Added a platform driver which uses the SDHCI core.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The MMC core has now been fixed to not send silly frequencies to the
drivers which means we can remove this workaround.
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The code is divided in two parts. There is a virtual 'bus' driver
that handles PCI device and registers three new devices one per card
reader type. The other driver handles SD/MMC part of the reader.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Changes pxamci.c to use the regulator subsystem. Uses the regulator case
CONFIG_REGULATOR is defined and a matching is regulator is provided, or
falls back to pdata->setpower otherwise. A warning is displayed case
both a valid regulator and pdata is set, and the regulator is used.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Some controllers allow a much lower frequency than 400kHz.
Keep the minimum frequency within sensible limits.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Because of granularity issues, sometimes we told the hardware to change
to the voltage we were already at. Rework the logic so this doesn't
happen.
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
A pointer to mmc_omap_probe which lives in .init.text is passed to the
core via platform_driver_register and so the kernel might oops if probe
is called after the init code is discarded.
As requested by David Brownell platform_driver_probe is used instead of
moving the probe function to .devinit.text. This saves some memory, but
might have the downside that a device being registered after the call to
mmc_omap_init but before the init sections are discarded will not be
bound anymore to the driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Speedup for slow cards by transfering more data at once.
This patch also reduces the amount of wear-out of the flash
blocks because fewer partial blocks are written.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
With this patch, mmc_rescan can detect the removal of an mmc card and
the insertion of (possibly another) card in the same run. This means
that a card change can be detected without having to call
mmc_detect_change multiple times.
This change generalises the core such that it can be easily used by
hosts which provide a mechanism to detect only the presence of a card
reader cover, which has to be taken off in order to insert a card. Other
hosts ("card detect" or "MMC_CAP_NEEDS_POLL") each receive an event when
a card is removed and when a card is inserted, so it is sufficient for
them if mmc_rescan handles only one event at a time. "Cover detect"
hosts, however, only receive events about the cover status. This means
that between 2 subsequent events, both a card removal and a card
insertion can occur. In this case, the pre-patch version of mmc_rescan
would only detect the removal of the previous card but not the insertion
of the new card.
Signed-off-by: Jorg Schummer <ext-jorg.2.schummer@nokia.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: Fix oops on unaligned user access
avr32: Add support for Mediama RMTx add-on board for ATNGW100
avr32: Change Atmel ATNGW100 config to add choice of add-on board
Fix MIMC200 board LCD init
avr32: Fix clash in ATMEL_USART_ flags
avr32: remove obsolete hw_interrupt_type
avr32: Solves problem with inverted MCI detect pin on Merisc board
atmel-mci: Add support for inverted detect pin
* 'for-2.6.31' of git://git.kernel.dk/linux-2.6-block: (153 commits)
block: add request clone interface (v2)
floppy: fix hibernation
ramdisk: remove long-deprecated "ramdisk=" boot-time parameter
fs/bio.c: add missing __user annotation
block: prevent possible io_context->refcount overflow
Add serial number support for virtio_blk, V4a
block: Add missing bounce_pfn stacking and fix comments
Revert "block: Fix bounce limit setting in DM"
cciss: decode unit attention in SCSI error handling code
cciss: Remove no longer needed sendcmd reject processing code
cciss: change SCSI error handling routines to work with interrupts enabled.
cciss: separate error processing and command retrying code in sendcmd_withirq_core()
cciss: factor out fix target status processing code from sendcmd functions
cciss: simplify interface of sendcmd() and sendcmd_withirq()
cciss: factor out core of sendcmd_withirq() for use by SCSI error handling code
cciss: Use schedule_timeout_uninterruptible in SCSI error handling code
block: needs to set the residual length of a bidi request
Revert "block: implement blkdev_readpages"
block: Fix bounce limit setting in DM
Removed reference to non-existing file Documentation/PCI/PCI-DMA-mapping.txt
...
Manually fix conflicts with tracing updates in:
block/blk-sysfs.c
drivers/ide/ide-atapi.c
drivers/ide/ide-cd.c
drivers/ide/ide-floppy.c
drivers/ide/ide-tape.c
include/trace/events/block.h
kernel/trace/blktrace.c
I found the PrimeCell/AMBA Bus drivers distrusting the resource
passed in as part of the struct amba_device abstraction. This
patch removes all hard coded resource sizes found in the PrimeCell
drivers and move the responsibility of this definition back to
the platform/board device definition, which already exist and
appear to be correct for all in-tree users of these drivers.
We do this using the resource_size() inline function which was
also replicated in the only driver using the resource size, so
that has been changed too. The KMI_SIZE was left in kmi.h in case
someone likes it. Test-compiled against Versatile and Integrator
defconfigs, seems to work but I don't posess these boards and
cannot test them.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Freescale eSDHC controller has the special order for
the HOST version register. that is not same as the other's
registers. The address of HOSTVER in spec is 0xFE, and
we need use the in_be16(0xFE) to access it, not in_be16(0xFC).
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Especially with Sandisk SDHC cards, the second SWITCH command was failing
with a timeout and the card was not recognized at all. However if the
system was busy, or debugging was enabled, or a udelay(100) was inserted
before the second SWITCH command in the core code, then the timing was
so that the card started to work.
With some unusual block sizes, the data FIFO status doesn't indicate a
"empty" state right away when the data transfer is done. Queuing
another data transfer in that condition results in a transfer timeout.
The empty FIFO bit eventually get set by itself in less than 50 usecs
when it is not set right away. So let's just poll for that bit before
configuring the controller with a new data transfer.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Empirical evidences show that this is causing far more problems than it
solves when this mode is enabled in the host hardware. Amongst those
cards that are known to be non functional when this bit is set are:
A-Data "Speedy" 2GB SD card
Kodak 512MB SD card
Ativa 1GB MicroSD card
Marvell 8688 (WIFI/Bluetooth) SDIO card
Since those cards do work on other host controllers which do honnor the
hs timing, the issue must be with this particular host hardware.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
disable_irq() should wait for all running handlers to complete
before returning. As such, if it's used to disable an interrupt
from that interrupt's handler it will deadlock. This replaces
the dangerous instances with the _nosync() variant which doesn't
have this problem.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
We plan to use fsl,esdhc going forward as the base compatible so update
the driver to bind against it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
When a software timeout occurs in polling mode hardware was left in
an indeterminate state causing subsequent operations to block.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
This is a temporary workaround until the MMC stack can be fixed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Decouple the HSMMC glue from the twl4030 as the only
regulator provider, using the regulator framework instead.
This makes the glue's "mmc-twl4030" name become a complete
misnomer ... this code could probably all migrate into the
HSMMC driver now.
Tested on 3430SDP (SD and low-voltage MMC) and Beagle (SD),
plus some other boards (including Overo) after they were
converted to set up MMC regulators properly.
Eventually all boards should just associate a regulator with
each MMC controller they use. In some cases (Overo MMC2 and
Pandora MMC3, at least) that would be a fixed-voltage regulator
with no real software control. As a temporary hack (pending
regulator-next updates to make the "fixed.c" regulator become
usable) there's a new ocr_mask field for those boards.
Patch updated with a fix for disabling vcc_aux by
Adrian Hunter <adrian.hunter@nokia.com>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Until now we have had a 1:1 mapping between storage device physical
block size and the logical block sized used when addressing the device.
With SATA 4KB drives coming out that will no longer be the case. The
sector size will be 4KB but the logical block size will remain
512-bytes. Hence we need to distinguish between the physical block size
and the logical ditto.
This patch renames hardsect_size to logical_block_size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The second argument of the probe method points to the amba_id
structure, so it's better passed with the correct type. None of the
current in-tree drivers uses the pointer, so they have only been
checked for a clean compile.
Change suggested by Russell King.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move all the gpio functions out of <mach/hardware.h> as
this file is for defining the generic IO base addresses
for the kernel IO calls.
Make a new header <mach/gpio-fns.h> to take this and
include it via the chain from <linux/gpio.h> which is
what most of these files should be using (and will be
changed as soon as possible).
Note, this does make minor changes to some drivers but
should not mess up any pending merges.
CC: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Till now block layer allowed two separate modes of request execution.
A request is always acquired from the request queue via
elv_next_request(). After that, drivers are free to either dequeue it
or process it without dequeueing. Dequeue allows elv_next_request()
to return the next request so that multiple requests can be in flight.
Executing requests without dequeueing has its merits mostly in
allowing drivers for simpler devices which can't do sg to deal with
segments only without considering request boundary. However, the
benefit this brings is dubious and declining while the cost of the API
ambiguity is increasing. Segment based drivers are usually for very
old or limited devices and as converting to dequeueing model isn't
difficult, it doesn't justify the API overhead it puts on block layer
and its more modern users.
Previous patches converted all block low level drivers to dequeueing
model. This patch completes the API transition by...
* renaming elv_next_request() to blk_peek_request()
* renaming blkdev_dequeue_request() to blk_start_request()
* adding blk_fetch_request() which is combination of peek and start
* disallowing completion of queued (not started) requests
* applying new API to all LLDs
Renamings are for consistency and to break out of tree code so that
it's apparent that out of tree drivers need updating.
[ Impact: block request issue API cleanup, no functional change ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: unsik Kim <donari75@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Laurent Vivier <Laurent@lvivier.info>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
plat-omap/mailbox, floppy, viocd, mspro_block, i2o_block and
mmc/card/queue are already pretty close to dequeueing model and can be
converted with simple changes. Convert them.
While at it,
* xen-blkfront: !fs check moved downwards to share dequeue call with
normal path.
* mspro_block: __blk_end_request(..., blk_rq_cur_byte()) converted to
__blk_end_request_cur()
* mmc/card/queue: loop of __blk_end_request() converted to
__blk_end_request_all()
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent cleanups, there is no place where low level driver
directly manipulates request fields. This means that the 'hard'
request fields always equal the !hard fields. Convert all
rq->sectors, nr_sectors and current_nr_sectors references to
accessors.
While at it, drop superflous blk_rq_pos() < 0 test in swim.c.
[ Impact: use pos and nr_sectors accessors ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dario Ballabio <ballabio_dario@emc.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: unsik Kim <donari75@gmail.com>
Cc: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
arch-imx is superseeded by the MXC architecture support.
This patch removes arch-imx from the build system.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mvsdio: fix CONFIG_PM=y build
mmci: fix crash with debug enabled
sdhci: catch ADMA errors
mmc: increase power up delay
sdhci-pci: bad error handling in probe function
mmc_block: be prepared for oversized requests
Fix usage of obsolete parameters and functions in the driver's PM
callbacks.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
If MMC debugging is enabled, the mmci driver oopses because the DBG
macro uses host->mmc before it is set. Set it earlier.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The TI controller on Toshiba Tecra M5 needs more time to power up or
the cards will init incorrectly or not at all.
Signed-off-by: José M. Fernández <josemariafg@gmail.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The goto unmap is too early, we haven't allocated host or done the
request_region().
Found by smatch (http://repo.or.cz/w/smatch.git).
[ Second error path fix by Pierre Ossman ]
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The block layer does not support very low sector count restrictions
so we need to be prepared to handle bigger requests than we can send
directly to the controller.
Problem found by Manuel Lauss.
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
calls
The S3C24XX DMA API channel configuration registers are being passed
values comprised of register values which makes it hard to move the
API to cover both the S3C24XX and S3C64XX.
These values can be calculated from knowing which device the channel
is connected to, so remove them from the two calls s3c2410_dma_config
and s3c2410_dma_devconfig.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Same patch as before, modified to use bool. Also adds description of
the new field in struct atmel_mci that I missed in the first patch.
This patch adds Atmel MCI support for inverted detect pins.
Signed-off-by: Jonas Larsson <jonas.larsson@martinsson.se>
Acked-by: Pierre Ossman <pierre@ossman.eu>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
A very large subset of SD cards in the market send their
responses and data non-byte-aligned. So add logic to the
mmc spi driver to handle this mess.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
With spurious interrupt cmd can be null even when we have CC
set in irq status.
Fixes: NB#106295 - prevent potential kernel crash in the MMC driver
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
This fixes the issue noted by Russell King:
drivers/mmc/host/omap_hsmmc.c: In function 'mmc_omap_xfer_done':
drivers/mmc/host/omap_hsmmc.c:301: error: implicit declaration of function 'mmc_omap_fclk_lazy_disable'
This got broken by 4a694dc915.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
SD/MMC card timeouts can be very high. So avoid busy-waiting,
using the scheduler. Calculate all timeouts in jiffies units,
because this will give us the correct sign when to involve
the scheduler.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Some cards are not able to calculate a valid CRC16 value
for CID and CSD reads (CRC for 512 byte data blocks is OK).
By moving the CRC enable after the read of CID and CSD, these
cards can be used. This patch was tested with a faulty 8 GByte
takeMS Class 6 SDHC card. This patch was suggested by
Pierre Ossman.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Spurious IRQs seen on MMC after 2.6.29. Flush posted write in IRQ
handler.
The interrupt line is released by clearing the error status bits
in the MMCHS_STAT register, which must occur before the interrupt
handler returns to avoid unwanted irqs. Hence the need to flush
the posted write.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Tony Lindgen <tony@atomide.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
DMA request source (RSSR) needs to be set only once (in probe).
DMA burst length (BLR) need to be set only in set_ios()
This cleans up imxmci_setup_data() and should make it a little
bit faster :)
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add __init __exit for appropriate probe and remove functions.
Conver to platform_driver_probe()
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (42 commits)
atmel-mci: fix sdc_reg typo
tmio_mmc: add maintainer
mmc: Add OpenFirmware bindings for SDHCI driver
sdhci: Add quirk for forcing maximum block size to 2048 bytes
sdhci: Add quirk for controllers that need IRQ re-init after reset
sdhci: Add quirk for controllers that need small delays for PIO
sdhci: Add set_clock callback and a quirk for nonstandard clocks
sdhci: Add get_{max,timeout}_clock callbacks
sdhci: Add support for hosts reporting inverted write-protect state
sdhci: Add support for card-detection polling
sdhci: Enable only relevant (DMA/PIO) interrupts during transfers
sdhci: Split card-detection IRQs management from sdhci_init()
sdhci: Add support for bus-specific IO memory accessors
mmc_spi: adjust for delayed data token response
omap_hsmmc: Wait for SDBP
omap_hsmmc: Fix MMC3 dma
omap_hsmmc: Disable SDBP at suspend
omap_hsmmc: Do not prefix slot name
omap_hsmmc: Allow cover switch to cause rescan
omap_hsmmc: Add 8-bit bus width mode support
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6: (32 commits)
regulator: twl4030 VAUX3 supports 3.0V
regulator: Support disabling of unused regulators by machines
regulator: Don't increment use_count for boot_on regulators
twl4030-regulator: expose VPLL2
regulator: refcount fixes
regulator: Don't warn if we failed to get a regulator
regulator: Allow boot_on regulators to be disabled by clients
regulator: Implement list_voltage for WM835x LDOs and DCDCs
twl4030-regulator: list more VAUX4 voltages
regulator: Don't warn on omitted voltage constraints
regulator: Implement list_voltage() for WM8400 DCDCs and LDOs
MMC: regulator utilities
regulator: twl4030 voltage enumeration (v2)
regulator: twl4030 regulators
regulator: get_status() grows kerneldoc
regulator: enumerate voltages (v2)
regulator: Fix get_mode() for WM835x DCDCs
regulator: Allow regulators to set the initial operating mode
regulator: Suggest use of datasheet supply or pin names for consumers
regulator: email - update email address and regulator webpage.
...
Glue between MMC and regulator stacks ... verified with
some OMAP3 boards using adjustable and configured-as-fixed
regulators on several MMC controllers.
These calls are intended to be used by MMC host adapters
using at least one regulator per host. Examples include
slots with regulators supporting multiple voltages and
ones using multiple voltage rails (e.g. DAT4..DAT7 using a
separate supply, or a split rail chip like certain SDIO
WLAN or eMMC solutions).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This fixes a bug when setting the sdc_reg for 4-bit bus width
transactions.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds a new driver: sdhci-of. The driver is similar to
the sdhci-pci, it contains common probe code, and controller-specific
ops and quirks.
So far there are only Freescale eSDHC ops and quirks.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
FSL eSDHC controllers can support maximum block size up to 4096 bytes,
the MBL (Maximum Block Length) field in the capabilities register
extended by one bit, and is set to 0x3.
But the SDHCI core doesn't support blocks of 4096 bytes, and thus
forces blksz to the lowest value -- 512 bytes. With this patch we can
pin up the blksz to the maximum supported block size, i.e. 2048 bytes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
FSL eSDHC controllers losing signal/interrupt enable states after
reset, so we should re-enable them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Small udelay is needed to make eSDHC work in PIO mode. Without
the delay reading causes endless interrupt storm, and writing
corrupts data. The first guess would be that we must wait for
some bit in some register, but I didn't find any reliable bits
that change before and after the delay.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
FSL eSDHC hosts have incompatible register map to manage the SDCLK.
This patch adds set_clock callback so that drivers could overwrite
set_clock behaviour.
Similar patch[1] was posted by Ben Dooks, though in Ben's version the
callback is named change_clock, plus the patch has some unrelated bits
that makes the patch difficult to reuse.
[1] http://lkml.org/lkml/2008/12/2/160
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some controllers do not provide clock information in their capabilities
(in the Samsung case, it is because there are multiple clock sources
available to the controller). Add hooks to allow the system to supply
clock information.
p.s.
In the original Ben's patch there was a bug that makes sdhci_add_host()
return -ENODEV even if callbacks were specified. This is fixed now.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds SDHCI_QUIRK_INVERTED_WRITE_PROTECT quirk. When
specified, the sdhci driver will invert WP state.
p.s. Actually, the quirk is more board-specific than
controller-specific.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds SDHCI_QUIRK_BROKEN_CARD_DETECTION quirk. When specified,
sdhci driver will set MMC_CAP_NEEDS_POLL MMC host capability, and won't
enable card insert/remove interrupts.
This is needed for hosts with unreliable card detection, such as FSL
eSDHC. The original eSDHC driver was tring to "debounce" card-detection
IRQs by reading present state and disabling particular interrupts. But
with this debouncing scheme I noticed that sometimes we miss card
insertion/removal events.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some hosts (that is, FSL eSDHC) throw PIO interrupts during DMA
transfers, this causes tons of unneeded interrupts, and thus highly
degraded speed.
This patch modifies the driver so that now we only enable relevant
(DMA or PIO) interrupts during transfers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Card detection interrupts should be handled separately as they should
not be enabled before mmc_add_host() returns and should be disabled
before calling mmc_remove_host(). The same is for suspend and resume
routines.
sdhci_init() no longer enables card-detection irqs. Instead, two new
functions implemented: sdhci_enable_card_detection() and
sdhci_disable_card_detection().
New sdhci_reinit() call implemented to behave the same way as the old
sdhci_init().
Also, this patch implements and uses few new helpers to manage IRQs in
a more conveinient way, that is:
- sdhci_clear_set_irqs()
- sdhci_unmask_irqs()
- sdhci_mask_irqs()
- SDHCI_INT_ALL_MASK constant
sdhci_enable_sdio_irq() converted to these new helpers, plus the
helpers will be used by the subsequent patches.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Currently the SDHCI driver works with PCI accessors (write{l,b,w} and
read{l,b,w}).
With this patch drivers may change memory accessors, so that we can
support hosts with "weird" IO memory access requirments.
For example, in "FSL eSDHC" SDHCI hardware all registers are 32 bit
width, with big-endian addressing. That is, readb(0x2f) should turn
into readb(0x2c), and readw(0x2c) should be translated to
le16_to_cpu(readw(0x2e)).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some cards are not able to send the data token in time, but
miss the time frame for some bits(!). So synchronize to the
start of the token.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
It is necessary to wait for bus power before sending
any commands.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Data transfers on third OMAP3 MMC controller don't work
because DMA line numbers are only defined for MMC1 and MMC2.
Fix that and store line numbers in mmc_omap_host structure
to reduce code size.
Tested on OMAP3 pandora board.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Turn off the bus power at suspend.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Allow slot_name to be the same as the other OMAP
driver, by removing the redundant "slot:" prefix.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Allow a cover switch to be used to cause a rescan of the
MMC slot.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Instead of using the bounce buffer, using scatter-gather emulation
(as in the OMAP1/2 MMC driver) removes the need of one extra memory
copy and improves performance.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some MMC commands result in the card becoming busy after
the response is received. This needs to be specified
for the omap_hsmmc host controller, which is what this
patch does. However, the effect is that some commands
with no data will cause a Transfer Complete (TC) interrupt
in addition to the Command Complete (CC) interrupt.
In order to deal with that, the irq handler has needed
a few changes also.
The benefit of this change is that the omap_hsmmc host
controller driver now waits for the TC interrupt while
the card is busy, so the mmc_block driver needs to poll
the card status just once instead of repeatedly.
i.e. the net result is more sleep and less cpu.
The command sequence for open-ended multi-block write
with DMA is now:
Issue write command CMD25
Receive CC interrupt
Data is sent
Receive TC interrupt (DMA is done)
Issue stop command CMD12
Receive CC interrupt
Card is busy
Receive TC interrupt
Card is now ready for next transfer
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This supports MMC/SD/SDIO currently found on the Kirkwood 88F6281 and
88F6192 SoC controllers.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
drivers/mmc/host/tmio_mmc.h: In function 'tmio_mmc_kmap_atomic':
drivers/mmc/host/tmio_mmc.h:147: error: implicit declaration of function 'kmap_atomic'
drivers/mmc/host/tmio_mmc.h:147: error: 'KM_BIO_SRC_IRQ' undeclared (first use in this function)
drivers/mmc/host/tmio_mmc.h: In function 'tmio_mmc_kunmap_atomic':
drivers/mmc/host/tmio_mmc.h:153: error: implicit declaration of function 'kunmap_atomic'
drivers/mmc/host/tmio_mmc.h:153: error: 'KM_BIO_SRC_IRQ' undeclared (first use in this function)
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Update the tmio_mmc code to call mmc_free_host() when
done using the private data. Without this fix the driver
frees memory and then keeps on using it as private data.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Update the tmio_mmc code to use resource_size(). With this
patch applied the correct resource size is passed to ioremap().
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some SD cards have very high timeouts in SPI mode.
So adjust the timeouts from theory to practice.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some cards are slower than the standard allows and need more
time to respond to a command. Max. observed number of bytes
was 12.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Allow the platform data structures to specify spi mode 3
(if there is a pullup on the clock line or the spi hardware
is not able to serve spi mode 0).
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
During mmc unsafe resume, choose the right voltage for the card after
powerup.
Although this has not seen to cause trouble, it's the wrong behaviour.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Most registers lose its state when the processor wakes up from sleep state.
Thus registers should be initialized, when the processor wakes up. However the
current hsmmc 'resume' function doesn't consider this issue and finally makes
deadlock. So this patch fixes this problem.
Signed-off-by: Kim Kyuwon <chammoru@gmail.com>
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Remove code that turns MMC1 power back on after it
has been powered off (when the voltage is 1.8V).
The offending code is not necessary because the
host controller bus voltage is initialized to
3V when probing or resuming. Note that MMC powers up
with the highest voltage available (see mmc_power_up())
which will be 3V also.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Extended CSD is a MMC card register. As increasingly interesting
fields are being added to Extended CSD, it is helpful to see its
value. Note that SD cards do not have an Extended CSD
register, so it is MMC only.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Currently we are using an explicit udev rule to trigger loading of the
mmc-block module when an MMC or SD card is detected:
SUBSYSTEM=="mmc", RUN+="/sbin/modprobe -Qba mmc-block"
It makes much more sense for the mmc bus driver and the mmc-block module to
share MODALIAS information so that they are linked automatically.
There is no real information of use in the MMC system at the current time.
All devices inserted require us to load the mmc-block device. Until such
time as useful parameters exist simply reflect the module linkage via
the module alias below:
mmc:block
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The delayed work item mmc_host.detect is now cancelled before flushing
the work queue. This takes care of cases when delayed_work was scheduled
for mmc_host.detect, but not yet placed in the work queue.
Signed-off-by: Jorg Schummer <ext-jorg.2.schummer@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The s3cmci driver is calling s3c2410_dma_config with incorrect data for
the DCON register. The S3C2410_DCON_HWTRIG is implicit in the channel
configuration and the device selection of S3C2410_DCON_CH0_SDI is
incorrect as the DMA system may not select channel 0.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds __devinit and __devexit macros to the module probe and
remove functions in MMCI. Now includes the __devexit_p() thing too.
Signed-off-by: Linus Walleij <linus.walleij@ericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. Driver code where pxa_request_dma() is called will most likely
reference DMA registers as well, and it is really unnecessary
to include pxa-regs.h just for this. Move the definitions into
<mach/dma.h> and make relevant drivers include it instead of
<mach/pxa-regs.h>.
2. Introduce DMAC_REGS_VIRT as the virtual address base for these
DMA registers. This allows later processors to re-use the same
IP while registers may start at different I/O address.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Commit 0d3e0460f3
"MMC: CSD and CID timeout values" inadvertently broke
the timeout for the MMC command SEND_EXT_CSD.
This patch puts it back again.
Depending on the characteristics of the controller,
this bug may prevent the use of MMC cards.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
As described here: http://lkml.org/lkml/2009/2/20/265
The CAFE chip is broken due to commit e809517f6f.
Anton added a quirk here: http://lkml.org/lkml/2009/2/20/279 that fixes
CAFE's problem. This adds the quirk for CAFE.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The Samsung SDHCI (and FSL eSDHC) controller block seems to fail
to generate an INT_DATA_END after the transfer has completed and
the bus busy state finished.
Changes in e809517f6f to use the
new busy method are the cause of the behaviour change.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
omap_hsmmc: Change while(); loops with finite version
omap_hsmmc: recover from transfer failures
omap_hsmmc: only MMC1 allows HCTL.SDVS != 1.8V
omap_hsmmc: card detect irq bugfix
sdhci: fix led naming
mmc_test: fix basic read test
s3cmci: Fix hangup in do_pio_write()
Revert "sdhci: force high speed capability on some controllers"
MMC: fix bug - SDHC card capacity not correct
The conversion of atmel-mci to dma_request_channel missed the
initialization of the channel dma_slave information. The filter_fn passed
to dma_request_channel is responsible for initializing the channel's
private data. This implementation has the additional benefit of enabling
a generic client-channel data passing mechanism.
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace the infinite 'while() ;' loops
with a finite loop version.
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Timeouts during a command that has a data phase can result in the next
command issued after the command that failed not being processed, i.e. no
interrupt ever occurs to indicate the command has completed. This failure
can result in a deadlock.
This patch resets the data state machine to clear the error in case of a
command timeout.
Tested on OMAP3430 chip and intensive MMC/SD device removal while
transferring data.
Signed-off-by: Andy Lowe <alowe@mvista.com>
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Based on a patch from Tony Lindgren ... after initialization,
never change HCTL.SDVS except for MMC1. The other controller
instances only support 1.8V in that field, although they can
suport other card/SDIO/eMMC/... voltages with level shifting
solutions such as external transceivers.
MMC2 behavior sanity tested on Overo/WLAN, OMAP3430 SDP, and
custom hardware. MMC1 also sanity tested on those platforms
plus Beagle. This also fixes a bug preventing MMC2 (and also
presumably MMC3) from powering down when requested.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Work around lockdep issue when card detect IRQ handlers run in
thread context ... it forces IRQF_DISABLED, which prevents all
access to twl4030 card detect signals.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fix the led device naming for the sdhci driver.
The led class documentation defines the led name to have the
form "devicename:colour:function" while not applicable sections
should be left blank.
To comply with the documentation the led device name is changed
from "mmc*" to "mmc*::".
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Due to a typo in the Basic Read test, it's currently identical to the
Basic Write test. Fix this.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This commit fixes the regression what was added by commit
088a78af97 "s3cmci: Support transfers
which are not multiple of 32 bits."
fifo_free() now returns amount of available space in FIFO buffer in
bytes. But do_pio_write() writes to FIFO 32-bit words. Condition for
return from cycle is (fifo_free() == 0), but when fifo has 1..3 bytes
of free space then this condition will never be true and system hangs.
This patch changes condition in the while() to (fifo_free() > 3).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This reverts commit a4b7619377.
It turned out that the controller had problem running at the
higher speed, so go back to trusting the hardware capability
bits.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Convert OMAP MMC driver to match clocks using the device ID and a
connection ID rather than a clock name. This allows us to eliminate
the OMAP1/OMAP2 differences for the function clock.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With the PXA270 MMC hardware, there seems to be an issue of
data corruption on writes where a 4KB data block is offset
by one byte.
If we delay enabling the DMA for writes until after the CMD/RESP
has finished, the problem seems to be fixed.
related to PXA270 Erratum #91
Tested-by: Vernon Sauder <VernonInHand@gmail.com>
Signed-off-by: Cliff Brake <cbrake@bec-systems.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
If ricoh_mmc suspends before sdhci_pci, it will pull the card
out from under the controller, which could leave the system in
a very confused state.
Using suspend_late/resume_early ensures that sdhci_pci suspends first
and resumes second.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds support for the ST Microelectronics version of
the PL180 PrimeCell. They use designer ID 0x80 and have a few
alterations/bugfixes related to open drain and HW flow control.
They also add some SDIO registers, I am unsure if these are
in ST HW only or if this is things also added in later ARM
revisions, but they are included in the mmci.h file for
completeness.
Signed-off-by: Linus Walleij <linus.walleij@ericsson.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds a MX2/MX3 specific SDHC driver. The hardware is basically
the same as in the MX1, but unlike the MX1 controller the MX2
controller just works as expected. Since the MX1 driver has more
workarounds for bugs than anything else I had no success with supporting
MX1 and MX2 in a sane way in one driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add omap hsmmc controller for 2430 and 34xx.
Note that this controller has different registers compared to
the earlier omap MMC controller, so sharing code currently is
not possible.
Various updates and fixes from linux-omap list have been
merged into this patch.
Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since dma.h has been moved to arch/arm/mach-s3c2410/include/mach,
use the new include path.
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (22 commits)
ioat: fix self test for multi-channel case
dmaengine: bump initcall level to arch_initcall
dmaengine: advertise all channels on a device to dma_filter_fn
dmaengine: use idr for registering dma device numbers
dmaengine: add a release for dma class devices and dependent infrastructure
ioat: do not perform removal actions at shutdown
iop-adma: enable module removal
iop-adma: kill debug BUG_ON
iop-adma: let devm do its job, don't duplicate free
dmaengine: kill enum dma_state_client
dmaengine: remove 'bigref' infrastructure
dmaengine: kill struct dma_client and supporting infrastructure
dmaengine: replace dma_async_client_register with dmaengine_get
atmel-mci: convert to dma_request_channel and down-level dma_slave
dmatest: convert to dma_request_channel
dmaengine: introduce dma_request_channel and private channels
net_dma: convert to dma_find_channel
dmaengine: provide a common 'issue_pending_all' implementation
dmaengine: centralize channel allocation, introduce dma_find_channel
dmaengine: up-level reference counting to the module level
...
DMA_NAK is now useless. We can just use a bool instead.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
All users have been converted to either the general-purpose allocator,
dma_find_channel, or dma_request_channel.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
dma_request_channel provides an exclusive channel, so we no longer need to
pass slave data through dmaengine.
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Simply, if a client wants any dmaengine channel then prevent all dmaengine
modules from being removed. Once the clients are done re-enable module
removal.
Why?, beyond reducing complication:
1/ Tracking reference counts per-transaction in an efficient manner, as
is currently done, requires a complicated scheme to avoid cache-line
bouncing effects.
2/ Per-transaction ref-counting gives the false impression that a
dma-driver can be gracefully removed ahead of its user (net, md, or
dma-slave)
3/ None of the in-tree dma-drivers talk to hot pluggable hardware, but
if such an engine were built one day we still would not need to notify
clients of remove events. The driver can simply return NULL to a
->prep() request, something that is much easier for a client to handle.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Needed to use the atmel-mci driver in an architecture
independant maner.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Get rid of a silent failure mode when the MMC/SD host doesn't
support the voltages needed to operate a given card, by
adding a warning. A 3.3V host and a 3.0V card, for example,
no longer need to mysteriously just not work at all.
This isn't the best diagnostic; ideally it would also tell
what voltage the card and host support (and not just by
dumping the bitmasks).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The support is implemented via platform data accessors, new module
(of_mmc_spi) will be created automatically when the driver compiles
on OpenFirmware platforms. Link-time dependency will load the module
automatically.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
dma_unmap_sg should be given the same length as dma_map_sg, not the
value returned from dma_map_sg
Signed-off-by: Vernon Sauder <vsauder@inhand.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
If a card encounters an ECC error while reading a sector it will
timeout. Instead of reporting the entire I/O request as having
an error, redo the I/O one sector at a time so that all readable
sectors are provided to the upper layers.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
In each case, if the NULL test is necessary, then the dereference should be
moved below the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
As reported by Randy Dunlap, having sdhci built-in and LEDs class
as a module resulted in undefined symbols. Change the code to handle
that case properly (by not having LEDs class support in sdhci).
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add command response and card status to error
messages.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This function sets the OCR mask bits according to provided voltage
ranges. Will be used by the mmc_spi OpenFirmware bindings.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The latest generation of laptops are shipping with a newer
model of Ricoh chip where the firewire controller is the
primary PCI function but a cardbus controller is also present.
The existing code assumes that if a cardbus controller is,
present, then it must be the one to manipulate - but the real
rule is that you manipulate PCI function 0. This patch adds an
additional constraint that the target must be function 0.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
CONFIG_LEDS_CLASS is defined only if led-class is built-in, otherwise
when it is a module the option is called CONFIG_LEDS_CLASS_MODULE. Led
support should also be activated in this case.
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
sg_init_one is reading a be32, annotate as such.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Use the new pci_ioremap_bar() function in drivers/mmc.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Use readl/writel instead of direct pointer deref.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This removes clkrt and cmdat from struct imxmci_host, they are
unused.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This cleans up the warnings issued by the checkpatch script
and remove the file history from the header
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add low-level initialization for hsmmc controller. Merged into
this patch patch are various improvments and board support by
Grazvydas Ignotas and David Brownell.
Also change wire4 to be wires, as some newer controllers support
8 data lines.
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This will simplify the MMC low-level init, and make it more
flexible to add support for a newer MMC controller in the
following patches.
The patch rearranges platform data and gets rid of slot vs
controller confusion in the old data structures. Also fix
device id numbering in the clock code.
Some code snippets are based on an earlier patch by
Russell King <linux@arm.linux.org.uk>.
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some Ricoh SD card readers seems to advertise themselves slightly differently.
This patches the driver to will recognise an additional product id, and it
appears to work perfectly.
% pccardctl info
PRODID_1="RICOH"
PRODID_2="Bay Controller"
PRODID_3=""
PRODID_4=""
MANFID=0000,0000
Signed-off-by: Charles Lowe <aquasync@gmail.com>
Acked-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
As said in function comment mmc_add_host() requires that:
"The host must be prepared to start servicing requests
before this function completes."
During this function, at91_mci_request() can be invoqued
without timer beeing setup leading to a kernel Oops.
This has been reported inserting this driver as a module.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: Wu Xuan <wux@landicorp.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Where devices only have one consumer, passing a consumer clock ID
has no real benefit, and it only encourages wrong implementations of
the clk API. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When ISA_DMA_API is unset, we're not implementing the ISA DMA API,
so there's no point in publishing the prototypes via asm/dma.h, nor
including the machine dependent parts of that API.
This allows us to remove a lot of mach/dma.h files which don't contain
any useful code. Unfortunately though, some platforms put their own
private non-ISA definitions into mach/dma.h, so we leave these behind
and fix the appropriate #include statments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avoid unnecessarily pollution of the kernel's namespace by avoiding
mach/hardware.h. Include this header file where necessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Where devices only have one consumer, passing a consumer clock ID
has no real benefit. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It seems that some cards are slightly out of spec and occasionally
will not be able to complete a write in the alloted 250 ms [1].
Incease the timeout slightly to allow even these cards to function
properly.
[1] http://lkml.org/lkml/2008/9/23/390
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Move mci.h to new position in arch/arm/plat-s3c24xx/include/plat
ready to clean out old include directories.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix fastpath issues
Since mmci_request() can be called from a non-interrupt
context, and does, during kernel init, causing a host
of debug messages during boot if you enable spinlock debugging,
we need to use the spinlock calls that save IRQ flags and
restore them.
Signed-off-by: Linus Walleij <triad@df.lth.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To keep the size of changesets sane we split the switch by drivers;
to keep the damn thing bisectable we do the following:
1) rename the affected methods, add ones with correct
prototypes, make (few) callers handle both. That's this changeset.
2) for each driver convert to new methods. *ALL* drivers
are converted in this series.
3) kill the old (renamed) methods.
Note that it _is_ a flagday; all in-tree drivers are converted and by the
end of this series no trace of old methods remain. The only reason why
we do that this way is to keep the damn thing bisectable and allow per-driver
debugging if anything goes wrong.
New methods:
open(bdev, mode)
release(disk, mode)
ioctl(bdev, mode, cmd, arg) /* Called without BKL */
compat_ioctl(bdev, mode, cmd, arg)
locked_ioctl(bdev, mode, cmd, arg) /* Called with BKL, legacy */
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
s3cmci: Add Ben Dooks/Simtec Electronics to header & copyright
s3cmci: fix continual accesses to host->pio_ptr
s3cmci: Support transfers which are not multiple of 32 bits.
s3cmci: cpufreq support
s3cmci: Make general protocol errors less noisy
mmc_block: tell block layer there is no seek penalty
Since the original authour (Thomas Kleffel) has been too busy to
merge the s3cmci driver and keep it up to date, I (mostly as part
of my role with Simtec Electronics) got the driver to a mergable
state and have been maintaining it since I think that I should
be added to the header. Also add a copyright statement for the
new work.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The s3cmci driver uses the host->pio_ptr field to
point to the current position into the buffer for data
transfer. During the transfers it does the following:
while (fifo_words--)
*(host->pio_ptr++) = readl(from_ptr);
This is inefficent, as host->pio_ptr is not used in any
other part of the transfer but the compiler emits code
which does the following:
while (fifo_words--) {
u32 *ptr = host->pio_ptr;
*ptr = readl(from_ptr);
ptr++;
host->pio_ptr = ptr;
}
This is obviously a waste of a load and store each time
around the loop, which could be up to 16 times depending
on how much needs to be transfered.
Move the ptr accesses to outside the while loop so that
we do not end up reloading/re-writing the pointer.
Note, this seems to make the code 16 bytes larger.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
To be able to do SDIO the s3cmci driver has to support non-word-sized
transfers. Change pio_words into pio_bytes and fix up all the places
where it is used.
This variant of the patch will not overrun the buffer when reading an
odd number of bytes. When writing, this variant will still read past
the end of the buffer, but since the driver can't support non-word-
aligned transfers anyway, this should not be a problem, since a
word-aligned transfer will never cross a page boundary.
This has been tested with a CSR SDIO Bluetooth Type A device on a
Samsung S3C24A0 processor.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
General errors, such as timeouts during probe do not need to
be sent to the console, so move them down to be included if the
debug is enabled.
Such errors include:
s3c2440-sdi s3c2440-sdi: s3cmci_request: no medium present
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (24 commits)
MMC: Use timeout values from CSR
MMC: CSD and CID timeout values
sdhci: 'scratch' may be used uninitialized
mmc: explicitly mention SDIO support in Kconfig
mmc: remove redundant "depends on"
Fix comment in include/linux/mmc/host.h
sdio: high-speed support
mmc_block: hard code 512 byte block size
sdhci: force high speed capability on some controllers
mmc_block: filter out PC requests
mmc_block: indicate strict ordering
mmc_block: inform block layer about sector count restriction
sdio: give sdio irq thread a host specific name
sdio: make sleep on error interruptable
sdhci: reduce card detection delay
sdhci: let the controller wait for busy state to end
atmel-mci: Add missing flush_dcache_page() in PIO transfer code
atmel-mci: Don't overwrite error bits when NOTBUSY is set
atmel-mci: Add experimental DMA support
atmel-mci: support multiple mmc slots
...
Hard-coded timeout values of 250ms for writes and 100ms for reads are
currently used for MMC transactions over SPI. The spec states that the
timeout values from the card should be used.
Signed-off-by: Matthew Fleming <matthew.fleming@imgtec.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The MMC spec states that the timeout for accessing the CSD and CID
registers is 64 clock cycles.
Signed-off-by: Matthew Fleming <matthew.fleming@imgtec.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The variable 'scratch' is always initialized before it's used. The
conditional which is responsible for initialization of 'scratch' will
always evaluate 'true' when the first loop iteration occurs, and thus,
it's properly initialized. GCC doesn't see this, of course, so using
the uninitialized_var() macro seems to work for silencing this case.
Signed-off-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Richard Röjfors
Pierre Ossman
Michał Mirosław
Daniel Ribeiro
Sascha Hauer
Uwe Kleine-König
Wolfgang Muees
Jorg Schummer
Linus Torvalds
Haavard Skinnemoen
Linus Walleij
Russell King
Dave Liu
Nicolas Pitre
Ben Nizette
Kumar Gala
Martin Fuzzey
Anand Gadiyar
David Brownell
Martin K. Petersen
Jens Axboe
Ben Dooks
Alessandro Rubini
Tejun Heo
Rabin Vincent
José M. Fernández
Dan Carpenter
Ben Dooks
Ladislav Michl
Jonas Larsson
Jarkko Lavinen
Tony Lindgren
Kevin Hilman
Paulius Zaleckas
Yang Hongyang
Alexey Dobriyan
Matt LaPlante
Kay Sievers
Hans-Christian Egtvedt
Anton Vorontsov
Adrian Hunter
Grazvydas Ignotas
Juha Yrjola
Maen Suleiman
Alexander Beregalov
Magnus Damm
Balaji Rao
Pierre Ossman
Kim Kyuwon
Adrian Hunter
Andy Whitcroft
Linus Walleij
Eric Miao
Andres Salomon
Dan Williams
Jean Pihet
Helmut Schaa
Yauhen Kharuzhy
Yi Li
Cliff Brake
philipl@overt.org
Linus Walleij
Madhusudhan Chikkature
Ramax Lo
Nicolas Ferre
Vernon Sauder
Julia Lawall
Roel Kluin
Éric Piel
Harvey Harrison
Arjan van de Ven
Marc Kleine-Budde
Sascha Sommer
Al Viro
ben@fluff.org.uk
Christer Weinigel
David Woodhouse
Matthew Fleming
Steven Noonan