The MSI doorbell on Apple HW can be any address in the low 4GB range.
However, the MSI write is matched by the PCIe block before hitting the
iommu. It must thus be excluded from the IOVA range that is assigned to any
PCIe device.
Link: https://lore.kernel.org/r/20210929163847.2807812-9-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Including:
- Intel IOMMU Updates fro Lu Baolu:
- Dump DMAR translation structure when DMA fault occurs
- An optimization in the page table manipulation code
- Use second level for GPA->HPA translation
- Various cleanups
- Arm SMMU Updates from Will
- Minor optimisations to SMMUv3 command creation and submission
- Numerous new compatible string for Qualcomm SMMUv2 implementations
- Fixes for the SWIOTLB based implemenation of dma-iommu code for
untrusted devices
- Add support for r8a779a0 to the Renesas IOMMU driver and DT matching
code for r8a77980
- A couple of cleanups and fixes for the Apple DART IOMMU driver
- Make use of generic report_iommu_fault() interface in the AMD IOMMU
driver
- Various smaller fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=waUR
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Intel IOMMU Updates fro Lu Baolu:
- Dump DMAR translation structure when DMA fault occurs
- An optimization in the page table manipulation code
- Use second level for GPA->HPA translation
- Various cleanups
- Arm SMMU Updates from Will
- Minor optimisations to SMMUv3 command creation and submission
- Numerous new compatible string for Qualcomm SMMUv2 implementations
- Fixes for the SWIOTLB based implemenation of dma-iommu code for
untrusted devices
- Add support for r8a779a0 to the Renesas IOMMU driver and DT matching
code for r8a77980
- A couple of cleanups and fixes for the Apple DART IOMMU driver
- Make use of generic report_iommu_fault() interface in the AMD IOMMU
driver
- Various smaller fixes and cleanups
* tag 'iommu-updates-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (35 commits)
iommu/dma: Fix incorrect error return on iommu deferred attach
iommu/dart: Initialize DART_STREAMS_ENABLE
iommu/dma: Use kvcalloc() instead of kvzalloc()
iommu/tegra-smmu: Use devm_bitmap_zalloc when applicable
iommu/dart: Use kmemdup instead of kzalloc and memcpy
iommu/vt-d: Avoid duplicate removing in __domain_mapping()
iommu/vt-d: Convert the return type of first_pte_in_page to bool
iommu/vt-d: Clean up unused PASID updating functions
iommu/vt-d: Delete dev_has_feat callback
iommu/vt-d: Use second level for GPA->HPA translation
iommu/vt-d: Check FL and SL capability sanity in scalable mode
iommu/vt-d: Remove duplicate identity domain flag
iommu/vt-d: Dump DMAR translation structure when DMA fault occurs
iommu/vt-d: Do not falsely log intel_iommu is unsupported kernel option
iommu/arm-smmu-qcom: Request direct mapping for modem device
iommu: arm-smmu-qcom: Add compatible for QCM2290
dt-bindings: arm-smmu: Add compatible for QCM2290 SoC
iommu/arm-smmu-qcom: Add SM6350 SMMU compatible
dt-bindings: arm-smmu: Add compatible for SM6350 SoC
iommu/arm-smmu-v3: Properly handle the return value of arm_smmu_cmdq_build_cmd()
...
The end goal of the current buffer overflow detection work[0] is to gain
full compile-time and run-time coverage of all detectable buffer overflows
seen via array indexing or memcpy(), memmove(), and memset(). The str*()
family of functions already have full coverage.
While much of the work for these changes have been on-going for many
releases (i.e. 0-element and 1-element array replacements, as well as
avoiding false positives and fixing discovered overflows[1]), this series
contains the foundational elements of several related buffer overflow
detection improvements by providing new common helpers and FORTIFY_SOURCE
changes needed to gain the introspection required for compiler visibility
into array sizes. Also included are a handful of already Acked instances
using the helpers (or related clean-ups), with many more waiting at the
ready to be taken via subsystem-specific trees[2]. The new helpers are:
- struct_group() for gaining struct member range introspection.
- memset_after() and memset_startat() for clearing to the end of structures.
- DECLARE_FLEX_ARRAY() for using flex arrays in unions or alone in structs.
Also included is the beginning of the refactoring of FORTIFY_SOURCE to
support memcpy() introspection, fix missing and regressed coverage under
GCC, and to prepare to fix the currently broken Clang support. Finishing
this work is part of the larger series[0], but depends on all the false
positives and buffer overflow bug fixes to have landed already and those
that depend on this series to land.
As part of the FORTIFY_SOURCE refactoring, a set of both a compile-time
and run-time tests are added for FORTIFY_SOURCE and the mem*()-family
functions respectively. The compile time tests have found a legitimate
(though corner-case) bug[6] already.
Please note that the appearance of "panic" and "BUG" in the
FORTIFY_SOURCE refactoring are the result of relocating existing code,
and no new use of those code-paths are expected nor desired.
Finally, there are two tree-wide conversions for 0-element arrays and
flexible array unions to gain sane compiler introspection coverage that
result in no known object code differences.
After this series (and the changes that have now landed via netdev
and usb), we are very close to finally being able to build with
-Warray-bounds and -Wzero-length-bounds. However, due corner cases in
GCC[3] and Clang[4], I have not included the last two patches that turn
on these options, as I don't want to introduce any known warnings to
the build. Hopefully these can be solved soon.
[0] https://lore.kernel.org/lkml/20210818060533.3569517-1-keescook@chromium.org/
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/log/?qt=grep&q=FORTIFY_SOURCE
[2] https://lore.kernel.org/lkml/202108220107.3E26FE6C9C@keescook/
[3] https://lore.kernel.org/lkml/3ab153ec-2798-da4c-f7b1-81b0ac8b0c5b@roeck-us.net/
[4] https://bugs.llvm.org/show_bug.cgi?id=51682
[5] https://lore.kernel.org/lkml/202109051257.29B29745C0@keescook/
[6] https://lore.kernel.org/lkml/20211020200039.170424-1-keescook@chromium.org/
-----BEGIN PGP SIGNATURE-----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=9xbT
-----END PGP SIGNATURE-----
Merge tag 'overflow-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull overflow updates from Kees Cook:
"The end goal of the current buffer overflow detection work[0] is to
gain full compile-time and run-time coverage of all detectable buffer
overflows seen via array indexing or memcpy(), memmove(), and
memset(). The str*() family of functions already have full coverage.
While much of the work for these changes have been on-going for many
releases (i.e. 0-element and 1-element array replacements, as well as
avoiding false positives and fixing discovered overflows[1]), this
series contains the foundational elements of several related buffer
overflow detection improvements by providing new common helpers and
FORTIFY_SOURCE changes needed to gain the introspection required for
compiler visibility into array sizes. Also included are a handful of
already Acked instances using the helpers (or related clean-ups), with
many more waiting at the ready to be taken via subsystem-specific
trees[2].
The new helpers are:
- struct_group() for gaining struct member range introspection
- memset_after() and memset_startat() for clearing to the end of
structures
- DECLARE_FLEX_ARRAY() for using flex arrays in unions or alone in
structs
Also included is the beginning of the refactoring of FORTIFY_SOURCE to
support memcpy() introspection, fix missing and regressed coverage
under GCC, and to prepare to fix the currently broken Clang support.
Finishing this work is part of the larger series[0], but depends on
all the false positives and buffer overflow bug fixes to have landed
already and those that depend on this series to land.
As part of the FORTIFY_SOURCE refactoring, a set of both a
compile-time and run-time tests are added for FORTIFY_SOURCE and the
mem*()-family functions respectively. The compile time tests have
found a legitimate (though corner-case) bug[6] already.
Please note that the appearance of "panic" and "BUG" in the
FORTIFY_SOURCE refactoring are the result of relocating existing code,
and no new use of those code-paths are expected nor desired.
Finally, there are two tree-wide conversions for 0-element arrays and
flexible array unions to gain sane compiler introspection coverage
that result in no known object code differences.
After this series (and the changes that have now landed via netdev and
usb), we are very close to finally being able to build with
-Warray-bounds and -Wzero-length-bounds.
However, due corner cases in GCC[3] and Clang[4], I have not included
the last two patches that turn on these options, as I don't want to
introduce any known warnings to the build. Hopefully these can be
solved soon"
Link: https://lore.kernel.org/lkml/20210818060533.3569517-1-keescook@chromium.org/ [0]
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/log/?qt=grep&q=FORTIFY_SOURCE [1]
Link: https://lore.kernel.org/lkml/202108220107.3E26FE6C9C@keescook/ [2]
Link: https://lore.kernel.org/lkml/3ab153ec-2798-da4c-f7b1-81b0ac8b0c5b@roeck-us.net/ [3]
Link: https://bugs.llvm.org/show_bug.cgi?id=51682 [4]
Link: https://lore.kernel.org/lkml/202109051257.29B29745C0@keescook/ [5]
Link: https://lore.kernel.org/lkml/20211020200039.170424-1-keescook@chromium.org/ [6]
* tag 'overflow-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (30 commits)
fortify: strlen: Avoid shadowing previous locals
compiler-gcc.h: Define __SANITIZE_ADDRESS__ under hwaddress sanitizer
treewide: Replace 0-element memcpy() destinations with flexible arrays
treewide: Replace open-coded flex arrays in unions
stddef: Introduce DECLARE_FLEX_ARRAY() helper
btrfs: Use memset_startat() to clear end of struct
string.h: Introduce memset_startat() for wiping trailing members and padding
xfrm: Use memset_after() to clear padding
string.h: Introduce memset_after() for wiping trailing members/padding
lib: Introduce CONFIG_MEMCPY_KUNIT_TEST
fortify: Add compile-time FORTIFY_SOURCE tests
fortify: Allow strlen() and strnlen() to pass compile-time known lengths
fortify: Prepare to improve strnlen() and strlen() warnings
fortify: Fix dropped strcpy() compile-time write overflow check
fortify: Explicitly disable Clang support
fortify: Move remaining fortify helpers into fortify-string.h
lib/string: Move helper functions out of string.c
compiler_types.h: Remove __compiletime_object_size()
cm4000_cs: Use struct_group() to zero struct cm4000_dev region
can: flexcan: Use struct_group() to zero struct flexcan_regs regions
...
by confidential computing solutions to query different aspects of the
system. The intent behind it is to unify testing of such aspects instead
of having each confidential computing solution add its own set of tests
to code paths in the kernel, leading to an unwieldy mess.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEzv7L6UO9uDPlPSfHEsHwGGHeVUoFAmF/uLUACgkQEsHwGGHe
VUqGbQ/+LOmz8hmL5vtbXw/lVonCSBRKI2KVefnN2VtQ3rjtCq8HlNoq/hAdi15O
WntABFV8u4daNAcssp+H/p+c8Mt/NzQa60TRooC5ZIynSOCj4oZQxTWjcnR4Qxrf
oABy4sp09zNW31qExtTVTwPC/Ejzv4hA0Vqt9TLQOSxp7oYVYKeDJNp79VJK64Yz
Ky7epgg8Pauk0tAT76ATR4kyy9PLGe4/Ry0bOtAptO4NShL1RyRgI0ywUmptJHSw
FV/MnoexdAs4V8+4zPwyOkf8YMDnhbJcvFcr7Yd9AEz2q9Z1wKCgi1M3aZIoW8lV
YMXECMGe9DfxmEJbnP5zbnL6eF32x+tbq+fK8Ye4V2fBucpWd27zkcTXjoP+Y+zH
NLg+9QykR9QCH75YCOXcAg1Q5hSmc4DaWuJymKjT+W7MKs89ywjq+ybIBpLBHbQe
uN9FM/CEKXx8nQwpNQc7mdUE5sZeCQ875028RaLbLx3/b6uwT6rBlNJfxl/uxmcZ
iF1kG7Cx4uO+7G1a9EWgxtWiJQ8GiZO7PMCqEdwIymLIrlNksAk7nX2SXTuH5jIZ
YDuBj/Xz2UUVWYFm88fV5c4ogiFlm9Jeo140Zua/BPdDJd2VOP013rYxzFE/rVSF
SM2riJxCxkva8Fb+8TNiH42AMhPMSpUt1Nmd1H2rcEABRiT83Ow=
=Na0U
-----END PGP SIGNATURE-----
Merge tag 'x86_cc_for_v5.16_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull generic confidential computing updates from Borislav Petkov:
"Add an interface called cc_platform_has() which is supposed to be used
by confidential computing solutions to query different aspects of the
system.
The intent behind it is to unify testing of such aspects instead of
having each confidential computing solution add its own set of tests
to code paths in the kernel, leading to an unwieldy mess"
* tag 'x86_cc_for_v5.16_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
treewide: Replace the use of mem_encrypt_active() with cc_platform_has()
x86/sev: Replace occurrences of sev_es_active() with cc_platform_has()
x86/sev: Replace occurrences of sev_active() with cc_platform_has()
x86/sme: Replace occurrences of sme_active() with cc_platform_has()
powerpc/pseries/svm: Add a powerpc version of cc_platform_has()
x86/sev: Add an x86 version of cc_platform_has()
arch/cc: Introduce a function to check for confidential computing features
x86/ioremap: Selectively build arch override encryption functions
scsi_dma_map() was reporting a failure during boot on an AMD machine
with the IOMMU enabled.
scsi_dma_map failed: request for 36 bytes!
The issue was tracked down to a mistake in logic: should not return
an error if iommu_deferred_attach() returns zero.
Reported-by: Marshall Midden <marshallmidden@gmail.com>
Fixes: dabb16f672 ("iommu/dma: return error code from iommu_dma_map_sg()")
Link: https://lore.kernel.org/all/CAD2CkAWjS8=kKwEEN4cgVNjyFORUibzEiCUA-X+SMtbo0JoMmA@mail.gmail.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20211027174757.119755-1-logang@deltatee.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
DART has an additional global register to control which streams are
isolated. This register is a bit redundant since DART_TCR can already
be used to control isolation and is usually initialized to DART_STREAM_ALL
by the time we get control. Some DARTs (namely the one used for the audio
controller) however have some streams disabled initially. Make sure those
work by initializing DART_STREAMS_ENABLE during reset.
Reported-by: Martin Povišer <povik@protonmail.com>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20211019162253.45919-1-sven@svenpeter.dev
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The __domain_mapping() always removes the pages in the range from
'iov_pfn' to 'end_pfn', but the 'end_pfn' is always the last pfn
of the range that the caller wants to map.
This would introduce too many duplicated removing and leads the
map operation take too long, for example:
Map iova=0x100000,nr_pages=0x7d61800
iov_pfn: 0x100000, end_pfn: 0x7e617ff
iov_pfn: 0x140000, end_pfn: 0x7e617ff
iov_pfn: 0x180000, end_pfn: 0x7e617ff
iov_pfn: 0x1c0000, end_pfn: 0x7e617ff
iov_pfn: 0x200000, end_pfn: 0x7e617ff
...
it takes about 50ms in total.
We can reduce the cost by recalculate the 'end_pfn' and limit it
to the boundary of the end of this pte page.
Map iova=0x100000,nr_pages=0x7d61800
iov_pfn: 0x100000, end_pfn: 0x13ffff
iov_pfn: 0x140000, end_pfn: 0x17ffff
iov_pfn: 0x180000, end_pfn: 0x1bffff
iov_pfn: 0x1c0000, end_pfn: 0x1fffff
iov_pfn: 0x200000, end_pfn: 0x23ffff
...
it only need 9ms now.
This also removes a meaningless BUG_ON() in __domain_mapping().
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Tested-by: Liujunjie <liujunjie23@huawei.com>
Link: https://lore.kernel.org/r/20211008000433.1115-1-longpeng2@huawei.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211014053839.727419-10-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
update_pasid() and its call chain are currently unused in the tree because
Thomas disabled the ENQCMD feature. The feature will be re-enabled shortly
using a different approach and update_pasid() and its call chain will not
be used in the new approach.
Remove the useless functions.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210920192349.2602141-1-fenghua.yu@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211014053839.727419-8-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The IOMMU VT-d implementation uses the first level for GPA->HPA translation
by default. Although both the first level and the second level could handle
the DMA translation, they're different in some way. For example, the second
level translation has separate controls for the Access/Dirty page tracking.
With the first level translation, there's no such control. On the other
hand, the second level translation has the page-level control for forcing
snoop, but the first level only has global control with pasid granularity.
This uses the second level for GPA->HPA translation so that we can provide
a consistent hardware interface for use cases like dirty page tracking for
live migration.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20210926114535.923263-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20211014053839.727419-6-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
An iommu domain could be allocated and mapped before it's attached to any
device. This requires that in scalable mode, when the domain is allocated,
the format (FL or SL) of the page table must be determined. In order to
achieve this, the platform should support consistent SL or FL capabilities
on all IOMMU's. This adds a check for this and aborts IOMMU probing if it
doesn't meet this requirement.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20210926114535.923263-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20211014053839.727419-5-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When the dmar translation fault happens, the kernel prints a single line
fault reason with corresponding hexadecimal code defined in the Intel VT-d
specification.
Currently, when user wants to debug the translation fault in detail,
debugfs is used for dumping the dmar_translation_struct, which is not
available when the kernel failed to boot.
Dump the DMAR translation structure, pagewalk the IO page table and print
the page table entry when the fault happens.
This takes effect only when CONFIG_DMAR_DEBUG is enabled.
Signed-off-by: Kyung Min Park <kyung.min.park@intel.com>
Link: https://lore.kernel.org/r/20210815203845.31287-1-kyung.min.park@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211014053839.727419-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Handling of intel_iommu kernel command line option should return "true" to
indicate option is valid and so avoid logging it as unknown by the core
parsing code.
Also log unknown sub-options at the notice level to let user know of
potential typos or similar.
Reported-by: Eero Tamminen <eero.t.tamminen@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://lore.kernel.org/r/20210831112947.310080-1-tvrtko.ursulin@linux.intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211014053839.727419-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
My previous bugfix ended up making things worse for the QCOM IOMMU
driver when it forgot to add the Kconfig symbol that is getting used to
control the compilation of the SMMU implementation specific code
for Qualcomm.
Fixes: 424953cf3c ("qcom_scm: hide Kconfig symbol")
Reported-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reported-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/lkml/20211010023350.978638-1-dmitry.baryshkov@linaro.org/
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The
fix we agreed on in the end is to make this symbol selected by any
driver using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in v5.15.
There is a small merge conflict against an earlier partial fix for the
QCOM_SCM dependency problems.
Finally, the branch also includes a small unrelated build fix for NOMMU
architectures.
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=187C
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fixes from Arnd Bergmann:
"There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The fix we
agreed on in the end is to make this symbol selected by any driver
using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in
v5.15.
Finally, the branch also includes a small unrelated build fix for
NOMMU architectures"
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
* tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic/io.h: give stub iounmap() on !MMU same prototype as elsewhere
qcom_scm: hide Kconfig symbol
firmware: include drivers/firmware/Kconfig unconditionally
The SID configuration requirement for Modem on SC7280 is similar to the
ones found on SC7180/SDM845 SoCs. So, add the SC7280 modem compatible to
the list to defer the programming of the modem SIDs to the kernel.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1631886935-14691-5-git-send-email-sibis@codeaurora.org
Signed-off-by: Will Deacon <will@kernel.org>
Now that SCM can be a loadable module, we have to add another
dependency to avoid link failures when ipa or adreno-gpu are
built-in:
aarch64-linux-ld: drivers/net/ipa/ipa_main.o: in function `ipa_probe':
ipa_main.c:(.text+0xfc4): undefined reference to `qcom_scm_is_available'
ld.lld: error: undefined symbol: qcom_scm_is_available
>>> referenced by adreno_gpu.c
>>> gpu/drm/msm/adreno/adreno_gpu.o:(adreno_zap_shader_load) in archive drivers/built-in.a
This can happen when CONFIG_ARCH_QCOM is disabled and we don't select
QCOM_MDT_LOADER, but some other module selects QCOM_SCM. Ideally we'd
use a similar dependency here to what we have for QCOM_RPROC_COMMON,
but that causes dependency loops from other things selecting QCOM_SCM.
This appears to be an endless problem, so try something different this
time:
- CONFIG_QCOM_SCM becomes a hidden symbol that nothing 'depends on'
but that is simply selected by all of its users
- All the stubs in include/linux/qcom_scm.h can go away
- arm-smccc.h needs to provide a stub for __arm_smccc_smc() to
allow compile-testing QCOM_SCM on all architectures.
- To avoid a circular dependency chain involving RESET_CONTROLLER
and PINCTRL_SUNXI, drop the 'select RESET_CONTROLLER' statement.
According to my testing this still builds fine, and the QCOM
platform selects this symbol already.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add compatible for QCM2290 SMMU to use the Qualcomm Technologies, Inc.
specific implementation.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1633096832-7762-1-git-send-email-loic.poulain@linaro.org
[will: Sort by alphabetical order, add commit message]
Signed-off-by: Will Deacon <will@kernel.org>
1. Build command CMD_SYNC cannot fail. So the return value can be ignored.
2. The arm_smmu_cmdq_build_cmd() almost never fails, the addition of
"unlikely()" can optimize the instruction pipeline.
3. Check the return value in arm_smmu_cmdq_batch_add().
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210818080452.2079-2-thunder.leizhen@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Pre-zeroing the batched commands structure is inefficient, as individual
commands are zeroed later in arm_smmu_cmdq_build_cmd(). Therefore, only
the member 'num' needs to be initialized to 0.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/20210817113411.1962-1-thunder.leizhen@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Replace uses of mem_encrypt_active() with calls to cc_platform_has() with
the CC_ATTR_MEM_ENCRYPT attribute.
Remove the implementation of mem_encrypt_active() across all arches.
For s390, since the default implementation of the cc_platform_has()
matches the s390 implementation of mem_encrypt_active(), cc_platform_has()
does not need to be implemented in s390 (the config option
ARCH_HAS_CC_PLATFORM is not set).
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210928191009.32551-9-bp@alien8.de
Replace uses of sme_active() with the more generic cc_platform_has()
using CC_ATTR_HOST_MEM_ENCRYPT. If future support is added for other
memory encryption technologies, the use of CC_ATTR_HOST_MEM_ENCRYPT
can be updated, as required.
This also replaces two usages of sev_active() that are really geared
towards detecting if SME is active.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210928191009.32551-6-bp@alien8.de
This patch makes iommu/amd call report_iommu_fault() when an I/O page
fault occurs, which has two effects:
1) It allows device drivers to register a callback to be notified of
I/O page faults, via the iommu_set_fault_handler() API.
2) It triggers the io_page_fault tracepoint in report_iommu_fault()
when an I/O page fault occurs.
The latter point is the main aim of this patch, as it allows
rasdaemon-like daemons to be notified of I/O page faults, and to
possibly initiate corrective action in response.
A number of other IOMMU drivers already use report_iommu_fault(), and
I/O page faults on those IOMMUs therefore already trigger this
tracepoint -- but this isn't yet the case for AMD-Vi and Intel DMAR.
The AMD IOMMU specification suggests that the bit in an I/O page fault
event log entry that signals whether an I/O page fault was for a read
request or for a write request is only meaningful when the faulting
access was to a present page, but some testing on a Ryzen 3700X suggests
that this bit encodes the correct value even for I/O page faults to
non-present pages, and therefore, this patch passes the R/W information
up the stack even for I/O page faults to non-present pages.
Signed-off-by: Lennert Buytenhek <buytenh@arista.com>
Link: https://lore.kernel.org/r/YVLyBW97vZLpOaAp@wantstofly.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Pass the non-aligned size to __iommu_dma_map when using swiotlb bounce
buffers in iommu_dma_map_page, to account for min_align_mask.
To deal with granule alignment, __iommu_dma_map maps iova_align(size +
iova_off) bytes starting at phys - iova_off. If iommu_dma_map_page
passes aligned size when using swiotlb, then this becomes
iova_align(iova_align(orig_size) + iova_off). Normally iova_off will be
zero when using swiotlb. However, this is not the case for devices that
set min_align_mask. When iova_off is non-zero, __iommu_dma_map ends up
mapping an extra page at the end of the buffer. Beyond just being a
security issue, the extra page is not cleaned up by __iommu_dma_unmap.
This causes problems when the IOVA is reused, due to collisions in the
iommu driver. Just passing the original size is sufficient, since
__iommu_dma_map will take care of granule alignment.
Fixes: 1f221a0d0d ("swiotlb: respect min_align_mask")
Signed-off-by: David Stevens <stevensd@chromium.org>
Link: https://lore.kernel.org/r/20210929023300.335969-8-stevensd@google.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add an argument to swiotlb_tbl_map_single that specifies the desired
alignment of the allocated buffer. This is used by dma-iommu to ensure
the buffer is aligned to the iova granule size when using swiotlb with
untrusted sub-granule mappings. This addresses an issue where adjacent
slots could be exposed to the untrusted device if IO_TLB_SIZE < iova
granule < PAGE_SIZE.
Signed-off-by: David Stevens <stevensd@chromium.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210929023300.335969-7-stevensd@google.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Introduce a new dev_use_swiotlb function to guard swiotlb code, instead
of overloading dev_is_untrusted. This allows CONFIG_SWIOTLB to be
checked more broadly, so the swiotlb related code can be removed more
aggressively.
Signed-off-by: David Stevens <stevensd@chromium.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210929023300.335969-6-stevensd@google.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Fold the _swiotlb helper functions into the respective _page functions,
since recent fixes have moved all logic from the _page functions to the
_swiotlb functions.
Signed-off-by: David Stevens <stevensd@chromium.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20210929023300.335969-5-stevensd@google.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Calling the iommu_dma_sync_*_for_cpu functions during unmap can cause
two copies out of the swiotlb buffer. Do the arch sync directly in
__iommu_dma_unmap_swiotlb instead to avoid this. This makes the call to
iommu_dma_sync_sg_for_cpu for untrusted devices in iommu_dma_unmap_sg no
longer necessary, so move that invocation later in the function.
Signed-off-by: David Stevens <stevensd@chromium.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20210929023300.335969-4-stevensd@google.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When calling arch_sync_dma, we need to pass it the memory that's
actually being used for dma. When using swiotlb bounce buffers, this is
the bounce buffer. Move arch_sync_dma into the __iommu_dma_map_swiotlb
helper, so it can use the bounce buffer address if necessary.
Now that iommu_dma_map_sg delegates to a function which takes care of
architectural syncing in the untrusted device case, the call to
iommu_dma_sync_sg_for_device can be moved so it only occurs for trusted
devices. Doing the sync for untrusted devices before mapping never
really worked, since it needs to be able to target swiotlb buffers.
This also moves the architectural sync to before the call to
__iommu_dma_map, to guarantee that untrusted devices can't see stale
data they shouldn't see.
Fixes: 82612d66d5 ("iommu: Allow the iommu/dma api to use bounce buffers")
Signed-off-by: David Stevens <stevensd@chromium.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20210929023300.335969-3-stevensd@google.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The is_swiotlb_buffer function takes the physical address of the swiotlb
buffer, not the physical address of the original buffer. The sglist
contains the physical addresses of the original buffer, so for the
sync_sg functions to work properly when a bounce buffer might have been
used, we need to use iommu_iova_to_phys to look up the physical address.
This is what sync_single does, so call that function on each sglist
segment.
The previous code mostly worked because swiotlb does the transfer on map
and unmap. However, any callers which use DMA_ATTR_SKIP_CPU_SYNC with
sglists or which call sync_sg would not have had anything copied to the
bounce buffer.
Fixes: 82612d66d5 ("iommu: Allow the iommu/dma api to use bounce buffers")
Signed-off-by: David Stevens <stevensd@chromium.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210929023300.335969-2-stevensd@google.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
clang-14 notices that a comparison is never true when
CONFIG_PHYS_ADDR_T_64BIT is disabled:
drivers/iommu/mtk_iommu.c:553:34: error: result of comparison of constant 5368709120 with expression of type 'phys_addr_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (dom->data->enable_4GB && pa >= MTK_IOMMU_4GB_MODE_REMAP_BASE)
~~ ^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Add an explicit check for the type of the variable to skip the check
and the warning in that case.
Fixes: b4dad40e4f ("iommu/mediatek: Adjust the PA for the 4GB Mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20210927121857.941160-1-arnd@kernel.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
sid2groups keeps track of which stream id combinations belong to a
iommu_group to assign those correctly to devices.
When a iommu_group is freed a stale pointer will however remain in
sid2groups. This prevents devices with the same stream id combination
to ever be attached again (see below).
Fix that by creating a shadow copy of the stream id configuration
when a group is allocated for the first time and clear the sid2group
entry when that group is freed.
# echo 1 >/sys/bus/pci/devices/0000\:03\:00.0/remove
pci 0000:03:00.0: Removing from iommu group 1
# echo 1 >/sys/bus/pci/rescan
[...]
pci 0000:03:00.0: BAR 0: assigned [mem 0x6a0000000-0x6a000ffff 64bit pref]
pci 0000:03:00.0: BAR 2: assigned [mem 0x6a0010000-0x6a001ffff 64bit pref]
pci 0000:03:00.0: BAR 6: assigned [mem 0x6c0100000-0x6c01007ff pref]
tg3 0000:03:00.0: Failed to add to iommu group 1: -2
[...]
Fixes: 46d1fb072e ("iommu/dart: Add DART iommu driver")
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Tested-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210924134502.15589-1-sven@svenpeter.dev
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add r8a77980 (R-Car V3H) to the list of supported devices. The hardware
is the same as on already-supportred V3M and other R-Car Gen3 chips.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20210923191115.22864-1-nikita.yoush@cogentembedded.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
719a193356 ("iommu/vt-d: Tweak the description of a DMA fault") changed
the DMA fault reason from hex to decimal. It also added "0x" prefixes to
the PCI bus/device, e.g.,
- DMAR: [INTR-REMAP] Request device [00:00.5]
+ DMAR: [INTR-REMAP] Request device [0x00:0x00.5]
These no longer match dev_printk() and other similar messages in
dmar_match_pci_path() and dmar_acpi_insert_dev_scope().
Drop the "0x" prefixes from the bus and device addresses.
Fixes: 719a193356 ("iommu/vt-d: Tweak the description of a DMA fault")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20210903193711.483999-1-helgaas@kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210922054726.499110-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
apple_dart_tlb_flush_{all,walk} expect to get a struct apple_dart_domain
but instead get a struct iommu_domain right now. This breaks those two
functions and can lead to kernel panics like the one below.
DART can only invalidate the entire TLB and apple_dart_iotlb_sync will
already flush everything. There's no need to do that again inside those
two functions. Let's just drop them.
pci 0000:03:00.0: Removing from iommu group 1
Unable to handle kernel paging request at virtual address 0000000100000023
[...]
Call trace:
_raw_spin_lock_irqsave+0x54/0xbc
apple_dart_hw_stream_command.constprop.0+0x2c/0x130
apple_dart_tlb_flush_all+0x48/0x90
free_io_pgtable_ops+0x40/0x70
apple_dart_domain_free+0x2c/0x44
iommu_group_release+0x68/0xac
kobject_cleanup+0x4c/0x1fc
kobject_cleanup+0x14c/0x1fc
kobject_put+0x64/0x84
iommu_group_remove_device+0x110/0x180
iommu_release_device+0x50/0xa0
[...]
Fixes: 46d1fb072e ("iommu/dart: Add DART iommu driver")
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210921153934.35647-1-sven@svenpeter.dev
Signed-off-by: Joerg Roedel <jroedel@suse.de>
IOVA cookies are now got and put by core code, so we no longer need to
export these to modular drivers. The export for getting MSI cookies
stays, since VFIO can still be a module, but it was already relying on
someone else putting them, so that aspect is unaffected.
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/ef89db54a27df7d8bc0af094c7d7b204fd61774c.1631531973.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The addition of the DART driver crossed over with moving IOVA cookie
management into core code; clean up the now-unnecessary remnants here.
Acked-by: Sven Peter <sven@svenpeter.dev>
Tested-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/edb72b4965baa8999dd70b8294785d6deebd4183.1631531973.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add support for r8a779a0 (R-Car V3U). The IPMMU hardware design
of this SoC differs than others. So, add a new ipmmu_features for it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210907083020.907648-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.
Use struct_group() in struct ivhd_entry around members ext and hidh, so
they can be referenced together. This will allow memcpy() and sizeof()
to more easily reason about sizes, improve readability, and avoid future
warnings about writing beyond the end of ext.
"pahole" shows no size nor member offset changes to struct ivhd_entry.
"objdump -d" shows no object code changes.
Cc: Will Deacon <will@kernel.org>
Cc: iommu@lists.linux-foundation.org
Acked-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
vduse driver supporting blk
virtio-vsock support for end of record with SEQPACKET
vdpa: mac and mq support for ifcvf and mlx5
vdpa: management netlink for ifcvf
virtio-i2c, gpio dt bindings
misc fixes, cleanups
NB: when merging this with
b542e383d8 ("eventfd: Make signal recursion protection a task bit")
from Linus' tree, replace eventfd_signal_count with
eventfd_signal_allowed, and drop the export of eventfd_wake_count from
("eventfd: Export eventfd_wake_count to modules").
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmE1+awPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpt6EIAJy0qrc62lktNA0IiIVJSLbUbTMmFj8MzkGR
8UxZdhpjWqBPJPyaOuNeksAqTGm/UAPEYx3C2c95Jhej7anFpy7dbCtIXcPHLJME
DjcJg+EDrlNCj8m0FcsHpHWsFzPMERJpyEZNxgB5WazQbv+yWhGrg2FN5DCnF0Ro
ZFYeKSVty148pQ0nHl8X0JM2XMtqit+O+LvKN2HQZ+fubh7BCzMxzkHY0QLHIzUS
UeZqd3Qm8YcbqnlX38P5D6k+NPiTEgknmxaBLkPxg6H3XxDAmaIRFb8Ldd1rsgy1
zTLGDiSGpVDIpawRnuEAzqJThV3Y5/MVJ1WD+mDYQ96tmhfp+KY=
=DBH/
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
- vduse driver ("vDPA Device in Userspace") supporting emulated virtio
block devices
- virtio-vsock support for end of record with SEQPACKET
- vdpa: mac and mq support for ifcvf and mlx5
- vdpa: management netlink for ifcvf
- virtio-i2c, gpio dt bindings
- misc fixes and cleanups
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (39 commits)
Documentation: Add documentation for VDUSE
vduse: Introduce VDUSE - vDPA Device in Userspace
vduse: Implement an MMU-based software IOTLB
vdpa: Support transferring virtual addressing during DMA mapping
vdpa: factor out vhost_vdpa_pa_map() and vhost_vdpa_pa_unmap()
vdpa: Add an opaque pointer for vdpa_config_ops.dma_map()
vhost-iotlb: Add an opaque pointer for vhost IOTLB
vhost-vdpa: Handle the failure of vdpa_reset()
vdpa: Add reset callback in vdpa_config_ops
vdpa: Fix some coding style issues
file: Export receive_fd() to modules
eventfd: Export eventfd_wake_count to modules
iova: Export alloc_iova_fast() and free_iova_fast()
virtio-blk: remove unneeded "likely" statements
virtio-balloon: Use virtio_find_vqs() helper
vdpa: Make use of PFN_PHYS/PFN_UP/PFN_DOWN helper macro
vsock_test: update message bounds test for MSG_EOR
af_vsock: rename variables in receive loop
virtio/vsock: support MSG_EOR bit processing
vhost/vsock: support MSG_EOR bit processing
...
Including:
- Intel VT-d:
- PASID leakage in intel_svm_unbind_mm();
- Deadlock in intel_svm_drain_prq().
- AMD IOMMU: Fixes for an unhandled page-fault bug when AVIC is used
for a KVM guest.
- Make CONFIG_IOMMU_DEFAULT_DMA_LAZY architecture instead of IOMMU
driver dependent
-----BEGIN PGP SIGNATURE-----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=/POW
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v5.15-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Intel VT-d:
- PASID leakage in intel_svm_unbind_mm()
- Deadlock in intel_svm_drain_prq()
- AMD IOMMU: Fixes for an unhandled page-fault bug when AVIC is used
for a KVM guest.
- Make CONFIG_IOMMU_DEFAULT_DMA_LAZY architecture instead of IOMMU
driver dependent
* tag 'iommu-fixes-v5.15-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu: Clarify default domain Kconfig
iommu/vt-d: Fix a deadlock in intel_svm_drain_prq()
iommu/vt-d: Fix PASID leak in intel_svm_unbind_mm()
iommu/amd: Remove iommu_init_ga()
iommu/amd: Relocate GAMSup check to early_enable_iommus
Although strictly it is the AMD and Intel drivers which have an existing
expectation of lazy behaviour by default, it ends up being rather
unintuitive to describe this literally in Kconfig. Express it instead as
an architecture dependency, to clarify that it is a valid config-time
decision. The end result is the same since virtio-iommu doesn't support
lazy mode and thus falls back to strict at runtime regardless.
The per-architecture disparity is a matter of historical expectations:
the AMD and Intel drivers have been lazy by default since 2008, and
changing that gets noticed by people asking where their I/O throughput
has gone. Conversely, Arm-based systems with their wider assortment of
IOMMU drivers mostly only support strict mode anyway; only the Arm SMMU
drivers have later grown support for passthrough and lazy mode, for
users who wanted to explicitly trade off isolation for performance.
These days, reducing the default level of isolation in a way which may
go unnoticed by users who expect otherwise hardly seems worth risking
for the sake of one line of Kconfig, so here's where we are.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/69a0c6f17b000b54b8333ee42b3124c1d5a869e2.1631105737.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
pasid_mutex and dev->iommu->param->lock are held while unbinding mm is
flushing IO page fault workqueue and waiting for all page fault works to
finish. But an in-flight page fault work also need to hold the two locks
while unbinding mm are holding them and waiting for the work to finish.
This may cause an ABBA deadlock issue as shown below:
idxd 0000:00:0a.0: unbind PASID 2
======================================================
WARNING: possible circular locking dependency detected
5.14.0-rc7+ #549 Not tainted [ 186.615245] ----------
dsa_test/898 is trying to acquire lock:
ffff888100d854e8 (¶m->lock){+.+.}-{3:3}, at:
iopf_queue_flush_dev+0x29/0x60
but task is already holding lock:
ffffffff82b2f7c8 (pasid_mutex){+.+.}-{3:3}, at:
intel_svm_unbind+0x34/0x1e0
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (pasid_mutex){+.+.}-{3:3}:
__mutex_lock+0x75/0x730
mutex_lock_nested+0x1b/0x20
intel_svm_page_response+0x8e/0x260
iommu_page_response+0x122/0x200
iopf_handle_group+0x1c2/0x240
process_one_work+0x2a5/0x5a0
worker_thread+0x55/0x400
kthread+0x13b/0x160
ret_from_fork+0x22/0x30
-> #1 (¶m->fault_param->lock){+.+.}-{3:3}:
__mutex_lock+0x75/0x730
mutex_lock_nested+0x1b/0x20
iommu_report_device_fault+0xc2/0x170
prq_event_thread+0x28a/0x580
irq_thread_fn+0x28/0x60
irq_thread+0xcf/0x180
kthread+0x13b/0x160
ret_from_fork+0x22/0x30
-> #0 (¶m->lock){+.+.}-{3:3}:
__lock_acquire+0x1134/0x1d60
lock_acquire+0xc6/0x2e0
__mutex_lock+0x75/0x730
mutex_lock_nested+0x1b/0x20
iopf_queue_flush_dev+0x29/0x60
intel_svm_drain_prq+0x127/0x210
intel_svm_unbind+0xc5/0x1e0
iommu_sva_unbind_device+0x62/0x80
idxd_cdev_release+0x15a/0x200 [idxd]
__fput+0x9c/0x250
____fput+0xe/0x10
task_work_run+0x64/0xa0
exit_to_user_mode_prepare+0x227/0x230
syscall_exit_to_user_mode+0x2c/0x60
do_syscall_64+0x48/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
other info that might help us debug this:
Chain exists of:
¶m->lock --> ¶m->fault_param->lock --> pasid_mutex
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(pasid_mutex);
lock(¶m->fault_param->lock);
lock(pasid_mutex);
lock(¶m->lock);
*** DEADLOCK ***
2 locks held by dsa_test/898:
#0: ffff888100cc1cc0 (&group->mutex){+.+.}-{3:3}, at:
iommu_sva_unbind_device+0x53/0x80
#1: ffffffff82b2f7c8 (pasid_mutex){+.+.}-{3:3}, at:
intel_svm_unbind+0x34/0x1e0
stack backtrace:
CPU: 2 PID: 898 Comm: dsa_test Not tainted 5.14.0-rc7+ #549
Hardware name: Intel Corporation Kabylake Client platform/KBL S
DDR4 UD IMM CRB, BIOS KBLSE2R1.R00.X050.P01.1608011715 08/01/2016
Call Trace:
dump_stack_lvl+0x5b/0x74
dump_stack+0x10/0x12
print_circular_bug.cold+0x13d/0x142
check_noncircular+0xf1/0x110
__lock_acquire+0x1134/0x1d60
lock_acquire+0xc6/0x2e0
? iopf_queue_flush_dev+0x29/0x60
? pci_mmcfg_read+0xde/0x240
__mutex_lock+0x75/0x730
? iopf_queue_flush_dev+0x29/0x60
? pci_mmcfg_read+0xfd/0x240
? iopf_queue_flush_dev+0x29/0x60
mutex_lock_nested+0x1b/0x20
iopf_queue_flush_dev+0x29/0x60
intel_svm_drain_prq+0x127/0x210
? intel_pasid_tear_down_entry+0x22e/0x240
intel_svm_unbind+0xc5/0x1e0
iommu_sva_unbind_device+0x62/0x80
idxd_cdev_release+0x15a/0x200
pasid_mutex protects pasid and svm data mapping data. It's unnecessary
to hold pasid_mutex while flushing the workqueue. To fix the deadlock
issue, unlock pasid_pasid during flushing the workqueue to allow the works
to be handled.
Fixes: d5b9e4bfe0 ("iommu/vt-d: Report prq to io-pgfault framework")
Reported-and-tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: https://lore.kernel.org/r/20210826215918.4073446-1-fenghua.yu@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210828070622.2437559-3-baolu.lu@linux.intel.com
[joro: Removed timing information from kernel log messages]
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The mm->pasid will be used in intel_svm_free_pasid() after load_pasid()
during unbinding mm. Clearing it in load_pasid() will cause PASID cannot
be freed in intel_svm_free_pasid().
Additionally mm->pasid was updated already before load_pasid() during pasid
allocation. No need to update it again in load_pasid() during binding mm.
Don't update mm->pasid to avoid the issues in both binding mm and unbinding
mm.
Fixes: 4048377414 ("iommu/vt-d: Use iommu_sva_alloc(free)_pasid() helpers")
Reported-and-tested-by: Dave Jiang <dave.jiang@intel.com>
Co-developed-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: https://lore.kernel.org/r/20210826215918.4073446-1-fenghua.yu@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210828070622.2437559-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Since the function has been simplified and only call iommu_init_ga_log(),
remove the function and replace with iommu_init_ga_log() instead.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20210820202957.187572-4-suravee.suthikulpanit@amd.com
Fixes: 8bda0cfbdc ("iommu/amd: Detect and initialize guest vAPIC log")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Currently, iommu_init_ga() checks and disables IOMMU VAPIC support
(i.e. AMD AVIC support in IOMMU) when GAMSup feature bit is not set.
However it forgets to clear IRQ_POSTING_CAP from the previously set
amd_iommu_irq_ops.capability.
This triggers an invalid page fault bug during guest VM warm reboot
if AVIC is enabled since the irq_remapping_cap(IRQ_POSTING_CAP) is
incorrectly set, and crash the system with the following kernel trace.
BUG: unable to handle page fault for address: 0000000000400dd8
RIP: 0010:amd_iommu_deactivate_guest_mode+0x19/0xbc
Call Trace:
svm_set_pi_irte_mode+0x8a/0xc0 [kvm_amd]
? kvm_make_all_cpus_request_except+0x50/0x70 [kvm]
kvm_request_apicv_update+0x10c/0x150 [kvm]
svm_toggle_avic_for_irq_window+0x52/0x90 [kvm_amd]
svm_enable_irq_window+0x26/0xa0 [kvm_amd]
vcpu_enter_guest+0xbbe/0x1560 [kvm]
? avic_vcpu_load+0xd5/0x120 [kvm_amd]
? kvm_arch_vcpu_load+0x76/0x240 [kvm]
? svm_get_segment_base+0xa/0x10 [kvm_amd]
kvm_arch_vcpu_ioctl_run+0x103/0x590 [kvm]
kvm_vcpu_ioctl+0x22a/0x5d0 [kvm]
__x64_sys_ioctl+0x84/0xc0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes by moving the initializing of AMD IOMMU interrupt remapping mode
(amd_iommu_guest_ir) earlier before setting up the
amd_iommu_irq_ops.capability with appropriate IRQ_POSTING_CAP flag.
[joro: Squashed the two patches and limited
check_features_on_all_iommus() to CONFIG_IRQ_REMAP
to fix a compile warning.]
Signed-off-by: Wei Huang <wei.huang2@amd.com>
Co-developed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20210820202957.187572-2-suravee.suthikulpanit@amd.com
Link: https://lore.kernel.org/r/20210820202957.187572-3-suravee.suthikulpanit@amd.com
Fixes: 8bda0cfbdc ("iommu/amd: Detect and initialize guest vAPIC log")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Export alloc_iova_fast() and free_iova_fast() so that
some modules can make use of the per-CPU cache to get
rid of rbtree spinlock in alloc_iova() and free_iova()
during IOVA allocation.
Signed-off-by: Xie Yongji <xieyongji@bytedance.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210831103634.33-2-xieyongji@bytedance.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Including:
- New DART IOMMU driver for Apple Silicon M1 chips.
- Optimizations for iommu_[map/unmap] performance
- Selective TLB flush support for the AMD IOMMU driver to make
it more efficient on emulated IOMMUs.
- Rework IOVA setup and default domain type setting to move more
code out of IOMMU drivers and to support runtime switching
between certain types of default domains.
- VT-d Updates from Lu Baolu:
- Update the virtual command related registers
- Enable Intel IOMMU scalable mode by default
- Preset A/D bits for user space DMA usage
- Allow devices to have more than 32 outstanding PRs
- Various cleanups
- ARM SMMU Updates from Will Deacon:
- SMMUv3: Minor optimisation to avoid zeroing struct members on CMD submission
- SMMUv3: Increased use of batched commands to reduce submission latency
- SMMUv3: Refactoring in preparation for ECMDQ support
- SMMUv2: Fix races when probing devices with identical StreamIDs
- SMMUv2: Optimise walk cache flushing for Qualcomm implementations
- SMMUv2: Allow deep sleep states for some Qualcomm SoCs with shared clocks
- Various smaller optimizations, cleanups, and fixes
-----BEGIN PGP SIGNATURE-----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=zVaQ
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- New DART IOMMU driver for Apple Silicon M1 chips
- Optimizations for iommu_[map/unmap] performance
- Selective TLB flush support for the AMD IOMMU driver to make it more
efficient on emulated IOMMUs
- Rework IOVA setup and default domain type setting to move more code
out of IOMMU drivers and to support runtime switching between certain
types of default domains
- VT-d Updates from Lu Baolu:
- Update the virtual command related registers
- Enable Intel IOMMU scalable mode by default
- Preset A/D bits for user space DMA usage
- Allow devices to have more than 32 outstanding PRs
- Various cleanups
- ARM SMMU Updates from Will Deacon:
SMMUv3:
- Minor optimisation to avoid zeroing struct members on CMD submission
- Increased use of batched commands to reduce submission latency
- Refactoring in preparation for ECMDQ support
SMMUv2:
- Fix races when probing devices with identical StreamIDs
- Optimise walk cache flushing for Qualcomm implementations
- Allow deep sleep states for some Qualcomm SoCs with shared clocks
- Various smaller optimizations, cleanups, and fixes
* tag 'iommu-updates-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (85 commits)
iommu/io-pgtable: Abstract iommu_iotlb_gather access
iommu/arm-smmu: Fix missing unlock on error in arm_smmu_device_group()
iommu/vt-d: Add present bit check in pasid entry setup helpers
iommu/vt-d: Use pasid_pte_is_present() helper function
iommu/vt-d: Drop the kernel doc annotation
iommu/vt-d: Allow devices to have more than 32 outstanding PRs
iommu/vt-d: Preset A/D bits for user space DMA usage
iommu/vt-d: Enable Intel IOMMU scalable mode by default
iommu/vt-d: Refactor Kconfig a bit
iommu/vt-d: Remove unnecessary oom message
iommu/vt-d: Update the virtual command related registers
iommu: Allow enabling non-strict mode dynamically
iommu: Merge strictness and domain type configs
iommu: Only log strictness for DMA domains
iommu: Expose DMA domain strictness via sysfs
iommu: Express DMA strictness via the domain type
iommu/vt-d: Prepare for multiple DMA domain types
iommu/arm-smmu: Prepare for multiple DMA domain types
iommu/amd: Prepare for multiple DMA domain types
iommu: Introduce explicit type for non-strict DMA domains
...
Pull swiotlb updates from Konrad Rzeszutek Wilk:
"A new feature called restricted DMA pools. It allows SWIOTLB to
utilize per-device (or per-platform) allocated memory pools instead of
using the global one.
The first big user of this is ARM Confidential Computing where the
memory for DMA operations can be set per platform"
* 'stable/for-linus-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb: (23 commits)
swiotlb: use depends on for DMA_RESTRICTED_POOL
of: restricted dma: Don't fail device probe on rmem init failure
of: Move of_dma_set_restricted_buffer() into device.c
powerpc/svm: Don't issue ultracalls if !mem_encrypt_active()
s390/pv: fix the forcing of the swiotlb
swiotlb: Free tbl memory in swiotlb_exit()
swiotlb: Emit diagnostic in swiotlb_exit()
swiotlb: Convert io_default_tlb_mem to static allocation
of: Return success from of_dma_set_restricted_buffer() when !OF_ADDRESS
swiotlb: add overflow checks to swiotlb_bounce
swiotlb: fix implicit debugfs declarations
of: Add plumbing for restricted DMA pool
dt-bindings: of: Add restricted DMA pool
swiotlb: Add restricted DMA pool initialization
swiotlb: Add restricted DMA alloc/free support
swiotlb: Refactor swiotlb_tbl_unmap_single
swiotlb: Move alloc_size to swiotlb_find_slots
swiotlb: Use is_swiotlb_force_bounce for swiotlb data bouncing
swiotlb: Update is_swiotlb_active to add a struct device argument
swiotlb: Update is_swiotlb_buffer to add a struct device argument
...
- fix debugfs initialization order (Anthony Iliopoulos)
- use memory_intersects() directly (Kefeng Wang)
- allow to return specific errors from ->map_sg
(Logan Gunthorpe, Martin Oliveira)
- turn the dma_map_sg return value into an unsigned int (me)
- provide a common global coherent pool іmplementation (me)
-----BEGIN PGP SIGNATURE-----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=spje
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.15' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- fix debugfs initialization order (Anthony Iliopoulos)
- use memory_intersects() directly (Kefeng Wang)
- allow to return specific errors from ->map_sg (Logan Gunthorpe,
Martin Oliveira)
- turn the dma_map_sg return value into an unsigned int (me)
- provide a common global coherent pool іmplementation (me)
* tag 'dma-mapping-5.15' of git://git.infradead.org/users/hch/dma-mapping: (31 commits)
hexagon: use the generic global coherent pool
dma-mapping: make the global coherent pool conditional
dma-mapping: add a dma_init_global_coherent helper
dma-mapping: simplify dma_init_coherent_memory
dma-mapping: allow using the global coherent pool for !ARM
ARM/nommu: use the generic dma-direct code for non-coherent devices
dma-direct: add support for dma_coherent_default_memory
dma-mapping: return an unsigned int from dma_map_sg{,_attrs}
dma-mapping: disallow .map_sg operations from returning zero on error
dma-mapping: return error code from dma_dummy_map_sg()
x86/amd_gart: don't set failed sg dma_address to DMA_MAPPING_ERROR
x86/amd_gart: return error code from gart_map_sg()
xen: swiotlb: return error code from xen_swiotlb_map_sg()
parisc: return error code from .map_sg() ops
sparc/iommu: don't set failed sg dma_address to DMA_MAPPING_ERROR
sparc/iommu: return error codes from .map_sg() ops
s390/pci: don't set failed sg dma_address to DMA_MAPPING_ERROR
s390/pci: return error code from s390_dma_map_sg()
powerpc/iommu: don't set failed sg dma_address to DMA_MAPPING_ERROR
powerpc/iommu: return error code from .map_sg() ops
...
These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform
support and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iD8DBQBhLz215t5GS2LDRf4RAjlHAJ473D0PymaTzv68EuPHThG+DEPifQCdGjLq
QGBB6JidIP8rtEdC+LWBB8I=
=M5+N
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform support
and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas"
* tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (96 commits)
reset: simple: remove ZTE details in Kconfig help
soc: rockchip: io-domain: Remove unneeded semicolon
soc: rockchip: io-domain: add rk3568 support
dt-bindings: power: add rk3568-pmu-io-domain support
bus: ixp4xx: return on error in ixp4xx_exp_probe()
soc: renesas: Prefer memcpy() over strcpy()
firmware: tegra: Stop using seq_get_buf()
soc/tegra: fuse: Enable fuse clock on suspend for Tegra124
soc/tegra: fuse: Add runtime PM support
soc/tegra: fuse: Clear fuse->clk on driver probe failure
soc/tegra: pmc: Prevent racing with cpuilde driver
soc/tegra: bpmp: Remove unused including <linux/version.h>
dt-bindings: soc: ti: pruss: Add dma-coherent property
soc: ti: Remove pm_runtime_irq_safe() usage for smartreflex
soc: ti: pruss: Enable support for ICSSG subsystems on K3 AM64x SoCs
dt-bindings: soc: ti: pruss: Update bindings for K3 AM64x SoCs
firmware: arm_scmi: Use WARN_ON() to check configured transports
firmware: arm_scmi: Fix boolconv.cocci warnings
soc: mediatek: mmsys: Fix missing UFOE component in mt8173 table routing
soc: mediatek: mmsys: add MT8365 support
...
- Improve ftrace code patching so that stop_machine is not required anymore.
This requires a small common code patch acked by Steven Rostedt:
https://lore.kernel.org/linux-s390/20210730220741.4da6fdf6@oasis.local.home/
- Enable KCSAN for s390. This comes with a small common code change to fix a
compile warning. Acked by Marco Elver:
https://lore.kernel.org/r/20210729142811.1309391-1-hca@linux.ibm.com
- Add KFENCE support for s390. This also comes with a minimal x86 patch from
Marco Elver who said also this can be carried via the s390 tree:
https://lore.kernel.org/linux-s390/YQJdarx6XSUQ1tFZ@elver.google.com/
- More changes to prepare the decompressor for relocation.
- Enable DAT also for CPU restart path.
- Final set of register asm removal patches; leaving only three locations where
needed and sane.
- Add NNPA, Vector-Packed-Decimal-Enhancement Facility 2, PCI MIO support to
hwcaps flags.
- Cleanup hwcaps implementation.
- Add new instructions to in-kernel disassembler.
- Various QDIO cleanups.
- Add SCLP debug feature.
- Various other cleanups and improvements all over the place.
-----BEGIN PGP SIGNATURE-----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=WDRh
-----END PGP SIGNATURE-----
Merge tag 's390-5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Heiko Carstens:
- Improve ftrace code patching so that stop_machine is not required
anymore. This requires a small common code patch acked by Steven
Rostedt:
https://lore.kernel.org/linux-s390/20210730220741.4da6fdf6@oasis.local.home/
- Enable KCSAN for s390. This comes with a small common code change to
fix a compile warning. Acked by Marco Elver:
https://lore.kernel.org/r/20210729142811.1309391-1-hca@linux.ibm.com
- Add KFENCE support for s390. This also comes with a minimal x86 patch
from Marco Elver who said also this can be carried via the s390 tree:
https://lore.kernel.org/linux-s390/YQJdarx6XSUQ1tFZ@elver.google.com/
- More changes to prepare the decompressor for relocation.
- Enable DAT also for CPU restart path.
- Final set of register asm removal patches; leaving only three
locations where needed and sane.
- Add NNPA, Vector-Packed-Decimal-Enhancement Facility 2, PCI MIO
support to hwcaps flags.
- Cleanup hwcaps implementation.
- Add new instructions to in-kernel disassembler.
- Various QDIO cleanups.
- Add SCLP debug feature.
- Various other cleanups and improvements all over the place.
* tag 's390-5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (105 commits)
s390: remove SCHED_CORE from defconfigs
s390/smp: do not use nodat_stack for secondary CPU start
s390/smp: enable DAT before CPU restart callback is called
s390: update defconfigs
s390/ap: fix state machine hang after failure to enable irq
KVM: s390: generate kvm hypercall functions
s390/sclp: add tracing of SCLP interactions
s390/debug: add early tracing support
s390/debug: fix debug area life cycle
s390/debug: keep debug data on resize
s390/diag: make restart_part2 a local label
s390/mm,pageattr: fix walk_pte_level() early exit
s390: fix typo in linker script
s390: remove do_signal() prototype and do_notify_resume() function
s390/crypto: fix all kernel-doc warnings in vfio_ap_ops.c
s390/pci: improve DMA translation init and exit
s390/pci: simplify CLP List PCI handling
s390/pci: handle FH state mismatch only on disable
s390/pci: fix misleading rc in clp_set_pci_fn()
s390/boot: factor out offset_vmlinux_info() function
...
Currently zpci_dma_init_device()/zpci_dma_exit_device() is called as
part of zpci_enable_device()/zpci_disable_device() and errors for
zpci_dma_exit_device() are always ignored even if we could abort.
Improve upon this by moving zpci_dma_exit_device() out of
zpci_disable_device() and check for errors whenever we have a way to
abort the current operation. Note that for example in
zpci_event_hard_deconfigured() the device is expected to be gone so we
really can't abort and proceed even in case of error.
Similarly move the cc == 3 special case out of zpci_unregister_ioat()
and into the callers allowing to abort when finding an already disabled
devices precludes proceeding with the operation.
While we are at it log IOAT register/unregister errors in the s390
debugfs log,
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Previously io-pgtable merely passed the iommu_iotlb_gather pointer
through to helpers, but now it has grown its own direct dereference.
This turns out to break the build for !IOMMU_API configs where the
structure only has a dummy definition. It will probably also crash
drivers who don't use the gather mechanism and simply pass in NULL.
Wrap this dereference in a suitable helper which can both be stubbed
out for !IOMMU_API and encapsulate a NULL check otherwise.
Fixes: 7a7c5badf8 ("iommu: Indicate queued flushes via gather data")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/83672ee76f6405c82845a55c148fa836f56fbbc1.1629465282.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add the missing unlock before return from function arm_smmu_device_group()
in the error handling case.
Fixes: b1a1347912 ("iommu/arm-smmu: Fix race condition during iommu_group creation")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210820074949.1946576-1-yangyingliang@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Kernel doc validator is unhappy with the following
.../perf.c:16: warning: Function parameter or member 'latency_lock' not described in 'DEFINE_SPINLOCK'
.../perf.c:16: warning: expecting prototype for perf.c(). Prototype was for DEFINE_SPINLOCK() instead
Drop kernel doc annotation since the top comment is not in the required format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210729163538.40101-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210818134852.1847070-8-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The minimum per-IOMMU PRQ queue size is one 4K page, this is more entries
than the hardcoded limit of 32 in the current VT-d code. Some devices can
support up to 512 outstanding PRQs but underutilized by this limit of 32.
Although, 32 gives some rough fairness when multiple devices share the same
IOMMU PRQ queue, but far from optimal for customized use case. This extends
the per-IOMMU PRQ queue size to four 4K pages and let the devices have as
many outstanding page requests as they can.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210720013856.4143880-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20210818134852.1847070-7-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
We preset the access and dirty bits for IOVA over first level usage only
for the kernel DMA (i.e., when domain type is IOMMU_DOMAIN_DMA). We should
also preset the FL A/D for user space DMA usage. The idea is that even the
user space A/D bit memory write is unnecessary. We should avoid it to
minimize the overhead.
Suggested-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210720013856.4143880-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20210818134852.1847070-6-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The commit 8950dcd83a ("iommu/vt-d: Leave scalable mode default off")
leaves the scalable mode default off and end users could turn it on with
"intel_iommu=sm_on". Using the Intel IOMMU scalable mode for kernel DMA,
user-level device access and Shared Virtual Address have been enabled.
This enables the scalable mode by default if the hardware advertises the
support and adds kernel options of "intel_iommu=sm_on/sm_off" for end
users to configure it through the kernel parameters.
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Suggested-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20210720013856.4143880-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20210818134852.1847070-5-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This fixes the "shared memory state machine" (SMSM) interrupt logic to
avoid missing transitions happening while the interrupts are masked.
SM6115 support is added to smd-rpm and rpmpd.
The Qualcomm SCM firmware driver is once again made possible to compile
and load as a kernel module.
An out-of-bounds error related to the cooling devices of the AOSS driver
is corrected. The binding is converted to YAML and a generic compatible
is introduced to reduce the driver churn.
The GENI wrapper gains a helper function used in I2C and SPI for
switching the serial engine hardware to use the wrapper's DMA-engine.
Lastly it contains a number of cleanups and smaller fixes for rpmhpd,
socinfo, CPR, mdt_loader and the GENI DT binding.
-----BEGIN PGP SIGNATURE-----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=88qN
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=dS58
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm driver updates for v5.15
This fixes the "shared memory state machine" (SMSM) interrupt logic to
avoid missing transitions happening while the interrupts are masked.
SM6115 support is added to smd-rpm and rpmpd.
The Qualcomm SCM firmware driver is once again made possible to compile
and load as a kernel module.
An out-of-bounds error related to the cooling devices of the AOSS driver
is corrected. The binding is converted to YAML and a generic compatible
is introduced to reduce the driver churn.
The GENI wrapper gains a helper function used in I2C and SPI for
switching the serial engine hardware to use the wrapper's DMA-engine.
Lastly it contains a number of cleanups and smaller fixes for rpmhpd,
socinfo, CPR, mdt_loader and the GENI DT binding.
* tag 'qcom-drivers-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: smsm: Fix missed interrupts if state changes while masked
soc: qcom: smsm: Implement support for get_irqchip_state
soc: qcom: mdt_loader: be more informative on errors
dt-bindings: qcom: geni-se: document iommus
soc: qcom: smd-rpm: Add SM6115 compatible
soc: qcom: geni: Add support for gpi dma
soc: qcom: geni: move GENI_IF_DISABLE_RO to common header
PM: AVS: qcom-cpr: Use nvmem_cell_read_variable_le_u32()
drivers: soc: qcom: rpmpd: Add SM6115 RPM Power Domains
dt-bindings: power: rpmpd: Add SM6115 to rpmpd binding
dt-bindings: soc: qcom: smd-rpm: Add SM6115 compatible
soc: qcom: aoss: Fix the out of bound usage of cooling_devs
firmware: qcom_scm: Allow qcom_scm driver to be loadable as a permenent module
soc: qcom: socinfo: Don't print anything if nothing found
soc: qcom: rpmhpd: Use corner in power_off
soc: qcom: aoss: Add generic compatible
dt-bindings: soc: qcom: aoss: Convert to YAML
dt-bindings: soc: qcom: aoss: Add SC8180X and generic compatible
firmware: qcom_scm: remove a duplicative condition
firmware: qcom_scm: Mark string array const
Link: https://lore.kernel.org/r/20210816214840.581244-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Allocating and enabling a flush queue is in fact something we can
reasonably do while a DMA domain is active, without having to rebuild it
from scratch. Thus we can allow a strict -> non-strict transition from
sysfs without requiring to unbind the device's driver, which is of
particular interest to users who want to make selective relaxations to
critical devices like the one serving their root filesystem.
Disabling and draining a queue also seems technically possible to
achieve without rebuilding the whole domain, but would certainly be more
involved. Furthermore there's not such a clear use-case for tightening
up security *after* the device may already have done whatever it is that
you don't trust it not to do, so we only consider the relaxation case.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/d652966348c78457c38bf18daf369272a4ebc2c9.1628682049.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
To parallel the sysfs behaviour, merge the new build-time option
for DMA domain strictness into the default domain type choice.
Suggested-by: Joerg Roedel <joro@8bytes.org>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/d04af35b9c0f2a1d39605d7a9b451f5e1f0c7736.1628682049.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When passthrough is enabled, the default strictness policy becomes
irrelevant, since any subsequent runtime override to a DMA domain type
now embodies an explicit choice of strictness as well. Save on noise by
only logging the default policy when it is meaningfully in effect.
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/9d2bcba880c6d517d0751ed8bd4960853030b4d7.1628682049.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The sysfs interface for default domain types exists primarily so users
can choose the performance/security tradeoff relevant to their own
workload. As such, the choice between the policies for DMA domains fits
perfectly as an additional point on that scale - downgrading a
particular device from a strict default to non-strict may be enough to
let it reach the desired level of performance, while still retaining
more peace of mind than with a wide-open identity domain. Now that we've
abstracted non-strict mode as a distinct type of DMA domain, allow it to
be chosen through the user interface as well.
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/0e08da5ed4069fd3473cfbadda758ca983becdbf.1628682049.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Eliminate the iommu_get_dma_strict() indirection and pipe the
information through the domain type from the beginning. Besides
the flow simplification this also has several nice side-effects:
- Automatically implies strict mode for untrusted devices by
virtue of their IOMMU_DOMAIN_DMA override.
- Ensures that we only end up using flush queues for drivers
which are aware of them and can actually benefit.
- Allows us to handle flush queue init failure by falling back
to strict mode instead of leaving it to possibly blow up later.
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/47083d69155577f1367877b1594921948c366eb3.1628682049.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In preparation for the strict vs. non-strict decision for DMA domains
to be expressed in the domain type, make sure we expose our flush queue
awareness by accepting the new domain type, and test the specific
feature flag where we want to identify DMA domains in general. The DMA
ops reset/setup can simply be made unconditional, since iommu-dma
already knows only to touch DMA domains.
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/31a8ef868d593a2f3826a6a120edee81815375a7.1628682049.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Promote the difference between strict and non-strict DMA domains from an
internal detail to a distinct domain feature and type, to pave the road
for exposing it through the sysfs default domain interface.
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/08cd2afaf6b63c58ad49acec3517c9b32c2bb946.1628682049.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
IO_PGTABLE_QUIRK_NON_STRICT was never a very comfortable fit, since it's
not a quirk of the pagetable format itself. Now that we have a more
appropriate way to convey non-strict unmaps, though, this last of the
non-quirk quirks can also go, and with the flush queue code also now
enforcing its own ordering we can have a lovely cleanup all round.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/155b5c621cd8936472e273a8b07a182f62c6c20d.1628682049.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Since iommu_iotlb_gather exists to help drivers optimise flushing for a
given unmap request, it is also the logical place to indicate whether
the unmap is strict or not, and thus help them further optimise for
whether to expect a sync or a flush_all subsequently. As part of that,
it also seems fair to make the flush queue code take responsibility for
enforcing the really subtle ordering requirement it brings, so that we
don't need to worry about forgetting that if new drivers want to add
flush queue support, and can consolidate the existing versions.
While we're adding to the kerneldoc, also fill in some info for
@freelist which was overlooked previously.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/bf5f8e2ad84e48c712ccbf80fa8c610594c7595f.1628682049.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
iommu_dma_init_domain() is now only called from iommu_setup_dma_ops(),
which has already assumed dev to be non-NULL.
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/06024523c080364390016550065e3cfe8031367e.1628682049.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Now that everyone has converged on iommu-dma for IOMMU_DOMAIN_DMA
support, we can abandon the notion of drivers being responsible for the
cookie type, and consolidate all the management into the core code.
CC: Yong Wu <yong.wu@mediatek.com>
CC: Chunyan Zhang <chunyan.zhang@unisoc.com>
CC: Maxime Ripard <mripard@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/46a2c0e7419c7d1d931762dc7b6a69fa082d199a.1628682048.git.robin.murphy@arm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This fixes improper iotlb invalidation in intel_pasid_tear_down_entry().
When a PASID was used as nested mode, released and reused, the following
error message will appear:
[ 180.187556] Unexpected page request in Privilege Mode
[ 180.187565] Unexpected page request in Privilege Mode
[ 180.279933] Unexpected page request in Privilege Mode
[ 180.279937] Unexpected page request in Privilege Mode
Per chapter 6.5.3.3 of VT-d spec 3.3, when tear down a pasid entry, the
software should use Domain selective IOTLB flush if the PGTT of the pasid
entry is SL only or Nested, while for the pasid entries whose PGTT is FL
only or PT using PASID-based IOTLB flush is enough.
Fixes: 2cd1311a26 ("iommu/vt-d: Add set domain DOMAIN_ATTR_NESTING attr")
Signed-off-by: Kumar Sanjay K <sanjay.k.kumar@intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Tested-by: Yi Sun <yi.y.sun@intel.com>
Link: https://lore.kernel.org/r/20210817042425.1784279-1-yi.l.liu@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210817124321.1517985-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
A PASID reference is increased whenever a device is bound to an mm (and
its PASID) successfully (i.e. the device's sdev user count is increased).
But the reference is not dropped every time the device is unbound
successfully from the mm (i.e. the device's sdev user count is decreased).
The reference is dropped only once by calling intel_svm_free_pasid() when
there isn't any device bound to the mm. intel_svm_free_pasid() drops the
reference and only frees the PASID on zero reference.
Fix the issue by dropping the PASID reference and freeing the PASID when
no reference on successful unbinding the device by calling
intel_svm_free_pasid() .
Fixes: 4048377414 ("iommu/vt-d: Use iommu_sva_alloc(free)_pasid() helpers")
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: https://lore.kernel.org/r/20210813181345.1870742-1-fenghua.yu@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210817124321.1517985-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Pre-zeroing the batched commands structure is inefficient, as individual
commands are zeroed later in arm_smmu_cmdq_build_cmd(). The size is quite
large and commonly most commands won't even be used:
struct arm_smmu_cmdq_batch cmds = {};
345c: 52800001 mov w1, #0x0 // #0
3460: d2808102 mov x2, #0x408 // #1032
3464: 910143a0 add x0, x29, #0x50
3468: 94000000 bl 0 <memset>
Stop pre-zeroing the complete structure and only zero the num member.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1628696966-88386-1-git-send-email-john.garry@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
When SMMU_GERROR.CMDQP_ERR is different to SMMU_GERRORN.CMDQP_ERR, it
indicates that one or more errors have been encountered on a command queue
control page interface. We need to traverse all ECMDQs in that control
page to find all errors. For each ECMDQ error handling, it is much the
same as the CMDQ error handling. This common processing part is extracted
as a new function __arm_smmu_cmdq_skip_err().
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210811114852.2429-5-thunder.leizhen@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
One SMMU has only one normal CMDQ. Therefore, this CMDQ is used regardless
of the core on which the command is inserted. It can be referenced
directly through "smmu->cmdq". However, one SMMU has multiple ECMDQs, and
the ECMDQ used by the core on which the command insertion is executed may
be different. So the helper function arm_smmu_get_cmdq() is added, which
returns the CMDQ/ECMDQ that the current core should use. Currently, the
code that supports ECMDQ is not added. just simply returns "&smmu->cmdq".
Many subfunctions of arm_smmu_cmdq_issue_cmdlist() use "&smmu->cmdq" or
"&smmu->cmdq.q" directly. To support ECMDQ, they need to call the newly
added function arm_smmu_get_cmdq() instead.
Note that normal CMDQ is still required until ECMDQ is available.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210811114852.2429-4-thunder.leizhen@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Marc Zyngier
Linus Torvalds
Joerg Roedel
Logan Gunthorpe
Sven Peter
Gustavo A. R. Silva
Christophe JAILLET
Wan Jiabing
Longpeng(Mike)
Fenghua Yu
Lu Baolu
Kyung Min Park
Tvrtko Ursulin
Arnd Bergmann
Sibi Sankar
Loic Poulain
Konrad Dybcio
Zhen Lei
Tom Lendacky
Lennert Buytenhek
David Stevens
Nikita Yushchenko
Bjorn Helgaas
Robin Murphy
Yoshihiro Shimoda
Kees Cook
Suravee Suthikulpanit
Wei Huang
Xie Yongji
Niklas Schnelle
Yang Yingliang
Liu Yi L
Andy Shevchenko
John Garry