The Freescale serial port's are pretty much a 16550, however there are
some FSL specific bugs and features. Add a "fsl,ns16550" compatiable
string to allow code to handle those FSL specific issues.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PCI ranges, localbus reg and localbus chip-select 2 range do not match
the memory map setup by bootloader.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 7c4b2f09 (powerpc: Update mpc85xx/corenet 32-bit defconfigs)
accidentally disabled the ePAPR byte channel driver in the defconfig for
Freescale CoreNet platforms.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Systems which use the fsl_pq_mdio driver need to specify an
address for TBI PHY transactions such that the address does
not conflict with any PHYs on the bus (all transactions to
that address are directed to the onboard TBI PHY). The driver
used to scan for a free address if no address was specified,
however this ran into issues when the PHY Lib was fixed so
that all MDIO transactions were protected by a mutex. As it
is, the code was meant to serve as a transitional tool until
the device trees were all updated to specify the TBI address.
The best fix for the mutex issue was to remove the scanning code,
but it turns out some of the newer SoCs have started to omit
the tbi-phy node when SGMII is not being used. As such, these
devices will now fail unless we add a tbi-phy node to the first
mdio controller.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The commit 883c2cfc8bcc0fd00c5d9f596fb8870f481b5bda:
"fix of_flat_dt_is_compatible() to match the full compatible string"
causes silent boot death on the sbc8349 board because it was
just looking for 8349 and not 8349E -- as originally there
were non-E (no SEC/encryption) chips available. Just add the
E to the board detection string since all boards I've seen
were manufactured with the E versions.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is an issue on FSL-BookE 64-bit devices (P5020) in which PCIe
devices that are capable of doing 64-bit DMAs (like an Intel e1000) do
not function and crash the kernel if we have >4G of memory in the system.
The reason is that the existing code only sets up one inbound window for
access to system memory across PCIe. That window is limited to a 32-bit
address space. So on systems we'll end up utilizing SWIOTLB for dma
mappings. However SWIOTLB dma ops implement dma_alloc_coherent() as
dma_direct_alloc_coherent(). Thus we can end up with dma addresses that
are not accessible because of the inbound window limitation.
We could possibly set the SWIOTLB alloc_coherent op to
swiotlb_alloc_coherent() however that does not address the issue since
the swiotlb_alloc_coherent() will behave almost identical to
dma_direct_alloc_coherent() since the devices coherent_dma_mask will be
greater than any address allocated by swiotlb_alloc_coherent() and thus
we'll never bounce buffer it into a range that would be dma-able.
The easiest and best solution is to just make it so that a 64-bit
capable device is able to DMA to any internal system address.
We accomplish this by opening up a second inbound window that maps all
of memory above the internal SoC address width so we can set it up to
access all of the internal SoC address space if needed.
We than fixup the dma_ops and dma_offset for PCIe devices with a dma
mask greater than the maximum internal SoC address.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Unpaired calling of probe_hcall_entry and probe_hcall_exit might happen
as following, which could cause incorrect preempt count.
__trace_hcall_entry => trace_hcall_entry -> probe_hcall_entry =>
get_cpu_var => preempt_disable
__trace_hcall_exit => trace_hcall_exit -> probe_hcall_exit =>
put_cpu_var => preempt_enable
where:
A => B and A -> B means A calls B, but
=> means A will call B through function name, and B will definitely be
called.
-> means A will call B through function pointer, so B might not be
called if the function pointer is not set.
So error happens when only one of probe_hcall_entry and probe_hcall_exit
get called during a hcall.
This patch tries to move the preempt count operations from
probe_hcall_entry and probe_hcall_exit to its callers.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
CC: stable@kernel.org [v2.6.32+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit c55aef0e5b ("powerpc/boot: Change the load address
for the wrapper to fit the kernel") introduced a WARNING to
inform the user that the uncompressed kernel would overlap
the boot uncompressing wrapper code. Change it to an INFO.
I initially thought, this would be a 'WARNING' for the those
boards, where the link_address should be fixed, so that the
user can take actions accordingly.
Changing the same to INFO.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
The MPIC_PRIMARY define was recently made "default" and the meaning was
inverted to MPIC_SECONDARY. This causes compile errors in currituck now, so
fix it to the new manner of allocating mpics.
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
The wrapper code which uncompresses the kernel in case of a 'ppc' boot
is by default loaded at 0x00400000 and the kernel will be uncompressed
to fit the location 0-0x00400000. But with dynamic relocations, the size
of the kernel may exceed 0x00400000(4M). This would cause an overlap
of the uncompressed kernel and the boot wrapper, causing a failure in
boot.
The message looks like :
zImage starting: loaded at 0x00400000 (sp: 0x0065ffb0)
Allocating 0x5ce650 bytes for kernel ...
Insufficient memory for kernel at address 0! (_start=00400000, uncompressed size=00591a20)
This patch shifts the load address of the boot wrapper code to the next
higher MB, according to the size of the uncompressed vmlinux.
With the patch, we get the following message while building the image :
WARN: Uncompressed kernel (size 0x5b0344) overlaps the address of the wrapper(0x400000)
WARN: Fixing the link_address of wrapper to (0x600000)
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Now that we have relocatable kernel, supporting CRASH_DUMP only requires
turning the switches on for UP machines.
We don't have kexec support on 47x yet. Enabling SMP support would be done
as part of enabling the PPC_47x support.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
The following patch adds relocatable kernel support - based on processing
of dynamic relocations - for PPC44x kernel.
We find the runtime address of _stext and relocate ourselves based
on the following calculation.
virtual_base = ALIGN(KERNELBASE,256M) +
MODULO(_stext.run,256M)
relocate() is called with the Effective Virtual Base Address (as
shown below)
| Phys. Addr| Virt. Addr |
Page (256M) |------------------------|
Boundary | | |
| | |
| | |
Kernel Load |___________|_ __ _ _ _ _|<- Effective
Addr(_stext)| | ^ |Virt. Base Addr
| | | |
| | | |
| |reloc_offset|
| | | |
| | | |
| |______v_____|<-(KERNELBASE)%256M
| | |
| | |
| | |
Page(256M) |-----------|------------|
Boundary | | |
The virt_phys_offset is updated accordingly, i.e,
virt_phys_offset = effective. kernel virt base - kernstart_addr
I have tested the patches on 440x platforms only. However this should
work fine for PPC_47x also, as we only depend on the runtime address
and the current TLB XLAT entry for the startup code, which is available
in r25. I don't have access to a 47x board yet. So, it would be great if
somebody could test this on 47x.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Tony Breeds <tony@bakeyournoodle.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
We find the runtime address of _stext and relocate ourselves based
on the following calculation.
virtual_base = ALIGN(KERNELBASE,KERNEL_TLB_PIN_SIZE) +
MODULO(_stext.run,KERNEL_TLB_PIN_SIZE)
relocate() is called with the Effective Virtual Base Address (as
shown below)
| Phys. Addr| Virt. Addr |
Page |------------------------|
Boundary | | |
| | |
| | |
Kernel Load |___________|_ __ _ _ _ _|<- Effective
Addr(_stext)| | ^ |Virt. Base Addr
| | | |
| | | |
| |reloc_offset|
| | | |
| | | |
| |______v_____|<-(KERNELBASE)%TLB_SIZE
| | |
| | |
| | |
Page |-----------|------------|
Boundary | | |
On BookE, we need __va() & __pa() early in the boot process to access
the device tree.
Currently this has been defined as :
#define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) -
PHYSICAL_START + KERNELBASE)
where:
PHYSICAL_START is kernstart_addr - a variable updated at runtime.
KERNELBASE is the compile time Virtual base address of kernel.
This won't work for us, as kernstart_addr is dynamic and will yield different
results for __va()/__pa() for same mapping.
e.g.,
Let the kernel be loaded at 64MB and KERNELBASE be 0xc0000000 (same as
PAGE_OFFSET).
In this case, we would be mapping 0 to 0xc0000000, and kernstart_addr = 64M
Now __va(1MB) = (0x100000) - (0x4000000) + 0xc0000000
= 0xbc100000 , which is wrong.
it should be : 0xc0000000 + 0x100000 = 0xc0100000
On platforms which support AMP, like PPC_47x (based on 44x), the kernel
could be loaded at highmem. Hence we cannot always depend on the compile
time constants for mapping.
Here are the possible solutions:
1) Update kernstart_addr(PHSYICAL_START) to match the Physical address of
compile time KERNELBASE value, instead of the actual Physical_Address(_stext).
The disadvantage is that we may break other users of PHYSICAL_START. They
could be replaced with __pa(_stext).
2) Redefine __va() & __pa() with relocation offset
#ifdef CONFIG_RELOCATABLE_PPC32
#define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) - PHYSICAL_START + (KERNELBASE + RELOC_OFFSET)))
#define __pa(x) ((unsigned long)(x) + PHYSICAL_START - (KERNELBASE + RELOC_OFFSET))
#endif
where, RELOC_OFFSET could be
a) A variable, say relocation_offset (like kernstart_addr), updated
at boot time. This impacts performance, as we have to load an additional
variable from memory.
OR
b) #define RELOC_OFFSET ((PHYSICAL_START & PPC_PIN_SIZE_OFFSET_MASK) - \
(KERNELBASE & PPC_PIN_SIZE_OFFSET_MASK))
This introduces more calculations for doing the translation.
3) Redefine __va() & __pa() with a new variable
i.e,
#define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) + VIRT_PHYS_OFFSET))
where VIRT_PHYS_OFFSET :
#ifdef CONFIG_RELOCATABLE_PPC32
#define VIRT_PHYS_OFFSET virt_phys_offset
#else
#define VIRT_PHYS_OFFSET (KERNELBASE - PHYSICAL_START)
#endif /* CONFIG_RELOCATABLE_PPC32 */
where virt_phy_offset is updated at runtime to :
Effective KERNELBASE - kernstart_addr.
Taking our example, above:
virt_phys_offset = effective_kernelstart_vaddr - kernstart_addr
= 0xc0400000 - 0x400000
= 0xc0000000
and
__va(0x100000) = 0xc0000000 + 0x100000 = 0xc0100000
which is what we want.
I have implemented (3) in the following patch which has same cost of
operation as the existing one.
I have tested the patches on 440x platforms only. However this should
work fine for PPC_47x also, as we only depend on the runtime address
and the current TLB XLAT entry for the startup code, which is available
in r25. I don't have access to a 47x board yet. So, it would be great if
somebody could test this on 47x.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
The following patch implements the dynamic relocation processing for
PPC32 kernel. relocate() accepts the target virtual address and relocates
the kernel image to the same.
Currently the following relocation types are handled :
R_PPC_RELATIVE
R_PPC_ADDR16_LO
R_PPC_ADDR16_HI
R_PPC_ADDR16_HA
The last 3 relocations in the above list depends on value of Symbol indexed
whose index is encoded in the Relocation entry. Hence we need the Symbol
Table for processing such relocations.
Note: The GNU ld for ppc32 produces buggy relocations for relocation types
that depend on symbols. The value of the symbols with STB_LOCAL scope
should be assumed to be zero. - Alan Modra
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alan Modra <amodra@au1.ibm.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
DYNAMIC_MEMSTART(old RELOCATABLE) was restricted only to PPC_47x variants
of 44x. This patch enables DYNAMIC_MEMSTART for 440x based chipsets.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux ppc dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
The current implementation of CONFIG_RELOCATABLE in BookE is based
on mapping the page aligned kernel load address to KERNELBASE. This
approach however is not enough for platforms, where the TLB page size
is large (e.g, 256M on 44x). So we are renaming the RELOCATABLE used
currently in BookE to DYNAMIC_MEMSTART to reflect the actual method.
The CONFIG_RELOCATABLE for PPC32(BookE) based on processing of the
dynamic relocations will be introduced in the later in the patch series.
This change would allow the use of the old method of RELOCATABLE for
platforms which can afford to enforce the page alignment (platforms with
smaller TLB size).
Changes since v3:
* Introduced a new config, NONSTATIC_KERNEL, to denote a kernel which is
either a RELOCATABLE or DYNAMIC_MEMSTART(Suggested by: Josh Boyer)
Suggested-by: Scott Wood <scottwood@freescale.com>
Tested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux ppc dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
As the kernels and initrd's get bigger boot-loaders and possibly
kexec-tools will need to place the initrd outside the RMO. When this
happens we end up with no lowmem and the boot doesn't get very far.
Only use initrd_end as the limit for alloc_bottom if it's inside the
RMO.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We support 16TB of user address space and half a million contexts
so update the comment to reflect this.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit d57af9b (taskstats: use real microsecond granularity for CPU times)
renamed msecs_to_cputime to usecs_to_cputime, but failed to update all
numbers on the way. This causes nonsensical cpu idle/iowait values to be
displayed in /proc/stat (the only user of usecs_to_cputime so far).
This also renames __cputime_msec_factor to __cputime_usec_factor, adapting
its value and using it directly in cputime_to_usecs instead of doing two
multiplications.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
read_n_cells() cannot be marked as .devinit.text since it is referenced
from two functions that are not in that section: of_get_lmb_size() and
hot_add_drconf_scn_to_nid().
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
mark_reserved_regions_for_nid() is only called from do_init_bootmem(),
which is in .init.text, so it must be in the same section to avoid a
section mismatch warning.
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PPC64 uses long long for u64 in the kernel, but powerpc's asm/types.h
prevents 64-bit userland from seeing this definition, instead defaulting
to u64 == long in userspace. Some user programs (e.g. kvmtool) may actually
want LL64, so this patch adds a check for __SANE_USERSPACE_TYPES__ so that,
if defined, int-ll64.h is included instead.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Implement a POWER7 optimised copy_to_user/copy_from_user using VMX.
For large aligned copies this new loop is over 10% faster, and for
large unaligned copies it is over 200% faster.
If we take a fault we fall back to the old version, this keeps
things relatively simple and easy to verify.
On POWER7 unaligned stores rarely slow down - they only flush when
a store crosses a 4KB page boundary. Furthermore this flush is
handled completely in hardware and should be 20-30 cycles.
Unaligned loads on the other hand flush much more often - whenever
crossing a 128 byte cache line, or a 32 byte sector if either sector
is an L1 miss.
Considering this information we really want to get the loads aligned
and not worry about the alignment of the stores. Microbenchmarks
confirm that this approach is much faster than the current unaligned
copy loop that uses shifts and rotates to ensure both loads and
stores are aligned.
We also want to try and do the stores in cacheline aligned, cacheline
sized chunks. If the store queue is unable to merge an entire
cacheline of stores then the L2 cache will have to do a
read/modify/write. Even worse, we will serialise this with the stores
in the next iteration of the copy loop since both iterations hit
the same cacheline.
Based on this, the new loop does the following things:
1 - 127 bytes
Get the source 8 byte aligned and use 8 byte loads and stores. Pretty
boring and similar to how the current loop works.
128 - 4095 bytes
Get the source 8 byte aligned and use 8 byte loads and stores,
1 cacheline at a time. We aren't doing the stores in cacheline
aligned chunks so we will potentially serialise once per cacheline.
Even so it is much better than the loop we have today.
4096 - bytes
If both source and destination have the same alignment get them both
16 byte aligned, then get the destination cacheline aligned. Do
cacheline sized loads and stores using VMX.
If source and destination do not have the same alignment, we get the
destination cacheline aligned, and use permute to do aligned loads.
In both cases the VMX loop should be optimal - we always do aligned
loads and stores and are always doing stores in cacheline aligned,
cacheline sized chunks.
To be able to use VMX we must be careful about interrupts and
sleeping. We don't use the VMX loop when in an interrupt (which should
be rare anyway) and we wrap the VMX loop in disable/enable_pagefault
and fall back to the existing copy_tofrom_user loop if we do need to
sleep.
The VMX breakpoint of 4096 bytes was chosen using this microbenchmark:
http://ozlabs.org/~anton/junkcode/copy_to_user.c
Since we are using VMX and there is a cost to saving and restoring
the user VMX state there are two broad cases we need to benchmark:
- Best case - userspace never uses VMX
- Worst case - userspace always uses VMX
In reality a userspace process will sit somewhere between these two
extremes. Since we need to test both aligned and unaligned copies we
end up with 4 combinations. The point at which the VMX loop begins to
win is:
0% VMX
aligned 2048 bytes
unaligned 2048 bytes
100% VMX
aligned 16384 bytes
unaligned 8192 bytes
Considering this is a microbenchmark, the data is hot in cache and
the VMX loop has better store queue merging properties we set the
breakpoint to 4096 bytes, a little below the unaligned breakpoints.
Some future optimisations we can look at:
- Looking at the perf data, a significant part of the cost when a
task is always using VMX is the extra exception we take to restore
the VMX state. As such we should do something similar to the x86
optimisation that restores FPU state for heavy users. ie:
/*
* If the task has used fpu the last 5 timeslices, just do a full
* restore of the math state immediately to avoid the trap; the
* chances of needing FPU soon are obviously high now
*/
preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5;
and
/*
* fpu_counter contains the number of consecutive context switches
* that the FPU is used. If this is over a threshold, the lazy fpu
* saving becomes unlazy to save the trap. This is an unsigned char
* so that after 256 times the counter wraps and the behavior turns
* lazy again; this to deal with bursty apps that only use FPU for
* a short time
*/
- We could create a paca bit to mirror the VMX enabled MSR bit and check
that first, avoiding multiple calls to calling enable_kernel_altivec.
That should help with iovec based system calls like readv.
- We could have two VMX breakpoints, one for when we know the user VMX
state is loaded into the registers and one when it isn't. This could
be a second bit in the paca so we can calculate the break points quickly.
- One suggestion from Ben was to save and restore the VSX registers
we use inline instead of using enable_kernel_altivec.
[BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC]
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As of commit dd472da38, rwsem.h was moved into asm-generic.
This patch removes the arch file and points the build at
its new location.
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The code for "powersurge" SMP would kick in and cause a crash
at boot due to the lack of a NULL test.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In the old days, we treated all interrupts from the legacy Apple home made
interrupt controllers as level, with a trick reading the "level" register
along with the "event" register to work arounds bugs where it would
occasionally fail to latch some events.
Doing so appeared to work fine for both level and edge interrupts.
Later on, we discovered in Darwin source the magic masks that define which
interrupts are actually level and which are edge, and implemented a
different algorithm, more similar to what Apple does, that treats those
differently.
I recently discovered however that this caused problems (including loss
of interrupts) with an old Wallstreet PowerBook when trying to use the
internal modem (connected to a cascaded controller).
It looks like some interrupts are treated as edge while they are really
level and I'm starting to seriously doubt the correctness of the Darwin
code (which has other obvious bugs when you read it, so ...)
This patch reverts to our original behaviour of treating everything as
a level interrupt. It appears to solve the problems with the modem on
the Wallstreet and everything else seems to be working properly as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The upcomming currituck patches will need to do 64-bit shifts which will
fail with undefined symbol without this patch.
I looked at linking against libgcc but we can't guarantee that libgcc
was compiled with soft-float. Also Using ../lib/div64.S or
../kernel/misc_32.S, this will break the build as the .o's need to be
built with different flags for the bootwrapper vs the kernel. So for
now the easyest option is to just copy code from
arch/powerpc/kernel/misc_32.S I don't think this code changes too often ;P
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
CONFIG_PPC47x doesn't exist in Kconfig and no 476 processor calls this
function ppc44x_pin_tlb() as it has it's own ppc47x_pin_tlb().
This code is probably an artifact of the original 476 code that
shouldn't have made it upstream.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Needed if you want to use swiotlb, harmless otherwise.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Currituck doesn't need nor use SDR so aborting the pci setup if there is
no sdr-base would be bad.
Add a flag to ppc4xx_pciex_hwops for the backends to state if they need
SDR and then only complain and abort if they do and it's not found in
the device tree.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Most distros use it so we may as well enable it and get regular compile
testing.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When issuing a system reset we almost always oops in the oops_to_nvram
code because multiple CPUs are using the deflate work area. Add a
spinlock to protect it.
To play it safe I'm using trylock to avoid locking up if the NVRAM
code oopses. This means we might miss multiple CPUs oopsing at exactly
the same time but I think it's best to play it safe for now. Once we
are happy with the reliability we can change it to a full spinlock.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This fixes a problem where a CPU thread coming out of nap mode can
think it has valid values in the nonvolatile GPRs (r14 - r31) as saved
away in power7_idle, but in fact the values have been trashed because
the thread was used for KVM in the mean time. The result is that the
thread crashes because code that called power7_idle (e.g.,
pnv_smp_cpu_kill_self()) goes to use values in registers that have
been trashed.
The bit field in SRR1 that tells whether state was lost only reflects
the most recent nap, which may not have been the nap instruction in
power7_idle. So we need an extra PACA field to indicate that state
has been lost even if SRR1 indicates that the most recent nap didn't
lose state. We clear this field when saving the state in power7_idle,
we set it to a non-zero value when we use the thread for KVM, and we
test it in power7_wakeup_noloss.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
At present, on the powernv platform, if you off-line a CPU that was
online, and then try to on-line it again, the kernel generates a
warning message "OPAL Error -1 starting CPU n". Furthermore, if the
CPU is a secondary thread that was used by KVM while it was off-line,
the CPU fails to come online.
The first problem is fixed by only calling OPAL to start the CPU the
first time it is on-lined, as indicated by the cpu_start field of its
PACA being zero. The second problem is fixed by restoring the
cpu_start field to 1 instead of 0 when using the CPU within KVM.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The minimum RMO size field in ibm,client-architecture is currently
ignored, but a future firmware version will rectify that. Since we
always get at least 128MB of RMO right now, asking for 64MB is
likely to result in boot failures.
We should bump it to at least 128MB, but considering all the boot
issues we have on 128MB RMO boxes and all new machines have virtual
RMO, we may as well set our minimum to 256MB.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With CONFIG_STRICT_DEVMEM=y, user space cannot read any part of /dev/mem.
Since this breaks librtas, punch a hole in /dev/mem to allow access to the
rmo_buffer that librtas needs.
Anton Blanchard reported the problem and helped with the fix.
A quick test for this patch:
# cat /proc/rtas/rmo_buffer
000000000f190000 10000
# python -c "print 0x000000000f190000 / 0x10000"
3865
# dd if=/dev/mem of=/tmp/foo count=1 bs=64k skip=3865
1+0 records in
1+0 records out
65536 bytes (66 kB) copied, 0.000205235 s, 319 MB/s
# dd if=/dev/mem of=/tmp/foo
dd: reading `/dev/mem': Operation not permitted
0+0 records in
0+0 records out
0 bytes (0 B) copied, 0.00022519 s, 0.0 kB/s
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
So I've had one of these for a while and it looks like the vendor never
bothered submitting the support upstream.
This adds it using ppc40x_simple and provides a device-tree.
There are some changes to the boot wrapper because the way u-boot works
on this thing, it seems to expect a multipart image with the kernel,
initrd and dtb in it.
The USB support is missing as it needs the yet unmerged driver for
the DWC OTG part and the GPIOs may need further definition in the dts.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Refresh ps3_defconfig to latest kernel sources and
change the options:
CONFIG_PPP=m to CONFIG_PPP=n.
CONFIG_NAMESPACES=y to CONFIG_NAMESPACES=n
CONFIG_NUMA=y to CONFIG_NUMA=n
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add an __init annotation to the ps3_smp_probe() routine.
Fixes build warnings like these when
CONFIG_DEBUG_SECTION_MISMATCH=y:
WARNING: Section mismatch in reference from the function .ps3_smp_probe()
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix some PS3 repository.c build warnings when DEBUG is
defined. Also change most pr_debug calls to pr_devel calls.
Fixes warnings like these:
format '%lx' expects type 'long unsigned int', but argument 7 has type 'u64'
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kumar Gala
Timur Tabi
Andy Fleming
Paul Gortmaker
Li Zhong
Suzuki Poulose
Josh Boyer
Benjamin Herrenschmidt
Paul Mackerras
Anton Blanchard
Andreas Schwab
David Rientjes
Matt Evans
Richard Kuo
Tony Breeds
Christoph Egger
sukadev@linux.vnet.ibm.com
Geoff Levand