Commit 6d98bda79b changed the init order
for chrp_pci_fixup_vt8231_ata().
It can not work anymore because either the irq is not yet set to 14 or
pci_get_device() returns nothing. At least the printk() in
chrp_pci_fixup_vt8231_ata() does not trigger anymore.
pata_via works again on Pegasos with the change below.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently the IOMMU code allocates one page for the segment table, that
isn't safe if we have more than 132 GB of RAM.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rather than using the global variable, have celleb use its own
variable to store the direct DMA offset.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rather than using the global variable, have cell use its own variable
to store the direct DMA offset.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Celleb always uses dma_direct_ops, and sets dma_direct_offset, so it
too should set dma_data to dma_direct_offset.
Currently there's no pci_dma_dev_setup() routine for Celleb so add one.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Store the direct_dma_offset in each device's dma_data in the case
where we're using the direct DMA ops.
We need to make sure we setup the ppc_md.pci_dma_dev_setup() callback
if we're using a non-zero offset.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the PS3 workaround needed to support sparsemem SPU mappings.
The SPU mappings no longer use sparsemem, so this workaround is no
longer needed.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add PS3 logical performance monitor (lpm) device driver.
The PS3's LV1 hypervisor provides a Logical Performance Monitor that
abstracts the Cell processor's performance monitor features for use
by guest operating systems.
Signed-off-by: Takashi Yamamoto <TakashiA.Yamamoto@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add PS3 logical performance monitor device support to the
PS3 system-bus and platform device registration routines.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup coding errors in arch/powerpc/platforms/ps3/repository.c as
reported by sparse and checkpatch.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PS3: Add repository polling loop to work around timing bug
On some firmware versions (e.g. 1.90), the storage device may not show up
in the repository immediately after receiving the notification message.
Add a small polling loop to make sure we don't miss it.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PS3 hypervisor has a storage device notification mechanism to wait
until a storage device is ready. Unfortunately the storage device
probing code used this mechanism in an incorrect way, needing a
polling loop and handling of devices that are not yet ready.
This change corrects this by:
- First waiting for the reception of an asynchronous notification
that a new storage device became ready,
- Then looking up the storage device in the device repository.
On shutdown, the storage probe thread is stopped and the storage
notification device is closed using a reboot notifier.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The storage probe feature of the PS3 hypervisor returns device IDs. Add
the corresponding repository routine ps3_repository_find_device_by_id()
which can be used to retrieve the device info from the repository.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the PS3 bus_id and dev_id from type unsigned int to u64. These
IDs are 64-bit in the repository, and the special storage notification
device has a device ID of ULONG_MAX.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
/sys/power should not be a kset, that's overkill. This patch renames it
to power_kset and fixes up all usages of it in the tree.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes the code a bit simpler and and gets us one step closer to
deleting the deprecated subsys_attr code.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dynamically create the kset instead of declaring it statically. We also
rename power_subsys to power_kset to catch all users of the variable and
we properly export it so that people don't have to guess that it really
is present in the system.
The pseries code is wierd, why is it createing /sys/power if CONFIG_PM
is disabled? Oh well, stupid big boxes ignoring config options...
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need a "default" ktype for a kset. We should set this
explicitly every time for each kset. This change is needed so that we
can make ksets dynamic, and cleans up one of the odd, undocumented
assumption that the kset/kobject/ktype model has.
This patch is based on a lot of help from Kay Sievers.
Nasty bug in the block code was found by Dave Young
<hidave.darkstar@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use cuImage bootwrapper until U-Boot port is completed.
Derived heavily from Linkstation port.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Wilcox <andy@protium.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Prevents miscellaneous users from declaring it locally.
Signed-off-by: Jon Loeliger <jdl@freecale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Call of_platform_bus_probe() on the MPC8641 HPCN, similar to what is
done for other platforms.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add NAND to device tree, and call of_platform_bus_probe().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This board is also resold by Freescale under the names
"QUICCStart MPC8248 Evaluation System" and "CWH-PPC-8248N-VE".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update the MPC8610 HPCD files to support the audio driver. Update
booting-without-of.txt with information on the SSI device.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
IPIC is not just for 83xx anymore so make it a separate config option.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add in missing of_node_put() after cpm2_pic_init(). This and other coding
style cleanups as suggested by Stephen Rothwell.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Define the layout of a binary blob that contains a QE firmware and instructions
on how to upload it. Add function qe_upload_firmware() to parse the blob
and perform the actual upload. Fully define 'struct rsp' in immap_qe.h to
include the actual RISC Special Registers. Added description of a new
QE firmware node to booting-without-of.txt.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds localbus and pata nodes to use CF IDE interface
on MPC8349E-mITX boards.
Patch also adds code to probe localbus.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove device_type = "usb" for 83xx SoC USB controller
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add chip specific and board specific initialization for MPC837x USB.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for 'mpc5200-simple-platform' compatible
boards which do not need a platform specific setup. Such boards
are supported assuming the following:
- GPIO pins are configured by the firmware,
- CDM configuration (clocking) is setup correctly by firmware,
- if the 'fsl,has-wdt' property is present in one of the
gpt nodes, then it is safe to use such gpt to reset the board,
- PCI is supported if enabled in the kernel configuration
and if there is a PCI bus node defined in the device tree.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
mpc5200 platform code defines a bunch of map functions which duplicate the
functionality of of_iomap(). Remove them and use of_iomap() instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch moves a generic pci init code from lite5200
platform file to a common mpc52xx_setup_pci() routine
and adds additional compatibility property verification.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Define MPC52xx specific device id list, add new
'fsl,lpb' compatible id for LocalPlus Bus.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
xlate_iomm_address() really wants the ds_addr to pass to the HV, so store
that value (instead of the BAR number) when we allocate the device bars.
This is not a fast path, so we can look up the device_node property
there instead of using the bussubno field of the pci_dn.
The other user of iseries_ds_addr() was already scanning the device tree,
so looking up a property will not slow it down any more.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Similar to of_find_compatible_node(), of_find_matching_node() and
for_each_matching_node() allow you to iterate over the device tree
looking for specific nodes, except that they take of_device_id
tables instead of strings.
This also moves of_match_node() from driver/of/device.c to
driver/of/base.c to colocate it with the of_find_matching_node which
depends on it.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move electra-ide glue over to the new pata_of_platform framework, and
add the quirks needed to that driver.
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 473980a993 added a call to clear
the SLB shadow buffer before registering it. Unfortunately this means
that we clear out the entries that slb_initialize has previously set in
there. On POWER6, the hypervisor uses the SLB shadow buffer when doing
partition switches, and that means that after the next partition switch,
each non-boot CPU has no SLB entries to map the kernel text and data,
which causes it to crash.
This fixes it by reverting most of 473980a9 and instead clearing the
3rd entry explicitly in slb_initialize. This fixes the problem that
473980a9 was trying to solve, but without breaking POWER6.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Before we register the SLB shadow buffer, we need to invalidate the
entries in the buffer, otherwise we can end up stale entries from when
we previously offlined the CPU.
This does this invalidate as well as unregistering the buffer with
PHYP before we offline the cpu. Tested and fixes crashes seen on
970MP (thanks to tonyb) and POWER5.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Includes both flavors of plb, opb, dcr, and a pseudo 'compound' bus
for representing compound peripherals containing more than one logical
device.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The logic that checks to see if a machine check is caused by an NMI will
always match when NMI hasn't been initialized, since the mpic routine
will return NO_IRQ (and that's what the nmi_virq value is as well).
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit aed3a8c9bb introduced a
definition of notify_spus_active in .../cell/spu_syscalls.c, and
another definition under #ifndef MODULE in .../cell/spufs/sched.c.
The latter is not necessary and causes the build to fail when
CONFIG_SPU_FS=y, so this removes it. It also removes the export
of do_notify_spus_active, which is unnecessary.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
By default the OpenPIC on PWRficient will bias to one core (since that
will improve changes of the other core being able to stay idle/powered
down). However, this conflicts with most irq load balancing schemes,
since setting an interrupt to be delivered to either core doesn't really
result in the load being shared. It also doesn't work well with the
soft irq disable feature of PPC, since EE will stay on until the first
interrupt is taken while soft disabled.
Set the gconf0 config bit that enables even distribution of interrupts
among the two cores.
Signed-off-by: Olof Johansson <olof@lixom.net>
Some PWRficient-based boards have a NMI button that's wired up to a GPIO
as interrupt source. By configuring the openpic accordingly, these get
delivered as a machine check with high priority, instead of as an external
interrupt.
The device tree contains a property "nmi-source" in the openpic node
for these systems, and it's the (hwirq) source for the input.
Also, for these interrupts, the IACK is read from another register than
the regular (MCACK instead), but they are EOI'd as usual. So implement
said function for the mpic driver.
Finally, move a couple of external function defines to include/ instead
of local under sysdev. Being able to mask/unmask and eoi directly saves
us from setting up a dummy irq handler that will never be called.
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix a bug in the printing of the os-area magic numbers which assumed
that magic numbers were zero terminated strings. The magic numbers
are represented in memory as integers. If the os-area sections are
not initialized correctly they could contained random data that would
be printed to the display. Also unify the handling of header and db
magic numbers and make both of type array of u8.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes an OProfile dependency on the spufs module. This
dependency was causing a problem for multiplatform systems that are
built with support for Oprofile on Cell but try to load the oprofile
module on a non-Cell system.
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some machine_xx_initcall macros were recently added that check for the machine
type before calling the function. This converts the 4xx platforms to use those
for bus probing.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Remove the declarations for isa_io_base and isa_mem_base as they are declared
in pci-common.c now.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Enable PCI support for these eval boards among other things. Also selects
PCI for Rainier in the Kconfig file.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds basic support for the AMCC Makalu board to arch/powerpc.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
For EMAC support, 405EX needs to be defined to enable the corresponding
EMAC features (IBM_NEW_EMAC_EMAC4, etc.).
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
A small error caused a header file to be removed making sequoia support no
longer compile. Fix it.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This makes 4xx embedded platforms re-assign all PCI resources as we
pretty much never care about what the various firmwares have done on
these, it's generally not compatible with the way the kernel will map
the bridges.
We still need to also enable bus renumbering on some of them, but I
will do that from a separate patch after I've fixed 4xx PCIe to handle
all bus numbers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds base support for the Katmai board, including PCI-X and
PCI-Express (but no RTC, nvram, etc... yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds the device-tree bits & call to ppc4xx_pci_find_bridges()
to make PCI work on the Bamboo board
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds base support for the AMCC Taishan 440GX evaluation
board.
Signed-off-by: Hugh Blemings <hugh@blemings.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This wires up the 4xx PCI support & device-tree bits for the
405GP based Walnut platform.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Brings EP405 support to arch/powerpc. The IRQ routing for the CPLD
comes from a device-tree property, PCI is working to the point where
I can see the video card, USB device, and south bridge.
This should work with both EP405 and EP405PC.
I've not totally figured out how IRQs are wired on this hardware
though, thus at this stage, expect only USB interrupts working,
pretty much the same as what arch/ppc did.
Also, the flash, nvram, rtc and temp control still have to be wired.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds some basic real mode based early udbg support for 40x
in order to debug things more easily
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This wires up the 4xx PCI support & device tree bits for
440GP based Ebony platform.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds a cputable function pointer for the CPU-side machine
check handling. The semantic is still the same as the old one,
the one in ppc_md. overrides the one in cputable, though
ultimately we'll want to change that so the CPU gets first.
This removes CONFIG_440A which was a problem for multiplatform
kernels and instead fixes up the IVOR at runtime from a setup_cpu
function. The "A" version of the machine check also tweaks the
regs->trap value to differenciate the 2 versions at the C level.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Maple and pasemi both require PCI as does CONFIG_OF_PLATFORM_PCI.
The default setting of CONFIG_ISA_DMA_API is set to match the protection
around the relevant routines in asm/dma.h.
I also had to remove the PMAC platform from the combined build. The
precis is that to build a 64 bit kernel with no PCI, you can only include
pSeries and iSeries.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Based on an original patch from Arnd Bergmann
<arnd.bergmann@de.ibm.com>
If there's no entry in the mailbox, then a read on the _info file will
return data from an uninitialised variable.
This change returns EOF if there's no mailbox info available instead.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the behavior of spufs when a spu tries a DMA operation
based on a wrong / unavailable address.
Instead of just generating a SIGBUS signal, spufs now
generates a SIGSEGV signal and restarts the problematic DMA operation
after the execution of the application's signal handler. This allows
applications to employ user-level paging systems.
Although the restart_dma function is called before the application's
signal handler, the operation is not actually performed at this time,
since the spu context is already stopped. The operation only takes
place when spu_run is restarted (which happens automatically).
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The original spusched_timer was designed to take effect only when
a context is waiting in the runqueue.
This change adds an additional lower-freq timer has been added to
purely handle the spu_load updates. The new timer will be triggered
per LOAD_FREQ ticks.
Signed-off-by: Aegis Lin <aegislin@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make most places that use spu_acquire/spu_acquire_saved interruptible,
this allows getting out of the spufs code when e.g. pressing ctrl+c.
There are a few places where we get called e.g. from spufs teardown
routines were we can't simply err out so these are left with a comment.
For now I've also not touched the poll routines because it's open what
libspe would expect in terms of interrupted system calls.
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The simple attr macros currently used by spufs can't deal with the
handlers returning errors, which is required to make the state_mutex
interruptible. This adds a local copy that allows for an error
return from the get/set handlers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change spufs_spu_run so that the context is queued directly to the
scheduler and the controlling thread advances directly to spufs_wait()
for spe errors and exceptions.
nosched contexts are treated the same as before.
Fixes from Christoph Hellwig <hch@lst.de>
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes the spu context switch code to not write to reserved bits
of spu interrupt status register.
The architecture book says the reserved fields should be set to zero.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Need to re-check priority after dropping lock. Otherwise, a
more favored context may be preempted.
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This cleans up spu_run_init so that it does all of the spu
initialization for spufs_run_spu. It initializes the spu context as
much as possible before it activates the spu and writes the runcntl
register.
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Based on original patches from
Arnd Bergmann <arnd.bergman@de.ibm.com>; and
Luke Browning <lukebr@linux.vnet.ibm.com>
Currently, spu contexts need to be loaded to the SPU in order to take
class 0 and class 1 exceptions.
This change makes the actual interrupt-handlers much simpler (ie,
set the exception information in the context save area), and defers the
handling code to the spufs_handle_class[01] functions, called from
spufs_run_spu.
This should improve the concurrency of the spu scheduling leading to
greater SPU utilization when SPUs are overcommited.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a few #defines for the class 0, 1 and 2 interrupt status bits, and
use them instead of magic numbers when we're setting or checking for
these interrupts.
Also, add a #define for the class 2 mailbox threshold interrupt mask.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When doing a poll on the mbox stat file of a swapped-out context, we
clear the class 0 interrupt status, rather than the class 2 interrupt
status.
This change corrects the poll operation to clear the correct interrupt.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This change encapsulates the spu_privcntl_RW register so that it can
be written through backing ops. This is necessary so that spu contexts
can be initialized and queued to the scheduler in spufs_run_spu.
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This change disables the logic that faults-in spu contexts under the
covers from the page fault handler. When a fault requires a runnable
context, the handler will block until the context is scheduled by
other means.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, part of the spufs code (switch.o, lscsa_alloc.o and fault.o)
is compiled directly into the kernel.
This change moves these components of spufs into the kernel.
The lscsa and switch objects are fairly straightforward to move in.
For the fault.o module, we split the fault-handling code into two
parts: a/p/p/c/spu_fault.c and a/p/p/c/spufs/fault.c. The former is for
the in-kernel spu_handle_mm_fault function, and we move the rest of the
fault-handling code into spufs.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix a few typos in the spufs scheduler comments
Signed-off-by: Julio M. Merino Vidal <jmerino@ac.upc.edu>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add platform specific SPU run control routines to the spufs. The current
spufs implementation uses the SPU master run control bit (MFC_SR1[S]) to
control SPE execution, but the PS3 hypervisor does not support the use of
this feature.
This change adds the run control wrapper routies spu_enable_spu() and
spu_disable_spu(). The bare metal routines use the master run control
bit, and the PS3 specific routines use the priv2 run control register.
An outstanding enhancement for the PS3 would be to add a guard to check
for incorrect access to the spu problem state when the spu context is
disabled. This check could be implemented with a flag added to the spu
context that would inhibit mapping problem state pages, and a routine
to unmap spu problem state pages. When the spu is enabled with
ps3_enable_spu() the flag would be set allowing pages to be mapped,
and when the spu is disabled with ps3_disable_spu() the flag would be
cleared and mapped problem state pages would be unmapped.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There should be an of_node_put when breaking out of a loop that iterates
using for_each_node_by_type.
This was detected and fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
identifier d;
type T;
expression e;
iterator for_each_node_by_type;
@@
T *d;
...
for_each_node_by_type(d,...)
{... when != of_node_put(d)
when != e = d
(
return d;
|
+ of_node_put(d);
? return ...;
)
...}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Christian Krafft <krafft@de.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Erb <djerb@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There should be an of_node_put when breaking out of a loop that iterates
over calls to of_find_all_nodes, as this function does an of_node_get on
the value it returns.
This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
identifier d;
expression e;
@@
T *d;
...
for (d = NULL; (d = of_find_all_nodes(d)) != NULL; )
{... when != of_node_put(d)
when != e = d
(
return d;
|
+ of_node_put(d);
? return ...;
)
...}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Lucas Woods <woodzy@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a possible NULL pointer dereference inside of strncmp() if
of_get_property() fails.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The device node for the HT bridge on G5s doesn't contain useful ranges.
We used to give it a bunch of the known PCI space and then punch a "hole"
in it based on where the AGP or PCIe region was. This reworks it to
use the actual register in the bridge that controls the decoding instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This enables the PCI code to see the device that represents the
HT host bridge on the PowerMac G5.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It should now be safe to re-assign unassigned resources on 64 bits PowerMac
machines (G5s). This clears pci_probe_only on those.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Powermac's use of the pcibios_enable_device_hook() got slightly
broken by the recent PCI merge in that it won't be called for
the "initial" case of assigning resources to a previously
unassigned device. This was an abuse of that hook anyway, so
instead we now use a header quirk.
While at it, we move a #ifdef CONFIG_PPC32 to enclose more code
that is only ever used on 32 bits.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This merge the two implementations, based on the previously
fixed up 32 bits one. The pcibios_enable_device_hook in ppc_md
is now available for ppc64 use. Also remove the new unused
"initial" parameter from it and fixup users.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The way iSeries manages PCI IO and Memory resources is a bit strange
and is based on overriding the content of those resources with home
cooked ones afterward.
This changes it a bit to better integrate with the new resource handling
so that the "virtual" tokens that iSeries replaces resources with are
done from the proper per-device fixup hook, and bridge resources are
set to enclose that token space. This fixes various things such as
the output of /proc/iomem & ioports, among others. This also fixes up
various boot messages as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32 bits PCI code now uses the generic code for assigning unassigned
resources and an algorithm similar to x86 for claiming existing ones.
This works far better than the 64 bits code which basically can only
claim existing ones (pci_probe_only=1) or would fall apart completely.
This merges them so that the new 32 bits implementation is used for both.
64 bits now gets the new PCI flags for controlling the behaviour, though
the old pci_probe_only global is still there for now to be cleared if you
want to.
I kept a pcibios_claim_one_bus() function mostly based on the old 64
bits code for use by the DLPAR hotplug. This will have to be cleaned
up, thought I hope it will work in the meantime.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PCI code in 32 and 64 bits fixes up resources differently.
32 bits uses a header quirk plus handles bridges in pcibios_fixup_bus()
while 64 bits does things in various places depending on whether you
are using OF probing, using PCI hotplug, etc...
This merges those by basically using the 32 bits approach for both,
with various tweaks to make 64 bits work with the new approach.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds to the 32 bits PCI code some flags, replacing the old
pci_assign_all_busses global, that allow us to control various
aspects of the PCI probing, such as whether to re-assign all
resources or not, or to not try to assign anything at all.
This also adds the flag x86 already has to avoid ISA alignment
on bridges that don't have ISA forwarding enabled (no legacy
devices on the top level bus) and sets it for PowerMacs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's nothing in holly.c that needs linux/ide.h, just remove it from
the list of includes.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The per-processor interrupt request register and current processor
priority register are only accessed on the current cpu. In fact the
hypervisor doesn't even let us choose which cpu's registers to access.
The only function to use cpu twice is xics_migrate_irqs_away, not a fast
path. But we can cache the result of get_hard_processor_id() instead of
calling get_hard_smp_processor_id(cpu) in a loop across the call to rtas.
Years ago the irq code passed smp_processor_id into get_irq, I thought
we might initialize the CPPR third party at boot as an extra measure of
saftey, and it made the code symmetric with the qirr (queued interrupt
for software generated interrupts), but now it is just extra and
sometimes unneeded work to pass it down.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This splits the machine definition for celleb into two definitions,
one for celleb_beat, and the other for celleb_native. Though this
looks complex because of sorting some functions, there are no
more semantic changes than that for the splitting.
Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes mmio_nvram_init() callable unconditionally by providing
a dummy definition when CONFIG_MMIO_NVRAM is not defined.
Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implement MSI support for PA Semi PWRficient platforms. MSI is done
through a special range of sources on the openpic controller, and they're
unfortunately breaking the usual concepts of how sources are programmed:
* The source is calculated as 512 + the value written into the MSI
register
* The vector for this source is added to the source and reported
through IACK
This means that for simplicity, it makes much more sense to just set the
vector to 0 for the source, since that's really the vector we expect to
see from IACK.
Also, the affinity/priority registers will affect 16 sources at a
time. To avoid most (simple) users from being limited by this, allocate
16 sources per device but use only one. This means that there's a total
of 32 sources.
If we get usage scenarions that need more sources, the allocator should
probably be revised to take an alignment argument and size, not just do
natural alignment.
Finally, since I'm already touching the MPIC names on pasemi, rename
the base one from the somewhat odd " PAS-OPIC " to "PASEMI-OPIC".
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit fbd568a3e6 ("Change
synchronize_kernel to _rcu and _sched") changed the deprecated
synchronize_kernel() in HvLpEvent_unregisterHandler() to
synchronize_rcu(). It turns out that it should have been
synchronize_sched().
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We're currently getting a warning from not checking the result of
sysfs_create_group, which is declared as __must_check.
This change introduces appropriate error-handling for
spu_add_sysdev_attr_group()
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently, we have a possibilty that the SLBs setup during context
switch don't cover the entirety of the necessary lscsa and code
regions, if these regions cross a segment boundary.
This change checks the start and end of each region, and inserts a SLB
entry for each, if unique. We also remove the assumption that the
spu_save_code and spu_restore_code reside in the same segment, by using
the specific code array for save and restore.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a function spu_64k_pages_available(), so that we can abstract the
explicity use of mmu_psize_defs() in lssca_alloc.c
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that we have a helper function to setup a SPU SLB, use it for
__spu_trap_data_seq.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently, the SPU context switch code (spufs/switch.c) sets up the
SPU's SLBs directly, which requires some low-level mm stuff.
This change moves the kernel SLB setup to spu_base.c, by exposing
a function spu_setup_kernel_slbs() to do this setup. This allows us
to remove the low-level mm code from switch.c, making it possible
to later move switch.c to the spufs module.
Also, add a struct spu_slb for the cases where we need to deal with
SLB entries.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch changes the way we check for the existence of
vicinity property in spe device nodes.
The new implementation does not depend on having an initialized
cbe_spu_info[0].spus, and checks for presence of vicinity in all
nodes, not only in the first one.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Export force_sig_info to allow signals to be sent from a modular spufs.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The pm_interval register in the Cell PMU is read/write, but was implemented in
the kernel as write-only. Previously, the written value was saved in a "shadow"
copy so calls to cbe_read_pm() could return the value.
Perfmon2 needs to be able to read the current values of pm_interval, so change
cbe_read_pm() to read the actual register instead of the "shadow" copy. There
is currently no code in the kernel that tries to read the pm_interval register
with cbe_read_pm() (expecting to receive the "shadow" value), so this should
not break any existing code.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently it's impossible to build a ps3_defconfig which will reboot
without modules installed. This makes it all too easy to find yourself
with a PS3 that won't reboot.
This is because the system manager driver, which provides the reboot
mechanism, is only selectable if PS3_ADVANCED is set, else it defaults
to m. In ps3_defconfig PS3_ADVANCED is not set, therefore the system
manager is built as a module.
It would be desirable IMHO for the defconfig to produce a kernel that
boots and reboots, without needing modules to be installed.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Printk was observed to hang during module unload due to a limited
window of characters that may be sent to the hypervisor. The window
only reexpands when we receive an ack from the HV and the spinlock here
prevents us from ever processing that ack. This fixes it by dropping
the lock before doing the printk, then looping back to the top to
reacquire the lock.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Verified on mpc866ads. This version has muram and brg nodes added to dts
to get the things work.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
The MPC837x MDS is a new member of Freescale MDS reference system.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There was only one global function in vpdinfo.c and it was only called
from pci.c, so merge them and make the function static.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently we hardwire the number of SLBs to 64, but PAPR says we
should use the ibm,slb-size property to obtain the number of SLB
entries. This uses this property instead of assuming 64. If no
property is found, we assume 64 entries as before.
This soft patches the SLB handler, so it shouldn't change performance
at all.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Also remove another unnecessary forward declaration.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It only needs the iommu_table address. It also makes use of the node
name to print error messages. So just pass it the things it needs.
This reduces the places that know about the pci_dn by one.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds support for native CBE on Celleb, that is, without the BEAT
hypervisor. Many codes in platforms/cell/ are used in native CBE
environment.
Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the following link error with CONFIG_PPC_CELL_NATIVE=y and
CONFIG_PPC_CELL_BLADE=n:
arch/powerpc/platforms/built-in.o: In function `.cell_setup_arch':
setup.c:(.init.text+0xe80): undefined reference to `.mmio_nvram_init'
Signed-off-by: Kou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PowerMac and CHRP/BriQ platforms have quirks to switch some IDE
controllers from legacy mode to fully native mode. Those quirks
however will not work properly anymore due to a change to the
generic code to better handle legacy IDE resources.
This fixes it by moving those quirk to "early" quirks (so they
run before resources are probed for the devices) and clearing
all BARs after the conversion to force a reallocation of sane
values.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds checking for NULL returned value from of_get_property to
prevent possible NULL pointer dereference in the case when expected
properties are not present.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Convert #include of asm/of_{platform, device}.h into
linux/of_{platform,device}.h for a few scattered platforms.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix up the module information for gpio-mdio, it wouldn't load
because of lacking license, and wouldn't auto-load because of missing
MODULE_DEVICE_TABLE.
Signed-off-by: Olof Johansson <olof@lixom.net>
arch/powerpc/platforms/iseries/setup.c:111:27: warning: constant 0x100000000 is so big it is long
arch/powerpc/platforms/iseries/setup.c:113:23: warning: constant 0x100000000 is so big it is long
arch/powerpc/platforms/iseries/setup.c:117:27: warning: constant 0x000fffffffffffff is so big it is long
arch/powerpc/platforms/iseries/setup.c:127:28: warning: constant 0x100000000 is so big it is long
arch/powerpc/platforms/iseries/setup.c:129:24: warning: constant 0x100000000 is so big it is long
arch/powerpc/platforms/iseries/setup.c:233:5: warning: constant 0x000fffffffffffff is so big it is long
arch/powerpc/platforms/iseries/setup.c:235:5: warning: constant 0x000fffffffffffff is so big it is long
arch/powerpc/platforms/iseries/setup.c:319:6: warning: symbol 'mschunks_alloc' was not declared. Should it be static?
arch/powerpc/platforms/iseries/setup.c:661:6: warning: symbol 'iSeries_early_setup' was not declared. Should it be static?
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixes sparse warning:
arch/powerpc/platforms/iseries/pci.c:169:13: warning: symbol 'iSeries_pci_final_fixup' was not declared. Should it be static?
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Do not wait for the pci slot status before reporting an error
to the device driver. Some systems may take many seconds to
report the slot status, and this can confuse unsuspecting
device drivers.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If an "empty" slot is failing, make sure its a permanent failure;
else process the error normally.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Perform all error checking at the "partitonable endpoint"
of the device.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/platforms/powermac/time.c:88: warning: 'to_rtc_time' defined but not used
This fixes the warning by making the relevant code depend on the
users.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
prod_processor() is unused, and that's a good thing, since it does not
supply the required proc id parameter to H_PROD.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This cleans up the SMT thread handling, removing some hard coded
assumptions and providing a set of helpers to convert between linux
cpu numbers, thread numbers and cores.
This implementation requires the number of threads per core to be a
power of 2 and identical on all cores in the system, but it's an
implementation detail, not an API requirement and so this limitation
can be lifted in the future if anybody ever needs it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit a2b51812a4.
It turns out that this change caused some machines to fail to come
back up when being rebooted, and generated an error in the hypervisor
error log on some machines. The platform architecture (PAPR) is a
little unclear on exactly when the RTAS ibm,os-term function should be
called. Until that is clarified I'm reverting this commit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use smp_send_stop() to move all cpus besides the one executing reboot
into a hold loop, to keep them from being in powersavings mode at the
time of reboot.
Signed-off-by: Olof Johansson <olof@lixom.net>
When the PWRficient cpus are entered into powersavings states, the
astate is automatically dropped down to 0. While we still restore it
when we come out of idle, it can still cause some weird effects with
respect to performance (especially since it takes a while to ramp up to
higher astates).
So, to avoid this, don't enter power savings when the cpufreq driver
(or user) has set higher astates than 0.
The restore is still required, since there's a chance the astate has
been raised from the other cpu while the idling one was asleep.
Signed-off-by: Olof Johansson <olof@lixom.net>
There will be more product numbers in the future than just PA6T-1682M,
but they will share much of the features. Remove some of the explicit
references and compatibility checks with 1682M, and replace most of them
with the more generic term "PWRficient".
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Misc cleanups of mdio_gpio:
* Better error handling/unrolling in case of init/alloc failures
* Go through child nodes and get their interrupts instead of using
hardcoded values
* Remap the GPIO registers at module load/driver init instead of during probe
* Coding style and other misc cleanups
Signed-off-by: Olof Johansson <olof@lixom.net>
mmc_spi has hit the mainline, so we can start using it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now the rtc class ds1374 driver has been added, remove the old rtc
driver hookup code, add rtc node to device trees, and turn on the
new driver in the defconfigs.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We can currently cause an oops by repeatedly creating and destroying
contexts, while doing getdents() calls on the "/spu" directory.
This is due to the context's top-level dentry remaining hashed while
the context is being destroyed.
Fix this by unhashing the context's dentry with the
dentry->d_inode->i_mutex held. This way, we'll hit the check for
d_unhashed in dentry_readdir, and won't be included in the
list of subdirs for /spu.
test: spufs-testsuite:tests/01-spu_create/07-destroy-vs-readdir-race
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The rtas_os_term() routine was being called at the wrong time.
The actual rtas call "os-term" will not ever return, and so
calling it from the panic notifier is too early. Instead,
call it from the machine_reset() call.
This splits the rtas_os_term() routine into two: one part to capture
the kernel panic message, invoked during the panic notifier, and
another part that is invoked during machine_reset().
Prior to this patch, the os-term call was never being made,
because panic_timeout was always non-zero. Calling os-term
helps keep the hypervisor happy! We have to keep the hypervisor
happy to avoid service, dump and error reporting problems.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If on a rev. 2.1, adjust UCC clock and data timing characteristics
as specified in the rev.2.1 erratum #2.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
currently the board-level PHY reset code for the mpc832x MDS messes with
reset configuration words source settings which is plain wrong (it
looks like this board code was cut-n-pasted from the mpc8360 mds code,
which has the PHY reset bits in a different BCSR); this patch points
the PHY reset code to the proper mpc832x mds PHY reset bits in the BCSR.
Signed-off-by: Peter Van Ackeren <peter.vanackeren@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch does fix potential NULL pointer dereference that could take
place inside of strcmp() if of_get_property() call failed.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Due to an erratum, we don't want to reset the mpic at boot time. It can
sometimes cause problems with lost interrupts later on while running.
Signed-off-by: Olof Johansson <olof@lixom.net>
Olaf Hering
Michael Ellerman
Geoff Levand
Takashi Yamamoto
Geert Uytterhoeven
Kay Sievers
Greg Kroah-Hartman
Paul Mackerras
Jon Loeliger
Grant Likely
Wade Farnsworth
Scott Wood
Timur Tabi
John Rigby
Paul Gortmaker
Anton Vorontsov
Li Yang
Kumar Gala
Marian Balakowicz
Jon Loeliger
Stephen Rothwell
Cyrill Gorcunov
Olof Johansson
Josh Boyer
Michael Neuling
Stephen Neuendorffer
Bob Nelson
Stefan Roese
Valentine Barshak
Benjamin Herrenschmidt
Hugh Blemings
Jeremy Kerr
Andre Detsch
Aegis Lin
Christoph Hellwig
Luke Browning
Masato Noguchi
Arnd Bergmann
Julio M. Merino Vidal
Julia Lawall
Lucas Woods
Milton Miller
Ishizaki Kou
Kevin Corry
joe@perches.com
Linas Vepstas
Johannes Berg
Nathan Lynch
Kim Phillips