Граф коммитов

399833 Коммитов

Автор SHA1 Сообщение Дата
Aida Mynzhasova e58f6f4fb4 powerpc/83xx: gianfar_ptp: select 1588 clock source through dts file
Currently IEEE 1588 timer reference clock source is determined through
hard-coded value in gianfar_ptp driver. This patch allows to select ptp
clock source by means of device tree file node.

For instance:

	fsl,cksel = <0>;

for using external (TSEC_TMR_CLK input) high precision timer
reference clock.

Other acceptable values:

	<1> : eTSEC system clock
	<2> : eTSEC1 transmit clock
	<3> : RTC clock input

When this attribute isn't used, eTSEC system clock will serve as
IEEE 1588 timer reference clock.

Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-30 21:17:16 -07:00
David S. Miller 3f3f0960af Revert "powerpc/83xx: gianfar_ptp: select 1588 clock source through dts file"
This reverts commit 894116bd0e.

I applied the wrong version of this patch, correct
version coming up.

Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-30 21:16:17 -07:00
Neil Horman 5a0068deb6 bonding: Fix broken promiscuity reference counting issue
Recently grabbed this report:
https://bugzilla.redhat.com/show_bug.cgi?id=1005567

Of an issue in which the bonding driver, with an attached vlan encountered the
following errors when bond0 was taken down and back up:

dummy1: promiscuity touches roof, set promiscuity failed. promiscuity feature of
device might be broken.

The error occurs because, during __bond_release_one, if we release our last
slave, we take on a random mac address and issue a NETDEV_CHANGEADDR
notification.  With an attached vlan, the vlan may see that the vlan and bond
mac address were in sync, but no longer are.  This triggers a call to dev_uc_add
and dev_set_rx_mode, which enables IFF_PROMISC on the bond device.  Then, when
we complete __bond_release_one, we use the current state of the bond flags to
determine if we should decrement the promiscuity of the releasing slave.  But
since the bond changed promiscuity state during the release operation, we
incorrectly decrement the slave promisc count when it wasn't in promiscuous mode
to begin with, causing the above error

Fix is pretty simple, just cache the bonding flags at the start of the function
and use those when determining the need to set promiscuity.

This is also needed for the ALLMULTI flag

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Mark Wu <wudxw@linux.vnet.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
Reported-by: Mark Wu <wudxw@linux.vnet.ibm.com>

Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-30 21:10:55 -07:00
Eric Dumazet c9eeec26e3 tcp: TSQ can use a dynamic limit
When TCP Small Queues was added, we used a sysctl to limit amount of
packets queues on Qdisc/device queues for a given TCP flow.

Problem is this limit is either too big for low rates, or too small
for high rates.

Now TCP stack has rate estimation in sk->sk_pacing_rate, and TSO
auto sizing, it can better control number of packets in Qdisc/device
queues.

New limit is two packets or at least 1 to 2 ms worth of packets.

Low rates flows benefit from this patch by having even smaller
number of packets in queues, allowing for faster recovery,
better RTT estimations.

High rates flows benefit from this patch by allowing more than 2 packets
in flight as we had reports this was a limiting factor to reach line
rate. [ In particular if TX completion is delayed because of coalescing
parameters ]

Example for a single flow on 10Gbp link controlled by FQ/pacing

14 packets in flight instead of 2

$ tc -s -d qd
qdisc fq 8001: dev eth0 root refcnt 32 limit 10000p flow_limit 100p
buckets 1024 quantum 3028 initial_quantum 15140
 Sent 1168459366606 bytes 771822841 pkt (dropped 0, overlimits 0
requeues 6822476)
 rate 9346Mbit 771713pps backlog 953820b 14p requeues 6822476
  2047 flow, 2046 inactive, 1 throttled, delay 15673 ns
  2372 gc, 0 highprio, 0 retrans, 9739249 throttled, 0 flows_plimit

Note that sk_pacing_rate is currently set to twice the actual rate, but
this might be refined in the future when a flow is in congestion
avoidance.

Additional change : skb->destructor should be set to tcp_wfree().

A future patch (for linux 3.13+) might remove tcp_limit_output_bytes

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-30 20:41:57 -07:00
Peter Korsgaard bf0ea63807 dm9601: fix IFF_ALLMULTI handling
Pass-all-multicast is controlled by bit 3 in RX control, not bit 2
(pass undersized frames).

Reported-by: Joseph Chang <joseph_chang@davicom.com.tw>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-30 19:48:59 -04:00
Eric Dumazet 8d34ce10c5 pkt_sched: fq: qdisc dismantle fixes
fq_reset() should drops all packets in queue, including
throttled flows.

This patch moves code from fq_destroy() to fq_reset()
to do the cleaning.

fq_change() must stop calling fq_dequeue() if all remaining
packets are from throttled flows.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-30 15:51:23 -04:00
Eric Dumazet b86783587b net: flow_dissector: fix thoff for IPPROTO_AH
In commit 8ed781668d ("flow_keys: include thoff into flow_keys for
later usage"), we missed that existing code was using nhoff as a
temporary variable that could not always contain transport header
offset.

This is not a problem for TCP/UDP because port offset (@poff)
is 0 for these protocols.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-30 15:32:05 -04:00
Wei Liu 8386040b76 MAINTAINERS: add myself as maintainer of xen-netback
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-30 15:16:02 -04:00
Paul Durrant ea732dff5c xen-netback: Handle backend state transitions in a more robust way
When the frontend state changes netback now specifies its desired state to
a new function, set_backend_state(), which transitions through any
necessary intermediate states.
This fixes an issue observed with some old Windows frontend drivers where
they failed to transition through the Closing state and netback would not
behave correctly.

Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-30 15:13:28 -04:00
Paul Marks c9d55d5bff ipv6: Fix preferred_lft not updating in some cases
Consider the scenario where an IPv6 router is advertising a fixed
preferred_lft of 1800 seconds, while the valid_lft begins at 3600
seconds and counts down in realtime.

A client should reset its preferred_lft to 1800 every time the RA is
received, but a bug is causing Linux to ignore the update.

The core problem is here:
  if (prefered_lft != ifp->prefered_lft) {

Note that ifp->prefered_lft is an offset, so it doesn't decrease over
time.  Thus, the comparison is always (1800 != 1800), which fails to
trigger an update.

The most direct solution would be to compute a "stored_prefered_lft",
and use that value in the comparison.  But I think that trying to filter
out unnecessary updates here is a premature optimization.  In order for
the filter to apply, both of these would need to hold:

  - The advertised valid_lft and preferred_lft are both declining in
    real time.
  - No clock skew exists between the router & client.

So in this patch, I've set "update_lft = 1" unconditionally, which
allows the surrounding code to be greatly simplified.

Signed-off-by: Paul Marks <pmarks@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-30 15:06:19 -04:00
Pravin B Shelar d4a71b155c ip_tunnel: Do not use stale inner_iph pointer.
While sending packet skb_cow_head() can change skb header which
invalidates inner_iph pointer to skb header. Following patch
avoid using it. Found by code inspection.

This bug was introduced by commit 0e6fbc5b6c (ip_tunnels: extend
iptunnel_xmit()).

Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-30 15:05:07 -04:00
Aleksander Morgado 2d77f34334 net: qmi_wwan: fix Cinterion PLXX product ID
Cinterion PLXX LTE devices have a 0x0060 product ID, not 0x12d1.

The blacklisting in the serial/option driver does actually use the correct PID,
as per commit 8ff10bdb14 ('USB: Blacklisted
Cinterion's PLxx WWAN Interface').

CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
Signed-off-by: Aleksander Morgado <aleksander@lanedo.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Christian Schmiedl <christian.schmiedl@gemalto.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-30 15:04:07 -04:00
Aida Mynzhasova 894116bd0e powerpc/83xx: gianfar_ptp: select 1588 clock source through dts file
Currently IEEE 1588 timer reference clock source is determined through
hard-coded value in gianfar_ptp driver. This patch allows to select ptp
clock source by means of device tree file node.

For instance:

	fsl,cksel = <0>;

for using external (TSEC_TMR_CLK input) high precision timer
reference clock.

Other acceptable values:

	<1> : eTSEC system clock
	<2> : eTSEC1 transmit clock
	<3> : RTC clock input

When this attribute isn't used, eTSEC system clock will serve as
IEEE 1588 timer reference clock.

Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-30 14:49:47 -04:00
Pravin B Shelar 559835ea72 vxlan: Use RCU apis to access sk_user_data.
Use of RCU api makes vxlan code easier to understand.  It also
fixes bug due to missing ACCESS_ONCE() on sk_user_data dereference.
In rare case without ACCESS_ONCE() compiler might omit vs on
sk_user_data dereference.
Compiler can use vs as alias for sk->sk_user_data, resulting in
multiple sk_user_data dereference in rcu read context which
could change.

CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-30 14:22:59 -04:00
Eric Dumazet 9a3bab6b05 net: net_secret should not depend on TCP
A host might need net_secret[] and never open a single socket.

Problem added in commit aebda156a5
("net: defer net_secret[] initialization")

Based on prior patch from Hannes Frederic Sowa.

Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@strressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-28 15:19:40 -07:00
Eric W. Biederman 50624c934d net: Delay default_device_exit_batch until no devices are unregistering v2
There is currently serialization network namespaces exiting and
network devices exiting as the final part of netdev_run_todo does not
happen under the rtnl_lock.  This is compounded by the fact that the
only list of devices unregistering in netdev_run_todo is local to the
netdev_run_todo.

This lack of serialization in extreme cases results in network devices
unregistering in netdev_run_todo after the loopback device of their
network namespace has been freed (making dst_ifdown unsafe), and after
the their network namespace has exited (making the NETDEV_UNREGISTER,
and NETDEV_UNREGISTER_FINAL callbacks unsafe).

Add the missing serialization by a per network namespace count of how
many network devices are unregistering and having a wait queue that is
woken up whenever the count is decreased.  The count and wait queue
allow default_device_exit_batch to wait until all of the unregistration
activity for a network namespace has finished before proceeding to
unregister the loopback device and then allowing the network namespace
to exit.

Only a single global wait queue is used because there is a single global
lock, and there is a single waiter, per network namespace wait queues
would be a waste of resources.

The per network namespace count of unregistering devices gives a
progress guarantee because the number of network devices unregistering
in an exiting network namespace must ultimately drop to zero (assuming
network device unregistration completes).

The basic logic remains the same as in v1.  This patch is now half
comment and half rtnl_lock_unregistering an expanded version of
wait_event performs no extra work in the common case where no network
devices are unregistering when we get to default_device_exit_batch.

Reported-by: Francesco Ruggeri <fruggeri@aristanetworks.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-28 15:09:15 -07:00
Catalin\(ux\) M. BOIE 7df37ff33d IPv6 NAT: Do not drop DNATed 6to4/6rd packets
When a router is doing DNAT for 6to4/6rd packets the latest
anti-spoofing commit 218774dc ("ipv6: add anti-spoofing checks for
6to4 and 6rd") will drop them because the IPv6 address embedded does
not match the IPv4 destination. This patch will allow them to pass by
testing if we have an address that matches on 6to4/6rd interface.  I
have been hit by this problem using Fedora and IPV6TO4_IPV4ADDR.
Also, log the dropped packets (with rate limit).

Signed-off-by: Catalin(ux) M. BOIE <catab@embedromix.ro>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-28 15:56:15 -04:00
Ming Lei 60e453a940 USBNET: fix handling padding packet
Commit 638c5115a7949(USBNET: support DMA SG) introduces DMA SG
if the usb host controller is capable of building packet from
discontinuous buffers, but missed handling padding packet when
building DMA SG.

This patch attachs the pre-allocated padding packet at the
end of the sg list, so padding packet can be sent to device
if drivers require that.

Reported-by: David Laight <David.Laight@aculab.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-28 15:42:49 -04:00
Sucheta Chakraborty 6645161513 qlcnic: Fix register device in FAILED state for 82xx.
o Commit 7e2cf4feba
  ("qlcnic: change driver hardware interface mechanism")
  has overwritten
  commit b43e5ee76a
  ("qlcnic: Register device in FAILED state")

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-27 17:26:20 -04:00
Ajit Khaparde a60b3a13ab be2net: Fix to display the VLAN priority for a VF
VLAN priority is not being displayed for a VF currently when user executes
"ip link show" command. This patch fixes it.

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-27 17:11:49 -04:00
Ajit Khaparde b9fc0e53b0 be2net: Fix to configure VLAN priority for a VF interface.
Thix fix allows the VLAN priority to be configured for a VF interface
via the "ip link set DEVICE vf NUM" path.

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-27 17:11:49 -04:00
Ajit Khaparde 45c459739e be2net: Fix to allow VLAN configuration on VF interfaces.
Now the VF interfaces have privilege to add VLANs.
Allow VLANs to be configured on these interfaces.

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-27 17:11:49 -04:00
Ajit Khaparde 1aa9673c20 be2net: Fix number of VLANs supported in UMC mode for BE3-R.
In BE3-R, when UMC is enabled, the number of VLANs that can be added
to the interface is reduced to 15.

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-27 17:11:49 -04:00
Ajit Khaparde d9d604f865 be2net: Fix VLAN promiscuous mode programming
When the interface runs out of the allocated entries in VLAN table,
we program the interface in VLAN promiscuous mode.
Use OPCODE_COMMON_NTWK_RX_FILTER to set VLAN Promiscuous mode
instead of OPCODE_COMMON_NTWK_VLAN_CONFIG.

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-27 17:11:49 -04:00
Ajit Khaparde d44517fde6 be2net: Fix the size of be_nic_res_desc structure
Size of be_nic_res_desc structure is incorrect. Fix it.

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-27 17:11:49 -04:00
Ajit Khaparde b54881f994 be2net: Fix to prevent Tx stall on SH-R when packet size < 32
Tx on SH-R can lockup if the packet size is less than 32 bytes.
Pad such packets to a safer 36-byte size.
Patch uses the Lancer-R workaround - which checks for packet <= 32-bytes

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-27 17:11:48 -04:00
David S. Miller a97b7c3aad Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:

====================
Regarding the Bluetooth bits, Gustavo says:

"First Bluetooth fixes to 3.12, it includes:

* 3 patches to add device id for 3 new hardwares.

* 2 patches from Johan to fix the rfkill behaviour during setup stage

* a small clean up in the rfcomm TTY code that fixes a potential racy
condition (by Gianluca Anzolin)

* 2 fixes to proper set encryption key size and security level in the
peripheral role of Bluetooth LE devices. (by Andre Guedes)

* a fix for dealing devices where pairing is not necessary, we were keeping
the Bluetooth ACL connection alive for too much time. (by Syam Sidhardhan)"

Also, I fixed-up an curly-brace indentation problem in the Bluetooth
code while merging.  On top of that...

Alexey Khoroshilov brings a p54usb fix to avoid a resource leak when
request_firmware_nowait fails.

Amitkumar Karwar fixes a firmware hang caused by too much header data
being appended for USB devices using the mwifiex driver.

Arend van Spriel provides three fixes: a brcmfmac fix to relocate some
driver code outside of an .init section; a scheduling while atomic
fix for bcma; and, another scheduling while atomic fix for brcmsmac.

Bing Zhao offers a pair of mwifiex fixes: a code change to avoid
firmware timeouts on USB; and a fix for a NULL pointer dereference.

Christian Lamparter adds a device ID to p54usb.

Felix Fietkau implements a quartet of small ath9k fixes, including
a locking fix, a list management fix, a fix to properly mark a stale
buffer, and an aggregate buffering fix.

Larry Finger champions a data alignment fix to make rtlwifi work
better with ARM builds.

Solomon Peachy reverts an earlier interrupt handling fix for cw1200
and replaces it with a new threaded oneshot irq handler implementation.

Sujith Manoharan fixes an ath9k regression by reverting an earlier
patch.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-27 16:05:34 -04:00
David S. Miller 89f077a085 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to igb and i40e.

Todd provides a fix for 82580 devices in igb, where the ethtool
loopback test was missing 82580 copper devices.

Jesse provides five fixes/cleanups to i40e based on feedback from
Joe Perches and the community.

v2: fixed up patch 5 in the series based on feedback from Joe Perches
    and David Miller
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-27 13:27:49 -04:00
John W. Linville 0a878747e1 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
Also fixed-up a badly indented closing brace...

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-27 13:11:17 -04:00
Jesse Brandeburg d7595a226f i40e: clean up coccicheck reported errors
coccicheck shows:

drivers/net/ethernet/intel/i40e/i40e_adminq.c:704:2-8: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_adminq.c:763:1-7: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_adminq.c:810:2-8: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_common.c:510:2-8: Replace memcpy
with struct assignment

Fix each of them with a *a = *b;

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-09-27 05:24:05 -07:00
Jesse Brandeburg 078b587648 i40e: better return values
As mentioned by Joe Perches, clean up return values in some functions
making sure to have consistent return types, not mixing types.

A couple of Joe's comments suggested returning void, but since
the functions in question are ndo defined, the return values are fixed.
So make a comment in the header that notes this is a function called by
net_device_ops.

v2: fix post increment bug in return

CC: Joe Perches <joe@perches.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-09-27 05:22:30 -07:00
Jesse Brandeburg dcae29be4f i40e: convert ret to aq_ret
When calling admin queue functions the driver should use aq_ret
variable to help make clear that the return value is not a regular
return variable.

This allows for clean up of the return types that were previously
converted to int.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-09-27 04:50:58 -07:00
Jesse Brandeburg ddf434acc0 i40e: small clean ups from review
As mentioned by Joe Perches clean up a loop flow.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joe Perches <joe@perches.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-09-27 04:50:50 -07:00
Jesse Brandeburg 93bc73b827 i40e: use common failure flow
As mentioned by Joe Perches, we should be using
foo = alloc(...)
if (!foo)
	return -ENOMEM;

return 0;

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joe Perches <joe@perches.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-09-27 04:50:46 -07:00
Todd Fujinaka 5aa3a44918 igb: Fix ethtool loopback test for 82580 copper
Add back 82580 loopback tests to ethtool.

Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2013-09-27 04:50:38 -07:00
David S. Miller f875691640 Merge branch 'fixes-for-3.12' of git://gitorious.org/linux-can/linux-can 2013-09-27 02:08:03 -04:00
Roger Luethi 207070f522 via-rhine: fix VLAN priority field (PCP, IEEE 802.1p)
Outgoing packets sent by via-rhine have their VLAN PCP field off by one
(when hardware acceleration is enabled). The TX descriptor expects only VID
and PCP (without a CFI/DEI bit).

Peter Boström noticed and reported the bug.

Signed-off-by: Roger Luethi <rl@hellgate.ch>
Cc: Peter Boström <peter.bostrom@netrounds.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-26 16:09:00 -04:00
Arend van Spriel c7515d2365 brcmsmac: call bcma_core_pci_power_save() from non-atomic context
This patch adds explicit call to bcma_core_pci_power_save() from
a non-atomic context resolving 'scheduling while atomic' issue.

[   13.224317] BUG: scheduling while atomic: dhcpcd/1800/0x00000202
[   13.224322] Modules linked in: brcmsmac nouveau coretemp kvm_intel kvm cordic brcmutil bcma dell_wmi atl1c ttm mxm_wmi wmi
[   13.224354] CPU: 0 PID: 1800 Comm: dhcpcd Tainted: G        W    3.11.0-wl #1
[   13.224359] Hardware name: Alienware M11x R2/M11x R2, BIOS A04 11/23/2010
[   13.224363]  ffff880177c12c40 ffff880170fd1968 ffffffff8169af5b 0000000000000007
[   13.224374]  ffff880170fd1ad0 ffff880170fd1978 ffffffff81697ee2 ffff880170fd19f8
[   13.224383]  ffffffff816a19f5 00000000000f4240 000000000000d080 ffff880170fd1fd8
[   13.224391] Call Trace:
[   13.224399]  [<ffffffff8169af5b>] dump_stack+0x4f/0x84
[   13.224403]  [<ffffffff81697ee2>] __schedule_bug+0x43/0x51
[   13.224409]  [<ffffffff816a19f5>] __schedule+0x6e5/0x810
[   13.224412]  [<ffffffff816a1c34>] schedule+0x24/0x70
[   13.224416]  [<ffffffff816a04fc>] schedule_hrtimeout_range_clock+0x10c/0x150
[   13.224420]  [<ffffffff810684e0>] ? update_rmtp+0x60/0x60
[   13.224424]  [<ffffffff8106915f>] ? hrtimer_start_range_ns+0xf/0x20
[   13.224429]  [<ffffffff816a054e>] schedule_hrtimeout_range+0xe/0x10
[   13.224432]  [<ffffffff8104f6fb>] usleep_range+0x3b/0x40
[   13.224437]  [<ffffffffa003733a>] bcma_pcie_mdio_read.isra.5+0x8a/0x100 [bcma]
[   13.224442]  [<ffffffffa00374a5>] bcma_pcie_mdio_writeread.isra.6.constprop.13+0x25/0x30 [bcma]
[   13.224448]  [<ffffffffa00374f9>] bcma_core_pci_power_save+0x49/0x80 [bcma]
[   13.224452]  [<ffffffffa003765d>] bcma_core_pci_up+0x2d/0x60 [bcma]
[   13.224460]  [<ffffffffa03dc17c>] brcms_c_up+0xfc/0x430 [brcmsmac]
[   13.224467]  [<ffffffffa03d1a7d>] brcms_up+0x1d/0x20 [brcmsmac]
[   13.224473]  [<ffffffffa03d2498>] brcms_ops_start+0x298/0x340 [brcmsmac]
[   13.224478]  [<ffffffff81600a12>] ? cfg80211_netdev_notifier_call+0xd2/0x5f0
[   13.224483]  [<ffffffff815fa53d>] ? packet_notifier+0xad/0x1d0
[   13.224487]  [<ffffffff81656e75>] ieee80211_do_open+0x325/0xf80
[   13.224491]  [<ffffffff8106ac09>] ? __raw_notifier_call_chain+0x9/0x10
[   13.224495]  [<ffffffff81657b41>] ieee80211_open+0x71/0x80
[   13.224498]  [<ffffffff81526267>] __dev_open+0x87/0xe0
[   13.224502]  [<ffffffff8152650c>] __dev_change_flags+0x9c/0x180
[   13.224505]  [<ffffffff815266a3>] dev_change_flags+0x23/0x70
[   13.224509]  [<ffffffff8158cd68>] devinet_ioctl+0x5b8/0x6a0
[   13.224512]  [<ffffffff8158d5c5>] inet_ioctl+0x75/0x90
[   13.224516]  [<ffffffff8150b38b>] sock_do_ioctl+0x2b/0x70
[   13.224519]  [<ffffffff8150b681>] sock_ioctl+0x71/0x2a0
[   13.224523]  [<ffffffff8114ed47>] do_vfs_ioctl+0x87/0x520
[   13.224528]  [<ffffffff8113f159>] ? ____fput+0x9/0x10
[   13.224533]  [<ffffffff8106228c>] ? task_work_run+0x9c/0xd0
[   13.224537]  [<ffffffff8114f271>] SyS_ioctl+0x91/0xb0
[   13.224541]  [<ffffffff816aa252>] system_call_fastpath+0x16/0x1b

Cc: <stable@vger.kernel.org> # 3.11.x
Cc: Tod Jackson <tod.jackson@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26 14:02:34 -04:00
Arend van Spriel 2bedea8f26 bcma: make bcma_core_pci_{up,down}() callable from atomic context
This patch removes the bcma_core_pci_power_save() call from
the bcma_core_pci_{up,down}() functions as it tries to schedule
thus requiring to call them from non-atomic context. The function
bcma_core_pci_power_save() is now exported so the calling module
can explicitly use it in non-atomic context. This fixes the
'scheduling while atomic' issue reported by Tod Jackson and
Joe Perches.

[   13.210710] BUG: scheduling while atomic: dhcpcd/1800/0x00000202
[   13.210718] Modules linked in: brcmsmac nouveau coretemp kvm_intel kvm cordic brcmutil bcma dell_wmi atl1c ttm mxm_wmi wmi
[   13.210756] CPU: 2 PID: 1800 Comm: dhcpcd Not tainted 3.11.0-wl #1
[   13.210762] Hardware name: Alienware M11x R2/M11x R2, BIOS A04 11/23/2010
[   13.210767]  ffff880177c92c40 ffff880170fd1948 ffffffff8169af5b 0000000000000007
[   13.210777]  ffff880170fd1ab0 ffff880170fd1958 ffffffff81697ee2 ffff880170fd19d8
[   13.210785]  ffffffff816a19f5 00000000000f4240 000000000000d080 ffff880170fd1fd8
[   13.210794] Call Trace:
[   13.210813]  [<ffffffff8169af5b>] dump_stack+0x4f/0x84
[   13.210826]  [<ffffffff81697ee2>] __schedule_bug+0x43/0x51
[   13.210837]  [<ffffffff816a19f5>] __schedule+0x6e5/0x810
[   13.210845]  [<ffffffff816a1c34>] schedule+0x24/0x70
[   13.210855]  [<ffffffff816a04fc>] schedule_hrtimeout_range_clock+0x10c/0x150
[   13.210867]  [<ffffffff810684e0>] ? update_rmtp+0x60/0x60
[   13.210877]  [<ffffffff8106915f>] ? hrtimer_start_range_ns+0xf/0x20
[   13.210887]  [<ffffffff816a054e>] schedule_hrtimeout_range+0xe/0x10
[   13.210897]  [<ffffffff8104f6fb>] usleep_range+0x3b/0x40
[   13.210910]  [<ffffffffa00371af>] bcma_pcie_mdio_set_phy.isra.3+0x4f/0x80 [bcma]
[   13.210921]  [<ffffffffa003729f>] bcma_pcie_mdio_write.isra.4+0xbf/0xd0 [bcma]
[   13.210932]  [<ffffffffa0037498>] bcma_pcie_mdio_writeread.isra.6.constprop.13+0x18/0x30 [bcma]
[   13.210942]  [<ffffffffa00374ee>] bcma_core_pci_power_save+0x3e/0x80 [bcma]
[   13.210953]  [<ffffffffa003765d>] bcma_core_pci_up+0x2d/0x60 [bcma]
[   13.210975]  [<ffffffffa03dc17c>] brcms_c_up+0xfc/0x430 [brcmsmac]
[   13.210989]  [<ffffffffa03d1a7d>] brcms_up+0x1d/0x20 [brcmsmac]
[   13.211003]  [<ffffffffa03d2498>] brcms_ops_start+0x298/0x340 [brcmsmac]
[   13.211020]  [<ffffffff81600a12>] ? cfg80211_netdev_notifier_call+0xd2/0x5f0
[   13.211030]  [<ffffffff815fa53d>] ? packet_notifier+0xad/0x1d0
[   13.211064]  [<ffffffff81656e75>] ieee80211_do_open+0x325/0xf80
[   13.211076]  [<ffffffff8106ac09>] ? __raw_notifier_call_chain+0x9/0x10
[   13.211086]  [<ffffffff81657b41>] ieee80211_open+0x71/0x80
[   13.211101]  [<ffffffff81526267>] __dev_open+0x87/0xe0
[   13.211109]  [<ffffffff8152650c>] __dev_change_flags+0x9c/0x180
[   13.211117]  [<ffffffff815266a3>] dev_change_flags+0x23/0x70
[   13.211127]  [<ffffffff8158cd68>] devinet_ioctl+0x5b8/0x6a0
[   13.211136]  [<ffffffff8158d5c5>] inet_ioctl+0x75/0x90
[   13.211147]  [<ffffffff8150b38b>] sock_do_ioctl+0x2b/0x70
[   13.211155]  [<ffffffff8150b681>] sock_ioctl+0x71/0x2a0
[   13.211169]  [<ffffffff8114ed47>] do_vfs_ioctl+0x87/0x520
[   13.211180]  [<ffffffff8113f159>] ? ____fput+0x9/0x10
[   13.211198]  [<ffffffff8106228c>] ? task_work_run+0x9c/0xd0
[   13.211202]  [<ffffffff8114f271>] SyS_ioctl+0x91/0xb0
[   13.211208]  [<ffffffff816aa252>] system_call_fastpath+0x16/0x1b
[   13.211217] NOHZ: local_softirq_pending 202

The issue was introduced in v3.11 kernel by following commit:

commit aa51e598d0
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date:   Sat Aug 24 00:32:31 2013 +0200

    brcmsmac: use bcma PCIe up and down functions

    replace the calls to bcma_core_pci_extend_L1timer() by calls to the
    newly introduced bcma_core_pci_ip() and bcma_core_pci_down()

    Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
    Cc: Arend van Spriel <arend@broadcom.com>
    Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fix has been discussed with Hauke Mehrtens [1] selection
option 3) and is intended for v3.12.

Ref:
[1] http://mid.gmane.org/5239B12D.3040206@hauke-m.de

Cc: <stable@vger.kernel.org> # 3.11.x
Cc: Tod Jackson <tod.jackson@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26 14:02:33 -04:00
Arend van Spriel db4efbbeb4 brcmfmac: obtain platform data upon module initialization
The driver uses platform_driver_probe() to obtain platform data
if any. However, that function is placed in the .init section so
it must be called upon driver module initialization.

The problem was reported by Fenguang Wu resulting in a kernel
oops because the .init section was already freed.

[   48.966342] Switched to clocksource tsc
[   48.970002] kernel tried to execute NX-protected page - exploit attempt? (uid: 0)
[   48.970851] BUG: unable to handle kernel paging request at ffffffff82196446
[   48.970957] IP: [<ffffffff82196446>] classes_init+0x26/0x26
[   48.970957] PGD 1e76067 PUD 1e77063 PMD f388063 PTE 8000000002196163
[   48.970957] Oops: 0011 [#1]
[   48.970957] CPU: 0 PID: 17 Comm: kworker/0:1 Not tainted 3.11.0-rc7-00444-gc52dd7f #23
[   48.970957] Workqueue: events brcmf_driver_init
[   48.970957] task: ffff8800001d2000 ti: ffff8800001d4000 task.ti: ffff8800001d4000
[   48.970957] RIP: 0010:[<ffffffff82196446>]  [<ffffffff82196446>] classes_init+0x26/0x26
[   48.970957] RSP: 0000:ffff8800001d5d40  EFLAGS: 00000286
[   48.970957] RAX: 0000000000000001 RBX: ffffffff820c5620 RCX: 0000000000000000
[   48.970957] RDX: 0000000000000001 RSI: ffffffff816f7380 RDI: ffffffff820c56c0
[   48.970957] RBP: ffff8800001d5d50 R08: ffff8800001d2508 R09: 0000000000000002
[   48.970957] R10: 0000000000000000 R11: 0001f7ce298c5620 R12: ffff8800001c76b0
[   48.970957] R13: ffffffff81e91d40 R14: 0000000000000000 R15: ffff88000e0ce300
[   48.970957] FS:  0000000000000000(0000) GS:ffffffff81e84000(0000) knlGS:0000000000000000
[   48.970957] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[   48.970957] CR2: ffffffff82196446 CR3: 0000000001e75000 CR4: 00000000000006b0
[   48.970957] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   48.970957] DR3: 0000000000000000 DR6: 0000000000000000 DR7: 0000000000000000
[   48.970957] Stack:
[   48.970957]  ffffffff816f7df8 ffffffff820c5620 ffff8800001d5d60 ffffffff816eeec9
[   48.970957]  ffff8800001d5de0 ffffffff81073dc5 ffffffff81073d68 ffff8800001d5db8
[   48.970957]  0000000000000086 ffffffff820c5620 ffffffff824f7fd0 0000000000000000
[   48.970957] Call Trace:
[   48.970957]  [<ffffffff816f7df8>] ? brcmf_sdio_init+0x18/0x70
[   48.970957]  [<ffffffff816eeec9>] brcmf_driver_init+0x9/0x10
[   48.970957]  [<ffffffff81073dc5>] process_one_work+0x1d5/0x480
[   48.970957]  [<ffffffff81073d68>] ? process_one_work+0x178/0x480
[   48.970957]  [<ffffffff81074188>] worker_thread+0x118/0x3a0
[   48.970957]  [<ffffffff81074070>] ? process_one_work+0x480/0x480
[   48.970957]  [<ffffffff8107aa17>] kthread+0xe7/0xf0
[   48.970957]  [<ffffffff810829f7>] ? finish_task_switch.constprop.57+0x37/0xd0
[   48.970957]  [<ffffffff8107a930>] ? __kthread_parkme+0x80/0x80
[   48.970957]  [<ffffffff81a6923a>] ret_from_fork+0x7a/0xb0
[   48.970957]  [<ffffffff8107a930>] ? __kthread_parkme+0x80/0x80
[   48.970957] Code: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
cc cc cc cc cc cc <cc> cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
[   48.970957] RIP  [<ffffffff82196446>] classes_init+0x26/0x26
[   48.970957]  RSP <ffff8800001d5d40>
[   48.970957] CR2: ffffffff82196446
[   48.970957] ---[ end trace 62980817cd525f14 ]---

Cc: <stable@vger.kernel.org> # 3.10.x, 3.11.x
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26 14:02:33 -04:00
Bing Zhao 346ece0b7b mwifiex: fix NULL pointer dereference in usb suspend handler
Bug 60815 - Interface hangs in mwifiex_usb
https://bugzilla.kernel.org/show_bug.cgi?id=60815

[ 2.883807] BUG: unable to handle kernel NULL pointer dereference
            at 0000000000000048
[ 2.883813] IP: [<ffffffff815a65e0>] pfifo_fast_enqueue+0x90/0x90

[ 2.883834] CPU: 1 PID: 3220 Comm: kworker/u8:90 Not tainted
            3.11.1-monotone-l0 #6
[ 2.883834] Hardware name: Microsoft Corporation Surface with
            Windows 8 Pro/Surface with Windows 8 Pro,
            BIOS 1.03.0450 03/29/2013

On Surface Pro, suspend to ram gives a NULL pointer dereference in
pfifo_fast_enqueue(). The stack trace reveals that the offending
call is clearing carrier in mwifiex_usb suspend handler.

Since commit 1499d9f "mwifiex: don't drop carrier flag over suspend"
has removed the carrier flag handling over suspend/resume in SDIO
and PCIe drivers, I'm removing it in USB driver too. This also fixes
the bug for Surface Pro.

Cc: <stable@vger.kernel.org> # 3.5+
Tested-by: Dmitry Khromov <icechrome@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26 14:02:33 -04:00
Amitkumar Karwar bd1c6142ed mwifiex: fix hang issue for USB chipsets
Bug 60815 - Interface hangs in mwifiex_usb
https://bugzilla.kernel.org/show_bug.cgi?id=60815

We have 4 bytes of interface header for packets delivered to SDIO
and PCIe, but not for USB interface.

In Tx AMSDU case, currently 4 bytes of garbage data is unnecessarily
appended for USB packets. This sometimes leads to a firmware hang,
because it may not interpret the data packet correctly.

Problem is fixed by removing this redundant headroom for USB.

Cc: <stable@vger.kernel.org> # 3.5+
Tested-by: Dmitry Khromov <icechrome@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26 14:02:32 -04:00
Christian Lamparter 1e43692cdb p54usb: add USB ID for Corega WLUSB2GTST USB adapter
Added USB ID for Corega WLUSB2GTST USB adapter.

Cc: <stable@vger.kernel.org>
Reported-by: Joerg Kalisch <the_force@gmx.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26 14:02:32 -04:00
Solomon Peachy 87421cb601 cw1200: Use a threaded oneshot irq handler for cw1200_spi
This supercedes the older patch ("cw1200: Don't perform SPI transfers in
interrupt context") that badly attempted to fix this problem.

This is a far simpler solution, which has the added benefit of
actually working.

Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26 14:02:31 -04:00
Solomon Peachy c4fb19d21b Revert "cw1200: Don't perform SPI transfers in interrupt context"
This reverts commit aec8e88c94.

This solution turned out to cause interrupt delivery problems, and
rather than trying to fix this approach, it has been scrapped in favor
of an alternative (and far simpler) implementation.

Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26 14:02:31 -04:00
Bing Zhao b7be1522de mwifiex: fix PCIe hs_cfg cancel cmd timeout
For pcie8897, the hs_cfg cancel command (0xe5) times out when host
comes out of suspend. This is caused by an incompleted host sleep
handshake between driver and firmware.

Like SDIO interface, PCIe also needs to go through firmware power
save events to complete the handshake for host sleep configuration.
Only USB interface doesn't require power save events for hs_cfg.

Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26 14:02:31 -04:00
Larry Finger 60ce314d17 rtlwifi: Align private space in rtl_priv struct
The private array at the end of the rtl_priv struct is not aligned.
On ARM architecture, this causes an alignment trap and is fixed by aligning
that array with __align(sizeof(void *)). That should properly align that
space according to the requirements of all architectures.

Reported-by: Jason Andrews <jasona@cadence.com>
Tested-by: Jason Andrews <jasona@cadence.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26 14:02:30 -04:00
Felix Fietkau 919123d246 ath9k: add txq locking for ath_tx_aggr_start
Prevents race conditions when un-aggregated frames are pending in the
driver.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26 14:02:30 -04:00
Alexey Khoroshilov e78641c19d p54usb: fix leak at failure path in p54u_load_firmware()
If request_firmware_nowait() fails in p54u_load_firmware(),
p54u_load_firmware_cb is not called and no one decrements usb_dev refcnt.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26 14:02:29 -04:00
Felix Fietkau 20e6e55aaa ath9k: don't use BAW tracking on PS responses for non-AMPDU packets
When .release_buffered_frames was implemented, only A-MPDU packets were
buffered internally. Now that this has changed, the BUF_AMPDU flag needs
to be checked before calling ath_tx_addto_baw

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26 14:02:29 -04:00