb400000>;
the unit name should have been instead 4c00000.
Tested on MIPS Creator CI20 (v1):
$ cat /sys/firmware/devicetree/.../partitions/partition@4c00000/label;echo
system
Reported-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/18529/
Signed-off-by: James Hogan <jhogan@kernel.org>
Improve the DTS files by removing all the leading "0x" and zeros to fix
the following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +
For simplicity, two sed expressions were used to solve each warnings
separately.
To make the regex expression more robust a few other issues were
resolved, namely setting unit-address to lower case, and adding a
whitespace before the the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading
0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/18528/
Signed-off-by: James Hogan <jhogan@kernel.org>
The GCW Zero (http://www.gcw-zero.com) is a retro-gaming focused
handheld game console, successfully kickstarted in ~2012, running Linux.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18490/
Signed-off-by: James Hogan <jhogan@kernel.org>
Provide just enough bits (clocks, clocksource, uart) to allow a kernel
to boot on the JZ4770 SoC to a initramfs userspace.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Reviewed-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18487/
Signed-off-by: James Hogan <jhogan@kernel.org>
Make doesn't expand shell style "vmlinuz.{32,ecoff,bin,srec}" to the 4
separate files, so none of these files get cleaned up by make clean.
List the files separately instead.
Fixes: ec3352925b ("MIPS: Remove all generated vmlinuz* files on "make clean"")
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18491/
These are the main MIPS changes for 4.15.
Fixes:
- ralink: Fix MT7620 PCI build issues (4.5)
- Disable cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN for 32-bit SMP
(4.1)
- Fix MIPS64 FP save/restore on 32-bit kernels (4.0)
- ptrace: Pick up ptrace/seccomp changed syscall numbers (3.19)
- ralink: Fix MT7628 pinmux (3.19)
- BCM47XX: Fix LED inversion on WRT54GSv1 (3.17)
- Fix n32 core dumping as o32 since regset support (3.13)
- ralink: Drop obsolete USB_ARCH_HAS_HCD select
Build system:
- Default to "generic" (multiplatform) system type instead of IP22
- Use generic little endian MIPS32 r2 configuration as default defconfig
instead of ip22_defconfig
FPU emulation:
- Fix exception generation for certain R6 FPU instructions
SMP:
- Allow __cpu_number_map to be larger than NR_CPUS for sparse CPU id
spaces
Miscellaneous:
- Add iomem resource for kernel bss section for kexec/kdump
- Atomics: Nudge writes on bit unlock
- DT files: Standardise "ok" -> "okay"
Platform support:
BMIPS:
- Enable HARDIRQS_SW_RESEND
Broadcom BCM63XX:
- Add clkdev lookup support
- Update clk driver, UART driver, DTs to handle named refclk from DTs
- Split apart various clocks to more closely match hardware
- Add ethernet clocks
Cavium Octeon:
- Remove usage of cvmx_wait() in favour of __delay()
ImgTec Pistachio:
- DT: Drop deprecated dwmmc num-slots property
Ingenic JZ4780:
- Add NFS root to Ci20 defconfig
- Add watchdog to Ci20 DT & defconfig, and allow building of watchdog
driver with this SoC
Generic (multiplatform):
- Migrate xilfpga (MIPSfpga) platform to the generic platform
Lantiq xway:
- Fix ASC0/ASC1 clocks
Minor cleanups:
- Define virt_to_pfn()
- Make thread_saved_pc static
- Simplify 32-bit sign extension in __read_64bit_c0_split()
- DMA: Use vma_pages() helper
- FPU emulation: Replace unsigned with unsigned int
- MM: Removed unused lastpfn
- Alchemy: Make clk_ops const
- Lasat: Use setup_timer() helper
- ralink: Use BIT() in MT7620 PCI driver
-----BEGIN PGP SIGNATURE-----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=xbL0
-----END PGP SIGNATURE-----
Merge tag 'mips_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS updates from James Hogan:
"These are the main MIPS changes for 4.15.
Fixes:
- ralink: Fix MT7620 PCI build issues (4.5)
- Disable cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN for 32-bit SMP
(4.1)
- Fix MIPS64 FP save/restore on 32-bit kernels (4.0)
- ptrace: Pick up ptrace/seccomp changed syscall numbers (3.19)
- ralink: Fix MT7628 pinmux (3.19)
- BCM47XX: Fix LED inversion on WRT54GSv1 (3.17)
- Fix n32 core dumping as o32 since regset support (3.13)
- ralink: Drop obsolete USB_ARCH_HAS_HCD select
Build system:
- Default to "generic" (multiplatform) system type instead of IP22
- Use generic little endian MIPS32 r2 configuration as default
defconfig instead of ip22_defconfig
FPU emulation:
- Fix exception generation for certain R6 FPU instructions
SMP:
- Allow __cpu_number_map to be larger than NR_CPUS for sparse CPU id
spaces
Miscellaneous:
- Add iomem resource for kernel bss section for kexec/kdump
- Atomics: Nudge writes on bit unlock
- DT files: Standardise "ok" -> "okay"
Minor cleanups:
- Define virt_to_pfn()
- Make thread_saved_pc static
- Simplify 32-bit sign extension in __read_64bit_c0_split()
- DMA: Use vma_pages() helper
- FPU emulation: Replace unsigned with unsigned int
- MM: Removed unused lastpfn
- Alchemy: Make clk_ops const
- Lasat: Use setup_timer() helper
- ralink: Use BIT() in MT7620 PCI driver
Platform support:
BMIPS:
- Enable HARDIRQS_SW_RESEND
Broadcom BCM63XX:
- Add clkdev lookup support
- Update clk driver, UART driver, DTs to handle named refclk from DTs
- Split apart various clocks to more closely match hardware
- Add ethernet clocks
Cavium Octeon:
- Remove usage of cvmx_wait() in favour of __delay()
ImgTec Pistachio:
- DT: Drop deprecated dwmmc num-slots property
Ingenic JZ4780:
- Add NFS root to Ci20 defconfig
- Add watchdog to Ci20 DT & defconfig, and allow building of watchdog
driver with this SoC
Generic (multiplatform):
- Migrate xilfpga (MIPSfpga) platform to the generic platform
Lantiq xway:
- Fix ASC0/ASC1 clocks"
* tag 'mips_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips: (46 commits)
MIPS: Add iomem resource for kernel bss section.
MIPS: cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN don't work for 32-bit SMP
MIPS: BMIPS: Enable HARDIRQS_SW_RESEND
MIPS: pci: Make use of the BIT() macro inside the mt7620 driver
MIPS: pci: Remove KERN_WARN instance inside the mt7620 driver
MIPS: pci: Remove duplicate define in mt7620 driver
MIPS: ralink: Fix typo in mt7628 pinmux function
MIPS: ralink: Fix MT7628 pinmux
MIPS: Fix odd fp register warnings with MIPS64r2
watchdog: jz4780: Allow selection of jz4740-wdt driver
MIPS/ptrace: Update syscall nr on register changes
MIPS/ptrace: Pick up ptrace/seccomp changed syscalls
MIPS: Fix an n32 core file generation regset support regression
MIPS: Fix MIPS64 FP save/restore on 32-bit kernels
MIPS: page.h: Define virt_to_pfn()
MIPS: Xilfpga: Switch to using generic defconfigs
MIPS: generic: Add support for MIPSfpga
MIPS: Set defconfig target to a generic system for 32r2el
MIPS: Kconfig: Set default MIPS system type as generic
MIPS: DTS: Remove num-slots from Pistachio SoC
...
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing memory
leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node. The
prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to dtb
compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage Technology,
shimafuji, Tecon Microprocessor Technologies, DH electronics GmbH,
Opal Kelly, and Next Thing
-----BEGIN PGP SIGNATURE-----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=jgpN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
If CONFIG_OF_ALL_DTBS is enabled, "make ARCH=arm64 dtbs" compiles each
DTB twice; one from arch/arm64/boot/dts/*/Makefile and the other from
the dtb-$(CONFIG_OF_ALL_DTBS) line in arch/arm64/boot/dts/Makefile.
It could be a race problem when building DTBS in parallel.
Another minor issue is CONFIG_OF_ALL_DTBS covers only *.dts in vendor
sub-directories, so this broke when Broadcom added one more hierarchy
in arch/arm64/boot/dts/broadcom/<soc>/.
One idea to fix the issues in a clean way is to move DTB handling
to Kbuild core scripts. Makefile.dtbinst already recognizes dtb-y
natively, so it should not hurt to do so.
Add $(dtb-y) to extra-y, and $(dtb-) as well if CONFIG_OF_ALL_DTBS is
enabled. All clutter things in Makefiles go away.
As a bonus clean-up, I also removed dts-dirs. Just use subdir-y
directly to traverse sub-directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[robh: corrected BUILTIN_DTB to CONFIG_BUILTIN_DTB]
Signed-off-by: Rob Herring <robh@kernel.org>
arch/mips/boot/dts/brcm/bcm96358nb4ser.dts does not exist, so
we cannot build bcm96358nb4ser.dtb .
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fixes: 695835511f ("MIPS: BMIPS: rename bcm96358nb4ser to bcm6358-neufbox4-sercom")
Cc: stable@vger.kernel.org # 4.9+
Acked-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Add support for the MIPSfpga platform to generic kernel.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15846/
[jhogan@kernel.org: Use separate board-xilfpga.its.S. Add 32r2 and
little endian requires to board-xilfpga.config]
Signed-off-by: James Hogan <jhogan@kernel.org>
dwmmc driver deprecated num-slots and plan to get rid of it finally.
Just move a step to cleanup it from DT.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: James Hartley <james.hartley@sondrel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16741/
Signed-off-by: James Hogan <jhogan@kernel.org>
We need to add "clean-files" in Makfiles to clean up DT blobs, but we
often miss to do so.
Since there are no source files that end with .dtb or .dtb.S, so we
can clean-up those files from the top-level Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Most of DT files are compiled under arch/*/boot/dts/, but we have some
other directories, like drivers/of/unittest-data/. We often miss to
add gitignore patterns per directory. Since there are no source files
that end with .dtb or .dtb.S, we can ignore the patterns globally.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rob Herring <robh@kernel.org>
While the current kernel code in drivers/of/ allows developers to be
sloppy and use the status value "ok", the current DTSpec 0.1 makes it
clear that the only officially proper spelling is "okay", so adjust
the very small number of DTS files under arch/mips/.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17227/
Signed-off-by: James Hogan <jhogan@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add devicetree nodes for the DM9000 and the ethernet power regulator.
Additionally, add a new pinctrl node for the ethernet chip's pins.
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16752/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In preparation for splitting arch/mips/generic/vmlinux.its.S into
multiple files such that it doesn't become a conflict magnet as boards
are added, allow platforms to specify a list of image tree source files
which will be concatenated to form the final source used to build the
image tree.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16938/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"Boston platform support:
- Document DT bindings
- Add CLK driver for board clocks
CM:
- Avoid per-core locking with CM3 & higher
- WARN on attempt to lock invalid VP, not BUG
CPS:
- Select CONFIG_SYS_SUPPORTS_SCHED_SMT for MIPSr6
- Prevent multi-core with dcache aliasing
- Handle cores not powering down more gracefully
- Handle spurious VP starts more gracefully
DSP:
- Add lwx & lhx missaligned access support
eBPF:
- Add MIPS support along with many supporting change to add the
required infrastructure
Generic arch code:
- Misc sysmips MIPS_ATOMIC_SET fixes
- Drop duplicate HAVE_SYSCALL_TRACEPOINTS
- Negate error syscall return in trace
- Correct forced syscall errors
- Traced negative syscalls should return -ENOSYS
- Allow samples/bpf/tracex5 to access syscall arguments for sane
traces
- Cleanup from old Kconfig options in defconfigs
- Fix PREF instruction usage by memcpy for MIPS R6
- Fix various special cases in the FPU eulation
- Fix some special cases in MIPS16e2 support
- Fix MIPS I ISA /proc/cpuinfo reporting
- Sort MIPS Kconfig alphabetically
- Fix minimum alignment requirement of IRQ stack as required by
ABI / GCC
- Fix special cases in the module loader
- Perform post-DMA cache flushes on systems with MAARs
- Probe the I6500 CPU
- Cleanup cmpxchg and add support for 1 and 2 byte operations
- Use queued read/write locks (qrwlock)
- Use queued spinlocks (qspinlock)
- Add CPU shared FTLB feature detection
- Handle tlbex-tlbp race condition
- Allow storing pgd in C0_CONTEXT for MIPSr6
- Use current_cpu_type() in m4kc_tlbp_war()
- Support Boston in the generic kernel
Generic platform:
- yamon-dt: Pull YAMON DT shim code out of SEAD-3 board
- yamon-dt: Support > 256MB of RAM
- yamon-dt: Use serial* rather than uart* aliases
- Abstract FDT fixup application
- Set RTC_ALWAYS_BCD to 0
- Add a MAINTAINERS entry
core kernel:
- qspinlock.c: include linux/prefetch.h
Loongson 3:
- Add support
Perf:
- Add I6500 support
SEAD-3:
- Remove GIC timer from DT
- Set interrupt-parent per-device, not at root node
- Fix GIC interrupt specifiers
SMP:
- Skip IPI setup if we only have a single CPU
VDSO:
- Make comment match reality
- Improvements to time code in VDSO"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (86 commits)
locking/qspinlock: Include linux/prefetch.h
MIPS: Fix MIPS I ISA /proc/cpuinfo reporting
MIPS: Fix minimum alignment requirement of IRQ stack
MIPS: generic: Support MIPS Boston development boards
MIPS: DTS: img: Don't attempt to build-in all .dtb files
clk: boston: Add a driver for MIPS Boston board clocks
dt-bindings: Document img,boston-clock binding
MIPS: Traced negative syscalls should return -ENOSYS
MIPS: Correct forced syscall errors
MIPS: Negate error syscall return in trace
MIPS: Drop duplicate HAVE_SYSCALL_TRACEPOINTS select
MIPS16e2: Provide feature overrides for non-MIPS16 systems
MIPS: MIPS16e2: Report ASE presence in /proc/cpuinfo
MIPS: MIPS16e2: Subdecode extended LWSP/SWSP instructions
MIPS: MIPS16e2: Identify ASE presence
MIPS: VDSO: Fix a mismatch between comment and preprocessor constant
MIPS: VDSO: Add implementation of gettimeofday() fallback
MIPS: VDSO: Add implementation of clock_gettime() fallback
MIPS: VDSO: Fix conversions in do_monotonic()/do_monotonic_coarse()
MIPS: Use current_cpu_type() in m4kc_tlbp_war()
...
Add support for the MIPS Boston development board to generic kernels,
which essentially amounts to:
- Adding the device tree source for the MIPS Boston board.
- Adding a Kconfig fragment which enables the appropriate drivers for
the MIPS Boston board.
With these changes in place generic kernels will support the board by
default, and kernels with only the drivers needed for Boston enabled can
be configured by setting BOARDS=boston during configuration. For
example:
$ make ARCH=mips 64r6el_defconfig BOARDS=boston
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16485/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When building a FIT image we may want the kernel to build multiple .dtb
files, but we don't want to build them all into the kernel binary as
object files since they'll instead be included in the FIT image.
Commit daa10170da ("MIPS: DTS: img: add device tree for Marduk board")
however created arch/mips/boot/dts/img/Makefile with a line that builds
any enabled .dtb files into the kernel. Remove this & build the
pistachio object specifically, in preparation for adding .dtb targets
which we don't want to build into the kernel.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16484/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The various interrupt specifiers in the device tree are not in a valid
format for the MIPS GIC interrupt controller binding. Where each
interrupt should provide 3 values - GIC_LOCAL or GIC_SHARED, the
pin number & the type of interrupt - the device tree was only providing
the pin number. This causes interrupts for those devices to not be used
when a GIC is present. SEAD-3 systems without a GIC are unaffected since
the DT fixup code generates interrupt specifiers that are valid for the
CPU interrupt controller.
Fix this by adding the GIC_SHARED & IRQ_TYPE_LEVEL_HIGH values to each
interrupt specifier.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: c11e3b48db ("MIPS: SEAD3: Probe UARTs using DT")
Fixes: a34e93882d ("MIPS: SEAD3: Probe ethernet controller using DT")
Fixes: 7afd2a5aec ("MIPS: SEAD3: Probe EHCI controller using DT")
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v4.9+
Patchwork: https://patchwork.linux-mips.org/patch/16189/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The SEAD-3 board may be configured with or without a MIPS Global
Interrupt Controller (GIC). Because of this we have a device tree with a
default case of a GIC present, and code to fixup the device tree based
upon a configuration register that indicates the presence of the GIC.
In order to keep this DT fixup code simple, the interrupt-parent
property was specified at the root node of the SEAD-3 DT, allowing the
fixup code to simply change this property to the phandle of the CPU
interrupt controller if a GIC is not present & affect all
interrupt-using devices at once. This however causes a problem if we do
have a GIC & the device tree is used as-is, because the interrupt-parent
property of the root node applies to the CPU interrupt controller node.
This causes a cycle when of_irq_init() attempts to probe interrupt
controllers in order and boots fail due to a lack of configured
interrupts, with this message printed on the kernel console:
[ 0.000000] OF: of_irq_init: children remain, but no parents
Fix this by removing the interrupt-parent property from the DT root node
& instead setting it for each device which uses interrupts, ensuring
that the CPU interrupt controller node has no interrupt-parent &
allowing of_irq_init() to identify it as the root interrupt controller.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reported-by: Keng Koh <keng.koh@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16187/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Name aliases in the SEAD-3 device tree serial0 & serial1, rather than
uart0 & uart1. This allows the core serial code to make use of the
aliases to ensure that the UARTs are consistently numbered as expected
rather than having the numbering depend upon probe order.
When translating YAMON-provided serial configuration to a device tree
stdout-path property adjust accordingly, such that we continue to
reference a valid alias.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16183/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The SEAD-3 board doesn't & never has configured the GIC frequency.
Remove the timer node from the DT in order to avoid attempting to probe
the GIC clocksource/clockevent driver which will produce error messages
such as these during boot:
[ 0.000000] GIC frequency not specified.
[ 0.000000] Failed to initialize '/interrupt-controller@1b1c0000/timer': -22
[ 0.000000] clocksource_probe: no matching clocksources found
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16188/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The .its targets require information about the kernel binary, such as
its entry point, which is extracted from the vmlinux ELF. We therefore
require that the ELF is built before the .its files are generated.
Declare this requirement in the Makefile such that make will ensure this
is always the case, otherwise in corner cases we can hit issues as the
.its is generated with an incorrect (either invalid or stale) entry
point.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: cf2a5e0bb4 ("MIPS: Support generating Flattened Image Trees (.itb)")
Cc: linux-mips@linux-mips.org
Cc: stable <stable@vger.kernel.org> # v4.9+
Patchwork: https://patchwork.linux-mips.org/patch/16179/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We set the pin configuration for the jz4780-nand and jz4780-uart
drivers.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We set the pin configuration for the jz4740-nand, jz4740-mmc,
jz4740-fb, jz4740-pwm and jz4740-uart drivers.
This will permit those drivers to be cleaned out of the custom GPIO code
that they currently use.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For a description of the devicetree node, please read
Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt
For a description of the gpio devicetree nodes, please read
Documentation/devicetree/bindings/gpio/ingenic,gpio.txt
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For a description of the pinctrl devicetree node, please read
Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt
For a description of the gpio devicetree nodes, please read
Documentation/devicetree/bindings/gpio/ingenic,gpio.txt
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We use a directory under arch/$ARCH/boot/dts as an include path
that has links outside of the subtree to find dt-bindings from under
include/dt-bindings. That's been working well, but new DT architectures
haven't been adding them by default.
Recently there's been a desire to share some of the DT material between
arm and arm64, which originally caused developers to create symlinks or
relative includes between the subtrees. This isn't ideal -- it breaks
if the DT files aren't stored in the exact same hierarchy as the kernel
tree, and generally it's just icky.
As a somewhat cleaner solution we decided to add a $ARCH/ prefix link
once, and allow DTS files to reference dtsi (and dts) files in other
architectures that way.
Original approach was to create these links under each architecture,
but it lead to the problem of recursive symlinks.
As a remedy, move the include link directories out of the architecture
trees into a common location. At the same time, they can now share one
directory and one dt-bindings/ link as well.
Fixes: 4027494ae6 ('ARM: dts: add arm/arm64 include symlinks')
Reported-by: Russell King <linux@armlinux.org.uk>
Reported-by: Omar Sandoval <osandov@osandov.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: linux-arch <linux-arch@vger.kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
An img directory exists for the Pistchio SoC device tree but the
directory itself isn't in the dts Makefile meaning the dtbs never get
built.
Fixes: daa10170da ("MIPS: DTS: img: add device tree for Marduk board")
Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
Reviewed-by: Rahul Bedarkar <Rahul.Bedarkar@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15309/
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Al Viro noticed that we were using two different methods to filter out
flags from KBUILD_CFLAGS.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Add support for Imagination Technologies' Marduk board which is based
on Pistachio SoC. It is also known as Creator Ci40. Marduk is legacy
name and will be there for decades.
Documentation for this board can be found on
https://docs.creatordev.io/ci40/
This patch adds initial support for board with following peripherals:
* PWM based heartbeat LED
* GPIO based buttons
* SPI NOR flash on SPI1
* UART0 and UART1
* SD card
* Ethernet
* USB
* PWM
* ADC
* I2C
Signed-off-by: Rahul Bedarkar <rahul.bedarkar@imgtec.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: James Hartley <james.hartley@imgtec.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14394/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The make variables KBUILD_CFLAGS and KBUILD_AFLAGS both contain
$(LINUXINCLUDE). But the build already picks up $(LINUXINCLUDE) from
scripts/Makefile.lib. The net effect is that the (long) list of include
directories is used twice.
This is harmless but pointless. So stop using $(LINUXINCLUDE) twice.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14622/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
uzImage.bin is vmlinuz.bin wrapped in a legacy U-Boot image. Since
the extraction code is inside the image, it does not depend on the
boot loader to extract the kernel.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Cc: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14473/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Subsystem:
- non-modular drivers are now explicitly non-modular
New driver:
- Epson Toyocom rtc-7301sf/dg
Drivers:
- cmos: reject unsupported alarm values wrt the RTC capabilities
- ds1307: ACPI support
- jz4740: DT support, jz4780 handling, can now be used as a system power
controller
- mcp795: many fixes, in particular proper month handling
- twl: driver is now DT only
-----BEGIN PGP SIGNATURE-----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=z4SX
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- non-modular drivers are now explicitly non-modular
New driver:
- Epson Toyocom rtc-7301sf/dg
Drivers:
- cmos: reject unsupported alarm values wrt the RTC capabilities
- ds1307: ACPI support
- jz4740: DT support, jz4780 handling, can now be used as a system
power controller
- mcp795: many fixes, in particular proper month handling
- twl: driver is now DT only"
* tag 'rtc-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (31 commits)
rtc: mcp795: Fix whitespace and indentation.
rtc: mcp795: Prefer using the BIT() macro.
rtc: mcp795: fix month write resetting date to 1.
rtc: mcp795: fix time range difference between linux and RTC chip.
rtc: mcp795: fix bitmask value for leap year (LP).
rtc: mcp795: use bcd2bin/bin2bcd.
rtc: add support for EPSON TOYOCOM RTC-7301SF/DG
rtc: ds1307: Add ACPI support
rtc: imxdi: (trivial) fix a typo
rtc: ds1374: Merge conditional + WARN_ON()
rtc: twl: make driver DT only
rtc: twl: kill static variables
rtc: fix typos in Kconfig
rtc: jz4740: make the driver builtin only
rtc: jz4740: remove unused EXPORT_SYMBOL
Documentation: bindings: fix twl-rtc documentation
rtc: Enable compile testing for Maxim and Samsung drivers
MIPS: jz4740: Remove obsolete code
MIPS: qi_lb60: Probe RTC driver from DT and use it as power controller
MIPS: jz4740: DTS: Probe the jz4740-rtc driver from devicetree
...
Since we already have a devicetree node for the jz4740-rtc driver, we
don't have to probe it from platform code.
Besides, using the jz4740-rtc driver as the power controller for the
qi_lb60 platform allows us to remove the jz4740 platform power-off code,
since this is the only jz4740-based board upstream.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Now that the jz4740-rtc driver supports devicetree, we can add a
devicetree node for it.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Commit 10b6ea0959 ("MIPS: Malta: Use syscon-reboot driver to reboot")
converted the Malta board to use the generic syscon-reboot driver to
handle reboots, but incorrectly used the value 0x4d rather than 0x42 as
the magic to write to the reboot register.
I also incorrectly believed that syscon/regmap would default to native
endianness, but this isn't the case. Force this by specifying with a
native-endian property in the devicetree.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 10b6ea0959 ("MIPS: Malta: Use syscon-reboot driver to reboot")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: linux-mips@linux-mips.org
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Maciej W. Rozycki <macro@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/14396/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the MIPS SEAD-3 board support to be a generic board, supported
by generic kernels.
Because the SEAD-3 boot protocol was defined long ago and we don't want
to force a switch to the UHI protocol, SEAD-3 is added as a legacy board
which is detected by reading the REVISION register. This may technically
not be a valid memory read & future work will include attempting to
handle that gracefully. In practice since SEAD-3 is the only legacy
board supported by the generic kernel so far the read will only happen
on SEAD-3 boards, and even once Malta is converted the same REVISION
register exists there too. Other boards such as Boston, Ci20 & Ci40 will
use the UHI boot protocol & thus not run any of the legacy board detect
functions.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14354/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Introduce a "generic" platform, which aims to be board-agnostic by
making use of device trees passed by the boot protocol defined in the
MIPS UHI (Universal Hosting Interface) specification. Provision is made
for supporting boards which use a legacy boot protocol that can't be
changed, but adding support for such boards or any others is left to
followon patches.
Right now the built kernels expect to be loaded to 0x80100000, ie. in
kseg0. This is fine for the vast majority of MIPS platforms, but
nevertheless it would be good to remove this limitation in the future by
mapping the kernel via the TLB such that it can be loaded anywhere & map
itself appropriately.
Configuration is handled by dynamically generating configs using
scripts/kconfig/merge_config.sh, somewhat similar to the way powerpc
makes use of it. This allows for variations upon the configuration, eg.
differing architecture revisions or subsets of driver support for
differing boards, to be handled without having a large number of
defconfig files.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14353/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for generating kernel images in the Flattened Image Tree
(.itb) format as supported by U-Boot. This format is essentially a
Flattened Device Tree binary containing images (kernels, DTBs, ramdisks)
and configurations which link those images together. The big advantages
of FIT images over the uImage format are:
- We can include FDTs in the kernel image in a way that the bootloader
can extract it & manipulate it before providing it to the kernel.
Thus we can ship FDTs as part of the kernel giving us the advantages
of being able to develop & maintain the DT within the kernel tree,
but also have the benefits of the bootloader being able to
manipulate the FDT. Example uses for this would be to inject the
kernel command line into the chosen node, or to fill in the correct
memory size.
- We can include multiple configurations in a single kernel image.
This means that a single FIT image can, given appropriate
bootloaders, be booted on different boards with the bootloader
selecting an appropriate configuration & providing the correct FDT
to the kernel.
- We can support a multitude of hashes over the data.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14352/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make use of the generic syscon-reboot driver to reboot the Malta board,
reducing the amount of platform code it requires.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Stephan Linz <linz@li-pro.net>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14279/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add the DT nodes required to probe the CFI compatible parallel monitor
flash found on the Malta development board, and remove the platform
code that was previously doing it. Delete the now-empty malta-platform.c
file. Adjust the Malta defconfigs that enable MTD & the pflash/CFI
driver to enable CONFIG_MTD_PHYSMAP_OF rather than CONFIG_MTD_PHYSMAP in
order to preserve their behaviour.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14278/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe the CPU, GIC & i8259 interrupt controllers present in the Malta
system using device tree. This enables interrupts to be provided to
devices using device tree as they are moved over to being probed using
it.
Since Malta is very configurable it's unknown whether a GIC will be
present at compile time. In order to support both cases the
malta_dt_shim code is added in order to detect whether a GIC is present,
adjusting the DT to route interrupts correctly and nop out the GIC node
if no GIC is found.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14274/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe the img-ascii-lcd driver using device tree in order to display a
message on the SEAD3 board's LCD display, and remove the platform code
that was formerly performing this function. This removes more platform
code and moves SEAD3 further towards being entirely DT-based.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14063/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the custom platform code to restart when instructed to power off,
instead relying upon the generic restart-poweroff driver probed via DT
to do the same thing.
Remove also the halt implementation, which is incorrect. The generic
MIPS version will hang the system as halt should.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14057/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe a driver for the PLED & FLED LEDs found on the SEAD3 board using
the register-bit-led driver via device tree, rather than a custom driver
via platform code. Enable support for the register-bit-led driver & its
prerequisite syscon in sead3_defconfig.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14054/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe the SEAD3 EHCI controller using the generic-ehci driver & device
tree rather than platform code, in order to reduce the amount of the
latter.
Now that no devices probed from platform code require interrupts, remove
the retrieval of the IRQ domain & sead3int.h.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14051/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe the UARTs on SEAD3 boards using device tree rather than platform
code, in order to reduce the amount of the latter. This requires that
CONFIG_SERIAL_OF_PLATFORM be enabled, so enable it in sead3_defconfig.
The SEAD3 DT shim code is extended to read bootloader environment
variables to determine the appropriate UART & mode for kernel console
output & set the stdout-path property of the chosen node accordingly.
In contrast to the old platform code, which appears to have only ever
set "console=ttyS0,38400n8r" with the code in console_config never
having an effect, this will honor the "yamontty" environment variable to
select between the 2 UARTs on the board and then check the "modetty0" or
"modetty1" variable as appropriate to determine the UART configuration.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14048/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe the CPU interrupt controller & optional Global Interrupt
Controller (GIC) using devicetree rather than platform code. Because the
bootloader on SEAD3 does not provide a device tree to the kernel & the
device tree is always built in, we patch out the GIC node during boot if
we detect that a GIC is not present in the system.
The appropriate IRQ domain is discovered by platform code setting up
device IRQ numbers temporarily. It will be removed by further patches
which move the devices towards being probed via device tree.
No behavioural change is intended by this patch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14047/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When using clang as HOSTCC, the following warnings appear:
In file included from arch/mips/boot/tools/relocs_64.c:27:0:
arch/mips/boot/tools/relocs.c: In function ‘read_relocs’:
arch/mips/boot/tools/relocs.c:397:4: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
ELF_R_SYM(rel->r_info) = elf32_to_cpu(ELF_R_SYM(rel->r_info));
^~~~~~~~~
arch/mips/boot/tools/relocs.c:397:4: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
arch/mips/boot/tools/relocs.c: In function ‘walk_relocs’:
arch/mips/boot/tools/relocs.c:491:4: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
Elf_Sym *sym = &sh_symtab[ELF_R_SYM(rel->r_info)];
^~~~~~~
arch/mips/boot/tools/relocs.c: In function ‘do_reloc’:
arch/mips/boot/tools/relocs.c:502:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
unsigned r_type = ELF_R_TYPE(rel->r_info);
^~~~~~~~
arch/mips/boot/tools/relocs.c: In function ‘do_reloc_info’:
arch/mips/boot/tools/relocs.c:641:3: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
rel_type(ELF_R_TYPE(rel->r_info)),
^~~~~~~~
Fix them by making Elf64_Mips_Rela a union
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Acked-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13683/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of rewriting the arguments, just move the appended dtb to where
the decompressed kernel expects it. This eliminates the need for special
casing vmlinuz.bin appended dtb files.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: John Crispin <john@phrozen.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Alban Bedel <albeu@free.fr>
Cc: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13698/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Here is the quote from [1]:
The unit-address must match the first address specified
in the reg property of the node. If the node has no reg property,
the @ and unit-address must be omitted and the node-name alone
differentiates the node from other nodes at the same level
This patch adjusts MIPS dts-files and devicetree binding
documentation in accordance with [1].
[1] Power.org(tm) Standard for Embedded Power Architecture(tm)
Platform Requirements (ePAPR). Version 1.1 – 08 April 2011.
Chapter 2.2.1.1 Node Name Requirements
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13345/
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The DT fragment will select the ohci-platform driver, since that can
handle the JZ4740 OHCI just fine. While I don't have a JZ4740-based
board with anything connected to the USB host controller, I did test
the generic OHCI driver successfully on a JZ4770-based board.
The device is disabled by default; boards that want to use it can
override the "status" property. The mass-production Qi LB60 boards
don't use the USB host controller.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13104/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- now clock nodes definition is merged with core .dtsi file
- only one rootclk is now part of DT
- clock clients also updated based on new binding doc
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-clk@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13248/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fixes wrong bcm7425 SATA AHCI hardware interrupt property value with
periph_intc and SATA PHY unit address, and removes needless
brcm,broken-{ncq,phy} properties what are not used anywhere.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Dragan Stancevic <dragan.stancevic@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/13017/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This tool is based on the x86/boot/tools/relocs tool.
It parses the relocations present in the vmlinux elf file, building a
table of relocations that will be necessary to run the kernel from an
address other than its link address. This table is inserted into the
vmlinux elf, in the .data.relocs section. The table is subsequently used
by the code in arch/mips/kernel/relocate.c (added later) to relocate the
kernel.
The tool, by default, also marks all relocation sections as 0 length.
This is due to objcopy currently being unable to handle copying the
relocations between 64 and 32 bit elf files as is done when building a
64 bit kernel.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12981/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The following features are supported:
* UART;
* SPI-flash;
* USB host;
* GPIO key and LED.
Please see https://onion.io/omega for details.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Alban Bedel <albeu@free.fr>
Cc: L. D. Pinney <ldpinney@gmail.com>
Cc: Boken Lin <bl@onion.io>
Cc: Jacky Huang <huangfangcheng@163.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12884/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch introduces devicetree for Atheros AR9331 SoC (AKA Hornet).
The AR9331 chip is a Wi-Fi System-On-Chip (WiSOC),
typically used in very cheap Access Points and Routers.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12878/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Current ath79 clock.c code does not read reference clock and
pll setup from devicetree. E.g. you can set any clock rate value
in board DTS but it will have no effect on the real clk calculation.
This patch fixes some AR9132 devicetree clock support defects:
* clk initialization function ath79_clocks_init_dt_ng()
is introduced; it actually gets pll block base register
address and reference clock from devicetree;
* pll register parsing code is moved to the separate
ar724x_clk_init() function; this function
can be called from platform code or from devicetree code.
Also mips_hpt_frequency value is set from dt, so the appropriate
clock parameter is added to the cpu@0 devicetree node.
The same approach can be used for adding AR9331 devicetree support.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Alban Bedel <albeu@free.fr>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12876/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The include/dt-bindings/clock/ath79-clk.h header file
is introduced so we can use symbolic identifiers for SoC clocks.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Alban Bedel <albeu@free.fr>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-clk@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12875/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Here are some Sascha Hauer's arguments for using aliases in the dts
files:
- using aliases reduces the number of indentations in dts files;
- dts files become independent of the layout of the dtsi files
(it becomes possible to introduce another bus {} hierarchy between
a toplevel bus and the devices when you have to);
- less chances for typos. if &i2c2 does not exist you get an error.
If instead you duplicate the whole path in the dts file a typo
in the path will just create another node.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Cc: Alban Bedel <albeu@free.fr>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12873/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add DTS for EdgeRouter Lite that is usable as is without any "pruning"
with APPENDED_DTB.
Compared to builtin generic DTB, we can avoid errors and delays from
probing non-existent I2C devices.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Masahiro Yamada
Alexandre Belloni
Quentin Schulz
Alban Bedel
Mathieu Malaterre
Alexander Sverdlin
Thomas Bogendoerfer
Linus Torvalds
Paul Cercueil
Ezequiel Garcia
Matt Redfearn
Huacai Chen
Jaedon Shin
Kees Cook
James Hogan
Zubair Lutfullah Kakakhel
Shawn Lin
Robert P. J. Day
Jonas Gorski
Greg Kroah-Hartman
Harvey Hunt
Paul Burton
Nathan Sullivan
Bartosz Golaszewski
Linus Walleij
Olof Johansson
Ian Pozella
Ralf Baechle
Rahul Bedarkar
Paul Bolle
Maarten ter Huurne
Aaro Koskinen
Álvaro Fernández Rojas
Jonas Gorski
Antony Pavlov
Florian Fainelli
Purna Chandra Mandal
Matt Redfearn
Martin Schiller