Only display the TOD information if there is a corresponding
TOD resource.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the xilinx i2c driver parameters to the resource block instead
of hardcoding things in the registration functions.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new added properties are used for configuring burst length.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document the Lantiq Xway SoC series External Bus Unit (ETOP) bindings.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the Lantiq PMAC Device Tree binding documentation to json-schema.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure the burst length in Ethernet drivers. This improves
Ethernet performance by 58%. According to the vendor BSP,
8W burst length is supported by ar9 and newer SoCs.
The NAT benchmark results on xRX200 (Down/Up):
* 2W: 330 Mb/s
* 4W: 432 Mb/s 372 Mb/s
* 8W: 520 Mb/s 389 Mb/s
Tested on xRX200 and xRX330.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the burst length configurable by the drivers.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current definition of 2W burst length is invalid.
This patch fixes it. Current downstream DEU driver doesn't
use DMA. An incorrect burst length value doesn't cause any
errors. This patch also adds other burst length values.
Fixes: dfec1a827d ("MIPS: Lantiq: Add DMA support")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different SoCs have a different number of channels, e.g .:
* amazon-se has 10 channels,
* danube+ar9 have 20 channels,
* vr9 has 28 channels,
* ar10 has 24 channels.
We can read the ID register and, depending on the reported
number of channels, reset the appropriate number of channels.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading the DMA registers immediately after the reset causes
Data Bus Error. Adding a small delay fixes this issue.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building dp83640.c on arch/parisc/ produces a build warning for
PAGE0 being redefined. Since the macro is not used in the dp83640
driver, just make it a comment for documentation purposes.
In file included from ../drivers/net/phy/dp83640.c:23:
../drivers/net/phy/dp83640_reg.h:8: warning: "PAGE0" redefined
8 | #define PAGE0 0x0000
from ../drivers/net/phy/dp83640.c:11:
../arch/parisc/include/asm/page.h:187: note: this is the location of the previous definition
187 | #define PAGE0 ((struct zeropage *)__PAGE_OFFSET)
Fixes: cb646e2b02 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210913220605.19682-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This drops the code setting bit 9 on egress frames on the
Realtek "type A" (RTL8366RB) frames.
This bit was set on ingress frames for unknown reason,
and was set on egress frames as the format of ingress
and egress frames was believed to be the same. As that
assumption turned out to be false, and since this bit
seems to have zero effect on the behaviour of the switch
let's drop this bit entirely.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210913143156.1264570-1-linus.walleij@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This function is called to enable SR-IOV when available,
not enabling interfaces without VFs was a regression.
Fixes: 65161c3555 ("bnx2x: Fix missing error code in bnx2x_iov_init_one()")
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Reported-by: YunQiang Su <wzssyqa@gmail.com>
Tested-by: YunQiang Su <wzssyqa@gmail.com>
Cc: stable@vger.kernel.org
Acked-by: Shai Malin <smalin@marvell.com>
Link: https://lore.kernel.org/r/20210912190523.27991-1-bunk@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On sparc64, __fls() returns an "int", but the drm TTM code expected it
to be "unsigned long" as on x86. As a result, on sparc (and arc, and
m68k) you get build errors because 'min()' checks that the types match.
As suggested by Linus, it can use min_t instead of min to force the type
to be "unsigned int".
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The boot-time allocation interface for memblock is a mess, with
'memblock_alloc()' returning a virtual pointer, but then you are
supposed to free it with 'memblock_free()' that takes a _physical_
address.
Not only is that all kinds of strange and illogical, but it actually
causes bugs, when people then use it like a normal allocation function,
and it fails spectacularly on a NULL pointer:
https://lore.kernel.org/all/20210912140820.GD25450@xsang-OptiPlex-9020/
or just random memory corruption if the debug checks don't catch it:
https://lore.kernel.org/all/61ab2d0c-3313-aaab-514c-e15b7aa054a0@suse.cz/
I really don't want to apply patches that treat the symptoms, when the
fundamental cause is this horribly confusing interface.
I started out looking at just automating a sane replacement sequence,
but because of this mix or virtual and physical addresses, and because
people have used the "__pa()" macro that can take either a regular
kernel pointer, or just the raw "unsigned long" address, it's all quite
messy.
So this just introduces a new saner interface for freeing a virtual
address that was allocated using 'memblock_alloc()', and that was kept
as a regular kernel pointer. And then it converts a couple of users
that are obvious and easy to test, including the 'xbc_nodes' case in
lib/bootconfig.c that caused problems.
Reported-by: kernel test robot <oliver.sang@intel.com>
Fixes: 40caa127f3 ("init: bootconfig: Remove all bootconfig data when the init memory is removed")
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus proposes to revert an accounting for sops objects in
do_semtimedop() because it's really just a temporary buffer
for a single semtimedop() system call.
This object can consume up to 2 pages, syscall is sleeping
one, size and duration can be controlled by user, and this
allocation can be repeated by many thread at the same time.
However Shakeel Butt pointed that there are much more popular
objects with the same life time and similar memory
consumption, the accounting of which was decided to be
rejected for performance reasons.
Considering at least 2 pages for task_struct and 2 pages for
the kernel stack, a back of the envelope calculation gives a
footprint amplification of <1.5 so this temporal buffer can be
safely ignored.
The factor would IMO be interesting if it was >> 2 (from the
PoV of excessive (ab)use, fine-grained accounting seems to be
currently unfeasible due to performance impact).
Link: https://lore.kernel.org/lkml/90e254df-0dfe-f080-011e-b7c53ee7fd20@virtuozzo.com/
Fixes: 18319498fd ("memcg: enable accounting of ipc resources")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Michal Koutný <mkoutny@suse.com>
Acked-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen reported that the build was broken since commit
6d2ef226f2 ("compiler_attributes.h: drop __has_attribute() support for
gcc4"), with errors such as:
include/linux/compiler_attributes.h:296:5: warning: "__has_attribute" is not defined, evaluates to 0 [-Wundef]
296 | #if __has_attribute(__warning__)
| ^~~~~~~~~~~~~~~
make[2]: *** [arch/powerpc/boot/Makefile:225: arch/powerpc/boot/crt0.o] Error 1
But we expect __has_attribute() to always be defined now that we've
stopped using GCC 4.
Linus debugged it to the point of reading the GCC sources, and noticing
that the problem is that __has_attribute() is not defined when
preprocessing assembly files, which is what we're doing here.
Our assembly files don't include, or need, compiler_attributes.h, but
they are getting it unconditionally from the -include in BOOT_CFLAGS,
which is then added in its entirety to BOOT_AFLAGS.
That -include was added in commit 77433830ed ("powerpc: boot: include
compiler_attributes.h") so that we'd have "fallthrough" and other
attributes defined for the C files in arch/powerpc/boot. But it's not
needed for assembly files.
The minimal fix is to move the addition to BOOT_CFLAGS of -include
compiler_attributes.h until after we've copied BOOT_CFLAGS into
BOOT_AFLAGS. That avoids including compiler_attributes.h for asm files,
but makes no other change to BOOT_CFLAGS or BOOT_AFLAGS.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Debugged-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Guangbin Huang says:
====================
PF support get MAC address space assigned by firmware
This series add support PF to get unicast/multicast MAC address space
assigned by firmware for the HNS3 ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The new firmware supports to divides the whole multicast MAC address space
equally to functions of all PFs, and calculates the space size of each PF
according to its function number.
To support this feature, PF driver adds querying multicast MAC address
space size from firmware and limits used number according to space size.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there are two ways for PF to set the unicast MAC address space
size: specified by config parameters in firmware or set to default value.
That's mean if the config parameters in firmware is zero, driver will
divide the whole unicast MAC address space equally to 8 PFs. However, in
this case, the unicast MAC address space will be wasted a lot when the
hardware actually has less then 8 PFs. And in the other hand, if one PF has
much more VFs than other PFs, then each function of this PF will has much
less address space than other PFs.
In order to ameliorate the above two situations, introduce the third way
of unicast MAC address space assignment: firmware divides the whole unicast
MAC address space equally to functions of all PFs, and calculates the space
size of each PF according to its function number. PF queries the space size
by the querying device specification command when in initialization
process.
The third way assignment is lower priority than specified by config
parameters, only if the config parameters is zero can be used, and if
firmware does not support the third way assignment, then driver still
divides the whole unicast MAC address space equally to 8 PFs.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for qca8327 internal phy needed for correct init of the
switch port. It does use the same qca8337 function and reg just with a
different id.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __alloc_frag_align() is short, and only called by two functions,
so inline page_frag_alloc_align() for reduce the overhead of calls.
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
It shouldn't happen, but can happen that readable eeprom size is smaller
than announced. Then we would be stuck in an endless loop here because
after reaching the actual end reads return eeprom.len = 0. I faced this
issue when making a mistake in driver development. Detect this scenario
and return an error.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed "stdbool.h" inclusion in iosm_ipc_imem.h
Fixes: 13bb8429ca ("net: wwan: iosm: firmware flashing and coredump collection")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d7807a9adf.
As mentioned in https://lkml.org/lkml/2021/9/13/1819
5 years old commit 919483096b ("ipv4: fix memory leaks in ip_cmsg_send() callers")
was a correct fix.
ip_cmsg_send() can loop over multiple cmsghdr()
If IP_RETOPTS has been successful, but following cmsghdr generates an error,
we do not free ipc.ok
If IP_RETOPTS is not successful, we have freed the allocated temporary space,
not the one currently in ipc.opt.
Sure, code could be refactored, but let's not bring back old bugs.
Fixes: d7807a9adf ("Revert "ipv4: fix memory leaks in ip_cmsg_send() callers"")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit
time") may directly retrans a multiple segments TSO/GSO packet without
split, Since this commit, we can no longer assume that a retransmitted
packet is a single segment.
This patch fixes the tp->undo_retrans accounting in tcp_sacktag_one()
that use the actual segments(pcount) of the retransmitted packet.
Before that commit (10d3be5692), the assumption underlying the
tp->undo_retrans-- seems correct.
Fixes: 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit time")
Signed-off-by: zhenggy <zhenggy@chinatelecom.cn>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also correct how initialize_dco_operating_mode is called
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we don't need to support new 5.2 functions but different register
addresses
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not need since TCS firmware file will configure it properlly.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a follow-up to beb401ec50 ("r8169: deprecate support for
RTL_GIGA_MAC_VER_27") that came with 5.12. Nobody complained, so let's
remove support for this chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2021-09-14
The following pull-request contains BPF updates for your *net* tree.
We've added 7 non-merge commits during the last 13 day(s) which contain
a total of 18 files changed, 334 insertions(+), 193 deletions(-).
The main changes are:
1) Fix mmap_lock lockdep splat in BPF stack map's build_id lookup, from Yonghong Song.
2) Fix BPF cgroup v2 program bypass upon net_cls/prio activation, from Daniel Borkmann.
3) Fix kvcalloc() BTF line info splat on oversized allocation attempts, from Bixuan Cui.
4) Fix BPF selftest build of task_pt_regs test for arm64/s390, from Jean-Philippe Brucker.
5) Fix BPF's disasm.{c,h} to dual-license so that it is aligned with bpftool given the former
is a build dependency for the latter, from Daniel Borkmann with ACKs from contributors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Guvenc Gulce says:
====================
net/smc: add EID support
please apply the following patch series for smc to netdev's net-next
tree. The series introduce the so called Enterprise ID support for smc
protocol. Including the generic netlink based interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With SMC-Dv2 users can configure if the static system EID should be used
during CLC handshake, or if only user EIDs are allowed.
Add generic netlink support to enable and disable the system EID, and
to retrieve the system EID and its current enabled state.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system EID is retrieved using an registered ISM device each time
when needed. This adds some unnecessary complexity at all places where
the system EID is needed, but no ISM device is at hand.
Simplify the code and save the system EID in a static variable in
smc_ism.c.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMC-Dv2 allows users to define EIDs which allows to create separate
name spaces enabling users to cluster their SMC-Dv2 connections.
Add support for user defined EIDs and extent the generic netlink
interface so users can add, remove and dump EIDs.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul says:
====================
s390/net: updates 2021-09-14
Please apply the following patches to netdev's net-next tree.
Stop using the wrappers in include/linux/pci-dma-compat.h,
and fix warnings about incorrect kernel-doc comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below.
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many comments above functions start with a kernel doc indicator, but
the comments are not using kernel doc style. Get rid of the warnings
by simply removing the indicator.
E.g.:
drivers/s390/net/netiucv.c:1852: warning:
This comment starts with '/**', but isn't a kernel-doc comment.
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many comments above functions start with a kernel doc indicator, but
the comments are not using kernel doc style. Get rid of the warnings
by simply removing the indicator.
E.g.:
drivers/s390/net/lcs.c:2355: warning:
This comment starts with '/**', but isn't a kernel-doc comment.
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many comments above functions start with a kernel doc indicator, but
the comments are not using kernel doc style. Get rid of the warnings
by simply removing the indicator.
E.g.:
drivers/s390/net/ctcm_main.c:979: warning:
This comment starts with '/**', but isn't a kernel-doc comment.
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: spectrum: Adjustments to port split and label port
Jiri says:
This patchset includes patches that prepare the driver to support modular
systems.
PLLP register is introduced to get front panel port label which is no
longer equivalent to "module + 1" for modular systems, where the
numbering is per line card.
So far for all systems all front panel ports had same format and could
be split to the same number of subports. This is no longer true for
modular systems, where every line card can have different types of front
panel ports.
The PMTDB register is introduced to easily query FW for split
capabilities of particular front panel port. It is generic for use in
modular and non-modular systems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not used anymore, remove it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newly introduced PMTDB register is there to provide all needed info
about particular requested port split configuration. Use it instead of
figuring the info out manually in the driver.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PMTDB register allows to query the possible module<->local port
mapping than can be used in PMLP. It does not represent the actual/current
mapping of the local to module. Actual mapping is only defined by PMLP.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of relying on the values coming from the PMLP register, use PLLP
to get the information about port front panel number and split number.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PLLP register returns the mapping from Local Port into Label Port.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During port creation, mlxsw_core_port_init() is called with the front
panel port number and the split port sub-number. Currently, this
information is determined by the driver without firmware assistance.
Subsequent patches are going to query this information from firmware,
but this requires the port to assigned to SWID.
Therefore, move port SWID assignment before mlxsw_core_port_init().
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During port creation, mlxsw_core_port_init() is called with the front
panel port number and the split port sub-number. Currently, this
information is determined by the driver without firmware assistance.
Subsequent patches are going to query this information from firmware,
but this requires the port to be mapped to a module.
Therefore, move port mapping before mlxsw_core_port_init().
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add latest verified version of Nvidia Spectrum-family switch firmware,
for Spectrum (13.2008.3326), Spectrum-2 (29.2008.3326) and Spectrum-3
(30.2008.3326).
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathan Lemon
Aleksander Jan Bajkowski
Randy Dunlap
Linus Walleij
Adrian Bunk
Huang Rui
Linus Torvalds
Vasily Averin
Michael Ellerman
David S. Miller
Guangbin Huang
Ansuel Smith
Yajun Deng
Heiner Kallweit
M Chetan Kumar
Eric Dumazet
zhenggy
Min Li
Karsten Graul
Christophe JAILLET
Heiko Carstens
Jiri Pirko