0x3ff in tun_hashfn is mask of TUN_NUM_FLOW_ENTRIES, instead
of hardcode, define a macro to setup the relationship with
TUN_NUM_FLOW_ENTRIES
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vnic_dev_register(), vnic_rq_alloc_bufs() and vnic_wq_alloc_bufs()
are never called in atomic context.
They call kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These semicolons are not needed. Just remove them.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
variable 'err' is unmodified after initalization,
so simply cleans up it and returns 0.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Applications use -ECONNREFUSED as returned from write() in order to
determine that a socket should be closed. However, when using connected
dgram unix sockets in a poll/write loop, a final POLLOUT event can be
missed when the remote end closes. Thus, the poll is stuck forever:
thread 1 (client) thread 2 (server)
connect() to server
write() returns -EAGAIN
unix_dgram_poll()
-> unix_recvq_full() is true
close()
->unix_release_sock()
->wake_up_interruptible_all()
unix_dgram_poll() (due to the
wake_up_interruptible_all)
-> unix_recvq_full() still is true
->free all skbs
Now thread 1 is stuck and will not receive anymore wakeups. In this
case, when thread 1 gets the -EAGAIN, it has not queued any skbs
otherwise the 'free all skbs' step would in fact cause a wakeup and
a POLLOUT return. So the race here is probably fairly rare because
it means there are no skbs that thread 1 queued and that thread 1
schedules before the 'free all skbs' step.
This issue was reported as a hang when /dev/log is closed.
The fix is to signal POLLOUT if the socket is marked as SOCK_DEAD, which
means a subsequent write() will get -ECONNREFUSED.
Reported-by: Ian Lance Taylor <iant@golang.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the quest to remove all stack VLA usage from the kernel[1], this
removes the discouraged use of AHASH_REQUEST_ON_STACK (and associated
VLA) by switching to shash directly and keeping the associated descriptor
allocated with the regular state on the heap.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Push iov_iter up from rxrpc_kernel_recv_data() to its caller to allow
non-contiguous iovs to be passed down, thereby permitting file reading to
be simplified in the AFS filesystem in a future patch.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: dsa and systemport WoL changes
This patch series extracts what was previously submitted as part of the
"WAKE_FILTER" Wake-on-LAN patch series into patches that do not.
Changes in this series:
- properly align the dsa_is_cpu_port() check in first patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a helper function to turn on/off MPD, this will be used to avoid
duplicating code as we are going to add additional types of wake-up
types.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already properly resume from Wake-on-LAN whether such a condition
occured or not, no need to process the WoL interrupt for functional
changes since that could race with other settings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we are in Wake-on-LAN, we operate with the host sofware not running
a network stack, so we want to the switch to flood packets in order to
cause a system wake-up when matching specific filters (unicast or
multicast). This was not necessary before since we supported Magic
Packet which are targeting a broadcast MAC address which the switch
already floods.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
ds->enabled_port_mask only contains a bitmask of user-facing enabled
ports, we also need to allow programming CFP rules that target CPU ports
(e.g: ports 5 and 8).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault says:
====================
l2tp: sanitise MTU handling on sessions
Most of the code handling sessions' MTU has no effect. The ->mtu field
in struct l2tp_session might be used at session creation time, but
neither PPP nor Ethernet pseudo-wires take updates into account.
L2TP sessions don't have a concept of MTU, which is the reason why
->mtu is mostly ignored. MTU should remain a network device thing.
Therefore this patch set does not try to propagate/update ->mtu to/from
the device. That would complicate the code unnecessarily. Instead this
field and the associated ioctl commands and netlink attributes are
removed.
Patch #1 defines l2tp_tunnel_dst_mtu() in order to simplify the
following patches. Then patches #2 and #3 remove MTU handling from PPP
and Ethernet pseudo-wires respectively.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This attribute's handling is broken. It can only be used when creating
Ethernet pseudo-wires, in which case its value can be used as the
initial MTU for the l2tpeth device.
However, when handling update requests, L2TP_ATTR_MTU only modifies
session->mtu. This value is never propagated to the l2tpeth device.
Dump requests also return the value of session->mtu, which is not
synchronised anymore with the device MTU.
The same problem occurs if the device MTU is properly updated using the
generic IFLA_MTU attribute. In this case, session->mtu is not updated,
and L2TP_ATTR_MTU will report an invalid value again when dumping the
session.
It does not seem worthwhile to complexify l2tp_eth.c to synchronise
session->mtu with the device MTU. Even the ip-l2tp manpage advises to
use 'ip link' to initialise the MTU of l2tpeth devices (iproute2 does
not handle L2TP_ATTR_MTU at all anyway). So let's just ignore it
entirely.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of the session's .mtu field, as defined by
pppol2tp_connect() or pppol2tp_session_create(), is later overwritten
by pppol2tp_session_init() (unless getting the tunnel's socket PMTU
fails). This field is then only used when setting the PPP channel's MTU
in pppol2tp_connect().
Furthermore, the SIOC[GS]IFMTU ioctls only act on the session's .mtu
without propagating this value to the PPP channel, making them useless.
This patch initialises the PPP channel's MTU directly and ignores the
session's .mtu entirely. MTU is still computed by subtracting the
PPPOL2TP_HEADER_OVERHEAD constant. It is not optimal, but that doesn't
really matter: po->chan.mtu is only used when the channel is part of a
multilink PPP bundle. Running multilink PPP over packet switched
networks is certainly not going to be efficient, so not picking the
best MTU does not harm (in the worst case, packets will just be
fragmented by the underlay).
The SIOC[GS]IFMTU ioctls are removed entirely (as opposed to simply
ignored), because these ioctls commands are part of the requests that
should be handled generically by the socket layer. PX_PROTO_OL2TP was
the only socket type abusing these ioctls.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate retrieval of tunnel's socket mtu in order to simplify
l2tp_eth and l2tp_ppp a bit.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Salil Mehta says:
====================
Some important fixes for HNS3 driver
This patch presents some important fixes related to MSIX allocation
in HNS3 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The offset of msix number for roce is different between different
revision id. We should get it from firmware, instead of a fix value.
This patch refines the msix allocation, make it compatible.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The msix number for vf is different, depends on the max vf number.
Futherly if the vf supports roce, the offset of msix is not fixed.
It's incorrect to fix the msix number to 33. This patch fixes it by
querying the msix number from firmware, and adjusting it with roce
support.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of SKCIPHER_REQUEST_ON_STACK() will trigger FRAME_WARN warnings
(when less than 2048) once the VLA is no longer hidden from the check:
net/rxrpc/rxkad.c:398:1: warning: the frame size of 1152 bytes is larger than 1024 bytes [-Wframe-larger-than=]
net/rxrpc/rxkad.c:242:1: warning: the frame size of 1152 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This passes the initial SKCIPHER_REQUEST_ON_STACK allocation to the leaf
functions for reuse. Two requests allocated on the stack is not needed
when only one is used at a time.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User was able to perform filter flush on chain 0 even if it didn't have
any filters in it. With the patch that avoided implicit chain 0
creation, this changed. So in case user wants filter flush on chain
which does not exist, just return success. There's no reason for non-0
chains to behave differently than chain 0, so do the same for them.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: f71e0ca4db ("net: sched: Avoid implicit chain 0 creation")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The else-if branch and else branch set mac_ok to true similarly,
so combine the two into single else branch.
Also add comments to explain the two conditions, which
from Michael Chan and Vasundhara Volam.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 38d5d3b3d5 ("bpf: Introduce BPF_ANNOTATE_KV_PAIR")
added to the bpf and net trees what
commit 92b57121ca ("bpf: btf: export btf types and name by offset from lib")
has already added to bpf-next/net-next, but in slightly different
location. Remove the duplicates (to fix build of libbpf).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This refactoring work has been started by David Howells in cdfbabfb2f
(net: Work around lockdep limitation in sockets that use sockets) but
the exact same day in 581319c586 (net/socket: use per af lockdep
classes for sk queues), Paolo Abeni added new classes.
This reduces the amount of (nearly) duplicated code and eases the
addition of new socket types.
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return statements in functions returning bool should use true or false
instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variables 'max_frm' and 'tmp_mac_key' are being assigned,
but are never used,hence they are redundant and can be removed.
fix fllowing warning:
drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:461:6: warning: variable 'max_frm' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:1685:31: warning: variable 'tmp_mac_key' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:1855:41: warning: variable 'tmp_mac_key' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arun Parameswaran says:
====================
Add clock config and pm support to bcm iProc mdio mux
The patchset extends the Broadcom iProc mdio mux to add support for
suspend/resume and the ability to configure the internal clock
divider. The patchset also sets the scan control register to
disable external master access.
The base address of the mdio-mux-bcm-iproc is modified to point to the
start of the mdio block's address space, to be able to access all the
mdio's registers. The missing registers are required to configure the
internal clock divider registers in some of the Broadcom SoC's.
Changes from v3:
- Removed 'platform_set_drvdata(pdev, NULL)' call (in patch 5/8)
- Fixed the return code handling for the devm_clk_get() call (in patch
7/8)
- Added Reviewed-by tag to Patch 8/8
Changes from v2:
- Addressed Andrew's comments:
- Moved to using devm_mdiobus_alloc. Added this as a separate patch.
- Changed to reverse christmas tree order for variable declaration in
the clock patch
- Addressed Florian's comments:
- Removed null checks for the clock before calling unprepare in
both clock and pm patches.
- Added check for EPROBE_DEFER when fetching the clock in the clock
patch.
- The patch to use the devm API has been added before the clock & pm
patches. This patch is now patch '5' in the series.
- Added reviewed-by tags to commit messages of patches which remain
unmodified from v2.
- Modified PM patch to use platform_get_drvdata() in suspend/resume
API's, similar to the recent fix that went in for the remove()
api.
Changes from v1:
- Addressed Andrew's comments.
- Reworked the patches to be based on 'net-next'
- Removed 'fixes' from the commit messages, the changes are related
to the new features being added.
- Maintained backward compatibility to older dt-blob's specifying
base addresse with an offset. The correction is applied in the
driver and a message is printed to update the dt-blob.
- Re-worked and re-ordered the last four patches (4-7).
- Added setting of the scan control register as a new patch
- Added a call to 'clk_prepare_enable()' in the patch that adds
the clock config support, removed the debug message when clock
is not passed.
- Simplified the pm support patch (removed the array used for the
save/restore logic).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for suspend and resume to the Broadcom iProc mdio
mux driver.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to configure the internal rate adjust register based on the
core clock supplied through device tree in the Broadcom iProc mdio mux.
The operating frequency of the mdio mux block is 11MHz. This is derrived
by dividing the clock to the mdio mux with the rate adjust register.
In some SoC's the default values of the rate adjust register do not yield
11MHz. These SoC's are required to specify the clock via the device tree
for proper operation.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add clock phandle, of the core clock driving the mdio block, as an
optional property to the Broadcom iProc mdio mux.
The clock, when specified, will be used to setup the rate adjust registers
in the mdio to derrive the mdio's operating frequency.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_mdiobus_alloc() instead of mdiobus_alloc() in the Broadcom
iProc mdio mux driver.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure the scan control register in the Broadcom iProc
mdio mux driver to disable access to external master.
In some SoC's, the scan control register defaults to an incorrect
value.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the base address of the mdio mux driver to point to the
start of the mdio mux block's register address space.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the register offsets in the Broadcom iProc mdio mux to start
from the top of the register address space.
Earlier, the base address pointed to the end of the block's register
space. The base address will now point to the start of the mdio's
address space. The offsets have been fixed to match this.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the base address of the Broadcom iProc MDIO mux driver to
point to the start of the block's register address space.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_info message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check DMA addressing limitations as suggested by the DMA API
how-to. This does not fix a particular issue seen but is
considered good style.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
net/rxrpc/proc.c: In function 'rxrpc_call_seq_show':
net/rxrpc/proc.c:66:29: warning:
variable 'nowj' set but not used [-Wunused-but-set-variable]
unsigned long timeout = 0, nowj;
^
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Fixes keep trickling in:
1) Various IP fragmentation memory limit hardening changes from Eric
Dumazet.
2) Revert ipv6 metrics leak change, it causes more problems than it
fixes for now.
3) Fix WoL regression in stmmac driver, from Jose Abreu.
4) Netlink socket spectre v1 gadget fix, from Jeremy Cline"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
Revert "net/ipv6: fix metrics leak"
rxrpc: Fix user call ID check in rxrpc_service_prealloc_one
net: dsa: Do not suspend/resume closed slave_dev
netlink: Fix spectre v1 gadget in netlink_create()
Documentation: dpaa2: Use correct heading adornment
net: stmmac: Fix WoL for PCI-based setups
bonding: avoid lockdep confusion in bond_get_stats()
enic: do not call enic_change_mtu in enic_probe
ipv4: frags: handle possible skb truesize change
inet: frag: enforce memory limits earlier
net/mlx5e: IPoIB, Set the netdevice sw mtu in ipoib enhanced flow
net/mlx5e: Fix null pointer access when setting MTU of vport representor
net/mlx5e: Set port trust mode to PCP as default
net/mlx5e: E-Switch, Initialize eswitch only if eswitch manager
net: dsa: mv88e6xxx: Fix SERDES support on 88E6141/6341
brcmfmac: fix regression in parsing NVRAM for multiple devices
iwlwifi: add more card IDs for 9000 series
Previously in squashfs_readpage() when copying data into the page
cache, it used the length of the datablock read from the filesystem
(after decompression). However, if the filesystem has been corrupted
this data block may be short, which will leave pages unfilled.
The fix for this is to compute the expected number of bytes to copy
from the inode size, and use this to detect if the block is short.
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
Tested-by: Willy Tarreau <w@1wt.eu>
Cc: Анатолий Тросиненко <anatoly.trosinenko@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The squashfs fragment reading code doesn't actually verify that the
fragment is inside the fragment table. The end result _is_ verified to
be inside the image when actually reading the fragment data, but before
that is done, we may end up taking a page fault because the fragment
table itself might not even exist.
Another report from Anatoly and his endless squashfs image fuzzing.
Reported-by: Анатолий Тросиненко <anatoly.trosinenko@gmail.com>
Acked-by:: Phillip Lougher <phillip.lougher@gmail.com>,
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit df18b50448.
This change causes other problems and use-after-free situations as
found by syzbot.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM fix from Russell King:
"Just a single fix this time around for recent binutils causing build
problems when generating Thumb-2 code"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8781/1: Fix Thumb-2 syscall return for binutils 2.29+
Fixes: 83ba464515 ("net: add helpers checking if socket can be bound to nonlocal address")
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2c4541e24c ("mm: use vma_init() to initialize VMAs on stack and
data segments") tried to initialize various left-over ad-hoc vma's
"properly", but actually made things worse for the temporary vma's used
for TLB flushing.
vma_init() doesn't actually initialize all of the vma, just a few
fields, so doing something like
- struct vm_area_struct vma = { .vm_mm = tlb->mm, };
+ struct vm_area_struct vma;
+
+ vma_init(&vma, tlb->mm);
was actually very bad: instead of having a nicely initialized vma with
every field but "vm_mm" zeroed, you'd have an entirely uninitialized vma
with only a couple of fields initialized. And they weren't even fields
that the code in question mostly cared about.
The flush_tlb_range() function takes a "struct vma" rather than a
"struct mm_struct", because a few architectures actually care about what
kind of range it is - being able to only do an ITLB flush if it's a
range that doesn't have data accesses enabled, for example. And all the
normal users already have the vma for doing the range invalidation.
But a few people want to call flush_tlb_range() with a range they just
made up, so they also end up using a made-up vma. x86 just has a
special "flush_tlb_mm_range()" function for this, but other
architectures (arm and ia64) do the "use fake vma" thing instead, and
thus got caught up in the vma_init() changes.
At the same time, the TLB flushing code really doesn't care about most
other fields in the vma, so vma_init() is just unnecessary and
pointless.
This fixes things by having an explicit "this is just an initializer for
the TLB flush" initializer macro, which is used by the arm/arm64/ia64
people who mis-use this interface with just a dummy vma.
Fixes: 2c4541e24c ("mm: use vma_init() to initialize VMAs on stack and data segments")
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Kirill Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Delete the old VM_BUG_ON_VMA() from zap_pmd_range(), which asserted
that mmap_sem must be held when splitting an "anonymous" vma there.
Whether that's still strictly true nowadays is not entirely clear,
but the danger of sometimes crashing on the BUG is now fairly clear.
Even with the new stricter rules for anonymous vma marking, the
condition it checks for can possible trigger. Commit 44960f2a7b
("staging: ashmem: Fix SIGBUS crash when traversing mmaped ashmem
pages") is good, and originally I thought it was safe from that
VM_BUG_ON_VMA(), because the /dev/ashmem fd exposed to the user is
disconnected from the vm_file in the vma, and madvise(,,MADV_REMOVE)
insists on VM_SHARED.
But after I read John's earlier mail, drawing attention to the
vfs_fallocate() in there: I may be wrong, and I don't know if Android
has THP in the config anyway, but it looks to me like an
unmap_mapping_range() from ashmem's vfs_fallocate() could hit precisely
the VM_BUG_ON_VMA(), once it's vma_is_anonymous().
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Kirill Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=pQXe
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-next-20180801' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Development
Here are some patches that add some more tracepoints to AF_RXRPC and fix
some issues therein. The most significant points are:
(1) Display the call timeout information in /proc/net/rxrpc/calls.
(2) Save the call's debug_id in the rxrpc_channel struct so that it can be
used in traces after the rxrpc_call struct has been destroyed.
(3) Increase the size of the kAFS Rx window from 32 to 63 to be about the
same as the Auristor server.
(4) Propose the terminal ACK for a client call after it has received all
its data to be transmitted after a short interval so that it will get
transmitted if not first superseded by a new call on the same channel.
(5) Flush ACKs during the data reception if we detect that we've run out
of data.[*]
(6) Trace successful packet transmission and softirq to process context
socket notification.
[*] Note that on a uncontended gigabit network, rxrpc runs in to trouble
with ACK packets getting batched together (up to ~32 at a time)
somewhere between the IP transmit queue on the client and the ethernet
receive queue on the server.
I can see the kernel afs filesystem client and Auristor userspace
server stalling occasionally on a 512MB single read. Sticking
tracepoints in the network driver at either end seems to show that,
although the ACK transmissions made by the client are reasonably spaced
timewise, the received ACKs come in batches from the network card on
the server.
I'm not sure what, if anything, can be done about this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There just check the user call ID isn't already in use, hence should
compare user_call_ID with xcall->user_call_ID, which is current
node's user_call_ID.
Fixes: 540b1c48c3 ("rxrpc: Fix deadlock between call creation and sendmsg/recvmsg")
Suggested-by: David Howells <dhowells@redhat.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing
Jia-Ju Bai
zhong jiang
YueHaibing
Jason Baron
Kees Cook
David Howells
David S. Miller
Florian Fainelli
Guillaume Nault
Jian Shen
Jiri Pirko
Jakub Kicinski
Matthieu Baerts
Gustavo A. R. Silva
Arun Parameswaran
Colin Ian King
Ganesh Goudar
Stefan Agner
Wei Yongjun
Linus Torvalds
Phillip Lougher
Vincent Bernat
Hugh Dickins