Check that the DIP is enabled on the right port on IBX and VLV/CHV as
we're doing on g4x, and also check for all the infoframe enable bits on
all platforms.
Eventually we should track each infoframe type independently, and also
their contents. This is a small step in that direction as .infoframe_enabled()
return value could be easily turned into a bitmask.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we just disable the GCP infoframe when turning off the port.
That means if the same transcoder is used on a DP port next, we might
end up pushing infoframes over DP, which isn't intended. Just disable
all the infoframes when turning off the port.
Also protect against two ports stomping on each other on g4x due to
the single video DIP instance. Now only the first port to enable
gets to send infoframes.
v2: Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow the procedure listed in Bspec to toggle the port enable bit off
and on when enabling HDMI with 12bpc and pixel repeat on IBX. The old
code didn't actually enable the port before "toggling" the bit back off,
so the whole workaround was essentially a nop.
Also take the opportunity to clarify the code by splitting the gmch
platforms to a separate (much more straightforward) function.
v2: Rebased due to crtc->config changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IBX BSpec says we must specify 8bpc in TRANSCONF for both 8bpc
and 12bpc HDMI output. Do so.
v2: Pass intel_crtc to intel_pipe_has_type()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When the video timings are suitably aligned so that all different
periods start at phase 0 (ie. none of the periods start mid-pixel)
we can inform the sink about this. Supposedly the sink can then
optimize certain things. Obviously this is only relevant when
outputting >8bpc data since otherwise there are no mid-pixel phases.
v2: Rebased due to crtc->config changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GCP infoframes are required to inform the HDMI sink about the color
depth.
Send the GCP infoframe whenever the sink supports any deep color modes
since such sinks must anyway be capable of receiving them. For sinks
that don't support deep color let's skip the GCP in case it might
confuse the sink, although HDMI 1.4 spec does say all sinks must be
capable of reciving them. In theory we could skip the GCP infoframe
for deep color sinks in 8bpc mode as well since sinks must fall back to
8bpc whenever GCP isn't received for some time.
BSpec says we should disable GCP after disabling the port, so do that as
well.
v2: s/intel_set_gcp_infoframe/intel_hdmi_set_gcp_infoframe/
Rebased due to crtc->config changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Resolve conflict with lack of chv phy patches and fixup typo
Chandra spotted.]
Reviewed-by: Chandra Konduru <Chandra.konduru@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CPT/PPT require a specific procedure for enabling 12bpc HDMI. Implement
it, and to keep things neat pull the code into a function.
v2: Rebased due to crtc->config changes
s/HDMI_GC/HDMIUNIT_GC/ to match spec better
Factor out intel_enable_hdmi_audio()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-By: Chandra Konduru <Chandra.konduru@intel.com>
Testecase: igt/kms_render/*
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to bspec the DDI PHY vswing scale value is "don't care" in
case the scale enable bit [27] is clear. But this doesn't seem to be
correct. The scale value seems to also matter if the scale mode bit
[26] is set. So both bit 26 and 27 depend on the value. Setting the
scale value to 0 while either bit is set results in a failed modeset on
HDMI (sink reports no signal).
After reset the scale value is 0x98, but according to the spec we have
to program it to 0x9a. So for consistency program it always to 0x9a
regardless of the scale enable bit.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Matt Roper <matthew.d.roper@intel.com>
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ville's and Mika's cdclk series was in flight at the same time as the
SKL S3 patches so we were missing that update.
intel_update_max_cdclk() and intel_update_cdclk() had to be moved up a
bit to avoid forward declarations.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
intel_update_cdclk() will already display the boot CDCLK for DDI
platforms, no need to repeat there.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We can operate with DPLL0 off with CDCLK backed by the 24Mhz reference
clock, and that's a supported configuration. Don't warn when notice
DPLL0 is off then.
We still have a separate warn at boot if cdclk is disabled (because we
don't currently try to handle the case (that shouldn't happen on SKL as
far as I know) where we boot with display not initialized.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add support for changing cdclk frequency during runtime on BDW.
Also with IPS enabled the actual pixel rate mustn't exceed 95% of cdclk,
so take that into account when computing the max pixel rate.
v2: Grab rps.hw_lock around sandybridge_pcode_write()
v3: Rebase due to power well vs. .global_resources() reordering
v4: Rebased to the latest
v5: Rebased to the latest
v6: Patch order shuffle so that Broadwell CD clock change is
applied before the patch for Haswell CD clock change
v7: Fix for patch style problems
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We need to tell BDW ULT and ULX apart.
v2: Rebased to the latest
v3: Rebased to the latest
v4: Fix for patch style problems
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Bspec says we shouldn't enable IPS on BDW when the pipe pixel rate
exceeds 95% of the core display clock. Apparently this can cause
underruns.
There's no similar restriction listed for HSW, so leave that one alone
for now.
v2: Add pipe_config_supports_ips() (Chris)
v3: Compare against the max cdclk insted of the current cdclk
v4: Rebased to the latest
v5: Rebased to the latest
v6: Fix for patch style problems
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83497
Tested-by: Timo Aaltonen <tjaalton@ubuntu.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Keep the cdclk maximum supported frequency around in dev_priv so that we
can verify certain things against it before actually changing the cdclk
frequency.
For now only VLV/CHV have support changing cdclk frequency, so other
plarforms get to assume cdclk is fixed.
v2: Rebased to the latest
v3: Rebased to the latest
v4: Fix for patch style problems
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Rather than reading out the current cdclk value use the cached value we
have tucked away in dev_priv.
v2: Rebased to the latest
v3: Rebased to the latest
v4: Fix for patch style problems
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Rather that extracting the current cdclk freuqncy every time someone
wants to know it, cache the current value and use that. VLV/CHV already
stored a cached value there so just expand that to cover all platforms.
v2: Rebased to the latest
v3: Rebased to the latest
v4: Rebased to the latest
v5: Removed spurious call to 'intel_update_cdclk(dev)' based on
Damien Lespiau's comment
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVa7zvAAoJEHm+PkMAQRiGtfMIAILs3sxFtrC1hApgcfRLF/7z
K34bwTRqErzqUO/orTwakEr9kSIpIL0zIPSryTCOTPZLfMGkQjhHXO3KR/DSbbTV
MZ8y/BM/yelFA/Np+1LjbiYjTNRnTRvCoaQihkIH8Rn02g7ob9HyL4gIGKpuGFcZ
04GacL2cgChqsRSACdNef948jCoJXKgcuDpe39DXphDWZnBKNZ3HFuJ6bryGJf9A
1/eCI4is85BNwKPemQUYR0xx83UIzDfrghatZP2mOCDDSA2MNg8HNxLTd12LGoQD
tfgX4B7aftzW9Y7GSEDfZ0IKm2NRzgPmCVj6PjVR/iI0lIK4Aq0Z/lDJxxEq3XQ=
=AJM5
-----END PGP SIGNATURE-----
Merge tag 'v4.1-rc6' into drm-next
Linux 4.1-rc6
backmerge 4.1-rc6 as some of the later pull reqs are based on newer bases
and I'd prefer to do the fixup myself.
MI_MODE is saved in the logical context so WaDisableAsyncFlipPerfMode
must be applied using LRIs on gen8.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
INSTPM is saved in the logical context so we should initialize it using
LRIs on gen8. It actually defaults to 1 starting from HSW, but let's
keep the write around anyway.
Also drop the INSTPM_FORCE_ORDERING setup entirely on gen9+ since it's
now a reserved bit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
BXT supports following intermediate link rates for edp:
2.16GHz, 2.43GHz, 3.24GHz, 4.32GHz.
Adding support for programming the intermediate rates.
v2: Adding clock in bxt_clk_div struct and then look for the entry with
required rate (Ville)
v3: 'clock' has the selected value, no need to use link_bw or rate_select
for selecting pll(Ville)
v4: Make bxt_dp_clk_val const and remove size (Ville)
v5: Rebased
v6: Removed setting of vco while rebasing in v5, adding it back
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v4)
Reviewed-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
commit 65ca7514e2
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Mon Feb 9 19:33:22 2015 +0000
drm/i915/skl: Implement WaBarrierPerformanceFixDisable
got misapplied and the code landed in chv_init_workarounds() instead of
the intended skl_init_workarounds(). Move it over to the right place.
Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Simplify intel_hpd_irq_handler() by extracting HPD irq storm detection
to a separate function.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already set this limit for the GGTT.
This is a temporary patch until a full replacement of size_t variables
(inadequate in 32-bit kernel) is in place.
Regression from:
commit a4e0bedca6
Author: Michel Thierry <michel.thierry@intel.com>
Date: Wed Apr 8 12:13:35 2015 +0100
drm/i915: Use complete address space in true PPGTT
v2: Prettify code and explain why this is needed. (Chris)
v3: Don't hide the compilation warning in 32-bit. (Chris)
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Silence the following -Wmaybe-uninitialized warnings and make the code
more clear.
drivers/gpu/drm/i915/intel_display.c: In function ‘__intel_set_mode’:
drivers/gpu/drm/i915/intel_display.c:11844:14: warning: ‘crtc_state’ may be used uninitialized in this function [-Wmaybe-uninitialized]
return state->mode_changed || state->active_changed;
^
drivers/gpu/drm/i915/intel_display.c:11854:25: note: ‘crtc_state’ was declared here
struct drm_crtc_state *crtc_state;
^
drivers/gpu/drm/i915/intel_display.c:11868:6: warning: ‘crtc’ may be used uninitialized in this function [-Wmaybe-uninitialized]
if (crtc != intel_encoder->base.crtc)
^
drivers/gpu/drm/i915/intel_display.c:11853:19: note: ‘crtc’ was declared here
struct drm_crtc *crtc;
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With unified modeset and flip paths introduced recently when switching
to fbcon PSR was being disabled on fb_set_par path but re-enabled on
fb_pan_display one, causing missed screen updates and un unusable
console.
Regression introduced with:
commit bb54662350
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:13:13 2015 +0300
drm/i915: Unify modeset and flip paths of intel_crtc_set_config()
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Without this frontbuffer flip when enabling planes PSR got compromised
and wasn't being enabled waiting forever on the flush that never
arrived.
Another solution would to create a enable_cursor function and split this
frontbuffer flip among the different plane enable and disable functions.
But if necessary this can be done in a follow up work. For now let's
just fix the regression.
It was removed by:
commit 87d4300a7d
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Apr 21 17:12:54 2015 +0300
drm/i915: Move intel_(pre_disable/post_enable)_primary to intel_display.c, and use it there.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The hotplug status is cached in hp_control, and will be passed on to
bottom halves through intel_hpd_irq_handler(), so we can clear the
sticky bits earlier.
While at it, drop the redundant logging of the hotplug status, which
will also be logged by pch_get_hpd_pins().
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Split intel_hpd_irq_handler into platforms specific and platform
agnostic parts. The platform specific parts decode the registers into
information about which hpd pins triggered, and if they were long
pulses. The platform agnostic parts do further processing, such as
interrupt storm mitigation and scheduling bottom halves.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As the hpd loops have been merged together, we don't have to maintain
state for all hpd triggers.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Nothing in the two consecutive loops over hpd pins depends on state in a
larger context than the single hpd pin. If we skip the rest of the loop
on short hpd pulses, we can merge the two loops into one.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In an unfortunate back and forth stepping, retract the earlier change to
reduce indent. This is to make merging the two loops easier. No
functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Multiple positive and negative checks for hpd[i] & hotplug_trigger gets
hard to read. Simplify. This should make follow-up patches merging the
two loops easier. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Print a warning if we fall through the .get_display_clock_speed() function
pointer setup. We end up assuming a 133MHz cdclk which should mean that
at least we avoid any 0 deivisions and whatnot. But this could at least
help remind people that they have to provide this function for new platforms.
v2: Rebased to the latest
v3: Rebased to the latest
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Implement cdclk extraction for g33, 965gm and g4x platforms. The details
came from configdb. Sadly there isn't anything there for other gen3/gen4
chipsets.
So far I've tested this on one ELK where it gave me a HPLL VCO of 5333
MHz and cdclk of 444 MHz which seems perfectly sane for this machine.
v2: Rebased to the latest
v3: Rebased to the latest
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems 852GM/GMV uses a different HPLLCC encoding than the other
85x platforms. For 852GM/GMV cdclk is always 133MHz. Try to detect that
using the PCI revision (sinc the device ID seems useless for that). I'm
not at all sure this is a good idea, but according to the specs it
should work.
v2: Rebased to the latest
v3: Rebased to the latest
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Actually read the HPLLCC register insted of assuming it's 0. Fix the
HPLLCC bit definitions and all the missing ones from the 852GME spec.
852GME, 854 and 855 all seem to match the same HPLLC encoding even
though only some of the values are valid is some of the platforms.
v2: Rebased to the latest
v3: Rebased to the latest
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Printing it for PPGTT VMAs only adds noise since we have defined
view types are only applicable for GGTT.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The orignal code started by storing the actual central frequency (in Hz,
using a uint64_t) in a uint32_t which codes for the register value. That
can't be right.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those functions were the only one in existence when they were
introduced. We now know they are only valid for HSW/BDW.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
abs_diff() properly protects its parameters, so no need for the outer ()
here.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
div_u64() can be either a inline function or a define, but in either
case it's safe to provide expressions as parameters without outer ()
around them.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This part doesn't depend on how we compute the DPLL dividers (p and
p0/p1/p2) and can be reused even if we change the algorithm to do so.
(something that is planned for a followup patch)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä
Imre Deak
Damien Lespiau
Jani Nikula
Dave Airlie
Sonika Jindal
Michel Thierry
Ander Conselvan de Oliveira
Rodrigo Vivi
Tvrtko Ursulin