commit c128a1b0523b685c8856ddc0ac0e1caef1fdeee5 upstream.
Errata i2310[0] says, Erroneous timeout can be triggered,
if this Erroneous interrupt is not cleared then it may leads
to storm of interrupts.
Commit 9d141c1e6157 ("serial: 8250_omap: Implementation of Errata i2310")
which added the workaround but missed ensuring RX FIFO is really empty
before applying the errata workaround as recommended in the errata text.
Fix this by adding back check for UART_OMAP_RX_LVL to be 0 for
workaround to take effect.
[0] https://www.ti.com/lit/pdf/sprz536 page 23
Fixes: 9d141c1e6157 ("serial: 8250_omap: Implementation of Errata i2310")
Cc: stable@vger.kernel.org
Reported-by: Vignesh Raghavendra <vigneshr@ti.com>
Closes: https://lore.kernel.org/all/e96d0c55-0b12-4cbf-9d23-48963543de49@ti.com/
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240625160725.2102194-1-u-kumar1@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c92a8bd53f24d50c8cf4aba53bb75505b382fed upstream.
Most of the colfires have up to 5 UARTs but MCF54418 has up-to 10 !
Change the maximum value authorized.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@yoseli.org>
Cc: stable <stable@kernel.org>
Fixes: 2545cf6e94 ("m68knommu: allow 4 coldfire serial ports")
Link: https://lore.kernel.org/r/20240620-upstream-uart-v1-1-a9d0d95fb19e@yoseli.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d141c1e615795eeb93cd35501ad144ee997a826 upstream.
As per Errata i2310[0], Erroneous timeout can be triggered,
if this Erroneous interrupt is not cleared then it may leads
to storm of interrupts, therefore apply Errata i2310 solution.
[0] https://www.ti.com/lit/pdf/sprz536 page 23
Fixes: b67e830d38 ("serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240619105903.165434-1-u-kumar1@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33bb2f6ac3 upstream.
This patch reworks RX support over DMA to improve reliability:
- change dma buffer cyclic configuration by using 2 periods. DMA buffer
data are handled by a flip-flop between the 2 periods in order to avoid
risk of data loss/corruption
- change the size of dma buffer to 4096 to limit overruns
- add rx errors management (breaks, parity, framing and overrun).
When an error occurs on the uart line, the dma request line is masked at
HW level. The SW must 1st clear DMAR (dma request line enable), to
handle the error, then re-enable DMAR to recover. So, any correct data
is taken from the DMA buffer, before handling the error itself. Then
errors are handled from RDR/ISR/FIFO (e.g. in PIO mode). Last, DMA
reception is resumed.
- add a condition on DMA request line in DMA RX routines in order to
switch to PIO mode when no DMA request line is disabled, even if the DMA
channel is still enabled.
When the UART is wakeup source and is configured to use DMA for RX, any
incoming data that wakes up the system isn't correctly received.
At data reception, the irq_handler handles the WUF irq, and then the
data reception over DMA.
As the DMA transfer has been terminated at suspend, and will be restored
by resume callback (which has no yet been called by system), the data
can't be received.
The wake-up data has to be handled in PIO mode while suspend callback
has not been called.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211020150332.10214-3-erwan.leray@foss.st.com
[ dario: fix conflicts for backport to v5.15. From the [1] series, only the
first patch was applied to the v5.15 branch. This caused a regression in
character reception, which can be fixed by applying the second patch. The
patch has been tested on the stm32f469-disco board.
[1] https://lore.kernel.org/all/20211020150332.10214-1-erwan.leray@foss.st.com/. ]
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e533e4c62e9993e62e947ae9bbec34e4c7ae81c2 ]
By waiting at most 1 second for USR2_TXDC to be set, we avoid a potential
deadlock.
In case of the timeout, there is not much we can do, so we simply ignore
the transmitter state and optimistically try to continue.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/919647898c337a46604edcabaf13d42d80c0915d.1712837613.git.esben@geanix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5208e7ced520a813b4f4774451fbac4e517e78b2 upstream.
The FIFO is 64 bytes, but the FCR is configured to fire the TX interrupt
when the FIFO is half empty (bit 3 = 0). Thus, we should only write 32
bytes when a TX interrupt occurs.
This fixes a problem observed on the PXA168 that dropped a bunch of TX
bytes during large transmissions.
Fixes: ab28f51c77 ("serial: rewrite pxa2xx-uart to use 8250_core")
Signed-off-by: Doug Brown <doug@schmorgal.com>
Link: https://lore.kernel.org/r/20240519191929.122202-1-doug@schmorgal.com
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8492bd91aa055907c67ef04f2b56f6dadd1f44bf ]
When using a high speed clock with a low baud rate, the 4x prescaler is
automatically selected if required. In that case, sc16is7xx_set_baud()
properly configures the chip registers, but returns an incorrect baud
rate by not taking into account the prescaler value. This incorrect baud
rate is then fed to uart_update_timeout().
For example, with an input clock of 80MHz, and a selected baud rate of 50,
sc16is7xx_set_baud() will return 200 instead of 50.
Fix this by first changing the prescaler variable to hold the selected
prescaler value instead of the MCR bitfield. Then properly take into
account the selected prescaler value in the return value computation.
Also add better documentation about the divisor value computation.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20240430200431.4102923-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e57cefc4477659527f7adab1f87cdbf60ef1ae6 ]
To better show why the limit is what it is, since we have only 16 bits for
the divisor.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-13-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 8492bd91aa05 ("serial: sc16is7xx: fix bug in sc16is7xx_set_baud() when using prescaler")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aae20f6e34cd0cbd67a1d0e5877561c40109a81b ]
The to-be-fixed commit removed locking when invalidating the DMA RX
descriptors on shutdown. It overlooked that there is still a rx_timer
running which may still access the protected data. So, re-add the
locking.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Closes: https://lore.kernel.org/r/ee6c9e16-9f29-450e-81da-4a8dceaa8fc7@de.bosch.com
Fixes: 2c4ee23530 ("serial: sh-sci: Postpone DMA release when falling back to PIO")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240506114016.30498-7-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a8e4ab0c93fad30769479f86849e22d63cd0e12 ]
Replace incorrect include with the proper one for sched_set_fifo()
declaration.
Fixes: 28d2f209cd ("sched,serial: Convert to sched_set_fifo()")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240409154253.3043822-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e60955dbecb97f080848a57524827e2db29c70fd ]
Sparse is not happy about misuse of bitwise types:
.../max3100.c:194:13: warning: incorrect type in assignment (different base types)
.../max3100.c:194:13: expected unsigned short [addressable] [usertype] etx
.../max3100.c:194:13: got restricted __be16 [usertype]
.../max3100.c:202:15: warning: cast to restricted __be16
Fix this by choosing proper types for the respective variables.
Fixes: 7831d56b0a ("tty: MAX3100")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240402195306.269276-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 712a1fcb38dc7cac6da63ee79a88708fbf9c45ec ]
The removal of the last MAX3100 device triggers the removal of
the driver. However, code doesn't update the respective global
variable and after insmod — rmmod — insmod cycle the kernel
oopses:
max3100 spi-PRP0001:01: max3100_probe: adding port 0
BUG: kernel NULL pointer dereference, address: 0000000000000408
...
RIP: 0010:serial_core_register_port+0xa0/0x840
...
max3100_probe+0x1b6/0x280 [max3100]
spi_probe+0x8d/0xb0
Update the actual state so next time UART driver will be registered
again.
Hugo also noticed, that the error path in the probe also affected
by having the variable set, and not cleared. Instead of clearing it
move the assignment after the successfull uart_register_driver() call.
Fixes: 7831d56b0a ("tty: MAX3100")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240402195306.269276-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77ab53371a2066fdf9b895246505f5ef5a4b5d47 ]
uart_handle_cts_change() has to be called with port lock taken,
Since we run it in a separate work, the lock may not be taken at
the time of running. Make sure that it's taken by explicitly doing
that. Without it we got a splat:
WARNING: CPU: 0 PID: 10 at drivers/tty/serial/serial_core.c:3491 uart_handle_cts_change+0xa6/0xb0
...
Workqueue: max3100-0 max3100_work [max3100]
RIP: 0010:uart_handle_cts_change+0xa6/0xb0
...
max3100_handlerx+0xc5/0x110 [max3100]
max3100_work+0x12a/0x340 [max3100]
Fixes: 7831d56b0a ("tty: MAX3100")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240402195306.269276-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 614a19b89ca43449196a8af1afac7d55c6781687 upstream.
There is a scenario when resuming from some power saving states
with no_console_suspend where console output can be generated
before the 8250_bcm7271 driver gets the opportunity to restore
the baud_mux_clk frequency. Since the baud_mux_clk is at its
default frequency at this time the output can be garbled until
the driver gets the opportunity to resume.
Since this is only an issue with console use of the serial port
during that window and the console isn't likely to use baud
rates that require alternate baud_mux_clk frequencies, allow the
driver to select the default_mux_rate if it is accurate enough.
Fixes: 41a469482d ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240424222559.1844045-1-opendmb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70d7f1427afcf7fa2d21cb5a04c6f3555d5b9357 upstream.
The current implementation uses either gsm0_receive() or gsm1_receive()
depending on whether the user configured the mux in basic or advanced
option mode. Both functions share some state values over the same logical
elements of the frame. However, both frame types differ in their nature.
gsm0_receive() uses non-transparency framing, whereas gsm1_receive() uses
transparency mechanism. Switching between both modes leaves the receive
function in an undefined state when done during frame reception.
Fix this by splitting both states. Add gsm0_receive_state_check_and_fix()
and gsm1_receive_state_check_and_fix() to ensure that gsm->state is reset
after a change of gsm->receive.
Note that gsm->state is only accessed in:
- gsm0_receive()
- gsm1_receive()
- gsm_error()
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20240424054842.7741-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47388e807f85948eefc403a8a5fdc5b406a65d5a upstream.
Assuming the following:
- side A configures the n_gsm in basic option mode
- side B sends the header of a basic option mode frame with data length 1
- side A switches to advanced option mode
- side B sends 2 data bytes which exceeds gsm->len
Reason: gsm->len is not used in advanced option mode.
- side A switches to basic option mode
- side B keeps sending until gsm0_receive() writes past gsm->buf
Reason: Neither gsm->state nor gsm->len have been reset after
reconfiguration.
Fix this by changing gsm->count to gsm->len comparison from equal to less
than. Also add upper limit checks against the constant MAX_MRU in
gsm0_receive() and gsm1_receive() to harden against memory corruption of
gsm->len and gsm->mru.
All other checks remain as we still need to limit the data according to the
user configuration and actual payload size.
Reported-by: j51569436@gmail.com
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218708
Tested-by: j51569436@gmail.com
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20240424054842.7741-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2aba15ad6f908d1a620fd97f6af5620c3639742 upstream.
Currently, when kdb is compiled with keyboard support, then we will use
schedule_work() to provoke reset of the keyboard status. Unfortunately
schedule_work() gets called from the kgdboc post-debug-exception
handler. That risks deadlock since schedule_work() is not NMI-safe and,
even on platforms where the NMI is not directly used for debugging, the
debug trap can have NMI-like behaviour depending on where breakpoints
are placed.
Fix this by using the irq work system, which is NMI-safe, to defer the
call to schedule_work() to a point when it is safe to call.
Reported-by: Liuye <liu.yeC@h3c.com>
Closes: https://lore.kernel.org/all/20240228025602.3087748-1-liu.yeC@h3c.com/
Cc: stable@vger.kernel.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240424-kgdboc_fix_schedule_work-v2-1-50f5a490aec5@linaro.org
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 54c4ec5f8c471b7c1137a1f769648549c423c026 ]
The uart_handle_cts_change() function in serial_core expects the caller
to hold uport->lock. For example, I have seen the below kernel splat,
when the Bluetooth driver is loaded on an i.MX28 board.
[ 85.119255] ------------[ cut here ]------------
[ 85.124413] WARNING: CPU: 0 PID: 27 at /drivers/tty/serial/serial_core.c:3453 uart_handle_cts_change+0xb4/0xec
[ 85.134694] Modules linked in: hci_uart bluetooth ecdh_generic ecc wlcore_sdio configfs
[ 85.143314] CPU: 0 PID: 27 Comm: kworker/u3:0 Not tainted 6.6.3-00021-gd62a2f068f92 #1
[ 85.151396] Hardware name: Freescale MXS (Device Tree)
[ 85.156679] Workqueue: hci0 hci_power_on [bluetooth]
(...)
[ 85.191765] uart_handle_cts_change from mxs_auart_irq_handle+0x380/0x3f4
[ 85.198787] mxs_auart_irq_handle from __handle_irq_event_percpu+0x88/0x210
(...)
Cc: stable@vger.kernel.org
Fixes: 4d90bb147e ("serial: core: Document and assert lock requirements for irq helpers")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Emil Kronborg <emil.kronborg@protonmail.com>
Link: https://lore.kernel.org/r/20240320121530.11348-1-emil.kronborg@protonmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1be3226445362bfbf461c92a5bcdb1723f2e4907 upstream.
The mitigation was intended to stop the irq completely. That may be
better than a hard lock-up but it turns out that you get a crash anyway
if you're using pmac_zilog as a serial console:
ttyPZ0: pmz: rx irq flood !
BUG: spinlock recursion on CPU#0, swapper/0
That's because the pr_err() call in pmz_receive_chars() results in
pmz_console_write() attempting to lock a spinlock already locked in
pmz_interrupt(). With CONFIG_DEBUG_SPINLOCK=y, this produces a fatal
BUG splat. The spinlock in question is the one in struct uart_port.
Even when it's not fatal, the serial port rx function ceases to work.
Also, the iteration limit doesn't play nicely with QEMU, as can be
seen in the bug report linked below.
A web search for other reports of the error message "pmz: rx irq flood"
didn't produce anything. So I don't think this code is needed any more.
Remove it.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Aneesh Kumar K.V <aneesh.kumar@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable@kernel.org
Cc: linux-m68k@lists.linux-m68k.org
Link: https://github.com/vivier/qemu-m68k/issues/44
Link: https://lore.kernel.org/all/1078874617.9746.36.camel@gaston/
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@kernel.org>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/e853cf2c762f23101cd2ddec0cc0c2be0e72685f.1712568223.git.fthain@linux-m68k.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67c3775689 upstream.
Any unprivileged user can attach N_GSM0710 ldisc, but it requires
CAP_NET_ADMIN to create a GSM network anyway.
Require initial namespace CAP_NET_ADMIN to do that.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Link: https://lore.kernel.org/r/20230731185942.279611-1-cascardo@canonical.com
Cc: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbf4ab821804df071c8b566d9813083125e6d97b upstream.
The SC16IS7XX IC supports a burst mode to access the FIFOs where the
initial register address is sent ($00), followed by all the FIFO data
without having to resend the register address each time. In this mode, the
IC doesn't increment the register address for each R/W byte.
The regmap_raw_read() and regmap_raw_write() are functions which can
perform IO over multiple registers. They are currently used to read/write
from/to the FIFO, and although they operate correctly in this burst mode on
the SPI bus, they would corrupt the regmap cache if it was not disabled
manually. The reason is that when the R/W size is more than 1 byte, these
functions assume that the register address is incremented and handle the
cache accordingly.
Convert FIFO R/W functions to use the regmap _noinc_ versions in order to
remove the manual cache control which was a workaround when using the
_raw_ versions. FIFO registers are properly declared as volatile so
cache will not be used/updated for FIFO accesses.
Fixes: dfeae619d7 ("serial: sc16is7xx")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231211171353.2901416-6-hugo@hugovil.com
Cc: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: GONG, Ruiqi <gongruiqi1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 672448ccf9b6a676f96f9352cbf91f4d35f4084a upstream.
When about to transmit the function imx_uart_start_tx is called and in
some RS485 configurations this function will call imx_uart_stop_rx. The
problem is that imx_uart_stop_rx will enable loopback in order to
release the RS485 bus, but when loopback is enabled transmitted data
will just be looped to RX.
This patch fixes the above problem by not enabling loopback when about
to transmit.
This driver now works well when used for RS485 half duplex master
configurations.
Fixes: 79d0224f6b ("tty: serial: imx: Handle RS485 DE signal active high")
Cc: stable <stable@kernel.org>
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Link: https://lore.kernel.org/r/20240221115304.509811-1-rickaran@axis.com
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1581dafaf0d34bc9c428a794a22110d7046d186d upstream.
This is the same issue that was fixed for the VGA text buffer in commit
39cdb68c64 ("vt: fix memory overlapping when deleting chars in the
buffer"). The cure is also the same i.e. replace memcpy() with memmove()
due to the overlaping buffers.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Fixes: 81732c3b2f ("tty vt: Fix line garbage in virtual console on command line edition")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/sn184on2-3p0q-0qrq-0218-895349s4753o@syhkavp.arg
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74cb7e0355fae9641f825afa389d3fba3b617714 upstream.
If the remote uart device is not connected or not enabled after booting
up, the CTS line is high by default. At this time, if we enable the flow
control when opening the device(for example, using “stty -F /dev/ttyLP4
crtscts” command), there will be a pending idle preamble(first writing 0
and then writing 1 to UARTCTRL_TE will queue an idle preamble) that
cannot be sent out, resulting in the uart port fail to close(waiting for
TX empty), so the user space stty will have to wait for a long time or
forever.
This is an LPUART IP bug(idle preamble has higher priority than CTS),
here add a workaround patch to enable TX CTS after enabling UARTCTRL_TE,
so that the idle preamble does not get stuck due to CTS is deasserted.
Fixes: 380c966c09 ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20240305015706.1050769-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 801410b26a0e8b8a16f7915b2b55c9528b69ca87 ]
During the handoff from earlycon to the real console driver, we have
two separate drivers operating on the same device concurrently. In the
case of the 8250 driver these concurrent accesses cause problems due
to the driver's use of banked registers, controlled by LCR.DLAB. It is
possible for the setup(), config_port(), pm() and set_mctrl() callbacks
to set DLAB, which can cause the earlycon code that intends to access
TX to instead access DLL, leading to missed output and corruption on
the serial line due to unintended modifications to the baud rate.
In particular, for setup() we have:
univ8250_console_setup()
-> serial8250_console_setup()
-> uart_set_options()
-> serial8250_set_termios()
-> serial8250_do_set_termios()
-> serial8250_do_set_divisor()
For config_port() we have:
serial8250_config_port()
-> autoconfig()
For pm() we have:
serial8250_pm()
-> serial8250_do_pm()
-> serial8250_set_sleep()
For set_mctrl() we have (for some devices):
serial8250_set_mctrl()
-> omap8250_set_mctrl()
-> __omap8250_set_mctrl()
To avoid such problems, let's make it so that the console is locked
during pre-registration calls to these callbacks, which will prevent
the earlycon driver from running concurrently.
Remove the partial solution to this problem in the 8250 driver
that locked the console only during autoconfig_irq(), as this would
result in a deadlock with the new approach. The console continues
to be locked during autoconfig_irq() because it can only be called
through uart_configure_port().
Although this patch introduces more locking than strictly necessary
(and in particular it also locks during the call to rs485_config()
which is not affected by this issue as far as I can tell), it follows
the principle that it is the responsibility of the generic console
code to manage the earlycon handoff by ensuring that earlycon and real
console driver code cannot run concurrently, and not the individual
drivers.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Link: https://linux-review.googlesource.com/id/I7cf8124dcebf8618e6b2ee543fa5b25532de55d8
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240304214350.501253-1-pcc@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73b5a5c00be39e23b194bad10e1ea8bb73eee176 ]
It seems a copy&paste mistake that suspend callback removes the GPIO
device. There is no counterpart of this action, means once suspended
there is no more GPIO device available untile full unbind-bind cycle
is performed. Remove suspicious GPIO device removal in suspend.
Fixes: d0aeaa83f0 ("serial: exar: split out the exar code from 8250_pci")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240219150627.2101198-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 314c2b399288f0058a8c5b6683292cbde5f1531b ]
The core expects for tx_empty() either TIOCSER_TEMT when the tx is
empty or 0 otherwise. s3c24xx_serial_txempty_nofifo() might return
0x4, and at least uart_get_lsr_info() tries to clear exactly
TIOCSER_TEMT (BIT(1)). Fix tx_empty() to return TIOCSER_TEMT.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240119104526.1221243-2-tudor.ambarus@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ede8c6f474255b2213cccd7997b993272a8e2f9 ]
Replace g with q.
Helpful when grepping thru source code or logs for
"request" keyword.
Fixes: f65444187a ("serial: New serial driver MAX310X")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240118152213.2644269-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e6a92f67c8a94707f7bb27ac29e2bdf3e7c167d ]
The if (c >= 20 && c <= 0x3f) test added in commit 7a99565f87 is
wrong. 20 is DC4 in ascii and it makes no sense to consider that as the
bottom limit. Instead, it should be 0x20 as in the other test in
the commit above. This is supposed to NOT change anything as we handle
interesting 20-0x20 asciis far before this if.
So for sakeness, change to 0x20 (which is SPACE).
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Fixes: 7a99565f87 ("vt: ignore csi sequences with intermediate characters.")
Cc: Martin Hostettler <textshell@uchuujin.de>
Link: https://lore.kernel.org/all/ZaP45QY2WEsDqoxg@neutronstar.dyndns.org/
Tested-by: Helge Deller <deller@gmx.de> # parisc STI console
Link: https://lore.kernel.org/r/20240122110401.7289-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f42b142ea ]
After upgrading from 5.16 to 6.1, our board with a MAX14830 started
producing lots of garbage data over UART. Bisection pointed out commit
285e76fc04 as the culprit. That patch tried to replace hand-written
code which I added in 2b4bac48c1 ("serial: max310x: Use batched reads
when reasonably safe") with the generic regmap infrastructure for
batched operations.
Unfortunately, the `regmap_raw_read` and `regmap_raw_write` which were
used are actually functions which perform IO over *multiple* registers.
That's not what is needed for accessing these Tx/Rx FIFOs; the
appropriate functions are the `_noinc_` versions, not the `_raw_` ones.
Fix this regression by using `regmap_noinc_read()` and
`regmap_noinc_write()` along with the necessary `regmap_config` setup;
with this patch in place, our board communicates happily again. Since
our board uses SPI for talking to this chip, the I2C part is completely
untested.
Fixes: 285e76fc04 ("serial: max310x: use regmap methods for SPI batch operations")
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://lore.kernel.org/r/79db8e82aadb0e174bc82b9996423c3503c8fb37.1680732084.git.jan.kundrat@cesnet.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3883ab5e9 ]
SPI can only use 5 address bits, since one bit is reserved for
specifying R/W and 2 bits are used to specify the UART port.
To access registers that have addresses past 0x1F, an extended
register space can be enabled by writing to the GlobalCommand
register (address 0x1F).
I2C uses 8 address bits. The R/W bit is placed in the slave
address, and so is the UART port. Because of this, registers
that have addresses higher than 0x1F can be accessed normally.
To access the RevID register, on SPI, 0xCE must be written to
the 0x1F address to enable the extended register space, after
which the RevID register is accessible at address 0x5. 0xCD
must be written to the 0x1F address to disable the extended
register space.
On I2C, the RevID register is accessible at address 0x25.
Create an interface config struct, and add a method for
toggling the extended register space and a member for the RevId
register address. Implement these for SPI.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220605144659.4169853-4-demonsingur@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 3f42b142ea ("serial: max310x: fix IO data corruption in batched operations")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b35f8dbbce818b02c730dc85133dc7754266e084 ]
If there is a problem after resetting a port, the do/while() loop that
checks the default value of DIVLSB register may run forever and spam the
I2C bus.
Add a delay before each read of DIVLSB, and a maximum number of tries to
prevent that situation from happening.
Also fail probe if port reset is unsuccessful.
Fixes: 10d8b34a42 ("serial: max310x: Driver rework")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240116213001.3691629-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ef281daf0 ]
The driver currently does manual register manipulation in
multiple places to talk to a specific UART port.
In order to talk to a specific UART port over SPI, the bits U1
and U0 of the register address can be set, as explained in the
Command byte configuration section of the datasheet.
Make this more elegant by creating regmaps for each UART port
and setting the read_flag_mask and write_flag_mask
accordingly.
All communcations regarding global registers are done on UART
port 0, so replace the global regmap entirely with the port 0
regmap.
Also, remove the 0x1f masks from reg_writeable(), reg_volatile()
and reg_precious() methods, since setting the U1 and U0 bits of
the register address happens inside the regmap core now.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220605144659.4169853-3-demonsingur@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: b35f8dbbce81 ("serial: max310x: prevent infinite while() loop in port startup")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 285e76fc04 ]
The SPI batch read/write operations can be implemented as simple
regmap raw read and write, which will also try to do a gather
write just as it is done here.
Use the regmap raw read and write methods.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220605144659.4169853-2-demonsingur@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: b35f8dbbce81 ("serial: max310x: prevent infinite while() loop in port startup")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84f2faa785 ]
Serial core handles serial_rs485 sanitization.
When em485 init fails, there are two possible paths of entry:
1) uart_rs485_config (init path) that fully clears port->rs485 on
error.
2) ioctl path with a pre-existing, valid port->rs485 unto which the
kernel falls back on error and port->rs485 should therefore be
kept untouched. The temporary rs485 struct is not returned to
userspace in case of error so its flag don't matter.
...Thus SER_RS485_ENABLED clearing on error can/should be dropped.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-37-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3b69e32e151bc4a4e3c785cbdb1f918d5ee337ed upstream.
When DMA is used in RS485 mode make sure that the UARTs tx section is
enabled before the DMA buffers are queued for transmission.
Cc: stable@vger.kernel.org
Fixes: 8d47923772 ("serial: amba-pl011: add RS485 support")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240216224709.9928-2-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0c2a5f471ce58bca8f8ab5fcb911aff91eaaa5eb ]
The UART supports an auto-RTS mode in which the RTS pin is automatically
activated during transmission. So mark this mode as being supported even
if RTS is not controlled by the driver but the UART.
Also the serial core expects now at least one of both modes rts-on-send or
rts-after-send to be supported. This is since during sanitization
unsupported flags are deleted from a RS485 configuration set by userspace.
However if the configuration ends up with both flags unset, the core prints
a warning since it considers such a configuration invalid (see
uart_sanitize_serial_rs485()).
Cc: <stable@vger.kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20240103061818.564-8-l.sanfilippo@kunbus.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 93cd256ab224c2519e7c4e5f58bb4f1ac2bf0965 upstream.
Some people are seeing a warning similar to this when using a crystal:
max310x 11-006c: clock is not stable yet
The datasheet doesn't mention the maximum time to wait for the clock to be
stable when using a crystal, and it seems that the 10ms delay in the driver
is not always sufficient.
Jan Kundrát reported that it took three tries (each separated by 10ms) to
get a stable clock.
Modify behavior to check stable clock ready bit multiple times (20), and
waiting 10ms between each try.
Note: the first draft of the driver originally used a 50ms delay, without
checking the clock stable bit.
Then a loop with 1000 retries was implemented, each time reading the clock
stable bit.
Fixes: 4cf9a888fd ("serial: max310x: Check the clock readiness")
Cc: stable@vger.kernel.org
Suggested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://www.spinics.net/lists/linux-serial/msg35773.html
Link: https://lore.kernel.org/all/20240110174015.6f20195fde08e5c9e64e5675@hugovil.com/raw
Link: e5dfe3e4a7
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240116213001.3691629-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0419373333c2f2024966d36261fd82a453281e80 upstream.
If regmap_read() returns a non-zero value, the 'val' variable can be left
uninitialized.
Clear it before calling regmap_read() to make sure we properly detect
the clock ready bit.
Fixes: 4cf9a888fd ("serial: max310x: Check the clock readiness")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240116213001.3691629-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e0f25b8992345aa5f113da2815f5add98738c611 ]
The capability CAP_CHECKPOINT_RESTORE was introduced to allow non-root
users to checkpoint and restore processes as non-root with CRIU.
This change extends CAP_CHECKPOINT_RESTORE to enable the CRIU option
'--shell-job' as non-root. CRIU's man-page describes the '--shell-job'
option like this:
Allow one to dump shell jobs. This implies the restored task will
inherit session and process group ID from the criu itself. This option
also allows to migrate a single external tty connection, to migrate
applications like top.
TIOCSLCKTRMIOS can only be done if the process has CAP_SYS_ADMIN and
this change extends it to CAP_SYS_ADMIN or CAP_CHECKPOINT_RESTORE.
With this change it is possible to checkpoint and restore processes
which have a tty connection as non-root if CAP_CHECKPOINT_RESTORE is
set.
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Adrian Reber <areber@redhat.com>
Acked-by: Andrei Vagin <avagin@gmail.com>
Link: https://lore.kernel.org/r/20231208143656.1019-1-areber@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66aad7d8d3ec5a3a8ec2023841bcec2ded5f65c9 ]
In ACM support for sending breaks to devices is optional.
If a device says that it doenot support sending breaks,
the host must respect that.
Given the number of optional features providing tty operations
for each combination is not practical and errors need to be
returned dynamically if unsupported features are requested.
In case a device does not support break, we want the tty layer
to treat that like it treats drivers that statically cannot
support sending a break. It ignores the inability and does nothing.
This patch uses EOPNOTSUPP to indicate that.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 9e98966c7b ("tty: rework break handling")
Link: https://lore.kernel.org/r/20231207132639.18250-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24f2cd019946fc2e88e632d2e24a34c2cc3f2be4 ]
Now, the "jumped-over" code is simple enough to be put inside an 'if'.
Do so to make it 'goto'-less.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230919085156.1578-16-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 66aad7d8d3ec ("usb: cdc-acm: return correct error code on unsupported break")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd99392b643b824813df2edbaebe26a2136d31e6 ]
msleep_interruptible() will check on its own. So no need to do the check
in send_break() before calling the above.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230919085156.1578-15-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 66aad7d8d3ec ("usb: cdc-acm: return correct error code on unsupported break")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66619686d187b4a6395316b7f39881e945dce4bc ]
If the driver sets TTY_DRIVER_HARDWARE_BREAK, we leave ops->break_ctl()
to the driver and return from send_break(). But we do it using a local
variable and keep the code flowing through the end of the function.
Instead, do 'return' immediately with the ops->break_ctl()'s return
value.
This way, we don't have to stuff the 'else' branch of the 'if' with the
software break handling. And we can re-indent the function too.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230919085156.1578-14-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 66aad7d8d3ec ("usb: cdc-acm: return correct error code on unsupported break")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78d60dae9a0c9f09aa3d6477c94047df2fe6f7b0 ]
When using the serial port as RS485 port, the tx statemachine is used to
control the RTS pin to drive the RS485 transceiver TX_EN pin. When the
TTY port is closed in the middle of a transmission (for instance during
userland application crash), imx_uart_shutdown disables the interface
and disables the Transmission Complete interrupt. afer that,
imx_uart_stop_tx bails on an incomplete transmission, to be retriggered
by the TC interrupt. This interrupt is disabled and therefore the tx
statemachine never transitions out of SEND. The statemachine is in
deadlock now, and the TX_EN remains low, making the interface useless.
imx_uart_stop_tx now checks for incomplete transmission AND whether TC
interrupts are enabled before bailing to be retriggered. This makes sure
the state machine handling is reached, and is properly set to
WAIT_AFTER_SEND.
Fixes: cb1a609236 ("serial: imx: implement rts delaying for rs485")
Signed-off-by: Paul Geurts <paul_geurts@live.nl>
Tested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Eberhard Stoll <eberhard.stoll@gmx.de>
Link: https://lore.kernel.org/r/AM0PR09MB26758F651BC1B742EB45775995B8A@AM0PR09MB2675.eurprd09.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Udit Kumar
Jean-Michel Hautbois
Erwan Le Ray
Parker Newman
Esben Haabendal
Doug Brown
Hugo Villeneuve
Wolfram Sang
Andy Shevchenko
Doug Berger
Daniel Starke
Daniel Thompson
Emil Kronborg
Finn Thain
Thadeu Lima de Souza Cascardo
Rickard x Andersson
Nicolas Pitre
Sherry Sun
Peter Collingbourne
Tudor Ambarus
Jiri Slaby (SUSE)
Jan Kundrát
Cosmin Tanislav
Ilpo Järvinen
Lino Sanfilippo
Adrian Reber
Christoph Niedermaier
Oliver Neukum
Paul Geurts