Unmapping causes TLB flushing, therefore we should make it in the largest
possible batches. However we shouldn't starve the guest for too long. So if
the guest has space for at least two big packets and we don't have at least a
quarter ring to unmap, delay it for at most 1 milisec.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A malicious or buggy guest can leave its queue filled indefinitely, in which
case qdisc start to queue packets for that VIF. If those packets came from an
another guest, it can block its slots and prevent shutdown. To avoid that, we
make sure the queue is drained in every 10 seconds.
The QDisc queue in worst case takes 3 round to flush usually.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xen network protocol had implicit dependency on MAX_SKB_FRAGS. Netback has to
handle guests sending up to XEN_NETBK_LEGACY_SLOTS_MAX slots. To achieve that:
- create a new skb
- map the leftover slots to its frags (no linear buffer here!)
- chain it to the previous through skb_shinfo(skb)->frag_list
- map them
- copy and coalesce the frags into a brand new one and send it to the stack
- unmap the 2 old skb's pages
It's also introduces new stat counters, which help determine how often the guest
sends a packet with more than MAX_SKB_FRAGS frags.
NOTE: if bisect brought you here, you should apply the series up until
"xen-netback: Timeout packets in RX path", otherwise malicious guests can block
other guests by not releasing their sent packets.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These counters help determine how often the buffers had to be copied. Also
they help find out if packets are leaked, as if "sent != success + fail",
there are probably packets never freed up properly.
NOTE: if bisect brought you here, you should apply the series up until
"xen-netback: Timeout packets in RX path", otherwise Windows guests can't work
properly and malicious guests can block other guests by not releasing their sent
packets.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These became obsolete with grant mapping. I've left intentionally the
indentations in this way, to improve readability of previous patches.
NOTE: if bisect brought you here, you should apply the series up until
"xen-netback: Timeout packets in RX path", otherwise Windows guests can't work
properly and malicious guests can block other guests by not releasing their sent
packets.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces grant mapping on netback TX path. It replaces grant copy
operations, ditching grant copy coalescing along the way. Another solution for
copy coalescing is introduced in "xen-netback: Handle guests with too many
frags", older guests and Windows can broke before that patch applies.
There is a callback (xenvif_zerocopy_callback) from core stack to release the
slots back to the guests when kfree_skb or skb_orphan_frags called. It feeds a
separate dealloc thread, as scheduling NAPI instance from there is inefficient,
therefore we can't do dealloc from the instance.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX path need to know if the SKB fragments are stored on pages from another
domain.
Logically this patch should be after introducing the grant mapping itself, as
it makes sense only after that. But to keep bisectability, I moved it here. It
shouldn't change any functionality here. xenvif_zerocopy_callback and
ubuf_to_vif are just stubs here, they will be introduced properly later on.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains a few bits of refactoring before introducing the grant
mapping changes:
- introducing xenvif_tx_pending_slots_available(), as this is used several
times, and will be used more often
- rename the thread to vifX.Y-guest-rx, to signify it does RX work from the
guest point of view
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Storing the pending_idx at the first byte of the linear buffer never looked
good, skb->cb is a more proper place for this. It also prevents the header to
be directly grant copied there, and we don't have the pending_idx after we
copied the header here, so it's time to change it.
It also introduces helpers for the RX side
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to orphan skb in l2tp.
This breaks things like per socket memory limits, TCP Small queues...
Fix this before more people copy/paste it.
This is very similar to commit 8f646c922d
("vxlan: keep original skb ownership")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Usage of skb->tstamp should remain private to TCP stack
(only set on packets on write queue, not on cloned ones)
Otherwise, packets given to loopback interface with a non null tstamp
can confuse netif_rx() / net_timestamp_check()
Other possibility would be to clear tstamp in loopback_xmit(),
as done in skb_scrub_packet()
Fixes: 740b0f1841 ("tcp: switch rtt estimations to usec resolution")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a fixup patch to resolve issues with const from my earlier patch.
Make all the setter functions use const on input parameter.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
htb_dump() and htb_dump_class() do not strictly need to acquire
qdisc lock to fetch qdisc and/or class parameters.
We hold RTNL and no changes can occur.
This reduces by 50% qdisc lock pressure while doing tc qdisc|class dump
operations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring says:
====================
6lowpan: header cleanup
this patch series fix a missing include of 6LoWPAN header and move it
into the include/net directory. Since we did some code sharing with
bluetooth 6LoWPAN the header turns into a generic header for 6LoWPAN.
Instead to use a relative path in bluetooth 6LoWPAN we can now use
include <net/6lowpan.h>.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This header is used by bluetooth and ieee802154 branch. This patch
move this header to the include/net directory to avoid a use of a
relative path in include.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6lowpan.h file contains some static inline function which use
internal ipv6 api structs. Add a include of ipv6.h to be sure that it's
known before.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix static error introduced by commit:
b97b33a3df [645/653] net/mlx4_en: Verify
mlx4_en module parameters
sparse warnings:
drivers/net/ethernet/mellanox/mlx4/en_main.c:335:6: sparse: symbol
'mlx4_en_verify_params' was not declared. Should it be static?
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make local functions static (ie. only used in bond_options.c)
Make bond options parsing tables constant.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are defined but no longer used.
Compile tested only.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Can be invoked from non-BH context.
Based upon a patch by Eric Dumazet.
Fixes: f19c29e3e3 ("tcp: snmp stats for Fast Open, SYN rtx, and data pkts")
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we're using GFP_KERNEL, however there are some path(s) where we
can hold some spinlocks, specifically bond->curr_slave_lock:
[ 4.722916] BUG: sleeping function called from invalid context at mm/slub.c:965
[ 4.724438] in_atomic(): 1, irqs_disabled(): 0, pid: 940, name: ifup-eth
[ 4.726034] 5 locks held by ifup-eth/940:
...snip...
[ 4.734646] #4: (&bond->curr_slave_lock){+...+.}, at: [<ffffffffa00badc6>] bond_enslave+0xda6/0xdd0 [bonding]
...snip...
[ 4.759081] [<ffffffffa00b6f11>] bond_change_active_slave+0x191/0x3b0 [bonding]
[ 4.760917] [<ffffffffa00b7227>] bond_select_active_slave+0xf7/0x1d0 [bonding]
[ 4.762751] [<ffffffffa00badce>] bond_enslave+0xdae/0xdd0 [bonding]
...snip...
As it's out of hot path and is a really rare event - change the gfp_t flags
to GFP_ATOMIC to avoid sleeping under spinlock.
v2: convert new notify calls to GFP_ATOMIC.
CC: Thomas Glanzmann <thomas@glanzmann.de>
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e688a60480 ("net: introduce DST_NOPEER dst flag") introduced
DST_NOPEER because because of crashes in ipv6_select_ident called from
udp6_ufo_fragment.
Since commit 916e4cf46d ("ipv6: reuse ip6_frag_id from
ip6_ufo_append_data") we don't call ipv6_select_ident any more from
ip6_ufo_append_data, thus this flag lost its purpose and can be removed.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang says:
====================
r8152: cleanups
Deal with some empty lines and spaces, replace some tp->netdev with netdev,
and remove the unnecessary function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The rtl8152_get_stats() returns the point address of the struct
net_device_stats. This could be got from struct net_device directly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add or remove some empty lines. Replace the spaces with the tabs.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes some whitespace issues in Kconfig files of IEEE
802.15.4 subsytem.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 8fad346f36
(ieee802154: add basic support for RF212 to at86rf230 driver)
we support at86rf212 as well.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently maps a page for DMA, divides the page into multiple
frags and posts them to the HW. It un-maps the page after data is received
on all the frags of the page. This scheme doesn't work when bounce buffers
are used for DMA (swiotlb=force kernel param).
This patch fixes this problem by calling dma_sync_single_for_cpu() for each
frag (excepting the last one) so that the data is copied from the bounce
buffers. The page is un-mapped only when DMA finishes on the last frag of
the page.
(Thanks Ben H. for suggesting the dma_sync API!)
This patch also renames the "last_page_user" field of be_rx_page_info{}
struct to "last_frag" to improve readability of the fixed code.
Reported-by: Li Fengmao <li.fengmao@zte.com.cn>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Wunderlich says:
====================
this series contains a header file proposal for MPLS labels. These
labels do not seem to be properly defined in the kernel so far. We are
developing a wired/wireless 802.21/MPLS switch and need to check the
MPLS labels to use the traffic control info for transmissions over
802.11 networks.
Changes to third version:
* rename mpls_label_stack to mpls_label (thanks Neil)
* fix over-indendented closing brac (thanks Sergei)
* add Johannes' Ack
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
MPLS labels may contain traffic control information, which should be
evaluated and used by the wireless subsystem if present.
Also check for IEEE 802.21 which is always network control traffic.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Labels for the Multiprotocol Label Switching are defined in RFC 3032
which was superseded by RFC 5462. Add the definition to UAPI and a stub
header for include/linux.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the Ethertype for IEEE Std 802.21 - Media Independent Handover
Protocol. This Ethertype is used for network control messages.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix memory leak in ieee80211_prep_connection(), sta_info leaked on
error. From Eytan Lifshitz.
2) Unintentional switch case fallthrough in nft_reject_inet_eval(),
from Patrick McHardy.
3) Must check if payload lenth is a power of 2 in
nft_payload_select_ops(), from Nikolay Aleksandrov.
4) Fix mis-checksumming in xen-netfront driver, ip_hdr() is not in the
correct place when we invoke skb_checksum_setup(). From Wei Liu.
5) TUN driver should not advertise HW vlan offload features in
vlan_features. Fix from Fernando Luis Vazquez Cao.
6) IPV6_VTI needs to select NET_IPV_TUNNEL to avoid build errors, fix
from Steffen Klassert.
7) Add missing locking in xfrm_migrade_state_find(), we must hold the
per-namespace xfrm_state_lock while traversing the lists. Fix from
Steffen Klassert.
8) Missing locking in ath9k driver, access to tid->sched must be done
under ath_txq_lock(). Fix from Stanislaw Gruszka.
9) Fix two bugs in TCP fastopen. First respect the size argument given
to tcp_sendmsg() in the fastopen path, and secondly prevent
tcp_send_syn_data() from potentially using order-5 allocations.
From Eric Dumazet.
10) Fix handling of default neigh garbage collection params, from Jiri
Pirko.
11) Fix cwnd bloat and over-inflation of RTT when transmit segmentation
is in use. From Eric Dumazet.
12) Missing initialization of Realtek r8169 driver's statistics
seqlocks. Fix from Kyle McMartin.
13) Fix RTNL assertion failures in 802.3ad and AB ARP monitor of bonding
driver, from Ding Tianhong.
14) Bonding slave release race can cause divide by zero, fix from
Nikolay Aleksandrov.
15) Overzealous return from neigh_periodic_work() causes reachability
time to not be computed. Fix from Duain Jiong.
16) Fix regression in ipv6_find_hdr(), it should not return -ENOENT when
a specific target is specified and found. From Hans Schillstrom.
17) Fix VLAN tag stripping regression in BNA driver, from Ivan Vecera.
18) Tail loss probe can calculate bogus RTTs due to missing packet
marking on retransmit. Fix from Yuchung Cheng.
19) We cannot do skb_dst_drop() in iptunnel_pull_header() because
multicast loopback detection in later code paths need access to
skb_rtable(). Fix from Xin Long.
20) The macvlan driver regresses in that it propagates lower device
offload support disables into itself, causing severe slowdowns when
running over a bridge. Provide the software offloads always on
macvlan devices to deal with this and the regression is gone. From
Vlad Yasevich.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (103 commits)
macvlan: Add support for 'always_on' offload features
net: sctp: fix sctp_sf_do_5_1D_ce to verify if we/peer is AUTH capable
ip_tunnel:multicast process cause panic due to skb->_skb_refdst NULL pointer
net: cpsw: fix cpdma rx descriptor leak on down interface
be2net: isolate TX workarounds not applicable to Skyhawk-R
be2net: Fix skb double free in be_xmit_wrokarounds() failure path
be2net: clear promiscuous bits in adapter->flags while disabling promiscuous mode
be2net: Fix to reset transparent vlan tagging
qlcnic: dcb: a couple off by one bugs
tcp: fix bogus RTT on special retransmission
hsr: off by one sanity check in hsr_register_frame_in()
can: remove CAN FD compatibility for CAN 2.0 sockets
can: flexcan: factor out soft reset into seperate funtion
can: flexcan: flexcan_remove(): add missing netif_napi_del()
can: flexcan: fix transition from and to freeze mode in chip_{,un}freeze
can: flexcan: factor out transceiver {en,dis}able into seperate functions
can: flexcan: fix transition from and to low power mode in chip_{en,dis}able
can: flexcan: flexcan_open(): fix error path if flexcan_chip_start() fails
can: flexcan: fix shutdown: first disable chip, then all interrupts
USB AX88179/178A: Support D-Link DUB-1312
...
A couple of fixes here which ensure that regulators using the core
support for GPIO enables work in all cases by ensuring that helpers are
used consistently rather than open coding in places and hence not having
GPIO support in some of them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Vx3C
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of fixes here which ensure that regulators using the core
support for GPIO enables work in all cases by ensuring that helpers
are used consistently rather than open coding in places and hence not
having GPIO support in some of them"
* tag 'regulator-v3.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: Replace direct ops->disable usage
regulator: core: Replace direct ops->enable usage
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton akpm@linux-foundation.org>:
mm: page_alloc: exempt GFP_THISNODE allocations from zone fairness
mm: numa: bugfix for LAST_CPUPID_NOT_IN_PAGE_FLAGS
MAINTAINERS: add and correct types of some "T:" entries
MAINTAINERS: use tab for separator
rapidio/tsi721: fix tasklet termination in dma channel release
hfsplus: fix remount issue
zram: avoid null access when fail to alloc meta
sh: prefix sh-specific "CCR" and "CCR2" by "SH_"
ocfs2: fix quota file corruption
drivers/rtc/rtc-s3c.c: fix incorrect way of save/restore of S3C2410_TICNT for TYPE_S3C64XX
kallsyms: fix absolute addresses for kASLR
scripts/gen_initramfs_list.sh: fix flags for initramfs LZ4 compression
mm: include VM_MIXEDMAP flag in the VM_SPECIAL list to avoid m(un)locking
memcg: reparent charges of children before processing parent
memcg: fix endless loop in __mem_cgroup_iter_next()
lib/radix-tree.c: swapoff tmpfs radix_tree: remember to rcu_read_unlock
dma debug: account for cachelines and read-only mappings in overlap tracking
mm: close PageTail race
MAINTAINERS: EDAC: add Mauro and Borislav as interim patch collectors
Jan Stancek reports manual page migration encountering allocation
failures after some pages when there is still plenty of memory free, and
bisected the problem down to commit 81c0a2bb51 ("mm: page_alloc: fair
zone allocator policy").
The problem is that GFP_THISNODE obeys the zone fairness allocation
batches on one hand, but doesn't reset them and wake kswapd on the other
hand. After a few of those allocations, the batches are exhausted and
the allocations fail.
Fixing this means either having GFP_THISNODE wake up kswapd, or
GFP_THISNODE not participating in zone fairness at all. The latter
seems safer as an acute bugfix, we can clean up later.
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: <stable@kernel.org> [3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When doing some numa tests on powerpc, I triggered an oops bug. I find
it is caused by using page->_last_cpupid. It should be initialized as
"-1 & LAST_CPUPID_MASK", but not "-1". Otherwise, in task_numa_fault(),
we will miss the checking (last_cpupid == (-1 & LAST_CPUPID_MASK)). And
finally cause an oops bug in task_numa_group(), since the online cpu is
less than possible cpu. This happen with CONFIG_SPARSE_VMEMMAP disabled
Call trace:
SMP NR_CPUS=64 NUMA PowerNV
Modules linked in:
CPU: 24 PID: 804 Comm: systemd-udevd Not tainted3.13.0-rc1+ #32
task: c000001e2746aa80 ti: c000001e32c50000 task.ti:c000001e32c50000
REGS: c000001e32c53510 TRAP: 0300 Not tainted(3.13.0-rc1+)
MSR: 9000000000009032 <SF,HV,EE,ME,IR,DR,RI> CR:28024424 XER: 20000000
CFAR: c000000000009324 DAR: 7265717569726857 DSISR:40000000 SOFTE: 1
NIP .task_numa_fault+0x1470/0x2370
LR .task_numa_fault+0x1468/0x2370
Call Trace:
.task_numa_fault+0x1468/0x2370 (unreliable)
.do_numa_page+0x480/0x4a0
.handle_mm_fault+0x4ec/0xc90
.do_page_fault+0x3a8/0x890
handle_page_fault+0x10/0x30
Instruction dump:
3c82fefb 3884b138 48d9cff1 60000000 48000574 3c62fefb3863af78 3c82fefb
3884b138 48d9cfd5 60000000 e93f0100 <812902e4> 7d2907b45529063e 7d2a07b4
---[ end trace 15f2510da5ae07cf ]---
Signed-off-by: Liu Ping Fan <pingfank@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tree location entries should start with the appropriate type.
Add git to some, hg to another.
Neaten tree type description.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert whitespace to single tab for separators.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is a modification of the patch originally proposed by
Xiaotian Feng <xtfeng@gmail.com>: https://lkml.org/lkml/2012/11/5/413
This new version disables DMA channel interrupts and ensures that the
tasklet wil not be scheduled again before calling tasklet_kill().
Unfortunately the updated patch was not released at that time due to
planned rework of Tsi721 mport driver to use threaded interrupts (which
has yet to happen). Recently the issue was reported again:
https://lkml.org/lkml/2014/2/19/762.
Description from the original Xiaotian's patch:
"Some drivers use tasklet_disable in device remove/release process,
tasklet_disable will inc tasklet->count and return. If the tasklet is
not handled yet under some softirq pressure, the tasklet will be
placed on the tasklet_vec, never have a chance to be excuted. This
might lead to a heavy loaded ksoftirqd, wakeup with pending_softirq,
but tasklet is disabled. tasklet_kill should be used in this case."
This patch is applicable to kernel versions starting from v3.5.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Xiaotian Feng <xtfeng@gmail.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Galbraith <bitbucket@online.de>
Cc: <stable@vger.kernel.org> [3.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Current implementation of HFS+ driver has small issue with remount
option. Namely, for example, you are unable to remount from RO mode
into RW mode by means of command "mount -o remount,rw /dev/loop0
/mnt/hfsplus". Trying to execute sequence of commands results in an
error message:
mount /dev/loop0 /mnt/hfsplus
mount -o remount,ro /dev/loop0 /mnt/hfsplus
mount -o remount,rw /dev/loop0 /mnt/hfsplus
mount: you must specify the filesystem type
mount -t hfsplus -o remount,rw /dev/loop0 /mnt/hfsplus
mount: /mnt/hfsplus not mounted or bad option
The reason of such issue is failure of mount syscall:
mount("/dev/loop0", "/mnt/hfsplus", 0x2282a60, MS_MGC_VAL|MS_REMOUNT, NULL) = -1 EINVAL (Invalid argument)
Namely, hfsplus_parse_options_remount() method receives empty "input"
argument and return false in such case. As a result, hfsplus_remount()
returns -EINVAL error code.
This patch fixes the issue by means of return true for the case of empty
"input" argument in hfsplus_parse_options_remount() method.
Signed-off-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
zram_meta_alloc could fail so caller should check it. Otherwise, your
system will hang.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit bcf24e1daa ("mmc: omap_hsmmc: use the generic config for
omap2plus devices"), enabled the build for other platforms for compile
testing.
sh-allmodconfig now fails with:
include/linux/omap-dma.h:171:8: error: expected identifier before numeric constant
make[4]: *** [drivers/mmc/host/omap_hsmmc.o] Error 1
This happens because SuperH #defines "CCR", which is one of the enum
values in include/linux/omap-dma.h. There's a similar issue with "CCR2"
on sh2a.
As "CCR" and "CCR2" are too generic names for global #defines, prefix
them with "SH_" to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Global quota files are accessed from different nodes. Thus we cannot
cache offset of quota structure in the quota file after we drop our node
reference count to it because after that moment quota structure may be
freed and reallocated elsewhere by a different node resulting in
corruption of quota file.
Fix the problem by clearing dq_off when we are releasing dquot structure.
We also remove the DB_READ_B handling because it is useless -
DQ_ACTIVE_B is set iff DQ_READ_B is set.
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Goldwyn Rodrigues <rgoldwyn@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On exynos5250, exynos5420 and exynos5260 it was observed that, after 1
cycle of S2R, the rtc-tick occurs at a very fast rate as compared to the
rtc-tick occuring before S2R.
This patch fixes the above issue by correcting the wrong way of
save/restore of S3C2410_TICNT for TYPE_S3C64XX.
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently symbols that are absolute addresses are incorrectly displayed
in /proc/kallsyms if the kernel is loaded with kASLR.
The problem was that the scripts/kallsyms.c file which generates the
array of symbol names and addresses uses an relocatable value for all
symbols, even absolute symbols. This patch fixes that.
Several kallsyms output in different boot states for comparison:
$ egrep '_(stext|_per_cpu_(start|end))' /root/kallsyms.nokaslr
0000000000000000 D __per_cpu_start
0000000000014280 D __per_cpu_end
ffffffff810001c8 T _stext
$ egrep '_(stext|_per_cpu_(start|end))' /root/kallsyms.kaslr1
000000001f200000 D __per_cpu_start
000000001f214280 D __per_cpu_end
ffffffffa02001c8 T _stext
$ egrep '_(stext|_per_cpu_(start|end))' /root/kallsyms.kaslr2
000000000d400000 D __per_cpu_start
000000000d414280 D __per_cpu_end
ffffffff8e4001c8 T _stext
$ egrep '_(stext|_per_cpu_(start|end))' /root/kallsyms.kaslr-fixed
0000000000000000 D __per_cpu_start
0000000000014280 D __per_cpu_end
ffffffffadc001c8 T _stext
Signed-off-by: Andy Honig <ahonig@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LZ4 as implemented in the kernel differs from the default method now
used by the reference implementation of LZ4. Until the in-kernel method
is updated to support the new default, passing the legacy flag (-l) to
the compressor is necessary. Without this flag the kernel-generated,
LZ4-compressed initramfs is junk.
Kyungsik said:
: It seems that lz4 supports legacy format with the same option as lz4c
: does. Just looking at the first few bytes of lz4 compressed image, we can
: see whether it is new format or not.
:
: It shows new format magic number without this patch. New format magic
: number is 0x184d2204.
:
: $ hexdump -C ./initramfs_data.cpio.lz4 |more
: 00000000 04 22 4d 18 64 70 b9 69 (Little Endian)
: ...
:
: Currently kernel supports legacy format only.
Signed-off-by: Daniel M. Weeks <dan@danweeks.net>
Cc: Michal Marek <mmarek@suse.cz>
Acked-by: Kyungsik Lee <kyungsik.lee@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zoltan Kiss
Eric Dumazet
stephen hemminger
David S. Miller
Alexander Aring
Ivan Vecera
Fengguang Wu
Veaceslav Falico
Hannes Frederic Sowa
hayeswang
Sathya Perla
Simon Wunderlich
Linus Torvalds
Johannes Weiner
Liu Ping Fan
Joe Perches
Alexandre Bounine
Vyacheslav Dubeyko
Minchan Kim
Geert Uytterhoeven
Jan Kara
Vikas Sajjan
Andy Honig
Daniel M. Weeks