USB 3.0 devices may optionally support a new feature called Latency
Tolerance Messaging. If both the xHCI host controller and the device
support LTM, it should be turned on in order to give the system hardware
a better clue about the latency tolerance values of its PCI devices.
Once a Set Feature request to enable LTM is received, the USB 3.0 device
will begin to send LTM updates as its buffers fill or empty, and it can
tolerate more or less latency.
The USB 3.0 spec, section C.4.2 says that LTM should be disabled just
before the device is placed into suspend. Then the device will send an
updated LTM notification, so that the system doesn't think it should
remain in an active state in order to satisfy the latency requirements
of the suspended device.
The Set and Clear Feature LTM enable command can only be sent to a
configured device. The device will respond with an error if that
command is sent while it is in the Default or Addressed state. Make
sure to check udev->actconfig in usb_enable_ltm() and usb_disable_ltm(),
and don't send those commands when the device is unconfigured.
LTM should be enabled once a new configuration is installed in
usb_set_configuration(). If we end up sending duplicate Set Feature LTM
Enable commands on a switch from one installed configuration to another
configuration, that should be harmless.
Make sure that LTM is disabled before the device is unconfigured in
usb_disable_device(). If no drivers are bound to the device, it doesn't
make sense to allow the device to control the latency tolerance of the
xHCI host controller.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Some xHCI host controllers may have optional support for Latency
Tolerance Messaging (LTM). This allows USB 3.0 devices that support LTM
to pass information about how much latency they can tolerate to the xHC.
A PCI xHCI host will use this information to update the PCI Latency
Tolerance Request (LTR) info. The goal of this is to gather latency
information for the system, to enable hardware-driven C states, and the
shutting down of PLLs.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
hub_initiated_lpm_disable_count is not used by any code, so remove it.
This commit should be backported to kernels as old as 3.5, that contain
the commit 8306095fd2 "USB: Disable USB
3.0 LPM in critical sections."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
When a user runs `echo 0 > bConfigurationValue` for a USB 3.0 device,
usb_disable_device() is called. This function disables all drivers,
deallocates interfaces, and sets the device configuration value to 0
(unconfigured).
With the new scheme to ensure that unconfigured devices have LPM
disabled, usb_disable_device() must call usb_unlocked_disable_lpm() once
it unconfigures the device.
This commit should be backported to kernels as old as 3.5, that contain
the commit 8306095fd2 "USB: Disable USB
3.0 LPM in critical sections."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The USB 3.0 Set/Clear Feature U1/U2 Enable cannot be sent to a device in
the Default or Addressed state. It can only be sent to a configured
device. Change the USB core to initialize the LPM disable count to 1
(disabled), which reflects this limitation.
Change usb_set_configuration() to ensure that if the device is
unconfigured on entry, usb_lpm_disable() is not called. This avoids
sending the Clear Feature U1/U2 when the device is in the Addressed
state. When usb_set_configuration() exits with a successfully installed
configuration, usb_lpm_enable() will be called.
Once the new configuration is installed, make sure
usb_set_configuration() only calls usb_enable_lpm() if the device moved
to the Configured state. If we have unconfigured the device by sending
it a Set Configuration for config 0, don't enable LPM.
This commit should be backported to kernels as old as 3.5, that contain
the commit 8306095fd2 "USB: Disable USB
3.0 LPM in critical sections."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The USB 3.0 specification says that sending a Set Feature or Clear
Feature for U1/U2 Enable is not a valid request when the device is in
the Default or Addressed state. It is only valid when the device is in
the Configured state.
The original LPM patch attempted to disable LPM after the device had
been reset by hub_port_init(), before it had the configuration
reinstalled. The TI hub I tested with did not fail the Clear Feature
U1/U2 Enable request that khubd sent while it was in the addressed
state, which is why I didn't catch it.
Move the LPM disable before the device reset, so that we can send the
Clear Feature U1/U2 Enable successfully, and balance the LPM disable
count.
Also delete any calls to usb_enable_lpm() on error paths that lead to
re-enumeration. The calls will fail because the device isn't
configured, and it's not useful to balance the LPM disable count because
the usb_device is about to be destroyed before re-enumeration.
Fix the early exit path ("done" label) to call usb_enable_lpm() to
balance the LPM disable count.
Note that calling usb_reset_and_verify_device() with an unconfigured
device may fail on the first call to usb_disable_lpm(). That's because
the LPM disable count is initialized to 0 (LPM enabled), and
usb_disable_lpm() will attempt to send a Clear Feature U1/U2 request to
a device in the Addressed state. The next patch will fix that.
This commit should be backported to kernels as old as 3.5, that contain
the commit 8306095fd2 "USB: Disable USB
3.0 LPM in critical sections."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This patch (as1564c) converts the EHCI platform drivers to use the
central ehci_setup() routine for generic controller initialization
rather than each having its own idiosyncratic approach.
The major point of difficulty lies in ehci-pci's many vendor- and
device-specific workarounds. Some of them have to be applied before
calling ehci_setup() and some after, which necessitates a fair amount
of code motion. The other platform drivers require much smaller
changes.
One point not addressed by the patch is whether ports should be
powered on or off following initialization. The different drivers
appear to handle this pretty much at random. In fact it shouldn't
matter, because the hub driver turns on power to all ports when it
binds to the root hub. Straightening that out will be left for
another day.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch supports only the host-mode functionality so far.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Tested-by: Subodh Nijsure <snijsure@grid-net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mxs phy is used in Freescale i.MX SoCs, for example
imx23, imx28, imx6Q. This patch adds the basic host
support.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peter Chen <peter.chen@freescale.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Subodh Nijsure <snijsure@grid-net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes, the driver bindings may know what phy they use.
For example, when using device tree, the usb controller may have a
phandler pointing to usb phy.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Subodh Nijsure <snijsure@grid-net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This let usb phy driver has a chance to change hw settings when connect
status change.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Subodh Nijsure <snijsure@grid-net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use ida_simple_get and ida_simple_remove to manage the ids.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platform drivers do the similar things to add/remove ci13xxx device, so
create a unified one.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct ci13xxx represent the controller, which may be device or host,
so name its variables as ci.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch used dmaengine helper functions instead of using hand setting.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed a mistake in the merge conflict resoultion commit(ff9cce) in file
twl6030-usb.c
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't support sg for isoc transfers, enforce this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1563) removes a lot of duplicated code by moving the
EHCI controller suspend/resume routines into the core driver, where
the various platform drivers can invoke them as needed.
Not only does this simplify these platform drivers, this also makes it
easier for other platform drivers to add suspend/resume support in the
future.
Note: The patch does not touch the ehci-fsl.c file, because its
approach to suspend and resume is so different from all the others.
It will have to be handled specially by its maintainer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to convert port_owners type from void * to struct dev_state *
in order to make code more readable.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch rename struct ci13xxx_udc_driver and var with the type.
ci13xxx_platform_data reflect it's passed from platfrom driver.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
allow this driver to be removed too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functional changes, it will just free up some
code if we don't have hotplug.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
msm glue layer compiles on all arches just
fine. Let's drop the unnecessary ARCH check
so we have easier compile tests.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As reported by Dan Carpenter, there is a NULL check in udc_start() that
follows a dereference of the pointer that's being checked. However, at
that point udc pointer shouldn't ever be NULL and if it is, the dereference
should cause an oops.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using urb->transfer_buffer we need to allocate physical contiguous buffers
for the entire transfer, which is pretty much guaranteed to fail with large
transfers.
Currently userspace works around this by breaking large transfers into multiple
urbs. For large bulk transfers this leads to all kind of complications.
This patch makes it possible for userspace to reliable submit large bulk
transfers to scatter-gather capable host controllers in one go, by using a
scatterlist to break the transfer up in managable chunks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few (new) usbdevfs capabilities which an application cannot
discover in any other way then checking the kernel version. There are 3
problems with this:
1) It is just not very pretty.
2) Given the tendency of enterprise distros to backport stuff it is not
reliable.
3) As discussed in length on the mailinglist, USBDEVFS_URB_BULK_CONTINUATION
does not work as it should when combined with USBDEVFS_URB_SHORT_NOT_OK
(which is its intended use) on devices attached to an XHCI controller.
So the availability of these features can be host controller dependent,
making depending on them based on the kernel version not a good idea.
This patch besides adding the new ioctl also adds flags for the following
existing capabilities:
USBDEVFS_CAP_ZERO_PACKET, available since 2.6.31
USBDEVFS_CAP_BULK_CONTINUATION, available since 2.6.32, except for XHCI
USBDEVFS_CAP_NO_PACKET_SIZE_LIM, available since 3.3
Note that this patch only does not advertise the USBDEVFS_URB_BULK_CONTINUATION
cap for XHCI controllers, bulk transfers with this flag set will still be
accepted when submitted to XHCI controllers.
Returning -EINVAL for them would break existing apps, and in most cases the
troublesome scenario wrt USBDEVFS_URB_SHORT_NOT_OK urbs on XHCI controllers
will never get hit, so this would break working use cases.
The disadvantage of not returning -EINVAL is that cases were it is causing
real trouble may go undetected / the cause of the trouble may be unclear,
but this is the best we can do.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iso data buffers may have holes in them if some packets were short, so for
iso urbs we should always copy the entire buffer, just like the regular
processcompl does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed coding style issue related to
prohibited space in drivers/usb/class/cdc-acm.c
Signed-off-by: Jeffrin Jose <ahiliation@yahoo.co.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devm_ functions allocate memory that is released when a driver
detaches. This makes the code smaller and a bit simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devm_ functions allocate memory that is released when a driver
detaches. This makes the code smaller and a bit simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds clock gating to suspend and resume functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are starting to support multiple USB phys as
we should thanks for Kishon's work. DeviceTree support
for USB PHYs won't come until discussion with DeviceTree
maintainer is finished.
Together with that series, we have one fix for twl4030
which missed a IRQF_ONESHOT annotation when requesting
a threaded IRQ without a top half handler, and removal
of an unused variable compilation warning to isp1301_omap.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HwsA
-----END PGP SIGNATURE-----
Merge tag 'xceiv-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: phy: patches for v3.6 merge window
We are starting to support multiple USB phys as
we should thanks for Kishon's work. DeviceTree support
for USB PHYs won't come until discussion with DeviceTree
maintainer is finished.
Together with that series, we have one fix for twl4030
which missed a IRQF_ONESHOT annotation when requesting
a threaded IRQ without a top half handler, and removal
of an unused variable compilation warning to isp1301_omap.
lots of changes for the dwc3 driver which will make
the driver a lot more stable and some changes which
are just cosmetic.
The bulk of changes is related to mis-defined macros
which were never used before, some fixes to error path
which e.g. prevent the driver from initiating two
transfer on ep0out in case of stall, some fixes to
request dequeueing and the End Transfer Command.
We have some changes to U1/U2 handling where we were
enabling those transtions at the wrong spot (though
we haven't seen a problem from that as of today).
A few patches will make it easier to add support for
newer releases of the core by adding definitions for
new registers and changing the code to act accordingly
when certain revisions are detected.
There's also the usual comestic changes to make the
driver easier to maintain and make it easier for new-
comers to understand the driver. Also one patch fixing
a double inclusion of a header.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=s04u
-----END PGP SIGNATURE-----
Merge tag 'dwc3-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: dwc3: patches for v3.6 merge window
lots of changes for the dwc3 driver which will make
the driver a lot more stable and some changes which
are just cosmetic.
The bulk of changes is related to mis-defined macros
which were never used before, some fixes to error path
which e.g. prevent the driver from initiating two
transfer on ep0out in case of stall, some fixes to
request dequeueing and the End Transfer Command.
We have some changes to U1/U2 handling where we were
enabling those transtions at the wrong spot (though
we haven't seen a problem from that as of today).
A few patches will make it easier to add support for
newer releases of the core by adding definitions for
new registers and changing the code to act accordingly
when certain revisions are detected.
There's also the usual comestic changes to make the
driver easier to maintain and make it easier for new-
comers to understand the driver. Also one patch fixing
a double inclusion of a header.
This is quite a big pull request and contains patches
all over the place.
omap_udc is now a bit cleaner after removing omap2 support,
fixing some checkpatch.pl warnings and errors, switching over
to generic map/unmap routines and preventing a NULL pointer
de-reference.
s3c-hsotg has been switched over to devm_* API, got some
locking fixes and improvements and it also got an implementation
for the pullup() method.
the mass storage gadgets changed default value of the removable
parameter, dropped some unused options and made "file" and "ro"
module_parameters read-only in some cases.
ffs function got support for HID descriptor.
Some UDCs have been converted to clk_prepare_enable() and
clk_disable_unprepare().
Marvell now got support for its USB3 controller in mainline
after introducing its mv_u3d_core.c driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=hbE6
-----END PGP SIGNATURE-----
Merge tag 'gadget-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: gadget: patches for v3.6 merge window
This is quite a big pull request and contains patches
all over the place.
omap_udc is now a bit cleaner after removing omap2 support,
fixing some checkpatch.pl warnings and errors, switching over
to generic map/unmap routines and preventing a NULL pointer
de-reference.
s3c-hsotg has been switched over to devm_* API, got some
locking fixes and improvements and it also got an implementation
for the pullup() method.
the mass storage gadgets changed default value of the removable
parameter, dropped some unused options and made "file" and "ro"
module_parameters read-only in some cases.
ffs function got support for HID descriptor.
Some UDCs have been converted to clk_prepare_enable() and
clk_disable_unprepare().
Marvell now got support for its USB3 controller in mainline
after introducing its mv_u3d_core.c driver.
Just two patches here:
First we have a fix to disable DMA in case DMA channel
request fails.
Second, there's a fix for situations where the user
kills musb (by rmmod or any other means) while a
transfer is on the fly. In such cases, we could be
led into a NULL pointer dereference due to endpoint
being disabled and endpoint descriptor being NULL.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=4uPD
-----END PGP SIGNATURE-----
Merge tag 'musb-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: musb: patches for v3.6 merge window
Just two patches here:
First we have a fix to disable DMA in case DMA channel
request fails.
Second, there's a fix for situations where the user
kills musb (by rmmod or any other means) while a
transfer is on the fly. In such cases, we could be
led into a NULL pointer dereference due to endpoint
being disabled and endpoint descriptor being NULL.
spin_unlock_irqrestore() was not being called in the error path of
usb_get_phy. It's fixed here.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
usb_get_phy will return -ENODEV if it's not able to find the phy. Hence
fixed all the callers of usb_get_phy to check for this error condition
instead of relying on a non-zero value as success condition.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fill dev.of_node of gadget drivers, so they can use devicetree
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fill dev.of_node of gadget drivers, so they can use devicetree
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fill dev.of_node of gadget drivers, so they can use devicetree
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fill dev.of_node of gadget drivers, so they can use devicetree
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The “file” sysfs entry for LUNs was writable even for non-removable
LUNs and the fsg_store_file() function did not check whether LUN is
removable or not. This made it possible to change or even close
LUN's backing file.
The same is true for “ro” sysfs entry and LUNs simulating CD-ROM.
For those LUNs, the file should not be writable.
This commit introduces two new device_attribute structures for those
two special cases so that the file/ro sysfs entries are made
non-writable when not desired.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Although timeout has never been experienced, still to make it
meaningful, its better to return error if it ever occurs.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As per databook, ACCEPT{U1,U2}ENA bits should be set after receiving
SetConfiguration Command.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
as per databook, these bits are cleared by hardware on each USB reset,
so no need to clear it explicitly by software in reset ISR.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
as per data book any HIRD threshold value greater than 4b1100 is
invalid. So set the maximum valid value as default values.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
set_halt for ep0 is called to stall a deferred control responses by the
gadget. We already have a function to stall default control endpoint.
This patch points set_halt for ep0 to the already available function.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Michel Sanches <michel.sanches@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sarah Sharp
Alan Stern
Richard Zhao
Kuninori Morimoto
Kishon Vijay Abraham I
Hans de Goede
Lan Tianyu
Felipe Balbi
Alexander Shishkin
Jeffrin Jose
Jingoo Han
Greg Kroah-Hartman
Alexandre Pereira da Silva
Michal Nazarewicz
Pratyush Anand
Linus Torvalds