Removing unused code as FW does not need any value in mbox-5.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
While unloading driver MBOX 0x31 fail as DDB logout (MBOX 0x56)
operation is not completed.
Fix:
Wait for DDB Logout completion before MBOX 0x31
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
Driver holds rom-lock for too long during reset recovery.
During adapter reset testing, it was found that the driver
holds the rom-lock for too long, because of which other
drivers fail to acquire the rom-lock, leading to reset
failures.
The primary cause is, in the bootstrap code, while
holding the rom-lock, the driver checks if the peg is
halted, causing a 2 second contention.
Fix:
When a reset recovery starts, the driver deduces the cause, and
sets appropriate flags in watchdog & recover_adapter routines.
This flag should be used to determine if bootstrap is invoked
from probe or reset context, reducing the rom-lock footprint of
the drivers.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
minidump data collection fails as driver reports data mismatch
Fix:
When the driver encounters a new entry type that it cannot process,
it should just skip the entry and adjust the total buffer size by
subtracting the skipped bytes from it. This is to ensure that there
is no data mismatch because of the new entries.
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
Pending IO wait does not complete after triggering Graceful reset,
causing ack timeout and call traces.
Fix:
1. Reducing the IO command wait timeout before triggering reset,
as logically also timeout should be less than reset timeout (10sec).
2. Moving the abort IO after chip reset, because only after
chip reset, driver owns the IO otherwise it is with firmware and can
still revert back with response.
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
While booting with kdump kernel, driver receive IOCB interrupts
for which it is not ready which results in processing them
before init_firmware during driver probe
Fix:
Two steps solution
1. Make driver ready to process the interrupt before interupts
handlers is registered.
2. Stop driver processing iocb interrupts if not generated as per
firmware protocol i.e R2H bit set
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
Mailbox command 0x102 (IDC Time Extend) failure seen while applying
changes to iface using iscsiadm
Fix:
Added fix to extend IDC timeout only for ISP84xx when IDC ACK
needs to be posted and disable ACB mailbox command completion
is in intermediate state.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
qla4xxx Unable to clear DDB indices when logout fails due to
failure of connection close mbox command.
Root cause:
If login to session fail, iscsiadm make call to destroy_session.
qla4xxx driver does not free ddb index map before free_ddb()
Fix:
Clear DDB Index map before free_ddb in "destroy_session"
in case of connection close mailbox command failure with 4005h.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If waiting for signals was interrupted then the device was put to
FAILED state. Use msleep instead of msleep_interruptible to handle
this correctly.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Removed AF_83XX_NO_FWDUMP flag and directly checking IDC_CTRL bit1
while taking minidump, to check for graceful reset.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
For ISP8xxx, adapter initialization is not retried if
qla4xxx_initialize_adapter fails.
Fix:
If qla4xxx_initialize_adapter fails, first check if failure is due to IRQs not
attached in order to skip retrial, then free the IRQs and then retry
initializing the adapter.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Setting DMA bit mask 64 and roll back to 32 if not supported.
Signed-off-by: Minh Tran <minhduc.tran@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
scsi_cmnd n io_task was not NULL when
- Link goes down while IO was happening and session is closed.
- Task for which TMF was sent.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In iSCSI Boot scenario, when machine is reboot/shutdown phase
the active sessions are not closed. Driver queue cleanup is
done as part of unload and device is disabled.
Sessions are still active, iSCSI commands are issued from
session which comes to driver, as driver cleanup and device
disabled there is kernel stack dump with errors.
Fix is invoking iscsi_session_failure with ISCSI_ERR_INVALID_HOST
on all the active sessions when shutdown routine is called.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The doorbel format has been updated to support additonal functionalities
of SKH-R adapter. These changes are made such that older FW also works fine.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The 100Mbps port speed macro used was not proper.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When an MBX command timeout happens,the resources associated with
the MBX command were freed. If FW were to give the response to
host after the timeout value set by driver then driver crashes as the MBX Cmd
resources were already freed.
This patch fixes this issue by maintaing a state flag for each of
the MBX command posted/timedout/completed.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
On encountering unexpected error conditions from driver initiated
commands, print something useful like CDB and sense data rather than
something useless like the kernel virtual address of the command buffer.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Do no rescan on every events -- way too many rescans are
triggered if we don't filter the events. Limit rescans
to be triggered by the following set of events:
* controller state change
* enclosure hot plug
* physical drive state change
* logical drive state change
* redundant controller state change
* accelerated io enabled/disabled
* accelerated io configuration change
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Don't wait for *all* commands to complete, only for accelerated mode
commands.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add controller-based data-at-rest encryption compatibility
to ioaccel2 path (HP SSD Smart Path).
Encryption feature requires driver to supply additional fields
for encryption enable, tweak index, and data encryption key index
in the ioaccel2 request structure.
Encryption enable flag and data encryption key index come from
raid_map data structure from raid offload command.
During ioaccel2 submission, check device structure's raid map to see if
encryption is enabled for the device. If so, call new function below.
Add function set_encrypt_ioaccel2 to set encryption flag, data encryption key
index, and calculate tweak value from request's logical block address.
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Change the handling of HP SSD Smart Path errors with status:
0x02 CHECK CONDITION
0x08 BUSY
0x18 RESERVATION CONFLICT
0x40 TASK ABORTED
So that they get retried on the RAID Path.
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Code was confused and assumed that page zero was not
VPD page and all non-zero pages were VPD pages.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allow driver to schedule a rescan whenever a request fails on the ioaccel2 path.
This eliminates the possibility of driver getting stuck in non-ioaccel mode.
IOaccel mode (HP SSD Smart Path) is disabled by driver upon error detection.
Driver relied on idea that request would be retried through normal path, and a
subsequent error would occur on that path, and be processed by controller
firmware. As part of that process, controller disables ioaccel mode and later
reinstates it, signalling driver to change modes.
In some error cases, the error will not duplicate on the standard path,
so the driver could get stuck in non-ioaccel mode.
To avoid that, we allow driver to request a rescan during the next run of the
rescan thread.
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allow SSD Smart Path for a controller to be disabled by
the user, regardless of settings in controller firmware
or array configuration.
To disable: echo 0 > /sys/class/scsi_host/host<id>/acciopath_status
To re-enable: echo 1 > /sys/class/scsi_host/host<id>/acciopath_status
To check state: cat /sys/class/scsi_host/host<id>/acciopath_status
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Load balance across members of a N-way mirror set, and
handle the meta-RAID levels: R10, R50, R60.
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Otherwise we could wind up using incorrect raid map data, and
then very bad things would likely happen.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Underlying firmware cannot handle task abort on accelerated path (SSD Smart Path).
Change abort requests for accelerated path commands to physical target reset.
Send reset request on normal IO path.
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Mike Miller <michael.miller@canonical.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Joe Handzik <Joseph.T.Handzik@hp.com>
Signed-off-by: Mike Miller <michael.miller@canonical.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Mike MIller <michael.miller@canonical.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Mike Miller <michael.miller@canonical.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Mike Miller <michael.miller@canonical.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* Do not check event bits on locked up controllers to
see if they need to be rescanned.
* Do not initiate any device rescans on controllers
which are known to be locked up.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For shared SAS configurations, hosts need to poll Smart Arrays
periodically in order to be able to detect configuration changes
such as logical drives being added or removed from remote hosts.
A register on the controller indicates when such events have
occurred, and the driver polls the register via a workqueue
and kicks off a rescan of devices if such an event is detected.
Additionally, changes to logical drive raid offload eligibility
are autodetected in this way.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When rescanning for logical drives, store information about whather
raid offload is enabled for each logical drive, and update the driver's
internal record of this.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This enables sending i/o's destined for RAID logical drives
which can be serviced by a single physical disk down a different,
faster i/o path directly to physical drives for certain logical
volumes on SSDs bypassing the Smart Array RAID stack for a
performance improvement.
Signed-off-by: Matt Gates <matthew.gates@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Mike Miller <michael.miller@canonical.com>
Signed-off-by: Don Brace <brace@beardog.cce.hp.com>
Signed-off-by: Joe Handzik <joseph.t.handzik@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For "mode 1" io accelerated commands, the command tag is in
a different location than for commands that go down the normal
RAID path, so the abort handler needs to take this into account.
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Mike Miller <michael.miller@canonical.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When commands sent down the "fast path" fail, they must be re-tried down the
normal RAID path. We do this by kicking i/o's back to the scsi mid layer with
a DID_SOFT_ERROR status, which causes them to be retried. This won't work for
SG_IO's and other non REQ_TYPE_FS i/o's which could get kicked all the way back
to the application, which may have no idea that the command needs resubmitting
and likely no way to resubmit it in such a way the that driver can recognize it
as a resubmit and send it down the normal RAID path. So we just always send
non REQ_TYPE_FS i/o's down the normal RAID path, never down the "fast path".
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For certain i/o's to certain devices (unmasked physical disks) we
can bypass the RAID stack firmware and do the i/o to the device
directly and it will be faster.
Signed-off-by: Matt Gates <matthew.gates@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is normally optional, but for SSD Smart Path support (in
subsequent patches) it is required.
Signed-off-by: Matt Gates <matthew.gates@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There is an extended report luns command which contains
additional information about physical devices. In particular
we need to get the physical device handle so we can use an
alternate i/o path for fast physical devices like SSDs so
we can speed up certain i/o's by bypassing the RAID stack
code in the controller firmware.
Signed-off-by: Matt Gates <matthew.gates@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
spin_lock_irqsave for the HBA lock is called in one function where flag
is local to that function. Another function is called from the first
function where lock has to be released using spin_unlock_irqrestore for
calling task_done of libsas. In the second function also flag is declared
and used. For calling task_done there is no need to enable the irq. So
instead of using spin_lock_irqsave and spin_unlock_irqrestore, spin_lock
and spin_unlock is used now. This also avoids passing the flags across all
the functions where HBA lock is being used. Also removed redundant code.
Reported-by: Jason Seba <jason.seba42@gmail.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Signed-off-by: Viswas G <viswas.g@pmcs.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit 254f796b9f updated
the driver to use 16 MSI-X vectors, despite the fact that
older controllers would provide only 4.
This was causing MSI-X registration to drop down to INTx
mode. But as the controller support performant mode, the
initialisation will become confused and cause the machine
to stall during boot.
This patch fixes up the MSI-X registration to re-issue
the pci_enable_msix() call with the correct number of
MSI-X vectors. With that the hpsa driver continues to
works on older controllers like the P200.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes kernel panic issue while booting into the kdump kernel.
We have triggered crash and kdump vmcore was successful. No issues seen while
booting into the OS.
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
pthru32->dataxferlen comes from the user so we need to check that it's
not too large so we don't overflow the buffer.
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch makes reject messages show right value for opcode and itt, which
is converse previously.
Signed-off-by: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixed following smatch warnings in bfa.
drivers/scsi/bfa/bfa_ioc.c:3882 bfa_sfp_show_comp() error: memcpy()
'des' too small (64 vs 248)
drivers/scsi/bfa/bfa_ioc.c:6859 bfa_flash_status_read() warn: unsigned
'status' is never less than zero.
drivers/scsi/bfa/bfa_ioc.c:6881 bfa_flash_status_read() warn: unsigned
'status' is never less than zero.
drivers/scsi/bfa/bfa_ioc.c:6917 bfa_flash_read_start() warn: unsigned
'status' is never less than zero.
drivers/scsi/bfa/bfa_ioc.c:7043 bfa_flash_raw_read() warn: unsigned
'status' is never less than zero.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add the missing unlock before return from function bfad_iocmd_cfg_trunk()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the host template doesn't declare an eh_host_reset_handler
the eh_deadline mechanism is pointless and will set the
device to offline. So disable eh_deadline if no
eh_host_reset_handler is present.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the highly unusual case where two threads are running concurrently through
the scanning code scanning the same target, we run into the situation where
one may allocate the target while the other is still using it. In this case,
because the reap checks for STARGET_CREATED and kills the target without
reference counting, the second thread will do the wrong thing on reap.
Fix this by reference counting even creates and doing the STARGET_CREATED
check in the final put.
Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org # delay backport for 2 months for field testing
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch eliminates the reap_ref and replaces it with a proper kref.
On last put of this kref, the target is removed from visibility in
sysfs. The final call to scsi_target_reap() for the device is done from
__scsi_remove_device() and only if the device was made visible. This
ensures that the target disappears as soon as the last device is gone
rather than waiting until final release of the device (which is often
too long).
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org # delay backport by 2 months for field testing
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This makes sure format strings cannot leak into the printk call via the
constructed buffer.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Report from coverity
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix module parameter descriptions mentioning default values that no longer
match the code.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
qla2x00_mem_alloc() returns 1 on success and -ENOMEM on failure. On the
one hand the caller assumes non-zero is success but on the other hand
the caller also assumes that it returns an error code.
I've fixed it to return zero on success and a negative error code on
failure. This matches the documentation as well.
[jejb: checkpatch fix]
Fixes: e315cd28b9 ('[SCSI] qla2xxx: Code changes for qla data structure refactoring')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
isci is needlessly tying libata's hands by returning
SAM_STAT_CHECK_CONDITION to some ata errors. Instead, prefer
SAS_PROTO_RESPONSE to let libata (via sas_ata_task_done()) disposition
the device-to-host fis.
For example isci is triggering an HSM Violation where AHCI is showing a
simple media error for the same bus condition:
isci:
ata7.00: failed command: READ VERIFY SECTOR(S)
ata7.00: cmd 40/00:01:00:00:00/00:00:00:00:00/e0 tag 0
res 01/04:00:00:00:00/00:00:00:00:00/e0 Emask 0x3 (HSM violation)
ahci:
ata6.00: failed command: READ VERIFY SECTOR(S)
ata6.00: cmd 40/00:01:00:00:00/00:00:00:00:00/e0 tag 0
res 51/40:01:00:00:00/00:00:00:00:00/e0 Emask 0x9 (media error)
Note that the isci response matches this from sas_ata_task_done():
/* We saw a SAS error. Send a vague error. */
[..]
dev->sata_dev.fis[3] = 0x04; /* status err */
dev->sata_dev.fis[2] = ATA_ERR;
The end effect is that isci is needlessly triggering hard resets when
they are not necessary.
Reported-by: Xun Ni <xun.ni@intel.com>
Tested-by: Nelson Cheng <nelson.cheng@intel.com>
Acked-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libsas sometimes short circuits timeouts to force commands into error
recovery. It is misleading to log that the command timed-out in
sas_scsi_timed_out() when in fact it was just queued for error handling.
It's also redundant in the case of a true timeout as libata eh will
detect and report timeouts via it's AC_ERR_TIMEOUT facility.
Given that some environments consider "timeout" errors to be indicative
of impending device failure demote the sas_scsi_timed_out() timeout
message to be disabled by default. This parallels ata_scsi_timed_out().
[jejb: checkpatch fix]
Reported-by: Xun Ni <xun.ni@intel.com>
Tested-by: Nelson Cheng <nelson.cheng@intel.com>
Acked-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Send aborts to the firmware via the request/response queue mechanism.
Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Fix interpreting the wrong IOCB type for task management
functions in the response path.
- Merge the task management function handling for various adapters.
Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allow for the capture of a firmware dump but have a sysfs node
(allow_cna_fw_dump) to allow the feature to be enabled/disabled dynamically.
The default is off.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Tell the mid-layer that number of commands we can queue is the available
resources we have minus a small amount for internal commands.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
SCSI retry delay upon SAM_STAT_BUSY/_SET_FULL was not being handled
in bnx2fc. This patch adds such handling by returning TARGET_BUSY
to the SCSI ML for the corresponding LUN until the retry timer expires.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The problem has been identified to be a change in the scsi_remove_device
path where a call to the pm_runtime_set_memalloc_noio was added when
del_gendisk is called in this path. Note that the new pm routine
attempts to cycle through all parent devices from the FC target device
to set the memalloc_noio flag. Because of this new change, a dependency
was created between the FC target device and the parent netdev device
in the destroy path.
In order to synchronized the destroy paths, bnx2fc has been modified
to flush all destroy workqueues in the NETDEV_UNREGISTER return path.
[ 4.123584] BUG: soft lockup - CPU#8 stuck for 22s! [kworker/8:3:8082]
[ 4.123713] Call Trace:
[ 4.123719] [<ffffffff815dfbe0>] klist_next+0x20/0xf0
[ 4.123725] [<ffffffff813e9220>] ? pm_save_wakeup_count+0x70/0x70
[ 4.123731] [<ffffffff813d9e4e>] device_for_each_child+0x4e/0x70
[ 4.123735] [<ffffffff813e9554>] pm_runtime_set_memalloc_noio+0x94/0xf0
[ 4.123740] [<ffffffff812d4d74>] del_gendisk+0x264/0x2a0
[ 4.123747] [<ffffffffa00c6dc9>] sd_remove+0x69/0xb0 [sd_mod]
[ 4.123751] [<ffffffff813de24f>] __device_release_driver+0x7f/0xf0
[ 4.123754] [<ffffffff813de2e3>] device_release_driver+0x23/0x30
[ 4.123757] [<ffffffff813ddab4>] bus_remove_device+0xf4/0x170
[ 4.123760] [<ffffffff813da475>] device_del+0x135/0x1d0
[ 4.123765] [<ffffffff81411b75>] __scsi_remove_device+0xc5/0xd0
[ 4.123768] [<ffffffff81411ba6>] scsi_remove_device+0x26/0x40
[ 4.123770] [<ffffffff81411d40>] scsi_remove_target+0x160/0x210
[ 4.123775] [<ffffffffa0420e4c>] fc_rport_final_delete+0xac/0x1f0 [scsi_transport_fc]
[ 4.123780] [<ffffffff810774ab>] process_one_work+0x17b/0x460
[ 4.123783] [<ffffffff8107825b>] worker_thread+0x11b/0x400
[ 4.123786] [<ffffffff81078140>] ? rescuer_thread+0x3e0/0x3e0
[ 4.123791] [<ffffffff8107e9c0>] kthread+0xc0/0xd0
[ 4.123794] [<ffffffff8107e900>] ? kthread_create_on_node+0x110/0x110
[ 4.123798] [<ffffffff8160ceec>] ret_from_fork+0x7c/0xb0
[ 4.123801] [<ffffffff8107e900>] ? kthread_create_on_node+0x110/0x110
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
pm80xx_get_gsm_dump() was returning "1" in error case
instead of negative error value.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Removed redundant code snippets in pm8001_hwi.c and
pm8001_ctl.c
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This was a debugging measure to toggle enabled/disabled
when testing. But for real production setups, it's not
safe to toggle this setting without either reloading
drivers of quiescing IO first. Neither of which the toggle
enforces.
Additionally, it makes drivers deal with the conditional
state.
Remove it completely. It's up to the driver whether iopoll
is enabled or not.
Signed-off-by: Jens Axboe <axboe@fb.com>
If the initialization of storvsc fails, the storvsc_device_destroy()
causes NULL pointer dereference.
storvsc_bus_scan()
scsi_scan_target()
__scsi_scan_target()
scsi_probe_and_add_lun(hostdata=NULL)
scsi_alloc_sdev(hostdata=NULL)
sdev->hostdata = hostdata
now the host allocation fails
__scsi_remove_device(sdev)
calls sdev->host->hostt->slave_destroy() ==
storvsc_device_destroy(sdev)
access of sdev->hostdata->request_mempool
Signed-off-by: Ales Novak <alnovak@suse.cz>
Signed-off-by: Thomas Abraham <tabraham@suse.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
sleep_on is known broken and going away. The atari_scsi driver is one of
two remaining users in the falcon_get_lock() function, which is a rather
crazy piece of code. This does not attempt to fix the driver's locking
scheme in general, but at least prevents falcon_get_lock from going to
sleep when no other thread holds the same lock or tries to get it,
and we no longer schedule with irqs disabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[MSch: fixed completion conditions missed in Arnds' original RFC patch]
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: James E.J. Bottomley <JBottomley@parallels.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
In the first place, the loop 'for' in the macro 'for_each_isci_host'
(drivers/scsi/isci/host.h:314) is incorrect, because it accesses
the 3rd element of 2 element array. After the 2nd iteration it executes
the instruction:
ihost = to_pci_info(pdev)->hosts[2]
(while the size of the 'hosts' array equals 2) and reads an
out of range element.
In the second place, this loop is incorrectly optimized by GCC v4.8
(see http://marc.info/?l=linux-kernel&m=138998871911336&w=2).
As a result, on platforms with two SCU controllers,
the loop is executed more times than it can be (for i=0,1 and 2).
It causes kernel panic during entering the S3 state
and the following oops after 'rmmod isci':
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff8131360b>] __list_add+0x1b/0xc0
Oops: 0000 [#1] SMP
RIP: 0010:[<ffffffff8131360b>] [<ffffffff8131360b>] __list_add+0x1b/0xc0
Call Trace:
[<ffffffff81661b84>] __mutex_lock_slowpath+0x114/0x1b0
[<ffffffff81661c3f>] mutex_lock+0x1f/0x30
[<ffffffffa03e97cb>] sas_disable_events+0x1b/0x50 [libsas]
[<ffffffffa03e9818>] sas_unregister_ha+0x18/0x60 [libsas]
[<ffffffffa040316e>] isci_unregister+0x1e/0x40 [isci]
[<ffffffffa0403efd>] isci_pci_remove+0x5d/0x100 [isci]
[<ffffffff813391cb>] pci_device_remove+0x3b/0xb0
[<ffffffff813fbf7f>] __device_release_driver+0x7f/0xf0
[<ffffffff813fc8f8>] driver_detach+0xa8/0xb0
[<ffffffff813fbb8b>] bus_remove_driver+0x9b/0x120
[<ffffffff813fcf2c>] driver_unregister+0x2c/0x50
[<ffffffff813381f3>] pci_unregister_driver+0x23/0x80
[<ffffffffa04152f8>] isci_exit+0x10/0x1e [isci]
[<ffffffff810d199b>] SyS_delete_module+0x16b/0x2d0
[<ffffffff81012a21>] ? do_notify_resume+0x61/0xa0
[<ffffffff8166ce29>] system_call_fastpath+0x16/0x1b
The loop has been corrected.
This patch fixes kernel panic during entering the S3 state
and the above oops.
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Reviewed-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Tested-by: Lukasz Dorau <lukasz.dorau@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Remove an erroneous BUG_ON() in the case of a hard reset timeout. The
reset timeout handler puts the port into the "awaiting link-up" state.
The timeout causes the device to be disconnected and we need to be in
the awaiting link-up state to re-connect the port. The BUG_ON() made
the incorrect assumption that resets never timeout and we always
complete the reset in the "resetting" state.
Testing this patch also uncovered that libata continues to attempt to
reset the port long after the driver has torn down the context. Once
the driver has committed to abandoning the link it must indicate to
libata that recovery ends by returning -ENODEV from
->lldd_I_T_nexus_reset().
Cc: <stable@vger.kernel.org>
Acked-by: Lukasz Dorau <lukasz.dorau@intel.com>
Reported-by: David Milburn <dmilburn@redhat.com>
Reported-by: Xun Ni <xun.ni@intel.com>
Tested-by: Xun Ni <xun.ni@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This fixes requesting of the MSI-X vectors for the base response queue.
The iteration in the for loop in qla24xx_enable_msix() was incorrect.
We should only iterate of the first two MSI-X vectors and not the total
number of MSI-X vectors that have given to the driver for this device
from pci_enable_msix() in this function.
Cc: <stable@vger.kernel.org>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull SCSI target fixes from Nicholas Bellinger:
"The bulk of the series are bugfixes for qla2xxx target NPIV support
that went in for v3.14-rc1. Also included are a few DIF related
fixes, a qla2xxx fix (Cc'ed to stable) from Greg W., and vhost/scsi
protocol version related fix from Venkatesh.
Also just a heads up that a series to address a number of issues with
iser-target active I/O reset/shutdown is still being tested, and will
be included in a separate -rc6 PULL request"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
vhost/scsi: Check LUN structure byte 0 is set to 1, per spec
qla2xxx: Fix kernel panic on selective retransmission request
Target/sbc: Don't use sg as iterator in sbc_verify_read
target: Add DIF sense codes in transport_generic_request_failure
target/sbc: Fix sbc_dif_copy_prot addr offset bug
tcm_qla2xxx: Fix NAA formatted name for NPIV WWPNs
tcm_qla2xxx: Perform configfs depend/undepend for base_tpg
tcm_qla2xxx: Add NPIV specific enable/disable attribute logic
qla2xxx: Check + fail when npiv_vports_inuse exists in shutdown
qla2xxx: Fix qlt_lport_register base_vha callback race
The SGI Visual Workstation seems to be dead; remove support so we
don't have to continue maintaining it.
Cc: Andrey Panin <pazke@donpac.ru>
Cc: Michael Reed <mdr@sgi.com>
Link: http://lkml.kernel.org/r/530CFD6C.7040705@zytor.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
A selective retransmission request (SRR) is a fibre-channel
protocol control request which provides support for requesting
retransmission of a data sequence in response to an issue such as
frame loss or corruption. These events are experienced
infrequently in fibre-channel based networks which makes
it difficult to test and assess codepaths which handle these
events.
We were fortunate enough, for some definition of fortunate, to
have a metro-area single-mode SAN link which, at 10 GBPS
sustained load levels, would consistently generate SRR's in
a SCST based target implementation using our SCST/in-kernel
Qlogic target interface driver. In response to an SRR the
in-kernel Qlogic target driver immediately panics resulting
in a catastrophic storage failure for serviced initiators.
The culprit was a debug statement in the qla_target.c file which
does not verify that a pointer to the SCSI CDB is not null.
The unchecked pointer dereference results in the kernel panic
and resultant system failure.
The other two references to the SCSI CDB by the SRR handling code
use a ternary operator to verify a non-null pointer is being
acted on. This patch simply adds a similar test to the implicated
debug statement.
This patch is a candidate for any stable kernel being maintained
since it addresses a potentially catastrophic event with
minimal downside.
Signed-off-by: Dr. Greg Wettstein <greg@enjellic.com>
Cc: <stable@vger.kernel.org> #3.5+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes the NAA formatted name used by EVPD=0x83
device identifer to reflect the proper NPIV enabled WWPN.
Cc: Sawan Chandak <sawan.chandak@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch performs configfs_depend_item() during TPG enable for
base_tpg (eg: non-NPIV) ports, and configfs_undepend_item() during
TPG disable for base_tpg.
This is done to ensure that any attempt to configfs rmdir a base_tpg
with active NPIV ports will fail with -EBUSY, until all associated
NPIV ports have been explicitly shutdown and base_tpg disabled.
Note that the actual configfs_[un]depend_item() is done from seperate
process context, as these are not intended to be called directly
from configfs callbacks.
Cc: Sawan Chandak <sawan.chandak@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds seperate logic for NPIV specific enable/disable
attribute logic, as NPIV vs. non-NPIV enable/disable ends up being
different enough to warrent seperate logic for setting configfs
tpg_group dependencies in the non-NPIV case.
Cc: Sawan Chandak <sawan.chandak@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds an check to qlt_stop_phase1() to avoid shutdown
when the base_vha contains a non-zero fc_host->npiv_vports_inuse
count.
This includes holding qla_tgt_mutex in qlt_stop_phase1() between
the fc_host->npiv_vports_inuse check + setting of tgt->tgt_stop to
avoid a possible race between qlt_lport_register() -> tcm_qla2xxx
-> tcm_qla2xxx_lport_register_npiv_cb() calling fc_vport_create().
Cc: Sawan Chandak <sawan.chandak@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch closes a race between qlt_lport_register() and
tcm_qla2xxx callback logic by holding qla_tgt_mutex before
making the callback.
In order for this to work, the qlt_add_target() and
qlt_remove_target() code has been changed to avoid the
accessing qla_tgt_mutex + list_[add,del] for NPIV enabled
ports.
This bug introduced in v3.14-rc1 code with commit 49a47f2.
Cc: Sawan Chandak <sawan.chandak@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fix spelling typo in Documentation/DocBook.
It is because .html and .xml files are generated by make htmldocs,
I have to fix a typo within the source files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull ARM fixes from Russell King:
"A range of ARM fixes. Biggest change is the stage-2 attributes used
for for hyp mode which were wrong. I've killed some bits in a couple
of DT files which turned out not to be required, and a few other
fixes.
One fix touches code outside of arch/arm, which is related to sorting
out the DMA masks correctly. There is a long standing issue with the
conversion from PFNs to addresses where people assume that shifting an
unsigned long left by PAGE_SHIFT results in a correct address. This
is not the case with C: the integer promotion happens at assignment
after evaluation. This fixes the recently introduced dma_max_pfn()
function, but there's a number of other places where we try this
directly on an unsigned long in the mm code"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7957/1: add DSB after icache flush in __flush_icache_all()
Fix uses of dma_max_pfn() when converting to a limiting address
ARM: 7955/1: spinlock: ensure we have a compiler barrier before sev
ARM: 7953/1: mm: ensure TLB invalidation is complete before enabling MMU
ARM: 7952/1: mm: Fix the memblock allocation for LPAE machines
ARM: 7950/1: mm: Fix stage-2 device memory attributes
ARM: dts: fix spdif pinmux configuration
We must use a 64-bit for this, otherwise overflowed bits get lost, and
that can result in a lower than intended value set.
Fixes: 8e0cb8a1f6 ("ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations")
Fixes: 7d35496dd9 ("ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations")
Tested-Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The only place this struct member is touched is in one INIT_LIST_HEAD.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
driver-core now supports synchrnous self-deletion of attributes and
the asynchrnous removal mechanism is scheduled for removal. Use it
instead of device_schedule_callback(). This makes "delete" behave
synchronously.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- add support for SCSI Referrals (Hannes)
- add support for T10 DIF into target core (nab + mkp)
- add support for T10 DIF emulation in FILEIO + RAMDISK backends (Sagi + nab)
- add support for T10 DIF -> bio_integrity passthrough in IBLOCK backend (nab)
- prep changes to iser-target for >= v3.15 T10 DIF support (Sagi)
- add support for qla2xxx N_Port ID Virtualization - NPIV (Saurav + Quinn)
- allow percpu_ida_alloc() to receive task state bitmask (Kent)
- fix >= v3.12 iscsi-target session reset hung task regression (nab)
- fix >= v3.13 percpu_ref se_lun->lun_ref_active race (nab)
- fix a long-standing network portal creation race (Andy)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (51 commits)
target: Fix percpu_ref_put race in transport_lun_remove_cmd
target/iscsi: Fix network portal creation race
target: Report bad sector in sense data for DIF errors
iscsi-target: Convert gfp_t parameter to task state bitmask
iscsi-target: Fix connection reset hang with percpu_ida_alloc
percpu_ida: Make percpu_ida_alloc + callers accept task state bitmask
iscsi-target: Pre-allocate more tags to avoid ack starvation
qla2xxx: Configure NPIV fc_vport via tcm_qla2xxx_npiv_make_lport
qla2xxx: Enhancements to enable NPIV support for QLOGIC ISPs with TCM/LIO.
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
IB/isert: pass scatterlist instead of cmd to fast_reg_mr routine
IB/isert: Move fastreg descriptor creation to a function
IB/isert: Avoid frwr notation, user fastreg
IB/isert: seperate connection protection domains and dma MRs
tcm_loop: Enable DIF/DIX modes in SCSI host LLD
target/rd: Add DIF protection into rd_execute_rw
target/rd: Add support for protection SGL setup + release
target/rd: Refactor rd_build_device_space + rd_release_device_space
target/file: Add DIF protection support to fd_execute_rw
target/file: Add DIF protection init/format support
...
Pull core block IO changes from Jens Axboe:
"The major piece in here is the immutable bio_ve series from Kent, the
rest is fairly minor. It was supposed to go in last round, but
various issues pushed it to this release instead. The pull request
contains:
- Various smaller blk-mq fixes from different folks. Nothing major
here, just minor fixes and cleanups.
- Fix for a memory leak in the error path in the block ioctl code
from Christian Engelmayer.
- Header export fix from CaiZhiyong.
- Finally the immutable biovec changes from Kent Overstreet. This
enables some nice future work on making arbitrarily sized bios
possible, and splitting more efficient. Related fixes to immutable
bio_vecs:
- dm-cache immutable fixup from Mike Snitzer.
- btrfs immutable fixup from Muthu Kumar.
- bio-integrity fix from Nic Bellinger, which is also going to stable"
* 'for-3.14/core' of git://git.kernel.dk/linux-block: (44 commits)
xtensa: fixup simdisk driver to work with immutable bio_vecs
block/blk-mq-cpu.c: use hotcpu_notifier()
blk-mq: for_each_* macro correctness
block: Fix memory leak in rw_copy_check_uvector() handling
bio-integrity: Fix bio_integrity_verify segment start bug
block: remove unrelated header files and export symbol
blk-mq: uses page->list incorrectly
blk-mq: use __smp_call_function_single directly
btrfs: fix missing increment of bi_remaining
Revert "block: Warn and free bio if bi_end_io is not set"
block: Warn and free bio if bi_end_io is not set
blk-mq: fix initializing request's start time
block: blk-mq: don't export blk_mq_free_queue()
block: blk-mq: make blk_sync_queue support mq
block: blk-mq: support draining mq queue
dm cache: increment bi_remaining when bi_end_io is restored
block: fixup for generic bio chaining
block: Really silence spurious compiler warnings
block: Silence spurious compiler warnings
block: Kill bio_pair_split()
...
- Flow steering for InfiniBand UD traffic
- IP-based addressing for IBoE aka RoCE
- Pass SRP submaintainership from Dave to Bart
- SRP transport fixes from Bart
- Add the new Cisco usNIC low-level device driver
- Various other fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=wAWA
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.14:
- Flow steering for InfiniBand UD traffic
- IP-based addressing for IBoE aka RoCE
- Pass SRP submaintainership from Dave to Bart
- SRP transport fixes from Bart
- Add the new Cisco usNIC low-level device driver
- Various other fixes"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (75 commits)
IB/mlx5: Verify reserved fields are cleared
IB/mlx5: Remove old field for create mkey mailbox
IB/mlx5: Abort driver cleanup if teardown hca fails
IB/mlx5: Allow creation of QPs with zero-length work queues
mlx5_core: Fix PowerPC support
mlx5_core: Improve debugfs readability
IB/mlx5: Add support for resize CQ
IB/mlx5: Implement modify CQ
IB/mlx5: Make sure doorbell record is visible before doorbell
mlx5_core: Use mlx5 core style warning
IB/mlx5: Clear out struct before create QP command
mlx5_core: Fix out arg size in access_register command
RDMA/nes: Slight optimization of Ethernet address compare
IB/qib: Fix QP check when looping back to/from QP1
RDMA/cxgb4: Fix gcc warning on 32-bit arch
IB/usnic: Remove unused includes of <linux/version.h>
RDMA/amso1100: Add check if cache memory was allocated before freeing it
IPoIB: Report operstate consistently when brought up without a link
IB/core: Fix unused variable warning
RDMA/cma: Handle global/non-linklocal IPv6 addresses in cma_check_linklocal()
...
Vikas Chaudhary
Tej Parkash
Nilesh Javali
Jayamohan Kallickal
Stephen M. Cameron
Scott Teel
Mike MIller
Matt Gates
Matt Gates
Suresh Thiagarajan
Hannes Reinecke
Mahesh Rajashekhara
Dan Carpenter
Vaughan Cao
Vijaya Mohan Guvva
Wei Yongjun
James Bottomley
Bradley Grove
Kees Cook
Daeseok Youn
James Smart
Chad Dupuis
Steven J. Magnani
Dan Williams
Armen Baloyan
Saurav Kashyap
Atul Deshmukh
Joe Carnuccio
Eddie Wai
Viswas G
Jens Axboe
Ales Novak
Arnd Bergmann
Giridhar Malavali
Lukasz Dorau
Mike Christie
Greg Kroah-Hartman
Linus Torvalds
H. Peter Anvin
Dr. Greg Wettstein
Nicholas Bellinger
Jiri Kosina
Masanari Iida
Russell King
Roland Dreier
Tejun Heo