Граф коммитов

141 Коммитов

Автор SHA1 Сообщение Дата
Al Viro f7f4f4dd69 cramfs: take headers to fs/cramfs
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2014-01-25 03:13:02 -05:00
Steven Miao 24a70cf2b2 blackfin: scb: Add system crossbar init code.
If SCB exists in select blackfin cpu, developer can change the SCB
priority in kernel configuration.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>
2013-09-13 10:42:27 +08:00
Paul Gortmaker 13dff62d80 blackfin: delete __cpuinit usage from all blackfin files
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications.  For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.

After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out.  Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.

Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit  -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings.  In any case, they are temporary and harmless.

This removes all the arch/blackfin uses of the __cpuinit macros from
all C files.  Currently blackfin does not have any __CPUINIT used in
assembly files.

[1] https://lkml.org/lkml/2013/5/20/589

Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Bob Liu <lliubbo@gmail.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: uclinux-dist-devel@blackfin.uclinux.org
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2013-07-14 19:36:53 -04:00
James Cosin 352030530c blackfin: fix bootup core clock and system clock display
From: James Cosin <jkosin@intcomgrp.com>

fixes the number of digits to 6 after the decimal point to regain the
significant 0s in the frequency after the decimal point.

Signed-off-by: Steven Miao <realmz6@gmail.com>
2013-05-09 13:03:32 +08:00
Geert Uytterhoeven 363737d664 mtd/uclinux: Use generic __bss_stop instead of _ebss
The standard (see BSS_SECTION() in <asm-generic/vmlinux.lds.h> and
<asm-generic/sections.h>) symbol for the end of BSS is __bss_stop.
This allows to remove all local declarations that have been added to
several architectures just to please CONFIG_MTD_UCLINUX.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Greg Ungerer <gerg@uclinux.org>
2012-06-27 09:59:43 +02:00
Steven Miao 672552adb3 blackfin: fix build after add bf60x mach/pm.h
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
2012-05-21 14:55:07 +08:00
Sonic Zhang 8bf7135fff blackfin: bf60x: Rename the DDR controller macro
Rename the DDR controller macro from DDR0 to DMC0 to avoid confustion for
bf60x.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
2012-05-21 14:54:57 +08:00
Sonic Zhang 1d3dbda6ed blackfin: bf60x: cleanup get clock code
Remove redundance code for get clock.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
2012-05-21 14:54:53 +08:00
Bob Liu 7c141c1c5c blackfin: bf60x: make clock changeable in kernel menuconfig
Add clock changeable support in kernel menuconfig for bf60x.

Signed-off-by: Bob Liu <lliubbo@gmail.com>
2012-05-21 14:54:49 +08:00
Mike Frysinger 592b8785b9 Blackfin: fix unused clk var warning
This is only used on BF60x code (so this patch should get squashed into
the original one that added it).

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
2012-05-21 14:54:37 +08:00
Bob Liu b5affb0147 blackfin: add bf60x to current framework
This patch added bf60x to current blackfin kernel framework.

Signed-off-by: Bob Liu <lliubbo@gmail.com>
2012-05-21 14:54:12 +08:00
Al Viro 39429c5e4a new helper: ext2_image_size()
... implemented that way since the next commit will leave it
almost alone in ext2_fs.h - most of the file (including
struct ext2_super_block) is going to move to fs/ext2/ext2.h.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2012-03-31 16:03:16 -04:00
David Howells 3bed8d6746 Disintegrate asm/system.h for Blackfin [ver #2]
Disintegrate asm/system.h for Blackfin.

Signed-off-by: David Howells <dhowells@redhat.com>
cc: uclinux-dist-devel@blackfin.uclinux.org
Signed-off-by: Bob Liu <lliubbo@gmail.com>
2012-03-21 11:00:08 +08:00
Steven Miao 4dbeccdf7b bf54x: get mem size: missing break in switch
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
2012-01-09 10:26:15 +08:00
Mike Frysinger fb1d9be596 Blackfin: optimize double fault boot checking
This moves the double fault data used at boot time into a single struct
which can then easily be addressed with indexed loads rather than having
to explicitly load multiple addresses.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-07-23 01:10:43 -04:00
KOSAKI Motohiro fecedc8071 Blackfin: convert old cpumask API to new one
old cpu_xxx() APIs is planned to removed later. then, converted.

Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-05-25 08:24:11 -04:00
Mike Frysinger 00b5c50e47 Blackfin: optimize MMR reads during startup a bit
Since the value of these MMRs aren't changing, store the value in a local
variable and work off of that.  This avoids multiple MMR reads which are
implicitly forced by the volatile markings.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-05-25 08:13:43 -04:00
Mike Frysinger 6327a574f9 Blackfin: move internal irq prototypes out of global namespace
These are only used in a few internal Blackfin places, so move the irq
prototypes out of the global header and into the internal irq one.  No
functional changes other than shuffling locales.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-05-25 08:13:43 -04:00
Mike Frysinger 3086fd2768 Blackfin: bf51x/bf52x: fix typo in hysteresis MMR names
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-05-25 08:13:42 -04:00
Mike Frysinger 2951acba85 Blackfin: SMP: drop unused blackfin_cpudata.idle pointer
Not sure when we stopped using this field, but nothing in the tree uses
this now, so punt it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-05-25 08:13:42 -04:00
Mike Frysinger 44491fbc5a Blackfin: SMP: fix cpudata cache setup
After some cache setup reordering changesets, the blackfin_cpudata init
was left behind.  While cpu0's data was correct, cpu1's data was not.
Not that big of a deal as these are only used in the cpuinfo output, but
should still be fixed.  So move the setup of these fields to the common
cache setup function to avoid this happening again in the future.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-05-25 08:13:42 -04:00
Mike Frysinger 8d011f70b0 Blackfin: clean up /proc/cpuinfo output
The smp flush lines are too long and have too many newlines, so scale
them back to match the other lines.

The %p modifier shows "(null)" for 0, so use %08x instead.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-05-25 08:13:42 -04:00
Sonic Zhang c6345ab1a3 Blackfin: SMP: work around anomaly 05000491
In order to safely work around anomaly 05000491, we have to execute IFLUSH
from L1 instruction sram.  The trouble with multi-core systems is that all
L1 sram is visible only to the active core.  So we can't just place the
functions into L1 and call it directly.  We need to setup a jump table and
place the entry point in external memory.  This will call the right func
based on the active core.

In the process, convert from the manual relocation of a small bit of code
into Core B's L1 to the more general framework we already have in place
for loading arbitrary pieces of code into L1.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-03-18 04:01:04 -04:00
Michael Hennerich 7a4a207e74 Blackfin: BF51x/BF52x: support GPIO Hysteresis/Schmitt Trigger options
Newer parts have optional Hysteresis/Schmitt Trigger options to help with
dirty signals.  So add some kconfig options for tuning this and enable it
by default for people.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:52 -04:00
Mike Frysinger be1577e378 Blackfin: another year of changes (update copyright in boot log)
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-22 14:19:11 -04:00
Graf Yang 718340f629 Blackfin: rewrite resync_core_{i,d}cache() SMP logic to avoid per_cpu data
This functions are implicitly called by core functions like cpu_relax(),
and since those functions may be called early on before common code has
initialized the per-cpu data area, we need to tweak the stats gathering.
Now the statistics are maintained in common bss which makes these funcs
safe to use as soon as the C runtime env is setup.

Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-03-09 00:30:50 -05:00
Barry Song d86bfb1600 Blackfin: initial XIP support
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-03-09 00:30:48 -05:00
Barry Song 6feda3a653 Blackfin: replace harcoded define with proper THREAD_SIZE macro
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-03-09 00:30:48 -05:00
Barry Song e18e7dd334 Blackfin: fix MPU page permission masks overflow when dealing with async memory
Attempting to use the MPU while doing XIP out of parallel flash hooked up
to the async memory bus would often result in random crashes as the MPU
slowly corrupted memory.

The fallout here is that the async banks gain MPU protection from user
space too.  So any accesses have to go through the mmap() interface rather
than just using hardcoded pointers.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-03-09 00:30:46 -05:00
Sonic Zhang b635f1912d Blackfin: allow boards to register early devices
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-03-09 00:30:45 -05:00
Barry Song d45e8db1b2 Blackfin: drop 4KB reserve at end of memory
The point of this small chunk was to avoid anomaly 05000310.  This never
really seemed to do what it was intended though -- no valid CPLBs exist
over the reserved memory, and there is often memory before it anyways (due
to the uClinux MTD and/or reserved DMA region).  Plus, it doesn't address
the L1 instruction case.

So drop this chunk as it wastes memory and is affront to humanity.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-12-15 00:15:50 -05:00
Robin Getz 7a1a8cc190 Blackfin: announce current cpu rev when booting
User reports rarely include full information, so include this important
tidbit up front.  It's also good to know at a glance in general.

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-12-15 00:15:01 -05:00
Mike Frysinger 5cd82a6d58 Blackfin: calculate on-chip lengths at link time rather than run time
Since the link sizes never change at runtime, push the calculation out to
the linker script to save some useless calculation costs.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-12-15 00:13:55 -05:00
Robin Getz 96f1050d3d Blackfin: mass clean up of copyright/licensing info
Bill Gatliff & David Brownell pointed out we were missing some
copyrights, and licensing terms in some of the files in
./arch/blackfin, so this fixes things, and cleans them up.

It also removes:
 - verbose GPL text(refer to the top level ./COPYING file)
 - file names (you are looking at the file)
 - bug url (it's in the ./MAINTAINERS file)
 - "or later" on GPL-2, when we did not have that right

It also allows some Blackfin-specific assembly files to be under a BSD
like license (for people to use them outside of Linux).

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-10-07 04:36:26 -04:00
Michael Hennerich 05d17dfaab Blackfin: fix spelling in a few comments
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-16 22:10:33 -04:00
Mike Frysinger 3aa670419a Blackfin: punt dead cache locking code
No one uses these functions, and some are duplicate of existing C code.  So
just punt the whole thing.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-16 22:10:25 -04:00
Robin Getz 837ec2d56c Blackfin: catch hardware errors earlier during booting
Allow hardware errors to be caught during early portions of booting, and
leave something in the shadow console that people can use to debug their
system with (to be printed out by the bootloader on next reset).

This enables the hardare error interrupts in head.S, allowing us to find
hardware errors when they happen (well, as much as you can with a hardware
error) and prints out the trace if it is enabled.  This will catch errors
(like booting the wrong image on a 533) which previously resulted in a
infinite loop/hang, as well as random hardware errors before before
setup_arch().

To disable this debug only feature - turn off EARLY_PRINTK.

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-16 21:31:44 -04:00
Robin Getz 3f871feaf3 Blackfin: add an early shadow console
Add a memory based shadow console to keep a copy of the printk buffer in a
location which can be found externally.  This allows bootloaders to locate
and utilize the log buffer in case of silent (early/resume/etc...) crashes.

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-16 21:31:43 -04:00
Robin Getz 2f812c0bd5 Blackfin: clean up early memory setup code
Remove code duplication, and only print out memory warnings when they are
an actual problem.

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-16 21:28:54 -04:00
Michael Hennerich c70c754ff9 Blackfin: drop per-cpu loops_per_jiffy tracking
On Blackfin SMP, a per-cpu loops_per_jiffy is pointless since both cores
always run at the same CCLK.  In addition, the current implementation has
flaws since the main consumer for loops_per_jiffy (asm/delay.h) uses the
global kernel loops_per_jiffy and not the per_cpu one.  So punt all of the
per-cpu handling and go back to the global shared one.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-07-16 01:52:44 -04:00
Robin Getz 3a920accbb Blackfin: drop duplicate runtime checking of anomaly 05000448
We already catch this anomaly at compile time, and the runtime version is
such that it ends up checking on all parts rather than just the ones that
might actually have it.

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-07-16 01:52:34 -04:00
Robin Getz dc437b1b59 Blackfin: fix silent crash when no uClinux MTD filesystem exists
Since we need to relocate the attached filesystem with the uClinux MTD map
(to handle some anomalies), we need to know its real filesize.  If we boot
a kernel without a filesystem actually attached, we end up blindly reading
and copying garbage (since there is no magic value to detect validity).
Often times this results in an early crash and no output.  So add a few
basic sanity checks before operating on things to catch the majority of
cases.

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-07-16 01:52:21 -04:00
Mike Frysinger b2dc0a0884 Blackfin: drop dead flash_probe call
There are no CONFIG_{BLK,CHR}_DEV_FLASH Kconfig options, and there is no
flash_probe() function, so not really sure what this code is all about.
Seems to be dead code that stretches way back to the start of the Blackfin
port.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-07-16 01:39:45 -04:00
Joe Perches ad361c9884 Remove multiple KERN_ prefixes from printk formats
Commit 5fd29d6ccb ("printk: clean up
handling of log-levels and newlines") changed printk semantics.  printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.

<level> is now included in the output on each additional use.

Remove all uses of multiple KERN_<level>s in formats.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-07-08 10:30:03 -07:00
Robin Getz bd854c077e Blackfin: fix early crash when booting on wrong cpu
Make sure we process the kernel command line before poking the hardware,
so that we can process early printk.  This helps ensure that if you boot
a kernel configured for a different processor, something will be left in
the log buffer.

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-22 21:16:17 -04:00
Jie Zhang 41ba653f24 Blackfin: decouple unrelated cache settings to get exact behavior
The current cache options don't really represent the hardware features.
They end up setting different aspects of the hardware so that the end
result is to turn on/off the cache.  Unfortunately, when we hit cache
problems with the hardware, it's difficult to test different settings to
root cause the problem.  The current settings also don't cleanly allow for
different caching behaviors with different regions of memory.

So split the configure options such that they properly reflect the settings
that are applied to the hardware.

Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-22 21:15:59 -04:00
Sonic Zhang 0de4adfb8c Blackfin: fix accidental reset in some boot modes
We read the SWRST (Software Reset) register to get at the last reset
state, and then we may configure the DOUBLE_FAULT bit to control behavior
when a double fault occurs.  But if the lower bits of the register is
already set (like UART boot mode on a BF54x), we inadvertently make the
system reset by writing to the SYSTEM_RESET field at the same time.  So
make sure the lower 4 bits are always cleared.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-22 21:15:48 -04:00
Sonic Zhang 47e9dedb72 Blackfin: add blackfin_invalidate_entire_icache for SMP systems
The KGDB code uses this when switching processors to make sure the icache
is in a valid state.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-13 07:20:07 -04:00
Robin Getz 2466ac6556 Blackfin: include the cpu compiled version in /proc/cpuinfo
Since the compiled-for cpu revision can be significant, include it in the
cpuinfo output along side the cpu revision we're currently running on.

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-13 07:20:07 -04:00
Mike Frysinger 79df1b6947 Blackfin: override default uClinux MTD addr/size
Due to a processor anomaly (05000263 to be exact), most Blackfin parts
cannot keep the embedded filesystem image directly after the kernel in
RAM.  Instead, the filesystem needs to be relocated to the end of memory.
As such, we need to tweak the map addr/size during boot for Blackfin
systems.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-12 06:11:53 -04:00