The VMADDR_CID_RESERVED (1) was used by VMCI, but now it is not
used anymore, so we can reuse it for local communication
(loopback) adding the new well-know CID: VMADDR_CID_LOCAL.
Cc: Jorgen Hansen <jhansen@vmware.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can remove virtio header includes, because virtio_transport_common
doesn't use virtio API, but provides common functions to interface
virtio/vhost transports with the af_vsock core, and to handle
the protocol.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
Add support for slow-to-probe-PHY copper SFP modules
This series, following on from the previous adding SFP+ copper support,
adds support for a range of Copper SFP modules, made by a variety of
companies, all of which have a Marvell 88E1111 PHY on them, but take
far longer than the Marvell spec'd 15ms to start communicating on the
I2C bus.
Researching the Champion One 1000SFPT module reveals that TX_DISABLE is
routed through a MAX1971 switching regulator and reset IC which adds a
175ms delay to releasing the 88E1111 reset.
It is not known whether other modules use a similar setup, but there
are a range of modules that are slow for the Marvell PHY to appear.
This patch series adds support for these modules by repeatedly trying
to probe the PHY for up to 600ms.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some 1000BASE-T PHY modules take a while for the PHY to wake up.
Retry the probe a number of times before deciding that the module has
no PHY.
Tested with:
Sourcephotonics SPGBTXCNFC - PHY takes less than 50ms to respond.
Champion One 1000SFPT - PHY takes about 200ms to respond.
Mikrotik S-RJ01 - no PHY
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename sm_retries as sm_fault_retries, as this is what this member is
tracking.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
Add support for SFP+ copper modules
This series adds support for Copper SFP+ modules with Clause 45 PHYs.
Specifically the patches:
1. drop support for the probably never tested 100BASE-*X modules.
2. drop EEPROM ID from sfp_select_interface()
3. add more compliance code definitions from SFF-8024, renaming the
existing definitions.
4. add module start/stop methods so phylink knows when a module is
about to become active. The module start method is called after
we have probed for a PHY on the module.
5. move start/stop of module PHY down into phylink using the new
module start/stop methods.
6. add support for Clause 45 I2C accesses, tested with Methode DM7052.
Other modules appear to use the same protocol, but slight
differences, but I do not have those modules to test with.
(if someone does, please holler!)
7. rearrange how we attach to PHYs so that we can support Clause 45
PHYs with indeterminant interface modes. (Clause 45 PHYs appear
to like to change their PHY interface mode depending on the
negotiated speed.)
8. add support for phylink to connect to a clause 45 PHY on a SFP
module.
9. split the link_an_mode between the configured value and the
currently selected mode value; some clause 45 PHYs have no
capability to provide in-band negotiation.
10. split the link configuration on SFP module insertion in phylink
so we can use it in other code paths.
11. delay MAC configuration for copper modules without a PHY to the
module start method - after any module PHY has been probed. If
the module has a PHY, then we setup the MAC when the PHY is
detected.
12. the Broadcom 84881 PHY does not support in-band negotiation even
though it uses SGMII and 2500BASE-X. Having the MAC operating
with in-band negotiation enabled, even with AN bypass enabled,
results in no link - Broadcom say that the host MAC must always
be forced.
13. add support for the Broadcom 84881 PHY found on the Methode
DM7052 module.
14. add support to SFP to probe for a Clause 45 PHY on copper SFP+
modules.
v3: now bisectable!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some SFP+ modules have a Clause 45 PHY onboard, which is accessible via
the normal I2C address. Detect 10G BASE-T PHYs which may have an
accessible PHY and probe for it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a rudimentary Clause 45 driver for the BCM84881 PHY, found on
Methode DM7052 SFPs.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom BCM84881 does not appear to send the SGMII control word
when operating in SGMII mode, which causes network adapters to fail
to link with the PHY, or decide to operate at fixed 1G speed, even if
the PHY negotiated 100M.
Work around this by detecting the Broadcom BCM84881 and switch to phy
mode rather than inband mode.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Knowing whether we need to delay the MAC configuration because a module
may have a PHY is useful to phylink to allow NBASE-T modules to work on
systems supporting no more than 2.5G speeds.
This commit allows us to delay such configuration until after the PHY
has been probed by recording the parsed capabilities, and if the module
may have a PHY, doing no more until the module_start() notification is
called. At that point, we either have a PHY, or we don't.
We move the PHY-based setup a little later, and use the PHYs support
capabilities rather than the EEPROM parsed capabilities to determine
whether we can support the PHY.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split out the configuration step from phylink_sfp_module_insert() so
we can re-use this later.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split link_an_mode between the configured setting and the current
operating setting. This is an important distinction to make when we
need to configure PHY mode for a plugged SFP+ module that does not
use in-band signalling.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some SFP+ modules have Clause 45 PHYs embedded on them, which need a
little more handling in order to ensure that they are correctly setup,
as they switch the PHY link mode according to the negotiated speed.
With Clause 22 PHYs, we assumed that they would operate in SGMII mode,
but this assumption is now false. Adapt phylink to support Clause 45
PHYs on SFP+ modules.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support Clause 45 PHYs on SFP+ modules, which have an
indeterminant phy interface mode, we need to be able to call
phylink_bringup_phy() with a different interface mode to that used when
binding the PHY. Reduce __phylink_connect_phy() to an attach operation,
and move the call to phylink_bringup_phy() to its call sites.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some SFP+ modules have PHYs on them just like SFP modules do, except
they are Clause 45 PHYs. The I2C protocol used to access them is
modified slightly in order to send the device address and 16-bit
register index.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move phy_start() and phy_stop() into the module_start and module_stop
notifications in phylink, rather than having them in the SFP code.
This gives phylink responsibility for controlling the PHY, rather
than having SFP start and stop the PHY state machine.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dealing with some copper modules, we can't positively know the
module capabilities are until we have probed the PHY. Without the full
capabilities, we may end up failing a module that we could otherwise
drive with a restricted set of capabilities.
An example of this would be a module with a NBASE-T PHY plugged into
a host that supports phy interface modes 2500BASE-X and SGMII. The
PHY supports 10GBASE-R, 5000BASE-X, 2500BASE-X, SGMII interface modes,
which means a subset of the capabilities are compatible with the host.
However, reading the module EEPROM leads us to believe that the module
only supports ethtool link mode 10GBASE-T, which is incompatible with
the host - and thus results in the module being rejected.
This patch adds an extra notification which are triggered after the
SFP module's PHY probe, and a corresponding notification just before
the PHY is removed.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFF-8024 is used to define various constants re-used in several SFF
SFP-related specifications. Split these constants from the enum, and
rename them to indicate that they're defined by SFF-8024.
Add and use updated SFF-8024 extended compliance code definitions for
10GBASE-T, 5GBASE-T and 2.5GBASE-T modules.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need the EEPROM ID to derive the phy interface mode as we can
derive it merely from the ethtool link modes. Remove the EEPROM ID
argument to sfp_select_interface().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 100BASE-FX and 100BASE-LX support assumes a PHY is present; this
is probably an incorrect assumption. In any case, sfp_parse_support()
will fail such a module. Let's stop pretending we support these
modules.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
T6 has a separate region known as high priority filter region
that allows classifying packets going through ULD path. So,
query firmware for HPFILTER resources and enable the high
priority offload filter support when it is available.
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/freescale/enetc/enetc_qos.c: In function enetc_setup_tc_cbs:
drivers/net/ethernet/freescale/enetc/enetc_qos.c:195:6: warning: variable tc_max_sized_frame set but not used [-Wunused-but-set-variable]
Fixes: c431047c4e ("enetc: add support Credit Based Shaper(CBS) for hardware offload")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device stats are currently hard coded in the PCI BAR0 layout.
Add a ability to read them from the TLV area instead.
Names for the stats are maintained by the driver, and their
meaning documented. This allows us to more easily add and
remove device stats.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a TCP socket is created, sk->sk_state is initialized twice as
TCP_CLOSE in sock_init_data() and tcp_init_sock(). The tcp_init_sock() is
always called after the sock_init_data(), so it is not necessary to update
sk->sk_state in the tcp_init_sock().
Before v2.1.8, the code of the two functions was in the inet_create(). In
the patch of v2.1.8, the tcp_v4/v6_init_sock() were added and the code of
initialization of sk->state was duplicated.
Signed-off-by: Kuniyuki Iwashima <kuni1840@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a software TX timestamp and add it to the ethtool query
interface.
skb_tx_timestamp() is also needed if one would like to use PHY
timestamping.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy says:
====================
tipc: introduce variable window congestion control
We improve thoughput greatly by introducing a variety of the Reno
congestion control algorithm at the link level.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We introduce a simple variable window congestion control for links.
The algorithm is inspired by the Reno algorithm, covering both 'slow
start', 'congestion avoidance', and 'fast recovery' modes.
- We introduce hard lower and upper window limits per link, still
different and configurable per bearer type.
- We introduce a 'slow start theshold' variable, initially set to
the maximum window size.
- We let a link start at the minimum congestion window, i.e. in slow
start mode, and then let is grow rapidly (+1 per rceived ACK) until
it reaches the slow start threshold and enters congestion avoidance
mode.
- In congestion avoidance mode we increment the congestion window for
each window-size number of acked packets, up to a possible maximum
equal to the configured maximum window.
- For each non-duplicate NACK received, we drop back to fast recovery
mode, by setting the both the slow start threshold to and the
congestion window to (current_congestion_window / 2).
- If the timeout handler finds that the transmit queue has not moved
since the previous timeout, it drops the link back to slow start
and forces a probe containing the last sent sequence number to the
sent to the peer, so that this can discover the stale situation.
This change does in reality have effect only on unicast ethernet
transport, as we have seen that there is no room whatsoever for
increasing the window max size for the UDP bearer.
For now, we also choose to keep the limits for the broadcast link
unchanged and equal.
This algorithm seems to give a 50-100% throughput improvement for
messages larger than MTU.
Suggested-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we increase the link tranmsit window we often observe the following
scenario:
1) A STATE message bypasses a sequence of traffic packets and arrives
far ahead of those to the receiver. STATE messages contain a
'peers_nxt_snt' field to indicate which was the last packet sent
from the peer. This mechanism is intended as a last resort for the
receiver to detect missing packets, e.g., during very low traffic
when there is no packet flow to help early loss detection.
3) The receiving link compares the 'peer_nxt_snt' field to its own
'rcv_nxt', finds that there is a gap, and immediately sends a
NACK message back to the peer.
4) When this NACKs arrives at the sender, all the requested
retransmissions are performed, since it is a first-time request.
Just like in the scenario described in the previous commit this leads
to many redundant retransmissions, with decreased throughput as a
consequence.
We fix this by adding two more conditions before we send a NACK in
this sitution. First, the deferred queue must be empty, so we cannot
assume that the potential packet loss has already been detected by
other means. Second, we check the 'peers_snd_nxt' field only in probe/
probe_reply messages, thus turning this into a true mechanism of last
resort as it was really meant to be.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we increase the link send window we sometimes observe the
following scenario:
1) A packet #N arrives out of order far ahead of a sequence of older
packets which are still under way. The packet is added to the
deferred queue.
2) The missing packets arrive in sequence, and for each 16th of them
an ACK is sent back to the receiver, as it should be.
3) When building those ACK messages, it is checked if there is a gap
between the link's 'rcv_nxt' and the first packet in the deferred
queue. This is always the case until packet number #N-1 arrives, and
a 'gap' indicator is added, effectively turning them into NACK
messages.
4) When those NACKs arrive at the sender, all the requested
retransmissions are done, since it is a first-time request.
This sometimes leads to a huge amount of redundant retransmissions,
causing a drop in max throughput. This problem gets worse when we
in a later commit introduce variable window congestion control,
since it drops the link back to 'fast recovery' much more often
than necessary.
We now fix this by not sending any 'gap' indicator in regular ACK
messages. We already have a mechanism for sending explicit NACKs
in place, and this is sufficient to keep up the packet flow.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
../drivers/net/ppp/ppp_async.c:877:6: warning: misleading indentation;
statement is not part of the previous 'if' [-Wmisleading-indentation]
ap->rpkt = skb;
^
../drivers/net/ppp/ppp_async.c:875:5: note: previous statement is here
if (!skb)
^
1 warning generated.
This warning occurs because there is a space before the tab on this
line. Clean up this entire block's indentation so that it is consistent
with the Linux kernel coding style and clang no longer warns.
Fixes: 6722e78c90 ("[PPP]: handle misaligned accesses")
Link: https://github.com/ClangBuiltLinux/linux/issues/800
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
../drivers/net/ethernet/smsc/smc911x.c:939:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
if (!lp->ctl_rfduplx)
^
../drivers/net/ethernet/smsc/smc911x.c:936:2: note: previous statement
is here
if (lp->ctl_rspeed != 100)
^
1 warning generated.
This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
Fixes: 0a0c72c911 ("[PATCH] RE: [PATCH 1/1] net driver: Add support for SMSC LAN911x line of ethernet chips")
Link: https://github.com/ClangBuiltLinux/linux/issues/796
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
../drivers/net/ethernet/dec/tulip/uli526x.c:1812:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
switch (mode) {
^
../drivers/net/ethernet/dec/tulip/uli526x.c:1809:2: note: previous
statement is here
if (cr6set)
^
1 warning generated.
../drivers/net/ethernet/dec/tulip/dmfe.c:2217:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
switch(mode) {
^
../drivers/net/ethernet/dec/tulip/dmfe.c:2214:2: note: previous
statement is here
if (cr6set)
^
1 warning generated.
This warning occurs because there is a space before the tab on these
lines. Remove them so that the indentation is consistent with the Linux
kernel coding style and clang no longer warns.
While we are here, adjust the default block in dmfe_init_module to have
a proper break between the label and assignment and add a space between
the switch and opening parentheses to avoid a checkpatch warning.
Fixes: e1c3e50140 ("[PATCH] initialisation cleanup for ULI526x-net-driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/795
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Murphy says:
====================
Fix Tx/Rx FIFO depth for DP83867
The DP83867 supports both the RGMII and SGMII modes. The Tx and Rx FIFO depths
are configurable in these modes but may not applicable for both modes.
When the device is configured for RGMII mode the Tx FIFO depth is applicable
and for SGMII mode both Tx and Rx FIFO depth settings are applicable. When
the driver was originally written only the RGMII device was available and there
were no standard fifo-depth DT properties.
The patchset converts the special ti,fifo-depth property to the standard
tx-fifo-depth property while still allowing the ti,fifo-depth property to be
set as to maintain backward compatibility.
In addition to this change the rx-fifo-depth property support was added and only
written when the device is configured for SGMII mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This code changes the TI specific ti,fifo-depth to the common
tx-fifo-depth property. The tx depth is applicable for both RGMII and
SGMII modes of operation.
rx-fifo-depth was added as well but this is only applicable for SGMII
mode.
So in summary
if RGMII mode write tx fifo depth only
if SGMII mode write both rx and tx fifo depths
If the property is not populated in the device tree then set the value
to the default values.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the ti,fifo-depth from a TI specific property to the common
tx-fifo-depth property. Also add support for the rx-fifo-depth.
These are optional properties for this device and if these are not
available then the fifo depths are set to device default values.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reported-by: Adrian Bunk <bunk@kernel.org>
CC: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a sysctl knob "net.ipv4.tcp_no_ssthresh_metrics_save"
that disables TCP ssthresh metrics cache by default. Other parts of TCP
metrics cache, e.g. rtt, cwnd, remain unchanged.
As modern networks becoming more and more dynamic, TCP metrics cache
today often causes more harm than benefits. For example, the same IP
address is often shared by different subscribers behind NAT in residential
networks. Even if the IP address is not shared by different users,
caching the slow-start threshold of a previous short flow using loss-based
congestion control (e.g. cubic) often causes the future longer flows of
the same network path to exit slow-start prematurely with abysmal
throughput.
Caching ssthresh is very risky and can lead to terrible performance.
Therefore it makes sense to make disabling ssthresh caching by
default and opt-in for specific networks by the administrators.
This practice also has worked well for several years of deployment with
CUBIC congestion control at Google.
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Kevin(Yudong) Yang <yyd@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 312434617c ("sctp: cache netns in sctp_ep_common") set netns
in asoc and ep base since they're created, and it will never change.
It's a better way to get netns from asoc and ep base, comparing to
calling sock_net().
This patch is to replace them.
v1->v2:
- no change.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Nokia GPON module can hold tx-fault active while it is initialising
which can take up to 60s. Avoid this causing the module to be declared
faulty after the SFP MSA defined non-cooled module timeout.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable rc is assigned with a value that is never read and
it is re-assigned a new value later on. The assignment is redundant
and can be removed. Clean up multiple occurrances of this pattern.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert cpu_to_le16(le16_to_cpu(frame->datalen) + len) to
use le16_add_cpu(), which is more concise and does the same thing.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2019-12-09
Here's the first bluetooth-next pull request for 5.6:
- Devicetree bindings updates for Broadcom controllers
- Add support for PCM configuration for Broadcom controllers
- btusb: Fixes for Realtek devices
- butsb: A few other smaller fixes (mem leak & non-atomic allocation issue)
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
WireGuard is a layer 3 secure networking tunnel made specifically for
the kernel, that aims to be much simpler and easier to audit than IPsec.
Extensive documentation and description of the protocol and
considerations, along with formal proofs of the cryptography, are
available at:
* https://www.wireguard.com/
* https://www.wireguard.com/papers/wireguard.pdf
This commit implements WireGuard as a simple network device driver,
accessible in the usual RTNL way used by virtual network drivers. It
makes use of the udp_tunnel APIs, GRO, GSO, NAPI, and the usual set of
networking subsystem APIs. It has a somewhat novel multicore queueing
system designed for maximum throughput and minimal latency of encryption
operations, but it is implemented modestly using workqueues and NAPI.
Configuration is done via generic Netlink, and following a review from
the Netlink maintainer a year ago, several high profile userspace tools
have already implemented the API.
This commit also comes with several different tests, both in-kernel
tests and out-of-kernel tests based on network namespaces, taking profit
of the fact that sockets used by WireGuard intentionally stay in the
namespace the WireGuard interface was originally created, exactly like
the semantics of userspace tun devices. See wireguard.com/netns/ for
pictures and examples.
The source code is fairly short, but rather than combining everything
into a single file, WireGuard is developed as cleanly separable files,
making auditing and comprehension easier. Things are laid out as
follows:
* noise.[ch], cookie.[ch], messages.h: These implement the bulk of the
cryptographic aspects of the protocol, and are mostly data-only in
nature, taking in buffers of bytes and spitting out buffers of
bytes. They also handle reference counting for their various shared
pieces of data, like keys and key lists.
* ratelimiter.[ch]: Used as an integral part of cookie.[ch] for
ratelimiting certain types of cryptographic operations in accordance
with particular WireGuard semantics.
* allowedips.[ch], peerlookup.[ch]: The main lookup structures of
WireGuard, the former being trie-like with particular semantics, an
integral part of the design of the protocol, and the latter just
being nice helper functions around the various hashtables we use.
* device.[ch]: Implementation of functions for the netdevice and for
rtnl, responsible for maintaining the life of a given interface and
wiring it up to the rest of WireGuard.
* peer.[ch]: Each interface has a list of peers, with helper functions
available here for creation, destruction, and reference counting.
* socket.[ch]: Implementation of functions related to udp_socket and
the general set of kernel socket APIs, for sending and receiving
ciphertext UDP packets, and taking care of WireGuard-specific sticky
socket routing semantics for the automatic roaming.
* netlink.[ch]: Userspace API entry point for configuring WireGuard
peers and devices. The API has been implemented by several userspace
tools and network management utility, and the WireGuard project
distributes the basic wg(8) tool.
* queueing.[ch]: Shared function on the rx and tx path for handling
the various queues used in the multicore algorithms.
* send.c: Handles encrypting outgoing packets in parallel on
multiple cores, before sending them in order on a single core, via
workqueues and ring buffers. Also handles sending handshake and cookie
messages as part of the protocol, in parallel.
* receive.c: Handles decrypting incoming packets in parallel on
multiple cores, before passing them off in order to be ingested via
the rest of the networking subsystem with GRO via the typical NAPI
poll function. Also handles receiving handshake and cookie messages
as part of the protocol, in parallel.
* timers.[ch]: Uses the timer wheel to implement protocol particular
event timeouts, and gives a set of very simple event-driven entry
point functions for callers.
* main.c, version.h: Initialization and deinitialization of the module.
* selftest/*.h: Runtime unit tests for some of the most security
sensitive functions.
* tools/testing/selftests/wireguard/netns.sh: Aforementioned testing
script using network namespaces.
This commit aims to be as self-contained as possible, implementing
WireGuard as a standalone module not needing much special handling or
coordination from the network subsystem. I expect for future
optimizations to the network stack to positively improve WireGuard, and
vice-versa, but for the time being, this exists as intentionally
standalone.
We introduce a menu option for CONFIG_WIREGUARD, as well as providing a
verbose debug log and self-tests via CONFIG_WIREGUARD_DEBUG.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: David Miller <davem@davemloft.net>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) More jumbo frame fixes in r8169, from Heiner Kallweit.
2) Fix bpf build in minimal configuration, from Alexei Starovoitov.
3) Use after free in slcan driver, from Jouni Hogander.
4) Flower classifier port ranges don't work properly in the HW offload
case, from Yoshiki Komachi.
5) Use after free in hns3_nic_maybe_stop_tx(), from Yunsheng Lin.
6) Out of bounds access in mqprio_dump(), from Vladyslav Tarasiuk.
7) Fix flow dissection in dsa TX path, from Alexander Lobakin.
8) Stale syncookie timestampe fixes from Guillaume Nault.
[ Did an evil merge to silence a warning introduced by this pull - Linus ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
r8169: fix rtl_hw_jumbo_disable for RTL8168evl
net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add()
r8169: add missing RX enabling for WoL on RTL8125
vhost/vsock: accept only packets with the right dst_cid
net: phy: dp83867: fix hfs boot in rgmii mode
net: ethernet: ti: cpsw: fix extra rx interrupt
inet: protect against too small mtu values.
gre: refetch erspan header from skb->data after pskb_may_pull()
pppoe: remove redundant BUG_ON() check in pppoe_pernet
tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()
tcp: tighten acceptance of ACKs not matching a child socket
tcp: fix rejected syncookies due to stale timestamps
lpc_eth: kernel BUG on remove
tcp: md5: fix potential overestimation of TCP option space
net: sched: allow indirect blocks to bind to clsact in TC
net: core: rename indirect block ingress cb function
net-sysfs: Call dev_hold always in netdev_queue_add_kobject
net: dsa: fix flow dissection on Tx path
net/tls: Fix return values to avoid ENOTSUPP
net: avoid an indirect call in ____sys_recvmsg()
...
11 patches, all in drivers (no core changes) that are either minor
cleanups or small fixes. They were late arriving, but still safe for
-rc1.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXeyDEiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbijAQDIuM45
xeEXgWXF8c/tYuvildK1WjyVzwBO2k563lUmYQEA4rxSzkmhtcaMTDuk4hI4Y4TP
p87U1bXNSJ7tCpFU15w=
=W43H
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"Eleven patches, all in drivers (no core changes) that are either minor
cleanups or small fixes.
They were late arriving, but still safe for -rc1"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: MAINTAINERS: Add the linux-scsi mailing list to the ISCSI entry
scsi: megaraid_sas: Make poll_aen_lock static
scsi: sd_zbc: Improve report zones error printout
scsi: qla2xxx: Fix qla2x00_request_irqs() for MSI
scsi: qla2xxx: unregister ports after GPN_FT failure
scsi: qla2xxx: fix rports not being mark as lost in sync fabric scan
scsi: pm80xx: Remove unused include of linux/version.h
scsi: pm80xx: fix logic to break out of loop when register value is 2 or 3
scsi: scsi_transport_sas: Fix memory leak when removing devices
scsi: lpfc: size cpu map by last cpu id set
scsi: ibmvscsi_tgt: Remove unneeded variable rc
-----BEGIN PGP SIGNATURE-----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=gey9
-----END PGP SIGNATURE-----
Merge tag '5.5-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Nine cifs/smb3 fixes:
- one fix for stable (oops during oplock break)
- two timestamp fixes including important one for updating mtime at
close to avoid stale metadata caching issue on dirty files (also
improves perf by using SMB2_CLOSE_FLAG_POSTQUERY_ATTRIB over the
wire)
- two fixes for "modefromsid" mount option for file create (now
allows mode bits to be set more atomically and accurately on create
by adding "sd_context" on create when modefromsid specified on
mount)
- two fixes for multichannel found in testing this week against
different servers
- two small cleanup patches"
* tag '5.5-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
smb3: improve check for when we send the security descriptor context on create
smb3: fix mode passed in on create for modetosid mount option
cifs: fix possible uninitialized access and race on iface_list
cifs: Fix lookup of SMB connections on multichannel
smb3: query attributes on file close
smb3: remove unused flag passed into close functions
cifs: remove redundant assignment to pointer pneg_ctxt
fs: cifs: Fix atime update check vs mtime
CIFS: Fix NULL-pointer dereference in smb2_push_mandatory_locks
Pull misc vfs cleanups from Al Viro:
"No common topic, just three cleanups".
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
make __d_alloc() static
fs/namespace: add __user to open_tree and move_mount syscalls
fs/fnctl: fix missing __user in fcntl_rw_hint()
-----BEGIN PGP SIGNATURE-----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=rWRP
-----END PGP SIGNATURE-----
Merge tag 'ntb-5.5' of git://github.com/jonmason/ntb
Pull NTB update from Jon Mason:
"Just a simple patch to add a new Hygon Device ID to the AMD NTB device
driver"
* tag 'ntb-5.5' of git://github.com/jonmason/ntb:
NTB: Add Hygon Device ID
Stefano Garzarella
David S. Miller
Russell King
Shahjada Abul Husain
Chen Wandun
Jakub Kicinski
Kuniyuki Iwashima
Michael Walle
Jon Maloy
Nathan Chancellor
Dan Murphy
Kevin(Yudong) Yang
Xin Long
Colin Ian King
Mao Wenan
Jason A. Donenfeld
Linus Torvalds