The _none test is done differently for every level of the pagetable.
Standardize them by:
1: Use the native_X_val to extract the raw entry, with no need to go
via paravirt_ops, diff -r 1d0646d0d319 arch/x86/include/asm/pgtable.h, and
2: Compare with 0 rather than using a boolean !, since they are actually values
and not booleans.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Add pgd/pud/pmd_flags which are analogous to pte_flags, and use them
where-ever we only care about testing the flags portions of the
respective entries.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Impact: cleanup
Unify pmd_pfn. Unfortunately it can't be demacroed because it has a
cyclic dependency on linux/mm.h:page_to_nid().
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Taking sizeof the result of sizeof is quite strange and does not seem to be
what is wanted here.
This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression E;
@@
- sizeof (
sizeof (E)
- )
@@
type T;
@@
- sizeof (
sizeof (T)
- )
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is a simple change to correct problems when using set_irq_type
on platforms using CPM2. This code corrects the problem on most platform
but may have issues on 8272 derived platforms for some interrupts.
On 8272 PC2 & 3 are missing and PC 23 & 29 are added, which this patch
does not address.
Signed-off-by: Paul Bilke <paul@conspiracy.net>
Reviewed-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
TSEC0 is connected to Vitesse 7385 5-port switch. The switch
isn't connected to any mdio bus, the link to the switch is fixed
to Full-duplex 1000 Mb/s (no pause).
This patch fixes following failure during bootup:
mdio@24520:01 not found
eth0: Could not attach to PHY
IP-Config: Failed to open eth0
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit b31a1d8b41 ("gianfar: Convert
gianfar to an of_platform_driver") introduced a child node for
the ethernet@25000 controller, but no address and size cells
specifiers were added, and that makes dtc unhappy:
DTC: dts->dtb on file "arch/powerpc/boot/dts/mpc8313erdb.dts"
Warning (reg_format): "reg" property in /soc8313@e0000000/ethernet@25000/mdio@25520 has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc8313@e0000000/ethernet@25000/mdio@25520
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc8313@e0000000/ethernet@25000/mdio@25520
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
I noticed this doing some randconfig testing (.config below). I have
CONFIG_PM but no CONFIG_SUSPEND. Bug is against mainline.
arch/powerpc/sysdev/built-in.o: In function `ipic_suspend':
ipic.c:(.text+0x6b34): undefined reference to `fsl_deep_sleep'
make[1]: *** [.tmp_vmlinux1] Error 1
make: *** [sub-make] Error 2
Looks like #ifdef CONFIG_PM in arch/powerpc/sysdev/ipic.c should be
CONFIG_SUSPEND. d49747bdfb introduced
this.
Fix build when we have CONFIG_PM but no CONFIG_SUSPEND.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Implement Linus's suggestion: introduce the hpet_cnt_ahead()
helper function to compare hpet time values - like other
wrapping counter comparisons are abstracted away elsewhere.
(jiffies, ktime_t, etc.)
Reported-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
They can't be used for profiling and NMI watchdog currently
since they lack the counter overflow interrupt.
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent kprobes from catching spurious faults which will cause infinite
recursive page-fault and memory corruption by stack overflow.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: <stable@kernel.org> [2.6.28.x]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'sh/for-2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix up T-bit error handling in SH-4A mutex fastpath.
sh: Fix up spurious syscall restarting.
sh: fcnvds fix with denormalized numbers on SH-4 FPU.
sh: Only reserve memory under CONFIG_ZERO_PAGE_OFFSET when it != 0.
sh: Handle calling csum_partial with misaligned data
sh: ap325rxa: Enable ov772x in defconfig.
sh: ap325rxa: Add ov772x support.
sh: ap325rxa: control camera power toggling.
sh: mach-migor: Enable ov772x and tw9910 in defconfig.
- Consistent alignment of help text
- Use the ---help--- keyword everywhere consistently as a visual separator
- fix whitespace mismatches
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
only leave _default_ipi_xx etc in .h
Beyond the cleanup factor, this saves a bit of code size as well:
text data bss dec hex filename
7281931 1630144 1463304 10375379 9e50d3 vmlinux.before
7281753 1630144 1463304 10375201 9e5021 vmlinux.after
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
disable_ioapic_setup() in init/main.c is ugly as the function is
x86-specific. The #ifdef inline prototype there is ugly too.
Replace it with a generic arch_disable_smp_support() function - which
has a weak alias for non-x86 architectures and for non-ioapic x86 builds.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Do usual do {} while (0) dance, otherwise
fs/gfs2/util.c:99: error: expected expression before 'else'
drivers/scsi/lpfc/lpfc_sli.c:363: error: expected expression before 'else'
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the following style cleanups:
* drop unnecessary //#include from xen-asm_32.S
* compulsive adding of space after comma
* reformat multiline comments
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
At this time, the PowerNow! driver for K8 uses an experimentally
derived formula to calculate transition latency. The value it
provides is orders of magnitude too large on modern systems.
This patch replaces the formula with ACPI _PSS latency values
for more accuracy and better performance.
I've tested it on two 2nd generation Opteron systems, a 3rd
generation Operton system, and a Turion X2 without seeing any
stability problems.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Due to recurring issues with DMAR support on certain platforms.
There's a number of filesystem corruption incidents reported:
https://bugzilla.redhat.com/show_bug.cgi?id=479996http://bugzilla.kernel.org/show_bug.cgi?id=12578
Provide a Kconfig option to change whether it is enabled by
default.
If disabled, it can still be reenabled by passing intel_iommu=on to the
kernel. Keep the .config option off by default.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On an x86 system which doesn't support global mappings,
__supported_pte_mask has _PAGE_GLOBAL clear, to make sure it never
appears in the PTE. pfn_pte() and so on will enforce it with:
static inline pte_t pfn_pte(unsigned long page_nr, pgprot_t pgprot)
{
return __pte((((phys_addr_t)page_nr << PAGE_SHIFT) |
pgprot_val(pgprot)) & __supported_pte_mask);
}
However, we overload _PAGE_GLOBAL with _PAGE_PROTNONE on non-present
ptes to distinguish them from swap entries. However, applying
__supported_pte_mask indiscriminately will clear the bit and corrupt the
pte.
I guess the best fix is to only apply __supported_pte_mask to present
ptes. This seems like the right solution to me, as it means we can
completely ignore the issue of overlaps between the present pte bits and
the non-present pte-as-swap entry use of the bits.
__supported_pte_mask contains the set of flags we support on the
current hardware. We also use bits in the pte for things like
logically present ptes with no permissions, and swap entries for
swapped out pages. We should only apply __supported_pte_mask to
present ptes, because otherwise we may destroy other information being
stored in the ptes.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: cleanup
In __put_user_size() macro errret is used for error value.
But if size is 8, errret isn't passed to__put_user_asm_u64().
This behavior is inconsistent.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Enable the use of the direct vcpu-access operations on 64-bit.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Now that x86-64 has directly accessible percpu variables, it can also
implement the direct versions of these operations, which operate on a
vcpu_info structure directly embedded in the percpu area.
In fact, the 64-bit versions are more or less identical, and so can be
shared. The only two differences are:
1. xen_restore_fl_direct takes its argument in eax on 32-bit, and rdi on 64-bit.
Unfortunately it isn't possible to directly refer to the 2nd lsb of rdi directly
(as you can with %ah), so the code isn't quite as dense.
2. check_events needs to variants to save different registers.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
We need to access percpu data fairly early, so set up the percpu
registers as soon as possible. We only need to load the appropriate
segment register. We already have a GDT, but its hard to change it
early because we need to manipulate the pagetable to do so, and that
hasn't been set up yet.
Also, set the kernel stack when bringing up secondary CPUs. If we
don't they all end up sharing the same stack...
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This patch makes the ROM reading code return an error to user space if
the size of the ROM read is equal to 0.
The patch also emits a warnings if the contents of the ROM are invalid,
and documents the effects of the "enable" file on ROM reading.
Signed-off-by: Timothy S. Nelson <wayland@wayland.id.au>
Acked-by: Alex Villacis-Lasso <a_villacis@palosanto.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Moving the mmu code from enlighten.c to mmu.c inadvertently broke the
32-bit build. Fix it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: cleanup
Introduce helper function fault_in_kernel_address() to make editors happy.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
There's a small problem with hpet_rtc_reinit function - it checks
for the:
hpet_readl(HPET_COUNTER) - hpet_t1_cmp > 0
to continue increasing both the HPET_T1_CMP (register) and the
hpet_t1_cmp (variable).
But since the HPET_COUNTER is always 32-bit, if the hpet_t1_cmp
is 64-bit this condition will always be FALSE once the latter hits
the 32-bit boundary, and we can have a situation, when we don't
increase the HPET_T1_CMP register high enough.
The result - timer stops ticking, since HPET_T1_CMP becomes less,
than the COUNTER and never increased again.
The solution is (based on Linus's suggestion) to not compare 64-bits
(on 64-bit x86), but to do the comparison on 32-bit signed
integers.
Reported-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: APIC: enable workaround on AMD Fam10h CPUs
xen: disable interrupts before saving in percpu
x86: add x86@kernel.org to MAINTAINERS
x86: push old stack address on irqstack for unwinder
irq, x86: fix lock status with numa_migrate_irq_desc
x86: add cache descriptors for Intel Core i7
x86/Voyager: make it build and boot
Impact: cleanup
Some lines exceed the 80 char width making them unreadable.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch echoes what we already do on 32-bit since
90f7d25c6b, and prints the DMI
product name in show_regs, so that system specific problems can be
easily identified.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (40 commits)
Blackfin arch: Remove outdated code
Blackfin arch: Fix udelay implementation
Blackfin arch: Update Copyright information
Blackfin arch: Add BF561 PPI POLS, POLC Masks
Blackfin arch: Update CM-BF527 kernel config
Blackfin arch: define bfin_memmap as static since it is only used here
Blackfin arch: cplb mananger: use a do...while loop rather than a for loop
Blackfin arch: fix bug - traps test case 19 for exception 0x2d fails
Blackfin arch: add platform device bfin_mii-bus and KSZ8893M switch driver platform resources to board files
Blackfin arch: build jtag tty driver as a module by default
Blackfin arch: fix 2 bugs related to debug
Blackfin arch: Add ANOMALY_05000380 to BF54x to kill the compile warning
Blackfin arch: Fix bug - 561 SMP kernel can't boot from jffs2
Blackfin arch: base SIC_IWR# programming on whether the MMR exists
Blackfin arch: read SYSCR on newer parts that mirror the bits of SWRST in it
Blackfin arch: fixup board init function name
Blackfin arch: drop CONFIG_I2C_BOARDINFO ifdefs
Blackfin arch: bfin_reset->_bfin_reset redirection no longer needed
Blackfin arch: sync reboot handler with version in u-boot
Blackfin arch: Faster Implementation of csum_tcpudp_nofold()
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Kill bogus TPC/address truncation during 32-bit faults.
sparc: fixup for sparseirq changes
sparc64: Validate kernel generated fault addresses on sparc64.
sparc64: On non-Niagara, need to touch NMI watchdog in NOHZ mode.
sparc64: Implement NMI watchdog on capable cpus.
sparc: Probe PMU type and record in sparc_pmu_type.
sparc64: Move generic PCR support code to seperate file.
The removed version with the loop registers saved on the stack was
originally intended to workaround the missing toolchain support for
LoopReg Clobbers.
Since our toolchain now supports these there is no point in keeping this
workaround. And since we don't touch LoopRegs anymore we're no longer
subject for ANOMALY_05000312.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Avoid possible overflow during 32*32->32 multiplies.
Reported-by: Marco Reppenhagen <marco.reppenhagen@auerswald.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
use a do...while loop rather than a for loop to get slightly better
optimization and to avoid gcc "may be used uninitialized" warnings ...
we know that the [id]cplb_nr_bounds variables will never be 0, so this
is OK
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Enable null pointer checking for ICPLBs. The code was there but for
some reason I had commented it out at some stage during development.
Should restrict this to 1K since atomic ops start there.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
- unable to single step over emuexcpt instruction
- gdbproxy goes into infinite loop when doing gdb does "next" over
"emuexcpt"
Don't decrement PC after software breakpoint.
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
bss_l2 section is garbage when the data in this section is used by
_bfin_relocate_l1_mem, so move the zero out function ahead.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
base SIC_IWR# programming on whether the MMR exists
rather than having to maintain another list of processors
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Drop CONFIG_I2C_BOARDINFO ifdefs as the common i2c header handles this
already by stubbing things out
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Avoid conditional branch instructions during carry bit additions.
Special thanks to Bernd.
Simplify: Use ((len + proto) << 8) like every other __LITTLE_ENDIAN__ machine
Cc: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[Mike Frysinger <vapier.adi@gmail.com>:
- setup P_DEFAULT_BOOT_SPI_CS for every arch based on
the default bootrom behavior and convert all our boards
to it
- revert previous anomaly change ... bf51x is not affected
by anomaly 05000353]
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
merge more of the bf54x and !bf54x gpio code together to
cut down on #ifdef mess
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
According to the documentation gpio_free should only be called from task
context only. To make this more explicit add a might sleep to all
implementations.
This patch changes the gpio_free implementations for the blackfin
architecture.
Signed-off-by: Uwe Kleine-Koenig <ukleinek@strlen.de>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Make sure we don't accidently re-enable interrupts if we are being
called in atomic context
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
when requesting a GPIO for the first time, the POLAR setting is not
set to a sane state. this can lead to indeterminate behavior that
cannot be resolved without an explicit write to the Blackfin port POLAR
register.
when requesting a GPIO for the first time via gpio_request(), the POLAR
setting for the GPIO in question should be set to sane state. this
should occur if the GPIO has not been allocated in any other way.
some examples:
- when doing something like "request_irq(); gpio_request();" on the
same GPIO, the POLAR setting should not be reset.
- when doing "gpio_request(); gpio_request();" on the same GPIO, the
POLAR setting should be reset only the first time and not the second.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
On BF561 EBIU_SDGCTL bit 31 controls the SDRAM external data
path width, typically set 0 for a 32-bit bus width. On other
Blackfin derivatives this bit should be set by default.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Dmacopy failed in BF537-STAMP when copy from SRAM to SDRAM and kernel
will reboot automatically.
Fixing by doing a SSYNC before mucking with DMA registers
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
They were long enough set deprecated...
Update Documentation/cpu-freq/users-guide.txt:
The deprecated files listed there seen not to exist for some time anymore
already.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Impact: reduce kernel BSS size by 7 pages, improve code readability
Two page tables are used in current x86_64 kexec implementation. One
is used to jump from kernel virtual address to identity map address,
the other is used to map all physical memory. In fact, on x86_64,
there is no conflict between kernel virtual address space and physical
memory space, so just one page table is sufficient. The page table
pages used to map control page are dynamically allocated to save
memory if kexec image is not loaded. ASM code used to map control page
is replaced by C code too.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: fix to enable APIC for AMD Fam10h on chipsets with a missing/b0rked
ACPI MP table (MADT)
Booting a 32bit kernel on an AMD Fam10h CPU running on chipsets with
missing/b0rked MP table leads to a hang pretty early in the boot process
due to the APIC not being initialized. Fix that by falling back to the
default APIC base address in 32bit code, as it is done in the 64bit
codepath.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: Fix race condition
xen_mc_batch has a small preempt race where it takes the address of a
percpu variable immediately before disabling interrupts, thereby
leaving a small window in which we may migrate to another cpu and save
the flags in the wrong percpu variable. Disable interrupts before
saving the old flags in a percpu.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This builds upon eeabac7386
("sparc64: Validate kernel generated fault addresses on sparc64.")
Upon further consideration, we actually should never see any
fault addresses for 32-bit tasks with the upper 32-bits set.
If it does every happen, by definition it's a bug. Whatever
context created that fault would only have that fault satisfied
if we used the full 64-bit address. If we truncate it, we'll
always fault the wrong address and we'll always loop faulting
forever.
So catch such conditions and mark them as errors always. Log
the error and fail the fault.
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Bug fix
A hunk went missing in the original patch, and callee-save callsites were
not marked as returning the upper 32-bit of result, causing Badness.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
In order to handle all of the cases of address calculation overflow
properly, we run sparc 32-bit processes in "address masking" mode
when running on a 64-bit kernel.
Address masking mode zeros out the top 32-bits of the address
calculated for every load and store instruction.
However, when we're in privileged mode we have to run with that
address masking mode disabled even when accessing userspace from
the kernel.
To "simulate" the address masking mode we clear the top-bits by
hand for 32-bit processes in the fault handler.
It is the responsibility of code in the compat layer to properly
zero extend addresses used to access userspace. If this isn't
followed properly we can get into a fault loop.
Say that the user address is 0xf0000000 but for whatever reason
the kernel code sign extends this to 64-bit, and then the kernel
tries to access the result.
In such a case we'll fault on address 0xfffffffff0000000 but the fault
handler will process that fault as if it were to address 0xf0000000.
We'll loop faulting forever because the fault never gets satisfied.
So add a check specifically for this case, when the kernel is faulting
on a user address access and the addresses don't match up.
This code path is sufficiently slow path, and this bug is sufficiently
painful to diagnose, that this kind of bug check is warranted.
Signed-off-by: David S. Miller <davem@davemloft.net>
When we're idling in NOHZ mode, timer interrupts are not running.
Evidence of processing timer interrupts is what the NMI watchdog
uses to determine if the CPU is stuck.
On Niagara, we'll yield the cpu. This will make the cpu, at
worst, hang out in the hypervisor until an interrupt arrives.
This will prevent the NMI watchdog timer from firing.
However on non-Niagara we just loop executing instructions
which will cause the NMI watchdog to keep firing. It won't
see timer interrupts happening so it will think the cpu is
stuck.
Fix this by touching the NMI watchdog in the cpu idle loop
on non-Niagara machines.
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Fixes dumpstack and KDB on 64 bits
This re-adds the old stack pointer to the top of the irqstack to help
with unwinding. It was removed in commit d99015b1ab
as part of the save_args out-of-line work.
Both dumpstack and KDB require this information.
Signed-off-by: Martin Hicks <mort@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI hotplug: Change link order of pciehp & acpiphp
PCI hotplug: fakephp: Allocate PCI resources before adding the device
PCI MSI: Fix undefined shift by 32
PCI PM: Do not wait for buses in B2 or B3 during resume
PCI PM: Power up devices before restoring their state
PCI PM: Fix hibernation breakage on EeePC 701
PCI: irq and pci_ids patch for Intel Tigerpoint DeviceIDs
PCI PM: Fix suspend error paths and testing facility breakage
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
fbdev/atyfb: Fix DSP config on some PowerMacs & PowerBooks
powerpc: Fix oops on some machines due to incorrect pr_debug()
powerpc/ps3: Printing fixups for l64 to ll64 convserion drivers/net
powerpc/5200: update device tree binding documentation
powerpc/5200: Bugfix for PCI mapping of memory and IMMR
powerpc/5200: update defconfigs
When probing the keyboard controller to enable A20, if we get FF back
(which is *possible* as a valid status word, but is extremely
unlikely) then bail after much fewer iterations than we otherwise
would, and abort the attempt to access the KBC.
This hopefully should make it work a lot better for embedded platforms
which don't have a KBC and where the BIOS doesn't implement
INT 15h AX=2401h (and doesn't boot with A20 already enabled.)
If this works, it will be the one remaining use of CONFIG_X86_ELAN as
anything other than a processor type optimization option.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This patch adds a MX2/MX3 specific SDHC driver. The hardware is basically
the same as in the MX1, but unlike the MX1 controller the MX2
controller just works as expected. Since the MX1 driver has more
workarounds for bugs than anything else I had no success with supporting
MX1 and MX2 in a sane way in one driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
fix the following 'make headers_check' warning:
usr/include/asm/setup.h:16: extern's make no sense in userspace
usr/include/asm/setup.h:17: extern's make no sense in userspace
usr/include/asm/setup.h:23: extern's make no sense in userspace
usr/include/asm/setup.h:24: extern's make no sense in userspace
usr/include/asm/setup.h:51: extern's make no sense in userspace
usr/include/asm/setup.h:52: extern's make no sense in userspace
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warning:
usr/include/asm/prctl.h:10: extern's make no sense in userspace
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Zach says:
> Enable/Disable have no clobbers at all.
> Save clobbers only return value, %eax
> Restore also clobbers nothing.
This is precisely compatible with the calling convention, so we can
just call them directly without wrapping.
(Compile tested only.)
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: bugfix
In the 32-bit calling convention, %eax:%edx is used to return 64-bit
values. Don't save and restore %edx around wrapped functions, or they
can't return a full 64-bit result.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Recently, a patch left DEBUG enabled in the powerpc common PCI code,
resulting in an old bug in a pr_debug() statement to show up and cause
a NULL dereference on some machines.
This fixes the pr_debug() statement and reverts to DEBUG not being
force-enabled in that file.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Eric Paris reported:
> I have an hp dl785g5 which is unable to successfully run
> 2.6.29-0.66.rc3.fc11.x86_64 or 2.6.29-rc2-next-20090126. During bootup
> (early in userspace daemons starting) I get the below BUG, which quickly
> renders the machine dead. I assume it is because sparse_irq_lock never
> gets released when the BUG kills that task.
Adjust lock sequence when migrating a descriptor with
CONFIG_NUMA_MIGRATE_IRQ_DESC enabled.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix the following 'make headers_check' warnings:
usr/include/asm-xtensa/swab.h:14: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-xtensa/swab.h:19: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warning:
usr/include/asm-powerpc/swab.h:11: include of <linux/types.h> is preferred over <asm/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warning:
usr/include/asm-powerpc/spu_info.h:27: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warning:
usr/include/asm-powerpc/ps3fb.h:33: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/asm-powerpc/kvm.h:23: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-powerpc/kvm.h:26: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warning:
usr/include/asm-powerpc/elf.h:5: include of <linux/types.h> is preferred over <asm/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/asm-powerpc/bootx.h:12: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-powerpc/bootx.h:57: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/asm-parisc/swab.h:4: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-parisc/swab.h:9: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warning:
usr/include/asm-parisc/pdc.h:420: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/asm-mips/swab.h:12: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-mips/swab.h:18: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warning:
usr/include/asm-mips/sigcontext.h:57: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/asm-ia64/swab.h:9: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-ia64/swab.h:13: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/asm-ia64/kvm.h:24: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-ia64/kvm.h:34: found __[us]{8,16,32,64} type without #include <linux/types.h
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warning:
usr/include/asm-ia64/intrinsics.h:57: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warning:
usr/include/asm-ia64/gcc_intrin.h:63: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warning:
usr/include/asm-ia64/fpu.h:9: include of <linux/types.h> is preferred over <asm/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warning:
usr/include/asm-h8300/swab.h:4: include of <linux/types.h> is preferred over <asm/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/asm-blackfin/swab.h:4: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-blackfin/swab.h:13: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/asm-avr32/swab.h:7: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-avr32/swab.h:22: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/asm-arm/swab.h:19: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-arm/swab.h:25: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/asm-arm/setup.h:17: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-arm/setup.h:25: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/asm-arm/a.out.h:5: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-arm/a.out.h:9: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/asm-alpha/swab.h:4: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-alpha/swab.h:10: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warning:
usr/include/asm-alpha/statfs.h:6: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, ds, bts: cleanup/fix DS configuration
ring-buffer: reset timestamps when ring buffer is reset
trace: set max latency variable to zero on default
trace: stop all recording to ring buffer on ftrace_dump
trace: print ftrace_dump at KERN_EMERG log level
ring_buffer: reset write when reserve buffer fail
tracing/function-graph-tracer: fix a regression while suspend to disk
ring-buffer: fix alignment problem
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 setup: fix asm constraints in vesa_store_edid
xen: make sysfs files behave as their names suggest
x86: tone down mtrr_trim_uncached_memory() warning
x86: correct the CPUID pattern for MSR_IA32_MISC_ENABLE availability
[
mingo@elte.hu: these fixes are a subset of changes cherry-picked from:
git://git.kernel.org:/pub/scm/linux/kernel/git/jejb/voyager-2.6.git
They fix various problems that recent x86 changes caused in the Voyager
subarchitecture: both APIC changes and cpumask changes and certain
cleanups caused subarch assumptions to break.
Most of these changes are obsolete as the subarch code has been removed
from the x86 development tree - but we merge them upstream to make Voyager
build and boot.
]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix xen booting
We need to access percpu data fairly early, so set up the percpu
registers as soon as possible. We only need to load the appropriate
segment register. We already have a GDT, but its hard to change it
early because we need to manipulate the pagetable to do so, and that
hasn't been set up yet.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: split out a function, no functional change
Xen needs to be able to access percpu data from very early on. For
various reasons, it cannot also load the gdt at that time. It does,
however, have a pefectly functional gdt at that point, so there's no
pressing need to reload the gdt.
Split the function to load the segment registers off, so Xen can call
it directly.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: cleanup, prepare for xen boot fix.
Xen needs to call this function very early to setup the GDT and
per-cpu segments. Remove the call to smp_processor_id() and just
pass in the cpu number.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: fix possible tlb mis-flushing on UV
uv_flush_send_and_wait() should return a pointer if the broadcast
remote tlb shootdown requests fail. That causes the conventional IPI
method of shootdown to be used.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Most of the vector layout on 32-bit and 64-bit is identical now,
so eliminate the duplicated enumeration of the vectors.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a slot for the performance monitoring interrupt. Not yet used
by any subsystem - but the hardware has it. (This eases integration
with performance monitoring code.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
"flash" is a very generic name for a platform_driver that is only
available on SA11x0.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Nicolas Pitre <nico@marvell.com>
SPIN_LOCK_UNLOCKED is deprecated as lockdep cannot properly work with
locks initialized with it.
This fix is necessary to compile the linux-rt tree for ARM.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Steven Rostedt <srostedt@redhat.com>
Impact: fix potential miscompile (currently believed non-manifest)
As the comment explains, the VBE DDC call can clobber any register.
Tell the compiler about that fact.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: Fix build when CONFIG_PARAVIRT_DEBUG is enabled
Fix missed convertion to using callee-saved calls for pud_val, which
causes a compile error when CONFIG_PARAVIRT_DEBUG is enabled.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: Optimization
In the native case, pte_val, make_pte, etc are all just identity
functions, so there's no need to clobber a lot of registers over them.
(This changes the 32-bit callee-save calling convention to return both
EAX and EDX so functions can return 64-bit values.)
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: Optimization
Functions with the callee save calling convention clobber many fewer
registers than the normal C calling convention. Implement variants of
PVOP_V?CALL* accordingly. This only bothers with functions up to 3
args, since functions with more args may as well use the normal
calling convention.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: Optimization
One of the problems with inserting a pile of C calls where previously
there were none is that the register pressure is greatly increased.
The C calling convention says that the caller must expect a certain
set of registers may be trashed by the callee, and that the callee can
use those registers without restriction. This includes the function
argument registers, and several others.
This patch seeks to alleviate this pressure by introducing wrapper
thunks that will do the register saving/restoring, so that the
callsite doesn't need to worry about it, but the callee function can
be conventional compiler-generated code. In many cases (particularly
performance-sensitive cases) the callee will be in assembler anyway,
and need not use the compiler's calling convention.
Standard calling convention is:
arguments return scratch
x86-32 eax edx ecx eax ?
x86-64 rdi rsi rdx rcx rax r8 r9 r10 r11
The thunk preserves all argument and scratch registers. The return
register is not preserved, and is available as a scratch register for
unwrapped callee code (and of course the return value).
Wrapped function pointers are themselves wrapped in a struct
paravirt_callee_save structure, in order to get some warning from the
compiler when functions with mismatched calling conventions are used.
The most common paravirt ops, both statically and dynamically, are
interrupt enable/disable/save/restore, so handle them first. This is
particularly easy since their calls are handled specially anyway.
XXX Deal with VMI. What's their calling convention?
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: Optimization
Each asm paravirt-ops call says what registers are available for
clobbering. This patch makes use of this to selectively save/restore
registers around each pvops call. In many cases this significantly
shrinks code size.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: Fix latent bug
The clobber is trying to say that anything except RDI is available for
clobbering, but actually clobbers everything. This hasn't mattered
because the clobbers were basically ignored, but subsequent patches
will rely on them.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: Optimization
Several paravirt ops implementations simply return their arguments,
the most obvious being the make_pte/pte_val class of operations on
native.
On 32-bit, the identity function is literally a no-op, as the calling
convention uses the same registers for the first argument and return.
On 64-bit, it can be implemented with a single "mov".
This patch adds special identity functions for 32 and 64 bit argument,
and machinery to recognize them and replace them with either nops or a
mov as appropriate.
At the moment, the only users for the identity functions are the
pagetable entry conversion functions.
The result is a measureable improvement on pagetable-heavy benchmarks
(2-3%, reducing the pvops overhead from 5 to 2%).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: Cleanup
Move remaining mmu-related stuff into mmu.c.
A general cleanup, and lay the groundwork for later patches.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: fix rare crash on 32-bit
The 32-bit APIC drivers had their send_IPI_self vectors set to NULL,
but ioapic_retrigger_irq() depends on it being always set. Fix it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In Linus' current -git the cpumask member is now a pointer.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This kernel symbol provides a way for drivers to switch on alternate
function for a certain GPIO pin. Turning it off is done implicitly when
changing the GPIO direction, as that would be fixed when using the given
pin als alternate function.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the {set,get}_434_reg() prototypes, as the functions have been
removed. Also move the prototypes for {get,set}_latch_u5() to the correct
place.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As rb532_dev3_ctl_res is not used by any platform device, it can be dropped
when not used for holding the physical address of the device 3 controller.
Also a size of one byte should suffice when ioremapping the physical
address mentioned above, as only a single byte is being read from and
written to it.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These kernel symbols are unused. Also, since dev3 init has been moved to
devices.c, set_434_reg() breaks compiling as it uses dev3.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This code doesn't belong to gpio.c, as it's completely unrelated to
GPIO. As dev1 and dev2 init code is in devices.c, it seems to be a more
adequate place.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The data to be written is just a byte, so use writeb instead of writel.
Also, dev3.base contains the address, not the data so referencing here
is wrong.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Jeremy Fitzhardinge
Julia Lawall
paulfax
Anton Vorontsov
Michael Neuling
Jaswinder Singh Rajput
Pavel Emelyanov
Ingo Molnar
David S. Miller
Masami Hiramatsu
Linus Torvalds
Yinghai Lu
Alexey Dobriyan
Tejun Heo
Mark Langsdorf
Kyle McMartin
Hiroshi Shimamoto
Timothy S. Nelson
H. Peter Anvin
Alex Chiang
Borislav Petkov
Kyle McMartin
Michael Hennerich
Mike Frysinger
Bernd Schmidt
Graf Yang
Jie Zhang
Bryan Wu
Grace Pan
Sonic Zhang
Robin Getz
Uwe Kleine-Koenig
Thomas Renninger
Huang Ying
Borislav Petkov
Stephen Rothwell
Martin Hicks
Sascha Hauer
Benjamin Herrenschmidt
Russell King
Dave Jones
James Bottomley
Brian Gerst
Cliff Wickman
Uwe Kleine-König
Andreas Schwab
Manuel Lauss
Phil Sutter