25165f79ad
("ASoC: rsnd: enable clock-frequency for both 44.1kHz/48kHz")
supports both 44.1kHz/48kHz clock-frequency settings for ADG
which will be used for AUDIO_OLKOUTn.
But some board doesn't need it, thus, it is not mandatory.
But, above patch didn't care about the case of "clock-frequency" DT
property was not present.
This patch ignores ADG settings if AUDIO_OLKOUTn was not used.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
[Kuninori: tidyup not to break non AUDIO_OLKOUTn case]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current clock-frequency allows only 1 clock, but ADG can
handle both 44.1kHz/48kHz base clocks. This patch enables these.
On Salvator-X board, AUDIO_CLKOUT which is generated by ADG
is connected to ak4613 MCKI, and it should be synchronized with
LRCK. Thus, we need both 44.1kHz/48kHz base clock-frequency.
Otherwise, either one sounds strange in high frequency sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_mod_make_sure() will be used any situation,
thus, under DEBUG is not realistic.
This patch move it to non DEBUG area
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using rsnd_kctrl_new_m/s/e function,
but the differences are very few.
This patch merge these rsnd_kctrl_new_m/s/e into rsnd_kctrl_new
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current src->convert_rate will be set on .hw_param, and
be reset on .quit timing.
But, .hw_param will not be called again if user did Ctrl-Z + fg.
It should be reset on initial of .hw_param to keep its value.
Here, ctu.c already do this.
This patch solves this issue, other wise, MIXed sound will be
strange if user did like below.
> aplay -D plughw:0,0 sound_44100.wav &
> aplay -D plughw:0,1 sound_96000.wav
> Ctrl-Z
> fg # 96kHz will be played as 44.1kHz
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
adg is calling of_clk_add_provider() when probe time,
thus, remove should call of_clk_del_provider(), it doesn't now.
This patch fix this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current adg is calling of_clk_add_povider() multiple times,
but it is not correct usage. This patch fixup its parameter
and call it once.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rcar driver is trying to remove kctrl when remove time.
But, 1) rcar driver can't/shouldn't remove before removing sound
card driver, 2) sound card driver will call snd_ctl_dev_free()
and removes all kctrls by snd_ctl_remove().
Thus, rsnd_kctrl_remove() is not necessary. Current implementation
will get Oops when removing rcar driver after sound card.
This patch fix this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car Datasheet is indicating "SSICR.CKDV = 000 is invalid when
SSIWSR.WS_MODE = 1 or SSIWSR.CONT = 1".
Current driver will set CONT, thus, we shouldn't use CKDV = 000.
This patch fixup it.
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 2a3af642eb20("ASoC: rcar: clear DE bit only in PDMACHCR...")
added rsnd_dmapp_bset(), but it used copy-paste. Thus, it had
unnecessary "volatile", and had below warning on x86.
This patch fix it.
sound/soc/sh/rcar/dma.c: In function 'rsnd_dmapp_bset':
>> sound/soc/sh/rcar/dma.c:463:21: warning: passing argument 1 of \
'ioread32' discards 'volatile' qualifier from pointer target \
type [-Wdiscarded-qualifiers]
u32 val = ioread32(addr);
^~~~
In file included from arch/x86/include/asm/io.h:203:0,
from arch/x86/include/asm/realmode.h:5,
from arch/x86/include/asm/acpi.h:33,
from arch/x86/include/asm/fixmap.h:19,
from arch/x86/include/asm/apic.h:10,
from arch/x86/include/asm/smp.h:12,
from include/linux/smp.h:59,
from include/linux/topology.h:33,
from include/linux/gfp.h:8,
from include/linux/idr.h:16,
from include/linux/kernfs.h:14,
from include/linux/sysfs.h:15,
from include/linux/kobject.h:21,
from include/linux/of.h:21,
from include/linux/of_dma.h:16,
from sound/soc/sh/rcar/dma.c:12:
include/asm-generic/iomap.h:31:21: note: expected 'void *' \
but argument is of type 'volatile void *'
extern unsigned int ioread32(void __iomem *);
^~~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car datasheet indicates "Clear DE in PDMACHCR" for transfer stop,
but current code clears all bits in PDMACHCR.
Because of this, DE bit might never been cleared,
and it causes CMD overflow. This patch fixes this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the problem that the missing value of the route path
setting table and incorrect values are set in the CMD_ROUTE_SELECT
register.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
[Kuninori: shared data on MIX and non-MIX case]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI8 is is sharing pin with SSI7, and nothing to do for SSI_MODEx.
It is special pin and it needs special settings whole system,
but we can't confirm it, because we never have SSI8 available board.
This patch fixup SSI_MODEx settings error for SSI8 on connection test,
but should be confirmed behavior on real board in the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, this function cannot fail for the ADG case. Still, let's
apply defensive programming techniques to make sure we fail gracefully
whenever rsnd_mod_init() gets extended with another failure case.
Reported by Coverity (CID 1397893).
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Coverity reported (CID 1397992) this self-assignment. I think the code
stays readable even with the assignments removed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sync convert rate settings should be availabled *after* Playing.
Thus, src->sync should be reset first of init function.
Otherwise, it will set remaining settings when it start playing.
This patch fixes it. Thanks to Yokoyama-san
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 5f222a292 ("ASoC: rsnd: use for_each_rsnd_mod_xxx() ...")
modifies rsnd_dai_call() to use for_each_rsnd_mod_arrays().
Current rsnd is incrementing iterator in rsnd_mod_next(),
but the iterator will indicate +1 position in for_each loop in
this case. Incremental position should be inside for()
Reported-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 5f222a292 ("ASoC: rsnd: use for_each_rsnd_mod_xxx() ...")
modifies rsnd_dai_call() to use for_each_rsnd_mod_arrays().
Current rsnd is incrementing iterator in rsnd_mod_next(),
but the iterator will indicate +1 position in for_each loop in
this case. Incremental position should be inside for()
Reported-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On an error, snd_ctl_add already free's kctrl, so calling snd_ctl_free_one
to free it again leads to a double free error. Fix this by removing
the extraneous snd_ctl_free_one call.
Issue found using static analysis with CoverityScan, CID 1372908
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver setups BRGCKR/BRRA/BRRB when .probe timing.
But it breaks sound after Suspend/Resume. These should be setups
every start timing.
This patch is tested on R-Car Gen3 Salvator-X board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver enables ADG clock when .probe timing,
but it breaks sound after Suspend/Resume. These should be setups
every suspend/resume timing too.
This patch is tested on R-Car Gen3 Salvator-X board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ssi->usrcnt will be updated on snd_soc_dai_ops::trigger,
but snd_pcm_ops::hw_params will be called *before* it.
Thus, ssi->usrcnt is still 0 when 1st call.
rsnd_ssi_hw_params() needs to check its called count, this means
trigger should be if (ssi->usrcnt) instead of if (ssi->usrcnt > 1).
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSIU was controlled by SSI before, but
commit c7f69ab53("ASoC: rsnd: use mod base common method on SSIU")
separated it into ssiu.c
But, it didn't care about rsnd_get_dalign() for judging SSI_BUSIF_DALIGN
register value which changes the stream data order.
This function will be called from cmd/src/ssiu now, but current code
still cares ssi, not ssiu.
This patch fix it up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
IOMMU needs DMA mapping function to use it. One solution is that
we can use DMA mapped dev on snd_pcm_lib_preallocate_pages_for_all()
for SNDRV_DMA_TYPE_DEV. But pcm_new and dma map timing are mismatched.
Thus, this patch uses SNDRV_DMA_TYPE_CONTINUOUS for pcm_new,
and use dma_sync_single_for_xxx() for each transfer.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas Sound driver requests DMA channel when .probe timing,
and release it when .remove timing. And use DMA on .start/.stop
But, Audio DMAC power ON was handled when request timing (= .probe),
and power OFF was when release timing (= .remove).
This means Audio DMAC power is always ON during driver was enabled.
The best choice to solve this issue is that DMAEngine side handle
this. But current DMAEngine API design can't solve atmic/non-atmic
context issue for power ON/OFF. So next better choice is sound
driver request/release DMA channel each time. This patch do it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current register name of "SSICKR" was came from R-Car Gen1
which is very old style. It is called as "BRGCKR" on R-Car Gen2/Gen3.
Let's rename it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SRC (= Sampling Rate Converter) is supporting
SYNC mode and ASYNC mode. Current src.c cares SRC if FIN != FOUT.
Here, SYNC mode will be used for tweak, so it will be used
even FIN = FOUT. This patch enables SRC sync in such situation
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Tested-by: Yuichi Takagi <yuichi.takagi.uh@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound SSIU has SSI_SYS_STATUS register whick will
be changed if over/under run was occurred.
Current rsnd driver is handling over/under run error on SSI/SRC,
but doesn't on SSIU.
HW guys can't guarantee correct behavior if it already had error bit
on status register when it start.
Thus, it should be cleared every start timing. This patch do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SCU_SYS_STATUSx is the register that writing 1 initializes the bit,
and writing 0 is ignored. So, it should use rsnd_mod_write()
instead of rsnd_mod_bset(), otherwise all bit will be cleared.
Thanks Shimoda-san
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car Gen1 didn't have SSIU IP, and it was part of SRU.
In Gen2, SSIU was created and it has original register.
Let's cleanup rsnd_reg for SSIU, because this driver
doesn't support Gen1 SRU any more.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Gen1 support had been removed. "Gen2 only" comment is
no longer needed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound driver is completely depends on CONFIG_OF
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas Sound driver requests DMA channel when .probe timing,
and release it when .remove timing. And use DMA on .start/.stop
But, Audio DMAC power ON was handled when request timing (= .probe),
and power OFF was when release timing (= .remove).
This means Audio DMAC power is always ON during driver was enabled.
To fixup this issue, it should request/release DMA channel on each
playback/recorde timing.
But, DMA channel request/release function uses mutex lock inside.
This means it will breaks current spinlock's interrupt protect.
To solve this issue, DMA channel request/release function needs to
be called from non-spinlock area. This patch adds its callback.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_dmaen_start() is calling of_node_put() for np,
but it is not needed if it goes through this loop.
This patch tidyup it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA mod is now connected to stream via rsnd_dai_connect().
This means DMA mod can use .remove for its clearance.
rsnd_dma_detach() is no longer needed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI will use DMA mode, and migh be fallback to PIO mode.
Using devm_request_irq() makes its operation more complex when
it fallbacks to PIO mode.
Let's use manual request_irq()/free_irq()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas Sound driver is based on DeviceTree, and no one is
using this driver from non DT. Non-DT support is no longer needed.
Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now, we have for_each_rsnd_mod(), let's use it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using too complex macro for for-loop of each mod.
rsnd_dai_call() is especially defined as very complex macro.
It is easier to read just a little bit by using for_each_rsnd_mod_xxx()
and new rsnd_status_update()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using too complex macro for for-loop of each mod.
In order to simplify this issue, this patch adds new rsnd_mod_next()
which is non-macro.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 1a5658c213 ("ASoC: rsnd: count .probe/.remove for
rsnd_mod_call()") solved multi-resource-free issue, by putting
.probe/.remove under count control. But,it breaks sound mixing case
(if it was used under DPCM). In such case, it uses MIXn/DVCn/SSIn,
and these should be always probed.
This patch reverted above patch, and solved the same issue by
modifing _rsnd_kctrl_remove() function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Marek Vasut
kbuild test robot
Kuninori Morimoto
Mark Brown
Hiroyuki Yokoyama
Wolfram Sang
Colin Ian King