1) For the forward X_calc lookup, it
* protects effectively against RTT=0 (this case is possible), by
returning the maximal lookup value instead of just setting it to 1
* reformulates the array-bounds exceeded condition: this only happens
if p is greater than 1E6 (due to the scaling)
* the case of negative indices can now with certainty be excluded,
since documentation shows that the formulas are within bounds
* additional protection against p = 0 (would give divide-by-zero)
2) For the reverse lookup, it warns against
* protects against exceeding array bounds
* now returns 0 if f(p) = 0, due to function definition
* warns about minimal resolution error and returns the smallest table
value instead of p=0 [this would mask congestion conditions]
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This fixes the following small error in tfrc_calc_x_reverse_lookup.
1) The table is generated by the following equations:
lookup[index][0] = g((index+1) * 1000000/TFRC_CALC_X_ARRSIZE);
lookup[index][1] = g((index+1) * TFRC_CALC_X_SPLIT/TFRC_CALC_X_ARRSIZE);
where g(q) is 1E6 * f(q/1E6)
2) The reverse lookup assigns an entry in lookup[index][small]
3) This index needs to match the above, i.e.
* if small=0 then
p = (index + 1) * 1000000/TFRC_CALC_X_ARRSIZE
* if small=1 then
p = (index+1) * TFRC_CALC_X_SPLIT/TFRC_CALC_X_ARRSIZE
These are exactly the changes that the patch makes; previously the code did
not conform to the way the lookup table was generated (this difference resulted
in a mean error of about 1.12%).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This adds documentation for the TCP Reno throughput equation which is at
the heart of the TFRC sending rate / loss rate calculations.
It spells out precisely how the values were determined and what they mean.
The equations were derived through reverse engineering and found to be
fully accurate (verified using test programs).
This patch does not change any code.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This avoids a (harmless) warning message being printed at the DCCP server
(the receiver of a DCCP half connection).
Incoming packets are both directed to
* ccid_hc_rx_packet_recv() for the server half
* ccid_hc_tx_packet_recv() for the client half
The message gets printed since on a server the client half is currently not
sending data packets.
This is resolved for the moment by checking the DCCP-role first. In future
times (bidirectional DCCP connections), this test may have to be more
sophisticated.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
The main object of this patch is the following bug:
==> In ccid3_hc_tx_packet_recv, the parameters p and X_recv were updated
_after_ the send rate was calculated. This is clearly an error and is
resolved by re-ordering statements.
In addition,
* r_sample is converted from u32 to long to check whether the time difference
was negative (it would otherwise be converted to a large u32 value)
* protection against RTT=0 (this is possible) is provided in a further patch
* t_elapsed is also converted to long, to match the type of r_sample
* adds a a more debugging information regarding current send rates
* various trivial comment/documentation updates
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This bug resulted in ccid3_hc_tx_send_packet returning negative
delay values, which in turn triggered silently dequeueing packets in
dccp_write_xmit. As a result, only a few out of the submitted packets made
it at all onto the network. Occasionally, when dccp_wait_for_ccid was
involved, this also triggered a bug warning since ccid3_hc_tx_send_packet
returned a negative value (which in reality was a negative delay value).
The cause for this bug lies in the comparison
if (delay >= hctx->ccid3hctx_delta)
return delay / 1000L;
The type of `delay' is `long', that of ccid3hctx_delta is `u32'. When comparing
negative long values against u32 values, the test returned `true' whenever delay
was smaller than 0 (meaning the packet was overdue to send).
The fix is by casting, subtracting, and then testing the difference with
regard to 0.
This has been tested and shown to work.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
The TFRC nofeedback timer normally expires after the maximum of 4
RTTs and twice the current send interval (RFC 3448, 4.3). On LANs
with a small RTT this can mean a high processing load and reduced
performance, since then the nofeedback timer is triggered very
frequently.
This patch provides a configuration option to set the bound for the
nofeedback timer, using as default 100 milliseconds.
By setting the configuration option to 0, strict RFC 3448 behaviour
can be enforced for the nofeedback timer.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
aevents can not uniquely identify an SA. We break the ABI with this
patch, but consensus is that since it is not yet utilized by any
(known) application then it is fine (better do it now than later).
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
To use ipv6_find_hdr(), IP6_NF_IPTABLES is necessary.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Binderman's icc logs:
net/rose/rose_route.c(399): remark #593: variable "err" was set but never used
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- move EXPORT_SYMBOL next to exported symbol
- use EXPORT_SYMBOL_GPL since this is what the original code used
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also remove the references to "new connection tracking" from Kconfig.
After some short stabilization period of the new connection tracking
helpers/NAT code the old one will be removed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv4 and IPv6 capable nf_conntrack port of the TFTP conntrack/NAT helper.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv4 and IPv6 capable nf_conntrack port of the SIP conntrack/NAT helper.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nf_conntrack port of the PPtP conntrack/NAT helper. Since there seems
to be no IPv6-capable PPtP implementation the helper only support IPv4.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nf_conntrack port of the NetBIOS name service conntrack helper.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add nf_conntrack port of the IRC conntrack/NAT helper. Since DCC doesn't
support IPv6 yet, the helper is still IPv4 only.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv4 and IPv6 capable nf_conntrack port of the H.323 conntrack/NAT helper.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv4 and IPv6 capable nf_conntrack port of the Amanda conntrack/NAT helper.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expectation address masks need to be differently initialized depending
on the address family, create helper function to avoid cluttering up
the code too much.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add FTP NAT helper.
Split out from Jozsef's big nf_nat patch with a few small fixes by myself.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NAT support for nf_conntrack. Joint work of Jozsef Kadlecsik,
Yasuyuki Kozakai, Martin Josefsson and myself.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve the connection tracking selection (well, the user experience,
not really the aesthetics) by offering one option to enable connection
tracking and a choice between the implementations.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some helpers (namely H.323) manually assign further helpers to expected
connections. This is not possible with nf_conntrack anymore since we
need to know whether a helper is used at allocation time.
Handle the helper assignment centrally, which allows to perform the
correct allocation and as a nice side effect eliminates the need
for the H.323 helper to fiddle with nf_conntrack_lock.
Mid term the allocation scheme really needs to be redesigned since
we do both the helper and expectation lookup _twice_ for every new
connection.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resync with Al Viro's ip_conntrack annotations and fix a missed
spot in ip_nat_proto_icmp.c.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the alignment to the size doesn't make any sense, what it
should do is align the size of the conntrack structure to the
alignment requirements of the helper structure and return an
aligned pointer in nfct_help().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
NF_CONNTRACK_PROC_COMPAT depends on NF_CONNTRACK_IPV4, not NF_CONNTRACK.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accept -1 as delimiter to abort parsing without an error at the first
unknown character. This is needed by the upcoming nf_conntrack SIP
helper, where addresses are delimited by either '\r' or '\n' characters.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not returning -EINVAL, because someone might want to use the value
zero in some future gact_prob algorithm?
Signed-off-by: Kim Nordlund <kim.nordlund@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove assumption that generic netlink commands cannot have dump
completion callbacks.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
All that remained was skb_migrate() and that was overkill
for what the two call sites were trying to do.
Signed-off-by: David S. Miller <davem@davemloft.net>
The tc actions increased the size of struct tc_police, which broke
compatibility with old iproute binaries since both the act_police
and the old NET_CLS_POLICE code check for an exact size match.
Since the new members are not even used, the simple fix is to also
accept the size of the old structure. Dumping is not affected since
old userspace will receive a bigger structure, which is handled fine.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the following unused EXPORT_SYMBOL's:
- sch_api.c: qdisc_lookup
- sch_generic.c: __netdev_watchdog_up
- sch_generic.c: noop_qdisc_ops
- sch_generic.c: qdisc_alloc
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
... and pass just repl->name to translate_table()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can check newinfo->hook_entry[...] instead.
Kill unused argument.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for valid_hooks is redundant (newinfo->hook_entry[i] will
be NULL if bit i is not set). Kill it, kill unused arguments.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since newinfo->hook_table[] already has been set up, we can switch to using
it instead of repl->{hook_info,valid_hooks}.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take intialization of ->hook_entry[...], ->entries_size and ->nentries
over there, pull the check for empty chains into the end of that sucker.
Now it's self-contained, so we can move it up in the very beginning of
translate_table() *and* we can rely on ->hook_entry[] being properly
transliterated after it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's easier to expand the iterator here *and* we'll be able to move all
uses of ebt_replace from translate_table() into this one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split ebt_check_entry_size_and_hooks() in two parts - one that does
sanity checks on pointers (basically, checks that we can safely
use iterator from now on) and the rest of it (looking into details
of entry).
The loop applying ebt_check_entry_size_and_hooks() is split in two.
Populating newinfo->hook_entry[] is done in the first part.
Unused arguments killed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to revisit a chain we'd already finished with during
the check for current hook. It's either instant loop (which
we'd just detected) or a duplicate work.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need that for iterator to work; existing check had been too weak.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to verify that
a) we are not too close to the end of buffer to dereference
b) next entry we'll be checking won't be _before_ our
While we are at it, don't subtract unrelated pointers...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the following possible cleanups:
- make the following needlessly global functions statis:
- ipv4/tcp.c: __tcp_alloc_md5sig_pool()
- ipv4/tcp_ipv4.c: tcp_v4_reqsk_md5_lookup()
- ipv4/udplite.c: udplite_rcv()
- ipv4/udplite.c: udplite_err()
- make the following needlessly global structs static:
- ipv4/tcp_ipv4.c: tcp_request_sock_ipv4_ops
- ipv4/tcp_ipv4.c: tcp_sock_ipv4_specific
- ipv6/tcp_ipv6.c: tcp_request_sock_ipv6_ops
- net/ipv{4,6}/udplite.c: remove inline's from static functions
(gcc should know best when to inline them)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Diego Beltrami <Diego.Beltrami@hiit.fi>
Signed-off-by: Kazunori Miyazawa <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Miika Komu <miika@iki.fi>
Signed-off-by: Diego Beltrami <Diego.Beltrami@hiit.fi>
Signed-off-by: Kazunori Miyazawa <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It just obfuscates the code and adds limited value. And as Adrian
Bunk noticed, it lacked Kconfig help text too, so just kill it.
Signed-off-by: David S. Miller <davem@davemloft.net>
When peeking at the next packet in a child qdisc by calling dequeue/requeue,
the upper qdisc qlen counter may get out of sync in case the requeue fails.
The qdisc and the child qdisc both have their counter decremented, but since
no packet is given to the upper qdisc it won't decrement its counter itself.
requeue should not fail, so this is mostly for "correctness".
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert HTB to use qdisc_tree_decrease_len() and add a callback
for deactivating a class when its child queue becomes empty.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert HFSC to use qdisc_tree_decrease_len() and add a callback
for deactivating a class when its child queue becomes empty.
All queue purging goes through hfsc_purge_queue(), which is used in
three cases: grafting, class creation (when a leaf class is turned
into an intermediate class by attaching a new class) and class
deletion. In all cases qdisc_tree_decrease_len() is needed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the "simple" qdiscs to use qdisc_tree_decrease_qlen() where
necessary:
- all graft operations
- destruction of old child qdiscs in prio, red and tbf change operation
- purging of queue in sfq change operation
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are multiple problems related to qlen adjustment that can lead
to an upper qdisc getting out of sync with the real number of packets
queued, leading to endless dequeueing attempts by the upper layer code.
All qdiscs must maintain an accurate q.qlen counter. There are basically
two groups of operations affecting the qlen: operations that propagate
down the tree (enqueue, dequeue, requeue, drop, reset) beginning at the
root qdisc and operations only affecting a subtree or single qdisc
(change, graft, delete class). Since qlen changes during operations from
the second group don't propagate to ancestor qdiscs, their qlen values
become desynchronized.
This patch adds a function to propagate qlen changes up the qdisc tree,
optionally calling a callback function to perform qdisc-internal
maintenance when the child qdisc becomes empty. The follow-up patches
will convert all qdiscs to use this function where necessary.
Noticed by Timo Steinbach <tsteinbach@astaro.com>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set parent classids in default qdiscs to allow walking up the tree
from outside the qdiscs. This is needed by the next patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlen adjustment should happen immediately in ->delete and not in the
class destroy function because the reference count will not hit zero in
->delete (sch_api holds a reference) but in ->put. Since the qdisc
lock is released between deletion of the class and final destruction
this creates an externally visible error in the qlen counter.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the ranged tag (tag type #5) to the CIPSOv4 protocol.
The ranged tag allows for seven, or eight if zero is the lowest category,
category ranges to be specified in a CIPSO option. Each range is specified by
two unsigned 16 bit fields, each with a maximum value of 65534. The two values
specify the start and end of the category range; if the start of the category
range is zero then it is omitted.
See Documentation/netlabel/draft-ietf-cipso-ipsecurity-01.txt for more details.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
Add support for the enumerated tag (tag type #2) to the CIPSOv4 protocol.
The enumerated tag allows for 15 categories to be specified in a CIPSO option,
where each category is an unsigned 16 bit field with a maximum value of 65534.
See Documentation/netlabel/draft-ietf-cipso-ipsecurity-01.txt for more details.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
The original NetLabel category bitmap was a straight char bitmap which worked
fine for the initial release as it only supported 240 bits due to limitations
in the CIPSO restricted bitmap tag (tag type 0x01). This patch converts that
straight char bitmap into an extensibile/sparse bitmap in order to lay the
foundation for other CIPSO tag types and protocols.
This patch also has a nice side effect in that all of the security attributes
passed by NetLabel into the LSM are now in a format which is in the host's
native byte/bit ordering which makes the LSM specific code much simpler; look
at the changes in security/selinux/ss/ebitmap.c as an example.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
The attached patch adds --snat-arp support, which makes it possible to
change the source mac address in both the mac header and the arp header
with one rule.
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Add new NFLOG target to allow use of nfnetlink_log for both IPv4 and IPv6.
Currently we have two (unsupported by userspace) hacks in the LOG and ULOG
targets to optionally call to the nflog API. They lack a few features,
namely the IPv4 and IPv6 LOG targets can not specify a number of arguments
related to nfnetlink_log, while the ULOG target is only available for IPv4.
Remove those hacks and add a clean way to use nfnetlink_log.
Signed-off-by: Patrick McHardy <kaber@trash.net>
| NEW | UPDATE | DESTROY |
----------------------------------------|
tuples | Y | Y | Y |
status | Y | Y | N |
timeout | Y | Y | N |
protoinfo | S | S | N |
helper | S | S | N |
mark | S | S | N |
counters | F | F | Y |
Leyend:
Y: yes
N: no
S: iif the field is set
F: iif overflow
This patch also replace IPCT_HELPINFO by IPCT_HELPER since we want to
track the helper assignation process, not the changes in the private
information held by the helper.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Check that status flags are available in the netlink message received
to create a new conntrack.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The NAT handling of the SIP helper has a few problems:
- Request headers are only mangled in the reply direction, From/To headers
not at all, which can lead to authentication failures with DNAT in case
the authentication domain is the IP address
- Contact headers in responses are only mangled for REGISTER responses
- Headers may be mangled even though they contain addresses not
participating in the connection, like alternative addresses
- Packets are droppen when domain names are used where the helper expects
IP addresses
This patch takes a different approach, instead of fixed rules what field
to mangle to what content, it adds symetric mapping of From/To/Via/Contact
headers, which allows to deal properly with echoed addresses in responses
and foreign addresses not belonging to the connection.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Not every header has a shortcut, so make them optional instead
of searching for the same string twice.
Signed-off-by: Patrick McHardy <kaber@trash.net>
- Use enum for header field enumeration
- Use numerical value instead of pointer to header info structure to
identify headers, unexport ct_sip_hdrs
- group SIP and SDP entries in header info structure
- remove double forward declaration of ct_sip_get_info
Signed-off-by: Patrick McHardy <kaber@trash.net>
The NAT helpr hooks are protected by RCU, but all of the
conntrack helpers test and use the global pointers instead
of copying them first using rcu_dereference()
Also replace synchronize_net() by synchronize_rcu() for clarity
since sychronizing only with packet receive processing is
insufficient to prevent races.
Signed-off-by: Patrick McHardy <kaber@trash.net>
We usually uses 'xxx_find_get' for function which increments
reference count.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch adds /proc/net/ip_conntrack, /proc/net/ip_conntrack_expect and
/proc/net/stat/ip_conntrack files to keep old programs using them working.
The /proc/net/ip_conntrack and /proc/net/ip_conntrack_expect files show only
IPv4 entries, the /proc/net/stat/ip_conntrack shows global statistics.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Add helper functions for sysctl registration with optional instantiating
of common path elements (like net/netfilter) and use it for support for
automatic registation of conntrack protocol sysctls.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Only update the conntrack timer if there's been at least HZ jiffies since
the last update. Reduces the number of del_timer/add_timer cycles from one
per packet to one per connection per second (plus once for each state change
of a connection)
Should handle timer wraparounds and connection timeout changes.
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Remove unused struct list_head from struct nf_conntrack_l3proto and
nf_conntrack_l4proto as all protocols are kept in arrays, not linked
lists.
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Remove the usage of ASSERT_READ_LOCK/ASSERT_WRITE_LOCK in nf_conntrack,
it didn't do anything, it was just an empty define and it uglified the code.
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Add some more sanity checks when registering/unregistering l3/l4 protocols.
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Rename 'struct nf_conntrack_protocol' to 'struct nf_conntrack_l4proto' in
order to help distinguish it from 'struct nf_conntrack_l3proto'. It gets
rather confusing with 'nf_conntrack_protocol'.
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Place rarely written variables in the read-mostly section by using
__read_mostly
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch splits out L3/L4 protocol handling into its own file
nf_conntrack_proto.c
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch splits out the event cache into its own file
nf_conntrack_ecache.c
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch splits out handling of helpers into its own file
nf_conntrack_helper.c
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch splits out expectation handling into its own file
nf_conntrack_expect.c
Signed-off-by: Martin Josefsson <gandalf@wlug.westbo.se>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch implements a suggestion by Ian McDonald and
1) Avoids tests against negative packet lengths by using unsigned int
for packet payload lengths in the CCID send_packet()/packet_sent() routines
2) As a consequence, it removes an now unnecessary test with regard to `len > 0'
in ccid3_hc_tx_packet_sent: that condition is always true, since
* negative packet lengths are avoided
* ccid3_hc_tx_send_packet flags an error whenever the payload length is 0.
As a consequence, ccid3_hc_tx_packet_sent is never called as all errors
returned by ccid_hc_tx_send_packet are caught in dccp_write_xmit
3) Removes the third argument of ccid_hc_tx_send_packet (the `len' parameter),
since it is currently always set to skb->len. The code is updated with regard
to this parameter change.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This implements the larger-initial-windows feature for CCID 3, as described in
section 5 of RFC 4342. When the first feedback packet arrives, the sender can
send up to 2..4 packets per RTT, instead of just one.
The patch further
* reduces the number of timestamping calls by passing the timestamp value
(which is computed in one of the calling functions anyway) as argument
* renames one constant with a very long name into one which is shorter and
resembles the one in RFC 3448 (t_mbi)
* simplifies some of the min_t/max_t cases where both `x', `y' have the same
type
Commiter note: renamed TFRC_t_mbi to TFRC_T_MBI, to follow Linux coding style.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
To reflect the fact that this now is of no effect, not making apps
stop working, just be warned in the system log.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This removes and cleans up unused variables and structures which have become
unnecessary following the introduction of the EWMA patch to automatically track
the CCID 3 receiver/sender packet sizes `s'.
It deprecates the PACKET_SIZE socket option by returning an error code and
printing a deprecation warning if an application tries to read or write this
socket option.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This corrects the setting of the nofeedback timer with regard to RFC
3448 - previously it was not set to max(4*R, 2*s/X) as specified. Using
the maximum of 1 second as upper bound (as it was done before) can have
detrimental effects, especially if R is small.
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This is in response to a request sent earlier by Eric W. Biederman
and replaces all sysctl numbers for net.dccp.default with CTL_UNNUMBERED.
It has been tested to compile and to work.
Commiter note: I've removed the use of CTL_UNNUMBERED, not setting .ctl_name
sets it to 0, that is the what CTL_UNNUMBERED is, reason is
to avoid unneeded source code cluttering.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch
* removes setting t_RTO in ccid3_hc_tx_init (per [RFC 3448, 4.2], t_RTO is
undefined until feedback has been received);
* makes some trivial changes (updates of comments);
* performs a small optimisation by exploiting that the feedback timeout
uses the value of t_ipi. The way it is done is safe, because the timeouts
appear after the changes to t_ipi, ensuring that up-to-date values are used;
* in ccid3_hc_tx_packet_recv, moves the t_rto statement closer to the calculation
of the next_tmout. This makes the code clearer to read and is also safe, since
t_rto is not updated until the next call of ccid3_hc_tx_packet_recv, and is not
read by the functions called via ccid_wait_for_ccid();
* removes a `max' statement in sk_reset_timer, this is not needed since the timeout
value is always greater than 1E6 microseconds.
* adds `XXX'es to highlight that currently the nofeedback timer is set
in a non-standard way
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch:
* consolidates updating of parameters (t_nom, t_ipi, t_delta) which
need to be updated at the same time, since they are inter-dependent
* removes two inline functions which are no longer needed as a result of
the above consolidation
* resolves a FIXME regarding the re-calculation of t_ipi within the nofeedback
timer, in the state where no feedback has previously been received
* ties updating these parameters to updating the sending rate X, exploiting
that all three parameters in turn depend on X; and using a small optimisation
which can reduce the number of required instructions: only update the three
parameters when X really changes
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch concerns updating the value of the nofeedback timer when no feedback
has been received so far.
Since in this case the value of R is still undefined according to [RFC 3448,
4.2], we can not perform step (3) of [RFC 3448, 4.3]. A clarification is
provided in [RFC 4342, sec. 5], which states that in these cases the nofeedback
timer (still) expires "after two seconds".
Many thanks to Ian McDonald for pointing this out and providing the
clarification.
The patch
* implements [RFC 4342, sec. 5] with regard to the above case
* consolidates handling timer restart by
- adding an appropriate jump label and
- initialising the timeout value
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Might as well make flush notifier prettier when subpolicy used
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch consolidates set/getsockopt code between UDP(-Lite) v4 and 6. The
justification is that UDP(-Lite) is a transport-layer protocol and therefore
the socket option code (at least in theory) should be AF-independent.
Furthermore, there is the following code reduplication:
* do_udp{,v6}_getsockopt is 100% identical between v4 and v6
* do_udp{,v6}_setsockopt is identical up to the following differerence
--v4 in contrast to v4 additionally allows the experimental encapsulation
types UDP_ENCAP_ESPINUDP and UDP_ENCAP_ESPINUDP_NON_IKE
--the remainder is identical between v4 and v6
I believe that this difference is of little relevance.
The advantages in not duplicating twice almost completely identical code.
The patch further simplifies the interface of udp{,v6}_push_pending_frames,
since for the second argument (struct udp_sock *up) it always holds that
up = udp_sk(sk); where sk is the first function argument.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4, IPv6, and DECNet all use struct rta_cacheinfo in a similiar
way, therefore rtnl_put_cacheinfo() is added to reuse code.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The destination PID is passed directly to netlink_unicast()
respectively netlink_multicast().
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This considers the case - ACK received while no packet has been sent
so far. Resolved by printing a (rate-limited) warning message.
Further removes an unnecessary BUG_ON in ccid3_hc_tx_packet_recv,
received feedback on a terminating connection is simply ignored.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch removes a switch statement which is redundant since,
* nothing is done in states TFRC_SSTATE_NO_SENT/TFRC_SSTATE_NO_FBACK
* it is impossible that the function is called in the state TFRC_SSTATE_TERM, since
--the function is called, in dccp_write_xmit, after ccid3_hc_tx_send_packet
--if ccid3_hc_tx_send_packet is called in state TFRC_SSTATE_TERM, it returns
-EINVAL, which means that ccid3_hc_tx_packet_sent will not be called
(compare dccp_write_xmit)
--> therefore, this case is logically impossible
* the remaining state is TFRC_SSTATE_FBACK which conditionally updates t_ipi, t_nom,
and t_delta. This is a no-op, since
--t_ipi only changes when feedback is received
--however, when feedback arrives via ccid3_hc_tx_packet_recv, there is an identical
code block which performs the same set of operations
--performing the same set of operations again in ccid3_hc_tx_packet_sent therefore
does not change anything, since between the time of receiving the last feedback
(and therefore update of t_ipi, t_nom, and t_delta), the value of t_ipi has not
changed
--since t_ipi has not changed, the values of t_delta and t_nom also do not change,
they depend fully on t_ipi
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This resolves an `XXX' in ccid3_hc_tx_send_packet().
The function is only called on Data and DataAck packets and returns a negative
result on zero-sized messages. This is a reasonable policy since CCID 3 is a
congestion-control module and congestion control on zero-sized Data(Ack)
packets is in a way pathological.
The patch uses a more suitable error code for this case, it returns the Posix.1
code `EBADMSG' ("Not a data message") instead of `ENOTCONN'.
As a result of ignoring zero-sized packets, a the condition for a warning
"First packet is data" in ccid3_hc_tx_packet_sent is always satisfied; this
message has been removed since it will always be printed.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This makes some logically equivalent simplifications, by replacing
rc - values plus goto's with direct return statements.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch performs a simplifying (performance) optimisation:
In each call of the inline function ccid3_calc_new_t_ipi(), the state is
tested against TFRC_SSTATE_NO_FBACK. This is expensive when the function
is called very often. A simpler solution, implemented by this patch, is
to adapt the control flow.
Background:
Now that we can stuff bigger ack vectors into options.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Ack vectors grow proportional to the window size. If an ack vector does not fit
into a single option, it must be spread across multiple options. This patch
will allow for windows to grow larger.
Committer note: Simplified the patch a bit, original algorithm kept.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Commiter note:
This was split from Andrea's original patch, in the process I changed the type
of the ackvec index fields to u16 instead of to int and haven't folded
dccp_ackvec_parse with dccp_ackvec_check_rcv_ackno.
Next patch will actually do the insertion of more than one ackvec per packet,
using, initially, up to a max of 2 ackvecs as per Andrea's original patch, then
I'll work on support for larger ackvecs, be it using a sysctl or using
setsockopt.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Commiter note: original patch was splitted.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Extends the netlink interface to support the __le16 type and
converts address addition, deletion and, dumping to use the
new netlink interface.
Fixes multiple occasions of possible illegal memory references
due to not validated netlink attributes.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Log an error if the remote tunnel endpoint is unable to handle
tunneled packets.
Signed-off-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow link-local tunnel endpoints if the underlying link is defined.
Signed-off-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing the mandatory tunnel endpoint checks when the tunnel is set up
isn't enough as interfaces can go up or down and addresses can be
added or deleted after this. The checks need to be done realtime when
the tunnel is processing a packet.
Signed-off-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
A logic bug in tunnel lookup could result in duplicate tunnels when
changing an existing device.
Signed-off-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on Jamal's patch but compiled and even tested. :-)
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
... into anonymous union of __wsum and __u32 (csum and csum_offset resp.)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
... and switch the damn checksum update to something saner
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
... so caller can use ->ipaddr instead of ->ipaddr_h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
... switched to taking and returning pointers to net-endian
sctp_addr resp. Together, since the only user of sctp_find_unmatch_addr()
just passes its value to sctp_make_asconf_update_ip().
sctp_make_asconf_update_ip() is actually endian-agnostic.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
both are done in one go since almost always we have result of
the latter immediately passed to the former. Possibly non-obvious
note: sctp_process_param() is endian-agnostic
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ditto for its only caller (sctp_endpoint_is_peeled_off)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Along with it, statics in input.c that end up calling it
(__sctp_lookup_association, sctp_lookup_association,
__sctp_rcv_init_lookup, __sctp_rcv_lookup). Callers
are adjusted.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only caller (__sctp_rcv_lookup_endpoint()) also switched,
its caller adjusted
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its only use happens on the same host, when it gets quoted back to
us. So we are free to flip to net-endian and avoid extra PITA.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
switched to taking a pointer to net-endian sctp_addr
and a net-endian port number. Instances and callers
adjusted; interestingly enough, the only calls are
direct calls of specific instances - the method is not
used at all.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
instances of ->cmp_addr() are fine with switching both arguments
to net-endian; callers other than in sctp_cmp_addr_exact() (both
as ->cmp_addr(...) and direct calls of instances) adjusted;
sctp_cmp_addr_exact() switched to net-endian itself and adjustment
is done in its callers
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
No actual modifications of method instances are needed -
they don't look at port numbers. Switch callers...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sctp_chunk->source, sctp_sockaddr_entry->a, sctp_transport->ipaddr
and sctp_transport->saddr, maintain them as net-endian mirrors of
their host-endian counterparts.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part 1: rename sctp_chunk->source, sctp_sockaddr_entry->a,
sctp_transport->ipaddr and sctp_transport->saddr (to ..._h)
The next patch will reintroduce these fields and keep them as
net-endian mirrors of the original (renamed) ones. Split in
two patches to make sure that we hadn't forgotten any instanes.
Later in the series we'll eliminate uses of host-endian variants
(basically switching users to net-endian counterparts as we
progress through that mess). Then host-endian ones will die.
Other embedded host-endian sctp_addr will be easier to switch
directly, so we leave them alone for now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Again, invalid sockaddr passed to userland - host-endiand sin_port.
Potential leak, again, but less dramatic than in previous case.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
a) struct sockaddr_storage * passed to sctp_ulpevent_make_peer_addr_change()
actually points at union sctp_addr field in a structure. Then that sucker
gets copied to userland, with whatever junk we might have there.
b) it's actually having host-endian sin_port.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
It expects (and gets) laddr with net-endian sin_port. And then it calls
sctp_bind_addr_match(), which *does* care about port numbers in case of
ipv6 and expects them to be host-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
That's going to be a long series. Introduced temporary helpers
doing copy-and-convert for sctp_addr; they are used to kill
flip-in-place in global data structures and will be used
to gradually push host-endian uses of sctp_addr out of existence.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
also always get __be16 protocol error; switch to SCTP_PERR()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
argument stored for SCTP_CMD_INIT_FAILED is always __be16
(protocol error). Introduced new field and accessor for
it (SCTP_PERR()); switched to their use (from SCTP_U32() and
.u32)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make copy_to_user_policy_type take a type instead a policy and
fix its users to pass the type
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes dependency on buggy rta_buf, fixes a memory corruption bug due to
a unvalidated netlink attribute, and simplifies the code.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one got lost on the way from Ian to Gerrit to me, fix it.
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This removes a non-referenced variable.
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This makes the code of the dccp_probe module more portable.
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This adds documentation to the CCID 3 rx/tx socket fields, plus some
minor re-formatting.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This reaps the benefit of the earlier patch, which changed the type of
CCID 3 states to use enums, in that many conditions are now simplified
and the number of possible (unexpected) values is greatly reduced.
In a few instances, this also allowed to simplify pre-conditions; where
care has been taken to retain logical equivalence.
[DCCP]: Introduce a consistent BUG/WARN message scheme
This refines the existing set of DCCP messages so that
* BUG(), BUG_ON(), WARN_ON() have meaningful DCCP-specific counterparts
* DCCP_CRIT (for severe warnings) is not rate-limited
* DCCP_WARN() is introduced as rate-limited wrapper
Using these allows a faster and cleaner transition to their original
counterparts once the code has matured into a full DCCP implementation.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Previously the transmit queue was unbounded.
This patch:
* puts a limit on transmit queue length
and sends back EAGAIN if the buffer is full
* sets the TX queue length to a sensible default
* implements tx buffer sysctls for DCCP
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This adds a CCID3 debug option to the configuration menu
which is missing in Kconfig, but already used by the code.
CCID 2 already provides such an entry.
To enable debugging, set CONFIG_IP_DCCP_CCID3_DEBUG=y
NOTE: The use of ccid3_{t,r}x_state_name is safe, since
now only enum values can appear.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch
* makes debugging (when configured) work both for static / module build
* provides generic debugging macros for use in other DCCP / CCID modules
* adds missing information about debug parameters to Kconfig
* performs some code tidy-up
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
The audit_enabled flag is used to signal when syscall auditing is to be
performed. While NetLabel uses a Netlink interface instead of syscalls, it is
reasonable to consider the NetLabel Netlink interface as a form of syscall so
pay attention to the audit_enabled flag when generating audit messages in
NetLabel.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
The cipso_v4_doi_search() function behaves the same as cipso_v4_doi_getdef()
but is a local, static function so use it whenever possibile in the CIPSOv4
code base.
Signed-of-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
The CIPSOv4 translated tag #1 mapping does not always return the correct error
code if the desired mapping does not exist; instead of returning -EPERM it
returns -ENOSPC indicating that the buffer is not large enough to hold the
translated value. This was caused by failing to check a specific error
condition. This patch fixes this so that unknown mappings return
-EPERM which is consistent with the rest of the related CIPSOv4 code.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
While the original CIPSOv4 code had provisions for multiple tag types the
implementation was not as great as it could be, pushing a lot of non-tag
specific processing into the tag specific code blocks. This patch fixes that
issue making it easier to support multiple tag types in the future.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
Currently the CIPSOv4 engine does not do any sort of checking when a new DOI
definition is added. The tags are still verified but only as a side effect of
normal NetLabel operation (packet processing, socket labeling, etc.) which
would cause application errors due to the faulty configuration. This patch
adds tag checking when new DOI definition are added allowing us to catch these
configuration problems when they happen.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
Right now the NetLabel code always jumps into the CIPSOv4 layer to determine if
a CIPSO IP option is present. However, we can do this check directly in the
NetLabel code by making use of the CIPSO_V4_OPTEXIST() macro which should save
us a function call in the common case of not having a CIPSOv4 option present.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
The existing netlbl_lsm_secattr struct required the LSM to check all of the
fields to determine if any security attributes were present resulting in a lot
of work in the common case of no attributes. This patch adds a 'flags' field
which is used to indicate which attributes are present in the structure; this
should allow the LSM to do a quick comparison to determine if the structure
holds any security attributes.
Example:
if (netlbl_lsm_secattr->flags)
/* security attributes present */
else
/* NO security attributes present */
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
Currently the NetLabel unlabeled packet accept flag is an atomic type and it
is checked for every non-NetLabel packet which comes into the system but rarely
ever changed. This patch changes this flag to a normal integer and protects it
with RCU locking.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
These are code optimizations which are relevant when dealing with large
windows. They are not coded the way I would like to, but they do the job for
the short-term. This patch should be more neat.
Commiter note: Changed the seqno comparisions to use {after,before}48 to handle
wrapping.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Spotted by Ian McDonald, tentatively fixed by Gerrit Renker:
http://www.mail-archive.com/dccp%40vger.kernel.org/msg00599.html
Rewritten not to unroll sk_receive_skb, in the common case, i.e. no lock
debugging, its optimized away.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch tackles the following problem:
* the ccid3_hc_{t,r}x_sock define ccid3hc{t,r}x_state as `u8', but
in reality there can only be a few, pre-defined enum names
* this necessitates addiditional checking for unexpected values
which would otherwise be caught by the compiler
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
udp_push_pending_frames is only referenced within
net/ipv4/udp.c and hence can remain static.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker
Jamal Hadi Salim
Yasuyuki Kozakai
Alexey Dobriyan
Patrick McHardy
Jozsef Kadlecsik
Kim Nordlund
David S. Miller
Adrian Bunk
Al Viro
Andrew Morton
Miika Komu
Paul Moore
Pablo Neira Ayuso
Bart De Schuymer
Eric Leblond
Martin Josefsson
Arnaldo Carvalho de Melo
Thomas Graf
Andrea Bittau
Ville Nuorvala
Ian McDonald